COMPREHENSIVE REPAIRS / REPLACEMENT TO B/R NATURE WORK OF OTM ACCN (ZONE B) IN THE AOR OF AGE B/R-I UNDER GE HISAR AT HISAR MIL STN.

Amount

Taking down chowkat or frame with shutters area not exc. 1.5 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts noth / disturbed portion with pcc 1:3:6 complete all as specified

Taking down shutters of any description exc 1 Sqm and not exc. 2 Sqm each all as directed.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises.

Hacking out old broken glass any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins/spring clips complete all as specified and as directed.

Raking out joints/pointing to brick work or brick tiles, laid flat, in floors, surface channels, roofs, etc all as specified.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level.) & removing unserviceable materials in low laying area, complete, all as directed.

Demolition of brick/stone masonry built in cement/lime mortar of any mix and stacking serviceable stones aside for reuse & removing unserviceable materials in low laying area, complete, all as directed.

Dismantling of brick tiles or terracing tiles single layer on roofs complete all as specified.

Dismantling of cast iron pipes of any size of bore as in soil, waste or vent pipe including removal of cement joint fixed to wall or laid in floor complete all as specified and directed .

M & L for rendering 10mm thick in cement mortar 1:3 on faces of concrete surfaces in ceiling, finished even and smooth without using extra cement complete all as specified and directed

Material and labour preparation of newly plastered/asbestos cement surfaces of ceilings & applying three coats of white wash complete all as specified.

M & L for rendering 15mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified.

M&L for preparation of new plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer on walls all as specified & as directed..

M & L for rendering 15mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces of walls, finished even and fair complete all as specified.

M&L for rough cast finish plaster by applying the under coat of cement and sand mortar 1:3 not less than 10 mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even complete .

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint on walls over a coat of primer all as specified & as directed.

M&L for preparing the old decorated plastered /un plastered surfaces of walls including cornices by brooming down or steel wire brushing scrapping down or steel wire brushing scrapping down smoke soot etc. and applying one coat of cement base paint of approved shade/tint on wall surface to give uniform and smooth surface etc complete all as specified and as directed

M&L for preparation of old surfaces (plastered or unplastered) of walls including cornices, pilasters etc including brooming or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and applying one coat of oil emulsion distemper (OBD) of approved shade/tint all as specified & as directed.

M&L for complete removal (any number of layers) of existing treatment includign cleaning of mortar drops, smoke soot, moulds, moss efforescent salts, treating oil, greasy spots etc by steel brushed or by any other suitable scrapping tools including cleaning of surfaces by spraying water and thereafter preparing of scrapped surfaces with 1mm thick wall care putty and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of 1mm thick wall care putty and a coat of primer of same make all as specified & as directed. Note (a) The area of entire one bldg will be scrapped/removed and will be prepared with wall care putty. (b) OBD work will not be allowed until unless putty work is completed for whole bldg. (c) 2nd coat of OBD will be allowed only after 1st coat is completed for bldg.

M&L for preparing the old decorated plastered /un plastered surfaces of ceilings including cornices by brooming down or steel wire brushing scrapping down or steel wire brushing scrapping down smoke soot etc and applying one coat of white wash to give uniform and smooth surface etc complete all as specified and directed.

M&L for preparing the old decorated plastered /un plastered surfaces of walls including cornices by brooming down or steel wire brushing scrapping down or steel wire brushing scrapping down smoke soot etc. and applying one coat of cement base paint of approved shade/tint on wall surface to give uniform and smooth surface etc complete all as specified and as directed.

M&L for complete removal (any number of layers) of existing treatment by using scaffolding,ladder, cradles & other protective measures which are necessary for execution of work up to 15mtr height including cleaning of mortar drops, smoke soot, moulds, moss, efforscent salts, treating oil, greasy spots etc by steel brushed or by any othr suitable scrapping tools including cleaning of surfaces by spraying water and thereafter preparing of scrapped surfaces with 1mm thick wall care putty and applying two coats of cement base paint (OBP) over a coat of primer of approved shade/tint on wall surface to give uniform and smooth surface etc complete all as specifeid and as directed. Note. (a) The area of entire one bldg will be scraped/ removed and will be prepared with wall care putty. (b) CBP work will not be allowed until unless putty work is completed for whole bldg. (c) 2nd coat of CBP will be allowed only after 1st coat is completed for entire bldg.

M&L for preparation of old painted surfaces of wood and wood based material any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint all as specified & as directed.

M&L for preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint all as specified & as directed.

M&L for brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified.

M&L brick work with subclass 'B' old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified.

M&L for vitrified ceramic tiles 1st quality, 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

M&L for vitrified ceramic tiles 1st quality, 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for glazed ceramic designer & pattern (dark & light shade) tiles (coloured), premium quality, 450mm x 300mm x 7mm thick, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for non skid ceramic jointless tiles (coloured) 1st quality, 7 to 8mm thick, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for 20mm thick Granite slab of approved shade (any colour), as in cooking platform, shelves etc, bedded & jointed with grey cement slurry and pointed with white cement with admixure of pigment to match with shade of Granite stone including necessary cuttings to fit in the shapes of shelves, grinding and polishing including required cutting to suit the size of platforms, making outer edges round including 15mm thick screed bed in cement & sand ortar 1:4 complete all as specifeid and as directed.

All as per srl item No 32.00 above, but for fixing of WHBs, urinal partitions corner shelves of any shape and size including necessary cutting to required shape and sizes and rounding the external edges of stone, complete all as specieid and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified & directed.

Supply and fixing factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified & directed.

Supply and fixing factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified and directed

Supply & fixing stainless steel butt hinges of size 100mm medium weight, cold rolled fixed with stainless steel screw ISI marked complete all as specified.

Supply & fixing butt hinges of size 100mm medium weight, cold rolled fixed with mild steel screw ISI marked complete all as specified.

S&F 150mm long extruded aluminium alloy handles, fabricated type, anodised (ISI marked) complete all as specified.

S&F 150mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified.

S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified.

Supply and fix 15mm bore fancy type pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes & fly nuts, screwed for iron pipes all as specified and directed.

S&F in repairs Bib taps,cast copper alloy with crutch or butterfly handle, chromium plated, fancy type , screwed for iron pipe or for brass ferrule, for 15 mm bore GI pipe complete all as specified and directed.

S&F in repairs 15mm bore angle valve, chromium plated, fancy type, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions all as specified and directed.

S&F in repairs 15mm bore Stop valve fancy type with long shank and cup (concealed type) of cast copper alloy chromium plated screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union and fixed complete all as specified and directed

S&F in repairs, PVC connection 450 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F in repairs stainless steel Grating doom 125 mm dia with waste hole all as directed.

S&F in repair brass chromium plated overhead shower rose 125mm dia round shape with swivel joints complete all as specified and directed.

S&F in repairs Jet Spray with 1 Meter PVC Tube (Stainless Steel) complete all as specified and as directed.

S&F in repairs vitreous china half stall urinal, any type, white with grating and union for discharge pipe includng providing and fixing plugs, bedding urinal against wall in CM (1:2), securing urinal to plugs with and including 60mm long brass screws complete with PVC flush pipe complete all as specified and as directed.

S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore PTMT waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified.

S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, with PTMT 'P' or 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe etc including provision of PCC (1:5:10) type E2 in filling, making good to floor, complete all as specified.

S&F in repairs vitreous china wash down water closet (Padestal pattern) White, with 'P' or 'S' trap including plastic water closet seat cover, black, closed pattern with flat bottom with mild steel chromium plated or aluminium hinging device and fixing with all joints including connection to drain or outgoing pipe and to flushing pipe, anti-syphonage pipe etc complete all as specified and as directed.

S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.

S&F in repairs Plastic water closet seat cover, fancy type, white colour closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device.

S&F 3mm thick polycarbonate solid sheet, in square/rectangular size, smooth surface, weather resistant, fine finish, bent and pressed including aluminium glazing clips, rubber beading and clear silicon or glazing with oil putty with putty or fixed with beads complete all as specified and directed.

S&F stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple complete all as specified.

Supply and fixing as in repairs stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple complete all as specified.

Taking up or down 15mm bore steel tubing and connection incl cleaning for refixing or removal to store

Taking up or down 20mm bore steel tubing and connection incl cleaning for refixing or removal to store

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed.

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

Supply and fixing in repair 1000 Litre capacity Rotational moulded polyethylene water storage tanks (colour other than black as approved by Engineer-in-charge) triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

Supply and fixing in repair 500 Litre capacity Rotational moulded polyethylene water storage tanks (colour other than black as approved by Engineer-in-charge) triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20mm bore (minimum weight 210 gms) complete all as specified and as directed.

S&F Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 15mm bore (minimum weight 142 gms) complete all as specified and as directed.

S&F in repairs Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 15mm bore.

S&F in repairs Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 20mm bore.

S&F in repairs Door closer aluminium (extruded section body), hydraulically regulated, designation No. 2 universal type, suitable for door shutters of 851mm to 1000mm in width and of weight between 61 to 80 kg and fixed complete all as specified & as directed.

M&L for PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in levelling course 25mm thick finished fair & even complete all as specified & as directed.

M&L for bricks tiles, of old size sub class ‘A’, laid flat, in roofs, bedded in CM 1:6 & pointed in CM 1:3 complete all as specified & as directed.

M&L for machine cut Kota stone slab flooring 18 to 20mm thick laid over & including screed bed or bedding layer of 15mm thick in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified. Note : - Kota stone shall be of size 550mm x 550mm (minimum) when brought at site.

M&L for machine cut Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar, laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing laid over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for grinding, rubbing and mirror finish polishing to existing kota stone/mosaic floors/vertical surafces etc complete by mechanically by using different grits all as specified and directed.

M&L for factory made vibrate type chequered cement concrete coloured tiles, glossy finish, 25cm x 25cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement & pigment, laid over & including 20mm thick screed bed in cement & sand mortar 1:4, complete, all as specified & as directed.

M&L for 75mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L flush pointing to brick walls in cement mortar 1:3 all as specified.

S&F mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified.

S&F in repairs 100mm bore pipe cast iron sand pipes for soil and waste and vent pipes in any length with our without cars , with cement joints laid in trenches or in floors or fixed to wall complete all as specified.

S&F in repairs 75mm bore pipe cast iron sand pipes for soil and waste and vent pipes in any length with our without cars , with cement joints laid in trenches or in floors or fixed to wall complete all as specified.

S&F 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified & as directed.

S&F 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified & as directed.

S&F 100mm bore cast iron branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door

S&F 75mm bore cast iron branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door

S&F 100mm bore cast iron 'P' or 'S' trap complete all as specified & as directed.

S&F 75mm bore cast iron 'P' or 'S' trap complete all as specified & as directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints fixed to walls with necessary MS / PVC clamps and necessary screwing complete all as specified.

S&F 110mm bore PVC (SWR) bend with access door all as specified & as directed.

S&F in repairs Peg set of 06, steel chromium plated complete all as specified and as directed.

M/s Devendera construction (BID ID -3114263)

M/S D.N Choudhary (BID ID -3116159)

Balaji Construction Co. (BID ID -3126953)

VIKAS INFRASTRUCTURE (BID ID -3116062)

moti construction company (BID ID -3124805)

SHRI HARI BUILDERS (BID ID -3127292)

malik constructions (BID ID -3106157)

M/s Rao Constructions, 1173 Urban Estate-II, Hisar (BID ID -3127336)