LED Luminaire (for Flood Light)

LED Luminaire (for Flood Light)

LED LED Luminaire (for Flood Light) ( 2 ) Technical Specifications Specification Specification Name Values Allowed Values STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 5/2012 latest and IS: 16107 (Part 2/Sec 1):2012 latest Yes - Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes - Types of LED Luminaire as per the IS: 16107(Part-2 Sec.-1)/2012 Type B - Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 - LED Rating/System Wattage/Rated Power 125W 15W

20W

25W

30W

40 W

50W

55W

60W

70W

75W

80W

90W

100W

1 20W

125W

150W

200W

250W

300W

350W

400 W

500W Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt - 1/64 Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest IP65 - Mounting brackets (included) Adjustable - Warranty for free replacement (in Years) 2 - ELECTRICAL EFFICIENCY Input operating Voltage range and frequency 90 to 300 V olts AC at 50 Hz+/-2 Hz - Automatic Higher Cut off voltage above 300 volt Yes - Rated voltage 230 V AC 50 Hz - AC Power Factor at full load ≥ 0.95 - Driver Efficiency (in %age) ≥85 - Total Harmonics Distortion (in %age) ≤ 10 - "The total circuit power shall not be more than 110 percent of the value declared by the manufacturer" Yes - OPTICAL LED chip Efficacy ≥130 Lm/Watt - Colour temperature (+/-500K) 6000K - Working life for LED (Minimum 50

000 burning hours as per LM-80 report) Yes - Colour Rendering Index(CRI) ≥70 - Beam Angle ≥120 - Optic lense materal (UV stabilised) (Write NA for without optic lense supply) NA - THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes - Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes - 2/64 Junction temperature < 85 degC - Operating temperature range -10 deg C to +55 deg C - Operating Humidity Range 10 % to 95% RH - PROTECTION Short circuit Protection Yes - Over load protecton Yes - Over Voltage protection Yes - Reverse polarity Yes - High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes - Insulation resistance between earth and current carrying part >100 M ohm - The luminaire shall be protected against surges and transients ( Internal) >/=4KV - The luminaire shall be protected against surges and transients of >/=10KV (External) No - CONSTRUCTIONAL The Luminaires casing/housing (single piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity Yes - The luminaire body must be corrosion resistant epoxy powder coated Yes - All fastners must be of stainless steel Yes - The entire housing (both LED section and driver section) shall be dust and water proof having IP 66 protection as per IS:10322 (Part 1):1982 latest Yes - Extruded silicon loop gasket shall be provided in the lantern body to ensure a Yes - 3/64 weather proof seal between the UV Glass cover and the metal housing to exclude the entry of the dust

water

insects etc.

Luminaries light transparency should be of Toughened glass Yes - Toughned transparent glass cover thickness >/=4 mm - Toughned Glass shall not get discoloured shall not suffer degration due to heat and ageing within warranty period Yes - Number of electronic control gear (power supplies) 1 No. 1 No.

2 Nos.

3 Nos.

4 Nos. Driver components shall be industrial grade or above Yes - PCB shall be FR4 grade minimum 0.8 to 1.0 mm thick or more Yes - The Luminaires works on single phase three wires system (Phase

Neutral and Earth) Yes - Suitable connector shall be provided for LED connection between driver output and LED Yes - Length of ISI marked three core wire (shall be provided along with supply of material) 50 cm - Light Source SMD LED Chip as per LM 80/IS16106 - MARKING "Manufactures Name and and brand on the aluminium die cast body Engraved/Embossed - Manufacturer’s name

model number

serial number Yes - Date of manufacture (month-year)

and lot Yes - 4/64 number as identification mark inside each unit and the outside of each packaging box The operation characteristics voltage and power be marked inside of each LED luminaire unit Yes - REPORTS AND CERTIFICATIONS LED Make OSRAM/NICHIA/CREE SAMSUNG/SEOUL LUMILED/PHILIPS EDISON/SYSKA LUMENMAX EVERLIGHT BRIDGELUX NATIONSTAR/REFOND - System must have EMI/EMC compliance as applicable (Test reports shall be furnish on demand by buyer/consignee) Yes - LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government lab/NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-79 report shall have total lumen output

power

PF

Current in Amps

CRI & CCT etc.

) Yes - LM 80 & TM 21 (Part of LM 80) (Ref. IS:16105:2012) Reports and Photo biological report for LED report from Central Government lab NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-80 report shall haveand the Pohoto Biological report of the LED Chip being used in the luminaire) Yes - Availability of test Report from Central Yes - 5/64 Government lab/NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-5/2012 and IS 16107 (Part 2/Sec 1) : 2012 Seller has to furnish Type test report on demand by buyer/consignee Yes - DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes - LED Luminaire for Flood Light shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 5): 2012 as applicable on the date Yes - * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001

O/o Executive Engineer

(E&M) Public Works Department Sirpur Bhawan Parisar

Raipur. (C.G.) 2 15 LED Luminaire (for Flood Light) ( 12 ) Technical Specifications Specification Specification Name Values Allowed Values STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 5/2012 latest and IS: 16107 (Part 2/Sec 1):2012 latest Yes - Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes - Types of LED Luminaire Type B - 6/64 as per the IS: 16107(Part-2 Sec.-1)/2012 Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 - LED Rating/System Wattage/Rated Power 15W 15W

500W Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt - Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest IP65 - Mounting brackets (included) Adjustable - Warranty for free replacement (in Years) 2 - ELECTRICAL EFFICIENCY Input operating Voltage range and frequency 90 to 300 V olts AC at 50 Hz+/-2 Hz - Automatic Higher Cut off voltage above 300 volt Yes - Rated voltage 230 V AC 50 Hz - AC Power Factor at full load ≥ 0.95 - Driver Efficiency (in %age) ≥85 - Total Harmonics Distortion (in %age) ≤ 10 - "The total circuit power shall not be more than 110 percent of the value declared by the manufacturer" Yes - OPTICAL LED chip Efficacy ≥130 Lm/Watt - Colour temperature (+/-500K) 6000K - Working life for LED (Minimum 50

000 burning hours as per LM-80 report) Yes - Colour Rendering Index(CRI) ≥70 - Beam Angle ≥120 - 7/64 Optic lense materal (UV stabilised) (Write NA for without optic lense supply) NA - THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes - Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes - Junction temperature < 85 degC - Operating temperature range -10 deg C to +55 deg C - Operating Humidity Range 10 % to 95% RH - PROTECTION Short circuit Protection Yes - Over load protecton Yes - Over Voltage protection Yes - Reverse polarity Yes - High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes - Insulation resistance between earth and current carrying part >100 M ohm - The luminaire shall be protected against surges and transients ( Internal) >/=4KV - The luminaire shall be protected against surges and transients of >/=10KV (External) No - CONSTRUCTIONAL The Luminaires casing/housing (single piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity Yes - The luminaire body must be corrosion resistant epoxy powder coated Yes - 8/64 All fastners must be of stainless steel Yes - The entire housing (both LED section and driver section) shall be dust and water proof having IP 66 protection as per IS:10322 (Part 1):1982 latest Yes - Extruded silicon loop gasket shall be provided in the lantern body to ensure a weather proof seal between the UV Glass cover and the metal housing to exclude the entry of the dust

Yes - Luminaries light transparency should be of Toughened glass Yes - Toughned transparent glass cover thickness >/=4 mm - Toughned Glass shall not get discoloured shall not suffer degration due to heat and ageing within warranty period Yes - Number of electronic control gear (power supplies) 1 No. 1 No.

Neutral and Earth) Yes - Suitable connector shall be provided for LED connection between driver output and LED Yes - Length of ISI marked three core wire (shall be provided along with 50 cm - 9/64 supply of material) Light Source SMD LED Chip as per LM 80/IS16106 - MARKING "Manufactures Name and and brand on the aluminium die cast body Engraved/Embossed - Manufacturer’s name

and lot number as identification mark inside each unit and the outside of each packaging box Yes - The operation characteristics voltage and power be marked inside of each LED luminaire unit Yes - REPORTS AND CERTIFICATIONS LED Make OSRAM/NICHIA/CREE SAMSUNG/SEOUL LUMILED/PHILIPS EDISON/SYSKA LUMENMAX EVERLIGHT BRIDGELUX NATIONSTAR/REFOND - System must have EMI/EMC compliance as applicable (Test reports shall be furnish on demand by buyer/consignee) Yes - LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government lab/NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-79 report shall have total lumen output

) Yes - LM 80 & TM 21 (Part of LM 80) (Ref. IS:16105:2012) Reports and Photo biological Yes - 10/64 report for LED report from Central Government lab NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-80 report shall haveand the Pohoto Biological report of the LED Chip being used in the luminaire) Availability of test Report from Central Government lab/NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-5/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes - Seller has to furnish Type test report on demand by buyer/consignee Yes - DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes - LED Luminaire for Flood Light shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 5): 2012 as applicable on the date Yes - * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001

Raipur. (C.G.) 12 15 LED Luminaire (for Flood Light) ( 6 ) Technical Specifications 11/64 Specification Specification Name Values Allowed Values STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 5/2012 latest and IS: 16107 (Part 2/Sec 1):2012 latest Yes - Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes - Types of LED Luminaire as per the IS: 16107(Part-2 Sec.-1)/2012 Type B - Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 - LED Rating/System Wattage/Rated Power 120W 15W

500W Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt - Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest IP65 - Mounting brackets (included) Adjustable - Warranty for free replacement (in Years) 2 - ELECTRICAL EFFICIENCY Input operating Voltage range and frequency 90 to 300 V olts AC at 50 Hz+/-2 Hz - Automatic Higher Cut off voltage above 300 volt Yes - Rated voltage 230 V AC 50 Hz - AC Power Factor at full load ≥ 0.95 - Driver Efficiency (in %age) ≥85 - Total Harmonics Distortion (in %age) ≤ 10 - "The total circuit power shall not be more than 110 percent of the value declared by the Yes - 12/64 manufacturer" OPTICAL LED chip Efficacy ≥130 Lm/Watt - Colour temperature (+/-500K) 6000K - Working life for LED (Minimum 50

000 burning hours as per LM-80 report) Yes - Colour Rendering Index(CRI) ≥70 - Beam Angle ≥120 - Optic lense materal (UV stabilised) (Write NA for without optic lense supply) NA - THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes - Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes - Junction temperature < 85 degC - Operating temperature range -10 deg C to +55 deg C - Operating Humidity Range 10 % to 95% RH - PROTECTION Short circuit Protection Yes - Over load protecton Yes - Over Voltage protection Yes - Reverse polarity Yes - High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes - Insulation resistance between earth and current carrying part >100 M ohm - The luminaire shall be protected against surges and transients ( Internal) >/=4KV - The luminaire shall be protected against No - 13/64 surges and transients of >/=10KV (External) CONSTRUCTIONAL The Luminaires casing/housing (single piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity Yes - The luminaire body must be corrosion resistant epoxy powder coated Yes - All fastners must be of stainless steel Yes - The entire housing (both LED section and driver section) shall be dust and water proof having IP 66 protection as per IS:10322 (Part 1):1982 latest Yes - Extruded silicon loop gasket shall be provided in the lantern body to ensure a weather proof seal between the UV Glass cover and the metal housing to exclude the entry of the dust

4 Nos. Driver components shall be industrial grade or above Yes - PCB shall be FR4 grade minimum 0.8 to 1.0 mm thick or more Yes - 14/64 The Luminaires works on single phase three wires system (Phase

and lot number as identification mark inside each unit and the outside of each packaging box Yes - The operation characteristics voltage and power be marked inside of each LED luminaire unit Yes - REPORTS AND CERTIFICATIONS LED Make OSRAM/NICHIA/CREE SAMSUNG/SEOUL LUMILED/PHILIPS EDISON/SYSKA LUMENMAX EVERLIGHT BRIDGELUX NATIONSTAR/REFOND - System must have EMI/EMC compliance as applicable (Test reports shall be furnish on demand by buyer/consignee) Yes - LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government Yes - 15/64 lab/NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-79 report shall have total lumen output

) LM 80 & TM 21 (Part of LM 80) (Ref. IS:16105:2012) Reports and Photo biological report for LED report from Central Government lab NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-80 report shall haveand the Pohoto Biological report of the LED Chip being used in the luminaire) Yes - Availability of test Report from Central Government lab/NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-5/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes - Seller has to furnish Type test report on demand by buyer/consignee Yes - DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes - LED Luminaire for Flood Light shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 5): 2012 as applicable on the date Yes - * Bold specifications are the golden parameters. Consignees and Quantity 16/64 S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001

Raipur. (C.G.) 6 15 LED Luminaire (for Flood Light) ( 8 ) Technical Specifications Specification Specification Name Values Allowed Values STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 5/2012 latest and IS: 16107 (Part 2/Sec 1):2012 latest Yes - Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes - Types of LED Luminaire as per the IS: 16107(Part-2 Sec.-1)/2012 Type B - Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 - LED Rating/System Wattage/Rated Power 150W 15W

500W Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt - Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest IP65 - Mounting brackets (included) Adjustable - Warranty for free replacement (in Years) 2 - ELECTRICAL EFFICIENCY Input operating Voltage range and frequency 90 to 300 V olts AC at 50 Hz+/-2 Hz - Automatic Higher Cut off voltage above 300 volt Yes - 17/64 Rated voltage 230 V AC 50 Hz - AC Power Factor at full load ≥ 0.95 - Driver Efficiency (in %age) ≥85 - Total Harmonics Distortion (in %age) ≤ 10 - "The total circuit power shall not be more than 110 percent of the value declared by the manufacturer" Yes - OPTICAL LED chip Efficacy ≥130 Lm/Watt - Colour temperature (+/-500K) 6000K - Working life for LED (Minimum 50

000 burning hours as per LM-80 report) Yes - Colour Rendering Index(CRI) ≥70 - Beam Angle ≥120 - Optic lense materal (UV stabilised) (Write NA for without optic lense supply) NA - THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes - Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes - Junction temperature < 85 degC - Operating temperature range -10 deg C to +50 deg C - Operating Humidity Range 10 % to 95% RH - PROTECTION Short circuit Protection Yes - Over load protecton Yes - Over Voltage protection Yes - Reverse polarity Yes - High voltage test (1.5 KV for one minute Yes - 18/64 between supply terminals and body of the unit) Insulation resistance between earth and current carrying part >100 M ohm - The luminaire shall be protected against surges and transients ( Internal) >/=4KV - The luminaire shall be protected against surges and transients of >/=10KV (External) No - CONSTRUCTIONAL The Luminaires casing/housing (single piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity Yes - The luminaire body must be corrosion resistant epoxy powder coated Yes - All fastners must be of stainless steel Yes - The entire housing (both LED section and driver section) shall be dust and water proof having IP 66 protection as per IS:10322 (Part 1):1982 latest Yes - Extruded silicon loop gasket shall be provided in the lantern body to ensure a weather proof seal between the UV Glass cover and the metal housing to exclude the entry of the dust

Yes - Luminaries light transparency should be of Toughened glass Yes - Toughned transparent glass cover thickness >/=4 mm - Toughned Glass shall not get discoloured shall not suffer Yes - 19/64 degration due to heat and ageing within warranty period Number of electronic control gear (power supplies) 1 No. 1 No.

and lot number as identification mark inside each unit and the outside of each packaging box Yes - The operation characteristics voltage and power be marked inside of each LED luminaire unit Yes - REPORTS AND CERTIFICATIONS LED Make OSRAM/NICHIA/CREE SAMSUNG/SEOUL LUMILED/PHILIPS EDISON/SYSKA LUMENMAX - 20/64 EVERLIGHT BRIDGELUX NATIONSTAR/REFOND System must have EMI/EMC compliance as applicable (Test reports shall be furnish on demand by buyer/consignee) Yes - LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government lab/NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-79 report shall have total lumen output

) Yes - LM 80 & TM 21 (Part of LM 80) (Ref. IS:16105:2012) Reports and Photo biological report for LED report from Central Government lab NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-80 report shall haveand the Pohoto Biological report of the LED Chip being used in the luminaire) Yes - Availability of test Report from Central Government lab/NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-5/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes - Seller has to furnish Type test report on demand by buyer/consignee Yes - DC or AC supplied electronic control gear for LED Module shall Yes - 21/64 comlpy as per IS:15885 (Part 2/Sec.13) LED Luminaire for Flood Light shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 5): 2012 as applicable on the date Yes - * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001

Raipur. (C.G.) 8 15 LED Luminaire (for Flood Light) ( 18 ) Technical Specifications Specification Specification Name Values Allowed Values STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 5/2012 latest and IS: 16107 (Part 2/Sec 1):2012 latest Yes - Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes - Types of LED Luminaire as per the IS: 16107(Part-2 Sec.-1)/2012 Type B - Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 - LED Rating/System Wattage/Rated Power 50W 15W

500W Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt - 22/64 Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest IP65 - Mounting brackets (included) Adjustable - Warranty for free replacement (in Years) 2 - ELECTRICAL EFFICIENCY Input operating Voltage range and frequency 90 to 300 V olts AC at 50 Hz+/-2 Hz - Automatic Higher Cut off voltage above 300 volt Yes - Rated voltage 230 V AC 50 Hz - AC Power Factor at full load ≥ 0.95 - Driver Efficiency (in %age) ≥85 - Total Harmonics Distortion (in %age) ≤ 10 - "The total circuit power shall not be more than 110 percent of the value declared by the manufacturer" Yes - OPTICAL LED chip Efficacy ≥130 Lm/Watt - Colour temperature (+/-500K) 6000K - Working life for LED (Minimum 50

000 burning hours as per LM-80 report) Yes - Colour Rendering Index(CRI) ≥70 - Beam Angle ≥120 - Optic lense materal (UV stabilised) (Write NA for without optic lense supply) NA - THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes - Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes - 23/64 Junction temperature < 85 degC - Operating temperature range -10 deg C to +50 deg C - Operating Humidity Range 10 % to 95% RH - PROTECTION Short circuit Protection Yes - Over load protecton Yes - Over Voltage protection Yes - Reverse polarity Yes - High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes - Insulation resistance between earth and current carrying part >100 M ohm - The luminaire shall be protected against surges and transients ( Internal) >/=4KV - The luminaire shall be protected against surges and transients of >/=10KV (External) No - CONSTRUCTIONAL The Luminaires casing/housing (single piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity Yes - The luminaire body must be corrosion resistant epoxy powder coated Yes - All fastners must be of stainless steel Yes - The entire housing (both LED section and driver section) shall be dust and water proof having IP 66 protection as per IS:10322 (Part 1):1982 latest Yes - Extruded silicon loop gasket shall be provided in the lantern body to ensure a Yes - 24/64 weather proof seal between the UV Glass cover and the metal housing to exclude the entry of the dust

and lot Yes - 25/64 number as identification mark inside each unit and the outside of each packaging box The operation characteristics voltage and power be marked inside of each LED luminaire unit Yes - REPORTS AND CERTIFICATIONS LED Make OSRAM/NICHIA/CREE SAMSUNG/SEOUL LUMILED/PHILIPS EDISON/SYSKA LUMENMAX EVERLIGHT BRIDGELUX NATIONSTAR/REFOND - System must have EMI/EMC compliance as applicable (Test reports shall be furnish on demand by buyer/consignee) Yes - LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government lab/NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-79 report shall have total lumen output

) Yes - LM 80 & TM 21 (Part of LM 80) (Ref. IS:16105:2012) Reports and Photo biological report for LED report from Central Government lab NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-80 report shall haveand the Pohoto Biological report of the LED Chip being used in the luminaire) Yes - Availability of test Report from Central Yes - 26/64 Government lab/NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-5/2012 and IS 16107 (Part 2/Sec 1) : 2012 Seller has to furnish Type test report on demand by buyer/consignee Yes - DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes - LED Luminaire for Flood Light shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 5): 2012 as applicable on the date Yes - * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001

Raipur. (C.G.) 18 15 LED Luminaire (for Flood Light) ( 4 ) Technical Specifications Specification Specification Name Values Allowed Values STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 5/2012 latest and IS: 16107 (Part 2/Sec 1):2012 latest Yes - Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes - Types of LED Luminaire Type B - 27/64 as per the IS: 16107(Part-2 Sec.-1)/2012 Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 - LED Rating/System Wattage/Rated Power 50W 15W

000 burning hours as per LM-80 report) Yes - Colour Rendering Index(CRI) ≥70 - Beam Angle ≥120 - 28/64 Optic lense materal (UV stabilised) (Write NA for without optic lense supply) NA - THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes - Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes - Junction temperature < 85 degC - Operating temperature range -10 deg C to +55 deg C - Operating Humidity Range 10 % to 95% RH - PROTECTION Short circuit Protection Yes - Over load protecton Yes - Over Voltage protection Yes - Reverse polarity Yes - High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes - Insulation resistance between earth and current carrying part >100 M ohm - The luminaire shall be protected against surges and transients ( Internal) >/=4KV - The luminaire shall be protected against surges and transients of >/=10KV (External) No - CONSTRUCTIONAL The Luminaires casing/housing (single piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity Yes - The luminaire body must be corrosion resistant epoxy powder coated Yes - 29/64 All fastners must be of stainless steel Yes - The entire housing (both LED section and driver section) shall be dust and water proof having IP 66 protection as per IS:10322 (Part 1):1982 latest Yes - Extruded silicon loop gasket shall be provided in the lantern body to ensure a weather proof seal between the UV Glass cover and the metal housing to exclude the entry of the dust

Neutral and Earth) Yes - Suitable connector shall be provided for LED connection between driver output and LED Yes - Length of ISI marked three core wire (shall be provided along with 50 cm - 30/64 supply of material) Light Source SMD LED Chip as per LM 80/IS16106 - MARKING "Manufactures Name and and brand on the aluminium die cast body Engraved/Embossed - Manufacturer’s name

) Yes - LM 80 & TM 21 (Part of LM 80) (Ref. IS:16105:2012) Reports and Photo biological Yes - 31/64 report for LED report from Central Government lab NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-80 report shall haveand the Pohoto Biological report of the LED Chip being used in the luminaire) Availability of test Report from Central Government lab/NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-5/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes - Seller has to furnish Type test report on demand by buyer/consignee Yes - DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes - LED Luminaire for Flood Light shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 5): 2012 as applicable on the date Yes - * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001

Raipur. (C.G.) 4 15 LED Luminaire (For Road And Street Lights) ( 6 ) Technical Specifications 32/64 Specification Specification Name Values Allowed Values STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 3/2012 latest and IS: 16107 (Part 2/Sec 1):2012 latest Yes - Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes - Types of LED Luminaire as per the IS: 16107(Part-2 Sec.-1)/2012 Type B - Types of LED Modules as per the IS:IS: 16103(Part-2)/2012 Type 3 - LED Rating (in Watts)/System Wattage/Rated Power 45W - Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt - Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest IP66 - Warranty for free replacement (in years) 2 - ELECTRICAL EFFICIENCY Input operating Voltage range and frequency 90 to 300 Volts AC at 50 Hz+/-2 - Automatic Higher Cut off voltage above 300 volt Yes - Rated voltage 230 V AC 50 Hz - AC Power Factor at full load ≥ 0.95 - Driver Efficiency (in %age) Upto 100W: ≥85%

Above 100W: >/=90% Yes - Total Harmonics Distortion ≤ 10 - "The total circuit power shall not be more than 110 percent of the value declared by the manufacturer (as per Cl. 8 of IS:16104:2012 lates)" Yes - 33/64 OPTICAL LED chip Efficacy ≥130 Lm/Watt - Colour temperature 6000+/-500K - Working life for LED (Minimum 50

000 burning hours as per LM-80 and LM 21 reports) Yes - Colour Rendering Index(CRI) ≥70 - LED Beam Angle ≥120 - Optic lense materal (UV stabilised) Poly carbonate lense - THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes - Junctiojn/Soldering point temperature shall not exceed 85 deg.c as per LM 80 report Yes - Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes - Operating temperature range -10 deg C to +55 deg C - Operating Humidity Range 10 % to 95% RH - PROTECTION Short circuit Protection Yes - Over load protecton Yes - Over Voltage protection Yes - Reverse polarity Yes - High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes - Insulation resistance between earth and current carrying part >100 M Ohm - The luminaire shall be protected against surges and transients ( Internal) >/=4KV - The luminaire shall be protected against surges and transients No - 34/64 of >/=10KV (External) CONSTRUCTIONAL The Luminaires casing/housing (single piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity Yes - The luminaire body must be corrosion resistant powder coated Yes - All fastners must be of stainless steel Yes - Protection of the entire housing (both LED section and driver section) as per IS:10322 (Part 1):1982 latest IP66 - Extruded silicon loop gasket shall be provided in the lantern body to ensure a weather proof seal between the UV Glass cover and the metal housing to exclude the entry of the dust

Yes - Luminaries light transparency should be of Toughened glass Yes - Toughned transparent glass cover thickness >/=4 mm - Toughned Glass shall not get discoloured shall not suffer degration due to heat and ageing within warranty period Yes - Number of electronic control gear (power supplies) 1 No. - Light Source SMD LED Chip as per LM 80/IS16106 - Driver components shall be industrial grade or above Yes - PCB shall be FR4 grade minimum 0.8 to 1.0 Yes - 35/64 mm thick or more The Luminaires works on single phase three wires system (Phase

Neutral and Earth) Yes - Suitable connector shall be provided for LED connection between driver output and LED Yes - Length of ISI marked three core wire (shall be provided along with supply of material) 50 cm - MARKING "Manufactures Name and and brand on the aluminium die cast body " Engraved/Embossed - Manufacturer’s name

and lot number as identification mark inside each unit and the outside of each packaging box Yes - The operation characteristics voltage and power be marked inside of each LED luminaire unit Yes - Diameter of pole Luminiare suitable for: (upto 45W Pole OD: shall be 40mm)

(>45W<120W Pole OD: Shall be 50 mm)

(above 120W: OD shall be 60 mm for which luminiare is suitable Yes - REPORTS AND CERTIFICATIONS LED Make OSRAM/NICHIA/CREE SAMSUNG/SEOUL LUMILEDS/PHILIPS SYSKA/LUMENMAX EVERLIGHT/EDISON BRIDGELUX NATIONSTAR/REFOND - System must have EMI/EMC compliance as applicable (Test reports Yes - 36/64 shall be furnish to the buyer/consignee on demand) LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer consignee on demand (LM-79 report shall have total lumen output

) Yes - LM 80 & TM 21 (Ref. IS:16105:2012) Report and Photo biological report for LED report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer consignee on demand (LM-80 report shall have the Pohoto Biological report of the LED Chip being used in the luminaire) Yes - Availability of test Report from Central Government Lab NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-3/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes - Seller shall furnish the Type test reports to the buyer/consignee on demand Yes - DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes - LED Luminaire for road and street lighting shall comply with Complusory Registration(CRS) of Yes - 37/64 BIS for safety as per IS 10322 (Part 5/Section 3): 2012 as applicable on date * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001

Raipur. (C.G.) 6 15 LED Luminaire (For Road And Street Lights) ( 12 ) Technical Specifications Specification Specification Name Values Allowed Values STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 3/2012 latest and IS: 16107 (Part 2/Sec 1):2012 latest Yes - Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes - Types of LED Luminaire as per the IS: 16107(Part-2 Sec.-1)/2012 Type B - Types of LED Modules as per the IS:IS: 16103(Part-2)/2012 Type 3 - LED Rating (in Watts)/System Wattage/Rated Power 60W - Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt - Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest IP66 - Warranty for free replacement (in years) 2 - ELECTRICAL EFFICIENCY Input operating Voltage range and frequency 90 to 300 Volts AC at 50 Hz+/-2 - Automatic Higher Cut Yes - 38/64 off voltage above 300 volt Rated voltage 230 V AC 50 Hz - AC Power Factor at full load ≥ 0.95 - Driver Efficiency (in %age) Upto 100W: ≥85%

Above 100W: >/=90% Yes - Total Harmonics Distortion ≤ 10 - "The total circuit power shall not be more than 110 percent of the value declared by the manufacturer (as per Cl. 8 of IS:16104:2012 lates)" Yes - OPTICAL LED chip Efficacy ≥130 Lm/Watt - Colour temperature 6000+/-500K - Working life for LED (Minimum 50

000 burning hours as per LM-80 and LM 21 reports) Yes - Colour Rendering Index(CRI) ≥70 - LED Beam Angle ≥120 - Optic lense materal (UV stabilised) Poly carbonate lense - THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes - Junctiojn/Soldering point temperature shall not exceed 85 deg.c as per LM 80 report Yes - Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes - Operating temperature range -10 deg C to +55 deg C - Operating Humidity Range 10 % to 95% RH - PROTECTION Short circuit Protection Yes - 39/64 Over load protecton Yes - Over Voltage protection Yes - Reverse polarity Yes - High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes - Insulation resistance between earth and current carrying part >100 M Ohm - The luminaire shall be protected against surges and transients ( Internal) >/=4KV - The luminaire shall be protected against surges and transients of >/=10KV (External) No - CONSTRUCTIONAL The Luminaires casing/housing (single piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity Yes - The luminaire body must be corrosion resistant powder coated Yes - All fastners must be of stainless steel Yes - Protection of the entire housing (both LED section and driver section) as per IS:10322 (Part 1):1982 latest IP66 - Extruded silicon loop gasket shall be provided in the lantern body to ensure a weather proof seal between the UV Glass cover and the metal housing to exclude the entry of the dust

Yes - Luminaries light transparency should be of Toughened glass Yes - 40/64 Toughned transparent glass cover thickness >/=4 mm - Toughned Glass shall not get discoloured shall not suffer degration due to heat and ageing within warranty period Yes - Number of electronic control gear (power supplies) 1 No. - Light Source SMD LED Chip as per LM 80/IS16106 - Driver components shall be industrial grade or above Yes - PCB shall be FR4 grade minimum 0.8 to 1.0 mm thick or more Yes - The Luminaires works on single phase three wires system (Phase

and lot number as identification mark inside each unit and the outside of each packaging box Yes - The operation characteristics voltage and power be marked inside of each LED luminaire unit Yes - 41/64 Diameter of pole Luminiare suitable for: (upto 45W Pole OD: shall be 40mm)

(above 120W: OD shall be 60 mm for which luminiare is suitable Yes - REPORTS AND CERTIFICATIONS LED Make OSRAM/NICHIA/CREE SAMSUNG/SEOUL LUMILEDS/PHILIPS SYSKA/LUMENMAX EVERLIGHT/EDISON BRIDGELUX NATIONSTAR/REFOND - System must have EMI/EMC compliance as applicable (Test reports shall be furnish to the buyer/consignee on demand) Yes - LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer consignee on demand (LM-79 report shall have total lumen output

) Yes - LM 80 & TM 21 (Ref. IS:16105:2012) Report and Photo biological report for LED report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer consignee on demand (LM-80 report shall have the Pohoto Biological report of the LED Chip being used in the luminaire) Yes - Availability of test Report from Central Government Lab NABL/ILAC accrediated Yes - 42/64 lab to Indian Standrad IS:10322/part 5/sec-3/2012 and IS 16107 (Part 2/Sec 1) : 2012 Seller shall furnish the Type test reports to the buyer/consignee on demand Yes - DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes - LED Luminaire for road and street lighting shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 3): 2012 as applicable on date Yes - * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001

Raipur. (C.G.) 12 15 LED Luminaire (Recessed Luminaire) ( 5 ) Technical Specifications Specification Specification Name Values Allowed Values STANDARDS Conformity to Indian Standard IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 for Recess type - Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes - DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes - 43/64 Luminaire Class (as per Cl. 2.1 Section 2 of IS: 10322 (Part-1) Class I - Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 - Rating of Recess type LED Luminaire/System Wattage/Rated Power 16W - Light Intensity(System Lumens) 80 Lm/Watt for 3000 deg K

90 Lm/Watt for 4000 deg K

100 Lm/Watt for 6000 deg K Yes - Color temeprature (+/- 500 K) 6000 deg K - Type of fixture (in feet) 1x1 (for 3W to 16W) - CONSTRUCTIONAL Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest (Minimum) IP20 - Mounting type Recess type - Diffuser material Acrylic - The luminaire body must be corrosion resistant epoxy powder coated/anadozing Yes - All fastners must be of nickel/chrome plated Yes - Number of electronic control gear (power supplies) 1 - Light Source SMD LED Chip as per LM 80/IS16106 - Warranty for free replacement 2 Years - ELECTRICAL EFFICIENCY MANAGEMENT Operating Voltage and frequency range 140V to 280 V at 50 Hz AC - Rated voltage 230 V AC 50 Hz - AC Power Factor ≥ 0.90 - Driver Efficiency ≥85 - Total Harmonics Distortion ( ≤ 20% (for upto 20W) (</=10% (for above 20W) Yes - The total circuit power Yes - 44/64 shall not be more than 110 percent of the value declared by the manufacturer (as per Cl 8 of IS:16104:2012 lates) OPTICAL MANAGEMENT LED chip Efficacy (≥130 Lm/Watt for 6000 deg K

>/=120 Lm/Watt for 4000 deg K

>/=110 Lm/Watt for 3000 deg K) Yes - Working life for LED : (Minimum 50

000 burning hours as per LM-80 report) Yes - Colour Rendering Index(CRI) ≥80 - Beam Angle ≥120 - Reflector type Diffuser - THERMAL MANAGEMENT Fixture/Luminaire should be die-cast aluminium CRCA/Extruded aluminium Yes - Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes - Junction temperature soldering temperature < 85 deg C - Operating temperature range -10 deg. C to +55 deg. C - Humidity Range 10 % to 95% RH - PROTECTION Short circuit Protection Yes - Over load protecton Yes - High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes - Insulation resistance between earth and current carrying part >100 M ohm - The luminaire shall be protected against surges and transients of >/=2.5 KV Yes - MARKING Manufactures Name Engraved/Embssed - 45/64 and brand shall available on the body of the Luminaire Each LED liminaire shall have the manufacturer’s name

serial number

date of manufacture (month- year)

and lot number as identification mark inside each unit and the outside of each packaging box Yes - The operation characteristics such as rated voltage and rated power in watts shall be marked inside each LED luminaire unit Yes - REPORTS AND CERTIFICATIONS LED Make EVERLIGHT/EDISON BRIDGELUX NATIONSTAR/SEOUL SAMSUNG/OSRAM REFOND/NICHIA CREE/LUMILEDS PHILIPS/SYSKA LUMENMAX - LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government LAB NABL/ILAC accrediated lab. Reports shall be furnish to the buyer on demand (LM-79 report shall have total lumen output

) Yes - LM 80 &TM21(Ref. IS:16105:2012) Report and Photo biological report for LED report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer on demand (LM-80 report shall have the Photo Biological report of the LED Chip being used in the luminaire) Yes - 46/64 Availability of test Report from Central Government Lab NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes - Seller has to furnish Type test report to the buyer on demand Yes - DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes - LED Luminaire for rcess type shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 2): 2012 as applicable on date Yes - * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001

Raipur. (C.G.) 5 15 LED Luminaire (Recessed Luminaire) ( 5 ) Technical Specifications Specification Specification Name Values Allowed Values STANDARDS Conformity to Indian Standard IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 for Recess type - Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes - DC or AC supplied electronic control gear for LED Module shall Yes - 47/64 comlpy as per IS:15885 (Part 2/Sec.13) Luminaire Class (as per Cl. 2.1 Section 2 of IS: 10322 (Part-1) Class I - Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 - Rating of Recess type LED Luminaire/System Wattage/Rated Power 18W - Light Intensity(System Lumens) 80 Lm/Watt for 3000 deg K

100 Lm/Watt for 6000 deg K Yes - Color temeprature (+/- 500 K) 6000 deg K - Type of fixture (in feet) 1x4 (30W to 48W) - CONSTRUCTIONAL Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest (Minimum) IP20 - Mounting type Recess type - Diffuser material Acrylic - The luminaire body must be corrosion resistant epoxy powder coated/anadozing Yes - All fastners must be of nickel/chrome plated Yes - Number of electronic control gear (power supplies) 1 - Light Source SMD LED Chip as per LM 80/IS16106 - Warranty for free replacement 2 Years - ELECTRICAL EFFICIENCY MANAGEMENT Operating Voltage and frequency range 140V to 280 V at 50 Hz AC - Rated voltage 230 V AC 50 Hz - AC Power Factor ≥ 0.90 - Driver Efficiency ≥85 - Total Harmonics Distortion ( ≤ 20% (for upto 20W) (</=10% Yes - 48/64 (for above 20W) The total circuit power shall not be more than 110 percent of the value declared by the manufacturer (as per Cl 8 of IS:16104:2012 lates) Yes - OPTICAL MANAGEMENT LED chip Efficacy (≥130 Lm/Watt for 6000 deg K

000 burning hours as per LM-80 report) Yes - Colour Rendering Index(CRI) ≥80 - Beam Angle ≥120 - Reflector type Diffuser - THERMAL MANAGEMENT Fixture/Luminaire should be die-cast aluminium CRCA/Extruded aluminium Yes - Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes - Junction temperature soldering temperature < 85 deg C - Operating temperature range -10 deg. C to +55 deg. C - Humidity Range 10 % to 95% RH - PROTECTION Short circuit Protection Yes - Over load protecton Yes - High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes - Insulation resistance between earth and current carrying part >100 M ohm - The luminaire shall be protected against surges and transients Yes - 49/64 of >/=2.5 KV MARKING Manufactures Name and brand shall available on the body of the Luminaire Engraved/Embssed - Each LED liminaire shall have the manufacturer’s name

) Yes - LM 80 &TM21(Ref. IS:16105:2012) Report and Photo biological report for LED report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer on demand (LM-80 report shall have the Photo Biological report of the Yes - 50/64 LED Chip being used in the luminaire) Availability of test Report from Central Government Lab NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes - Seller has to furnish Type test report to the buyer on demand Yes - DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes - LED Luminaire for rcess type shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 2): 2012 as applicable on date Yes - * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001

Raipur. (C.G.) 5 15 LED Luminaire (Recessed Luminaire) ( 15 ) Technical Specifications Specification Specification Name Values Allowed Values STANDARDS Conformity to Indian Standard IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 for Recess type - Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes - 51/64 DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes - Luminaire Class (as per Cl. 2.1 Section 2 of IS: 10322 (Part-1) Class I - Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 - Rating of Recess type LED Luminaire/System Wattage/Rated Power 3W - Light Intensity(System Lumens) 80 Lm/Watt for 3000 deg K

100 Lm/Watt for 6000 deg K Yes - Color temeprature (+/- 500 K) 6000 deg K - Type of fixture (in feet) 1x1 (for 3W to 16W) - CONSTRUCTIONAL Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest (Minimum) IP20 - Mounting type Recess type - Diffuser material Acrylic - The luminaire body must be corrosion resistant epoxy powder coated/anadozing Yes - All fastners must be of nickel/chrome plated Yes - Number of electronic control gear (power supplies) 1 - Light Source SMD LED Chip as per LM 80/IS16106 - Warranty for free replacement 2 Years - ELECTRICAL EFFICIENCY MANAGEMENT Operating Voltage and frequency range 140V to 280 V at 50 Hz AC - Rated voltage 230 V AC 50 Hz - AC Power Factor ≥ 0.90 - Driver Efficiency ≥85 - 52/64 Total Harmonics Distortion ( ≤ 20% (for upto 20W) (</=10% (for above 20W) Yes - The total circuit power shall not be more than 110 percent of the value declared by the manufacturer (as per Cl 8 of IS:16104:2012 lates) Yes - OPTICAL MANAGEMENT LED chip Efficacy (≥130 Lm/Watt for 6000 deg K

000 burning hours as per LM-80 report) Yes - Colour Rendering Index(CRI) ≥80 - Beam Angle ≥120 - Reflector type Diffuser - THERMAL MANAGEMENT Fixture/Luminaire should be die-cast aluminium CRCA/Extruded aluminium Yes - Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes - Junction temperature soldering temperature < 85 deg C - Operating temperature range -10 deg. C to +55 deg. C - Humidity Range 10 % to 95% RH - PROTECTION Short circuit Protection Yes - Over load protecton Yes - High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes - Insulation resistance between earth and current carrying part >100 M ohm - 53/64 The luminaire shall be protected against surges and transients of >/=2.5 KV Yes - MARKING Manufactures Name and brand shall available on the body of the Luminaire Engraved/Embssed - Each LED liminaire shall have the manufacturer’s name

) Yes - LM 80 &TM21(Ref. IS:16105:2012) Report and Photo biological report for LED report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer on Yes - 54/64 demand (LM-80 report shall have the Photo Biological report of the LED Chip being used in the luminaire) Availability of test Report from Central Government Lab NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes - Seller has to furnish Type test report to the buyer on demand Yes - DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes - LED Luminaire for rcess type shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 2): 2012 as applicable on date Yes - * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001

Raipur. (C.G.) 15 15 LED Luminaire (Recessed Luminaire) ( 6 ) Technical Specifications Specification Specification Name Values Allowed Values STANDARDS Conformity to Indian Standard IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 for Recess type - Photo biological safety of LEDs used shall be Yes - 55/64 as per IS:16108/2012 (exempt group) DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes - Luminaire Class (as per Cl. 2.1 Section 2 of IS: 10322 (Part-1) Class I - Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 - Rating of Recess type LED Luminaire/System Wattage/Rated Power 6W - Light Intensity(System Lumens) 80 Lm/Watt for 3000 deg K

100 Lm/Watt for 6000 deg K Yes - Color temeprature (+/- 500 K) 6000 deg K - Type of fixture (in feet) 1x2 (3W to 16W) - CONSTRUCTIONAL Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest (Minimum) IP20 - Mounting type Recess type - Diffuser material Acrylic - The luminaire body must be corrosion resistant epoxy powder coated/anadozing Yes - All fastners must be of nickel/chrome plated Yes - Number of electronic control gear (power supplies) 1 - Light Source SMD LED Chip as per LM 80/IS16106 - Warranty for free replacement 2 Years - ELECTRICAL EFFICIENCY MANAGEMENT Operating Voltage and frequency range 140V to 280 V at 50 Hz AC - Rated voltage 230 V AC 50 Hz - AC Power Factor ≥ 0.90 - 56/64 Driver Efficiency ≥85 - Total Harmonics Distortion ( ≤ 20% (for upto 20W) (</=10% (for above 20W) Yes - The total circuit power shall not be more than 110 percent of the value declared by the manufacturer (as per Cl 8 of IS:16104:2012 lates) Yes - OPTICAL MANAGEMENT LED chip Efficacy (≥130 Lm/Watt for 6000 deg K

000 burning hours as per LM-80 report) Yes - Colour Rendering Index(CRI) ≥80 - Beam Angle ≥120 - Reflector type Diffuser - THERMAL MANAGEMENT Fixture/Luminaire should be die-cast aluminium CRCA/Extruded aluminium Yes - Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes - Junction temperature soldering temperature < 85 deg C - Operating temperature range -10 deg. C to +55 deg. C - Humidity Range 10 % to 95% RH - PROTECTION Short circuit Protection Yes - Over load protecton Yes - High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes - Insulation resistance between earth and >100 M ohm - 57/64 current carrying part The luminaire shall be protected against surges and transients of >/=2.5 KV Yes - MARKING Manufactures Name and brand shall available on the body of the Luminaire Engraved/Embssed - Each LED liminaire shall have the manufacturer’s name

) Yes - LM 80 &TM21(Ref. IS:16105:2012) Report and Photo biological report for LED report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be Yes - 58/64 furnish to the buyer on demand (LM-80 report shall have the Photo Biological report of the LED Chip being used in the luminaire) Availability of test Report from Central Government Lab NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes - Seller has to furnish Type test report to the buyer on demand Yes - DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes - LED Luminaire for rcess type shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 2): 2012 as applicable on date Yes - * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001

Raipur. (C.G.) 6 15 LED Luminaire (Recessed Luminaire) ( 25 ) Technical Specifications Specification Specification Name Values Allowed Values STANDARDS Conformity to Indian Standard IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 for Recess type - Photo biological safety Yes - 59/64 of LEDs used shall be as per IS:16108/2012 (exempt group) DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes - Luminaire Class (as per Cl. 2.1 Section 2 of IS: 10322 (Part-1) Class I - Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 - Rating of Recess type LED Luminaire/System Wattage/Rated Power 36W - Light Intensity(System Lumens) 80 Lm/Watt for 3000 deg K

100 Lm/Watt for 6000 deg K Yes - Color temeprature (+/- 500 K) 6000 deg K - Type of fixture (in feet) 2x2(30W to 48W) - CONSTRUCTIONAL Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest (Minimum) IP20 - Mounting type Recess type - Diffuser material Acrylic - The luminaire body must be corrosion resistant epoxy powder coated/anadozing Yes - All fastners must be of nickel/chrome plated Yes - Number of electronic control gear (power supplies) 1 - Light Source SMD LED Chip as per LM 80/IS16106 - Warranty for free replacement 2 Years - ELECTRICAL EFFICIENCY MANAGEMENT Operating Voltage and frequency range 140V to 280 V at 50 Hz AC - Rated voltage 230 V AC 50 Hz - 60/64 AC Power Factor ≥ 0.90 - Driver Efficiency ≥85 - Total Harmonics Distortion ( ≤ 20% (for upto 20W) (</=10% (for above 20W) Yes - The total circuit power shall not be more than 110 percent of the value declared by the manufacturer (as per Cl 8 of IS:16104:2012 lates) Yes - OPTICAL MANAGEMENT LED chip Efficacy (≥130 Lm/Watt for 6000 deg K

000 burning hours as per LM-80 report) Yes - Colour Rendering Index(CRI) ≥80 - Beam Angle ≥120 - Reflector type Diffuser - THERMAL MANAGEMENT Fixture/Luminaire should be die-cast aluminium CRCA/Extruded aluminium Yes - Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes - Junction temperature soldering temperature < 85 deg C - Operating temperature range -10 deg. C to +55 deg. C - Humidity Range 10 % to 95% RH - PROTECTION Short circuit Protection Yes - Over load protecton Yes - High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes - 61/64 Insulation resistance between earth and current carrying part >100 M ohm - The luminaire shall be protected against surges and transients of >/=2.5 KV Yes - MARKING Manufactures Name and brand shall available on the body of the Luminaire Engraved/Embssed - Each LED liminaire shall have the manufacturer’s name

) Yes - LM 80 &TM21(Ref. IS:16105:2012) Report and Photo biological report for LED report from Central Yes - 62/64 Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer on demand (LM-80 report shall have the Photo Biological report of the LED Chip being used in the luminaire) Availability of test Report from Central Government Lab NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes - Seller has to furnish Type test report to the buyer on demand Yes - DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes - LED Luminaire for rcess type shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 2): 2012 as applicable on date Yes - * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001

Raipur. (C.G.) 25 15 EMD Required No ePBG Required No 63/64