Pre-Bid EOI Document for Selection of Channel Partner/Supplier/Authorized Distributor for Provision of Telecom assets with IP MPLS based technology

Description:- Design, Fabricate, Supply, of Label Edge Router (LER) as per RDSO Technical Advisory Note (TAN) No. STT/TAN/IP-MPLS/2020 Ver 3.0, Amd-1 or latest with non-blocking throughput of 160 Gbps full duplex or higher. The router should have console and SNMP interface, FAN Modules, Dust Filters, Dual main control card modules in redundant design supporting 1:1 hot stand by mode. Redundant 48V DC power supply modules etc., including connecting cables and fixing accessories from day one. The IP-MPLS router should support minimum 8x10G, 32x1G, 2xSTM1 and 2x16E1 CES interface (G.703) modules.The Router should be equipped with following interface cards and modules. (i) 4 x 10G (Optical) interface equally distributed in two cards, each minimum 2X10G SFP+ interface card, along with 4 no.of 10 G (40KM) SFP+ modules fully loaded suitable for single fiber as per site requirement. (ii) 8 x 1GbE optical interface equally distributed in two cards, each minimum 4X1GbE interface card, along with 8 no.of 1 GbE (10KM) SFP modules fully loaded. (iii) 4 X 1GbE copper interface card to connect various networks of station (iv) 16 x E1(G.703) interface equally distributed in two cards each minimum 8x E1(G.703) interface card. (Inspection by RDSO). This also include "Installation of switches, with power distribution panel and all accessories in the Rack (19") , DDF, Aluminum runway ladder, necessary ofc patch cord etc and their testing and commissioning. This also includes termination of all E1's on DDF, connection of pigtails, optical patch cords, CAT6 Cable and 48 V bus to the IPMPLS equipment including supply of wires and connectors. It also includes proper mounting of rack, provision of Aluminum runway ladder, casing and capping and conduit pipe as per requirement at each station and other necessary materials supplied by Railways from Stores for installation. (Conduit pipe/casing and capping with ISI standards, aluminum runway ladder, Optical patch cords and UTP patch cords and all other miscellaneous materials should be supplied by the contractor).

Description:- "Supply of 4 port x 10G SFP+ interface module card suitable for the IP MPLS router (The card should be compatible and suitable with existing system available in section) ( Inspection by RDSO )"

Description:- "Supply of 8 port x 1GbE (4 nos of optical ports and 4 nos of electrical ports) interface module card suitable for the IP-MPLS router (The card should be compatible and suitable with existing system available in section)( Inspection by RDSO )"

Description:- "Supply of 16 port channelized E1 interface card suitable for the IP-MPLS router (The card should be compatible and suitable with existing system available in section) ( Inspection by RDSO )"

Description:- Supply of SFPs for 1Gbe (optical)/RJ 45 ports as per the site requirement (Inspection by RITES)

Description:- Supply of SFP + 10G (40 km) SMF, 1550 nm for 40 km transmission working on single fibre (Inspection by RITES)

Description:- Supply of DDF (120 Ohms) for terminating 16 E1s of wrapping type and mountable on 19"" rack, similar to puncom or reputed make. (Maximum width 2U size) (Inspection by Consignee)

Description:- Supply of fully covered 19'' Racks of size 2200 mm X 600 mm 600mm complete with all fittings including DC Fans (48 V) -2Nos, with air filters at the sides. Separate or sheet/plate to keep testing equipment's - 1 No and AC Power distribution panel(horizontal fitting) with power sockets and fuse/MCB protection (minimum 6 Nos of 230V-15A/5A. combined) and Earth Strip and other accessories. Rack should have compatibility with all equipment conforming to DIN41494 or equivalent EIA/ISO/EN standard, Manufacture must certify that products are complied with DIN41494 or equivalent EIA/ISO/EN/CEA/UL standards(Inspection by RITES)

Description:- Supply of VRLA fully charged battery 48 V DC /300 AH (stackable) as per IRS:S-93/96(A)(amd-1) or latest.(Inspection by RDSO)

Description:- Supply of 25A, 48 V (2+1) FR/FC module RDSO /SPN/TC/23/1999 or latest with AC input range 90-300 Volts, (Inspection by RDSO)

Description:- Supply of DC Power distribution panel to cater DC power requirements of IPMPLS/STM Multiplexers /PD Muxes / EOW /FANS to be fixed in 19"" rack with inbuilt line filter & Surge protection on 48V DC to be catered the demand of the load. The materials should be ISI certified or reputed make. (Minimum 8 Nos of DC distribution arrangement with MCB's of suitable rating for -ve. Connecting copper strip for +ve) (Inspection by Consignee)

Description:- Supply of Tool Kit consisting of Optical power meter, Digital Multimeter, Ethernet Crimping Tool, LAN tester, Krone tool, Rapping Tool, Universal Spanner Set, Screw Driver Set (7 Pieces set), Cutting plier, Wire Stripper. as per Spec in the Tender document with OEM test report and warranty certificate (inspection by CONSIGNEE ) All the materials should be ISI certified or reputed make

Description:- Supply of optical time Domain Reflectometer with VFI (OTDR) as per Spec in the Tender document with OEM test report and warranty certificate of reputed make like EXFO 735D or latest of better make (inspection by RITES )

Description:- Supply of optical patch cords with FCPC/SCPC to SCPC/LCPC connecters (10 mtrs long), so as to suit OFC terminations and the IPMPLS equipment supplied. (Inspection by CONSIGNEE). All materails should be ISI certified or reputed make

Description:- Supply of 10G SFP+ Module with 80 Km range for above Routers as per technical specification (Inspection by RITES)