ADDITION AND ALTERATION OF OLD WINDOWS REPLACE WITH ALUMINIUM WINDOWS, REPAIRS TO WALL INCL REWIRING OF BLDG NO P-406 AND ADDN AND ALTN OF ALUMINIUM WINDOWS AND RENEWAL OF INTERNAL WIRING OF BLDG NO P-541 AT NAVAL STATION KARANJA

Amount

Taking down chowkats or frames exc 1.5 sqm but not exc 4 sqm each with shutters (without taking off shutters from the frames) complete all as specified and as directed by Engr-in-charge.

Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from the frames) complete all as specified and as directed by Engr-in-charge.

Material and labour for 16-18mm thick granite work of any type (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in CM 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite over 20mm thick screed in CM 1:4 complete all as specified and as directed by Engr-in-charge.

Material and labour for providing and fixing including fabrication of powder coated aluminium (minimum thickness of powder coating 50 microns) work for doors, windows, ventilators and partitions (fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc., aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, CP brass/ stainless steel screws complete all as specified and as directed by Engr-in-charge.

Material and labour for providing and fixing powder coated aluminium (minimum thickness of powder coating 50 microns) for shutters of doors, windows and ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket, star lock etc., aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, CP brass/ stainless steel screws complete all as specified and as directed by Engr-in-charge.

Supply and fix for sheet glass 4mm thick, ordinary quality and glazing with oil putty in square complete all as specified and as directed by Engr-in-charge.

Supply and fix for frosted glass 4mm thick, pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane complete all as specified and as directed by Engr-in-charge.

Supply and fix for aluminium louvers with levers and locking arrangement suitable for fixing 100mm wide 4 to 6 Nos glass complete all as specified and as directed by Engr-in-charge.

Supply and fix for aluminium anodised grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC15) of approved design /pattern (DG 104), with approved standard section and fixed to existing window frame with CP brass /stainless steel screws not less than 50mm and @ 200mm c/c, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section 28x19x2mm around the opening complete all as specified and as directed by Engr-in-charge.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc., including racking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and as directed by Engr-in-charge.

Material and labour for 20mm thick polymer modified ready mix cement based plaster on internal surfaces complete all as specified and as directed by Engr-in-charge.

Supply only integral water proofing compound complete all as specified and as directed by Engr-in-charge.

Material and labour for 8mm thick polymer modified ready mix cement based plaster on internal surfaces complete all as specified and as directed by Engr-in-charge.

Material and labour for providing and laying of 2mm thick wall care putty on walls complete all as specified and as directed by Engr-in-charge.

Material and labour for preparation of new surfaces of walls and applying two coats of oil bound distemper (oil emulsion) on walls over a coat of alkali resistant primer complete all as specified and as directed by Engr-in-charge.

Material and labour for new or old surfaces of exterior wall decorating and water proofing treatment to wall surface by wire brushing in order to remove dust, dirt, loose particles, laitance. Thereafter wash the surface with clan water and allow to dry. Fill visible cracks/ joints by chemistic crack seal caulking compound and allow to dry for 24 hours. Apply a primer coat of chemistic prime M Seal (water base primer) and allow to dry for 6 hours. Thereafter apply 2 coats of chemistik PDS-50 (WB high build anti caronatin coating cum waterproofing) and shade by brush at the interval of 8 hours between the coat and allow to dry to match the existing shade including necessary scaffolding for any height, covering etc., complete all as specified and as directed by Engr-in-charge.

Material and labour for silicon gun paste around windows of any type at any height of the building by using scaffolding complete all as specified and as directed by Engr-in-charge.

Supply and fix for aluminium anodised curtain rod 25mm dia fixed between brackets complete all as specified and as directed by Engr-in-charge.

Supply and fix for aluminium anodised brackets for 25mm dia curtain rod complete all as specified and as directed by Engr-in-charge.

Material and labour for cutting openings, through brick walls for door, window and other openings or enlarging existing openings. converting window into door defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc., to store and rubbish not exc 50m built in cement morter including making good to existing surfaces complete all as specified and as directed by Engr-in-charge.complete all as specified and as directed by Engr-in-charge.

Supply and fix for 25mm dia mild steel chromium plated curtain rod fixed with bracket both end and knob, hooks etc., complete all as specified and as directed by Engr-in-charge.

Taking down carefully copper/ aluminium point wiring (light, fan socket or power) through steel/ PVC conduit/ casing caping including complete fittings such as switches, ceiling roses, pendants, regulators, sockets, buzzer, bell, switch sockets, etc., removing and making good to the disturbed surfaces of walls /ceiling etc., with its original specification complete all as specified and as directed by Engr-in-charge.

Material and labour for point wiring with single core 1100 volts grade 1.5 sqmm size PVC FRLS insulated unsheathed stranded copper conductor cable using colour code drawn through conceiled PVC conduit with in and including all modular accessories like metal flush box, cover plate with frame plates of suitable sizes and including 1.5 sqmm PVC insulated unsheathed copper conductor cable for continous earth conductor (using green colour) to common earth and connecting to earth dolly for the following complete all as specified and as directed by Engr-in-charge. Note: The rates includes for neccessary wall cutting and chasing. One light /fan /call bell point controlled by one switch.

One 5 pin socket outlet 5 Amps on independent board.

One 5 pin socket outlet 5 Amps on same board.

One light point controlled by 2 way switch SP 5 Amps, 240 Volts.

All as per item No.23 here-in-before but with 2.5 sqmm multi stranded copper conductor 1100 volts grade FRLS PVC insulated sheathed cable with FRLS PVC 2.5 sqmm multi standard insulated unsheathed copper wire for continuous earth on independent board.

All as per item No.23 here-in-before but with 4 sqmm multi stranded copper conductor 1100 volts grade FRLS PVC insulated sheathed cable with FRLS PVC 4 sqmm multistandard insulated unsheathed copper wire for continuous earth on independent board.

Supply and fix for switch modular single pole one way, 6 Amps (ISI marked) complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular switch flush button, single pole two way, 6 Amps (ISI marked) complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular bell push flush type 6 Amps (ISI marked) complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular socket outlet 15 Amps, 5-in-1, controlled by one switch (ISI marked) complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular socket 2 in 1, 3 pin, 6 Amps flush type (ISI marked) complete all as specified and as directed by Engr-in-charge.

Supply and fix for switch modular single pole one way, 16 Amps (ISI marked) complete all as specified and as directed by Engr-in-charge.

Supply and fix for ceiling rose PVC /polycarbonate, isolated body surface bakelite 65mm dia three terminals complete all as specified and as directed by Engr-in-charge.

Supply and fix for ding dong door bell electric suitable for AC 230 volt, single pole complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular type fan 5 step regulator for ceiling fan complete all as specified and as directed by Engr-in-charge.

Supply and fix for LED batten with 20W LED tube light in wall /surface connecting with all required accessories like PVC box base, flexible cable from ceiling rose etc., surface and wall mounted LED batten, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver and including LED tube rod complete all as specified and as directed by Engr-in-charge.

Supply and fix for LED batten with LED tube light 10W 2 feet in wall /surface connecting with all required accessories like flexible cable from ceiling rose etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix for double door MCB DB made out of 18SWG CRCA steel sheets, phosphates powder coated with copper bus bar, earth stud, din rail, polyamide terminal blocks for incoming and outgoing circuits, inbuilt loose wire box, ground terminal blocks, duly prewired with thimble flame retardant copper conductors and poly layer for protection SP 240 volts 200 Amps rated bus bar 2+6 way double door openable, including taking out old unserviceable MCB DB any size /type complete all as specified and as directed by Engr-in-charge.

Supply and fix for replacement MCB distribution board VTPN, 6 ways, 415 Volts, 50 Hz, AC, double door made out of sheet metal phosphatised and painted with epoxy polyster based powder paints with 200 Amps rated bus bar and earth bar, ISI marked complete all as specified and as directed by Engr-in-charge.

Supply and fix for 6 to 32A MCB single pole 240 V, 10 KA (C-Series) complete all as specified and as directed by Engr-in-charge.

Supply and fix for MCB double pole RCBO 240 volts AC 40 Amps (C-series) of 100 MA complete all as specified and as directed by Engr-in-charge.

Supply and fix for MCCB 4 pole 100A, 415 volts, 16 kA complete all as specified and as directed by Engr-in-charge.

Taking down exhaust fan and keeping in safe custody for reuse and refixing the same after duly painted and marking of MES number on fan with connected accessories complete all as specified and as directed by Engr-in-charge.

Fixing only exhaust fan single phase 250mm sweep including all connected accessories and making necessary cutting and chasing to make holes on wall to fix the fans or existing place complete all as specified and as directed by Engr-in-charge.

Supply and fix for exhaust fan single phase 250mm sweep including all connected accessories and making necessary cutting and chasing to make holes on wall to fix the exhaust fans complete all as specified and as directed by Engr-in-charge.

Taking down ceiling fan and keeping in safe custody for reuse and refixing the same after duly painted and marking of MES number on ceiling fan of size 1200mm sweep with connected accessories complete all as specified and as directed by Engr-in-charge.

Taking down geyser and keeping in safe custody for reuse and refixing the same after duly painted and marking of MES number on geyser 25 ltrs including all connected accessories like pvc connection hot/ cold water etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix for LED building security light fitting with 40mm dia light grade pole bracket /angle to fit security light of 45W IP 66 protection complete all as specified and as directed by Engr-in-charge.

Supply and fix for LED decorative wall mounting chrome finish fixture with textured glass with 5W LED lamp complete all as specified and as directed by Engr-in-charge.

Supply and fix for sheet metal enclosure with socket plug top and 20 Amps single pole MCB complete all as specified and as directed by Engr-in-charge.

Supply and fixing, jointing, connecting and testing in trenches XLPE/ PVC insulated PVC sheathed cable of size 4 core 25 sqmm heavy duty 1100 volts grade, aluminum conductor in trenches/ ducts, including taking out cable cover and cable complete all as specified and as directed by Engr-in-charge.

Excavation in trenches for not exc 1.5m wide and not exc 1.5m depth and getting out in soft/ loose soil including taking out faulty cable/ cable covers and GI pipe complete all as specified and as directed by Engr-in-charge.

Returning filling in including spreading levelling watering and well ramming in layers not exc 25cms complete all as specified and as directed by Engr-in-charge.

Removing excavated material not exc 50m and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and as directed by Engr-in-charge.

Material and labour for sand cushioning for protection of UG cable including punning of sand in layers complete all as specified and as directed by Engr-in-charge. Note: Only punned thickness shall be measured for payment.

Supply and laying unreinforced precast concrete cable cover class LV type 1, flat size of 250x150x40mm complete all as specified and as directed by Engr-in-charge.

Material and labour for GI pipe light grade of 40mm dia with all fittings laid in trenches complete all as specified and as directed by Engr-in-charge.

Material and labour for earthing complete with galvanised steel earth plate electrode of size 600x600x6mm thick burried directly in ground vertically in a pit of depth not less than 2.25m below ground levels with top edge of the earth plate not less than 1.5m below normal ground level surrounded from all sides by mixture of charcoal and common salt and electrode connected to and including galvanised earth lead wire 4mm dia means of bolts, nuts, check nuts and washers of galvanised steel and GI pipe light grade 20mm dia bore for watering funnel with wire mesh. CI cover with frame, PCC chamber pit with PCC 1:3:6 type C-2 excavation and earth work all as shown in electrical plate No. 5 connected to earthing test point including testing on completion complete all as specified and as directed by Engr-in-charge. Note: The unit rate includes for protection pipe and GI strip dia from top of earth plate upto 5m above ground level.

pk Enterprises

Mahadev Enterprises

BALAJI TRADERS

M/s Jeet Construction

Srishti Construction