CERTAIN REPAIR FLOORING PLINTH PROTECTION AND JOINERY AT GEN ROAD, MAP QTR IN AB ROAD UNDER AGE B/R-IV OF GE AWC MHOW.

Amount

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size n. exc 1.5 Sqm each and removing from site complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size n. exceeding 1.5 Sqm and not exceeding 4.00 Sqm each and removing from site complete all as specified and as directed.

Taking down shutters of any description, area exceeding 1 Sqm and not exceeding 2.00 Sqm each complete all as specified and as directed.

Taking down and refixing in same opening wooden shutter exc 1 Sqm but not exc 2.00 Sqm including easing & adjusting and refixing with same hardware ect, complete all as specified and as directed.

Description same as per Item No. 4.00 above but without taking down of shutter n. exc 1 Sqm, complete all as specified and as directed.

M & L PCC 1:3:6 type C-1 using 20mm graded stone aggregate for hold fast blocks, including necessary form work for rough finished surfaces etc complete all as specified and as directed.

M & L 35mm thick, IInd class hard wood plain, framed, panelled factory made shutters (two panel) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and as directed.

M & L 35 mm thick, 2nd class hard wood , glazed & skeleton factory made shutters, open rebated & prepared to receive glass, gauze etc. (without sash-bars), edges of framing plain, chamfered or rounded fitted with cut and metred beads for securing glass etc., sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.20(a) complete all as specified and as directed.

S&F 35 mm thick factory made flush shutter, solid core construction with particle board core and ply wood face panels commecial type on both sides complete all as specified and as directed.

S&F Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as shown in drawing of relevant item in MES, schedule Part-II , 2020 as specified and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as shown in drawing of relevant item in MES, schedule Part-II , 2020 as specified and as directed.

S&F 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and as directed.

M&L Decorative tiles for gate wall Granite stone 18- 20 mm thick(of any type) work (table rubbed and polished) for wall lining (Veneering to wall) and laid on cill of parapet wall over and including 12 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite colour as per direction of GE, complete all as specified and as directed.

S&F Framed work such as grills,gratings, etc.. with ends of barsshouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.- 290. Gde-E-165, complete all as specified and as directed.

S & F aluminium window/ventilator/door in lieu of wooden made out of extruded powder coated aluminium sections, with sliding or openable shutters including frame and necessary jointing cleats, glazing clips, powder coated aluminium snap beading, screws etc complete and also including powder coated aluminium fittings such as cobra hinges, butt hinges, tower bolts, Star lock, hooks & eyes peg stays, rubber beading and handles including connected items with and including, complete all as specified and directed. NOTE :(i) Minimum thickness of powder coating shall be 15 micron for windows and 25 microns for doors. (ii) Rubber beading shall be measured and paid sepearately.

S&F 4mm thick plain sheet glass of ordinary quality for aluminium windows including rubber beading etc all as directed and specified.

S&F aluminium anodised grill and frame of approved make and pattern of 10mm thick fixed including F frame for aluminium windows, complete all as specified and as directed.

S & F rubber beading suitable for fixing 4 mm / 5 mm thick glass in aluminium window/door etc, complete all as specified and as directed.

M&L Preparation of new wooden surfaceof any description, not otherwise described, over 10cm width or girth and apply one coate of pink primer and two coates of synthetic enamel paint, complete all as specified and as directed.

M&L Preparation of old wooden surfaceof any description, not otherwise described, over 10cm width or girth and apply one coate of synthetic enamel paint, complete all as specified and as directed.

Taking down existing treatment and roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and as directed.

M&L Brushing neat cement slurry with 3 Kg of cement per Sqm mixed with and including chemical compound SUPER LATEX of DR. FIXIT of PIDILITE INDUSTRIES LTD. water and cement (1:4:7) mix or SBR LATEX of STP LTD, as per manufacturers instructions for bonding of old concrete surface to new concrete complete all as specified and as directed.

M & L 10 mm thick plaster in one layer in CM (1:3) over concrete roof padding, cement mortar mixed with and including chemical compound PIDIPROOF LW of DR FIXIT of PIDILITE INDUSTRIES LTD mixed in proportion 200 millilitre per 50 Kg cement or STP No. 1 (Liquid) of STP Ltd. in proportion 200 ml per 50 Kg cement as per manufacturers instructions and finishing the surface fair and even without using extra cement complete all as specified and as directed.

M&L Water proofing treatment on "Non approachable / non accessible roof" surface (Horizontal & Vertical surfaces) in following sequence through manufacturer / authorized applicator of the manufacturer all as specified and directed complete. (i) Properly cleaning and drying concrete surfaces. (ii) Applying a coat of oxidised bitumen based solvent primer 0.3 Kg / Sqm. (iii) APP based polymeric membrane of 3 mm thick reinforced with polyster non wove fabric laid with 100 mm over laps sealed and bounded to the surfaces by 'torchon' method. (iv) Applying coat of bitiminous aluminium paint @ 200 Gram / Sq M (minimum) in two coats complete all as specified and as directed.

Supply only liquid water proofing compound, complete all as specified and as directed.

S & F Butt hinges, 100 mm long medium weight, cold rolled mild steel, ISI marked complete all as specified and as directed.

S&F aluminium handles extruded type of size 125mm, complete all as specified and directed.

S & F 150 mm long, aluminium anodised, barrel tower bolts, of extruded section ISI markedcomplete all as specified and as directed.

Supply and fixing in repair 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed all as specified and directed.

S&F fixed 100mm hasp and staple mild steel safety type stove enamelled black including bolt to hinge plate and fixed with screw, complete all as specified and as directed.

S&F stainless steel wire cloth 0.56 mm nominal dia of wire and average width 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F as in repair stainless steel wire cloth 0.56 mm nominal dia of wire and average width 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F as in repair 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S & F Floor door stopper over all length 150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed.

S & F Aluminium Door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 900 mm in width and of weight not more than 35 kg and fixed, complete all as specified and as directed.

S & F Aluminium Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed, complete all as specified and as directed.

Dismantling of unframed/ framed boarding , any description,including fitting and fixtures fixed in any position with nails, complete all as specified and as directed.

S& F 18/19 mm thick Block boards, grade 2 quality, interior grade, commercial type, fixed with screws timber frame work as in cupboard , wardrobe etc, complete all as specified and as directed.

M & L 0.9 mm thick Decorative laminate type 1, of surface finish, colour and pattern as approved, fixed with approved adhesive over and including 12 mm thick plywood as per manufacturer's instructions complete all as directed and specified.

S&F Aluminium, anodised, barrel tower bolts of extruded section and fixed, 100 mm length of bolt, ISI marked complete all as specified and as directed.

S & F in repair 30 mm width of flaps (when open) Continous (piano) hinges , mild steel, bright finish or electrogalvanised complete all as directed and specified.

S&F Aluminium handles, cast type anodised 'D' shaped , 100mm long ISI marked, complete all as specified and as directed.

S&F in repair of continuous plano hinges mild steel bright finish or electro galvanised for 30mm thickness, complete all as specified and as directed.

S & F Plain fillets. Square, rectangular or triangular in section, clean swan, secured with nails or brads 2nd class softwood n. exc 3sq.cm, complete all as specified and as directed.

Demolition of brickwork or stone boulder masonary built in cement mortar including all quoins, arches, pillars etc, complete all as specified and as directed.

M&L for Brickwork with fly ash modular bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified and as directed.

M&L for Brick work with fly ash modular bricks, straight or curved on plan any radius in half brick thick wall with old size bricks built in cement mortar 1:4 complete all as specified and as directed.

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and as directed.

M&L for Rendering 10 mm thick in cement and sand mortar 1:6 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete .

Description same as per Item No. 49.00 above here-in-before, but 15mm thick in cement mortar 1:4 finished fair and even using integral water proofing compound. Note:- WPC shall be measured and paid separately.

M&L for Rendering 5 mm thick in cement and sand mortar 1:4 on concrete surfaces of ceiling including finishing the surface even and smooth without using extra cement complete.

M&L for Preparation of new plastered surfaces of wall applying two coat of oil bound distemper over one coat of alkali resistant paint & inculding 1mm thick wall care putty on wall compelete all as specified and directed.

Description same as per Item No. 52.00 above here-in-before, but on ceiling compelete all as specified and directed.

M&L Preparation of newly plastered surfaces of walls and applying two coats of cement base paint compelete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level ) complete.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 20 mm graded stone aggregate) as in plinth protection, surface finished even and smooth without using extra cement, laid in panels n exc 3 mtr long and joints shall be filled with the mixture of bitumen and sand in (1:3) by weight, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off premises complete all as specified and as directed.

M&L Rendering 10 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces for receiving of tiles using extra cement complete all as specified and directed

M&L for glazed ceramic tiles coloured digital with highlighter and approved design and pattern by G E of size 450x300 x 7mm thick on walls etc, set & jointed in neat cement slurry and pointed in white or colours cement to match the colour of tiles, complete all as specified and directed

M&L for glazed ceramic tiles coloured of size 300 x 200x 7mm thick in walls etc, set & jointed in neat cement slurry and pointed in white or colours cement to match the colour of tiles, complete all as specified and directed

M & L 25 mm thick PCC 1:2:4 type B-1, using 20 mm graded stone aggregate, including finishing surface of concrete topping even and rough compelete as in levelling work including demolition of existing concrete all as specified and directed.

M&L for screed bed 15mm thick in CM 1:6 complete all as specified and directed.

M&L for non skid cramic tiles colured of size area of each tile exc 0.18 Sqm but not exc 0.38 Sqm in flooor etc, jointed in neat cement slurry and pointed in white or colours cement to match complete all as specfied and directed

M&L for non skid cramic tiles colured of size area of each tile exc. 0.18 Sqm but not but not exc 0.38 Sqm in skriting ok dado jointed in neat cement slurry and pointed in white or colours cement to match complete all as specfied and directed

M&L for non skid-ceramic tiles coloured of size area of each tile exc. 0.06 Sqm but not exc. 0.11 Sqm 7-8 mm thick in floors etc, set & jointed in neat cement slurry and pointed in white or colours cement to match complete all as specified and directed

M & L Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed.

M&L 75mm thick PCC 1:4:8, type D-2 using 40 mm graded stone aggregate as in sub base for pavement, path, floor etc compelete all as specified and directed.

M &L for exterior wall decorating and water proofing treatment to wall surface by wire brushing in order to remove dust, dirt, loose particale, laitance. Thereafter wash the surface with clean water & allow to dry. fill vissible crack,joints by chemistic crackseal caulking compound and allow to dry for 24 hours. Apply a primer coat of chemistic Prime N Seal ( water base primer) and allow to dry for 6 hours. there after apply 02 coats of chemistik PDS-50 (WB high build Anti coronation coating cum water proofing) and shade by brush at the interval of 08 hours between the coat and allow to dry to match the existing shade Rate quoted shall included for scaffolding up to and including 04 Stories , covering etc. complete all as specified and as directed

S&F Heavy duty outdoor vitrified tiles 300mm x 300mm and 10mm thick complete all as specified and as directed.

Demolition of cement concrete in sunken floors incl. removing debriesh outside MD land complete all as specified and directed.

M&L Brushing neat cement slurry with 3.0kg of cement per sq. metre mixed with WPC @ 3% by weight of cement as per manufacturer's instruction to fill all hole and crack complete all as specified and as directed. Note:- Water tightness testing should be done after 24 hours complete all as specified and directed.

Material and labour for PCC (1:1 1/2 :3) type A-0 using 12.5 mm graded stone aggregate mixed with integral water proofing compound as per manufacturer instructions on bottom of sunken portion with proper slope towards spout, complete all as specified and as directed.. Note : Water proofing compound will be measured and paid separately.

Material and labour for plastering on vertical sides and top surface of CM (1:3) 15 mm thick mixed with water proofing compound as per manufacturer instructions. Plaster shall be extended over PCC coving when the same is green i.e. PCC & plaster be carried out at the same time, complete all as specified and as directed. Note : Water proofing compound will be measured and paid separately.

Material and labour for 2 coats of Dr. Fixit krystalline waterproofing coating compound applied after laying sewage/ plumbing pipes with fixtures in position, complete all as specified and as directed.

Material and labour for filling the sunken floor with PCC ( 1:5:10) type E-2 using 40 mm graded stone aggregate over the treated surface, complete all as specified and as directed.

M&L spouts of 50mm dia GI pipe light grade projecting 450mm clear of face outer wall with PVC mosquito proof cap on inner face of pipe shall be provided to drain out seepage water , if any. Note : Water tightness testing should be done after applying Dr Fixit epoxy compound, by pounding water for 72 hours & rectify defects if any till total elimination of defect. Rubbish to be removed outside MD land, complete all as specified and as directed.

Supply and fixing in repair PVC Flexible waste pipe 32/40 mm dia with socket for steel sink upto floor level and length not less than 0.60 M complete all as specified and directed.

S & F in repair light coloured vitreous china WHB white oval shape of 500mmx400mm (minimun) on new brackets excluding taps waste china & plug including bracket etc complete all as specified .

Supply and fixing in repair Vitreous China wash down water closet pan (Pedestal Pattern) and trap (standard pattern) coloured as approved including connection to drain (or outgoing pipe) and to flushing pipe anti syphonage pipe etc. and jointing complete with fixing bolts compelete all as specified and directed.

Supply and fixing in repair Vitreous China one piece water closet as approved including connection to drain (or outgoing pipe) and to flushing pipe anti syphonage pipe, seate cover and hidden acessories etc. and jointing complete with fixing bolts compelete all as specified and directed.

Supply and fixing in repair Plastic water closet seat,any colour as available, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and jointing complete.

S&F in repair CP brass health faucet fitted with bracket, screwed down for iron pipe or for brass ferrule complete all as specified and directed.

Supply & fixing in repair Jet spray for water closet pan pedestal pattern compelete all as specified and directed.

S& F in repair PVC low level flushing cistern, valveless, syphonic action type, 10 litres capacity with inlet, ball valve float and handle with and including brackets & PVC bend pipe 90 cm long etc, compelete all as specified and directed.

S & F in repair Sink with drainage board made out of stainless steel 1.00 mm thick sheet for kitchen with plugs, washers and wastes including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm with bowl size 410 mm x 330mm x 160mm compelete all as specified and directed.

S&F in repair stainless steel kitchen plate rack made out of 1mm thick stainless steel of size 900 x 600 mm of best quality of approved make, complete all as specified and as directed.

S&F in repair Tubular towel rail aluminium anodised 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls, compelete all as specified and directed.

S&F in repair PVC connection 15 mm size, of length 450 mm, with PTMT nuts supplied and fixed in repairs complete.

S&F in repair 32 mm bore waste coupling with fittings, brass, chromium plated for galzed ware sinks, basins etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end compelete all as specified and directed.

S&Fixed in repair PVC Flexible waste pipe 32 mm dia with socket for steel sink upto floor level and length not less than 0.60 M complete all as specified and directed.

S&F in repair Stainless steel gratings 100mm bore size fixed with cement motar compelete all as specified and directed.

Taking up or down steel tubing and connections, 15 mm bore fixed on walls, floors or ceiling etc compelete all as specified and directed.

Taking up or down steel tubing and connections, 20 mm bore fixed on walls, floors or ceiling etc compelete all as specified and directed.

S & F 16 mm bore of pipes 3-layer PP-R (Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot and cold water supply including all PP-R plain and brass threaded polypropylene random fittings fixed complete to walls, ceiling, or in floors etc complete.(Including all fitttings)

S & F 20 mm bore of pipes 3-layer PP-R (Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot and cold water supply including all PP-R plain and brass threaded polypropylene random fittings fixed complete to walls, ceiling, or in floors etc, Including all fitttings, complete all as specified and directed.

M & L Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions, for bore dia of pipe 15 mm, complete all as specified and as directed.

M & L in repair Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions, for bore dia of pipe 20 mm, complete all as specified and as directed.

M & L in repair Angle stop valve of PTMT any colour high pressure screwed for iron pipe, complete all as specified and directed.

M & L in repair Swivel shower Min 125 mm size of PTMT any colour for fixing with 15 mm pipe (minimum weight 40 gm), supplied and fixed in repairs complete all as specified and directed.

S & F in repair CP fancy type Bib taps, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, for bore dia of pipe 15mm, supplied and fixed in repairs complete.

S & F in repair CP Pillar taps fancy type with capstan head, CP, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nut, screwed for iron pipe 15 mm bore, complete all as specified and directed.

S & F in repair, Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20 mm dia (minimum weight 210 gms) complete all as specified and directed.

S & F in repair WHB mixer CP Fancy Type crewed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nut, screwed for iron pipe 15 mm bore, complete all as specified and directed.

S & F Sink Mixer CP Fancy type as per direction by Engg-in-charge fixed in repair compelete all as specified and directed.

S & F wall mixer CP Fancy type as per direction by Engg-in-charge fixed in repair compelete all as specified and directed.

Supply and fix in repair 25mm dia PVC coated decorative mild steel drapery/ curtain rod cut to required size and fixed to brackets as specified and as directed

Supply and fixing in repair 25mm dia PVC coated decorative mild steel drapery/ curtain bracket matching to item no 78 above all as specified and as directed

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames/steel frames glazed with putty or fixed with beads compelete all as specified and directed.

S&F 3mm plain sheet glass ordinary quality and glazing with oil putty or fixed with fillets 2nd class hard wood of sectional area not exc 3 Sqcm and glass not exc 0.5 Sqm each pane complete all as specified and directed.

M & L preparation of new steel surfaces of any description over 10cm in girth or width & applying two coats of synthetic enamel paint over a coat of primer compelete all as specified and directed.

M&L 75 mm in repairs PVC (SWR) floor trap, plain with grating including jointing with solvent cement compelete all as specified and directed.

M&L 75 mm in repairs PVC (SWR) multi floor trap with grating including jointing with solvent cement compelete all as specified and directed.

M&L for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement compelete all as specified and directed.

Taking down PVC pipes including all fittings any size and pattern compelete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors compelete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors compelete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls compelete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls compelete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends any radius compelete all as specified and directed.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc) sheets in roof coverings compelete all as specified and directed.

S & F Pre-painted galvalum aluminium zinc coating steel based corrugated steel sheet 0.50mm thick (total coated thickness) of any colour having tensile strength of 550 Mpa minimum, yield strength, it shall be coated with hot dip alloy of 55% aluminimum, 43.5% zinc,1.5% Silicon and finished with resin coat on both surface @ 150 gm/ Sqm of coating as specified and shall be fixed with hot dip galvanised, self drilling and self tapping screws neoprened and EDPM washers as in roof covering all as directed at site all as specified and dircted.

S&F pre painted galvalume aluminium zinc coating steel based plain steel sheet 0.50 mm thick of any colour having rensile strength of 550 Mpa as in roof/covering/cladding to wall, fixed with self tapping screws all as specified and as directed at site, compelete all as specified and directed.

S & F Joist, channel, angle or tee , square or rectangular, tubler sections, fixed indipendently or as purlin , rafter, or post including cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts , providing and fitting angle cleats, fish plates, gusset plates etc, complete all as specified and directed.(Fe-410-W(Gde-E-250) quality A), compelete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for angle iron pickets or fencing post or any description etc, all as specified and directed.

Dismantling of wall and ceiling boards (fiber, pulp, insulation, etc) or insulation boards /slabs/blankets, any thickness including cover fillets compelete all as specified and directed.

S & F Anodised aluminium snap grid frame work of size 605 x 605 mm for false ceiling securing with 4 mm dia GI wire of 1.20 mtr centre to centre tying to roof members or bolting with self taping screws including all necessar y arrengements complete all as specified and directed.

M & L 600x600x4mm thick HPSC (High Pressure Steam Cured) Oceanic pre-primed self embossed textured designer board water, termite and fire resistant as in ceiling or wall penalling fixed with screws as per manufactur's instructions complete all as specified and directed.

ram prashad chotelal batham

M/S GARG CONSTRUCTION

M/S Ashish Construction

Goyal Construction

sunway associates