Supply and installation of furniture, at UHBVN, Head Office Building, IP-3 and 4, Sector-14, Panchkula

Amount

ST1L Side Table for T1L 1400 X 700 Included in Table price

T1 R Chairman Cabin Table 2800 X 1000 X 750

ST1R Side Table for T1R 1400 X 700 Included in Table price

Providing & Placing table & side storage with Material of Construction: 1) The table shall be made of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm. All external shall be Veneer finish and internal shall be laminate finish. 2)The Modesty panel shall be veneer finish on both side & fixed to the unit . 3)Veneer: 4 mm thick teak Veneer 4) Lipping: matching PVC/ABS edge band on all edges. 5) The unit shall have Height Adjustable top with height range from 720– 1180mm approximately, With Up/Down Controller that adjusts height of desk by simply pushing the up and down controller at the rate of 30 mm per second (basic) and 38 mm per second (extended), Rectangular/Round Leg, Table top Veneer, With upper cable tray, with cable housing connect with understructure leg,with cable chain connected with cable housing help to pass wire from floor to upper cable tray within the height range. 6) Polishing: PU polish on all veneer and wooden surfaces as per sample . 7) One gormet for CPU Unit with cable organizer on top & Provision for wiring and switch board. 8)Laminate finish Adjustable shelves. 9)Hardware: - Hinges: Auto close Hinges for open able shutters. - Soft close premium Channel for drawers: Quadro or equivalent as by Architect/EIC from make list (hettich) - One multipurpose lock per active shutter and drawer of make - Handle/Knob: of SS 304 grades or Aluminum finish profile handle. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3. T2L Director Cabin Table 2400 X 900 X 750

ST2L Side Table for ST2L 1200 X 700 Included in Table price

T2R Cabin Table (DHBVN) 2400 X 900 X 750

ST2R Side Table for ST2R 1200 X 700 Included in Table price

Providing & Placing table with Material of Construction: 1) Table top shall be made up of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm. + laminate finish of make and shade . 2) Supporting frame for table top & leg shall be fabricated in MS hollow box section and powder coated as per make, shade and quality. 3) Modesty Panel shall be made of 1mm thick perforated MS epoxy powder coated sheet of make and shade with MS frame work supported with distance pin on supports, as per reference drawing and sample . 4) The side storage unit shall have multiplue Shutters(openable & sliding) & open space as per the reference images.All External & Internal box work shall be Laminate finish. 5) Lipping: matching PVC/ABS edge band on all edges. 6) One gormet for CPU Unit with cable organizer on top & Provision for wiring and switch board. 7) 75mm Dia powder coated MS Pipe support fixed witht the table top. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3 . T3L Chief,SE Cabin 2400 X 900 X 750

ST3L Side Table for ST3L 550 X 1800 X 600 Included in Table price

T3R Chief,SE Cabin 2400 X 900 X 750

ST3R Side Table for ST3R 550 X 1800 X 600 Included in Table price

Providing & Placing table with Material of Construction: 1) Table top shall be made up of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm.+ laminate finish of make and shade . 2) Supporting frame for table top & leg shall be fabricated in MS hollow box section and powder coated as per make, shade and quality. Support beam shall be made up of steel tube and sheet metal, features with Rubber Noise dampening, Intermediate leg cover shall be 1.5mm metal or 6mm PET, secured to a metal bracket. 3) The Cable Tray shall be made up of 1.5mm thick metal & shall be supported with a 1.2mm metal structure that feature 3mm metal hooks and cover (for end-of-run application) With Vertical riser to uptake wiring from floor to flipper to access the Switch plat. 4) The side storage unit shall have multiplue Shutters(openable & sliding) & open space as per the reference images.All External & Internal box work shall be Laminate finish. 5) Lipping: matching PVC/ABS edge band on all edges. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3. T4L PA,Xen Cabin Table 1800 X 750 X 750

ST4L Side Table for ST4L 400 X 1800 X 600 Included in Table price

T4R PA,Xen Cabin Table 1800 X 750 X 750

ST4R Side Table for ST4R 400 X 1800 X 600 Included in Table price

Providing & Placing table & side storage with Material of Construction: 1) Table top shall be made up of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm. + laminate finish of make and shade . 2) Intermediate leg shall be made up of steel tube and sheet metal and powder coated as per the sample. 3) Cable Tray shall be made up of 1.5mm thick metal & supported with a 1.2mm metal structure that feature 3mm metal hooks and cover (for end-of-run application) with Vertical riser to uptake wiring from floor to flipper to aceess the Switch plate. 4) The side storage unit shall have multiplue Shutters(openable & sliding) & open space as per the reference images.All External & Internal box work shall be Laminate finish. 5) Desk divider cum soft board with fabric shall be fixed with the Clamp on the table as per the reference drawing. 6) Heavy Duty Self Adjusting table base Levelers shall be fixed at the bottom of metal legs. 7) Lipping: matching PVC/ABS edge band on all edges. Hardware: - Premium Soft close sliding track for shutter. - Hinges: Auto close Hinges for open able shutters of make. - One multipurpose lock per active shutter and drawer of make - Handle/Knob: of SS 304 grades or Aluminum finish profile handle. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3. T5L L - Workstation 1500 X 600 X 750

ST5L Side Table for ST5L 400 X 1500 X 600 Included in Table price

T5R L - Workstation 1500 X 600 X 750

ST5R Side Table for ST5R 400 X 1500 X 600 Included in Table price

DD1 Desk Divider for T5L & T5R 900 X 19 X 450

Providing & Placing table & side storage with Material of Construction: 1) Table top shall be made up of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm + laminate finish of make and shade . 2) Supporting frame for table top & leg shall be fabricated in MS hollow box section and powder coated as per make, shade and quality. Support beam shall be made up of steel tube and sheet metal, features with Rubber Noise dampening, Intermediate leg cover shall be 1.5mm metal or 6mm PET, secured to a metal bracket. 3) The Cable Tray shall be made up of 1.5mm thick metal & shall be supported with a 1.2mm metal structure that feature 3mm metal hooks and cover (for end-of-run application) With Vertical riser to uptake wiring from floor to flipper to access the Switch plat. 4) The side storage unit shall have multiple Shutters(openable & sliding) & open space as per the reference images. All External & Internal box work shall be Laminate finish. 5) Lipping: matching PVC/ABS edge band on all edges. POWER COMMUNICATION • A hardwire utility package shall be attached to the inside of the cable tray to provide accessible power and communication to table occupants through the flip-up doors. • Tray accommodates either one or two hardwire utility packages. • Length of utility package determines number of socket punchouts • Socket punchouts are from India Socket type. • Workstation Screen Tackable fabric screen size: 1500W 450HT Including necessary Bracket to fix above worksurface The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3. T6L L shape workstations 1200 X 600 X 750

ST6L Side Table for ST6L 350 X 1800 X 1200Included in Table price

T6R L shape workstation 1200 X 600 X 750

ST6R Side Table for ST6R 350 X 1800 X 1200 Included in Table price

DD2 Desk Divider for T6L & T6R 1200 X 19 X 600

Providing & Placing table with Material of Construction: 1) Table top shall be made up of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm + laminate finish of make and shade . 2) Supporting frame for table top & leg shall be fabricated in MS hollow box section and powder coated as per make, shade and quality. Support beam shall be made up of steel tube and sheet metal, features with Rubber Noise dampening, Intermediate leg cover shall be 1.5mm metal or 6mm PET, secured to a metal bracket. 3) The Cable Tray shall be made up of 1.5mm thick metal & shall be supported with a 1.2mm metal structure that feature 3mm metal hooks and cover (for end-of-run application) With Vertical riser to uptake wiring from floor to flipper to access the Switch plat. 4) The side storage unit shall have multiple Shutters(openable & sliding) & open space as per the reference images. All External & Internal box work shall be Laminate finish. 5) Lipping: matching PVC/ABS edge band on all edges. POWER COMMUNICATION • A hardwire utility package shall be attached to the inside of the cable tray to provide accessible power and communication to table occupants through the flip-up doors. • Tray accommodates either one or two hardwire utility packages. • Length of utility package determines number of socket punchouts • Socket punchouts are from India Socket type. • Workstation Screen Tackable fabric screen size: 1500W 450HT Including necessary Bracket to fix above worksurface The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3. T7 Regular workstation 1200 X 600 X 750

DD3 Desk Divider for T7 900 X 19 X 450

T8 Reception Table 2700 X 1550 X 1050 Providing, making, fixing and positioning reception table of size 2700 (L) x 1550 (B) x 1050 (H). Material of construction: 1) The Table top, front, side & back shall be made up of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm (Corian/ LG/ Staron/Hanex/samsung ) as per colour shall be fixed with Adhesive as mentioned in the reference drawing. 2) Lower unit shall have multiple drawer on both side, all external shall be solid acrylic surface finish and all internal shall be laminate finish. 3) Provision for the led neon light as per the reference drawing. 4) Polish:High Gloss polish of solid surface no joint shall be visible. 3) Hardware: - -Soft close premium Channel for drawers: Quadro 600 to 800 mm or equivalent as by Architect/EIC from make list (hettich) - Handle: 150 mm long Solid rod "D" shaped handle of SS 304 grades - One multipurpose lock per active shutter of make - Two gormet for CPU Unit with cable organizer on top & Provision for wiring and switch board. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site.

T9 Cash Counter 2100 X 750 X 1050 Providing, making, fixing and positioning cafeteria counter table of size 2100 (L) x 750 (B) x 1050 (H). Material of construction: 1) The Table top with multiple drawer, front, side & back shall be made up of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm (Corian/ LG/ Staron/Hanex/samsung ) as per colour shall be fixed with Adhesive as mentioned in the reference drawing. 2) Polish:High Gloss polish of solid surface no joint shall be visible. 3) Hardware: - -Soft close Channel for drawers: Quadro 600mm or equivalent as by Architect/EIC from make list (hettich) - Handle: 150 mm long Solid rod "D" shaped handle of SS 304 grades - One multipurpose lock per active shutter of make - Two gormet for CPU Unit with cable organizer on top & Provision for wiring and switch board. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site.

ST8 Side table behind T9 2100 X 400 X 750 Providing, making and fixing storage units in position Storage Unit Size : 2100 x 400 x 750 mm as per reference drawings. 1) The Box work,shutter and shelves shall be made of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm + laminate finish beading all around. 2) Backing of storage shall be made from 12mm thick BWP ply. 3) Laminate of make and shade on External & internal surface, both side of shelves & back side of unit. 4) Lipping: matching PVC/ABS edge band on all edges. 5) Polishing: water base PU polish on all veneer and wooden surfaces. 6) Hardware: - Hinges: Auto close Hinges for open able shutters of make for open able shutters - Minumum 3 hinges per shutter. - One multipurpose lock per active shutter and drawer of make - Tower bolt: Brass satin finish nickel plated or SS 304 150 mm long for upper shutters. - Handle: SS handle 150 mm or Aluminum finish conceal profile handle as per the sample . - Adjustable shelves. Onsite measurement for storages, etc. shall be taken before manufacturing it. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3.

T10 Cafeteria Table 1800 X 900 X 750 Providing, making, fixing and positioning cafeteria table with Material of Construction: 1) Table top shall be made up of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm + laminate of make and shade beading on all the visible sides of ply edges. 2) Supporting framing for table top & leg shall be fabricated in 50 x 25 x 2.6 mm CRS polished MS hollow box section powder coated frame as per make, shade and quality. 3) Lipping: matching PVC/ABS edge band on all edges. 4) Heavy Duty Self Adjusting Levelers shall be fixed at the bottom of metal legs The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3.

T11 Cafeteria Table 1000 dia X 750 Providing, making, fixing and positioning cafeteria table with Material of Construction: 1) Table top shall be made up of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm + laminate of make and shade beading on all the visible sides of ply edges. 2) Supporting framing for table top & leg shall be fabricated in 10mm thick Metal Plate Base & pole size is 60mmx1.6 CRS polished MS hollow box section powder coated frame as per make, shade and quality. 3) Lipping: matching PVC/ABS edge band on all edges. 4) Heavy Duty Self Adjusting Levelers shall be fixed at the bottom of metal legs The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3.

T12 Cafeteria Table 750 X 750 X 750 Providing, making, fixing and positioning cafeteria table with Material of Construction: 1) Table top shall be made up of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm + laminate of make and shade beading on all the visible sides of ply edges. 2) Supporting framing for table top & leg shall be fabricated in 10mm thick Metal Plate Base & pole size is 50mm CRS polished MS hollow box section powder coated frame as per make, shade and quality. 3) Lipping: matching PVC/ABS edge band on all edges. 4) Heavy Duty Self Adjusting Levelers shall be fixed at the bottom of metal legs The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3.

T13 Meeting Table 1200 dia X 750 Providing, making, fixing and positioning meeting table with Material of Construction: 1) Table top shall be made up of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm + laminate of make and shade beading on all the visible sides of ply edges. 2) Supporting framing for table top & leg shall be fabricated in 10mm thick Metal Plate Base & pole size is 60mmx1.6 CRS polished MS hollow box section powder coated frame as per make, shade and quality. 3) Flipper at worksurface for electrical point access.Wire passing from floor to pole to double decker, have utility package where switch plate can accommodate. 4) Lipping: matching PVC/ABS edge band on all edges. 5) Heavy Duty Self Adjusting Levelers shall be fixed at the bottom of metal legs The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3.

T14 Meeting Table 2400 X 1200 X 750 Providing, making, fixing and positioning meeting table with Material of Construction: 1) Table top shall be made up of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm + laminate of make and shade beading on all the visible sides of ply edges. 2) Supporting framing for table top & leg shall be fabricated in chrome/Powder coated finish section as per make, shade and quality. 3) Flipper at worksurface for electrical point access.Wire passing from floor to pole to double decker, have utility package where switch plate can accommodate. 4) Lipping: matching PVC/ABS edge band on all edges. 5) Heavy Duty Self Adjusting Levelers shall be fixed at the bottom of metal legs The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3.

T15 Meeting Table 1300 X 2700 X 750 Providing, making, fixing and positioning meeting table with Material of Construction: 1) Table top shall be made up of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm + laminate of make and shade beading on all the visible sides of ply edges. 2) Supporting framing for table top & leg shall be fabricated in chrome/Powder coated finish section as per make, shade and quality. 3) Flipper at worksurface for electrical point access.Wire passing from floor to pole to double decker, have utility package where switch plate can accommodate. 4) Lipping: matching PVC/ABS edge band on all edges. 5) Heavy Duty Self Adjusting Levelers shall be fixed at the bottom of metal legs The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3.

T18 Scada Table 3300 X 600 X 750 Providing, making, fixing and positioning scada table. Material of Construction: 1) Table top shall be made up of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm + laminate of make and shade beading on all the visible sides of ply edges. 2) Supporting framing for table top & leg shall be fabricated in SS 304 grade material. 3) Flipper at worksurface for electrical point access.Wire passing from floor to pole to double decker, have utility package where switch plate can accommodate. 4) Lipping: matching PVC/ABS edge band on all edges. 5) Heavy Duty Self Adjusting Levelers shall be fixed at the bottom of metal legs The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3.

T19 Director Dining Table 600 dia X 750 Providing, making, fixing and positioning MD UHBVN Dining table. Material of Construction: 1) Table top shall be made up of ply/engineering wood / PLB /MDF material + laminate of make and shade beading on all the visible sides of ply edges. 2) Supporting framing for table top & leg shall be fabricated in 10mm thick Metal Plate Base & pole size is 75 mm 1.6 CRS polished MS hollow box section powder coated frame as per make, shade and quality. 3) Lipping: matching PVC/ABS edge band on all edges. 4) Heavy Duty Self Adjusting Levelers shall be fixed at the bottom of metal legs The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3.

T20 Chairman Dining Table 1000 dia X 750 Providing, making, fixing and positioning MD UHBVN Dining table. Material of Construction: 1) Table top shall be made up of ply/engineering wood / PLB /MDF material + laminate of make and shade beading on all the visible sides of ply edges. 2) Supporting framing for table top & leg shall be fabricated in 10mm thick Metal Plate Base Dia size & pole size is 75 mm 1.6 CRS polished MS hollow box section powder coated frame as per make, shade and quality. 3) Lipping: matching PVC/ABS edge band on all edges. 4) Heavy Duty Self Adjusting Levelers shall be fixed at the bottom of metal legs The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3.

Providing and placing of Rectangular TableTop : Material of Construction: 1) Table top shall be made up of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm + laminate of make and shade beading on all the visible sides of ply edges. 2) Supporting framing for table top & leg shall be fabricated in SS 304 grade material. 3) Lipping: matching PVC/ABS edge band on all edges. 4) Heavy Duty Self Adjusting Levelers shall be fixed at the bottom of metal legs The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3. ST9 Cabins,Common Area Side Table 600 X 600 X 550

ST10 Cabins,Common Area Side Table 400 X 600 X 550

ST11 Cabins,Common Area Side Table 400 dia X 550 Providing, making, fixing and positioning cafeteria table. Material of Construction: 1) Table top shall be made up of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm + laminate of make and shade beading on all the visible sides of ply edges. 2) Supporting framing for table top & leg shall be fabricated in Ø12mm transmission metal profile making a cross base structure by band and welding. Size 400 dia x 550 mm section powder coated frame as per make, shade and quality. 3) Lipping: matching PVC/ABS edge band on all edges. 4) Glide as per the floor finish. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3.

ST13 Sixth Floor Waiting Area Side Table 600 dia X 550 Providing, making, fixing and positioning cafeteria table. Material of Construction: 1) Table top shall be made up of ply/engineering wood / PLB /MDF material + Decowood veneer of make and shade. 2) Supporting framing for table top & leg shall be fabricated in 15 mm x15 mm x1.6G in stainless steel pvd coating as per make, shade and quality. 3) Lipping: matching PVC/ABS edge band on all edges. 4) Heavy Duty Self Adjusting Levelers shall be fixed at the bottom of metal legs The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3.

ST16 MD,Director Cabin Side Table 400 dia X 550

CT1 Conference, Sixth Floor Waiting Centre Table 1000 X 600 X 550 Providing, making, fixing and positioning side table with: Material of Construction: 1) The top shall be made of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm painted in polyurethane. 2) Supporting frame & leg of the table shall be crafted in lacquered aluminum material. 3) Glides: High quality glides of make shall be used. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site.

CT3 Chairman Cabin Centre Table 800 X 600 X 550 Providing, making, fixing and positioning centre table with Material of Construction: 1) Table top shall be made up of ply/engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm + veneer of make and shade. 2) Supporting framing for table top & leg shall be fabricated in 15 mm x15 mm x1.6G in stainless steel pvd coating as per make, shade and quality. 3) Lipping: matching PVC/ABS edge band on all edges. 4) Heavy Duty Self Adjusting Levelers shall be fixed at the bottom of metal legs The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. Must meet or exceed the product emission testing following ANSI/BIFMA e3 Furniture Sustainability Standard criteria 7.6.1, 7.6.2 and 7.6.3.

T4T Trolley 415 X 375 X 550 Providing & Placing Regular Metal pedestal size 415 x 375 x 550 mm. Material of Construction: Metal pedestal trolley 1 BOX, 1 FILE with lock. standard castor and 1 additional central castor to prevent tipping and built in anti tipping mechanism that allows only one drawer to be open. Drawer Pedestal having 2 drawers with framework made up of MS with 50-50 micron powder coating of shade sections of 16 gauge MS sections and 55 micron thick powder coating of make and shade, central 10 lever cam lock and anti rebound mechanized drawer channels as per specified item's manufacturer's specifications. The rate shall be in Nos for all floors and at all heights including all costs. Sample shall be got by Architect and EIC.

CHAIR C1A Chairman Chair- Providing and Placing chair with Typology : High Back Chair 1. Adjustable Back allows to move up and down movement only with seat size 510x500m back size 530x685mm. 2. Seat depth adjusts 70mm by rotating dial while seated for an easy fine-tuned fit. 3. Seat angle passively adjusts in a range from -1° to +3°. 4. Passive seat edge angle flexes 39mm, relieving pressure under the user’s thighs 5. Variable back stop. To lock backrest in upright position, lean forward and flip lever down. Flip lever up to unlock for full-range motion. There are four settings to give just the right angle of reclines. 6. Lumbar height adjusts 102mm (134mm to 235mm) from seat by grabbing exposed tabs and sliding the lumbar support up or down. 7. Headrest adjust 127mm vertically 102mm forward and backward and pad rotates 90˚ degrees. 8. 360˚-arm. The 360˚ provide a great dimensional range for large users and many postures, and ensures proper support when using a range of technology, mobile or fixed. 9. Arm width adjusts parallel 156mm per arm for a total range of 258mm to 572mm between arms 10. Arm height adjusts independently 105mm (181mm H to 293mm H) 11. Arm pivot independently 15˚ inward and 15˚ outward. Grasp arm and push front to left or right. 12. Arm depth adjusts 54mm to enable user to get closer to worksurface. 13. With Headrest 14. Mechanisms, pneumatic cylinders, arm caps, foam, glides and casters have a 5 year warranty.

C2A Director Chair- Providing and Placing chair with Typology : Medium Back Chair 1. Parallel slats in the LiveBack shell provide extensive flexibility to allow back to conform to individual users. 2. Rectilinear arms with soft caps. 3. Seat height adjusts pneumatically. Range of adjustability is 127mm, from 394mm H to 521mm H. 4. Passive seat edge angle flexes 39mm, relieving pressure under the user's thighs. 5. Seat depth adjusts 77mm (401mm to 477mm) by pulling handle up. 6. Lumbar height adjusts 127mm (134mm to 261mm from seat) 7. Lower back firmness adjusts by turning knob two complete turns. Forward increases firmness. Backward decreases firmness. 8. Arm height adjusts independently within a range of 102mm (178mm to 280mm from the seat). 9. Arm width adjusts 58mm each independently 10. Arm depth adjusts approximately 77mm to enable user to get closer to worksurface. 11. With Headrest 12. Mechanisms, pneumatic cylinders, arm caps, foam, glides and casters have a 5-year warranty.

C3A Chief,SE Chair Providing and Placing chair with Typology : Medium Back Chair 1.Adjustable Back allows to move up and down movement only with seat size 515x495mm back size 520x500mm 2. Advanced weight-activated mechanism with a natural fluid motion 3. Comfort dial has four settings that allow for the user’s personal preference and work style. 4. Rectilinear arms with soft caps are standard. 5. Seat height adjusts pneumatically. Standard range of adjustability is 127mm from 420mm H to 547mm H. 6. Seat depth adjusts 64mm (394mm to 458mm) by pulling handle up. Slide seat forward or back to accommodate various leg lengths. Release handle to lock. to decrease 7. Lumbar height adjusts 108mm (153mm to 261mm) from seat) by grabbing exposed tabs and sliding the lumbar support up or down. 8. Comfort Dial has four settings: (1) weight-activated setting; (2) boosted setting that has approximately 20% more resistance than your body is providing; (3) mid stop recline setting; and (4) an upright setting. 9. Rectilinear height, width, pivot-, and depth-adjustable arms 10. Arm height adjusts independently within a range of 102mm (178mm to 280mm from the seat) 11. Arm width adjusts 58mm each, 115mm overall. Grasp arm and move in or out. 12. Arm pivot independently 30˚ inward and outward. 13. Arm depth adjusts by sliding arm caps back 77mm. Friction-fit mechanism keeps arm in position. 14. With Headrest. 15. Mechanisms, pneumatic cylinders, arm caps, foam, glides and casters have a 5 year warranty.

C5A Xen/PA/Sr.AO Chair - Providing and Placing chair with Typology : High Back Chair H-1140-1310mm D-760mm W-760mm 1. Synchro-tilt mechanism on work chairs keeps users oriented to their work. 2. Seat height adjusts pneumatically. Range of adjustability is 127mm, from 444mm H – 564mm H 3. Seat depth adjusts 50mm by pulling handle up. Slide seat forward or back to accommodate various leg lengths. 4. Lumbar height adjusts 50mm by grabbing and sliding the lumbar support up or down. 5. Upright back lock allows users to lock the back rest in an upright position. 6. Height-, pivot-, and depth-adjustable arms 7. Arm height adjusts independently within a range of 65mm (195mm to 260mm). 8. Arms pivot 5 degrees inwards and 15 degrees outwards on models with adjustable arms. 9. With Headrest 10.Upholstered back of chairs mesh at back.

C6 Workstation Chair Providing and Placing chair with Typology : Medium Back Chair H-965-1140mm D-760mm W-760mm 1. Synchro-tilt mechanism on work chairs keeps users oriented to their work. 2. Seat height adjusts pneumatically. Range of adjustability is 127mm, from 444mm H – 564mm H 3. Seat depth adjusts 50mm by pulling handle up. Slide seat forward or back to accommodate various leg lengths. 4. Lumbar height adjusts 50mm by grabbing and sliding the lumbar support up or down. 5. Upright back lock allows users to lock the back rest in an upright position. 6. Height-, pivot-, and depth-adjustable arms 7. Arm height adjusts independently within a range of 65mm (195mm to 260mm). 8. Arms pivot 5 degrees inwards and 15 degrees outwards on models with adjustable arms. 9. Without Headrest 10.Upholstered back of chairs mesh at back.

C7 Reception & 6th floor waiting Chair - Providing and placing of Arm chair with Seat Size -460x450mm Back size- 465x480mm (H) 1)The Arm Chair shall be Leatherette / fabric upholstered seat & back with metal legs in powder coat finish. 2)The Seating shall be made of Ply (ISI Marked) and Consists of required Density PU Foam 3)Understructure :Framing and Legs in Metal powder coated as per the shade. 4) Glides: High quality glides of make shall be used. 5) All joinery and detailing shall be as per the reference images or design pattern. 6) Fabric Tapestry

C-8 Cafeteria Bench- Providing and placing of Seating unit size Size : 1500x400x450H mm 1)The Seating shall be made of Ply (ISI Marked) and Consists of 32 & 40 Density PU Foam 2)Understructure :Framing and Legs in Metal 50x25x1.6G Tube and 25mm Dia x 1.6g Pipe powder coated as per the shade. 3) Glides: High quality glides of make shall be used. 4) All joinery and detailing shall be as per the reference images or design pattern.

C9 Cafeteria Chair Providing and placing of General-Purpose Office Chairs with Seat size 435x455mm Back Size - 450x390mm Should be multi-use chair that offers affordable style and comfort in a lightweight stackable design. Ideal for cafés, seminar rooms, team and training spaces, and everywhere in-between. Quick connect glides lock the chairs together to form rows. 1. Silver or Black frame 2. Quick connect feet to group chairs together 3. Stacks up to 8 chairs high on the floor 4) Glides: High quality glides of make shall be used. 5) All joinery and detailing shall be as per the reference images or design pattern. 6) Fabric Chrome Stand

C10 Kitchen Stool Providing and Placing Polypropyelene bar stool Seat Height 750mm with Dimensions 470W x 520D x 1000h. Sh:660mm with 1) Chair with solid teak/beech wood exposed frame structure. 2) Polypropyelene Moulded chair. 3) Solid wood legs that visually tie with the framed look of the chair. 4) Polishing: PU polish on all wooden surfaces. 5) Glides: High quality glides of make shall be used. 6) All joinery and detailing shall be as per the reference images or design pattern.

C11 Dispensary bench Providing and Placing 2 seat Tandem Seating as per reference images with Size Approximately 1180 x 755 mm Seat & Back : metal chrome finish Beam : Steel powder coated Arm & Leg : Die cast Aluminum/ Chrome finish Bracket : Die cast Aluminum/ Chrome finish Weight Handling Capacity shall be 225-250 Kg.

C12 Patient Stool Providing and Placing of Round Stool with The stool shall be Height Adjustible round stool in chrome finish material. Leatherette cushion Seat upholstery.

C13 Passage Chair Providing and Placing of Library Chair with 1)Foam Density 33Kg/m3. The Chair Back profile should be of Bent Plywood . Chair should be padded with Foam on Seat and Back and on sides also for user comfort for long hours of Seating. Legs to be made of Solid Rubberwood. 2) Polishing: PU polish on all wooden surfaces. 3) Glides: High quality glides of make shall be used. 4) All joinery and detailing shall be as per the reference images or design pattern.

C15 Peon Stool Providing and supplying the bar stool chair with 1) Stool shall be made of die cast Aluminum frame satin finish frame structure and moulded seat cum Leatherette cushioned Seat Upholstery as per the reference images. 2) Glides: High quality glides of make shall be used. 3) All joinery and detailing shall be as per the reference images or design pattern.

C16A Conference Chair Providing and Placing chair with Typology : Medium Back Chair 1. Adjustable Back allows to move up and down movement only with seat size 515x495mm back size 520x500mm. 2. Advanced weight-activated mechanism with a natural fluid motion 3. Comfort dial has four settings that allow for the user’s personal preference and work style. 4. Rectilinear arms with soft caps are standard. 5. Seat height adjusts pneumatically. Standard range of adjustability is 127mm from 420mm H to 547mm H. 6. Seat depth adjusts 64mm (394mm to 458mm) by pulling handle up. Slide seat forward or back to accommodate various leg lengths. Release handle to lock. to decrease 7. Lumbar height adjusts 108mm (153mm to 261mm) from seat) by grabbing exposed tabs and sliding the lumbar support up or down. 8. Comfort Dial has four settings: (1) weight-activated setting; (2) boosted setting that has approximately 20% more resistance than your body is providing; (3) mid stop recline setting; and (4) an upright setting. 9. Rectilinear height, width, pivot-, and depth-adjustable arms 10. Arm height adjusts independently within a range of 102mm (178mm to 280mm from the seat) 11. Arm width adjusts 58mm each, 115mm overall. Grasp arm and move in or out. 12. Arm pivot independently 30˚ inward and outward. 13. Arm depth adjusts by sliding arm caps back 77mm. Friction-fit mechanism keeps arm in position. 14. With Headrest. 15. Mechanisms, pneumatic cylinders, arm caps, foam, glides and casters have a 5 year warranty. Chair to be warranted for users up to 181 Kg (400 lbs).

C 16B Conference Chair Providing and Placing chair with Typology : Medium Back Chair 1. Adjustable Back allows to move up and down movement only with seat size 515x495mm back size 520x500mm 2. Advanced weight-activated mechanism with a natural fluid motion 3. Comfort dial has three settings that allow for the user’s personal preference and work style. 4. Seat height adjusts pneumatically. Standard range of adjustability is 127mm from 420mm H to 547mm H. 5. Seat depth adjusts 64mm (394mm to 458mm) by pulling handle up. 6. Lumbar height adjusts 108mm (153mm to 261mm) from seat) by grabbing exposed tabs and sliding the lumbar support up or down. 7. Comfort Dial has three settings: (1) weight activated setting; (2 boosted setting that has more resistance than your body is providing; (3) an upright back lock setting. 8. Arm height adjusts independently within a range of 127mm (165mm to 292mm from the seat). 9. Arm width adjusts 51mm each, 102mm overall. Grasp arm and move in or out. 10. Arm pivot independently 40˚ inward and outward. Grasp arm and push front to left or right. 11. Arm depth adjust by sliding arm caps back 76mm. Friction-fit mechanism keeps arm in position. 12. Without Headrest 13. Mechanisms, pneumatic cylinders, arm caps, foam, glides and casters have a 5-year warranty. Chair support 181 Kg (400 lbs) with no loss in performance.

C17 Reception Chair Providing and Placing chair with Typology : Medium Back Chair H-965-1140mm D-760mm W-760mm 1. Synchro-tilt mechanism on work chairs keeps users oriented to their work. 2. Seat height adjusts pneumatically. Range of adjustability is 127mm, from 444mm H – 564mm H 3. Seat depth adjusts 50mm by pulling handle up. Slide seat forward or back to accommodate various leg lengths. 4. Lumbar height adjusts 50mm by grabbing and sliding the lumbar support up or down. 5. Upright back lock allows users to lock the back rest in an upright position. 6. Height-, pivot-, and depth-adjustable arms 7. Arm height adjusts independently within a range of 65mm (195mm to 260mm). 8. Arms pivot 5 degrees inwards and 15 degrees outwards on models with adjustable arms. 9. Without Headrest 10.Upholstered seat & mesh back chairs .

C18 Director Cabin Dining Chair Providing and Placing Dining chair Moulded Arm chair with seat upholstered in leatherette/standard fabric 1) Chair with solid teak/beech wood exposed frame structure. 2) Moulded armchair Fully upholstered cushioned seat, back & side. 3) Solid wood legs that visually tie with the framed look of the chair. 4) Polishing: PU polish on all wooden surfaces. 5) Lining/upholstery work: - The stitching work shall be as per the design and pattern. Ergonomic required Density Latex foam & polyurethane foam shall be used in Back and seat of the unit. Top layer shall be of polyester fibre 130 GSM to 150 GSM or as per required comfort level. The whole assembly to be covered “Madarpat” and on it tapestry of make and shade to be fixed. 6) Glides: High quality glides of make shall be used. 7) Welt / trim detail all along the wood frame. 8) All joinery and detailing shall be as per the reference images or design pattern.

C19 Chairman Cabin Dining Chair Providing and Placing Dining chair with seat upholstered in leatherette/standard fabric 1) Chair with solid teak/beach wood exposed frame structure. 2) Fully upholstered cushioned seat, back & side. 3) Solid wood legs that visually tie with the framed look of the chair. 4) Polishing: PU polish on all wooden surfaces. 5) Lining/upholstery work: - The stitching work shall be as per the design and pattern. Ergonomic required Density Latex foam & polyurethane foam shall be used in Back and seat of the unit. Top layer shall be of polyester fibre 130 GSM to 150 GSM or as per required comfort level. The whole assembly to be covered “Madarpat” and on it tapestry of make and shade to be fixed. 6) Glides: High quality glides of make shall be used. 7) Welt / trim detail all along the wood frame. 8) All joinery and detailing shall be as per the reference images or design pattern.

C21 Recliner Chair Providing and Placing of Single Seater Sofa with Overall Dimensio 790W X 930D X 1020H. Made from abrasion resistant , wrinkle resistant , stain resistant Polyster Fabric . Seat Foam :- 112 mm thickness ( 3layer) of slab stock foam of varying densities 27, 32, 16 kg/m3, Back foam :- 12 mm thick slabstock foam of density 16 kg/m3 along with 1200 G Recron for superior comfort level, Cushion Armrest foam : 120 G of Recron filling 25 mm slabstock of density 27kg/m3 . Number of S Spring - 3, Thickness of S Spring 3.8 mm , nylone webbing for additional seat support. width of nylone belt : 50mm. The OEM Should be having valid Factory Licence, ISO 9001:2015, ISO-14001:2015 , OHSAS- 18001:2007, Valid ISO 50001 certificates as per NABCB Guidelines and should be Member of BIFMA from the past 15 Years. The recliner chair must be aluminium based leatherite and gas lifted.

S2 Cabins,Common Area Sofa Size : 1500 W x 800 D x 750 H. Providing and Placing Sofa with 1) Two seater sofa fully upholstered front & back loose cushion. 2) Ply and wooden based frame structure as per the finishes. 3) Sofa Glides: High quality glides of make shall be used. 4) Outer body and inner body of sofa—medium weave. Inner seat plain upholstery to match outer body upholstery. 5) Lining/upholstery work: - The stitching work shall be as per the design and pattern. Sofa Spring or Madras spring to be fixed on framing work. Ergonomic required Density Latex foam & polyurethane foam shall be used in Back and seat of the unit. Top layer shall be of polyester fibre 130 GSM to 150 GSM or as per required comfort level. The whole assembly to be covered “Madarpat” and on it tapestry of make and shade to be fixed. 6) The seat shall have removable covers. 7) Two throw cushion and it’s cover. 8) Woven small textured upholstery as per the sample . 9) All joinery and detailing shall be as per the reference images or design pattern. .

S3 Cabins,Common Area Sofa Size : 2000 W x 800 D x 750 H. Providing and Placing Sofa with 1) Three seater sofa fully upholstered front & back loose cushion. 2) Ply and wooden based frame structure as per the finishes. 3) Sofa Glides: High quality glides of make shall be used. 4) Outer body and inner body of sofa—medium weave. Inner seat plain upholstery to match outer body upholstery. 5) Lining/upholstery work: - The stitching work shall be as per the design and pattern. Sofa Spring or Madras spring to be fixed on framing work. Ergonomic required Density Latex foam & polyurethane foam shall be used in Back and seat of the unit. Top layer shall be of polyester fibre 130 GSM to 150 GSM or as per required comfort level. The whole assembly to be covered “Madarpat” and on it tapestry of make and shade to be fixed. 6) The seat shall have removable covers. 7) Throw cushion and it’s cover. 8) Woven small textured upholstery as per the sample . 9) All joinery and detailing shall be as per the reference images or design pattern.

S4 Conference room Sixth Floor waiting Size : 1500 W x 800 D x 750 H Providing and Placing Sofa with 1) Two seater sofa fully upholstered front & back loose cushion. 2) Metal base legs as per the finishes. 3) Sofa Glides: High quality glides of make shall be used. 4) Outer body and inner body of sofa—medium weave. Inner seat plain upholstery to match outer body upholstery. 5) Lining/upholstery work: - The stitching work shall be as per the design and pattern. Sofa Spring or Madras spring to be fixed on framing work. Ergonomic required Density Latex foam & polyurethane foam shall be used in Back and seat of the unit. Top layer shall be of polyester fibre 130 GSM to 150 GSM or as per required comfort level. The whole assembly to be covered “Madarpat” and on it tapestry of make and shade to be fixed. 6) The seat shall have removable covers. 7) Two throw cushion and it’s cover. 8) Woven small textured upholstery as per the sample . 9) All joinery and detailing shall be as per the reference images or design pattern.

S5 Conference room Sixth Floor waiting Sofa Size : 2000 W x 800 D x 750 H. Providing and Placing Sofa with 1) Three seater sofa fully upholstered front & back loose cushion. 2) Metal base legs as per the finishes. 3) Sofa Glides: High quality glides of make shall be used. 4) Outer body and inner body of sofa—medium weave. Inner seat plain upholstery to match outer body upholstery. 5) Lining/upholstery work: - The stitching work shall be as per the design and pattern. Sofa Spring or Madras spring to be fixed on framing work. Ergonomic required Density Latex foam & polyurethane foam shall be used in Back and seat of the unit. Top layer shall be of polyester fibre 130 GSM to 150 GSM or as per required comfort level. The whole assembly to be covered “Madarpat” and on it tapestry of make and shade to be fixed. 6) The seat shall have removable covers. 7) Throw cushion and it’s cover. 8) Woven small textured upholstery as per the sample . 9) All joinery and detailing shall be as per the reference images or design pattern.

S7 Conference room Sofa S7 - 5300 L x 750 W x 900 H

S8 Conference room Sofa S8- 2400 L x 750 W x 900 H

S9 Director & MD DHBVN Cabin Sofa Size : 750 W x 800 D x 750 H. Providing and Placing Sofa with 1) Single seater sofa fully upholstered front & back loose cushion. 2) Metal base legs as per the finishes. 3) Sofa Glides: High quality glides of make shall be used. 4) Outer body and inner body of sofa—medium weave. Inner seat plain upholstery to match outer body upholstery. 5) Lining/upholstery work: - The stitching work shall be as per the design and pattern. Sofa Spring or Madras spring to be fixed on framing work. Ergonomic required Density Latex foam & polyurethane foam shall be used in Back and seat of the unit. Top layer shall be of polyester fibre 130 GSM to 150 GSM or as per required comfort level. The whole assembly to be covered “Madarpat” and on it tapestry of make and shade to be fixed. 6) The seat shall have removable covers. 7) Throw cushion and it’s cover. 8) Woven small textured upholstery as per the sample . 9) All joinery and detailing shall be as per the reference images or design pattern.

S10 Director & MD DHBVN Cabin Sofa Size : 2000 W x 800 D x 750 H. Providing and Placing Sofa with 1) Three seater sofa fully upholstered front & back loose cushion. 2) Metal base legs as per the finishes. 3) Sofa Glides: High quality glides of make shall be used. 4) Outer body and inner body of sofa—medium weave. Inner seat plain upholstery to match outer body upholstery. 5) Lining/upholstery work: - The stitching work shall be as per the design and pattern. Sofa Spring or Madras spring to be fixed on framing work. Ergonomic required Density Latex foam & polyurethane foam shall be used in Back and seat of the unit. Top layer shall be of polyester fibre 130 GSM to 150 GSM or as per required comfort level. The whole assembly to be covered “Madarpat” and on it tapestry of make and shade to be fixed. 6) The seat shall have removable covers. 7) Throw cushion and it’s cover. 8) Woven small textured upholstery as per the sample . 9) All joinery and detailing shall be as per the reference images or design pattern.

S11 Director Cabin Sofa Size : 800 W x 800 D x 750 H. Providing and Placing Sofa with 1) Single seater sofa fully upholstered front & back loose cushion. 2) Metal base legs as per the finishes. 3) Sofa Glides: High quality glides of make shall be used. 4) Outer body and inner body of sofa—medium weave. Inner seat plain upholstery to match outer body upholstery. 5) Lining/upholstery work: - The stitching work shall be as per the design and pattern. Sofa Spring or Madras spring to be fixed on framing work. Ergonomic required Density Latex foam & polyurethane foam shall be used in Back and seat of the unit. Top layer shall be of polyester fibre 130 GSM to 150 GSM or as per required comfort level. The whole assembly to be covered “Madarpat” and on it tapestry of make and shade to be fixed. 6) The seat shall have removable covers. 7) Two throw cushion and it’s cover. 8) Woven small textured upholstery as per the sample . 9) All joinery and detailing shall be as per the reference images or design pattern.

S12 Director Cabin Sofa Size : 800 W x 800 D x 750 H. Providing and Placing Sofa with 1) Single seater sofa fully upholstered front & back loose cushion. 2) Metal base legs as per the finishes. 3) Sofa Glides: High quality glides of make shall be used. 4) Outer body and inner body of sofa—medium weave. Inner seat plain upholstery to match outer body upholstery. 5) Lining/upholstery work: - The stitching work shall be as per the design and pattern. Sofa Spring or Madras spring to be fixed on framing work. Ergonomic required Density Latex foam & polyurethane foam shall be used in Back and seat of the unit. Top layer shall be of polyester fibre 130 GSM to 150 GSM or as per required comfort level. The whole assembly to be covered “Madarpat” and on it tapestry of make and shade to be fixed. 6) The seat shall have removable covers. 7) Two throw cushion and it’s cover. 8) Woven small textured upholstery as per the sample . 9) All joinery and detailing shall be as per the reference images or design pattern.

S13 Director Cabin Sofa Size : 1600 W x 800 D x 750 H. Providing and Placing Sofa with 1) Two seater sofa fully upholstered front & back loose cushion. 2) Metal base legs as per the finishes. 3) Sofa Glides: High quality glides of make shall be used. 4) Outer body and inner body of sofa—medium weave. Inner seat plain upholstery to match outer body upholstery. 5) Lining/upholstery work: - The stitching work shall be as per the design and pattern. Sofa Spring or Madras spring to be fixed on framing work. Ergonomic required Density Latex foam & polyurethane foam shall be used in Back and seat of the unit. Top layer shall be of polyester fibre 130 GSM to 150 GSM or as per required comfort level. The whole assembly to be covered “Madarpat” and on it tapestry of make and shade to be fixed. 6) The seat shall have removable covers. 7) Two throw cushion and it’s cover. 8) Woven small textured upholstery as per the sample . 9) All joinery and detailing shall be as per the reference images or design pattern.

S14 CMD Cabin Sofa Size : 800 W x 800 D x 750 H. Providing and Placing Sofa with 1) Three seater sofa fully upholstered front & back loose cushion. 2) Metal base legs as per the finishes. 3) Sofa Glides: High quality glides of make shall be used. 4) Outer body and inner body of sofa—medium weave. Inner seat plain upholstery to match outer body upholstery. 5) Lining/upholstery work: - The stitching work shall be as per the design and pattern. Sofa Spring or Madras spring to be fixed on framing work. Ergonomic required Density Latex foam & polyurethane foam shall be used in Back and seat of the unit. Top layer shall be of polyester fibre 130 GSM to 150 GSM or as per required comfort level. The whole assembly to be covered “Madarpat” and on it tapestry of make and shade to be fixed. 6) The seat shall have removable covers. 7) Throw cushion and it’s cover. 8) Woven small textured upholstery as per the sample . 9) All joinery and detailing shall be as per the reference images or design pattern.

S15 CMD Retiring Room Sofa Size : 730 W x 830 D x 1160 H. Providing and Placing Sofa with 1) Work Lounge features a swivel tablet surface. 2) Adjustable headrest with removable pillow insert for ergonomic sizing and comfort. 4) Meat Swivel base with auto-return feature.Metal construction in Powder coated finish as per the sample . 5) Lining/upholstery work: - The stitching work shall be as per the design and pattern. Ergonomic required Density Latex foam & polyurethane foam shall be used in Back and seat of the unit. Top layer shall be of polyester fibre 130 GSM to 150 GSM or as per required comfort level. The whole assembly to be covered “Madarpat” and on it tapestry of make and shade to be fixed. 6) Woven small textured upholstery as per the sample . 7) All joinery and detailing shall be as per the reference images or design pattern.

U5 MD UHBVN Cabin Modular Storage Unit :Size : 1242 X 400 X 1570 MM Providing, making and fixing partly open storage units with shutter in position as per reference drawings. 1) The Box work and shelves shall be made from 19 mm thick BWP IS 710 Grade ply /engineering wood / PLB /MDF material. 2) The Shutter shall be made of 19mm thick Veneer finish + PU finish polish as per the sample on shutter. 3) Backing of storage shall be made from 12mm thick BWP IS 710 Grade ply /engineering wood / PLB /MDF + Veneer finish on both side. 4) All internal surface, both side of shelves & back side of unit shall be veneer finish. 5) Veneer: 4 mm thick teak Veneer of make and shade shall be fixed at both sides & Top sides of unit with 6 mm thick lipping on the edges of ply/engineering wood / PLB /MDF. 6) Teak wood - 6 mm thick lipping on all ply edges.70 mm x 70 mm thick solid wood base as per reference drawings. 7) Polishing: water base PU polish on all veneer and wooden surfaces. 8) Hardware: - Hinges: Auto close Hinges for open able shutters of make for open able shutters - Minumum 3 hinges per shutter. - One multipurpose lock per active shutter and drawer of make - Tower bolt: Brass satin finish nickel plated or SS 304 150 mm long for upper shutters. - Push to Open Magnetic Latch- of make minimum 2 nos per active shutter - Adjustable shelves. Onsite measurement shall be taken before manufacturing it. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site.

U8 Wash Area Platform Providing, making, fixing and positioning wash area unit of size 3400 (L) x 550 (B) x 1675 (H) MM. (Modular) Material of construction: 1) The unit shall be made up of 19 mm thick BWP - IS 710 Grade ply /engineering wood / PLB /MDF/wood plastic composite material and over the plywood 12 mm thick Acrylic solid surface of make (Corian/ LG/ Staron/Hanex/samsung ) as per colour shall be fixed with Adhesive as mentioned in the reference drawing.No joint shall be visible. 2) Lower unit the counter shall have multiple wash basin made of solid acrylic surface finish with divider as per the reference drawing. metal fabrication in RHS/SHC as required for the support of the counter. 3) Provision for the multiple tap fixed per the reference drawing. 4) Mirror paneling of wall with 12mm BWP -IS 710 ply backing. 5) Polish:High Gloss polish of solid surface no joint shall be visible. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site.

N1 Reception Providing, making, fixing and positioning screen of size 4650 (L) x 2517 (H) MM. Material of construction: Providing, fabricating, assembling, erecting and fixing in position at all heights/all levels/all floors/all shapes & sizes with all leads using MS Rolled Steel flat 6 x 100 mm all confirming to latest relevant IS codes for the MS work complete in the situations described hereinafter and comprising as per the reference drawing: 1) Profile Cutting of components to required lengths/widths and shapes twisted; 2) Shaping, Smooth grinding / machining of edges / faces / all welding joints; 3) The rate shall include for powder coating as per the sample . 4) Veneer box Paneling on floor and ceiling, to support the MS flat as per the desired shape and size mentioned in the reference drawing. 5) Hardware: - All consumable hardware as per by Architect/EIC from make list Onsite measurement shall be taken before manufacturing it. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site.

N2 Cafeteria Jali Parttion:SIZE 2031 X 2517 MM Providing, making, fixing & fabricating MS Jali partition in position as per reference drawings. 1) The partition shall be made from 6mm x 19 mm Flat bar fabricated as per reference images in powder coated finish as per the shade . 2) The Flat bar shall be fixed to the MS frame of 35 mm x 35 mm SHS CRS section powder coated connected to the flooring and ceiling with metal Anchor faster as per the reference images. 3) Hardware: - All consumable hardware as per by Architect/EIC from make list Onsite measurement shall be taken before manufacturing it. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site.

N3 MD UHBVN Cabin Jali Parttion SIZE : 1425 X 2517 MM Providing, making and fixing Jali cum partition units in position as per reference drawings. 1) The partition shall be made from 19 mm thick BWR IS 710 grade ply 19 mm thick BWP IS 710 Grade ply /engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm & painted in enamel colour as per the shade . 2) The SS 304 grade sheet shall be 16 gauge cut out patterns shall be CNC Machine cut in computer as per the drawing and sample . 3) Solid wood frame work of 45 mm x 45 mm all around the jali partition. 4) Fixed to the floor and and ceiling with spacer as per the reference drawing. 6) Polish: Water base PU polish on all wooden surfaces. 7) Hardware: - All consumable hardware as per by Architect/EIC from make list Onsite measurement shall be taken before manufacturing it. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site.

N4 O.T.S L.H.S Jali Parttion:SIZE 4500 X 2760 MM Providing, making, fixing & fabricating MS Jali partition in position as per reference drawings. 1) The partition shall be made from 6mm x 19 mm Flat bar fabricated as per reference images in powder coated finish as per the shade . 2) The Flat bar shall be fixed to the MS frame of 35 mm x 35 mm SHS CRS section powder coated connected to the flooring and ceiling with metal Anchor faster as per the reference images. 3) Hardware: - All consumable hardware as per by Architect/EIC from make list Onsite measurement shall be taken before manufacturing it. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site.

N5 O.T.S L.H.S Jali Parttion:SIZE 1730 X 2760 MM Providing, making, fixing & fabricating MS Jali partition in position as per reference drawings. 1) The partition shall be made from 6mm x 19 mm Flat bar fabricated as per reference images in powder coated finish as per the shade . 2) The Flat bar shall be fixed to the MS frame of 35 mm x 35 mm SHS CRS section powder coated connected to the flooring and ceiling with metal Anchor faster as per the reference images. 3) Hardware: - All consumable hardware as per by Architect/EIC from make list Onsite measurement shall be taken before manufacturing it. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site.

TV2 Director,MD cabin Modular TV Unit :Size : 900 X 300 X 230 MM Providing, making and fixing partly TV units in position PU finish as per reference drawings. 1) The box work shall be made from 19 mm thick BWP IS 710 Grade ply /engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm + Exterior grade MDF finish + colour PU polish as per the sample . 2) The unit shall fixed to the wall. 3) All internal shall be laminate finish as per the sample . 4) All external surface shall be PU finish as per the sample . 5) The unit shall have Aluminum profile shutter + multifunctional mechanism Free flap Smoked Glass shutter as per reference drawings. 6) Polishing: PU polish on all surfaces. 7) Provision for the electrical wire and switch shall be there,no wire shall be visible including the HDMI cable . 8) Hardware: - Multifunctional mechanism Free flap for shutter Onsite measurement shall be taken before manufacturing it. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site.

TV3 MD UHBVN, Chairman Modular TV Unit :Size : 2100 X 370 X 250 MM Providing, making and fixing partly TV units in position with multiple drawer PU finish as per reference drawings. 1) The box work & drawer shall be made from 19 mm thick BWP IS 710 Grade ply /engineering wood / PLB /MDF material and thickness of 25mm and legs 18mm + Exterior grade MDF finish + colour PU polish as per the sample . 2) The unit shall fixed to the wall. 3) All internal shall be laminate finish as per the sample . 4) All external surface shall be PU finish as per the sample . 5) The unit shall have one Aluminum profile shutter + multifunctional mechanism Free flap Smoked Glass shutter as per reference drawings. 6) Polishing: PU polish on all surfaces. 7) Provision for the electrical wire and switch shall be there,no wire shall be visible including the HDMI cable . 8) Hardware: - Multifunctional mechanism Free flap for shutter - Soft close Premium Channel for drawers: Quadro or equivalent as by Architect/EIC from make list (hettich) Onsite measurement shall be taken before manufacturing it. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site.

Built in Seating unit Seating unit Providing, making and fixing built in seating units in position with upholstery as per reference drawings. 1) The box work & paneling on wall shall be made from 19 mm thick BWP IS 710 Grade ply /engineering wood / PLB /MDF material + Exterior grade MDF finish as per the sample . 2) The unit shall be fixed to the wall and creat alcove for the seating unit. 3) Alcove elevation and all side shall be fully upholstered & cushion back. 4) Lining/upholstery work: - The stitching work shall be as per the design and pattern. Ergonomic required Density Latex foam & polyurethane foam shall be used. Top layer shall be of polyester fibre 130 GSM to 150 GSM or as per required comfort level. The whole assembly to be covered “Madarpat” and on it tapestry of make and shade to be fixed. 5) The seat shall have removable covers. 6) Woven small textured upholstery as per the sample . 7) All joinery and detailing shall be as per the reference images or design pattern. Basic cost of fabric shall be ₹. 2500 per Rmt.. Onsite measurement shall be taken before manufacturing it. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site.: Size : 4175 X 2525 MM

:Size : 3750 X 2525 MM

B1 Dispensary Providing and arranging inposition Patient Bed as per following specification. 1) Overall approximate dimension: 1880 x 600 x 750 (LxBxH) mm with adjustable Backrest. 2) Detachable Cushioned mattress of 75 mm thickness with upholstery. 3) Frame work shall be fabricated in CRS polished MS hollow box section epoxy powder coated with adjustable ratchet locks. 4) Legs fitted with PU Stumps.

Kitchen Counter Cafeteria Providing, making, fixing and positioning cafeteria bar counter. Counter Size : (1500 X 520 X 900 mm) x 2 nos Material of Construction: 1) Table top shall be made up of 19 mm thick BWP - IS 710 Grade ply /engineering wood / PLB /MDF material + 1mm thick laminate of make and shade with 45 mm thick teak wood beading on all the visible sides of edges. 2) Supporting framing for table top & leg shall be fabricated in 50 x 25 x 2.6 mm CRS polished MS hollow box section powder coated frame as per make, shade and quality. 3) Polishing: Exterior grade water based PU polish on all surfaces wood. 4) Heavy Duty Self Adjusting Levelers shall be fixed at the bottom of metal legs The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site.

AS3.1L Size : 1200 X 400 X 600

AS3.1R Size : 1200 X 400 X 600

AS4 Size : 1500 X 400 X 600

AS5.1L Size : 1600 X 400 X 600

AS6 Size : 1800 X 400 X 600

AS7 Size : 2000 X 400 X 600

AS7.1L Size : 2000 X 400 X 600

AS8 Size : 2100 X 400 X 600

Storage Unit : Providing, making and fixing storage units with multiple Drawers in position as per reference drawings. 1) The Box work,shutter,Drawer and shelves shall be made from BWP IS 710 Grade ply /engineering wood / PLB /MDF material. 2) The Shutter & Drawer shall be made of BWP IS 710 Grade ply /engineering wood / PLB /MDF material + laminate finish and 6mm teak wood beading all around. 3) Backing of storage shall be made from BWP IS 710 Grade ply /engineering wood / PLB /MDF material. + both side laminate finish as per the sample . 4) Laminate of 1.0 mm thickness shall be fixed of make and shade on All external & internal surface including both side of shelves & back side of unit. 5) Teak wood - 6 mm thick lipping on all ply edges.19mm x 75 mm thick solid wood base as per reference drawings. 6) Polishing: water base PU polish on all wooden surfaces. 7) Hardware: - Hinges: Auto close Hinges for open able shutters of make for open able shutters - Minumum 3 hinges per shutter. - Hinges: Auto close Hinges for open able shutters of make for open able shutters - Minumum 3 hinges per shutter. - Soft close premium Channel for drawers: Quadro or equivalent as by Architect/EIC from make list (hettich) - One multipurpose lock per active shutter and drawer of make - Tower bolt: Brass satin finish nickel plated or SS 304 150 mm long for upper shutters. - Handle/Knob: of SS 304 grades or Aluminum finish profile handle. - Adjustable shelves. Onsite measurement for storages, etc. shall be taken before manufacturing it. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. AS9.1L Back side Storage Size : 2400 X 400 X 600

AS9.1R Back side Storage Size : 2400 X 400 X 600

Back side Storage Size : 1600 X 400 X 600

Back side Storage Size : 2000 X 400 X 600

Storage Unit : Providing, making and fixing storage units with multiple Drawers in position as per reference drawings. 1) The Box work,shutter,Drawer and shelves shall be made from BWP IS 710 Grade ply /engineering wood / PLB /MDF material. 2) The Shutter & Drawer shall be made of exterior grade MDF + PU lamination polish of shade. 3) Unit top and all side shall be veneer finish as per the reference images. 4) Backing of storage shall be made from BWP IS 710 Grade ply /engineering wood / PLB /MDF material as per the sample . 5) Laminate of 1.0 mm thickness shall be fixed of make and shade on All internal surface including both side of shelves & internal side of unit. 6) Teak wood - 6 mm thick lipping on all ply edges as per reference drawings. 7) Polishing: PU polish on all wooden surfaces. 8) Hardware: - Hinges: Auto close Hinges for open able shutters of make for open able shutters - Minumum 3 hinges per shutter. - Hinges: Auto close Hinges for open able shutters of make for open able shutters - Minumum 3 hinges per shutter. - Soft close premium Channel for drawers: Quadro or equivalent as by Architect/EIC from make list (hettich) - One multipurpose lock per active shutter and drawer of make - Handle/Knob: of SS 304 grades or Aluminum finish profile handle. - Adjustable shelves. Onsite measurement for storages, etc. shall be taken before manufacturing it. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. AS10L Back side Storage Size : 2400 X 400 X 600

AS10R Back side Storage Size : 2400 X 400 X 600

Storage Unit : Providing, making and fixing storage units with multiple Drawers in position as per reference drawings. 1) The Box work,shutter,Drawer and shelves shall be made from BWP IS 710 Grade ply /engineering wood / PLB /MDF material. 2) The Shutter & Drawer shall be made of exterior grade MDF + PU lamination polish of shade. 3) Unit top and all side shall be veneer finish as per the reference images. 4) Backing of storage shall be made from BWP IS 710 Grade ply /engineering wood / PLB /MDF material as per the sample . 5) Laminate of 1.0 mm thickness shall be fixed of make and shade on All internal surface including both side of shelves & internal side of unit. 6) Teak wood - 6 mm thick lipping on all ply edges.19mm x 75 mm thick solid wood base as per reference drawings. 7) Polishing: PU polish on all wooden surfaces. 8) Hardware: - Hinges: Auto close Hinges for open able shutters of make for open able shutters - Minumum 3 hinges per shutter. - Hinges: Auto close Hinges for open able shutters of make for open able shutters - Minumum 3 hinges per shutter. - Soft close premium Channel for drawers: Quadro or equivalent as by Architect/EIC from make list (hettich) - One multipurpose lock per active shutter and drawer of make - Handle/Knob: of SS 304 grades or Aluminum finish profile handle. - Adjustable shelves. Onsite measurement for storages, etc. shall be taken before manufacturing it. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. AS11L Back side Storage Size : (1400 X 2) X 400 X 750

AS11R Back side Storage Size : (1400 X 2) X 400 X 750

AS12 Storage Storage Unit :Size 2100 X 400 X 600 MM Providing, making and fixing storage units with multiple shutter in position as per reference drawings. 1) The Box work,shutter and shelves shall be made from BWP IS 710 Grade ply /engineering wood / PLB /MDF material. 2) The Shutter shall be made of exterior grade MDF + PU lamination polish of shade. 3) Unit top and all side shall be veneer finish as per the reference images. 4) Backing of storage shall be made from BWP IS 710 Grade ply /engineering wood / PLB /MDF material as per the sample . 5) Laminate of 1.0 mm thickness shall be fixed of make and shade on All internal surface including both side of shelves & internal side of unit. 6) Teak wood - 6 mm thick lipping on all ply edges.19mm x 75 mm thick solid wood base as per reference drawings. 7) Polishing: PU polish on all wooden surfaces. 8) Hardware: - Hinges: Auto close Hinges for open able shutters of make for open able shutters - Minumum 3 hinges per shutter. - Hinges: Auto close Hinges for open able shutters of make for open able shutters - Minumum 3 hinges per shutter. - One multipurpose lock per active shutter and drawer of make - Handle/Knob: of SS 304 grades or Aluminum finish profile handle. - Adjustable shelves. Onsite measurement for storages, etc. shall be taken before manufacturing it. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site.

Storage Unit : Providing, making and fixing storage units in position as per reference drawings. 1) The Box work,shutter and shelves shall be made from BWP IS 710 Grade ply /engineering wood / PLB /MDF material + laminate finish and 6mm teak wood beading all around. 2) Backing of storage shall be made from BWP IS 710 Grade ply /engineering wood / PLB /MDF material + both side laminate finish as per the sample . 3) Laminate of 1.0 mm thickness shall be fixed of make and shade on All external & internal surface including both side of shelves & back side of unit. 4) Teak wood - 6 mm thick lipping on all ply edges.19mm x 75 mm thick solid wood base as per reference drawings. 5) Polishing: water base PU polish on all wooden surfaces. 6) Hardware: - Hinges: Auto close Hinges for open able shutters of make for open able shutters - Minumum 3 hinges per shutter. - One multipurpose lock per active shutter and drawer of make - Tower bolt: Brass satin finish nickel plated or SS 304 150 mm long for upper shutters. - Handle: Aluminum finish Gola/conceal profile handle as per the sample . - Magnet Catcher- of make 2 nos per active shutter - Adjustable shelves. Onsite measurement for storages, etc. shall be taken before manufacturing it. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. BS3 Storage Size : 1200 X 400 X 900

BS4 Storage Size : 1500 X 400 X 900

BS5Storage Size : 1600 X 400 X 900

BS6Storage Size : 1800 X 400 X 900

BS7 Storage Size : 2000 X 400 X 900

BS8 Storage Size : 2100 X 400 X 900

Storage Unit : Providing, making and fixing storage units in position as per reference drawings. 1) The Box work,shutter and shelves shall be made from BWP IS 710 Grade ply /engineering wood / PLB /MDF material + laminate finish and 6mm teak wood beading all around. 2) Backing of storage shall be made from BWP IS 710 Grade ply /engineering wood / PLB /MDF material + both side laminate finish as per the sample . 3) Laminate of 1.0 mm thickness shall be fixed of make and shade on All external & internal surface including both side of shelves & back side of unit. 4) Teak wood - 6 mm thick lipping on all ply edges.19mm x 75 mm thick solid wood base as per reference drawings. 5) Polishing: water base PU polish on all wooden surfaces. 6) Hardware: - Hinges: Auto close Hinges for open able shutters of make for open able shutters - Minumum 3 hinges per shutter. - One multipurpose lock per active shutter and drawer of make - Tower bolt: Brass satin finish nickel plated or SS 304 150 mm long for upper shutters. - Handle: Aluminum finish Gola/conceal profile handle as per the sample . - Magnet Catcher- of make 2 nos per active shutter - Adjustable shelves. Onsite measurement for storages, etc. shall be taken before manufacturing it. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. CS1 Storage Size : 600 X 400 X 1200

CS2 Storage Size : 900 X 400 X 1200

CS3 Storage Size : 1200 X 400 X 1200

CS3.1L Storage Size : 1200 X 400 X 1200

CS4 Storage Size : 1500 X 400 X 1200

CS5 Storage Size : 1600 X 400 X 1200

CS5.1L Storage Size : 1600 X 400 X 1200

CS5.1R Storage Size : 1600 X 400 X 1200

CS6 Storage Size : 1800 X 400 X 1200

CS7.1L Storage Size : 2000 X 400 X 1200

CS7.1R Storage Size : 2000 X 400 X 1200

CS8 Storage Size : 2100 X 400 X 1200

Storage Size : 1500 X 400 X 1200

Storage Size : 1300 X 400 X 1200

Storage Size : 1550 X 400 X 1200

Storage Size : 1950 X 400 X 1200

Storage Size : 2200 X 400 X 1200

Storage Size : 1800 X 400 X 1200

Storage Size : 1040 X 400 X 1200

Storage Unit : Providing, making and fixing storage units in position as per reference drawings. 1) The Box work,shutter and shelves shall be made from BWP IS 710 Grade ply /engineering wood / PLB /MDF material + laminate finish and 6mm teak wood beading all around. 2) Backing of storage shall be made from BWP IS 710 Grade ply /engineering wood / PLB /MDF material + both side laminate finish as per the sample . 3) Laminate of 1.0 mm thickness shall be fixed of make and shade on All external & internal surface including both side of shelves & back side of unit. 4) Teak wood - 6 mm thick lipping on all ply edges.19mm x 75 mm thick solid wood base as per reference drawings. 5) Polishing: water base PU polish on all wooden surfaces. 6) Hardware: - Hinges: Auto close Hinges for open able shutters of make for open able shutters - Minumum 5 hinges per shutter. - One multipurpose lock per active shutter and drawer of make - Tower bolt: Brass satin finish nickel plated or SS 304 150 mm long for upper shutters. - Handle: Aluminum finish Gola/conceal profile handle as per the sample . - Press magnet catches(Cabinet Push Open Catch Touch Latch Magnetic) - of make 2 nos per active shutter - Adjustable shelves. Onsite measurement for storages, etc. shall be taken before manufacturing it. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. DS3 Storage Size : 1200 X 400 X 2100

DS4 Storage Size : 1500 X 400 X 2100

DS6 Storage Size : 1800 X 400 X 2100

DS8 Storage Size : 2100 X 400 X 2100

Storage Size : 3190 X 400 X 2100

Storage Size : 2800 X 400 X 2100

Storage Unit : Providing, making and fixing storage units in position as per reference drawings. 1) The Box work,shutter and shelves shall be made from BWP IS 710 Grade ply /engineering wood / PLB /MDF material + laminate finish and 6mm teak wood beading all around. 2) Backing of storage shall be made from BWP IS 710 Grade ply /engineering wood / PLB /MDF material + both side laminate finish as per the sample . 3) Laminate of 1.0 mm thickness shall be fixed of make and shade on All external & internal surface including both side of shelves & back side of unit. 4) Teak wood - 6 mm thick lipping on all ply edges.19mm x 75 mm thick solid wood base as per reference drawings. 5) Polishing: water base PU polish on all wooden surfaces. 6) Hardware: - Hinges: Auto close Hinges for open able shutters of make for open able shutters - Minumum 3 hinges per shutter. - One multipurpose lock per active shutter and drawer of make - Tower bolt: Brass satin finish nickel plated or SS 304, 150 mm long for upper shutters. - Handle: Aluminum finish Gola/conceal profile handle as per the sample . - Magnet Catcher- of make 2 nos per active shutter - Adjustable shelves. Onsite measurement for storages, etc. shall be taken before manufacturing it. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. ES3 Storage Size 1200 X 400 X 2100

ES3.1L Storage Size 1200 X 400 X 2100

ES4 Storage Size 1500 X 400 X 2100

ES6 Storage Size 1800 X 400 X 2100

Storage Size 1400 X 400 X 2100

Providing, making and fixing storage units with multiple shutter in position as per reference drawings. 1) The Box work,shutter and shelves shall be made from BWP IS 710 Grade ply /engineering wood / PLB /MDF material. 2) The Shutter shall be made of exterior grade MDF + PU lamination polish of shade. 3) Unit top and all side shall be veneer finish as per the reference images. 4) Backing of storage shall be made from BWP IS 710 Grade ply /engineering wood / PLB /MDF material as per the sample . 5) Laminate of 1.0 mm thickness shall be fixed of make and shade on All internal surface including both side of shelves & internal side of unit. 6) Teak wood - 6 mm thick lipping on all ply edges.19mm x 75 mm thick solid wood base as per reference drawings. 7) Polishing: PU polish on all wooden surfaces. 8) Hardware: - Hinges: Auto close Hinges for open able shutters of make for open able shutters - Minumum 3 hinges per shutter. - Hinges: Auto close Hinges for open able shutters of make for open able shutters - Minumum 3 hinges per shutter. - One multipurpose lock per active shutter and drawer of make - Handle/Knob: of SS 304 grades or Aluminum finish profile handle. - Adjustable shelves. Onsite measurement for storages, etc. shall be taken before manufacturing it. The work shall be done as per the shop drawing (to be prepared by contractor), specifications, sample and as directed by the Architect and Engineer-in-charge. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles,adhesives, consumable hardwares & required SS 304 grade hardware/accessories of make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill Architect's design intent. No additional claims will be entertained for this. The unit shall be manufactured in parts and these parts shall be assembled at site. ES9 Storage Size 1400 X 370 X 2100