Electrical maintenance of public buildings in Kalpakkam Township for the year 2026-2027.

Amount

Maintenance of Load Distribution Panels / TPN Switch Fuse Units as per the detailed scope of work and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No.17.2).

LT Panels.

PCC panel consisting up to 3 Nos. of ACBs and Cubical Switchboards having number of vertical sections up to 5.

Maintenance of Feeder pillar (Type-C)

TPN switch Fuse unit up to 200 Amps.

Maintenance of Power and Lighting Distribution Boards located in various buildings as per the detailed scope of work and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No.17.3).

4/6/8/12 Way TPN 16/32/63 Amps MCB Distribution Boards.

4/6/8/12 Way SPN 16/32/63 Amps MCB Distribution Boards.

Maintenance of Solar Water Heater in different locations as per the detailed scope of work and as directed by the Engineer-in-charge.

Servicing and Repair of Electrical Heater (Geyser) installed at a height as per the detailed scope of work and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No.13).

Maintenance and Servicing of Rice/Idly boiler and Hot Plates, installed in kitchen as per the detailed scope of work and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No.13).

Replacement of heater coils for various electrically operated heaters as per the detailed scope of work and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No.13). Note: Heater coils will be issued at free of cost by the Department.

Attending break down maintenance of minor nature occurring in kitchen equipment such as loose connection/open circuit, changing of connecting cable etc as per the scope of work and as directed by the Engineer-in-charge.(Refer Sec VI (MNC), Clause No.15).

Supply and replacement of following heater coils / thermostat as per the detailed specification and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No.13).

230V, 1.0 kW, Single phase Heater coil suitable for BAIN MARIE

230V, 2 kW, Single phase Heater coil suitable for Geyser/Solar water tank.

230V, 3kW, Single phase, Heater coil suitable for DOSA TAWA / IDLI BOILER /.

230 Volt, 50 Hz, 0 to 85 deg. C stem type, Brass Thermostat.

Supply and replacement of the following contactors and accessories as per the detailed specification and as directed by the Engineer-in-charge.

Power Contactors, AC3 Rating, 3 Pole 32A.

Replacement of light fixtures as per the detailed scope of work and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No.21). Note: The light fixture will be issued at free of cost by the Department.

Replacement of light fixtures installed up to 4.0 Mtrs. height in various building including removal of existing fixtures.

Installation of light fixtures as per the detailed scope of work and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No.21) Note: The light fixture will be issued at free of cost by the Department.

Installation of light fixtures up to 4.0 Mtrs. height in various buildings.

Installation of light fixtures above 4.0 Mtrs. height in various buildings.

Removal of light fixtures as per the detailed scope of work and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No.21).

Removal of light fixtures installed up to 4.0 Mtrs. height in various buildings.

Removal of light fixtures installed above 4.0 Mtrs. height in various buildings.

Removal of various sizes of MS box / Switch box from the wall as per the detailed scope of work and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No.19).

Removal of various sizes of surface mounted GI / PVC Conduit / Casing and Capping from wall / column / beam and transportation to storage yard as per the detailed scope of work and as directed by the Engineer-in-charge (Refer Sec VI (MNC), Clause No.19).

Removal of the following from 415 Volts switch boards as per the detailed scope of work and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No.19).

63A/100A/125A, 500V, TP/TPN/ SFU/ Combination SFU or 4/6/ 8/ 12 Way SPN DB or 4/8 WAY TPN DBs.

250A/315A/400A, 500V, TP/TPN/ SFU/ Combination SFU 12 WAY TPN DBs.

Removal of termination of armoured cables of following sizes from electrical equipment and reconnection of removed termination as per the detailed scope of work and as directed by the Engineer-in-charge.

Sizes up to 4C X 25 sq.mm.

Sizes above 4C X 25 sq.mm and up to 4C X 70 sq.mm.

Sizes above 3.5/4C X 70 Sq.mm and up to 3.5/4C X95/120 Sq.mm

Installation of the following items on M.S.frame work (Refer Sec VI (MNC), Clause No.6). Note:TPN Switch/SDFU & DB will be issued at free of cost by the Department.

63/100/200/315/400 Amps, 500 Volt, TPN Fuse Switch Unit.

12/32/63 A, 500 V,TPN 4/8/12 Way Distribution Board

Identification and rectification of shunt or series fault in main or sub distribution panel in buildings as per the detailed scope of work and as directed by the Engineer-in-charge. .

Minor fault.

Identification and rectification of shunt or series fault in lighting or power circuit in buildings as per the detailed scope of work and as directed by the Engineer-in-charge.

Minor fault.

Identification and rectification of faults without changing accessories in various types of indoor light fixtures as per the detailed scope of work and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No.4).

Fluorescent / CFL / LED light fixtures in low bay areas.

Flourescent fittings/ SV/MV/MH fittings in high bay areas.

General maintenance or rectification of faults on Power Switch/Socket board as per the detailed scope of work and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No.22).

Attending fuse off call in Power Points / Power boards and minor faults in various Buildings as per the detailed scope of work and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No.22).

Temporary connection / disconnection of 415 Volt equipment like welding machine etc as per scope of work and as directed by the Engineer-in-charge.(Refer Sec VI (MNC), Clause No.30). Note: Required materials will be issued at free of cost by the Department on returnable basis.

Cleaning of Indoor Cable trenches as per the detailed scope of work and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No.26).

Excavation in all types of soil for cable trench including refilling with excavated earth and disposing of surplus earth at places as directed with in a lead of 10 Mtrs.. and initial lift up to 1.5 Mtrs.. including neat banking as per the detailed scope of work and as directed by the Engineer-in-charge. (Refer Sec VI, Clause No.2).

Replacement of following accessories in lighting fixtures installed in various buildings as per the detailed scope of work and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No 12).Note: Following items will be issued at free of cost by the Department.

LED Tubes

Lamp holder (Suitable for Fluorescent / CFL/ Lamps), Starter holder and Tube Light holder bracket Single/Twin.

Supply and replacement of following types of lamps / accessories up to 6 Mtrs. Height as per the detailed specification and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No.12).

7 W, 630 lm output, 6500 K, E27/B22 Cap LED Lamp.

2.7/3/5 W, 250/450 lm output, 6500 K, E14 Cap, Candle shape LED Lamp.

18 W, 1700 lm output, 6500 K, PLL LED Lamp.

15 W, 1.5 feet UV Lamp for pest-o-flash

Supply, installation, testing and commissioning of the following LED Light Fixtures of suitable lumen output as per the detailed specification and as directed by the Engineer-in-charge. (Refer Sec VI, Clause No.16.0).

Minimum lumen output of 4000 lm and minimum efficacy of 120 lm/w, 5700/6500 K, LED batten with CRCA/Steel/Extruded Aluminium housing, suitable for Ceiling, Wall and Downrod mounting.

Minimum lumen output of 2000 lm and minimum efficacy of 110 lm/w, 5700/6500 K, LED batten with CRCA/Steel/Extruded Aluminium housing, suitable for Ceiling, Wall and Downrod mounting.

Minimum lumen output of 1080 lm and minimum efficay of 110 lm/w, 5700/6500 K, LED batten with extruded Aluminium Housing, suitable for Ceiling and Wall mounting.

Minimum lumen output of 650 lm and minimum efficacy of 130 lm/w, 5700/6500 K, LED batten with extruded Aluminium housing, suitable for Ceiling and Wall mounting.

Minimum lumen output of 1200 lm and minimum efficacy of 100 lm/w, 4000/6500 K, LED Downlight with polycarbonate housing suitable for Surface mounting.

Minimum lumen output of 700 lm and minimum efficacy of 110 lm/w, 5700/6500K, IP 65 Protection LED Bulkhead with Aluminium die cast housing and polycarbonate diffused cover suitable for surface mounting.

Identification of fault and replacement of following MCB/RCCB as per the detailed scope of work and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No. 4). Note: MCB & RCCB will be issued at free of cost by the Department.

6-32 Amps, 240 Volts Single Pole MCB.

16-32 Amps, 240 Volts Double Pole MCB.

16-32 Amps, 240 Volts Double Pole RCCB.

40-63 Amps, 440 Volts Four Pole MCB.

40-63 Amps, 440 Volts Four Pole RCCB.

Supply, installation, testing and commissioning of the following RCCBs on Distribution Boards as per the detailed specification and as directed by the Engineer-in-charge. (Refer Sec VI, Clause No.14.2).

25 A, 240 Volts, 50 Hz, Double Pole, 30 mA Sensitivity Type "HPI" 'RCCB.

40 A, 240 Volts, 50 Hz, Double Pole, 30 mA Sensitivity Type "HPI" 'RCCB.

40 A, 415 Volts, 50 Hz, Four Pole, 30 mA Sensitivity Type "HPI" RCCB.

63 A, 415 Volts, 50 Hz, Four Pole, 30 mA Sensitivity Type "HPI" RCCB.

Supply, installation, testing and commissioning of the following MCBs on Distribution Boards as per the detailed specification and as directed by the Engineer-in-charge.(Refer Sec VI, Clause No.14.2).

40 - 63 A, 415 Volts, 10 kA, Four Pole "C" Series MCB.

Supply and installation of following sizes of Heavy duty, PVC, circular, rigid Conduits for Electrical & Communication System with required Solid Long Bends, Couplings JB's, GI Wire etc in Floor, Walls, Brick, Block Masonry, etc. including chasing & re-plastering as per the detailed specification and as directed by the Engineer-in-charge. (Refer: Sec VI, Clause 27.0).

25 mm Diameter, 2.0 mm wall thickness, PVC, heavy duty, round, rigid conduits with 25 mm deep Junction boxes.

Supply and external installation of following sizes of Heavy Duty, PVC, circular, rigid Conduits for Electrical & Communication System with required Solid Long Bends, Couplings, GI Wire etc, as per the detailed specification and as directed by the Engineer-in-charge. (Refer Sec VI, Clause No.27).

25 mm Diameter, 2mm wall thickness PVC heavy duty round rigid conduits with 50mm deep Junction boxes.

Supply and Installation of following sizes of PVC trunking (casing and capping) on wall / Ceiling for routing of Power, Lighting and Telephone wires including all the required accessories like Coupling, External & Internal Bends, Elbows and End Cap as per the detailed specification and as directed by Engineer-in-charge.(Refer Sec VI, Clause No.29).

25 x 12 mm size of PVC Mini Trunking.

32 X 12 mm size of PVC Mini Trunking.

Embedment of 50mm Deep, Square/RectangularConcealed type and Yellow Zinc Passivated MS boxes ofthe following types and as specified inRCC/Brick/Concrete Block Masonry with finishing andmaking good as per the detailed specification. (Refer SecVI, Clause No.15.10.8).Note: Box will be issued at free of cost by the Department.

ONE / TWO Module.

THREE Module.

EIGHT Module.

TWELVE Module.

Supply and Embedment of 50 mm Deep, Square / Rectangular Concealed type and Galvanised MS boxes of the following types and as specified in RCC / Brick / Concrete Block Masonry with finishing and making good as per the detailed specification and as directed by the Engineer-in-charge. (Refer Sec VI, Clause No.15.12).

ONE / TWO Module.

THREE Module

FOUR Module

SIX Module

EIGHT Module

Supply and Installation of following sizes of Surface Mounting Plastic Boxes as per the detailed specification and as directed by the Engineer-in-charge. (Refer Sec VI, Clause No.15.6).

ONE / TWO Module.

THREE Module.

FOUR Module.

SIX Module.

Identification of fault and replacement of following Modular Plates as per the detailed scope of work and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No.4). Note: Plates will be issued at free of cost by the Department.

ONE / TWO Module.

THREE Module.

FOUR Module.

SIX Module.

Supply and fixing of following Modular front cover plate on existing modular metal/plastic boxes as per the detailed specification and as directed by the Engineer-in-charge. (Refer Sec VI, Clause No.15.7).

ONE / TWO Module.

THREE Module.

FOUR Module.

SIX Module.

EIGHT Module

ONE Module Dummy Plate.

Wiring for lights / fans /sensors/ power point with 1100V grade FRLS insulated copper conductor wires in existing concealed / exposed PVC / ERW / Flo-coated Metal conduits as per the detailed scope of work, including supply of Wires, termination of copper wires at either end by crimping including supply of PVC Sleeves / Ferrules, Copper Crimping Lugs and connecting the wires to various switches, sockets, etc. including testing and commissioning as per the detailed specification and as directed by the Engineer-in-charge. (Refer Sec VI, Clause No.18).

1 Run of 1.5 Sq.mm Copper Wire.

1 Run of 2.5 Sq.mm Copper Wire.

1 Run of 4.0 Sq.mm Copper Wire.

1 Run of 6.0 Sq.mm Copper Wire.

Wiring for light / power point with 2 Runs of 1.5 Sq.mm (22/0.3) Copper wires for Phase & Neutral and 1 Run of 2.5 Sq.mm (36/0.30) copper wire for Earth.

Wiring for light/power point with 3 Runs of 2.5 Sq.mm (36/0.3) Copper wires for Phase, Neutral and Earth.

Supply and fixing of 3 plate, 5A, Ceiling rose on the Round block including connection as per the detailed specification and as directed by the Engineer-in-charge.

Fixing of Teak wood Round Block on Ceiling/Wall as per the detailed specification and as directed by the Engineer-in-charge.Note: Item will be issued at free of cost by the Department.

Identification of fault and replacement of following Switches/Sockets as per the detailed scope of work and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No.4). Note: Following items will be issued at free of cost by the Department.

6/10 A, 1 Way Switch.(Modular).

6/10 A, 2 Way Switch.(Modular).

16/20 A, 1 Way Switch.(Modular).

6 A, 5 pin Socket.(Modular).

6/16 A Uni-Socket.(Modular).

6 A, 240 Volts, One way Switch .(Anchor penta).

6 A, 240 Volts Bel Push Switch.

6 A, 240 Volts, 5 pin Socket.(Anchor penta).

20 Amps, 240 Volts, 1 Way Switch. (Anchor penta).

10/20 Amps, 240 Volts Uni Socket.(Anchor penta).

6A/16A Plug Tops.

Buzzer/Calling bell.

PVC Straight/Angle Holder.

230V, 20A, 2P+E Metalclad Plug Top.

230V, 20A, 2P+E Metalclad Socket.

Supply and Installation of following Wiring Accessories as per the detailed specification and as directed by the Engineer-in-charge. (Refer Sec VI (MNC), Clause No.5).

1 No, 10 A Modular Switch on Modular plate and termination of wires to the switch.

1 No, 16A Modular Switch on Modular plate and termination of wires to the switch.

1 No, 6A, 3 Pin Modular shuttered type Socket on Modular plate and termination of wires to the socket.

1 No 6/16A 3 Pin Modular combined shuttered type Socket on modular plate and termination of wires to the socket.

2 Module Step type Fan regulator on modular plate and termination of wires to the switches.

20 A Motor starter switch on Modular plate and termination of wires to the switch.

16/16A, ( Heavy duty), 3 pin Modular combined shutter type socket and termination of the wires to the socket.

Supply and installation of following general electrical items as per the detailed specification and as directed by the Engineer-in-charge. ( Refer Sec VI, (MNC) Clause No.5)

63 Amps, 500 volts, 4 way SS stud type Terminal block suitable for DIN rail mounting.

Installation of MS boxes of the following types and as specified on MS frame/Wall as per the detailed specification. (Refer Sec VI, Clause No.15.10.8). Note: MS Box/ Enclosure will be issued at free of cost by the Department.

MS/GI Box up to 150 (W) X 150 (H) X 100 (D) mm, 1.8 mm thick.

MS/GI box of size above 200(W) x 200(H) x 150(D) and up to 300(W) x 300(H) x 200(D)mm, 1.8mm thick.

Embedment of concealed type MS boxes of the following types and as specified in RCC/Brick/Concrete BlockMasonry with finishing and making good as per the detailed specification. (Refer Sec VI, Clause No.15.10.8). Note: MS Box/ Enclosure will be issued at free of cost by the Department.

150 (W)X150(H)X 80 (D) mm, 1.6 mm thick.

400(W)X300(H)X120(D)/150(D)mm, 1.8mm thick.

Supply and installation of the following sizes of copper wires in built-in-trench as per the detailed specification and as directed by the Engineer-in-charge. (Refer Sec VI, Clause No.12.8).

8 SWG copper wire.

Supply and installation of Hylam sheet covers for MS/Wooden Switch Boxes/ JBs as per the detailed specification and as directed by the Engineer-in-charge.

Supply and Embedment of following sizes of flush mounting POWDER COATED TPN / SPN DB Enclosures with Double Door consisting of Phase, Neutral and Earth Bus and interconnecting wires etc. at suitable depth in brick work as per the detailed specification and as directed by the Engineer-in-charge. (Refer Sec VI, Clause No.15.2).

TPN, 6 way Distribution Board with all accessories.

TPN, 8 way Distribution Board with all accessories.

TPN, 12 way Distribution Board with all accessories.

SPN,12 way Distribution Board with all accessories.

Supply and Embedment of following sizes Cable end termination box at suitable depth in brick work as per the detailed specification and as directed by the Engineer-in-charge. (Refer Sec VI, Clause No.15.2.2).

TPN 6 way Cable end box.

TPN 8 way Cable end box.

TPN 12 way Cable end box.

SPN, 12 way Cable end box.

Supply, open installation testing and commissioning of the following DB with Double Door consisting of Phase, Neutral and Earth Bus and interconnecting wires. (Refer Sec VI, Clause No.15.2).

TPN 8 Way Distribution Board with all accessories.

Supply and open installation of cable end termination box on as per the scope of work. (Refer Sec VI, Clause No.15.1.15).

TPN 8 way Cable end box.

SPN, 12 way Cable end box.

Open installation testing and commissioning of the following DB with Double Door consisting of Phase, Neutral and Earth Bus and interconnecting wires. (Refer Sec VI, Clause No.15.2). Note: DB Enclosure will be issued at free of cost by the Department.

SPN 8 Way Distribution Board with all accessories.

Assembling, installation, testing and commissioning of MCB DB enclosure already embedded in the wall including supply of Per phase isolation conversion kit for the following size of MCB DBs as per the detailed specification and as directed by the Engineer-in-charge. (Refer Sec VI, Clause No.15.3).

TPN 6 Way Distribution Board.

TPN 8 Way Distribution Board.

TPN 12 Way Distribution Board.

Assembling, installation, testing and commissioning of MCB DB enclosure already embedded in the wall including supply of Engraved Circuit Identification Plate and Danger Board as per the detailed specification for the following size of MCB DBs. (Refer Sec VI, Clause No.15.3).

SPN, 4/6/8 Way Distribution Board.

SPN, 12/16 Way Distribution Board.

TPN, 8 Way Distribution Board.

Supply, transportation, installation, testing and commissioning of the following Sensors as directed by the Engineer-in-Charge. (Refer Sec VI, Clause No.16).

Occupancy & day light PIR sensor suitable for lighting load of 500 W and coverage 7.0 Mtrs. diameter. The unit Shall have provision to adjust ON time as well as day light level for switching ON. (Refer Sec VI, Clause No.16.3).

Cleaning of Light Fittings/ Pesto Flash in various Public Buildings as per the detailed scope of work and as directed by the Engineer-in-charge.

Tracing of lighting and power circuits in various buildings as per the detailed scope of work and as directed by Engineer - in - charge.

Loading, Transportation, Unloading at site, Laying, Testing and Commissioning of one number PVC/HRPVC/XLPE insulated and PVC sheathed Stranded Aluminium/Copper conductor power cable of 1.1 KV grade of following sizes direct in ground including excavation, sand cushioning, protective covering with chamber burnt/cement bricks on sides & top, refilling the trench and providing RCC route indicator etc as required (Note: Cable will be issued free of cost by the department).(Refer Sec VI, Clause No.3).

3/3.5/4 Core X up to 25 Sq.mm.

3/3.5/4 Core X above 25 to 3/3.5/4 Core X up to 120 Sq.mm.

Loading, Transportation, Unloading at site, Laying, Testing and Commissioning of one number PVC/HRPVC/XLPE insulated and PVC sheathed Stranded Aluminium/Copper conductor power cable of 1.1 KV grade of following sizes in built-in trenches, on walls, poles and through embedded pipes including supply of GI spacer, clamps etc and as per the detailed specification (Note: Cable will be issued free of cost by the department).(Refer Sec VI, Clause No.3).

3/3.5/4 Core X up to 25 Sq.mm.

3/3.5/4 Core X above 25 to 3/3.5/4 Core X up to 120 Sq.mm.

End Termination of the following sizes of Aluminium Conductor PVC Insulated and sheathed armoured UG Cable using Single Compression, Heavy Duty, Gland connecting the cable to the equipment such as Switches/Panel Boards etc. using Comet or equivalent make Aluminium crimping lugs as directed by Engineer-in-Charge. The rate shall include the cost of supply of Cable Gland and Lugs. The Contractor shall arrange for making holes wherever necessary for fixing cable gland.(Refer Sec VI, Clause No.10.1).

4 Core x 10 Sq.mm including cable gland earthing.

4 Core x 16 Sq.mm including cable gland earthing.

3.5/4 C x 35 Sq.mm including cable gland earthing.

3.5/4 C x 50/70 Sq.mm including cable gland earthing.

Retrieval of the existing one numberPVC/HRPVC/XLPE insulated and PVC sheathedpower cable of 1.1 KV grade of following sizeslaid direct in ground including Removal of endtermination, excavation of trenches, retrievingof bricks and back filling as per the detailedspecification.(Refer Sec VI, Clause No.5).

3/3.5/4 Core Upto 25 Sqmm.

3/3.5/4 Core Above 25sqmm & upto120 sqmm.

Retrieval of the existing one numberPVC/HRPVC/XLPE insulated and PVC sheathed power cable of 1.1 KV grade following sizes inbuilt-in trenches, on walls, poles and from embedded pipes including removal of end termination GI spacer, clamps etc as per the detailed specification. (Refer Sec VI, Clause No.5).

3/3.5/4 Core Upto 25 Sqmm.

3/3.5/4 Core Above 25sqmm & upto120 sqmm.

Supply, installation, testing and commissioning of Automatic School Bell Controller with provision of programming minimum 5 Schedules, 40 bell timing under each schedule and password protected as per the detailed specification and as directed by Engineer-in-charge.

Supply, installation, testing and commissioning of 12" Gong Bell as per the detailed specification and as directed by Engineer-in-charge.

Supply and replacement of panel LED indication lamp Dia '22.5'mm, various colours suitable for various operating voltages from 24 V up to 240 V AC/DC. (Refer sec VI (MNC), Clause No. 12).

Colour : Red/ Yellow/ Green/ Amber.

Supply, installation, testing and commissioning of 12V,7Ah Sealed Maintenance Free VRLA Battery as per detailed specification and as directed by the Engineer-in-charge.

Periodic maintenance of 3 kVA, Single Phase input and output online UPS unit including replacement of failure components as per detailed specification and as directed by the Engineer-in-charge.

Supply, installation, testing and commissioning of 2 kW, 15 Litres, Energy Efficient Storage Geyser(Horizontal/Vertical) as per the detailed specification and as directed by the Engineer-in-charge.

Supply of paint and painting one coat on metallic surfaces of electrical equipment and other required surface at all levels with primer and following paint (Asian or approved brand, colour and manufacturer) to give an even shade including preparation of the surfaces, scaffolding complete all as per specifications and as directed by the Engineer-in-Charge. (Refer Sec VI (MNC), Clause No.3).

Synthetic enamel Paint.

Supply and Installation of MS Brackets, Supports, Frame work, Clamps, Base Channels, etc. fabricated out of angle / Channel / Rods etc. The rate quoted shall include the cost of fabrication / welding, cleaning and painting/ galvanising as follows including supply of required, fasteners, nuts, washers, etc.(Refer Sec VI, Clause No.11).

MS fabrication 1 coat primer & 2 coats synthetic enamel paint

Temporary laying of LT cables of following sizes in open air / in Built in trench. (Refer Sec VI (MNC), ClauseNo.30).Note: cable will be issued at free of cost by the Department.

Sizes up to 3.5C X 70 Sq.mm Aluminium conductor.

Supply and replacing following earth pit chamber parts after removing and disposing off old/damaged part as per drawing No. IGC/ESD/5060/1008/1.(Refer Sec VI (MNC), Clause No.2).

RCC Top cover alone

RCC ring with cover

Supply, open installation testing and commissioning of the following sizes of VTPN DBs on MS frame work (MS frame will be measured separately) as per the scope of work. (Refer Sec VI, Clause No.15.1).

VTPN 4 Way (8 Plus 12) Distribution Board, with 1 No.125A, FP Type "C" MCB and 4 Nos 63A ,3P, Type "C" MCB.

GPK ELECTRICALS (BID ID -3309157)

Bidder Name

MSE CONTRACTOR

GPK ELECTRICALS