Special repair renovation of house No. 12A ADC Residence in Sector 15A Faridabad District

Amount

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete [HSR 30.21]

Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete [HSR 11.58]

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface -Water thinnable cement primer [HSR 11.67.1](Labour rate only)

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work [HSR 30.27 .1] (Labour rate only)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade - One or more coats on old work [HSR 30.28.1](Labour rate only)

Finishing walls with Acrylic Smooth exterior paint of required shade old work (One or more coat applied @ 0.90 litre/10 sqm) [HSR 30.37.2] (Labour rate only)

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by Engineer-in-charge. - All kinds of soil [4.12.1]

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead - Of area 3 sq. metres and below [HSR 5.29.1]

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead - For thickness of tiles 10 mm to 25 mm [HSR 5.43.1]

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead [HSR 5.45]

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead [HSR 5.48]

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved [HSR 5.70]

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1: 1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 graded stone aggregate 20 mm nominal size) [HSR 6.16]

Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect above plinth level - Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, over1aps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. - Thermo-Mechanically Treated bars of grade Fe-500D or more [HSR 6.34.6]

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete [HSR 13.28]

Brick work with common burnt clay non-modular bricks of class designation 7.5 in foundation and plinth in - Cement mortar 1:6 (1 cement: 6 coarse sand) [HSR 7.21.2]

Brick work with common burnt clay non-modular bricks of class designation 7 .5 in superstructure above plinth level up to floor IV level in all shapes and sizes in - Cement mortar 1:6 (1 cement: 6 coarse sand) [HSR 7.22.2]

Providing and laying brick tiles over mumty roofs, grouted with cement mortar 1 :3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1 :3 (1cement : 3 fine sand) and finished neat:- With common burnt clay non-modular brick tiles of class designation 10 [HSR 9.14.1]

Providing and laying of base course of floors consisting of 100 mm thick cement 1 :8: 16 and 100 mm sand or stone filling [HSR 10.1]

Providing and laying of conglomerate floor 40mm thick cement concrete topping 1 :2:4 [HSR 10.8]

Fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1 :3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete [HSR 10.58] (Labour rate only) Tiles will be supplied by the Department)

Laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1 :4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. (HSR 10.63.2) Size of Tile 600x600 mm [HSR 10.63.2] (Labour rate only) Tiles will be supplied by the Department)

Laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1 :3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. (HSR 10.67.2) Size of Tile 600x600 mm.(HSR 10.67.2)(Labour rate only) Tiles will be supplied by the Department)

10 mm thick cement plaster -1 :3 (1 cement: 3 fine sand) [HSR 11.4.2]

12 mm cement plaster of mix - 1 :4 (1 cement: 4 fine sand) [HSR 11.5.3]

15 mm cement plaster on the rough side of single or half brick wall of mix - 1 :4 (1 cement: 4 fine sand) [HSR 11.6.1]

Providing and fixing wire gauge laminated veneer lumber shutters conforming to IS : 14616, using galvanised wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm as per IS :1568, for doors, windows and clerestory windows, including ISi marked M.S. pressed butt hinges bright finished of required size with necessary screws, as per directions of Engineer-in-charge: (Note:- Butt hinges and necessary screws shall be paid separately) - 35 mm thick shutters [HSR 12.20.1]

Providing and fixing pressed steel door frames conforming to IS: 4351,manufactured from commercial mild steel sheet of 2.0 mm thickness,including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 2.00 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S.pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge Fixing with adjustable lugs with split end tail to each jamb HSR 2021 [HSR 13.3.1.1]

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters - 30 mm thick including ISi marked Stainless Steel butt hinges with necessary screws [HSR 12.36.2]

Providing and laying damp-proof course with cement concrete 1 :2:4 (1 cement : 2 coarse sand (zone-Ill): 4 graded stone aggregate 12.5mm nominal size) - 25mm thick [HSR 6.8.3]

Providing reinforced by organic fibres and/or inorganic synthetic fibres cement 6 mm thick corrugated sheets (as per IS: 14871) roofing up to any pitch and fixing with polymer coated J, or L hooks, bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete (excluding the cost of purlins, rafters and trusses), including cutting sheets to size and shape wherever required. [HSR 9.35]

Providing and fixing panelling or panelling and glazing in panelled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick 4 mm thick glass pane (weight not less than 10kg/sqm). [HSR 12.9.7.1]

Providing and fixing Bamboo Jaffri/ fencing consisting of superior quality 25mm dia (Average) half cut bamboo placed vertically and fixed together with three numbers horizontal running members of Hollock wood in scantling of section 50X25 mm, fixed with nails and G.I wire on existing support complete as per direction of Engineer-in-charge [HSR 12.116]

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) [HSR 13.41]

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge- Concealed work, including cutting chases and making good the walls etc.- 20 mm nominal outer dia Pipes [HSR 22.86.2]

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge- Concealed work, including cutting chases and making good the walls etc.- 25 mm nominal outer dia Pipes [HSR 22.86.3]

Fixing white vitreous chinaware pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous chinaware flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, over flow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required - W.C. pan with ISi marked white solid plastic seat and lid [HSR 22.24.1](Labour rate only)

Fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require - White vitreous chinaware Wash basin size 630x450 mm with a pair of 15 mm C. P. brass pillar taps [HSR 22.1.1] (Labour rate only)

Fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 - 15mm nominal bore [HSR 22.108.1] (Labour rate only)

Fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. - 15 mm nominal bore [HSR 22.106.1] (Labour rate only)

Fixing Unplasticised PVC connection pipe with brass unions: 30 cm length - 15 mm nominal bore [HSR 22.101.1.1] (Labour rate only)

Fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge [HSR 22.109] (Labour rate only)

Providing and fixing kitchen sink including making all connections excluding cost of fittings. - White glazed fire clay sink of size 600x450x250 mm [HSR 22.13.1] (Labour rate only)

Fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. - Semi rigid pipe - 32 mm dia [HSR 22.14.1.1] (Labour rate only)

Fixing 15 mm C.P. brass Laboratory cock swan neck of best quality (to the approval of Engineer-in-charge) - Two way [HSR 22.8.2] (Labour rate only)

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: 100 mm diameter [HSR 22.102.1] (Labour rate only)

Fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms [HSR 22.127] (Labour rate only)

Fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing - Rectangular shape 453x357 mm [HSR 22.210.2] (Labour rate only)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank [HSR 22.181]

Fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gm [HSR 22.117]

Fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms [HSR 22.118]

Fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. - 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. [HSR 22.119.2]

Fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms [HSR 22.120]

Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. - 110 mm diameter [HSR 9.57.2]

Fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platfonns, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1 :4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels- Granite of any colour and shade- Area of slab over 0.50 sqm (HSR 8.26.2.2) (Granit shall be Supplied by the department)(Labour Rate)

Providing and fixing Pre-laminated medium density fibre board IS: 14587:1998 marked, with one side decorative lamination other side balancing lamination Grade-l(exterior grade) in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand (fittings to be paid separately)- Pre-laminated with decorative lamination one side and other side balancing lamination exterior Grade - I MDF Board 18 mm thick confirming to 15:14587 (HSR 18.12.1)

Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with- Decorative veneer facings of approved manufacture (HSR 8.19.1)

Providing & Fixing decorative high pressure laminated sheet of plain/ wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality- 1.0 mm thick (HSR 12.12.2)

Providing and fixing stainless steel baskets in kitchen ward robe of SS grade-304,crome finish fixed on channels of required size complete in all respect as desired by Engineer-in-charge. (The stainless steel basket shall be of premium quality of reputed manufacture) (NS) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material (i) Cutlery 17"x20"x4"

Multi Basket 17"x20"x6"

Grain Trolley 17"x20"x12"

Bottle Pull Out 10"x20"x8"

Plate 17"x20"x8"

Cup & Saucer 17"x20"x4"

Carrousal 27"

Channels 20"

Hinges

Handles

Edge Binding

Fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required- Kitchen sink without drain board- 610x460 mm bowl depth 200 mm (HSR 22.10.2.2) (Labour Rate)

Fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete- Flexible pipe- 32 mm dia (HSR 22.14.2.1)(Labour Rate)

Recovery Items: The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. . The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purpose in case the agency quotes lesser than reserve price.-Asbestos sheet @ 150/- Per Sqm(C) Door @ Rs. 400/- Per Cum

Door @ Rs. 400/- Per Cum

ARCTECH GREEN VENTURES