PROVN OF R4 REPAIR SEC FOR REPAIR SMALL ARMS AT 114 FD WKSP COY OF 7014 EME BN SR FOR REWIRING OF PROJECTOR ROOM AND SR TO 06 BATHROOM OF RICHEN AUDITORIUM AND SR TO REPLACEMENT OF INTERNAL WIRING TO CERTAIN TOILETS IN 14 COSR GE UNDER 865 EWS

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard/ dense soil , including spreading and levelling in layers n exc 25 cm thick complete all as specified and directed by Engr-in-Charge.

Excavating in trenches, n. exc 1.5 m wide and exc 1.5 m and not exc 3.00 m in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, for laying cables/pipes, etc. n exc 10 sq m on plan in hard/dense soil and getting out soil, complete all as specified and as directed by Engineer-in-charge.

Returning filling in (soil) including spreading, levelling, watering and well ramming in layers n.exc 25cm thick in any type of soil complete all as specifed and as directed by Engineer-in-Charge.

Removal of excavated material (soil) to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specifed and as directed by Engineer-in-Charge.

M&L for Plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in sub base, foundation, filling and mass concrete, complete all as specified and as directed by Engineer-in-Charge.

M&L pre-cast cement concrete(20mm graded crushed stone aggregate) 1:3:6 type C-1 as in block masonery exc 10cm in width with solid block masonery with solid blocks,exc.10cm in width and setting in cement mortar 1:6 all as Specified by Engr-in-Charge.

M&L pre-cast cement concrete(20mm graded crushed stone aggregate) 1:3:6 type C-1 as in block masonery 10cm in width with solid block masonery with solid blocks, and setting in cement mortar 1:6 all as Specified by Engr-in-Charge.

M&L for use & waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, well wall, sides and soffits of foundation and plinth beams and similar work: vertical or to batter complete all as specified and directed by Engr in Charge.

M&L for use & wase of formwork to sides of pllars, posts, struts, piers, columns and stanchions, Square, rectangular or polygonal for rough finished flat surface of concrete complete all as specified and as directed by Engr-in-Charge.

M&L for use & waset of formwork to rough finished concrete surfaces to sides of soffits of floor or roof beam, beam haunching, girders, bresumers, lintels, cantilever, shelves, Square, rectangular or polygonal for surface of concrete complete all as specified and as directed by Engr-in-Charge.

M&L for use & waset of form work to soffits of suspended slabs such as roof, floor slabs, landing, stair case etc not exc 200 mm thick horizontal or slopping rough finished concrete surfaces complete all as specified and directed by Engr-in-Charge.

M&L for use & waste of form work to edges of concrete rough finished not exc 20 cm thick complete all as specified and directed.

M&L for 40 mm thick cement concrete 1:2:4 type B-0 as in damp proof course horizontal or vertical surfaces including with water proofing compound @ 200 ml per bag of cement with necessary formwork if required complete all as specified and directed by Engr-in-Charge.

M&L for RCC M-30(Design mix) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed by Engr-in-Charge.

M&L for Reinforced cement concrete M-30 (design mix) in Beams, cantilivers, bressummers, lintel over 1.5 mtr span complete all as specified and directed by Engr-in-Charge.

M&L for Reinforced cement concrete M-30 (design mix) in Columns, vertical band, pillars, piers, posts and struts complete all as specified and directed by Engr-in-Charge.

M&L RCC M-30 (design mix) for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and as directed by Engr-in-Charge.

S&F mild steel TMT bars of 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips , complete all as specified and directed by Engr-in-Charge.

All as per item No. 18 here-in- before but up to and including 6 to 8 mm dia in stirrups, spacers and binders as in columns and beams etc. as specified and directed by Engr-in-Charge.

M&L for hard core of broken stone or boulders of gauge n.exc 63 mm deposited, spread and level in layers n. exc. 15 cm thick watered and rammed to true surface complete all as specified and directed by Engr-in-Charge.

M&L for 75mm PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in sub base of floor all as specified by Engr-in-Charge.

M&L for 75mm thick PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in plinth protection and finished concrete surface even and smooth without using extra cement including making proper joints with bitumen mastic with sand as per specification at an interval of 3m and change of direction complete all as specified and as directed by Engr-in-Charge.

M&L for 25mm thick PCC 1:2:4, type B-1 using 20mm graded crushed stone aggregate as in sub base/ levelling course for laying of screed bed complete all as specified by Engr-in-Charge.

M&L Machine cut pre mirror polished Kota stone slab uniform colour flooring 20-25 mm thick over 20mm thick cement screed bed or bedding layer in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of slab complete all as specified and directed by Engr-in-Charge.

M & L for joint free Non-Skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed or bedding layer in Cement Mortar 1:6 for laying floor finishes complete all as specified and directed. MAKE: KAJARIA/H&R JOHNSON/CERA/ NITCO/SOMANY

M&L for (350mmx250mmx7mm/450mmx350mmx 7mm thick) coloured glazed ceramic tiles set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments.(Note: Any disturbed surfaces shall be matched w/o any extra cost to the govt) incl 10mm thckbacking coat for dado/skirting CM 1:4 complete all as specified and directed by Engr-in-Charge. MAKE: KAJARIA/H&R JOHNSON/CERA/ NITCO/SOMANY

M&L for 2nd class hard wood as in plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and as directed by Engr-in-charge.

S&F Factory made 35mm thick IInd Class Hard wood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified and directed by Engineer-in-Charge.

S&F 30mm thick, factory made 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete, all as specified and directed by Engr in Charge.

M&L for Mild Steel Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:3:6 type C-1 using 20 mm graded crushed stone aggregate, as in hold fast, bed blocks and the like complete all as specified and as directed by Engr-in-Charge.

S&F for Aluminum, anodized, barrel tower bolts, ISI Marked, of extruded section 150 mm long, complete all as specified and directed by Engr-in-Charge.

S&F for Butt hinges, medium weight, cold rolled mild steel and fixed with screws to wooden frames or with welding to existing MS frames,100 mm size, ISI marked, complete all as specified and directed by Engineer-in- Charge.

S&F for 300mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and as directed by Engr-in-Charge.

S&F 100mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed by Engr-in-Charge.

M&L for rendering 15mm thick rendering in cement mortar 1:6 on fair faces of brick walls or on concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

M&L for rendering 15mm thick rendering in cement mortar 1:4 other than fair faces of brick walls or on concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

M&L for 5mm thick rendering on fair faces of concrete surface of ceilings finished even and smooth without using extra cement in cement mortar 1: 3 complete all as specified and as directed by Engr-in-Charge.

S&F Plain Sheet sheet glass 4.00 mm thick, ordinary quality and glazing with oil pane putty in squares not exceeding 0.5 Sq. mm in each pane, complete, complete all as specified and as directed by Engr-in-Charge.

S&F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples, fixed in repairs complete all as specified and as directed by Engr-in-Charge.

M&L for mild steel confirming to Fe 290 Gde E-165, hand rails, half round or other steel section or core for wooden hand rail straight portion, window grill, drilld and counter sunk or balusters running bars for doors, including embedded in concrete and screwing etc wind ties for roof including securing bolts, posts and struts in fencing complete all as specified and directed by Engr-in-Charge.

M&L for Preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed by Engineer-in-Charge.MAKE: NEROLAC PAINTS/ JENSON & NICHOLSON/BERGER PAINTS/ICI DULUXE/ASIAN PAINTS

M&L for Preparation of old treated plastered / unplastered surfaces of walls and applying two coats of cement base paints of any shade on walls (shade as approved by users) including curing before and after applying each coat complete all as specified and directed by Engineer-in-Charge. MAKE: SNOWCEM / ASIAN / JEHNSON & NICHOLSON / BERGER / DURACEM

M&L for Preparation of newly plastered surfaces of walls and applying two coats of distempering with oil bound distemper white or any tinted on walls, filling gaps by putty after washing rubbing down and stopping of distermpered surfaces, over a coat of primer complete all as specified and directed by Engr-in-charge. MAKE: NEROLAC PAINTS / JEHNSON & NICHOLSON / BERGER PAINTS / ICI DULUXE / ASIAN PAINTS

M&L for three coat of white wash on newly plastered surfaces ceiling including preparation complete all as specified and directed by Engr-in-charge.

S&F in19mm dia mild steel, chromium plated curtain rods, with brackets, end Dooms all as specified and as directed by Engr-in-Charge.

M&L for second class soft wood clean swan as in battens for grids of ceiling and lining, plain fillets exc 13 sqcm and n.exc 25 sqcm, square/ rectangular in section, secured with nails or brads to timber frame work including dismantlng fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc under 40 Sq.cm in section complete all as directed by Engr-in-Charge.

M&L for second class soft wood clean swan as in beading for edges of ceiling, lining, wooden flooring work, plain fillets exc 6 sqcm and n.exc 13 sqcm, square/ rectangular in section , secured with nails or brads to timber frame work complete all as specified and directed by Engr-in-Charge.

M&L for 9mm thick prelaminated particle board, medium interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete all as specified and as directed by Engr-in-Charge. MAKE: NOVA PAN/GREEN PLY BHUTAN BOARD/MYSORE WOOD BOARD/CENTURY PLYWOOD

M & L for providing and fixing Gypsum boards 12 mm thick in ceilings fixed with screws as per manufacturers instructions including anodised aluminium snap grid frame work of size 605 x 605 mm with anodised aluminium channel supports/ angles/ 'T' (Main tee 35 x 25 x 1.5 mm, cross tee 25 x 25 x 1.4 mm and wall angle 32 x 32 x 2 mm) fixed with screws/ plugs etc including GI suspenders of 6mm dia upto 1200 mm length adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size as per approved pattern and design complete all as specified and directed by Engr-in-Charge.

M&L for 18/19 mm thick block board core, grade 2 quality interior grade, commertial type fixed with screws to timber frame work complete all as specifeid and directed by Engr-in-Charge.

S&F 100 mm Hasp and staple, safty type aluminum anodised hinge pin type including bolt to hinge plate with screws complete all as specified and directed by Engr-in-Charge.

S&F Brass knob 35-40 mm dia fixed to plywood surfaces with bolt type screws complete all as specified and directed by Engr-in-Charge.

S&F 30 mm wide when opening contineous piano hinges, mild seel bright finish fixed to plywood complete all as specified and directed by Engr-in-Charge.

M&L for 75 mm bore, PVC (SWR) pipes, pressure rating 6 kg/sqcm, single or double socketed, in any length with rubber ring joints, fixed to walls, laid in trenches or in floors complete all as specified and as directed by Engr-in- Charge. MAKE: SUPREME/ASHIRWAD/FINOLEX/ SFMC/ASTRAL

M&L for 110 mm bore, PVC (SWR) pipes, pressure rating 4 kg/sqcm, single or double socketed, in any length with rubber ring joints, fixed to walls, laid in trenches or in floors complete all as specified and as directed by Engr-in- Charge. MAKE: SUPREME/ASHIRWAD/FINOLEX/ SFMC/ASTRAL

S&F PVC (SWR) Floor tap 100/110mm bore compele all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) bents 110 mm bore complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) vent cowl 110mm bore complete all as specified and directed by Engr-in-Charge.

Stack clamps made out of 50 x 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore pipe, complete all as specified and as directed by Engineer-in-Charge.

S&F Vitreous china water closet, 'Orissa' pattern, including lime concrete bedding, size 580 x 440 mm white with integral foot rests excluding flushing cistern and flush pipe but including connection to trap, anti syphonage pipe etc. complete fixed in repairs, incl bedding with PCC 1:2:4 type B-1 using 20 mm grade stone aggregate complete all as specified and as directed by Engr-in-Charge. Make: Cera/Hindware/Parryware

S&F sand cast iron 'P' or 'S' trap 100 mm bore for indian type WC complete all as specified and directed.

S&F Vitreous China bowl urinal flat back, half stall type white (minimum), with grating and union for discharge pipe, waste coupling complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement;, flush pipe, grating and Union for discharge pipe complete all as specified and directed by Engr-in-Charge. Make: Cera/Hindware/Parryware

S&F Viterous china wash basin, white flat back size 580x 450mm including waste coupling CP 32mm dia and CI brackets of iron 65 x 65 x 6mm embedded in PCC block with PCC 1:2:4 type B-1 and PVC waste pipe 32mm dia & CP grating with holes fixed complete, all as specified and as directed by Engr-in-Charge. MAKE: CERA/HINDWARE/PARRYWARE

S&F 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with twin flush provision, complete, all as specified and as directed by Engr-in-Charge. MAKE: Cera Model Combiflush twin flush as per Cat Part No. B1020101 (Old Cat Part No 2603) or equivalent in HINDWARE/PARRYWARE

S&F soap dish chrome finished stanless steel complete all as specified and directed by Engr-in-Charge.

S&F 600 mm x 450 mm mirror of thickness 5/5.5mm of slected quality glass, mounted on 6 mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete, fixed in repairs all as specified and as directed by Engr-in-Charge. MAKE: SAINT GOBAIN/MODI GUARD/TRIVENI FLOAT GLASS

S&F 20mm bore chromium plated, fancy type Stop valve/cock, cast copper alloy, screwed down, high pressure with handle, chromium plated, screwed end for iron pipe or for union and fixed, complete all as specified by Engr-in-Charge. MAKE: PARKO/MARC/ESS ESS/CERA

S&F 20 mm bore chromium plated, fancy type angle valve, cast copper alloy, screwed down, high pressure with handle, chromium plated, screwed end for iron pipe or for union and fixed, suitable for complete all as specified by Engr-in-Charge. MAKE: PARKO/MARC/ESS ESS/CERA

S&F PVC connections 15 mm size with PTMT nuts of length 600 mm long complete all as specified and diected by Engr-in-Charge. Make: Prayag/Polytuf/Supreme

S&F 15mm bore, piller tap chromimum plated fancy type high pressure with or without letter Hot or cold with long screwed shank and fly nuts screwed for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge. MAKE: PARYAG/POLYTUF/SUPREME

S&F 15mm bore, chromimum plated brass, Bib tap screwed for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge. MAKE: PARYAG/POLYTUF/SUPREME

S&F 20mm bore 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified. Make : JINDAL/KISAN/SFMC/Supreme/Kanha Plastic Pvt Ltd

S&F 25mm bore 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified. Make : JINDAL/KISAN/SFMC/Supreme/Kanha Plastic Pvt Ltd

S&F 25 mm bore chromium plated, fancy type angle valve, cast copper alloy, screwed down, high pressure with handle, chromium plated, screwed end for iron pipe or for union and fixed, suitable for complete all as specified by Engr-in-Charge. MAKE: PARKO/MARC/ESS ESS/CERA

S&F 25 mm bore ball brass valve high pressure with polythene float and fly nuts complete screwed for iron pipe or brass ferrule complete all as specified and directed by Engr-in-Charge.

S&F Rotational moulded polyethylene water storage PUF tank, PUF insulated with 75 mm thick PUF insulation of density not less than 48Kg/Cum, inner and out white, two layers, ISI marked (cylinderical vertical/rectangular/loft type with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 500 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes, including taking down of old broken water tank complete all as specified and as directed by Engr-in-Charge. MAKE: SINTEX/POLYWELL/ROTEX/POLYCON

Rotational moulded polyethylene water storage tank, inner and out white, two layers, ISI marked (cylinderical vertical with closed top) hoisted with threaded cap and fixed in position all as specified in SSR Part-I of Capacity 500 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes, including taking down of old broken water tank complete all as specified and as directed by Engr-in-Charge.

M&L for 75mm thick PCC 1:4:8 type B 2 (using 40mm graded stone aggregate) as in sub base of floors/ pavings etc complete all as specified and as directed by Engr-in-Charge.

M&L for Chequred cement concrete tiles PU coated glossy finished in size of 30cm X 30cm X 20mm thick, set ,pointed & jointed in neat cement slurry in floors polished with grey cement & pigments .Layed over 20mm thick cement screed base (1:4) and all as directed by Engr-in -Charge.

M&L for picking, swiping clean and washing down with wire brushing and cleaning top surface of new roof tarracing or cement concrete, including picking, sweeping, clean, washing down with water to remove dust and brushing neat cement slurry @ 3kg of cement per sqm including rendering 20mm thick in cement mortar 1:4 mixed with water proofing admixture (as per manufacturars instruction), over and including 25mm thick PCC 1:2:4, type B-0 using 12.50mm graded crushed stone aggregate finishing the surface even and rough, including applying normal treatment (for moderate conditions and laying of APP based polymeric membrane minimum weighing 3.6 Kgs/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150 gms/sqm) laid on primed surface by forced application complete all as specified laid over a coat of bituminous primer @0.3 ltr/sqm and finished with applying bitumen grade 85/25 coat @1.2 Kg/sqm. APP membrane shall be laid by torching with 75mm overlap in longitudnal direction and applying two coats of aluminium paint complete all as specified and directed by Engr-in-Charge.

S&F sinks stainless steel with drainage board made of 1.0 mm thick kitchen or laboratory with plugs, washers and wastes; including fixing contilever brackets and connecting union to pipe overall size 495mm x 420 mmmm bowl size 410mm x 330mm x 160mm, complete all as specified. Make : NIRALI/NEELKANTH/JAYNA/SILVERSHINE/JINDAL

M&L forming contraction (Dummy) joints 50 mm deep x 10mm wide for plinth protection & similar work , filled with sealing compound Grade 'A' in plinth protection complete all as specified and directed by Engr-in-Charge.

Excavating over areas, n exc 1.5 m deep and getting out hard/dense soil complete all as specified and directed by Engr-in-Charge.

Excavating over areas, exc 1.5 m but not exc 3.00 m deep and getting out hard/dense soil complete all as specified and directed by Engr-in-Charge.

M&L for Walling of random rubble, uncoursed stone masonary, well bonded, laid dry in retaining wall, abutment and similar work built in cement mortar 1.:6 complete all specified and as directed by Engr-in-Charge.

M&L for Providing, cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregates) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, bed blocks for hold fasts, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, all as specified and directed by Engineer-in-Charge.

M&L Reinforced cement concrete (Nominal mix) 1:2:4 type B1, (using 20 mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and as directed by Engineer-in-Charge.

M&L for providing precast reinforced cement concrete type A1, 1:1.5:3 using 20mm graded aggregate as in landings, cover slabs (for man holes etc) and similar articles with plain faces and setting in cement mortar 1:6 complete with joints to match including use of necessary formwork all as specified and directed. Note : S&F reinforcement shall be measured and paid separately.

Material and labour for Concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 for 150 mm bore pipes including S&F 150 mm dia PVC SWR pipes single socketed in any length complete all as specified and directed by Engr-in-Charge.

M&L broken stone for loose filling of guage 80mm to 150 mm graded for soak wells complete all as specified and directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tile to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

M & L for joint free Non-Skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed or bedding layer in Cement Mortar 1:6 for laying floor finishes complete all as specified and directed. MAKE: KAJARIA/H&R JOHNSON/CERA/ NITCO/SOMANY

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt), complete all as specified and directed by Engineer-in-Charge.

Supply and fix factory made PVC internal door frame of the size 50mmx47mm with a wall thickness of 5mm, made out of extruded 5mm thick prelam sheet, mitred cut at two corners and jointed with 2 nos. of 150mm long brackets of 15mmx 15mm MS tube. The two vertical door profiles are to be reinforced with 40mmx20mm MS tube of 19 gauge through out the frame. The door frame shall be fixed to the wall using 65/100mm long MS Screws through the frame by using PVC fasteners. A minimum of 4 nos. of screws to be provided for each vertical member & minimum 2 Nos. for horizontal member etc. complete as per manufactures specification and directed by Engineer-in-charge

Supply and fix 30mm thick factory made solid PVC Moulded door shutter, consisting of solid core single leaf flush door of 30mm thickness, lipped with 15mm(5mmx3) thick 30mm width on the other stiles & bottom rails. The inner panel laminated with 2mm thick termite proof and fire resistant moulded PVC sheet with 2,4 or 6 raised panel design in different plain and / OR prelam colours on one side after routing the moulded design on flush door & 2mm thick plain and/ OR prelam PVC sheet on the other side using rubber adhesive on flush door & solvent cement adhesive on the PVC lipping etc complete as per direction of Engineer -in charge, manufacturer’s specification and drawing

Taking up or down 15 mm dia steel tubing/16mm 3 layer PP-R polypropylene random copolymer and connections including cleaning for refixing or removal to store complete all as specified and directed by Engr-in-Charge.

Taking up or down 20 mm dia steel tubing/16mm 3 layer PP-R polypropylene random copolymer and connections including cleaning for refixing or removal to store complete all as specified and directed by Engr-in-Charge.

Supply and fix 15mm bore medium grade galvanised steel tubing with all fittings and fixed complete to wall, ceiling or laid in floor complete all as specified and as directed.

S&F in repair PP-R 20mm bore Gate valve (with brass ferrule as per site reqirement antimicrobial fusion welded having thermal stability for hot & cold water supply . complete all as specified and directed by Engr-in-Charge. Make : JINDAL/KISAN/SFMC/Supreme/Kanha Plastic Pvt Ltd

M&L for cutting chasing to brick walls, pinning, making good to facings where required and pointing in cement mortar 1:3 to ends and making good cutting exceeding 200 mm thick wall complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC 32 mm dia waste pipes fixed to wash hand basin, urinals, sink etc complete all as specified and directed by Engr-in-Charge.

S&F in repair 15mm bore, chromimum plated brass, Bib tap screwed for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge.

S&F in repair health faucet, (ABS body) mild steel chromium plated suitable for 15 mm dia pipe with 1.20 mtr long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed by Engr-in-Charge.

S&F in repair 15 mm bore chromium plated, fancy type Stop valve/cock, cast copper alloy, screwed down, high pressure with handle, chromium plated, screwed end for iron pipe or for union and fixed, complete all as specified by Engr-in-Charge.

S&F in repair chrome finished stainless steel grating doom 100 mm dia of CP (minimum weight 60 gram) complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm long complete all as specified and directed by Engr-in-Charge.

S & F in repair towel rail 600mm long of aluminum 20 mm dia, D type fixed with and including chrominium plated brass screws and wooden/plastic cleats complete all as specified and directed by Engr-in-Charge.

S&F in repair 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with twin flush provision, complete, all as specified and as directed by Engr-in-Charge. MAKE: Cera Model Combiflush twin flush as per Cat Part No. B1020101 (Old Cat Part No 2603) or equivalent in HINDWARE/PARRYWARE

S&F in repair Vitreous China wash down water closet pan and seat cover (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including P or S trap and including plastic water closet seat, black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device, including connection to drain pipe (or out going pipe) and to flushing pipe, antisyphonage pipe, etc. including cast iron 'P' or 'S' trap for 100mm bore of pipe, complete all as specified and as directed by Engr-in-Charge.

S&Fin repair Vitreous china water closet, 'Orissa' pattern, including lime concrete bedding, size 580 x 440 mm white with integral foot rests excluding flushing cistern and flush pipe but including connection to trap, anti syphonage pipe etc. Incl bedding with PCC 1:2:4 type B-1 using 20 mm grade stone aggregate complete all as specified and as directed by Engr-in-Charge. Make: Cera/Hindware/Parryware

S&F in repair Viterous china wash basin, white flat back size 580x 450mm including waste coupling CP 32mm dia and CI brackets of iron 65 x 65 x 6mm embedded in PCC block with PCC 1:2:4 type B-1 and PVC waste pipe 32mm dia & CP grating with holes fixed complete, all as specified and as directed by Engr-in-Charge. MAKE: CERA/HINDWARE/PARRYWARE

S&F in repair 15mm bore, piller tap chromimum plated brass fancy type high pressure with or without letter Hot or cold with long screwed shank and fly nuts screwed for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge. MAKE: PARYAG/POLYTUF/SUPREME

S&F in repair Vitreous China bowl urinal flat back, full stall type white (minimum), with grating and union for discharge pipe, urinal spreader, waste coupling complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, flush pipe, grating and Union for discharge pipe complete all as specified and directed by Engr-in-Charge. Make: Cera/Hindware/Parryware

S&F in repair toilet paper holder with flat recessed type stainless steel complete all as specified and directed by Engr-in-Charge.

S&F in repair 600 mm x 450 mm mirror of thickness 5/5.5mm of slected quality glass, mounted on 6 mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed by Engr-in-Charge. MAKE: SAINT GOBAIN/MODI GUARD/TRIVENI FLOAT GLASS

S&F in repair sheet glass self assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromimum plated bracket guard and railing 60 cm long complete all as specified and directed by Engr-in-Charge.

Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, including cutting of trees, shrubs or any type of vegitation upto and including roots complete all as specified and directed by Engineer-in-Charge.

Material and labour for complete removal of existing treatment on wall surfaces and applying 1.5 mm thick JK / Birla wall putty as per manufactures instructions, surfaces to be finished even and smooth over a coat of alkali resisstane primer and applying two coats of oil emulsion distember first quality of approved colour complete all as specified and directed by Engr-in-Charge.

M&L for complete removal of existing treatment on wall surfaces and applying wall care putty as per manufactures instructions, surfaces to be finished even and smooth over a coat of primer and applying two coats of exterior emulsion first quality of approved colour complete all as specified and directed by Engr-in-Charge.

Dismantling of upto 100 mm dia drain pipes, salt glazed ware, AC or reinforced concrete including fitting, jointed in cement mortar complete all as specified and directed.

S&F PVC (SWR) bents 75 mm bore complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) branch piece singe 'Y' equal or unequal, 75 mm bore complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) branch piece singe 'Y' equal or unequal, 110 mm bore complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) branch piece singe 'T' equal or unequal, 75 mm bore complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) branch piece singe 'T' equal or unequal, 110 mm bore complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) vent cowl 75 mm bore complete all as specified and directed by Engr-in-Charge.

S&F in repair, 15mm bore brass CP single liver WHB Mixture with popup waste system, 450mm long braided hoses & base flange complete all as specified and directed by Engr-in-Charge.

M&L for point wiring for one light point or fan point controlled by one light/exhaust fan controlled by one way switch with PVC insulated copper conductor stranded cable of size 1.5 sqmm and including PVC casing/caping terminated in existing sunk CI/pressed steel terminal boxes for fixing and 1.5 sqmm PVC insulated copper wire as earth wire connected to earth wire connected to earth folly and 3.0mm thick plastic laminated sheet cover all as specified and directed by Engr-in-Charge.

All as per item No 130.00 here-in-before but 1.5 Sqmm for one 3 pin 6 amps socket outlet including 1.5 sqmm insulated copper wire as earth wire to the same earth dolly on the same board complete all as specified and directed by Engr-in-Charge.

All as per item No 130.00 here-in-before but 1.5 Sqmm for one 3 pin 6 amps socket outlet including 1.5 sqmm insulated copper wire as earth wire to the same earth dolly on the independent board complete all as specified and directed by Engr-in-Charge.

All as per item No 130.00 here-in-before but for power point 3 pin switch socket 15 Amp with PVC copper conductor cable multistrand unsheathed 4.00 Sqmm on independent board incl one run 2.5 Sqmm multistrand PVC copper conductor cable for earth continuity in and including PVC casing and capping fixed on wall incl teak wooden board with 3mm thick of hylam top sheet complete all as specified and as directed by Engr-in-Charge

M&L for lamp holder PVC/Poly corbonate type insulated body with back plate suitable for batten fittings as specified and directed by Engr-in-Charge.

S&F switch piano flush type one way single pole 5/6 Amp 240 volts complete all as specified and directed by Engr-inCharge.

S&F switch socket combination 2 in 1, 5 pin, 5/6 Amps flush type universal complete allas specified and directed by Engr-in-Charge.

S&F switch socket combination 2 in 1, 5 pin, 5 and 15 Amps flush type universal complete all as specified and directed.

M&L for ceiling rose surface bakelite 65x50 mm two to three terminals complete all as specified and directed by Engr-in-charge.

Supply and fixing MCB distribution board Double door, regal grey, sheet metal enclosure, SPN 240 volts 8 way with 200 amps rated bus bar concealed to wall and making flush with wall surfaces and making good to disturbed surfaces of walls to match with the exisiting surface etc . Make: Cat part No 5076 11 of Legrand (Ekinoxe) or equal approved in Schneider (Acti-9)/Siemens (Betagard-8GB32)

Supply and fixing MCB SPN 40-63 Amps, 'C' series, 240 V A/C complete all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4085 96 of Legrand (DX³) or equal approved in Schneider (Acti-9)/ Siemens (Betagard-5SL4)

Supply and fixing MCB SPN 6 to 32 Amps, 'C' series, 230 V A/C complete all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4086 09 to 4086 17 of Legrand (DX³) or equal approved in Schneider (Acti -9)/ Siemens (Betagard-5SL4)

Supply and fixing of exhaust fan, steel body, AC single phase 230 volts of size 300 mm sweep with blades and frame and louvers complete all as specified and as directed by Engr-in-Charge.

Material and labour for earthing complete with galvanised steel earth plate 600 x 600 x 6 mm buried directly in ground vertically to a depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below ground level connected to and including GI wire of size 4 mm dia by means of nuts, bolts, washers etc made of and connected to test point and earth dolly as all shown in electrical plate No.3 of SSR Part-I 2009 and specified or indicated including excavation and earth work in any type of soil PCC (1:3:6) type C1 in chamber, pre cast RCC slab 50mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric or XPM jali (weight not less than 4.0 kg/Sqm) with cast iron frame, funnel, with wire mesh, 20mm bore medium grade GI watering pipe, lugs, 15mm bore light grade GI protection pipe, test point, etc, t complete all as specified and as directed. Note: (i) Item includes the cost of 7.5 m GI pipe for protection of earth lead. Any additional length shall be adjusted through deviation order. (ii) Item includes the cost of 7.5 m GI earth lead. Any additional in length shall be adjusted through deviation order ( For Main DBs ) (iii) Item includes the cost of Charcoal and commercial salt ( For Main DBs )

S&F LED bulk head light fitting 1x10watt 230 volt attractive wall/ceiling mounted any type with white reflactor complete with all accessories pre-wired and including connecting up with 3 core twisted flaxible copper conductor cable complete all as directed. Make : Cat part No HEXAFT10WLED857SSYMBOPC of Havells or equivalent in Bajaj/Philips

S&F LED lights fitting, TITANIA SLEEK NEW T5 LED TUBELIGHT (DOUBLE SIDE CONNECTION) (Double side Connection), 1x16 watt, 220 volts, AC ultra bright LED tube light with aluminium heat sink & polycarbonate diffuser having high efficacy suited for installation in existing T5 fitting with G5 lamp holders, led driver outside decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. Make : Cat part No TITANIASLEEK1149T5DSTL18WLED865SPC of Havells/ Philips/Bajaj/ Crompton

S&F LED street light, 35/36 Watts, ENDURA CITYLITE PLATLNUM PLUS energy saving and environmentalfriendly long life led street light made up of pressure die cast aluminium housing with high power led as lighting source and lens embedded PC cover having iP65 protection and impact resistance of IK07 with 10KV Built-in surge Protection device complete all as specified and as directed. Make : Cat Part No ENDURACITYLITEPLATPLUSSL35WLED757SASYBOPC of Havells or equivalent in Bajaj/Philips.

S&F 1100 V grade heavy duty cable PVC insulated aluminium conductor served with inner sheathing of pvc tape and over all pvc sheathed in service connection suspended by insulating hangers not more than 1 mtr apart including 4 mm suspension wire one twin core cable flat of stranded multistrand conductor size 10 sqmm complete all as specified and directed by Engr-in-Charge

S&F in strorage type water heaters, vertical type, 25 Ltrs capacity with Energy saving Incology 800 heating element, Feroglass coated tank with single weld line design, high density PUF insulation with power 2000 watts, operating voltage 220-240 volts, with superior heating performance and excellent resistance to both oxidation & carbonisation at high temp setting including of wall manual accessory and 2 flexi hot and cold water pipe complete alll as specified and directed by Engr-in-Charge. Make : CALENTA MECHANICAL of Bajaj or equal approved in Racold/Crompton/ Venus/Orient/Jaquar

PVC connections 15 mm size with PTMT nuts of length 450 mm, hot or cold type complete all as specified and diected by Engr-in-Charge.

Material and labour for earthing complete with galvanised steel earth plate 600 x 600 x 6 mm buried directly in ground vertically to a depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below ground level connected to and including GI strip of size 25x4mm as earthing leads by means of nuts, bolts, washers etc made of and connected to test point and earth dolly as all shown in electrical plate No.3 of SSR Part-I 2009 and specified or indicated including excavation and earth work in any type of soil PCC (1:3:6) type C1 in chamber, pre cast RCC slab 50mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric or XPM jali (weight not less than 4.0 kg/Sqm) with cast iron frame, funnel, with wire mesh, 20mm bore medium grade GI watering pipe, lugs, 40mm bore light grade GI protection pipe, test point etc complete including taking down of old u/s earthing set all as specified and as directed. Note: (i) Item includes the cost of 7.5 m GI pipe for protection of earth lead. Any additional length shall be adjusted through deviation order. (ii) Item includes the cost of 7.5 m GI earth lead. Any additional in length shall be adjusted through deviation order (iii) Item includes the cost of Charcoal and commercial salt

Supply & fixing Aluminium strip 25 x 3.15mm with porcelain insulators, saddles and fixing screws etc. for roof conductors and down conductors all as specified and as directed by Engineer-in-Charge.

S&F Air termination, single pointed aluminum rod 12 mm dia rod 300 mm long complete all as specified and directed by Engr-in-Charge.

S&F Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw complete all as specified and directed by Engr-in-Charge.

S&F earthing strip insulator to run the earth strip of size 25x15 mm complete including fixing arrangements complete all as specified and directed by Engr-in-Charge.

Supply, installation, testing and commissioning of ductable type standalone oil fired kerosene/HSD based hot air generator complete with stainless steel heat exchange chamber consisting of furnace fabricated out of high temperature resistance stainless steel, reflector, built in fuel oil piping exhaust chimeny all houssed in powder coated cashing suitable for operator on 50Hz single phase 230 Volt AC supply capacity 75000 Kcal/Hr. (a) Heat output - 50000 Kcal/Hr (b) Hot Air Temp - 40C (c) Temperatrue - 90C Max (d) Fuel consumption - 5.2-5.6 ltr/Hr (e) Thermal efficiency - 80-90% (f) Electric supply - 220 Volt 50 Hz (g) Tempertature control - Automatic (h) Fuel - Kerosene/Diesel (j) Burner - Riello/Ben-Tone Make : Top mind industries Pvt Ltd/ECCO Flame/Flameco/Thermex

Design, Supply and fixing testing ducting for hot air blower to room with complete insulation of the duct complete all as specified and directed.

Taking down carefully copper/Aluminum point wiring (Light, Fan, Socket or power) complete fitting such as switches, ceiling, regulator, sockets etc removing materials to be store for keeping in safe custody for taking credit and making good disturbed surfaces of walls, floors etc complete all as speciifed and directed.

Taking down of old sub main wirings at any description complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of switch piano flush type one way single pole 5/6 Amp 240 volts complete all as specified and directed by Engr-in-Charge.

S&F in replacement of switch socket combination 2 in 1, 5 pin, 5/6 Amps flush type universal complete all as specified and directed by Engr-in-Charge

S&F in replacement of switch socket combination 2 in 1, 5 pin, 5 and 15 Amps flush type universal complete all as specified and directed by Engr-in-Charge.

S&F in replacement of ceiling rose surface bakelite 65x50 mm two to three terminals complete all as specified and directed by Engr-in-charge.

Supply and fixing MCB distribution board Double door, regal grey, sheet metal enclosure, SPN 240 volts 8 way with 200 amps rated bus bar concealed to wall and making flush with wall surfaces and making good to disturbed surfaces of walls to match with the exisiting surface etc including taking down old DBs. Make: Cat part No 5076 11 of Legrand (Ekinoxe) or equal approved in Schneider (Acti-9)/Siemens (Betagard-8GB32)

Supply and fixing MCB distribution board Double door, regal grey, sheet metal enclosure, SPN 240 volts 12 way with 200 amps rated bus bar concealed to wall and making flush with wall surfaces and making good to disturbed surfaces of walls to match with the exisiting surface etc including taking down old DBs. Make: Cat part No 5076 11 of Legrand (Ekinoxe) or equal approved in Schneider (Acti-9)/Siemens (Betagard-8GB32)

Supply and fixing MCB distribution board Double door, regal grey, sheet metal enclosure, SPN 415 volts 4 way with concealed to wall and making flush with wall surfaces and making good to disturbed surfaces of walls to match with the exisiting surface etc including taking down old DBs. Make: Cat part No 5076 11 of Legrand (Ekinoxe) or equal approved in Schneider (Acti-9)/Siemens (Betagard-8GB32)

Supply and fixing in replacement of 415 V 10 KA 'C' curve TPN miniature circuit breaker (MCB) of 40 to 100 Amp 4 poles and current carrying capacity in theDB complete with connection testing and commissioning all as specified and directed by Engr-in-Charge.

Supply and fixing MCB SPN 40-63 Amps, 'C' series, 240 V A/C complete incl taking down old MCBs all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4085 96 of Legrand (DX³) or equal approved in Schneider (Acti-9)/ Siemens (Betagard-5SL4)

Supply and fixing MCB SPN 6 to 32 Amps, 'C' series, 230 V A/C complete incl taking down old MCBs all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4086 09 to 4086 17 of Legrand (DX³) or equal approved in Schneider (Acti -9)/ Siemens (Betagard-5SL4)

Supply and fixing of exhaust fan, steel body, AC single phase 230 volts of size 250 mm sweep with blades and frame and louvers complete all as specified and as directed.

S&F in replacement 36 watts QUADRO 2'X2' precisely designed decorative Pmma diffuser 2x2 panel light that unites a creative design with state-of-the-art led technology. the concept of protruded decorative diffusers achieves a great sense of novelty and flexibility with multiple diffuser designs while offering perfect illumination and greater uniformity. this design stands out stunningly among the boring old modular ceiling patterns complete all as specified and directed by Engr-in-Charge. Make : Cat Part No QUADRO2X2PLR36WLED857S of Havells or equivalent in Bajaj/Philips.

Material and labour for earthing complete with galvanised steel earth plate 600 x 600 x 6 mm buried directly in ground vertically to a depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below ground level connected to and including GI wire of size 4 mm dia by means of nuts, bolts, washers etc made of and connected to test point and earth dolly as all shown in electrical plate No.3 of SSR Part-I 2009 and specified or indicated including excavation and earth work in any type of soil PCC (1:3:6) type C1 in chamber, pre cast RCC slab 50mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric or XPM jali (weight not less than 4.0 kg/Sqm) with cast iron frame, funnel, with wire mesh, 20mm bore medium grade GI watering pipe, lugs, 15mm bore light grade GI protection pipe, test point, etc, incluidng taking down of old u/s earthing set complete all as specified and as directed. Note: (i) Item includes the cost of 7.5 m GI pipe for protection of earth lead. Any additional length shall be adjusted through deviation order. (ii) Item includes the cost of 7.5 m GI earth lead. Any additional in length shall be adjusted through deviation order ( For Main DBs ) (iii) Item includes the cost of Charcoal and commercial salt ( For Main DBs )

Sub main wiring with two run of 6.00 Sqmm (2x6 sqmm) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor confirming to IS-694 drawn through and including non-metalic PVC casing caping ISI marked with all accessories etc with one run of 6.00 Sqmm (1x6sqmm) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire and making good to match with existing surfaces including taking down of old sub main wirings complete all as specified and directed by Engineer-in-Charge. Note:- 2 runs of 6 Sqmm (2x6sqmm), one run of 6 Sqmm (1x6 sqmm) cable and one metre of PVC casing caping will be measured as one unit. Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB

Sub main wiring with two run of 4.00 Sqmm (2x4 sqmm) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor confirming to IS-694 drawn through and including non-metalic PVC casing caping ISI marked with all accessories etc with one run of 4.00 Sqmm (1x4sqmm) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire and making good to match with existing surfaces including taking down of old sub main wirings complete all as specified and directed by Engineer-in-Charge. Note:- 2 runs of 4 Sqmm (2x4sqmm), one run of 4 Sqmm (1x4 sqmm) cable and one metre of PVC casing caping will be measured as one unit. Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB

S&F in replacment LED lights fitting, TITANIA SLEEK NEW T5 LED TUBELIGHT (DOUBLE SIDE CONNECTION) (Double side Connection), 1x18/20 watt, 220 volts, AC ultra bright LED tube light with aluminium heat sink & polycarbonate diffuser having high efficacy suited for installation in existing T5 fitting with G5 lamp holders, led driver outside decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. Make : Cat part No TITANIASLEEK1149T5DSTL18WLED865SPC of Havells/ Philips/Bajaj/ Crompton

Supply and Fixing in replacement of LED Mirror light fitting of 09/10 watts capacity and type 230 volts box type , with standard specification etc complete with all accessories pre wired twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed by Engr in Charge. MAKE: Cat part No LHEXBLP7IN1W009 of Havells or equal approved in Bajaj/Philips/Syska

S&F in replacment of round shape 15 Watt t, 220 volts, AC recessed type with high effciency PMMA diffuser soft glare free light complete with driver, holder including LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-Charge. Make : Havells/ Philips/Bajaj/ Crompton

S&F in replacement of LED cool white/warm white surface mounted concealed type walk over light 24 watt, 220 volts, complete all as specified and directed by Engr-in-Charge. Make : Havells/ Philips/Bajaj/ Crompton

S&F in replacement of LED lamp 7 Watt, 230 V, mounting on wall and ceiling complete all as specified and directed by Engr-in-Charge. Make : Havells/ Philips/Bajaj/ Crompton

Supply and fixing of exhaust fan, plastic body, AC single phase 230 volts of size 250 mm sweep with blades and frame and louvers complete all as specified and as directed.

SSV Infra