Construction of combined operational offices for DGCA, BCAS, AAIB, AERA and AAI at Safdarjung Airport, New Delhi

Amount

HT PANEL 11 KV Seven Panel Switch Gear : 11 KV Seven Panel Switch Gear as desciribed in SOQ Item No. 1 of tender documents.

Battery Charger Design, manufacture, assembly, supply, erection, testing & commissioning of 24V, float cum boost battery charger and necessary distribution board with 10 Nos. 16A outgoing feeders, instrument panel, Amp, Volts meter, interconnections etc., suitable for incoming power supply of 230 V, 1 phase, 50 Hz ± 10%.

Battery Design, manufacture, assembly, supply erection, testing & commissioning of 24 Volt, 180 AH Battery bank of Ni-Cadmium maintenance free batteries, duly charged complete with connecting lead mounting stand etc. as required, suitable for control supply to 11 KV board.

TRANSFORMER (DRY TYPE ) Design, manufacture , supply , assembly at site , installation, testing and commissioning of 2000 KVA Transformer with percentage impedance 6.25% (without negative tolerance) 11 KV / 415 V, 3 phase, 50 Hz delta/star connected, indoor, cast resin, copper wound, Dry type , natural air cooled transformer, with class F insulation complete with all fittings such as OFF Load Tap Changer +5 % to –7.5% tapping at the step of 2.5%, with AVR, RTCC bi-directional roller, diagrams & rating plate & Winding temperature indicator, lifting lugs, termination of 11 KV cable on HT side with top entry and sadwiched bus duct on L T side. Losses of transformer shall be as per ECBC. 2000 KVA Transformer as mentioned above.

MV PANELS Totally Type Tested Assemblies (TTA) Design, manufacture , supply , assembly at site , installation, testing and commissioning of following cubical type panels Totally Type Tested (TTA) made of CRCA sheet, base channel, doors & partitions complete with, Air Circuit Breaker, Moulded Case Circuit Breakers, meters, indicating lamps, current transformer etc. complete in all respects, insulated aluminium bus bars with heat shrinkable PVC sleeve in suitable bus bar chambers, interconnection,bus bar shrouds at joints, wiring, name plate, danger plate, earth bus etc. & comprising of compartments with hinged door for each feeder & its accessories, cable alley with hinged doors, bus chamber with bolted door etc. The panel shall be dust & vermin proof construction with rubber gasket and powder coated . The panel shall be free standing floor mounted type as per relevant drawing. The panel shall be completely modular and compartmentalised with Form 4 B Seperation as per IEC 61439. The panel shall be manufactured as per IEC 61439. Note:- i) All MCCBS shall be with Extended type Front door operating handle, Phase Spreaders & Phase Barriers. ii) Metering CT's burden shall be 15VA & accuracy class 1.0. iii) CT's shall be "CAST RESIN" type . iv) MCCB's up to and including 250 Amp shall be with adjustable thermal-magnetic release for over current and short circuit protection adjustable from 80-100%. MCCB above 250 amp shall be with Microprocessor based release for over current and short circuit protection. All incoming MCCBs above 250 A will be provided additionally with earth falut protection. Bus-coupler MCCB may be without protection. v) All indication lights shall be LED type. vi) All meter shall be "DIGITAL" type. vii) Rated Short time withstand current of all ACB's are Icw for one second. viii) Breaking Capacity of all MCCB's are Ics Service Breaking Capacity ix) Degree of Protection shall be IP:42 .For indoor aplication. x) Panel Manufacturer should have Type Test Certificates for Short Time withstand current test of 50KA for 1.0 Sec from CPRI. Bhopal / Bangalore. xii) "ON" Indicating lamp shall be provided for all 3 phase MCCB out going feeders . xiii) Control SP MCB's of 2A Rating shall be provided for each metering circuit. xiv) 20% spare control terminal to be provided. xv) Live parts shall not be accessible after opening the door, Transparent acrylic sheet to be provided to cover the same & busbar joints section shall be covered with PVC shrouds. xvi) All MFM will have M-Bus conectvity over 485 port for BMS integration. xvii) All EDO breakers shall have spare contacts on the rear of the panel for BMS conectivity. xviii) The panel shall be suitable for BMS Integeration.

DG Sets Isolator Panels:- One (1) Nos. 800A , 50 KA Four pole , EDO ACB, with ON/OFF indication lamp, phase indication lamp and TNC control switch etc. complete as required .

Main MV Panel . Main MV Panel With Gas Flooding as described in SOQ Item No.5.02 of tender document.

MV Panel - Car Charger Panel i. Incomer One (1) Nos. 630 A, 50 KA, TP+N pole MCCB with Microprocessor based release for short circuit, over current and earth fault .The incomer shall be provided with the following. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 630/5A Class 1.0, 15VA. One set ( 3 nos.) Phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp ii. Busbar : 800A , 50kA TP + N Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 50% rated. Separate earth busbar of 32 x 6 mm of GI. shall be provided on the rear bottom of the panel. iii. Outgoings : Six (6) Nos. 63 A, 25 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . Fourteen (14) Nos. 63 A, 16 kA, DP MCB MV Panel -Car Charger Panel as described above.

MV Panel - Main AHU Panel Main AHU Panel with Gas flooding as described in SOQ Item No. 5.04 of tender document.

MV Panel - Basement -1 Ventilation Panel-1 i. Incomer One (1) Nos. 630 A, 50 kA, TP+N , MCCB with Microprocessor based release for short circuit, over current and earth fault .The incomer shall be provided with the following. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 630/5A Class 1.0, 15VA. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp ii. Busbar : 800 A , 50kA TP + N Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 50% rated. Separate earth busbar of 32 x 3 mm of GI. shall be provided on the rear bottom of the panel. iii. Outgoings : Ten ( 10) Nos. 100A, 35 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . Six (6) Nos. 63A, 25 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . Five ( 5 ) Nos. 16 A, 10 kA, TP + N MCB MV Panel - Basement -1 Ventilation Panel-1 as describd above

MV Panel - Basement -1 Ventilation Panel-2 i. Incomer One (1) Nos. 630A, 50 kA, TP+N , MCCB with Microprocessor based release for short circuit, over current and earth fault .The incomer shall be provided with the following. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 630/5A Class 1.0, 15VA. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp ii. Busbar : 800 A , 50kA TP + N Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 50% rated. Separate earth busbar of 32 x 3 mm of GI. provided on the rear bottom of the panel. iii. Outgoings : Three( 3) Nos. 200A, 35 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . Seven( 7) Nos. 100A, 35 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . Three ( 3 ) Nos. 63A, 25 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . Three ( 3 ) Nos. 16 A, 10 kA, TP + N MCB MV Panel - Basement -1 Ventilation Panel-2 as describd above

MV Panel - Basement -2 Ventilation Panel i. Incomer One (1) Nos. 630A, 50 kA, TP+N , MCCB with Microprocessor based release for short circuit, over current and earth fault .The incomer shall be provided with the following. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 630/5A Class 1.0, 15VA. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp ii. Busbar : 800 A , 50kA TP + N Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 50% rated. Separate earth busbar of 32 x 3 mm of GI. shall be provided on the rear bottom of the panel. iii. Outgoings : Fourteen ( 14) Nos. 100A, 35 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . Two ( 2 ) Nos. 63A, 25 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . Two ( 2 ) Nos. 16 A, 10 kA, TP + N MCB MV Panel - Basement -2 Ventilation Panel as describd above

MV Panel - Smoke Extraction and Pressurisation Panel at Terrace i. Incomer One (1) Nos. 630A, 50 kA, TP+N , MCCB with Microprocessor based release for short circuit, over current and earth fault The incomer shall be provided with the following. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 630/5A Class 1.0, 15VA. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp ii. Busbar : 800 A , 50kA TP + N Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 50% rated. Separate earth busbar of 32 x 3 mm of GI. shall be provided on the rear bottom of the panel. iii. Outgoings : Eight ( 8 ) Nos.100 A, 35 kA, TP + N MCCB with continuous variable thermal magnetic release for short circuit, over current protection . Two ( 2 ) Nos. 63 A, 25 kA, TP + N MCCB with continuous variable thermal magnetic release for short circuit, over current protection . Four( 4 ) Nos. 40 A, 10 kA, TP + N MCB Eight ( 8 ) Nos. 32 A, 10 kA, TP + N MCB Two ( 2 ) Nos. 25 A, 10 kA, TP + N MCB Six (6) Nos 16 A,10 KA TP+N MCB MV Panel - Smoke Extraction and Pressurisation Panel at Terrace as describd above

MV Panel - Main Lift Panel ( At terrace) i. Incomer Two (2) Nos. 400A, 50 kA, Four pole, MCCB with Microprocessor based release for short circuit, over current and earth fault .Each incomer shall be provided with the following. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 400/5A Class 1.0, 15VA. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp ii. Busbar : 500 A , 50 kA TP + N Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 50% rated. Separate earth busbar of 32 x 3 mm of GI. shall be provided on the rear bottom of the panel. iii. Bus Coupler : One (1) No. 400A, 50 KA, Four pole, MCCB with ON/OFF indication. iv. Outgoings : Section- I: Two ( 2 ) Nos. 250A, 35 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . Five ( 5 ) Nos. 100A, 35 kA, TP + N MCCB with continuous variable thermal magnetic release for short circuit, over current protection . Section- II: One ( 1 ) Nos. 250A, 35 kA, TP + N MCCB with continuous variable thermal magnetic release for short circuit, over current protection . Six ( 6 ) Nos. 100A, 35 kA, TP + N MCCB with continuous variable thermal magnetic release for short circuit, over current protection . Note:-Mechanical interlocking will be provided in incomings and bus-coupler. Main Lift Panel as described above.

MV Panel - Basement , LGF ( Non Tower ) Lighting & Power Panel i. Incomer Two (2) Nos. 400A, 50 kA, Four pole, MCCB with Microprocessor based release for short circuit, over current and earth fault .Each incomer shall be provided with the following. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 400/5A Class 1.0, 15VA. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp ii. Busbar : 500A , 50kA, TP+N , Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 100% rated. Separate earth busbar of 25 x 3 mm of GI. shall be provided on the rear bottom of the panel. iii. Bus Coupler : One (1) No. 400A, 50 KA, Four pole, MCCB with ON/OFF indication. iv. Outgoings : Section- I: Six ( 6) Nos. 100A, 35 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . Section- II: Six ( 6) Nos. 100A, 35 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . Note:-Mechanical interlocking will be provided in incomings and bus-coupler. MV Panel - Basement , LGF ( Non Tower ) Lighting & Power Panel as described above.

MV PANELS ( Partially Type Tested Assemblies) (PTTA) Main MV Panels as described in SOQ Item No.6 of tender document.

Hybrid APFC Panels (600 kVAR) ( Partially Type Tested Panel) ( PTTA) Hybrid APFC Panels (600 kVAR) as described in SOQ Item No. 6.01 of tender Document.

MV Panel - Ground Floor Smoke Extraction Panel i. Incomer One (1) Nos. 63A, 35 kA, TP+N, MCCB with variable thermal magnetic release for short circuit, over current and earth fault . Incomer shall be provided with the following. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 63/5A Class 1.0, 15VA. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp ii. Busbar : 100 A , 35kA, Four Pole , Al. Busbar insulated with heat shrinkable sleeves and shall be color coded. The neutral busbar shall be 100% rated. Separate earth busbar of 25 x 3 mm of GI. shall be provided on the rear bottom of the panel. iii. Outgoings : Two ( 2 ) Nos. 25 A, 10 kA, TP + N MCB with Two (2) Nos 16 A,10 KA TP+N MCB MV Panel - Ground Floor Smoke Extraction Panel as described above

MV Panel - LGF Ventilation Panel i. Incomer Two (2) Nos. 200 A, 35 kA, Four pole, MCCB with variable thermal magnetic release for short circuit, over current and earth fault .Each incomer shall be provided with the following. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 200/5A Class 1.0, 15VA. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp ii. Busbar : 250 A , 35 kA TP + N Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 50% rated. Separate earth busbar of 32 x 3 mm of GI. shall be provided on the rear bottom of the panel. iii. Bus Coupler : One (1) No. 200A, 35 KA, Four pole, MCCB with ON/OFF indication. iv. Outgoings : Section- I: Two( 2 ) Nos. 63A, 25 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . One ( 1 ) Nos.40 A, 10 kA, TP + N MCB Four ( 4 ) Nos. 32A, 10 kA, TP + N MCB . One ( 1 ) Nos. 25 A, 10 kA, TP + N MCB One (1) Nos 16 A,10 KA TP+N MCB Section- II: One ( 1 ) Nos. 63A, 25 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . Two ( 2 ) Nos.40 A, 10 kA, TP + N MCB . Four ( 4 ) Nos. 32A, 10 kA, TP + N MCB One ( 1 ) Nos. 25 A, 10 kA, TP + N MCB One (1) Nos 16 A,10 KA TP+N MCB Note:-Mechanical interlocking will be provided in incomings and bus-coupler. MV Panel - LGF Ventilation Panel as describd above

MV Panel - Water Supply Panel i. Incomer Two (2) Nos. 250 A, 35 kA, Four pole, MCCB with variable thermal magnetic release for short circuit, over current and earth fault . Each incomer shall be provided with the following. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 250/5A Class 1.0, 15VA. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp ii. Busbar : 315A , 35kA, TP+N, Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 50% rated. Separate earth busbar of 25 x 3 mm of GI. shall be provided on the rear bottom of the panel. iii. Bus Coupler : One (1) No. 250A, 35 KA, Four pole, MCCB with ON/OFF indication. iv. Outgoings : Section- I: One ( 1 ) Nos. 160A, 35 kA, TP + N MCCB with continuous variable thermal magnetic release for short circuit, over current protection . Three ( 3 ) Nos. 63A, 25 kA, TP + N MCCB with continuous variable thermal magnetic release for short circuit, over current protection . Section- II: Two ( 2 ) Nos. 100A, 35 kA, TP + N MCCB with continuous variable thermal magnetic for short circuit, over current protection . Two ( 2 ) Nos. 63A, 25 kA, TP + N MCCB with continuous variable thermal magnetic for short circuit, over current protection . Note:-Mechanical interlocking will be provided in incomings and bus-coupler. Water Supply Panel as described above.

MV Panel - Sump Pump Panel Incomer Two (2) Nos. 63A, 35 kA, Four pole, MCCB with continuous variable thermal magnetic release for short circuit, over current and earth fault . Each incomer shall be provided with the following. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 63/5A Class 1.0, 15VA. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp i. Busbar : 100 A , 35kA, Four Pole , Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 100% rated. Separate earth busbar of 25 x 3 mm of GI. shall be provided on the rear bottom of the panel. ii. Bus Coupler : One (1) No. 63A, 35 KA, Four pole, MCCB with ON/OFF indication. iii. Outgoings : Section- I: Seven ( 7 ) Nos. 16A, 10 kA, TP + N MCB Section- II: Seven ( 7 ) Nos. 16A, 10 kA, TP + N MCB Note:-Mechanical interlocking will be provided in incomings and bus-coupler. Sump Pump, Panel as described above.

MV Panel - DG Auxiliary Panel ( OUT DOOR NEAR DG SETS ) i. Incomer Four pole, Automatic ON LOAD Change Over Switch of 200 A with ON/OFF indicating lamps,complying to Standard IEC 60947-6-1 for transfer and 60947-3 for disconnection function.It shall have three distinct stable positions .The ATS shall have all the four poles fully rated. One (1) Nos. 200A, 50 kA, TP+N , MCCB with continuous variable thermal magnetic for short circuit, over current and earth fault .incomer shall be provided with the following. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 200/5A Class 1.0, 15VA. ii. Busbar : 250 A , 50 kA, TP+N, Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 50% rated. Separate earth busbar of 25 x 3 mm of GI. shall be provided on the rear bottom of the panel. iii. Outgoings : Seven ( 7 ) Nos. 63A, 25 kA, TP + N MCCB with continuous variable thermal magnetic release for short circuit, over current protection . DG Auxiliary Panel Panel as described above.

MV Panel - External Lighting Panel i. Incomer One (1) Nos. 200 A, 35 kA, TP+N , MCCB with continuous variable thermal magnetic release for short circuit, over current and earth fault . Incomer shall be provided with the following. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 200/5A Class 1.0, 15VA. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp ii. Busbar : 250A , 35kA, TP+N , Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 50% rated. Separate earth busbar of 25 x 3 mm of GI. shall be provided on the rear bottom of the panel. iii. Outgoings : Six ( 6 ) Nos. 63A, 25 kA, TP + N MCCB with continuous variable thermal magnetic release for short circuit, over current protection . External Lighting Panel as described above.

MV Panel - Basement 1&2 Lighting & Power Panel i. Incomer Two (2) Nos. 100A, 35 kA, Four pole, MCCB with variable thermal magnetic release for short circuit, over current and earth fault . Each Incomer shall be provided with the following. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 100/5A Class 1.0, 15VA. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp ii. Busbar : 160A , 35kA, TP+N , Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 100% rated. Separate earth busbar of 25 x 3 mm of GI. shall be provided on the rear bottom of the panel. iii. Bus Coupler : One (1) No. 100A, 35 KA, Four pole, MCCB with ON/OFF indication. iv. Outgoings : Section- I: Two ( 2) Nos.63A, 25 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . Four ( 4 ) Nos. 32A, 10 kA, TP + N MCB Three( 3) Nos. 32A, 10 kA, SP MCB Section- II: Two ( 2) Nos.63A, 25 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . Four ( 4 ) Nos. 32A, 10 kA, TP + N MCB Three ( 3) Nos. 32A, 10 kA, SP MCB Note:-Mechanical interlocking will be provided in incomings and bus-coupler. MV Panel - Basement 1&2 Lighting & Power Panel as described above.

MV Panel - ESS, AC PLANT, PUMP ROOM AND LGF ( NON-TOWER ) Lighting & Power Panel i. Incomer Two (2) Nos. 100 A, 35 kA, Four pole, MCCB with continuous variable thermal magnetic release for short circuit, over current and earth fault . Each Incomer shall be provided with the following. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 100 /5A Class 1.0, 15VA. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp ii. Busbar : 160A , 35kA, Four Pole , Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 100% rated. Separate earth busbar of 25 x 3 mm of GI. shall be provided on the rear bottom of the panel. iii. Bus Coupler : One (1) No. 100 A, 35 KA, Four pole, MCCB with ON/OFF indication. iv. Outgoings : Section- I: Two( 2) Nos.63A, 25 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . Two ( 2 ) Nos. 32A, 10 kA, TP + N MCB Three ( 3 ) Nos. 32A, 10 kA, S P MCB Section- II: Two( 2) Nos.63A, 25 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . Two ( 2 ) Nos. 32A, 10 kA, TP + N MCB Three ( 3 ) Nos. 32A, 10 kA, S P MCB Note:-Mechanical interlocking will be provided in incomings and bus-coupler. MV Panel - ESS, AC PLANT, PUMP ROOM AND LGF ( NON-TOWER ) Lighting & Power Panel as described above.

MV Panel - Terrace HVAC Panel i. Incomer One (1) Nos. 200A, 35 kA, TP+N , MCCB with continuous variable thermal magnetic release for short circuit, over current and earth fault . Incomer shall be provided with the following. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 200/5A Class 1.0, 15VA. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp ii. Busbar : 250A , 35kA, TP+N , Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 50% rated. Separate earth busbar of 25 x 3 mm of GI. shall be provided on the rear bottom of the panel. iii. Outgoings : Six ( 6 ) Nos. 63A, 25 kA, TP + N MCCB with continuous variable thermal magnetic release for short circuit, over current protection . Two ( 2 ) Nos. 32 A, 10 kA, TP + N MCB Six ( 6 ) Nos. 10 A, 10 kA, TP+N MCB Terrace HVAC Panel as described above.

MV Panel - AHU Floor Panel -I i. Incomer One (1) Nos. 63A, 25 kA, TP+N, MCCB with variable thermal magnetic release for short circuit, over current and earth fault . Incomer shall be provided with the following. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 63/5A Class 1.0, 15VA. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp ii. Busbar : 100 A , 35kA, Four Pole , Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 100% rated. Separate earth busbar of 25 x 3 mm of GI. shall be provided on the rear bottom of the panel. iii. Outgoings : Two ( 2 ) Nos. 32 A, 10 kA, TP + N MCB Two (2) Nos 16 A,10 KA TP+N MCB Three (3) Nos 10 A,10 KA SP+N MCB MV Panel - AHU Floor Panel- I as described above

MV Panel - AHU Floor Panel -II i. Incomer One (1) Nos. 100 A, 25 kA, TP+N, MCCB with variable thermal magnetic release for short circuit, over current and earth fault . Incomer shall be provided with the following. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 100/5A Class 1.0, 15VA. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp ii. Busbar : 160 A , 35kA, Four Pole , Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 100% rated. Separate earth busbar of 25 x 3 mm of GI. shall be provided on the rear bottom of the panel. iii. Out going:- Three ( 3 ) Nos. 32 A, 10 kA, TP + N MCB Four (4) Nos 16 A,10 KA TP+N MCB Four (4) Nos 10 A,10 KA TP+N MCB Three (3) Nos 10 A,10 KA SP+N MCB MV Panel - AHU Floor Panel -II as described above

MV Panel - Lab Panel Basement I&II i. Incomer One (1) Nos. 100 A, 35 kA, TP+N, MCCB with variable thermal magnetic release for short circuit, over current and earth fault . Incomer shall be provided with the following. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 100/5A Class 1.0, 15VA. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp ii. Busbar : 160 A , 35kA, Four Pole , Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 100% rated. Separate earth busbar of 25 x 3 mm of GI. shall be provided on the rear bottom of the panel. iii. Out goimg:- Four ( 4 ) Nos. 63 A, 25 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . Four ( 4 ) Nos. 32 A, 10 kA, TP + N MCB MV Panel - Lab Panel Basement-I&II as described above

MV Panel - Kitchen & Cafeteria Panel i. Incomer One (1) Nos. 250 A, 35 kA, TP+N, MCCB with variable thermal magnetic release for short circuit, over current and earth fault . Incomer shall be provided with the following. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 250/5A Class 1.0, 15VA. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp ii. Busbar : 315 A , 35kA, TP+N , Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 50% rated. Separate earth busbar of 25 x 3 mm of GI. shall be provided on the rear bottom of the panel. iii. Out goimg:- Four ( 4 ) Nos. 63 A, 25 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . Four ( 4 ) Nos. 32 A, 10 kA, TP + N MCB Four (4) Nos 16 A,10 KA TP+N MCB Four (4) Nos 32 A,10 KA DP MCB Four (4) Nos 16 A,10 KA DP MCB MV Panel - Kitchen & Cafeteria as described above

Data Centre UPS Panel i. Incomer Two (2) Nos. 200A, 35 kA, Four Pole, MCCB with variable thermal magnetic release for short circuit, over current and earth fault . Incomer shall be provided with the following. One (1) no. 4P 200A Automatic Transfer Switch (ATS), complying to Standard IEC 60947-6-1 for transfer and 60947-3 for disconnection function.It shall have three distinct stable positions .The ATS shall have all the four poles fully rated. One (1) No. Multi Function Meter with one set (3 Nos.) of CTs of ratio 400/5A Class 1.0, 15VA. One set ( 3 nos.) phase indication lamps with control MCB. One set ( 3 nos.) ON/OFF/TRIP indication lamp ii. Busbar : 250 A , 50 kA TP + N Al. Busbar insulated with heat shrinkable sleeves and shall be colour coded. The neutral busbar shall be 50% rated. Separate earth busbar of 25 x 3 mm of GI. shall be provided on the rear bottom of the panel. iii. Outgoings : Four (4) Nos. 100A, 35 kA, TP + N MCCB with continuous variable thermal magnetic release for short circuit, over current protection . Three (3) Nos. 63A, 25 kA, TP + N MCCB with variable thermal magnetic release for short circuit, over current protection . MV Panel - Data Centre UPS Panel described as above

BUS TRUNKING : SANDWICH TYPE IP:54 Supplying, installing by suspension on ceiling/along the wall, testing and commissioning of following capacity Sandwich Type Bus-Trunking for use on 3 phase 4 wire 415 V, 50Hz A.C. supply with metal clad enclosure having IP-54 rating after fixing all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos. aluminium bus bars having current density of 130 A/ sq. cm at nominal current rating, necessary joints, elbow joints & expansion joints and bends, phase transposition unit , adopter box and copper flexible for joints at both the ends, continuous earthing with 2 Nos. aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required

400 amps 25KA SC for 1 sec

630 amps 50KA SC for 1 sec

800 amps 50KA SC for 1 sec

1000 amps 50KA SC for 1 sec

1250 amps 50KA SC for 1 sec

1600 amps 50KA SC for 1 sec

3200 amps 50KA SC for 1 sec

Supplying, Installation, of GI Canopy for protection of Bus trunking for oudoor installation.at terrace as required.

RISING MAIN (SANDWICH TYPE ) : Supplying, installing by suspension on ceiling/along the wall, testing and commissioning of following capacity Sandwich Type Rising Mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal clad enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos aluminium bus bars having current density of 130 A/ sq cm at nominal current rating, necessary joints, elbow joints & expansion joints and bends, fire barrier at each floor, provision of tapping at every metre, adopter box and copper flexible for joints, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required

400 amps 50KA SC for 1 sec

630 amps 50KA SC for 1 sec

Supplying, installation, testing & commisioning of following capacity End Feed Unit for the existing sandwich Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required

200 amps 15KA SC for 1 sec

315 amps 25KA SC for 1 sec

630 amps 50KA SC for 1 sec

Supplying, installation, testing & commisioning of following capacity Plug In/ tap off box on the existing sandwich Type bus trunking/ rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick sheet steel enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete etc. as required

125 amps 15KA SC for 1 sec

200 amps 25KA SC for 1 sec

Providing and fixing following rating and breaking capacity and pole MCCB in existing tap off boxes / end feed units of sandwich type rising mains including drilling holes in cubicle panel, making connections, etc. as required.

63 Amp, 30 KA,FPMCCB

100Amp,30KA,FPMCCB

200Amp,36KA,FPMCCB

315 Amp 50 KA FP MCCB

630 Amp 50 KA,FP MCCB

HT CABLES Supply of following sizes of 11 KV(UE) Aluminium conductor XLPE insulated , galvanised flat steel strip Armoured , inner and outer sheath of FRLS PVC cable as per IS 7098 Part -II with latest amendment and as per other relevant standards and tender specification

3 x 185 Sq mm

3 x 240 Sq mm

LT CABLES Supply of 1100 Volts grade, of following sizes of Aluminium conductor XLPE insulated , galvanised flat steel strip / wire Armoured , inner and outer sheath of FRLS PVC cable as per IS 7098 Part -I with latest amendment and as per other relevant standards and tender specification

4 X 25 sq. mm

3½ X 50 sq. mm

3½ X 95 sq. mm

3½ X 150 sq. mm

3½ X 240 sq. mm

3½ X 300 sq. mm

LT Cable Copper Conductor Supply of 1100 Volts grade, of following sizes of Copper conductor XLPE insulated , galvanised flat steel strip / wire Armoured , inner and outer sheath of FRLS PVC cable as per IS 7098 Part -I with latest amendment and as per other relevant standards and tender specification

2x6 Sq mm

2x10 Sq mm

2x16 Sq mm

3x6 Sq mm

3x10 Sq mm

3x16 Sq mm

4x6 Sq mm

4x10 Sq mm

4x16 Sq mm

LT Cable Fire Survival Copper Conductor Supplying of 1100 Volts grade of following sizes of Copper conductor Fire Survival cable with Glass Mica & Ethylene Propylene Rubber insulation Low smoke halogen free sheathing , galvanised flat steel strip / wire Armoured as per IEC-60502-1:2004, BS:7846:2009 and other intrnational & British standards and as per tender specifications as required.

2x4 Sq mm

2x6 Sq mm

2x10 Sq mm

2x16 Sq mm

3x6 Sq mm

3x10 Sq mm

3x16 Sq mm

4x6 Sq mm

4x10 Sq mm

4x16 Sq mm

4 X 25 sq. mm

3½ X 35 sq. mm

3½ X 50 sq. mm

3½ X 95 sq. mm

Ladder Type Cable Trays Supply & installation of prefabricated hot dip galvanized steel ladder type cable trays, (galvanisation not less than 50 microns) including bends,tees & reducers fabricated out of hot rolled sheet steel with rigid welded construction with a rung as per standard and specifications, of approved make and cable tray fittings, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-charge.

1500 mm wide ( Runners 25 x 100 x 25 x 3 mm and Rungs 20 x 40 x 20 x 3 mm 250 mm centre to center.)

1200 mm wide ( Runners 25 x 100 x 25 x 3 mm and Rungs 20 x 40 x 20 x 3 mm 250 mm centre to center.)

750 mm wide ( Runners 20 x 75 x 20 x 2.5 mm and Rungs 20 x 30 x 20 x 2.5 mm 250 mm centre to center.)

600 mm wide ( Runners 20 x 75 x 20 x 2 .5 mm and Rungs 20 x 30 x 20 x 2.5 mm 250 mm centre to center.)

Perforated Type Cable Trays (Hot Dipped Galvanized Iron Cable Tray) Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

100 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 75 mm depth X 2.0 mm thickness

750 mm width X 75 mm depth X 2.0 mm thickness

900 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “bends” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required

100 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 75 mm depth X 2.0 mm thickness

750 mm width X 75 mm depth X 2.0 mm thickness

900 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Tee” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

100 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 75 mm depth X 2.0 mm thickness

750 mm width X 75 mm depth X 2.0 mm thickness

900 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Cross member” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

100 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 75 mm depth X 2.0 mm thickness

750 mm width X 75 mm depth X 2.0 mm thickness

900 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Reducer” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

100 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 75 mm depth X 2.0 mm thickness

750 mm width X 75 mm depth X 2.0 mm thickness

900 mm width X 75 mm depth X 2.0 mm thickness

Perforated Type Cable Trays (Stain less steel (SS-304) Cable Tray) Supplying and installing following size of perforated Stain less steel (SS-304) cable tray with perforation not more than 17.5%, in convenient sections, joined with SS-304 connectors, mounted on masonary support 45 CM above floor level at interval as per specifications . All fastners will be of GI and all other accessories will be that of SS-304. etc. as required.

100 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 75 mm depth X 2.0 mm thickness

900 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Stain less steel (SS-304) cable tray “bends” with perforation not more than 17.5%, in convenient sections, joined with SS-304 connectors, mounted on masonary support 45 CM above floor level at interval as per specifications . All fastners will be of GI and all other accessories will be that of SS-304. etc. as required.

100 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 75 mm depth X 2.0 mm thickness

900 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Stain less steel (SS-304) cable tray “Tee” with perforation not more than 17.5%, in convenient sections, joined with SS-304 connectors, mounted on masonary support 45 CM above floor level at interval as per specifications . All fastners will be of GI and all other accessories will be that of SS-304. etc. as required.

100 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 75 mm depth X 2.0 mm thickness

900 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Stain less steel (SS-304) Iron cable tray “Cross member” with perforation not more than 17.5%, in convenient sections, joined with SS-304 connectors, mounted on masonary support 45 CM above floor level at interval as per specifications . All fastners will be of GI and all other accessories will be that of SS-304. etc. as required.

100 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 75 mm depth X 2.0 mm thickness

900 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Stain less steel (SS-304) Iron cable tray “Reducer” with perforation not more than 17.5%, in convenient sections, joined with SS-304 connectors, mounted on masonary support 45 CM above floor level at interval as per specifications . All fastners will be of GI and all other accessories will be that of SS-304. etc. as required.

100 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

600 mm width X 75 mm depth X 2.0 mm thickness

900 mm width X 75 mm depth X 2.0 mm thickness

HT CABLES LAYING Laying of one number XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Above 120 sq. mm and upto 400 sq. mm

Laying of one number additional XLPE power cable of 11 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Above 120 sq. mm and upto 400 sq. mm

Laying of one number XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

Above 120 sq. mm and upto 400 sq. mm

Laying of one number XLPE power cable of 11 KV grade of following size in the existing cable tray as required.

Above 120 sq. mm and upto 400 sq. mm

MV CABLES LAYING Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.

Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Supplying and making cable route marker with cement concrete1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required.

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required

HT CABLES JOINTING & END TERMINATION Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :

Supplying and making straight through cable jointing with heat shrinkable jointing kit complete with all accessories including ferrules suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :

CABLES END TERMINATION (MV ALUMINIUM CABLES END TERMINATION) Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

4 X 25 sq. mm

3½ X 50 sq. mm

3½ X 95 sq. mm

3½ X 150 sq. mm

3½ X 240 sq. mm

3½ X 300 sq. mm

CABLES END TERMINATION (MV COPPER CABLE END TERMINATION) Supplying and making end termination with brass compression gland and Copper lugs for following size of PVC insulated and PVC sheathed / XLPE Copper conductor cable of 1.1 KV grade as required.

2x6 Sq mm

2x10 Sq mm

2x16 Sq mm

3x6 Sq mm

3x10 Sq mm

3x16 Sq mm

4x6 Sq mm

4x10 Sq mm

4x16 Sq mm

EARTHING

Earthing with G.I. earth pipe 4.5 Meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 Meter below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 Meter below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 Meter below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

SAFETY ITEMS

Supplying and fixing of standard shock restoration chart in heavy wooden frame with 3mm thick plain glass as per specifications of this tender and directions of Engineer-in-Charge.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red Colour on front side as required as per specifications of this tender and directions of Engineer-in-Charge.

Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red Colour on front side as required as per specifications of this tender and directions of Engineer-in-Charge.

Supplying and fixing of 1.1 KV grade nominal 2.0 mm +/- 10% thick insulated Synthetic Mat conforming to IS 15652: 2006 and meeting the requirements of IS 5216 (Part1,2&3), IS 8437, IEC-479 Pub-1, along-with suitable adhesive/ chemibound, Pu resin, waterproofing compound and sealing material as per in service recommendation as per specifications of this tender and directions of Engineer-in-Charge.

Supplying and fixing of 11 KV grade nominal 2.5 mm +/- 10% thick insulated Synthetic Mat conforming to IS 15652: 2006 and meeting the requirements of IS 5216 (Part1,2&3), IS 8437, IEC-479 Pub-1, along-with suitable adhesive/ chemibound, Pu resin, waterproofing compound and sealing material as per in service recommendation as per specifications of this tender and directions of Engineer-in-Charge.

Supply and fixing safety instruction chart in word duly framed with 5mm thick glass required as per specifications of this tender and directions of Engineer-in-Charge.

Supply of Rubber hand gloves suitable for 11 KV as per specifications of this tender and directions of Engineer-in-Charge.

Providing & fixing of set of 4 Nos 9.0 Litre capacity GI bucket painted in post office red Colour with prior coat of red - oxide paint and written with white paint 'Fire' and mounted on MS angle iron frame with bracket of appropriate size and capacity including filling sand etc as per specifications of this tender and directions of Engineer-in-Charge.

Supply of First Aid box as approved by St. John Ambulance Brigade / Indian red Cross conforming to IS 2217 -1963 as per specifications of this tender and directions of Engineer-in-Charge.

MISC CIVIL ITEMS

Making bore of suitable dia for laying of 160 mm DWC HDPE ppe by trench less technilogy at a depth of 1.2 m below ground level from Gate No 3 to the proposed meter room of NDMC in Safdarjung Airport compound including all related works compleet as required .

Excavation for cable trenches of depth upto 1.2 m in soft soil including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 metres.

Filling available excavated earth (excluding rock) in trenches, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 metres.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 160 mm dia (OD-160 mm & ID-135 mm nominal)

Providing and laying in position cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of MACHINERY etc including form work etc as required.

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 150 mm dia

Providing, laying and fixing following dia G.I. pipe (medium class) in ground / on surfac with clamps complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required 150 mm dia

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 120x90 cm and 120 cm deep with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 complete with excavation, refilling the excavated earth and disposal of surplus earth etc as requred.

Fire Curtains Supply, Installation, Testing & Commisioning of Fire Curtains with galvanized MS head box, size (200X200mm) powder coated, side guides size (53x100mm) along with adjustment channels & bottom bars with motors for power up operation with standard battery backup & operated system safe fixed into steel rollers with woven glass fibre fabric, reinforced with stainless steel wire having micronized aluminium polymer coating on each side of the fabric (silver/grey) with the necessary control panel & all installation assemblies & accessories required to complete the installation. The operation shall be suitable for dedicated 240 Volts UPS, 50 Hz AC supply. Complete system shall be tested in accordance with EN 1634-1 (for 120 minutes Integrity & tested at 1000°C) BS 476-22.8 and BS 7346-3. It shall includey Emergency Retract Switch on both sides of the curtain along with necessary control panel Vendor/Manufacturer to submit valid Test Report for the complete systems and not just for fabric from an independent international accredited laboratory. The Test Report of complete system should not be more than 5 years old. Vendor/Supplier should duly submit current dated authorization letter from the manufacturer or principal that he is representing, complete as required. Fire Curtains of following sizes:

Automatic Fire curtains-4295mm (W) X 3500mm (H) ( Nominal Size)

Automatic Fire curtains-4295mm (W) X 3200mm (H) ( Nominal Size)

Automatic Fire curtains-3500mm (W) X 3200mm (H) ( Nominal Size)

D.G. Set - Radiator Cooled (Silent Type ) AT 11 KV DG Set Rating as follows: 2000 KVA ( Prime Power) Radiator Cooled, 11 KV DG Set with Acoustic enclosure as desciribed in SOQ Item No. 50 of tender documents.

Supplying, Shifting, installation, testing and commissioning of NGR & NIS Panels suitable for 3 x 2000 KVA DG Sets at 11 KV complete in all respect . The DG Sets shall work in parralel or independent or in combinartion as per Schematic. The NGR & NIS Panels will have to be designed accordingly.

D.G. Set - Radiator Cooled (Silent Type ) DG Set Rating as follows: 500 KVA ( Prime Power) Radiator Cooled DG Set with Acoustic enclosure as desciribed in SOQ Item No. 52 of tender documents.

11 KV VCB Panel Swith Gear : 11 KV Incomers cum outgoing Panel as desciribed in SOQ Item No. 53 of tender documents.

11 KV Two Panel as Automatic Source Changeover Panel. i) Incomers cum outgoing :- Two ( 2) 11 KV 630 Amps. 350 MVA Electrical operated draw out type Vacuum circuit breaker complete with trip free spring charged closing mechanism, necessary auxiliary relays, control switches, emergency hand trip devices and mechanical ON / OFF indicator etc. Each incoming panel will consist of the following meters/ relays etc.. One (1) Set 11KV/√3 /110/√3, 200VA, Class 1.0, Cast Resin PT with control MCB. One (1) Set of Phase indication lamps with 2Amp SP MCB for protection (Red, Yellow and Blue). One (1) set of Red/ Green indicating lamp for close and open position. One (1) No. Amber indicating lamp for trip indication. One (1) No. Clear indicating lamp for trip circuit healthy. One (1) Blue indicating lamp for spring charged. ii) Busbar : 630 Amp. Color coded heat shrinkable PVC sleeved TP Copper Busbar of 350MVA fault rating. Separate earth busbar of 50 x 6 mm GI shall be provided on the rear bottom of the panel. Note:- Out of Two Incomers only one will be ON at a time and changeover will be automatic on the feeder having supply . 11 KV Two Panel as Automatic Source Changeover Panel as described above.

Auto Starting , Auto Synchronizing , Auto load sharing and load managing 11 KV panel for 3 x 2000 KVA ( Prime Power ) 11 KV DG Sets. Auto Starting , Auto Synchronizing , Auto load sharing and load managing panel as desciribed in SOQ Item No. 55 of tender documents.

Exhaust Piping : Supply, installation, testing and commissioning of exhaust pipe from DG Sets on MS support along the building as per drawing fabricated out of MS pipe including all MS support, fixing accessories and hardwares. The exhaust pipes shall be insulated with 75 mm thick LRB Rock wool density 96 kg per meter cube insulation wrapped in chicken mesh and clad with 24 gauge aluminium sheet as required. The pipes will be extended 6 meters above the top level of building as per CPCB norms. MS support shall be paid seperately . Note: The Contractor shall furnish calculation for exhaust piping sizing for approval by AAI. The system shall meet the performance of the engine without exceeding the back pressure limit prescribed by engine supplier.

500 mm dia 6 mm thick as per IS:3589

300 mm dia 6 mm thick as per IS:3589

Supply, installation, testing and commissioning of SS expansion bellows in exhaust pipe in vertical / horizontal formation as per manufacturer's recommendation complete as required.

500 mm dia

300 mm dia

M.S. Structural Support Design, supplying, erection of self supporting structure along the building, across the driveway as per drawing suitable for supporting exhaust pipes of 3 No 2000 + 1 x 500 KVA DG Sets up to 6 meters above the top level of the building as required as per CPCB Norms. This structure shall be complete with Aviation light with battery & battery charger and earthing , lightning arrestor, including Guy wire supports. This structure shall be designed for a wind velocity prevailing at site, Including welding, cutting, 2 layers of anti-coarrosive primer with 2 layers of silver paint etc. complete as required. The bidder shall workout & furnish the detail for approval in their proposal by AAI. RCC foundation will be provided as per approved structural drawing seperately . This work shall be executed as per darwing.

HSD STORAGE AND SUPPLY SYSTEM : UG Tank Supply, installation, testing & commissioning of HSD storage tank of 20 KL capacity each made out of 6 mm thick shell & 8 mm thick dished shell ,as per IS-1087 and approved for construction, shop drawings duly approved by “CCOE” suitable for under ground installation including the following: Inlet and outlet connections a) Vent pipe. b) Dip pipe assembly with calibration chart c) 550 mm dia manhole with cover. d) Lifting lugs e) MS ladder f) Providing Anti corrosive Pypcoat (AW4) treatment. g) Provision for level sensor (BMS) h) Earthing of HSD Tank with 2 No GI Plate earth electrodes with salt and charcoal etc. i) Suitable RCC foundation including excavation, sand filling, brick masonary work disposal of surplu earth etc complete as required. j) Supplying and fixing fire extingushers and sand buckets as required as per rules. k) Chain link fensing around the tank with provision of gate. UG Tanks as described above NOTE:- Before execution of above item of 20 KL HSD UG Tank, the contractor will examine the feasibility at site and in case it is found that it is not possibel to execute this item the item will be deleted. No payment will be made for carryiong out feasibility study.

Fuel Pumps Supply, installation, testing & commissioning of electrical driven rotary gear pumps suitable for pumping of HSD consisting of following : a) Horizontally mounted single stage capable of delivering 35 LPM at 20 Mtr. Head while running at required 1440 RPM, complete with proper connection to suction and delivery line, bypass arrangement against over pressure. b) Flame proof motor for fire protection pumping unit suitable for 415 + 10% V, 3 phase, 50 Hz AC supply and of suitable HP for the above pumps. c) Flame proof ON/ OFF push button station suitable for above motor including connection and inter connection with starters’s installed in MCC. d) Common base plate of required strength manufactured out of MS channels. e) Suitable RCC foundation and anti vibration damping arrangement with cushy foot or similar mounting arrangement. f) Coupling and coupling guard for direct coupling of pump and motor. g) Pressure gauge with valve on the delivery side. h) Strainer at inlet. The pump set as described above ( Two each for supply UG Tank and for drain and over folw underground tank .

Providing & fixing M.S. class ‘C’ (heavy duty) pipe & fittings like tees, elbows, junctions, unions, bends, plugs etc. RCC pipe sleeves of larger diameter to the provided wherever the pipes are crossing the wall / slab and sleeves as per Consultant’s requirement, including clamps hangers, nuts, bolts etc for pipe supports from wall / ceiling and wrapping of under Ground pipe with wrapping coating material including cutting and making hole in wall / slab and making good the same. Including a coat of Synthetic enamel paint over two coats of primer complete as required.

25 mm dia

40 mm dia

50 mm dia

80 mm dia

Excavation of required depth and back filling with compaction in soil for HSD fuel oil piping including ramming the earth and making good.

Pipe up to 100 mm dia

Providing & fixing CI plug valves of the following sizes suitable for pressure of 10 kg/sqcm complete with all necessary fittings

25 mm dia

40 mm dia

50 mm dia

80 mm dia

Providing & fixing G.M. non return valves of the following sizes C131suitable for pressure of 10 kg/sqcm complete with all necessary fittings

40 mm dia

Providing and fixing gun metal float valve with copper float ball and brass rod of required length suitable for pressure of 10 kg/sqcm complete as required.

25 mm dia

Providing and fixing gun metal foot valve with necessary fittings complete as required.

40 mm dia

Providing and fixing flame proof level controller for day oil storage tanks, including wiring, cabling, probes with all other accessories ready for automatic operation of fuel oil pump complete as required.

Providing & fixing level indicator in plant room for UG oil storage tanks, including wiring, cabling, probes with all other accessories ready for working complete as required. Level indication shall be compatible with BAS system

Providing & fixing oil flow meter with flanged end for HSD service

40 mm dia

Providing and fixing Y strainer for oil supply line

50 mm dia

Providing & fixing unloading point consisting of 1 No. ‘Y’ strainer, with 1 No. Ball valves on inlet, outlet & by pass 1 No. drain valve, 1 No. 3 meter long flexible hose with necessary suitable connection for all oil tanker outlet

50 mm dia

Providing & fixing GM collection assembly fitted with lockable brass cap suitable for local oil tanker

HSD Tank for HSD transfer and Overfolw and Drain Tank:- Supply, installation, testing and commissioning of 990 litres secondary oil storage tank for collecting overflow oil from day oil tanks. fabricated from 4 mm thick MS plates. Tank shall include 450 mm ID manhole cover flanged connection for inlet, outlet, vent, DG and probe provision for level controller. Tank shall be installed underground and painted with 2 coats of red oxide primer. The work includes All civil works e.g excavation, grouting the tank in CC foundation, sand filling , refilling, masonary work, protection around the tanks etc complete as required.

ELECTRICAL WORKS : MV SWITCHGEAR PANELS : (PTA) HSD Pumps Panel as desciribed in SOQ Item No. 74 of tender documents. Note: 1) The work will be carried out as per best engineering practice in the industry. 2) Necessary approval from statutory authorities will be taken at suitable stages and finally before / after commissioning as per local by laws.

SUBHEAD - 'C' LIGHTENING PROTECTION SYSTEM WORKS Supply, Installation, Testing and Commision of Lightening Protection System complete as required as per items below:

Parallel Connectors for (500mm air terminal) connecting two conductors in parallel manner. Material- StSt, with clamping range- Rd / Rd 7-10 mm & Complied as per Standard EN 62561-1, etc. complete as required.

Angled Air-termination Rods having total length- 1000 mm, materia- Al & diameter of - Ø 10 mm. The air-termination rod is fixed at the metal support structure of the PV modules by two saddle clamps, etc. complete as required.

Air-termination rod having length- 1500 mm, of Material- AlMgSi, of Diameter Ø 16 / 10 mm, chamfered on both ends, & Complied as per Standard EN 62561-2, etc. complete as required.

For protecting the roofing sheets under the concrete base(17 kg.). The Diameter Ø outside 370 mm, Diameter Ø inside 360 mm and Material EVA, etc. complete as required.

Concrete Block -Round-17Kg, etc. complete as required.

Air-termination rod clamps for connecting air-termination rods with one or two conductors. Material of clamp Al, with clamping range of air-termination rod 16 mm and Clamping range of conductor Rd 2x 8-10 mm, & Complied as per Standard EN 62561-1., etc. complete as required.

Connection Clamps for Steel/metal column. Clamping range of the clamp- 3-18 mm, Material of the clamp- SS, Clamping range of conductor Rd 6-10 mm, & Complied as per Standard EN 62561-1, etc. complete as required.

Air-termination rod having length- 2000 mm, of Material- AlMgSi, of Diameter Ø 16 / 10 mm, chamfered on both ends, & Complied as per Standard EN 62561-2, etc. complete as required.

Air-termination rod having length- 2500 mm, of Material- AlMgSi, of Diameter Ø 16 / 10 mm, chamfered on both ends, & Complied as per Standard EN 62561-2, etc. complete as required.

Air-termination rod having length- 3000 mm, of Material- AlMgSi, of Diameter Ø 16 / 10 mm, chamfered on both ends, & Complied as per Standard EN 62561-2, etc. complete as required.

Side Wall Clamp for air terminal, Material - SS 304, Clamping range - 16/10 mm, etc. complete as required.

Air-termination rod clamps for connecting air-termination rods with one or two conductors. Material of clamp Al, with clamping range of air-termination rod 16 mm and Clamping range of conductor Rd 2x 8-10 mm, & Complied as per Standard EN 62561-1., etc. complete as required.

Universal connector of Material- StSt, with clamping range- 8-10mm, with truss head screw M10x35 mm & Complied as per Standard EN 62561-1, etc. complete as required.

Roof Conductor of Diameter Ø- 8 mm, Cross-section- 50 mm2, of Material- AlMgSi & Complied as per Standard EN 62561-2, etc. complete as required.

Roof conductor holder FB2 for flat roofs with concrete block-C35/45 with double conductor holder- Rd 8 mm fixed, Dimension- 141 x 86 x 70 mm, etc. complete as required.

Conductor holder for Parapet wall/Side wall. Having height- 16 mm, Thread of conductor holder- M8, Material of conductor holder- plastic, Conductor leading- loose, Conductor holder support Rd- 8 mm, With accessories Screw and Gitty, Material SS (M5 x 50mm), etc. complete as required.

Down Conductor of Diameter Ø- 8 mm, Cross-section- 50 mm2, of Material- AlMgSi & Complied as per Standard EN 62561-2, etc. complete as required.

Conductor holder for Parapet wall/Side wall. Having height- 16 mm, Thread of conductor holder- M8, Material of conductor holder- plastic, Conductor leading- loose, Conductor holder support Rd- 8 mm, With accessories Screw and Gitty, Material SS (M5 x 50mm), etc. complete as required.

EARTHING

UNI Disconnecting Clamps with intermediate plate for round and flat conductor of Material- StSt, Material thickness- 2.5 mm, with clamping range- Rd / Fl 8-10 / 30 mm, & Complied as per Standard EN 62561-1., etc. complete as required.

GI flat (25x6mm) Strip. Having width- 25mm, Thickness- 6mm, Material- Hot dipped Galvanized Iron, Cross Section- 150 Sqmm ,Coating thickness- Avg. 70 microns. & Complied as per IEC 62561-2., etc. complete as required.

GI strip holder of material- Dow moulded compound, having height- 19mm, Slot Size- 25x6 mm., etc. complete as required.

Copper bonded rod with Low carbon steel, high tensile strength copper bonded rod with min 254 microns of copper plating, UL listed with company name marked on rod. Diameter- 17.2 mm, Length- 3 meters, Material- Copper Bonded, Coating thickness- 250 microns, min, Approvals- Tested acc. IEC / EN 62561-2, UL 467., etc. complete as required.

Environment friendly, RoHS certified, low resistivity Ground Enhancement material in 22.6 Kg pack to fill the bore area around the rod, etc. complete as required.

SS 316 grade clamp to terminate the load on earth electrode. Dimension- 160x35x3 mm, etc. complete as required.

Poly plastic pit cover of material- Polymer Body & Cover, Product Code- HEP, Dimensions- 308 mm (L) x 308 mm (W) X 214 mm (H), Weight 2.5 kg (5.50 LBS)., etc. complete as required.

GI flat (25x6mm) Strip. Having width- 25mm, Thickness- 6mm, Material- Hot dipped Galvanized Iron, Cross Section- 150 Sq.mm,Coating thickness- Avg. 70 microns. & Complied as per IEC 62561-2. (for Interconnecting Earth Pits), etc. complete as required.

BUILDING AUTOMATION SYSTEM WORKS

CENTRAL CONTROL STATIONS Supplying, installing, testing & commissioning of the central control stations consisting of Intel Core i7-4790, 3.4 GHz or above processor, licensed version of OS window 10 professional & MS office package, 64 bit or later, multiple Hard disc of minimum 1TB capacity, Graphics Card 4 GB, 16 GB DDR3 RAM, inbuilt speakers, any PC compatible wireless mouse & Keyboard, 1 KVA online UPS for PC, 2 no USB port, 1 no Ethernet port (1Gbps speed).

Supplying, installing, testing & commissioning of the Colour Monitor LED- 32''

Supplying, installing, testing & commissioning of the A4 Size Color laser Printer for printing at both side of page.

SOFTWARE Supplying, installation, testing and commissioning of the Graphical Software providing the facility to create / provide the following, static and animate the graphics, navigation between pages, display of logs, changing the time zones, popup alarms, with minimum of 1 user license configurable password protection for BMS as per Specifications. The BMS platform shall natively support standard communication protocols such as BACnet™. The software should be web based software required to remotely monitor the system for 5 concurrent users. The BMS software should have email facility for sending critical alarms or can receive the pop-up in BMS software when alarm triggers. There shall be minimum 5 simultaneous users. Software shall be integrated other third party devices. Software shall permit use of standard web browsers. The software shall be programmable without the use of a dongle. The BMS module of the integrated software shall also be capable of working with 'Third Party' BACNET / Modbus compliant DDC controllers and shall receive or send data without the need for any additional configuration / licence. The software shall be able to connect to the various devices, collect the values from them, provide outputs to them as per logics, store required datas. The software shall also provide a rich graphic user interface which shall be specially developed for touch screen functions and user friendly interface. There shall be a set of trends and reports that can be viewed from the server station or through mobile or web access. These reports shall have dedicated buttons on the trends / reports page for an user to obtain them at a single click / touch.There shall be a set of trends and reports that would be mailed to different users at pre-determined periods.

Supplying, installation, testing and commissioning of the web based router / network area controller interfacing the DDC controllers, Modbus RTU/ BACnet MSTP for 3rd Party Devices for the system with PC. Same controller shall be used for 3rd Party devices and DDC. It has capacity to store trends & program backup. It should be BTL & UL Listed and shall be of the same make as DDCs.

CONTROLLERS Supply, Installation, Testing & Commissioning the following equipment for BAS. The controllers shall be UL listed, 32 bit microprocessor based standalone with real time clock. The DDC's shall be capable of peer to peer communication with other DDCs and then to router Also with locable MS mounting cabinets (IP54 rating vandal proof) duly powder coated connector strip, internal wiring and space to house controller & relays, connector strip current transformer, MCB, internal wiring. Contractor shall confirm his I/O provision w.r.t requirement on basis of datapoint. DDCs requiring more than 2 additional Plug in type IO Module cards or expansion modules to suffix the requirement of required inputs/outputs are not acceptable. Use of AI to DI multiplexer is also not acceptable. DDCs shall be compact factory fitted with IO Points. Each controller must have minimum 10% spare points capacity. Maximum 32 points per controller shall be allowed.

Supply, installation, testing & commissioning of DC Voltage Transducer

Supply, installation, testing & commissioning of Flameproof Level Switch

Supply, Installation, Testing & Commissioning of Unshielded Twisted pair multistanded tinned copper Signal Cables, 2 C x 1.0 Sq.mm. armoured

Supply, Installation, Testing & Commissioning of Shielded Twisted pair multistanded tinned copper Signal Cables, 2 C x 1.0 Sq.mm. armoured

Supply, Installation, Testing & Commissioning of Cat 6A armoured cable

Supply, Installation, Testing & Commissioning of 3 C x 1.5 Sq.mm. copper conductor armoured power cable. Note: 1) LV cable trays shall be utilised for laying of BAS cables. Wherever LV cable trays are available, BAS cables shall be laid on it. 2) Distribution board, MCBs wil be covered in Electrical work.

Comprehensive Maintenance (routine & preventive) of the of the following services comprising of all the machinery, equipment etc for 5 years after defect liability period etc. complete as required. Payment shall be made on quarterly basis. 3 x 2000 KVA 11 KV DG Sets

1st year

2nd year

3rd year

4th year

5th year

Comprehensive Maintenance (routine & preventive) of the of the following services comprising of all the machinery, equipment etc for 5 years after defect liability period etc. complete as required. Payment shall be made on quarterly basis. 1 x 500 KVA 415 V DG Set.

1st year

2nd year

3rd year

4th year

5th year

Annual maintenance contract of complete PLC Panel, 11 KV Synchronization panel, NGR & NIS Panels, and Incoming /outgoing DG set panel i/c incoming / outgoing breakers, buscouplers breakers, controller units etc. complete as required. Payment shall be made on quarterly basis. (This will include all 11 KV/415 V Panels connected with DG Sets) (For 5 year after defect liability period)

1st year

2nd year

3rd year

4th year

5th year

Annual maintenance contract of 5 years of complete Building Automation System after DLP period including field devices, softwares etc. complete as required. The maintenance of the first year of DLP period shall be free. Payment shall be made on quarterly basis as per schedule below after the first year.

1st year

2nd year

3rd year

4th year

5th year

Bidder Name

Amount in Words

Sterling And Wilson Pvt Ltd

PRAGYA ELECTRIC AND ELECTRONICS CORPORATION

SHALAKA INFRATECH I PVT LTD

S.L. ELECTROMECH PVT. LTD.

S. T. ELECTRICALS PVT. LTD.

ABSOLUTE PROJECTS (INDIA) LTD

HITECH ERECTORS PVT. LTD.

Bhanwariya Infra Projects Pvt Ltd

BLUE STAR LIMITED

Sudhir Power Projects Limited

PRAGYA ELECTRIC AND ELECTRONICS CORPORATION

Sudhir Power Projects Limited

SHALAKA INFRATECH I PVT LTD

S.L. ELECTROMECH PVT. LTD.

Bhanwariya Infra Projects Pvt Ltd

Sterling And Wilson Pvt Ltd

BLUE STAR LIMITED

S. T. ELECTRICALS PVT. LTD.

ABSOLUTE PROJECTS (INDIA) LTD