COMPREHENSIVE REPAIR TO OTM and MD ACCN UNDER AOR OF D and M BN AT MIC and S UNDER GE(S) AHMEDNAGAR

Amount

Dismantling of Kota stone slab, granite, Cudappah, interlocking paver block and paver tiles of any description in floor, laid, bedded & pointed in any mortar all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) in ground floor & paving n.exc. 15cm thick below or above ground level all as specified and as directed.

Demolition of brick work, stone or block masonry built in cement or lime mortar including all quoins, arches, pillars, etc all as specified and as directed.

Taking down cement plaster of any description on brick or stone walls etc., including raking out joints, hacking for key, scrubbing down with water etc., complete all as specified and as directed.

Taking down shutters of any description, area exc 1 sqm but not exc 2 sqm each all as specified and as directed.

Taking down shutters of any description exc 1 sqm and n exc 2 sqm and refixing in the same opening complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames), area not exc 1.5 sq. m each all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames), area exc 1.5 sq. m but not exc 4 sqm each all as specified and as directed.

Dismantling asbestos cement (corrugated, Semi-corrugated etc.) sheets in roof coverings all as specified and as directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing all as specified and as directed.

Taking up or down 25 mm bore steel tubing and connections, including cleaning for refixing all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Excavation over areas n exc 1.5m in depth in soft/loose soil for foundation etc all as specified and directed.

Excavation in trenches not exc 1.50 m wide and not exc 1.50 m deep for foundation etc or laying of pipe or for shafts, wells cesspits,man holes etc not exc 10 Sqm on plan and n exc 1.5m in depth and getting out in soft / loose soil complete all as specified and as directed.

Removing excavated soil to distance not exc. 50 m and depositing where directed at a level not exc. 1.5 m above the starting point etc complete all as specified and as directed.

M&L for moorum filling in floors or paving, laid in layers n.exc. 15cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for hard core of gauge exc. 63 mm but n. exc. 100 mm, deposited spread and levelled in layers n. exc. 15cm thick, including watering and rammed etc. complete all as specified and as directed.

M&L for plain cement concrete, 1:4:8 type D2 (using 40mm graded stone aggregates) as in foundation, filling and mass concrete etc. complete all as specified and as directed.

M&L for reinforced cement concrete, type B-1, 1:2:4, using 20 mm graded stone aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete all as specified and as directed.

M&L for precast cement concrete block masonry with solid block of PCC (1:5:8) , exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work sub class 'B' bricks, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6, complete all as specified and as directed.

All as per item No. 23 here-in-before but except bricks. Note : Serviceable bricks obtained from demolition shall be reused.

M&L for cutting chases for pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth concealed water tubing all as specified and as directed.

S&F 35 mm thick, second class hard wood glazed and skeleton shutters, factory made, open rebated and prepared to receive glass, gauze, etc., divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamferesd or rounded, fitted with cut and mitred beads for securing glass etc., for windows and ventilators, etc are provided with stiles and rails as specified in SSR Pt I Section 8, clause 8.24 (a) complete all as specified and as directed.

S&F 35 mm thick, second class hard wood, plain framed, factory made, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and as directed.

S&F of solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC Sheet reiforced with M.S. Square tube , supplying & fixing in openning as per specification all as specified and as directed.

S&F Fatory made solid panel PVC door shutter, 30mm thick(stiles), consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded feathered edges plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struk inside with solvent cement for stiles and plain colour feathered edges PVC sheet for top rail,lock rail and bottom rail on either side & as gap insert for top rail & bottom rail, panneling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles & rails with suitable for feathered edges PVC sheet, and jointed together with solvent cement, suppling and fixing in the frame at site as per specification & drawing all as specified and as directed.

S&F 150 mm size aluminium anodised, barrel tower bolts of extruded section and fixed all as specified and as directed.

S&F 250 mm long aluminum alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of steel, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy complete all as specified and as directed.

S&F 100 mm size butt hinges medium weight, cold rolled, mild steel, and fixed all as specified and as directed.

S&F 100 mm size butt hinges medium weight, stainless steel, and fixed all as specified and as directed.

S&F in repairs, 300mm size, mild steel ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and as directed.

S&F 125 mm size extruded aluminium alloy handles, fabricated type, anodised all as specified and as directed.

S&F in repairs drapery / curtain rod with brackets and knobs at both ends made out of 25mm dia MS conduit having PVC powder coated pipe having wall thickness 0.63 mm bright finish colour and pattern complete all as specified & as directed. Note: The cost of brackets & knobs shall deemed to be included in the quoted rate.

S&F in repairs 25mm dia stainless steel fancy type curtain rod with brackets and knobs at both ends as per site requirement including taking down old curtain rods with accessories complete all as specified and as directed. Note: The cost of brackets & knobs shall deemed to be included in the quoted rate.

S&F in repairs, tubular towel rail, brass chromium plated, 20 mm dia `D' type, 60 cm long between flanges all as specified and as directed.

S&F 5 inches heavy duty Vanilla door stopper mounted with Rubber tip of aluminium alloy body fixed in floor, all as specified and as directed.

S&F in repairs, galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aparture 1.18 mm, fixed with wooden beads / tinned tacks or galvanised wire staples to steel / wooden frame complete all as specified and as directed.

S&F in repairs, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aparture 1.40 mm, fixed with stainless steel wire staples to steel / wooden frame complete all as specified and as directed.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aparture 1.18 mm, fixed with wooden beads / tinned tacks or galvanised wire staples to steel / wooden frame complete all as specified and as directed.

M&L for mild steel TMT bars 6 to 8 mm dia, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.Fe 410 -W (Gde- E- 250) quality- A all as specified and as directed.

S&F mild steel windows, side hung, including projecting type hinges with steel handles and steel peg stay complete with glazing bars dovetailed or welded complete all as specified and as directed.

S&F mild steel windows, side hung, including projecting type hinges with steel handles and steel peg stay complete without glazing bars dovetailed or welded complete all as specified and as directed.

S&F mild steel ventilators top hung type with glazing bars all as specified and as directed.

S&F mild steel ventilators fixed type with glazing bars all as specified and as directed.

S&F mild steel framed work such as grills, framed guard bars and similar work, with ends of bars shouldered and/or rivetted, or forged into spikes; framed guard bars, barred iron doors, ladders, framedballusters, walk ways, railings, frame work of water tank and similarwork conforming to Fe-290.Gde-E-165, welded to steel ventilators & window complete all as specified and as directed.

S&F pressed steel doors frames of size 105 mm x 60 mm x 1.25mm thick, with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified and as directed.

M&L for welding in repairs, n exc 2.5 cm in length, thickness of metal to be welded n. exc 6 mm complete all as specified and as directed.

S&F powder coated aluminium door with frame and shutter in two panels (top and bottom) made out of aluminium sections (make Jindal or equivalent) including 5 mm thick sheet glass, aluminium cleats, rubber/ neoprene beading, all necessary fittings and locking arrangements etc all as specified and as directed and comprises of following sections :- (a) Vertical style and top rail - 47 x 44.5 x 2.25 mm thick @ 1.15 Kg/m (Min) (b) Lock rail- 114.6 x 44.45 x 2.3mm thick @ 2.06 Kg/m (Min) (c) Bottom rail- 114.6 x 44.45 x 2.3mm thick @ 2.06 Kg/m (Min) (d) Frame- 47.5 x 44.45 x 2.25 mm thick @ 1.12 Kg/m (Min)

S&F powder coated aluminum windows, three track, made out of aluminium sections (make Jindal or equivalent) including all necessary fittings, 5mm thick sheet glass, rubber/ neoprene beading, locking arrangements all as specified and as directed and comprises of following sections :- (a) Window frame (i) Bottom-Section 20671 (Wt not less than 0.699 Kg/m) (ii) Top & Size - 20672 (Wt not less than 0.594 Kg/m) (b) Shutter (i) Vertical (end)- 20669 (Wt not less than 0.481 Kg/m) (ii) Vertical (lock) - 20689 (Wt not less than 0.481 Kg/m) (iii) Bottom - 20718 (Wt not less than 0.263 Kg/m) (iv) Top - 20668 (Wt not less than 0.377 Kg/m)

S&F laminated Gypsum tile board 8mm thick with textured white colour PVC film on the face side and metalized polyster (MPL) film on rear side in ceiling as per manufacturers instructions of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, including dismantling existing false ceiling anf framework complete for all heights as per specifications, drawings and as directed.

M&L for prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and as directed. Note : Colour, pattern and design shall be as approved by GE.

M&L for prepainted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of colour as approved by GE, having tensile strength of 550 Mpa as in roof covering/ridges/valley gutters/cladding to wall, fixed with self tapping screws as specified and as directed. Note : Colour shall be as approved by GE.

M&L for 6mm thick asbestos cement, corrugated or semi corrugated sheets in roof, wall cladding, fixed with 'L' type or 'J' type or cranked hook bolts, washer etc complete all as specified and as directed.

All as per serial item No 57 but except asbesos cement sheets. Note : Serviceable asbestos sheets obtained from dismantling shall be reused.

Water proofing treatment to floor & vertical surfaces of sunken portion complete comprising the following :- (a) After demolition of floor and lime concrete etc. remove all loose particles along with existing water proofing treatment (any no. of layers) with wire brushes and cleaning the surfaces with water. (b) Brushing cement slurry with 1.2 kg of cement per square meter duly blended with & including water proofing compound. (c) 15mm thick (Average thickness) plaster in cement mortar (1:4) mixed with WP compound on sunken surface including walls. The corner of sunken portion shall be rounded in concave shape and adequate slope shall be made during plastering to accommodate sump pipe and curing the sunken portion with water minimum for 48 Hrs by ponding. (d) Applying self adhesive type APP based polymeric membrane minimum weighing not less than 3.6 kg/sqm and minimum 3 mm thick reinforced with polyster non-woven fabric (weight not less than 150 gm/sqm (e) M&L for PCC 1:7:12 for fillin of sunken portion after conceling all membrane and sealing all joints to the entire with broken bats and light weight, floor area of WC/Bath not exceedding 3.00 sqm and provide hole in the wall and fix 600 mm long 20 mm dia GI spouts light grade, PCC 1:3:6, type C1 (using 20 mm graded stone aggregates) filling complete all as satisfaction of Engineer-in-Charge. Note- The rates include for drilling of the hole RCC @ 1.00 m centre to centre, to a depth to a length of 30 mm and fixing of PVC pipes of dia 15/20 mm laid dry and grouting with cement slurry mixed with can bax 100 chemical with pressure grouting with minimm 3 Kg/Sqm complete all as specified and directed

M&L in repairs, for water proofing treatment to RCC roof slab, including parapet, comprising with the following treatment/specification from bottom to top:- (i) Taking out old roof treatment and roughening the old concrete slab by picking, sweeping clean and washing down with water to remove dust etc and disposal of rubbish n exceeding 100 mtr distance from starting point. (ii) Screed bed or bedding layer of 10 mm thick cement mortar 1:4 with mixing of WPC @ 3% by weight of cement or as per manufacturers instructions and surface finished even and smooth without using extra cement after applying a coat of cement slurry @ 3 kg/sqm for laying APP membrane. (iii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.30 ltr /Sqm conforming to IS:3384-1986. (iv) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 150 gms/Sqm) shall be applied over bituminous primer as specified above by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. (v) Applying two coat of aluminium paint over the APP modified membrane @ 0.11Kg/sqm. Note: Water proofing compount shall be measured & paid seperately.

Supply only water proofing compound complete, ISI mark all as specified and as directed.

M&L for machine cut kota stone flooring, 20-25 mm thick (size of kota stone slab 22"x22") laid over and including 20 mm thick bedding layer of cement mortar 1:6 jointed with grey cement slurry mixed with pigments to match the shade of slab including cutting, rubbing and mirror polishing including removing dust complete all as specified and as directed.

All as per serial item No. 62 but 18 to 20 mm thick kota stone on vertical surfaces such as in skiting /dado of size as required at site over and including10 mm thick backing coat of cement mortar (1:4) complete all as specified and as directed.

M&L for 18 to 20mm thick prepolished granite stone slab as in table top, top of WHB, kitchen slab/platform, steps, gate pillars, cills etc or on vertical surfaces including vertical projection, including full round moulding the edge, laid over and including screed bed 15mm thick in cement mortar 1:4, jointing , pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite and rubbing polish to achieve mirror finish complete all as specified and as directed. Note : Colour and shade of granite shall be as approved by GE.

M&L for machine cut cudappah stone slab 18 -20 mm thick laid over and including cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed.

M&L for 75mm thick, plain cement concrete, 1:4:8, type D-2, using 40 mm graded stone aggregate as in sub base of floor all as specified and as directed.

M&L for 100mm thick, plain cement concrete, 1:4:8, type D-2, using 40 mm graded stone aggregate as in sub base of floor all as specified and as directed.

M&L for glazed coloured ceramic tiles of size 450x300x7mm thick in vertical surface of walls, colour/shade as approved by GE, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tiles over & including 10mm thick rendering in cment mortar 1:4 on other then fair faces of brick work wall finished rough to fix tiles complete all as specified & as directed.

M&L for non skid coloured ceramic tiles 7-8mm thick (square or rectingular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc, color/shade as approved by GE, set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles over & including 15mm thick screed bed in cement mortar 1:6 complete all as specified & as directed.

M&L for vitrified coloured tiles, 8-9 mm thick (square / rectangular), area of each tile n exc 0.36 sqm, shade as approved by GE in floor etc laid over and including 20 mm thick bedding layer in cement mortar 1:6, jointed in grey cement slurry and pointed in white or coloured cement to match with colour of tiles all as specified and as directed.

All as per serial item No 71 but in dado / skirting or on vertical surfaces, laid over and including 10 mm thick backing coat in cement mortar 1:4 .

M&L for double charged vitrified coloured tiles, 8-9 mm thick (square / rectangular), area of each tile n exc 0.36 sqm, shade as approved by GE in floor etc laid over and including 20 mm thick bedding layer in cement mortar 1:6, jointed in grey cement slurry and pointed in white or coloured cement to match with colour of tiles all as specified and as directed.

All as per serial item No 73 but in dado / skirting or on vertical surfaces, laid over and including 10 mm thick backing coat in cement mortar 1:4 .

M&L for non skid coloured ceramic tiles 7-8mm thick (square or rectingular) area of each tile exc 0.11 sqm but not exc 0.18 sqm in floors etc, colour/shade as approved by GE, set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles over & including 15mm thick screed bed in cement mortar 1:6 complete all as specified & as directed.

M&L for non skid coloured ceramic tiles 7-8mm thick (square or rectingular) area of each tile exc 0.18 sqm but not exc 0.38 sqm in floors etc, color/shade as approved by GE, set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles over & including 15mm thick screed bed in CM 1:6 complete all as specified & directed.

All as per serial item No 76 but in dado / skirting or on vertical surfaces, laid over and including 10 mm thick backing coat in cement mortar 1:4 .

M&L for factory made vitrified paver tiles , 300mm x 300mm x (9 - 10)mm thick , as approved by GE as in floors , laid over and including screed bed 15mm thick in cement mortar 1:4 set, jointed and pointed in neat cement slurry all as specified and as directed.

M&L for 60mm thick, factory made, chamfered edge, cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, lawns, drive ways or light traffic, parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; etc complete all as specified and as directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick masonary surfaces or concrete surfaces, finished even and fair without using extra cement complete all as specified and as directed.

M&L for 10 mm thick rendering in cement mortar 1:6 on other than fair faces of brick masonry surfaces or concrete surface, finished even and smooth with sagol complete all as specified and as directed.

M&L for 5 mm thick rendering in cement mortar 1:3 on fair faces of brick or concrete surface, finished even and smooth with sagol as in ceilings, complete all as specified and as directed.

M&L for raised pointing in cement mortar 1:3 to random or polygonal rubble, uncoursed or brought upto courses masonry including taking down existing pointing complete all as specified and as directed.

S&F GI wire netting 0.90 mm dia and 12mm mesh, in walls, celling, beams etc including all laps cutting and waste, including making V groove in crack portion and filled with cement mortar 1:2 etc complete. all as specified and as directed.

M&L for preparation of new plastered or unplastered surface of walls and applying three coats of white wash complete all as specified and as directed.

M & L for preparation of newly plastered or unplastered surface of ceiling and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of new surfaces applying two coats of oil bound distemper on wall surfaces using roller all as specified and as directed.

M&L for preparation of new plastered wall surfaces, and applying minimum 1mm thick wall care putty over prepared wall surface including sanding of the putty surface after drying to achieve even and smooth finish and applying two coat of oil bound distemper over and including a coat of primer complete all as specified and directed.

M&L for complete removal of existing wall surfaces, and applying minimum 1mm thick wall care putty over prepared wall surface including sanding of the putty surface after drying to achieve even and smooth finish to receive final finish complete all as specified and directed.

M&L for applying two coats of oil bound distemper on wall surfaces using roller newly prepared wall surfaces all as specified and as directed.

M&L for preparation of new plastered surfaces or previously untreated surface of wall and applying two coats of cement base paint over one coat of primer all as specified and as directed.

Hacking out of old broken glass (any thickness ,size quality or description) from wooden / metal frames including punching or drilling out old glazing pins/spring clips complete all as specified and as directed.

S&F 3 mm thick frosted/figured glass, pin headed type and glazing with oil putty in square n exc 0.5 Sqm in each pane to steel windows including glazing pins etc. complete all as specified and as directed.

S&F 3 mm thick plain sheet glass and glazing with oil putty in square n exc 0.5 Sqm in each pane to steel windows including glazing pins etc. complete all as specified and as directed.

M&L for preparation of new wood or wood based surface of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paints over one coat of pink primer complete all as specified and as directed.

M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paints over one coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L for 15 mm bore GI tubing medium grade with all fitting and fixed complete on walls and ceilings or laid in floors etc complete all as specified and as directed.

S&F for 16mm outer diameter CPVC pipes SDR11 & Plain CPVC SDR fittings in trenches and wall complete all as specified and as directed

Fixing only old serviceable GI tubing 15 mm bore, with and including new fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed.

M&L for 20 mm bore GI tubing medium grade with all fitting and fixed complete on walls and ceilings or laid in floors etc complete all as specified and as directed.

S&F for 20mm outer diameter CPVC pipes SDR11 & Plain CPVC SDR with and including new fittings in trenches and wall complete all as specified and as directed

Fixing only old serviceable GI tubing 20 mm bore, with and including all new fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed.

M&L for 25 mm bore GI tubing medium grade with and including all new fittings and fixed complete on walls and ceilings or laid in floors etc complete all as specified and as directed.

Fixing only old serviceable GI tubing 25 mm bore, with and including new fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed.

S&F in repairs, rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), 500 litres capacity, tripple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting all as specified and as directed.

All as per item No. 105 above but 1000 litre capacity with 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball

All as per item No. 105 above but 2000 ltr capacity with 25 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball

All as per item No. 105 above but 5000 ltr capacity with 25 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball

Disconnecting existing PVC tanks, exc 250 and not exc 500 Ltrs capacity, setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and refixing in position including cleaning and removing all scales and dirt etc from mouths of circulating pipe etc. complete all as specified and as directed.

All as per item No. 109 above but PVC tanks of capacity exc 500 ltrs and not exceeding 1000 ltrs .

S&F in repairs, PVC cover/lid for rotational mounded polythene water storage tanks any capacity including fixing with necessary device complete all as specified and as directed.

S&F in repairs, bib tap, 15mm dia cast copper alloy chromium plated, with crutch or butter- fly handles screwed down for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repairs, 15 mm bore pillar taps, cast copper alloy with capstan heads, fancy type, chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed.

S&F in repairs, brass crominium plated wash basin mixer for mixing hot and cold water for Wash hand basin screwed down for iron pipe 15 mm bore and fixed complete all as specified and as directed.

S&F in repairs, brass crominium plated mixer for mixing hot and cold water for kitchen sink screwed down for iron pipe 15 mm bore and fixed complete all as specified and as directed.

S&F in repairs, brass crominium plated wall mixer for mixing hot and cold water and bend for connecting to shower, screwed down for iron pipe 15 mm bore and fixed complete all as specified and as directed.

S&F in repairs spindle of wall mixer, sink mixer & basin mixer fixed complete all as specified and as directed.

S&F in repairs, stop valves/ angular stop valve, 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.

S&F in repairs, 20 mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all as specified and as directed.

S&F in repairs, ball valves high pressure PTMT with epoxy coated aluminium rod & high density plastic ball screwed for 15 mm bore iron pipe (Minium weight 142 gms), complete all as specified and directed.

S&F in repairs, ball valves high pressure PTMT with epoxy coated aluminium rod & high density plastic ball screwed for 20 mm bore iron pipe (Minium weight 210 gms), complete all as specified and directed.

M&L in repairs for grating doom 100mm dia PTMT all as specified and as directed.

S&F in repairs, 32/ 40 mm bore PVC flexible outlet pipes for wash basin/ sink/ urinal fixed complete all as specified and as directed.

S&F in repairs, PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

S&F in repairs, PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed.

S&F in repairs, 110 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F in repairs, 75 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F in repairs, 110 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to wall all as specified and as directed.

S&F in repairs, 75 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints,fixed to wall all as specified and as directed.

S&F in repairs, 110 mm dia PVC (SWR) bends of any radius complete all as specified and as directed

S&F in repairs, 110 mm dia PVC (SWR) bends with access door, of any radius, complete all as specified and as directed

S&F in repairs, 75 mm dia PVC (SWR) bends of any radius complete all as specified and as directed

S&F in repairs, 75 mm dia PVC (SWR) bends with access door, of any radius complete all as specified and as directed

S&F in repairs, PVC (SWR) branch piece of 110 mm bore , provided with access door, double (double Y) equal or unequal, all as specified and as directed

S&F in repairs, PVC (SWR) branch piece of 75 mm bore ,provided with access door, double (double Y) equal or unequal, all as specified and as directed

S&F in repairs, PVC (SWR) junction of 110 mm bore single, (single T) equal or unequal with access door, all as specified and as directed

S&F in repairs, PVC (SWR) junction of 75 mm bore single, (single T) equal or unequal with access door, all as specified and as directed

S&F in repairs, PVC (SWR) 110 mm bore vent cowl, all as specified and as directed

S&F in repairs, PVC (SWR) 75 mm bore vent cowl, all as specified and as directed

M&L in repairs, for PVC (SWR) floor trap, plain with grating including jointing with solvent cement to waste pipe fixed in cement concrete type (1:2:4) type B1all as specified and as directed.

S&F in repairs, CP health faucet (hand shower) with 8 mm dia, 1200 mm long flexible tube, wall mounted / hooked all as specified and as directed.

S&F in repairs, chromium plated shower rose with or without swivel joints, 125mm size, , including fixing to steel pipe or union etc complete all as specified and as directed.

S&F in repairs, vitreous China, white, squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest, set in cement concrete including flush pipe and connecting to trap / flushing cistren and making good to floor complete all as specified and as directed.

S&F in repairs, vitreous china wash down water closet ( pedestal pattern) including connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap set and including white or black seat cover for pedestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws etc complete all as specified and as directed.

S&F in repairs, 10 Litres capacity PVC valveless syphonic action type, flushing cistern, low level, white or coloured, with inlet, ball valve, float and handle including brackets etc complete all as specified and as directed.

S&F in repairs, vitreous china wash hand basin, white flat back size 550 mm x 400 mm including brackets including pillar tap, 15 mm bore chromium plated, fancy type, cast copper alloy with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts and PVC waste pipe,15mm dia PVC connection pipe complete all as specified and as directed.

S&F in repairs, stainless steel sink with drain board made of 1mm thick sheet for kitchen including plugs, washers, waste pippe, cast iron cantilever brackets, connecting union to pipe, over all size 915 mmx 460 mm with bowl size 410 mm x 330 mmx 160 mm all as specified and as directed.

S&F in repairs, stainless steel sink made of 1mm thick sheet for kitchen including plugs, washers, waste pipe, cast iron cantilever brackets, connecting union to pipe, over all size 495 mmx 420 mm with bowl size 410 mm x 330 mmx 160 mm all as specified and as directed.

M&L in repairs, for vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe) including urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms), PVC connection, 40mm PVC waste pipe & 40 mm waste coupling providing and fixing plugs, bedding urinal against wall in mortar 1:2, securing urinal to plug, with and including 60mm long screws, pointing around urinal back in cement, fixing flush pipe, complete all as specified and as directed.

M/s Mauli Construction

DHANANJAY BABAN KALANE

Poojan Infra and Developers

M/s Meher Construction

OM SAI ASSOCIATES

M/S. Z.K.ENTERPRISES, AHMEDNAGAR

AMAR CONSTRUCTION