Special repair of PHC Achina in Charkhi Dadri Distt. (Reinvite)

Amount

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing. (b) in Cement Concrete. [HSR 8.5 (b)].

Dismantling Roofing, (g) demolishing mud phaska in tile terracing (HSR 8.8 g)

Scrapping (a) White wash and colour wash (HSR 8.32 a)

Scrapping (c) Cement plaster (HSR 8.32 c)

First class brick work laid in cement sand mortar 1:6 in foundation plinth. (HSR 11.2)

Cement concrete 1:6:12 with brick ballast 40 mm nominal size in first storey upto 4 metres above plinth level (HSR 10.48)

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coasts of bitumen laid hot at 1.65 Kg per Sqm (per Square Metre) on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc.e (HSR 13.13)

Cement Concrete 1:2:4 gola 10cm x 10cm quadrant along junction of roof with parapet wall finished smooth, where specified. (HSR 13.64).

Providing & Fixing PVC Rainwater Pipe 6 kg. pressure of ISI mark in cement mortar during masonry work. (Note:- Reputed make PVC Pipe such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. [HSR 13.89]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. (a) 100 mm dia PVC pipe 6 kg. pressure.

Providing and fixing PVC Bend ISI Mark. (Note:- Reputed make PVC Bend such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge. [HSR 13.90]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. (a) 100 mm dia PVC Bend.

Lime concrete 1:1:1:8, 0.13 cum lime, 0.13 cum surkhi, 0.13 cum sand and 1.00 cum brick ballast, 20 mm nominal size in first storey, upto 4 metres above plinth level. (HSR 14.10)

12 mm Thick Cement Plaster 1:4 on the rough side of single or half brick wall. (HSR 15.5).

15 mm thick cement plaster 1:4. (HSR 15.10 )

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work. (HSR 16.60)

Providing two coats of exterior acrylic emulsion paint (HSR 16.79 b) (b) 1st quality

Supplying and fixing glass panes with deodar wood moulding-- (c) 4 mm thick (glazing area above 55 sq dm, but upto 84 sq dm of each pane) (HSR 17.24, c)

Factory manufactured paneled and glazed door shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash, etc., c(non –coniferous timber other than team, conforming to I.S specification no. 1003 kiln seasoned), with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panelsof 12 mm thick, commercial veneered both side particle board or plywood of B.W.R. grade, hot pressed, including cost of iron hinges, screws, chock/cleats stops and nails etc. complete fixed in position(excluding the cost of any fittings, other than specified above but including labour for fixing the same position. [HSR 17.91 (a) (-) 17.18 - Note]. (b) 35 mm Thick.

Factory manufactured wire gauze door and window shutters of commercial hard wood such as Hollock, Champ, Chikrassy & Chaplash only. (non-coniferous timber other teak conforming to I.S. specification No. 1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position. (Styles and rails of windows shutter shall be 75 mm wide. (i) 30 mm thick. [HSR 17.92 (i) - Note 1 under 17.18]

Factory manufactured Solid Flush Door Shutter, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hotpressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position. (Note:- reputed make such as Duro, Green, Kitply will be used as approved by Engineer-in-charge). HSR 17.93 (a) - Note 1 under 17.18]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. (ii) 30 mm thick.)

Providing and Fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers flages for connections in tanks complete in all respects to the satisfaction to the Engineer-in-Charge. [HSR 30.119]. 1000 Ltrs. Capacity Water Tank

Supply of 4mm thick DND fibre glass sheet UV mateiral in single color and providing and fixing mild steel hollow 4'' dia 4.5mm thick pipe in column and 1.5''x1.5'' 2.90mm thiock in partition and 10mm thick bottom base plate in bottom of column and 8mm thick & 12mm thick base plate top of column.All type hardware including welding job work or wastage of material with primer and paint work complete as per design or site.

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Engineer-in-charge), INDIAN TYPE ORISSA OR ORYA WATER CLOSET SUITE for sinking into floor, with raised foot treads COMPLETE WITH 100 MM H.C.I. ‘P’ TRAP with or without vent as required and all OTHER NECESSARY FITTINGS as fully described in item no.30.1 above. (HSR 30.2 b i)

Providing and fixing in position best indian make (as approved by the engineer-in-charge European type water closet suite, syphonic type consisting of- (i) VITREOUS CHINAWARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in-charge). (ii) One piece SEAT AND LID IN HOLLOW BLACK OR WHITE PLASTIC fitted with chromium plated hinges and rubber buffers, (to the approval of the Engineer-in-charge) COMPLETE in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS. (b) Double trap syphonic (ii) Single Color. [HSR 30.5 (b) (ii)].

EXTRA OVER item nos. 30.1 to 30.4 and 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY VITREIOUS CHINA HIGH LEVEL CISTERN COMPLETE with internal brass fittings instead of 12.5 litres capacity high level C.I. cistern complete (as approved by the Engineer-in-charge) (i) White (HSR 30.8)

EXTRA OVER item nos. 30.3 to 30.6 FOR PROVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow Black or white plaster seat and lid.(i) White plastic seat (Solid). [HSR 30.13 (i)].

PPROVIDING AND FIXING IN POSITION BEST INDIAN MAKE A RANGE OF THREE STALL URINALS 1150 MM HIGH IN VITREIOUS CHINAWARE WITH ONE NO. 10 LITRES CAPACITY C.I. AUTOMATIC FLUSHING CISTERN WITH FITTINGS AND FLUSH PIPE COMPLETE as fully described in item no. 30.29 above. (HSR 30.31 i)

Providing and fixing 25 mm thick marble partition for different type of urinals. Small size 680mm x 330 mm Single Color(HSR 30.40 b ii)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE LAVATORY SUITES (WITH FULL ANTI SPLASH RIM IN VITREIOUS CHINAWARE and all other necessary fittings as fully described in item no.30.41 above. White Size 510 mm X 400 mm with one no tap(HSR 30.42 i)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE CHROMIUM PLATED BRASS 2ND TAP FOR LAVATORY SUITE. (HSR 30.45)

Providing and fixing in position best quality Stainless Steel Sinks with Complete fittings as fully described in item No. 30.51. (a) 600 mm x 450 mm x 200 mm. [HSR 30.53 (a)].

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE TOWEL RAILS FIXED in with rawlslugs embedded in walls with C.P. brass screws. Complete in all respect INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (d) CP Brass two swivel towel rail 400 mm long (HSR 30.68 d)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE BEVELLED EDGE 5.5 MM THICK MIRROR mounted on ASBESTOS sheet GROUND FIXED IN POSITION BY MEANS OF 4 NOS. CHROMIUM PLATED BRASS SCREWS AND WASHERS over rubber washers and rawl plug embedded in the wall or chromium plated brass clamps with C.P. brass screws (as required by the Engineer-in-charge) COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS ETC. (HSR 30.71 a i)

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the Engineer-in-charge). [HSR 30.75]. (a) Bib cock long body.

(c) Bib cock

Providing & fixing in position C.P. brass stop cock (as approved by the engineer-in-charge). (a) 15 mm Stop cock. (ii) Concealed stop cock with flange. [HSR 30.76 (a) (i) Stop cock male and female end

(ii) Concealed stop cock with flange

Providing and fixing 15 mm C.P. brass Laboratory cock swan neck of best quality (to the approval of the Engineer-in-charge) two way (HSR 30.78 b)

Providing and fixing in position best Indian make flexible tube connection. (a) aluminium (iii) 15mm x 450 mm. [HSR 30.82 (a) (iii)].

Providing and fixing in position H.C.I. Soil waste vent or antisyphonage pipes to I.S.I. specifications of E.L.C. manufacture or of any other reputed firm including cutting and wastage etc. and cutting holes in walls, roofs or floor etc. and making good to its original condition but excluding cost of lead jointing. (HSR 30.84) (a) 100 mm internal diameter.

Cutting chase in brick wall in cement or in floor for embedding G.I. or H.C.I. pipe lines and making good the same to its original condition. [HSR 30.95 (a)]. (a) Size 75 mm x 75 mm.

MUKESH CONT