Signalling works in connection with provision of pedestrian subways in Solapur division of central Railway.

02-SOR EXECUTION

03-NS SUPPLY AND EXECUTION

Item Breakup - 01-SOR SUPPLY

Sealed maintenance free VRLA Battery/Cell Numbers 2 Volt, 300AH IRS : S-93/96 (A) (Amd.1) or latest.(Inspection by RDSO) SOLAPUR DIVISION-S AND T/CENTRAL RLY

Supply of Battery Charger self regulating Numbers floor mounting type with 230 V AC single phase input and output 24V DC, 20A as per spec. IRS.S.86/2000 (Amd.4) with latest amendments for Axle counter applications . (Inspection by RDSO)

Supply of Battery Charger self regulating Numbers floor mounting type with 230 V AC single phase input and output 24V DC, 30A as per spec. IRS.S.86/2000 (Amd.4) with latest amendments for Axle counter applications . (Inspection by RDSO)

Supply of 63 A rating, 4 pole changeover Numbers switch disconnector with dual shaft position & staggered terminals with sheet steel enclosure and extended handle of Siemens/ L&T/ HAVELLS/ LEGRAND make.(Inspection by consignee)

Supply of Shunt Signal Group Siemens Numbers make [No. A-RT-RG-A065] or functional equivalent without base plates (suitable for LED Signal).(Inspection by RDSO)

Supply of Point Group PI, Siemens make Numbers (No.RSSK 31/0001) or functional equivalent without base plates.(Inspection by RDSO)

Supply of Plug In type Relay Metal to Metal Numbers t y p e neutral relay mini groups (Non AC Immunised) Siemens make (No. RSSK 30/0011) (Ref. IRS:S46 with Amdt. 1 & firms specification IRS S 23-88 : IRS S 34-68 ( Or latest ) or functional equivalent without base plates. Contact configuration 5F/3B or 6F/2B or 4F/4B to be specified by Engineer incharge. (Inspection by RDSO)

Supply of QN1 Non AC immunised neutral Numbers relay, 8F-8B, 24 VDC along with plug board, retaining clip and connectors confirming to BRS:930, , IRS:S34 ; IRS: S23 (Or latest) (Inspection by RDSO)

Supply of QN1 Non AC immunised neutral Numbers relay, 12F-4B, 24 VDC along with plug board, retaining clip and connectors confirming to BRS:930, , IRS:S34 ; IRS: S23 (Or latest) .(Inspection by RDSO)

Supply of Hand Cuff Locks/ Godrej Navtal Numbers lock with Three common keys.(Inspection by Consignee)

Supply of ARA Terminal blocks with links Numbers made of PBT Specn No.IRS:S-75/2006 (Rev - 2) with latest amendments and RDSO Drg.No.SA-23741A Alt.4, SA-23745 Alt.5, SA-23746, SA-23748 Alt.4 & SA-23756A Alt.3.(Inspection by RDSO)

Supply of cartridge fuse block made of PBT Numbers as per RDSO Drg No SA-23748 Alt 4, SA- 23749 & Spec NoIRS:S-75/2006 (Rev - 2) with latest amendment. Fuse block shall be suitable for round head type voltage fuses. (Inspection by RDSO)

Supply of round head type non detoriating Numbers type low voltage cartridge fuse as per Spec N o IRS:S-78/92 with latest amendments 2A/4A/6A capacity .(Inspection by RDSO)

Supply of Tik-tak, piano type switches,5A Numbers (as per IS Specification).(Inspection by Consignee) SOLAPUR DIVISION-S AND T/CENTRAL RLY

Supply of three pole plug and socket 5 Amp Numbers (as per IS Specification).(Inspection by Consignee)

Supply of Lamp 110V/24W, 2 Pin for Loc. Numbers (Inspection by Consignee)

Supply of Apparatus Case with godown Numbers locks with detachable handle on both the doors. Single Case as per Drg. No.SK 783-1 & 2 with latest alteration.(Inspection by RITES)

Supply of Apparatus Case with godown Numbers locks with detachable handle on both the doors. Half Case as per Drg. No.SK 783-1 & 2 with latest alteration.(Inspection by RITES)

Supply of earth electrode assembly as per Numbers Drg.No. CR/S&T/SK-815 (Inspection by Consignee)

Maintenance RDSO/SPN/197 , Ver . 1.0 (or latest) consisting of : 1) Copper bond steel electrode 3 Mtr long 17mm dia with copper bonding thickness of min. 250 micron & UL listed & marked-01 No. 2) Earth enhancement compound RDSO Approved in sealed bag of 10 Kgs - 03 No. 3) Copper strip 150 x 25 x 6mm - 02 No. 4) Copper strip 300 x 25 x 6mm - 01 No. 5) 35 Sqmm Copper Cable to connect earth electrode to MEEB - 15 Mtr Approx.(Inspection by RDSO)

Supply of GI pipe, inner dia. 100mm dia. B- Metre class as per spec. No.IS 1239 PT. 1/2004 or l a t e s t with sockets and fittings. TATA/JINDAL/ZENITH BIRLA make. (Inspection by Consignee)

Supply of DWC HDPE pipe with one snap fit Metre coupler and 'O' ring fire resistant, anti rodent, in 6 meter length of size 120 mm outer dia as per RDSO/SPN/204/2011 Ver. 1.1 with Amd.1 or latest.(Inspection by Consignee)

Supply of RCC pipes half round of size Numbers 150mm dia outer and 100 mm dia internal 1 mtr long matching to IS No. 458/2003 amendment-1 with Rev.4 As per Drg No.DRM(S&T) SUR/06/2023/A.(Inspection by RITES)

Supply of RCC pipes half round of size Numbers 300mm dia outer and 250 mm dia internal 1 mtr long matching to IS No. 458/2003 amendment-1 with Rev.4.As per Drg No.DRM(S&T) SUR/07/2023/A (Inspection by RITES)

Supply of Modular terminal block of 2.5 Numbers sq.mm 2 in 2 out type disconnect type terminal along with as per RDSO SPN/189/2004 Ver. 3.0. ( Or latest). The current capacity of 16 Amps and more. The terminal should have marking at centre to view description from front. Material to be procured from RDSO approved firms only. (Inspection by RDSO)

Supply of DIN Channel for the terminals 1 Numbers Mtrs each.(Inspection by Consignee)

Supply of End plates for modular terminal Numbers block.(Inspection by Consignee)

Supply of End Clamp for modular terminal Numbers block.(Inspection by Consignee) SOLAPUR DIVISION-S AND T/CENTRAL RLY Total 17447393.39

Item Breakup - 02-SOR EXECUTION

Wiring and charging of Integrated Power Lot Supply System to signaling installation. This includes connection of MF Earth of 1 ohm earth resistance for IPS and power distribution connection to bus bars and relay racks in the room with contractor's own wiring materials and fabrication and fixing of AC/DC power distribution board made on 10mm thick Phenolic hylam sheets or any standard make with connections suitable for 63 A.Wiring to be done considering site requirement , depending upon the load with suitable wires,lugs & glands as per instructions of Engineer-in-charge. The item also includes supply & fixing of ladder along the wall for carrying power supply wires/cables from IPS room to Relay room/power room and potential free contact wiring at Datalogger IDF, etc.

Excavation and Casting of Main signal Numbers foundation as per Drg No SK 801 with contractor's own materials including cement and anchor bolts of standard size. The required scaffolding Ferma etc for Casting of foundation will have to be brought by the contractor at his own cost.

Fabrication laminated/Fibre glass sheet in location box by providing all fixtures as per Railway Drawing including fixing of PVC coated/with PVC pipe covered string rods at the back side for cable support with contractor's own materials. The work shall be done as per drg and arrangement similar to SK 783-1&2. with latest alterations & as per instructions of Rly engineer at site. Single Case

Fabrication laminated/Fibre glass sheet in location box by providing all fixtures as per Railway Drawing including fixing of PVC coated/with PVC pipe covered string rods at the back side for cable support with contractor's own materials. The work shall be done as per drg and arrangement similar to SK 783-1&2. with latest alterations & as per instructions of Rly engineer at site. Half Case

Fixing of ARA Terminals and fuse blocks on Numbers 12560.00 phenolic laminated sheets and fixing by stainless steel/brass nuts & bolts.This includes provision of two additional holes on the board on either side for cable conductor entry.

Termination of cable cores on ARA Per terminal/fuse blocks in the apparatus Cases/ Conductor cable termination rack.This includes all associated works of pulling out the cable from underground. The work shall be done as per location plans and instructions of Rly engineer at site.

Excavation and Casting of Apparatus Case Numbers foundation with contractors Anchor bolts, cement, ballast and other materials. Single Case as per Drg No . SK-803 SOLAPUR DIVISION-S AND T/CENTRAL RLY

Excavation and Casting of Apparatus Case Numbers foundation with contractors Anchor bolts, cement, ballast and other materials. Half Case as per Drg No . SK-804

Erection of Apparatus Cases. This includes Numbers filling of location foundations with river bed sand and plastering on top of the sand Single Case.

Erection of Apparatus Cases. This includes Numbers filling of location foundations with river bed sand and plastering on top of the sand Half Case

Installation of Eqpt. (Relays, resistance, Numbers chargers batteries etc.as applicable) & wiring of the same in apparatus Cases as per location diagrams & circuit diagrams, as per Instruction of site incharge and practice. Single Case.

Installation of Eqpt. (Relays, resistance, Numbers chargers batteries etc.as applicable) & wiring of the same in apparatus Cases as per location diagrams & circuit diagrams, as per Instruction of site incharge and practice. Half Case

Installation of earth electrode assenbly as Numbers per Drg.No.RE/S&T/SIG/Tender/SK726/85 including earth wire connected through GI wire 8 SWG supported on M.S. flat of size 6mm x 40 mm to earth electrode as per drg. No. CR/S&T/SK-815 for sigg. Equipment such as lever frames, apparatus case, signals, relay racks,block insruments, and etc. as per RE manual. The earth value should be less than 10 Ohms including the lead wire. The value should be measured in presence of Rly. supervisor. It should be documented and painted on earth enclosure made of concrete.( only earth electrode will be supplied by Railway). All other material required for provision of earthing will be brought by the contractor.

Installation RDSO/SPN/197/Ver.I or latest, to construct earthing of </= 1 ohm consisting of a. digging the earth to required depth,insertion of electrode, filling of earth enhancing compound & construction of chamber, measurement of earth value and all other work of earthing as per code of practice. All the consumables for mounting the copper tape inside the relay room, Exothermic weld materials and tools & fixtures for the welding Copper tapes and electrodes shall be arranged by the contractor. SOLAPUR DIVISION-S AND T/CENTRAL RLY

Excavation of cable trench as per cable cum route plan, 1.0 mt. deep and 300mm wide along side the track in normal soil/strata, conforming to distances as per cable route plan and refilling after cable laying. This work includes covering of cable laid to trench by loose soil for a layer of 50mm thickness after clearing of route, bushes e t c . It shall be ensured that top of the cables laid is at a depth of 0.8 m or more. If it is less, then the width and depth shall be suitably increased and accordingly proportionate payment shall be made. In case depth of trench is not achievable due to site conditions, proportionate payment will be made as per procedure. The work shall be done as per extant practice on C.Rly & the instruction of Railway engineer at site. Drg No SK 805.

Excavation of cable trench as per cable cum route plan, 1.0 mt. deep and 300mm wide along side the track in hard soil, conforming to distances as per cable route plan and refilling after cable laying. This work includes covering of cable laid to trench by loose soil for a layer of 50mm thickness after clearing of route, bushes etc. It shall be ensured that top of the cables laid is at a depth of 0.8 m or more. If it is less, then the width and depth shall be suitably increased and accordingly proportionate payment shall be made. In case depth of trench is not achievable due to site conditions, proportionate payment will be made as per procedure. The work shall be done as per extant practice on C.Rly & the instruction of Railway engineer at site. Drg No SK 805.

Cutting of all types of Roads/ platforms cum preparatory to trenching and excavation to depth of 300mmx300mm wide approx. and refilling after laying of RCC/GI /DWC pipe & to restore them to original condition. The work shall be done as per extant practice on C.Rly & instructions of Rly engineer at site.Drg. No. SK 807.

Fixing of GI pipes for crossing the culverts, Metre bridges etc. and concreting of ends with brick masonry at both ends as per the instruction of Rly engineer at site.

Digging of trench 1.0 M deep from rail cum flange/road level (for LC) and 0.3Mtrs. to 0.6 Mtrs wide and back filling after placing of DWC/RCC/GI pipe.(Placing of DWC/RCC/GI pipe coverd separately. The ballast disturbed be screened and dressed as required by Engineer-in-charge or his representatives and road tarred immediately. Drg. No. SK 806.

Laying of DWC/RCC pipes along with collars Metre in trenches at places of track and road crossings, platform cuttings etc.

Laying of signalling/Power/Telecom cable of Kilometre various cores/sizes in trenches.

Wherever depth of 0.5M cable trench is not cum feasible, cable shall be protected as under:- Preparation of cement mixture 1:3:6 with contractor's own materials and spreading cement concrete mixture layer of 100 mm thick over the already laid cables in the excavated trench. SOLAPUR DIVISION-S AND T/CENTRAL RLY

Making an entrance for new cable in old Numbers existing location, Casting concreting and curing of foundation and restoring it to old position by perfect masonry /concreting w o r k . Contractor will ensure that cable entered in Location Box is properly protected.

Horizontal boring of cable duct of minimum Metre 2.0 Mtr. depth alongwith laying of 120mm HDPE pipe for track crossing with minimum depth reckoned from the bottom of the rail/road crossing with minimum depth reckoned from ground level. The work shall be done as per extant practice & instructions of site Engineer. Prepration of site for Horizondal boring shall be carried out in presence of Railway Representative. HDPE will be supplied by Railways. Note:- Contractor shall provide all material required for boring and adequate nos. of labours for proper laying of cables into the bore. Cable shall be laid cautiously so that it should not get damage due to rough handling & pressure on cable.

Horizontal boring of cable duct of minimum Metre 2.0 Mtr. depth alongwith laying of 120mm HDPE pipe for other locations with minimum depth reckoned from the ground level. The work shall be done as per extant practice & instructions of site Engineer. Preparation of site for Horizondal boring shall be carried out in presence of Railway Representative.HDPE will be supplied by Railway. Note:- Contractor shall provide all material required for boring and adequate nos. of labours for proper laying of cables into the bore. Cable shall be laid cautiously so that it should not get damage due to rough handling & pressure on cable. BORING upto the length of 150 mtrs. Preparation of site for Horizondal boring shall be carried out in presence of Railway Representative.

Patching work in old location box consisting Numbers 1) Digging of pit, cleaning of earth from all sides, breaking of seal of location boxes removal sand from location, marking of new cable holes 2) insertion of cable from g r o u n d 3) making place for cable termination in old location, shifting ARA, fuse etc after removal and termination including fixing of ARA. 4) Termination of cable in old location 5) Filling of sand and plastering to all sides upto 50mm below ground level. SOLAPUR DIVISION-S AND T/CENTRAL RLY

Shifting of existing Full Location Boxes Numbers coming in the alignment of doubling. The work includes loosing & removal of soil around location boxes by excavating soil around foundation, making of pit for shifting of location box horizontally opposite to railway track up to 0.5 to 1.0 mtr. This includes loosing of existing cable coils without any damage. The excavated soil shall be back filled after shifting of Locaion Boxes. Location box along with its foundation shall be shifted by push method with the help of jacks or by crane by contractors own expenditure under instructions of engineer in-charge at site. Any minor repairs in foundation due to patching shall also be carried out by contracor as per instruction of Engineer incharge. The work may affect train working hence the work shall be done as per margin only or during traffic block only.

Shifting of existing Half Location Boxes Numbers coming in the alignment of doubling. The work includes losing & removal of soil around location boxes by excavating soil around foundation, making of pit for shifting of location box horizontally opposite to railway track up to 0.5 to 1.0 mtr. This includes loosing of existing cable coils without any damage. The excavated soil shall be back filled after shifting of Locaion Boxes. Location box along with its foundation shall be shifted by push method with the help of jacks or by crane by contractors own expenditure under instructions of engineer in-charge at site. Any minor repairs in foundation due to patching shall also be carried out by contracor as per instruction of Engineer incharge. The work may affect train working hence the work shall be done as per margin only or during traffic block only.

Transferring of signalling/Telecom cables Numbers from existing location box to New location box. The work include breaking/dismantling of existing foundation of locations, excavating and removing /segregating coils of this cables which may be of about 10 mtr in length .These cables are then to be disconnected and removed from the existing locations one by one as per the instructions and under the supervision of railway staff present at site. The cable is then to be inserted and terminated in new location box. The item includes neatly dressing of cables marking wiring tree etc. The material required for dressing /lacing will be arranged by contractor at its won cost. The work is required to be done systematically and with due precaution during the night block of 2.00-2.30 hrs each or within the time that may be allowed. The excavation work to be done carefully without damaging the cables to avoid undue failures. (Termination charges will be given separately) Note: Proportionate payment will be made if cable is of other length. 2/6/12/19/24/30 core signalling cable/4 or 6 Quad/PIJF/Any Signalling/Telecom Cable(One no. unit= One cable of 10 m length). SOLAPUR DIVISION-S AND T/CENTRAL RLY

Painting of two coats of synthetic enamel Numbers paint over one coat of primer on the following after scraping & cleaning surface wherever necessary with contractor' own supply of paints.Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge.Epoxy paint will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer. Apparatus Case Full Size.

Painting of two coats of synthetic enamel Numbers paint over one coat of primer on the following after scraping & cleaning surface wherever necessary with contractor' own supply of paints.Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge.Epoxy paint will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer. Apparatus case Half Size.

Lettering / Numbering of Signals, Point Numbers Machine, Track Lead Junction Boxes, Block Joints, Apparatus Cases etc. (each item to be taken as One Unit) This work will be carried out as per the standard practice being followed in Central Railway.

Lettering particulars, equipments names etc., legibly and neatly inside location boxes.Full Case.

Lettering particulars, equipments names etc., legibly and neatly inside location boxes. Half Case.

Releasing of cables from old location boxes Numbers and taking it into new location boxes. This includes excavating the earth to release the cables from old location box for taking it into new location. This also includes releasing the old location box and bringing it to nearest station / central cabin.(UNIT- NUMBERS=PER LOCATION)

Transportation material/equipments including loading and unloading in 10MT vehicle, anywhere to anywhere, and stacking at destination as per instructions of SSE in-charge as per inventory. For carrying heavy materials like cable drums, DG set, Electrical Lifting barrier pedestal, IPS, Batteries, Point machine etc. Total 14025448.46

Item Breakup - 03-NS SUPPLY AND EXECUTION

HDPE Pipe 110 mm Diameter,PE63, Class Metre PN6, with confirming to IS4984 with ISI marked (or) Latest. (Inspection by RITES) SOLAPUR DIVISION-S AND T/CENTRAL RLY

Execution of S & T work related to Job enginnering /Signalling block of CTR/TTR/TSR or others, in one block, five unskilled manpower have to be provided during block for S&T connection removing & refixing as per Railway site engineer instruction.

Steel work welded in built up sections/ Kg framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete.(Inspection by Consignee)

Portable Battery Health Tester make-Meco Numbers Bm63 or similar (Inspection by Consignee)

Supply, checking of installation, testing and Set commissioning of SMPS based integrated power supply conforming to RDSO Specifications RDSO/SPN/165/2023 Version 4.0 with latest amendments . Details as per Annexure A and Details of standard modules to be used as per Annexure IIIA with latest corrections if any. Annexure A and Annexure IIIA will be provided by Railway Engineer.(Inspection By RDSO)

Supply of CYGNUS 845-4P MULTIPLE MEDIA Pair AUTO CHANGEOVER CONVERTER-4 PORT, for simultaneously pair interconnecting Digital Axle Converter, UFSBI, Block Phone etc.across a Block Section/ IBs over multiple media. Product has the following features:.Two 120 ohm E1 Main Links with RJ45 connector, having (1+1)hot standby facility.Two optical Main Links with (1+1 hot standby dual core path and single core path) having 20 Km driving distance Four V.21/V.23 (E&M) 2-wire/4-wire user interface with auto changeover to Quad links in case of failure of all Main Links.Each user port is configurable as 2W or 4W without any restriction. Unit supports power OFF fail safe mechanism. In case the unit is switched OFF, all analog user devices are bypassed to the Quad link automatically..Unit supports four numbers of Potential free contacts which can be linked with data logger/RTU for E1 Status, Optical status & Power Supply status. .Unit supports front-panel resettable audible buzzer in case of main link fails (optical or E1) Unit supports front panel LED indicators for Quad health status, E1 dual, Optical dual path.Unit has dual hot standby DC power supply having 24VDC/48VDC Unit is 1U height with 19 inch rack mountable- facility Unit supports operating temperature from -5° C to +55°C. ( inspection by RITES) SOLAPUR DIVISION-S AND T/CENTRAL RLY

Installation charges for CYGNUS 845-4P Pair Note: 01 pair The purchase order should clearly specify requirement of installation.The scope of installation does not include any OFC Patch Cords, cabling, splicing, providing power supply arrangements, civil works etc. Working OFC, E1 and Quad Copper circuits, and power supply arrangements must be provided by the customer to start the installation work

Supply, installation, wiring, testing & Numbers commissioning of Bumpless Power Supply Autochangeover device complete along with accessories using Contractor's own wiring & fixing material as per following configuration - (i) Power Supply - AC/DC. (ii) Voltage 24V to 150V. (iii) Current Up to - 45Amp. Note: The work shall be done as per instructions of Railway's Engineer in- charge. (Inspection by RITES).

Black Godrej High Back Revolving Stool. ( Numbers inspection by Conisignee)

Supply of HSS Twist Drill Parallel shank 7.2 Numbers mm.(Inspection by Consignee)

Analog Insulation Tester (megger) Hand Numbers Driven Generator, 500 Volts, 0-100 Mega Ohms resistance Confirmed to IS: 2992- 1987, Rotation Speed: 160 rpm, Housed in ntimagnetic Metal body with collapsible handle metallic flap over the glass window scale, wide and anti-parallax mirror scale. The megger should be supplied along with carrying bag and test leads. Warranty and Calibration certificate to be submitted with megger by supplier when delivered. Make: Nippen or Motwane or Kusam-Meco (Inspection by Consignee)

Analog Insulation Tester 100 V-50 Megha Numbers Ohms, 0-600 V AC , Operating temperature 0-40 degree c,Storage temperature 10-60 Deg C, Size, 100 X 150 X 45 mm, Battery operated, Logarithmic scale, Power on/Off switch Lock for continuous measurement. High Voltage (Output) LED indicator, Insulation resistance accuracy +-5% with standard 4 No's 1.5 V batteries, Rated Out put voltage 100 V, Scale range of 0-50 Ohms, with Accessories: - Test leads with probe , Test lead with clip, Batteries, Carrying case, User Manual.. Make; KUSUM MECO Model KM 01/ MOTWANI/WACO/HTC. Accepted Make: KUSUM MECO Model KM 01 or similar (Inspection by Consignee)

1.25 mm Thick all hard blade type a Numbers Hacksaw Blade Brand: Bipico or similar (Inspection by Consignee)

ELECTRIC EQUIPMENT CONSISTING OF HEAVY DUTY ELECTRIC TRACK DRILLING MACHINE WORKS ON 110V 50HZ AC WITH SUITABLE INTER CHANGEABLE TRACK MOUNTING STAND WITH DEPTH ADJUSTING FACILITY. MAKE OF HEAVY DUTY ELECTRIC DRILLING MACHINE IS OF RALLIES OR WOLF OR BOSCH ONLY. (Inspection by Consignee) SOLAPUR DIVISION-S AND T/CENTRAL RLY

Arrangment of battery operated rail core Numbers drill alongwith additional 18 mm TCT rail core drill.Maximum core cutting capacity 36mm, rated speed 250/450ZRPM, Battery type Lion,Battery voltage 50V,Battery pack capacity 4AH,Number of battery supplied- 2No. Charger-1No. Special design pressurised internal spindle cooling to give maximum life of core cutter by avoiding heating.3 sets of of 22,13,16,7.1 gauge drills adapters to be provided along with the machine.weight of machine with battery- 18.5Kg Make:Eibenstok,Bosch,KPTL. (Inspection by RITES)

ASIAN Brushing Type Aluminium Paint Litre Brand: ASIAN (Inspection by Consignee)

Luminous Vest (Safety Jacket) (Mesh Type) Numbers as per specification Annexure 'A'. (Inspection by Consignee)

High visibility Safety reflective cross belt Numbers orange colour adjustable Grey silver tape 1- inch width, high visibility 70 to 90 GSM cloth stretches elastic, polyester and cotton mix as per specification Annexure -'B'. (Inspection by Consignee)

Supply of Concrete Earth Pit with cover. Numbers (Inspection by Consignee)

Exothermic welding of earth connection Per Weld with the material being welded. (Inspection by Consignee) Total 15660355.64