Please See item 01 of Enit

Amount

Earth work in excavation in foundation of trenches/bulk Excavation in all kinds of soil with required depth including removal of excavated soil/slush etc. ,dressing of bed and sides ,dewatering (if any) of trenches till construction upto ground level is achieved and disposal of excavated soil as directed by the Engineer in charge including all leads, lifts and Carriage by mechanical means as required complete.

Providing and laying stone soling tightly hand packed under foundations, footings ,floors etc. including carriages of materials from source to site of work complete in all respects.

Providing & laying in position cement concrete of specified grade excluding the cost of centering and shuttering all works upto plinth level.

(a)1:4:8( 1 cement: 4 coarse sand: 8 graded stone agg/ 40mm nominal size) crushed aggregate)

(b)1:3:6( 1 cement: 3 coarse sand: 6 graded stone agg/ 20mm nominal size) crushed aggregate) for mass concrete works.

Providing and laying in position specified grade 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20mm nominal size crushed aggregate) for reinforced cement concrete works excluding the cost of centering, shuttering, finishing and reinforcement.( All work at all levels.)

Reinforcement for R. C. C. work including straightening, cutting, bending, placing in position and binding all complete. Hot Rolled Deformed Bars.( All work at all levels complete.)

Structural steel work in welded in built up sections trusses and framed work, including cutting, hoisting, fixing in position and applying of priming coat of approved steel primer complete in all respects..(All work at all levels complete.)

Providing and fixing M.S Round holding down bolts for trusses, 300 mm to 450 mm in length and 16 mm dia including nuts, washers , Plates and threading etc. complete.( All work at all levels complete.)

Providing form work including Centering, shuttering, strutting, propping etc., using ply wood sheeting with water proofing ply board (12 mm min.thickness) and removal of the same for( All work at all levels complete.).-

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. Layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m.

Supplying, filling with river sand mixed with boulders in 20 Cm layers including watering, compacting & dressing under flooring in ground floor

Providing and laying Solid Concrete Blocks of 1:3:6 mix(1 cement : 3 coarse :6 stone aggeragte 20 mm nominal size ) in cement mortar of 1:6 (1 cement : 6 Coarse sand ) upto Floor 5 level including carriages of materials from source to site of work complete in all respects.

Providing wood work in frames of doors, windows, clerestory windows and other frames Wrought framed and fixed in positions ( Ist class kashmiri kail wood)

Providing and fixing 35mm thick paneled or paneling and glazed shutters for windows and clerestory windows including I.S.I. Marked black enameled M.S. butt hinges with necessary screws excluding paneling, (which will be paid separately) ( Ist class kashmiri kail wood)

Providing and fixing 35mm thick panelled doors, including I.S.I. Marked black enameled M.S. butt hinges with necessary screws including Ornamental Kail wood panels (20 mm avg. thick) ( Ist class kashmiri kail wood) as required complete as per the directions of Engineer Incharge

Providing and fixing paneling or paneling/ glazing in paneled or paneled & glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion in side grooves or rebates to be measured). Paneling for paneled or paneled glazed shutters .

Providing 4 mm thick panels of plain glass for glazing shutters (only panel area to be measured) including cost of teak wood beadings of required size complete.

Providing and fixing 5mm thick panels of plain glass for fixed glazing panels/ shutters (only panel area to be measured) including cost of teak wood beadings of Traingular Shape 10 mmx10 mm/2 size complete.

Providing and fixing 40x5mm flat iron hold fasts 40cms long including fixing to frame with 10mm dia bolts, nuts and wooden plugs and embedding in cement conc. blocks 30x10x15 cms 1:3:6 ( 1 cement: 3 coarse sand : 6 graded stone agg. 20mm nominal size).

Providing and fixing 30mm thick wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm with wire of dia .0.63 mm for doors, windows and clerestory windows including I.S.I. marked black enameled M.S. butt hinges with necessary screws ( class kail wood.)

Providing and fixing aluminium work for doors, windows,ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber I neoprene .gasket felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I panelling, C.P.brass I stainless steel screws, all complete as perarchitectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.)

For fixed portion Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

For shutters of doors, windows &ventilators including providing and fixing hinges , pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber I neoprene gasket required (Fittings shall be paid for separately.) Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing 12mm thick prelaminated particle boardflat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-l type-11) in panelling fixed in aluminium doors, windows shutters and partition frames with C. P. brass I stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing glazing in aluminum door,window,ventilator shutters and partitions etc. With EPDM rubber /neoprene gasket etc. Complete as per the architectural drawings and the directions of engineer-in-charge (Cost of aluminium snap beading shall be paid in basic item).With float glass panes of 8mm thickness (weight not less than 20 kg/ sqm)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, having brand logo embossed on the body/plate with double spring mechanism and door weight upto 125 kg for doors including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot"and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge With Stainless Steel cover plate minimum 1.25 mm thickness.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement@ 0.488 kg/sqm mixed "Ywith with water proofing cement compound @ 0.253kg/sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound@ 0.126 kg/sqm . This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes prepartation of surface, treatment and sealing of all joints,corners, junctions of pipes and masonary with polymer mixed slurry.

Providing and fixing of specially designed wooden Shinshak-ornamental ladakhi type, wrought framed, jointed and fixed in position complete with architectural features like lining, bands, moldings, caps etc. as required with two coats of special primer all complete as per the directions of Engineer Incharge including painting specially designed wooden shinshak with deluxe multi surface paint of required shade two or more coats applied @ 0.90 lit/10sq.m over an under coat of primer applied @ 0.75 lit/ 10sq.m of approved brand and manufacture all complete as per the directions of Engineer Incharge.. (a). length of shinshak up to 12’-0’’

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Size of tile 60x60cm including all lifts,leads,carriage of the material complete as per specification and as directed by Engineer in Charge

Providing and fixing ( gang saw cut mirror polished (pre-moulded and pre-polished), machine cut for flooring, steps ,risers of stairs etc of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding (of edges wherever required ) and polishing to edge to give high gloss finish etc. complete at all levels. Granite of any colour and shape 20 mm thick. and slab area over 0.50 sq m. (Note: The Granite stone slab shall be cut to required size and laid to the required pattern including rounding, chamfering, bull nosing of the edges as directed. Actual area of slab, as laid shall be measured) Sample to be approved by Engineer-in-charge. (including cost of all material, leads, lifts and carriages etc upto site of work complete

Providing and fixing mirror polished machine cut marble for flooring, steps ,risers of stairs etc of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding (of edges wherever required ) and polishing to edge to give high gloss finish etc. complete at all levels. Granite of any colour and shape18 mm thick. and slab area over 0.50 sq m. (Note: The marble stone slab shall be cut to required size and laid to the required pattern including rounding, chamfering, bull nosing of the edges as directed. Actual area of slab, as laid shall be measured) Sample to be approved by Engineer-in-charge. (including cost of all material, leads, lifts and carriages etc upto site of work complete

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Providing and fixing planned eaves boarding of Ist class kail wood (250 x 32 mm ) N/S with necessary grooves and chamfer as per detailed drawing.(ornamental

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) 0.50mm+/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in 240 mpa steel grade 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5 x 55mm) with EPDM seal or with polymer coated J or L hooks,bolts and nuts 8mm diameter with bitumen and G.l. limpet washers or with G.l. limpet washers filled with white lead complete upto any pitch in horizontal /vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required including all lifts,leads and carriages complete job

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+/- 5 %) total coated thickness(TCT), Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated Jor L hooks, bolts and nuts and GI:Seam bolts, and nuts,GI plain and bitumen washers complete: Ridges plain (500- 600mm)

Providing valleys of 90cm wide overall in plains G.S. sheets fixed with polymer coated J. or L. hooks, bolts and nuts 8 mm dia G I. limpet and bitumen washers complete.1.60mm thick with zinc coating not less than 350gm/m2

Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand:4 graded stone agg.) finished with a floating coat of neat cement including cement slurry but excl. the cost of nosing of steps etc. complete. (50mm thick with 20mm nominal size crushed stone aggregate)

Cement plaster skirting (up to 30cms height) with cement mortar 1:3 (1cement:3 coarse sand mortar) finished with a floating coat of neat cement. (18mm thick).

Providing & fixing glass strips in joints of terrazzo/cement conc. floating (40mm wide and 4mm thick).

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubeschannels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete,i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such Kilogram as nuts, bolts, fasteners etc. including lifts, carriage of the material complete job

Extra for Providing & fixing of stainless steel navel post (Ornamental ) including top ball of 304 grade of required height duly anchored to floor with dash fasteners Complete as per the directions of Engineer in charge.

15 mm thick cement plaster on rough side of single or half brick wall in (1 cement: 6 fine sand mix).

10 mm thick cement plaster on ceilings, soffits etc in (1 cement: 4 fine sand mix).

Providing and applying cement based wall putty of required thickness over plastered surface to prepare the surface even and smooth complete in specified areas as per specified patter. (Birla make)

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Painting on Walls /Ceilings with plastic emulsion paint of approved brand and manufacture to give an even shade (Two or More Coats) including all necessary scaffolding etc. (Including cost of all material, leads, lifts and carriages etc upto site of work complete).

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 litre/10 sqm over and including base coat of water proofing cement paint applied@ 2.20kg/10 sqm)

Applying priming coat with ready mixed pink or grey primer of approved brand and manufacture on wood work complete.

Painting with synthetic enamel paint of approved brand and manufacture of required shade and colour to give smooth finish with two or more coats on new wood and based surfaces

Making plinth protection 50mm thick of cement conc. 1:3:6 (1 cement : : 3 coarse sand : 6 graded stone agg 20mm nominal size) over 75mm bed of dry stone agg. 40mm nominal size well rammed and consolidation and grouted with fine sand incl. finishing the top smooth..

Providing and fixing hardware fittings of approved brand and of required type as approved by Engineer Incharge/ consultant. (Aluminum Fittings of Antique Finish) complete as per the specifications

a) Tower bolts 200mm

b) Tower bolts 100mm

(b)Sliding door bolts/AL drops (300 mm )

c) Handles

Soil investigation by conducting bore holes 250mm dia 10 mt. deep by SPT/plate load and related tests, soil properties to be elevated complete. Conducting tests and preparing soil test/bearing capacity report and recommending Structural Engineer the complete soil characteristics, so as to enable the Structural Engineer to design building structure

M/S MOHAMMAD AYOUB RATHER

M.N.Enterprises

M/s Shalimar Constructions