Under Special Govt. Fund Proposed Development of Garden on Rupadevi Mandir Ground Plot in Ward No.15 B of Thane Municipal Corporation Limit.

Amount

Dismantling brick masonry in lime or cement mortar and stacking the materials as directed with all leads, lifts etc.

Removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete.

Removing rich mix cement concrete including stacking the spoils as directed with all leads, lifts etc, complete.

Removing the existing cement plaster of any thickness without causing dust nuisance and stacking the debris upto a distance of 50 metres or spreading in the compound and cleaning the site etc. complete.

Excavation for foundation in earth, soils of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50 m. beyond the building area and stacking or spreading as directed, dewaterin, preparing the bed for the foundation and necessary back filling, ramming, watering, including shoring and strutting as necessary complete. (Spec.No. : Bd.A.1Page no 259/ CSR Page No.150

Transportation of excavated earth including loading and unloading per truck trip of 6.00 cubic meter capacity per trip

Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader / Paver on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- By Mix in Place Method and Grading - I Material

Providing and laying in-situ M30 Grade unreinforced plain cement concrete pavement over a prepared sub base with 43 grade cement, coarse and fine aggregate( natural sand/ VSI grade finely washed crushed sand) conforming to IS 383, using fine and coarse aggregates combined gradation as per Table 600-3 of MORTH Specification 2013,mixed in a batching and mixing plant/ non tilting mixer and Weigh batcher as per approved mix design, admixtures, transporting to site,spreading, laying with approved make paver,compacted and finished in a continuous operation, finishing to lines and grades as directed by Engineer-in-charge and curing by curing compound /by providing cement vata in cement Mortar 1:8 @0.6m X 0.6m centre to centre, admeasuring 80 mm at bottom and 40 mm at top with depth of 75 mm and maintaining the same throughout curing period by any other method approved by Engineer-in-charge.

Excavation for foundation in Hard murum including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5 to 3.0m.) By Mechanical Means

Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material upto a distance of 50 metres beyond the building area and stacking as directed, including dewatering

Dewatering on BHP basis by using water pump including diversion of stream, providing cofferdams, earthern bunds etc. as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required by using 3.0 BHP pump etc. complete.

Providing preconstructional antitermite treatment as per I.S.6313(Part-II) treatment by treating the back fill in immediate contact with foundation at the rate of 5 litres of emulsion concentrate

Providing preconstructional antitermite treatment as per I.S.6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at1.0 percent of clorophyrif as per One Square Metre of surface area covering ten years guarantee on bond paper.

Providing soling using 80 mm size granite / quartzite / gneiss / trap metal in 15 cm. layer including hand packing filling voids with sand / grit, ramming, watering complete. (Spec. No. : As directed by Engineer-in-charge /Page No. 154)

Providing and laying Cast in situ/Ready Mixcement concrete in M20 of trap/ granite/quartzite/gneiss metal for steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast insitu/Ready Mix cement concrete in M15 of trap/granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honey combed surface and curing etc.complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honey combed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic microprocess or based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying in situ/Ready Mix cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, formwork, laying /pumping cover blocks,compaction and curing roughening the surface if specia lfinish is to be provided (Excluding reinforcement and structural steel)etc.complete,with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Typemixer/concrete Batch mix plant(Panmixer) etc. complete. With fine aggregate(Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smoot hand even surface or roughening if special finishis to be provided and curing etc. complete, (Excluding reinforcement and structural steel). with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete in M-30 of trap /granite /quartzite /gneiss metal for R.C.C. beams and as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying /pumping compaction and roughening the surface if special finishis to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic microprocess or based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mixcement concrete M-30 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap/granite/quartzite/gneiss metal for R.C.C.slab sand landings as per detailed design sand drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give as mooth and even surface or rough ening if special finishis to be provided and curing etc.complete,(Excluding reinforcement and structural steel).with fully automatic micro process or based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap / quartzite /granite /gneiss metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and laying Cast insitu/Ready Mix cement concrete in M-25 of trap/granite/quartzite/gneiss metal for R.C.C.pardi of required thickness including steelentering, formwork, coverblocks, laying/pumping, compacting and rough ening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushedsand VSI Grade)

Providing and laying Cast insitu/Ready Mix cement concrete M15 of trap/granite/quartzite/gneiss metal for coping to plinth or parapet, moulded or chamfered as per drawing or as directed including steel centering, plywood/steel form work compacting, roughening them if special finishis to be provided, finishing uneven and honey combed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honey combed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.(Wooden centering will not be allowed.)With fine aggregate(Crushedsand VSI Grade)

Providing and fixing in position HCRM /CRS (Corrosion Resistant Steel) bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules .including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Providing uncoursed rubble masonry of trap/granite/quartzite/gneiss stones in cement mortar1:6 in foundation and plinth of innerwalls/in plinth of external walls including bailing out water manually , striking joints on un exposed faces and watering etc.complete.

Providing cement based water proofing treatment to terraces (Indian water proofing oralike) with brick batslaid inrequireds lopetod rainthe water foranys panafter cleaning the base surface. Applying acoa to fcements lurrya dmixed with approved water proofing compound

Providing and applying a base coat comprising of 1Kilogram Polydee-MC and 1 Kilogram fresh cement after wetting the surface followed by drying the surface for 2 days, apply primer coat of TP-40 and after drying, applying Polydee-11 two component

Providing second class Burnt Brick masonry with conventional/I.S. type bricks in cement mortar 1:6 in superstructure including striking joints,rakingout joints,watering and scaffolding etc. Complete

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

Providing internal cement plaster 12 mm. Thick in Single coats in cement mortar 1:3 with out neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc. complete.

Providing internal cement plaster 6mm thick in a single coat in cement mortar 1:3 with out neeru finish to concrete surface in all positions including scaffolding and curing etc. complete.

Providing rough cast cement plaster externally in two coats to concrete, brick or stone masonry surfaces in all positions with base coat of 12 to 15 mm thick in C.M.1:4 and rough cast treatment 12mm thick in proportion1:11/2:3 including scaffolding and fourteen day scuring complete.

Providing and applying plaster with plaster of paris in 6 mm thickness to previously plaster surface in all position including preparing the surface scaffolding etc. complete.

Providing and applying Texture plaster with finishing with texture material of approved make in 3 to 4 millimeter thickness on previously plastered surface, including Plaster Groove 6mm thickness or Tape Grooves 35 to 45 mm thickness or as required, in all position including preparing the surface, scaffolding etc. complete.

Providing and laying polished hand cut Kotah Stone flooring 25mm to 30mm thick and 45cm to 55cm wide in plain/diamond pattern on a bed of 1:6 C.M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning complete.

Providing and laying vitrified rustic matt stone finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to10 mm thicknes sand confirming to IS.15622 -2006 (GroupBla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete.

Providing and laying vitrified rustic matt stone finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm to 8 to10mm thickness and confirming to IS.15622 -2006 (GroupBla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning. etc. complete.

Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete

Providing and laying telephone black / Amba White / Cadburybrown /Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing the sharp edges wherever necessary, curing, etc. complete.

Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Catbary brown / RBI red / Ocean Brown granite stone for tread sand risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete.

Providing leather finished polishing to Granite Stone slab by continuous grinding in 4 coats of different bits to receive rough and matt finish including buffing process before laying and fixing of stone as per drawing and design,including cleaning,washingand finishing etc. complete.

Providing and fixing M40 grade thick vibrated pull cast or similar type concrete frame with chamfer conforming to I.S. 65241983 having 6 mm dia. bars 3 Nos. And stirrups @250 mm c/c and fixing in wall with 6 Nos of hold fast of 12 mm dia bars 500 mm long including primer and oil painting etc, complete) frame size 60 mm x 100 mm .

Providing and fixing factory made solid core flush door in single leaf 35 mm thick, decorative types,of exteri or grade,as per detailed drawings,conforming to I.S.:2202-1962 (Revised) with approved face veneers

Providing and fixing Country cut teakwood double or single leaf second class fully panelled door shutter with 35 mm thick style and rail with 25 mm thick panels with openable fan light as per detailed drawings. Excluding the door frame 60 mm x 100 mm stainless steel fixtures and fastening and finishing the wood work with oil painting 3 coats. (Excluding the door frame)

Providing and fixing fiber glass reinforced polyster door shutter 35 mm thick as per IS 14856 (2000)(Reaffirmed 2006) without ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, etc complete.

Providing and fixing collapsible steel gate in one/two leaves with hot rolle dvertical channels of 18x9 x3 mm minimum size,crossing so fM.S. flats of size 18 x 5mm Tor Esection forrunner of minimum 40 x 6 mm size for flange,M.S.flat for top runner of minimum size 40 x12 mm with roller wheels confirming to grade

Providing and fixing in position (as per 1868/1982) Alluminium sliding window of three tracks with rectangular pipe 95x38.10x0.90 mm at weight 0.637 Kilogram/One Running Metre. with window frame bottom track section 92x31.75x1.30 mm at weight 1.070 Kilogram/One Running Metre. Top and side track section 92x31.75x1.30 mm at weight 0.933 Kilogram/Running metre. The shutter should be of bearing bottom 40x18x1.25 mm at weight 0.417 Kilogram/One Running Metre. Interlocking section 40x18x1.10 mm at weight 0.469 Kilogram/Running metre. and handle and top section 40x18x1.25 mm at weight 0.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineer incharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing innyl on casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With colour Anodising with box

Providing and fixing frame with / without ventilator of size as specified with Country cut teakwood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete

Providing and fixing in position powde rcoated aluminium louvered windows /ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type,5 mm thick sheet glass louvers, of approved quality etc. complete.

Providing and fixing in position aluminium partly openable and partly fixed window of any size as per detailed drawing and as directed by Engineer incharge with all necessary alluminium sections including necessary fixtures and fastening with 5 mm thick float glass etc. complete. b) With powder coating Note Whilearriving at the rate of item of item weight at 6.90 Kilogram/Square Metre is considered.

Providing and fixing green marble of 18 to 20mm thick for door frame/dado/window boxing etc.On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete.

Providing and fixing mild steel grill work for windows,ventilator setc.20 Kilogram/Square Metre as per drawing including fixtures,necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.

Providing and applying white-wash in one coat on old/new plastered or masonry surface sand asbestos cement sheets including scaffolding and preparing the surface by brushing and brooming down etc. complete.

Providing and applying washable oil-bound distemper of approved colour and shade to old and new surfaces in two coats including scaffolding, preparing the surfaces. (excluding the primer coat.) etc. complete.

Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete.

Providing and applying two coats of textured synthetic paint of approved shade and quality and one coat of primer before applying textured paint including scaffolding if necessary preparing surface by thoroughly cleaning oil, grease, dirt and other materials as required, etc. complete.

Providing and applying two coats of lead/zinc base oil paint/ bituminious paint of approved colour to new structural steel work and iron work in buildings including scaffolding if necessary, cleaning and preparing the surface etc. complete. (excluding primer coat).

Providing and applying two coats (exterior quality) of flat oil paint of approved colour and shade to the plastered surface in buildings and workshops including scaffolding if necessary, cleaning the surface and preparing surface etc. complete. (excluding primer coat)

Providing and applying two coats Apex Ultima Puranature Anti- Pollution Or equivalent approved brand, paint should decomposes organic substances and inorganic gases(NOx, VOC’s, CO, SOx,formaldehydes, etc.) in presence of natural or artificial light. It contains Graphene and nanoparticles of titanium oxide. and Absorbs CO2 (4.8 kg/15 l). plaster crack should be filled by Acrylic base Crack seal/Textured Crack filler, Paint has to applied on one coat of Apex Ultima Puranature Anti-Pollution Primer or Equivalent. Warranty Should be given by the Manufaturer The work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise onsite technical reports from the concerned company technologist.

Providing and fixing false ceiling of 15mm thick as per drawings including powder coated G.I.wall angle of 20mmx20mmx0.60mm size,G.I.grid runners of size15mmx38mm at 600mm center to center both ways and suspended using G.I.3mm wire including fixing using butterfly clip sand fasteners including transporting,scaffolding all necessary labourand machinery, finishing etc. complete.

Providing and fixing Orissa Pan of size 580x445x260 mm with approved make flush valve including trap, C.I. soil and vent pipe upto outside face of wall including 100mm dia. C.I. plug, bend and necessary pipe connection, etc complete. As directed by Engineer in charge.

Providing and fixing white Opal series European type wall-hung, of size 400mm x 370mm x 575mm with approved make flush valve including soil pipe, vent pipe upto outside face of wall, 100mm dia C.I. plug bend inlet pipe all fittings, cutting & making good walls, floors etc as directed by Engineer in charge.

Providing and fixing Table top white wash basin of size 120x635x405 mm rubber plugs and brass chain,with pillar cock, C.P. Angular stop cock long thread, continental including S.S. bottle trap of approved make having necessary pipe connection upto the out side face of the wall.etc complete as directed by Engineer in charge.

Providing and fixing 450 mm x 550 mm size superior type Belgium mirror with 16 mm dia. nickel plated towel rod etc. complete.

Providing and fixing chromium plated towel rod 16 mm dia and 75cm. In length including all accessories complete.

Providing and fixing 10cm C.I. Nahani Trap including C.I. grating bend and piece of C.I. pipe upto the outside face of the wall complete.

Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap.

Providing and fixing on walls/ ceiling /floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stackingt he same in PWD chowky or as directed etc. Complete

Providing and fixing on walls/ ceiling /floor 25mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipeline if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls /ceiling /floor 50 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete.

Providing and fixing 15 mm dia. Screw down bib /stop tap of brass including necessary socket union nut complete.

Providing and fixing 25 mm dia. Screw down bib / stop tap of brass including necessary socket union nut complete.

Providing and fixing screw down 15 mm dia. Wheeled stop tap of brass including necessary sockets/union nut complete

Providing and fixing screw down for 25 mm dia. Wheeled stop tap of brass including necessary sockets /union nut complete.

Providing and fixing screw down for 50 mm dia. Wheeled stop tap of brass including necessary sockets/ union nut complete.

Providing and fixing push cock (Self closing tap) symet type of 15mm dia.including necessary socket, testing etc. complete.

Providing and laying for 225. mm dia salt glazed stoneware pipe including fittings Such as bends, tees, single junction, double junctions laying, jointing (including excavation and refilling the trenches) complete.

Providing and fixing 50 mm dia meter water meter with non-return valve including strainer, sockets /union nut and including water meter box making locking arrangement and lock. [without chamber]

Providing andc onstructing Brick Masonry Inspection Chamber 90cm x 45cm With R.C.C. raft in B.C. soil area including cost of reinforcement, 1:2:4 cement concrete channel shalf round G.S.W. pipes, Brick Masonry, plastering from inside and air tight with 75 mm thick R.C.C. cover medium duty 140 Kilogram etc. complete.

Providing and fixing ISI1729/2002 grade 100mm dia Cast Iron Soil Pipes With lugs including plug bend necessary fittings such as bends, tees, single junction, double junction, slottedvent, off sets on wall orinto the ground including filling joints with cement mortar 1:2 proportion fixing on wall by means of galvanised Mild Steel bracket of 30x5mm plate and 8mm square rod with Galvanised Iron clamp with wash erasper design, drawing and as directed to keep pipe 50mm away from wall including necessary scaffolding and painting the exposed faces with one coat of red lead oil paint and two coats of white oil paint including removing the existing pipe if necessary and conveying and stacking in PWD Chowky or as directed by Engineer-in-Charge.

Providing and fixing P.V.C. Rain water pipes of 160mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number, filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.

Automated Toilet - Duplex Unit Toilet 1. Completely auromated toilet with facility of automatic light on of and auto flushing facility. 2. Light in weight, modular, portable & easy to shift. 3. Leakage proof. 4. Weather proof with high ESCR. 5. As it is portable considered as temporary structure, not counted in FSI

Providing and fixing corrugated galvanised iron sheets of 0.63mm thick (24B.W.G.) for roofing without wind tiles including fastening with galvanised iron screws and bolts,lead and bitumen washers as per drawing etc. complete.(Weight of 5.5 Kilogram/sq.m.).

SS Dust Bin two sides for extra strength during oscillating movement. Oscillating arrangement for easy unloading of Garbage. Area :0.765 Sqm , Capacity In Litres 42 Ltrs, Height : 0.92m

Providing and fixing 900 mm high S.S. 304 Grade Stainless steel railing with 40 mm diameter and 1.5 mm thick at top, 40 mm diameter and 1.5 mm thick vertical supports spaced at 1.5m center to center and 8mm thick toughened glass including fabricating, fixtures, errecting, necessary welding , grinding , finishing, buffing to stainless steel pipe etc. complete

Providing and fixing informatory sign boards of size 60 cm x 80 cm made out of 14 guage Aluminum sheet bonded with IRC Specified colour of retro reflective sheeting of Type IV High Intensity Micro- Prismatic Grade Sheeting (HIP) having pressure sensitive / heat activated adhesive, IRC Specified colour retro reflective cutout border & messages having pressure sensitive adhesive having border & messages in IRC Specified colour background including M.S. angle iron post of size 65 mm X 65 mm X 6 mm, 3.65 m long, duly painted with flat oil paint having alternate black and white bands of 25 cm width including G.I. fixtures etc; fixing the boards in 1:4:8 concrete block of size 60cm X 60cm X 75cm including transportation etc; complete. Alluminium sheet Type IV High Intensity Micro-Prismatic Grade Sheeting.

Providing and fixing 50 mm. dia. medium class G.I.pipe gate with wicket gate of approved drawing with all fixtures and fittings in two leaves with strong hold fast embedded in c.c. block at top and bottom with locking arrangement including cutting, bending, making holes and with one coat of primer etc. complete.

Providing and fixing Mangalore tiled roofing with class 'AA' tiles including securing the last course of tiles near the eaves with steel flat 40 mm x 3 mm and 1.22 mm wire fixing country teak wood sloping battens of 25 x 12 mm teak wood horizontal battens of 50mm x 25mm over the slopping battens, all iron work and coal tarring the battens etc. complete (Excluding ridge and hip tiles

Providing,fabricating and supplying and fixing panels of aluminium composite panel (ACP) cladding in pan shape in metalic colour of approved shades made out of 4 mm thick aluminium composite steel panel material consisting of 3mm thick FR grade mineralcore sandwiched between two aluminium sheets(each 0.50mm thick). The aluminium composite panel cladding sheet shall be coil coatd with kynar 500 base PVDF/Lumiflon based fluropolymer resin coating of approved colour and shades on face 2 as specified using steinless steel screw, nuts, bolts, washers, clets, weather silicon, sealent, backers rods etc. The supporting frames structure shall be made of aluminium rectangular section 38x38 mm. The fastening brackets of aluminium alloy 6005 T5/MS with hot deep galvinised. (As per previous approved rate)

Providing and supplying waterproof tensile mild steel Modular Roof Terrace Structure with 15 Feet height as per drawing and as per instructions from Engineer in charge.

Providing, hoisting and fixing at all level precast or reinforced cement concrete gazebo with all elements like roofing, string courses, bands, copings, columns, pillars beams, plinth beams, railings, benches, flooring, foundations including architectural design, moulding, arches, shapes and applying proper texture and planning coats to suit a particular asthetic element (truck of trees, shapes of animals, birds, tiber, benching, any element or structure representing culture or tradition) the cost of required centering, shuttering and reinforcement, of M25 grade and fibrous material, etc complete as per the instructions of architect or engineer-in-charge.

Providing and fixing decorative M.S. pergola a structure built with columns or posts that support the rafters above pathway of size 3 x 1.5m and 3m height finished with desired wooden textured paint. (Note:- Rate Approved in Tender of Integrated Garden)

Providing and fixing H.D.P container Syntex or alike one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery upto destination hoisting and fixing of accessories such as inlet, outlet over flowpipe in clusive of all tanks capacity between 200 to 1000 liters

Providing and fixing 45 cm wide mild steel ladder of 40 mm x 6mm mild steel flat stringers and steps of 18 mm dia.mild steel bar for water tank including fixing it in(1:2:4)M-15 cement concrete block 60 cm x 30 cm x 30 cmand painting the ladder complete.

Providing and fabricating structural steel work inrolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted/bolted/welded connections with out connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete.

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15cm to 20cm including watering and compaction etc.complete.

Excavation for foundation in soft strata which does not required blasting up to 1.5 Mtr. depth including removing the Excavated material up to a distance of 50 Mts. beyond the building area and lift. (PWD-DSR 2015-2016) P-5 / I-A-1

GARDEN SOIL :- Supplying on site garden soil well sieved 90% to pass through I.S. sieve of 10mm size Free from stones rubbish like dried grass roots and other such materials. The soil should be fresh be measured by measuring box (Farma) Item includes royalty charges, octroi, corporation Tax Transporting, loading – unloading etc As derected by Engineer-Incharge.

Farm yard manure :- Supplying on site well decayed, well dried, well powedered, withought clods and free from stones, dried grass and other rubbish material,. The colour of the manure generally be black. the manure will be measuring by measure box. (farma) item includes Transporting, loading -unloading etc (lead charges per 40km. are considered.

Preparing Shrubbery :- Excavating the round to required depth of 30cms, removing and conveying unwanted stuff to a required excavated area in 3:1 proportion to a height of 30cms. Mixing garden soil & manure toughly well, leveling , watering on previous As derected by Engineer-Incharge.

Preparing Instant Lawn : Excavating the ground to a required depth of 20cms removing & conveying unwanted stuff to a required distance as directed. filling fresh garden soil / silt & manure in excavated area in 3:1 proportion to a height of 20cms.

Providing and Fixing Decorative/Ornamental grills as per design for compound wall/Fencing including fabricating the grill using M.S. square / round bar, flats and angles including painting with one coat of red oxide zinc chromate primer and two coats of synthetic enamel paint of approved colour and brand etc. complete as directed.

Providing and fixing mild steel grill gate as per the detailed drawing including hinges,locking arrangements and painting in three coats of oil paint of approved colour and shade etc. complete. (weight 18 Kilogram. to 20 Kilogram. Per Sq.m.) Spec. One Number: As directed by Engineer- in-charge.

Providing and applying Ferro cement cladding of reinforced concrete with thin walls that's made of cement mortar and closely spaced layers of wire mesh on existing M.S. framework with thickness of 20-25 mm. (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

GRC - Glass Reinforced Concrete Roman columns to be provided and fixed of 12' height and 0.5m dia (as per design shared by architect) (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing and fixing GRC (Glass reinforced concrete) cladding on the premade m.s framework for are above column comprising of (Architrave/Frieze/Cornice) size - 1.5m(height) x 25m(length) x 0.75m (Thickness) to be made as per design shared by architect (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing and fixing mild steel grill gate with angle iron frame 65mm x 65mm x 10mm with iron bars at 150mm C/C and diagonal flats as per the detailed drawing including hinges, pivot block locking arrangement, welding riveting and oil painting of three coats of approved shade Weight of gate 35 Kg/Smt.

Kid’s Play Area- Rubber flooring Providing and Applying Ethylene-propylene diene monomer (EPDM) is a durable and versatile M-class synthetic rubber poured in place on-site, providing a seamless surface of 8-10 mm thickness. (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing and erecting chain link fencing 1.6 M. height with G.I. chain link of size 50 x 50 mm, 8 gauge thick and fixed 75 mm above ground level on vertical M.S. Angles of 40 x 40 x 6 mm size, includind excavating pits for foundation and embedded in C.C. block of 1:4:8 mix of size 450 x 450 x 670 mm. at 1.75 M. c/c with iron bar 16mm dia as hold fast including welding link with angle frame at 30 cm c/c with nuts and bolts and horizontal M.S. Angles at top and bottom of 25 x25 x 5 mm size and vertical M.S. flat 35 x 5 mm and 25 x 5 mm orizontal including cross support of 40 x 40 x 6 mm angles both side at every corner or bend embedded in concrete blocks of 1:4:8 of size 450 x 450 x 670 mm including 3 coats of oil painting etc. complete.

Riders - Providing and fixing FRP (Fibreglass reinforced plastic) riders. (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing and fixing Double Toddler Swing (PASW04) Equipment area - 1.8m x 0.97m Safe Play Area - 3.0m x 3.5m Ideal for age - 2-5yrs (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing and fixing Multi-purpose Play System Equipment area - 13.0m x 8.4m Safe Play Area - 16.0m x 11.4m Ideal for age - 4-12yrs (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing and fixing play area Combination Set made in metal and FRP (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing and fixing Double Arch Swing (PASW05) Equipment area - 3.1m x 1.08m Safe Play Area - 4.3m x 5.0m Ideal for age - 5-10yrs (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing and fixing FRP multi see-saw. (PASE03) Equipment area - 3.0m x 0.5m Safe Play Area - 4.5m x 1.5m Ideal for age - 4-12yrs (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing and fixing Scrambler Set (PARS07) Equipment area - 6.2m x 6.7m Safe Play Area - 9m x 9m Ideal for age - 8-13yrs (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing and fixing Balancing Bridge (PACL03) Equipment area - 6.2m x 1.05m Safe Play Area - 8.6m x 2.5m Ideal for age - 6-12yrs (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing and fixing Multi Purpose Scrambler Set(PACL26) Equipment area - 11.8m x 3.4m. Safe Play Area - 14m x 5.5m. Ideal for age - 8-13yrs (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Kilkari MS with Powder Coated Merry Go Round 04 Seater Shape:- Round Material:- MS with Powder Coated Age Group:- 6-12 Safe Play Area:- 2.2 m Dia

Providing & Supplying & installation of Aerial Stroller (ODFE01) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 1.12m x 0.35m Safe Area - 2.12m x 2.55m (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing & Supplying & installation of Chest Press Single (ODFE02) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 1.2m x 0.7m Safe Area - 2.8m x 2.2m (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing & Supplying & installation of Chest Press Double (ODFE02) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 2.1m x 0.7m Safe Area - 4.0m x 2.2m (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing & Supplying & installation of Seated Puller Single (ODFE04) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 1.2m x 0.8m Safe Area - 3m x 2m (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing & Supplying & installation of Leg Press Double (ODFE05) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 2m x 1.1m Safe Area - 3.5m x 2m (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing & Supplying & installation of Triple Standing twister (ODFE08) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 1.6m x 1.5m Safe Area - 5m x 3.5m (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing & Supplying & installation of Elliptical (ODFE09) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 1.1m x 0.6m Safe Area - 3.5m x 2m (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing & Supplying & installation of Arm Spinner - 2 wheel (ODFE10) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 0.7m x 1.3m Safe Area - 2m x 3m (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing & Supplying & installation ofAbs Board Double (ODFE17) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 2.4m x 1.4m Safe Area - 4.5m x 2.2m (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing & Supplying & installation of Knee Hip Riser (ODFE18) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 1.06m x 0.95m Safe Area - 3m x 1.8m (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing & Supplying & installation of Chest Press + Seated puller (ODFE27) etc.complete.Spec.- As Directed Engineer-in-charge. Equipment area - 2.4m x 0.8m Safe Area - 4.8m x 2m (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing and fixing of sandstone bench made with desired shape and designs of size 59"x16"x16" Colour - Chocolate & Teak stone (Note:- Rate Approved in Integrated Gardens)

Providing and fixing of sandstone bench made with desired shape and designs of size 85"x17"x40" Colour - Rainbow Stone (Note:- Rate Approved in Integrated Gardens)

Providing and fixing FRP (Fibreglass reinforced plastic) Murals on the given base wall of thickness ranging from 100mm to 300mm given a 3d effect of desired shapes and designs. (Note:- Rate Approved in Integrated Gardens)

Providing and supplying FRP (Fibreglass reinforced plastic) Statue of different shapes and designs of size: L 6ft-8ft and height 5ft - 6ft. (Note:- Rate Approved in Integrated Gardens)

Providing and supplying GRC (Glass reinforced concrete) Statue of different shapes and designs of size: L 6ft-8ft and height 5ft - 6ft (Note:- Rate Approved in Integrated Gardens)

Designing, Conceptualization & painting of 3D artistic on any surface at all height and location as directed. The paint should be used for the artistic painting is high quality acrylic paint. painting should be coated with weather proof warnish.

Providing and fixing Circular Dolphin Water Fountain with stainless steel 304, 14 Gauge ring with nozzle tapping, bending and rounding, S.S. stand, Cascade Coupling and Fiber Dolphin Sculpure and Construction of RCC 5 dia mtr waterbody, tiles work, waterproofing & Miscelleneous work

Installing & Assembling Drip Irrigation System

Drilling of borewell upto 300 ft. & Installation of 5HP Submersible Pump As directed by Engineer incharge

Providing and Fixing Topiary Garden Sculpture – Mural made in MS structure frame work covered in wire mesh from outside with vegetation on framework to get desired shape Height 2.5m x width 1.0-1.2m x thickness 0.75m (Note:- Rate Approved in Tender of Various Gardens in Owala Majiwada - TS No. 100)

Providing sculpture on wall including formation mould and fixing on wall completed

Providing and fixing heavy duty inter locking concrete Rubber mould glossy paving blocks of 80 mm thickness of having a strength of 400 Kilogram/Sq.cm. of approved quality and shape on a bed of crushed sand of 25 to 30 mm thick including skirting joints and cleaning etc. complete. (using 100% crushed sand)

Providing and laying concrete pipes of I.S.NP. class of 225mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete

Compacting the sub grade/gravel/oversize metal (200 mm loose) layers for all width with Vibratory roller having weight 8 to 10 MT. including necessary, labour, materials and artificial watering complete.

Providing and laying weep holes of 100 mm diameter PVC pipes as per drawing for abutment returns, return walls etc. Complete.

Point wiring for light/fan/bell in 20 mm HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire with flush type switch and required accessories as per specification no. WG-PW/SW

Point wiring for light/bell concealed type in min 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WGPW/CW

Point wiring for light/bell/exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification no. WG-PW/SW

Point wiring for ceiling fan concealed type in min 20 mm HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification no. WG-PW/CW

Point wiring for independent plug in 20 mm HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire,flush type switch, earthing and required accessories as per specification no. WG-PW/SW

Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 8 module duly flushed to wall with required chiselling and finishing with cement mortar / POP as per required to match thebackground.

Supplying and erecting PVC Surface modular double mounting plate 2 module complete duly erected.

Supplying and drawing of 2x1.5 sq.mm. FRLSH grade copper wires with 1.5 sq.mm earth wire in provided concealed pipes and terminating on modular accessories in box for point wiring for independent plug as per specification No WG-PW/SW

Supplying and erecting mains with 3x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying and erecting mains with 3x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying & erecting HMS PVC conduit 20mm dia. with necessary accessories in wall/floor with chiselling appropriately as per specification no. WG-MA/CC

Supplying & erecting HMS PVC conduit 25mm dia. with necessary accessories in wall/floor with chiselling appropriately as per specification no. WG-MA/CC

Supplying and erecting PVC trunking (PVC casing-n-capping) of size 20mm with accessories on wall/ceiling as per specification no. WG-MA/CON.

Supplying and erecting PVC trunking (PVC casing-n-capping) of size 25mm with accessories on wall/ceiling as per specification no. WG-MA/CON.

Supplying, installation and testing of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete, and recording the results Specification no. EA-MOBI

Supplying and erecting GI strip of high purity required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint with joints required. As per specification no EA-EP.

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 90 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Providing & erecting hot dipped galvanised perforated type cable tray manufactured from16SWG GI sheet of 150mm width & 75mm height complete with necessary coupler plates & hardware.

Supplying and erecting Energy Saving Ceiling fan of 3 star rating as per BEE 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Supplying and erecting electronic type step regulator for ceiling fan 600/ 900/1200/ 1400 mm. sweep, complete erected on provided switch board.

Supplying and erecting fan clamp of 30 x 5 mm. M.S. flat of required length and 10 mm. M.S. bolt and nuts erected with necessary hook of 10 mm. M.S. round bar and painted

Supplying and erecting fan hook of 10 mm. M.S. round bar grouted in RCC slab with making the site as original.

Supplying and erecting exhaust fan medium duty 230 V A.C. 50 cycles 225 mm. 1400 RPM with condenser complete erected in position with necessary materials.Fan motor with moisture proof treatment and ‘E’ class insulation.

Supplying & erecting 5W-7W, 230V integral type LED Lamp suitable for B 22/E-27 base as per specification no. FG-LP.

Supplying and erecting LED square / circular Max. 11 W down lighter/Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 1200 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting LED square / circular Max. 18 W down lighter / Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B0 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with minimum 2 years warranty as per specification No. FG-IDF/LED.

Supply of 20 W LED batten WH PVC (5700K to 6000K) CRI>70%, Lumen efficacy> 100 Lumen per watt, voltage 230V AC

Supplying and erecting anodized aluminium mirror light LED fitting (2 feet) Max. 12W with high transitivity diffuser with min. system lumens output of 1200 lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<20%, p.f. >0.95, operating range of 200-270V,surge protection of 2 kV, Life class of 50,000 Hrs at L70B50 including driver with end caps on provided PVC Block / wooded board with minimum 2 years warranty as per specification No. FG-IDF/LED.

Supplying and erecting LED Panel Light (600mm X 600mm) Max. 25 W having CRCA powder coated housing, polystyrene diffuser having system lumens output of Min 4200 Lumens, min. efficacy of 120 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B50 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with minimum 2 years warranty as per specification No. FG-IDF/LED.

Supply Installation Testing & commissioning of integral high pressure Die cast/extruded aluminium LED Floodlights luminaire with proper heat dessipation & toughned glass protector or with yellowing injection molded polycarbonate cover having high light transmission index.The LEDs are provided with suitable lens for dispersal for achieving street light optics to ensure uniform light distribution.The LED fixture shall be desighned for at least L70 life of minimum 50,000 burning hours at ambient tempreture not less than 35*C. the system wattage (fixture's total power consumption) should be be 120W. Details as per technical specification attached.

Providing & erecting 7 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL

Supply Installation testing and commissioning of Decorative Pole Technical Description :- 2955mm pole made of gravity die cast aluminium (LM6). Bottom Florus decorative element dimension details (245mm Dia x 206mm Height). Decorative base made of gravity die cast aluminium (340mm dia x 516mm Height). Decorative element (190mm dia x 550mm height) mounted on base and continuously tappered decorative flutted pipe made of gravity die cast aluminium (126mm Bottom Dia & 112mm Top Dia x 1000mm Height) fitted on decorative element with decorative die cast aluminium embellishment for mounting four arm bracket. Bracket stem made of MS square 120mm with decorative die cast aluminium embellishment of 375mm height with flower bud design on top 202mm. The four arm bracket made of gravity die cast aluminium extending from stem is spruced up with Leaf designer embellishment and facilitates the fitment of post top luminaire at 445mm on four side from the vertical axis of the bracket stem.Pole section welded by certified welders using high end Magnesium Inert Gas welding processes. Any other internal cables and connections shall not be covered in the scope of supply. Mild steel mounting plate 200mm square x 12mm thick steel of grade E250 to IS 2062 : 2011 with 4 elongated holes 38 x 19 to suit M16 x 300mm bolts of grade 4.6 at CC 140. The base plate have a cable entry hole of 70mm dia at the center. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation. All dimension within +/- 5% tolerance. After fabrication, entire pole is shot blasted (Inhouse). After shot Blasting the pole should be coated with zinc rich primer & pure polyester powder coating or epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint (coating thickness 60-80 microns). The Pole shall be provided with Graphite grey / Anthracite grey / Black as standard colour options and Gold / Antique shade as special colour options.

Fitting:Supply Installation testing and commissioning of 50W Post Top Luminaire Technical Description : Pole-top luminaire with Symmetrical light distribution. Luminaire made of spun aluminium, die cast aluminium and non corrosive stainless steel fasteners. Cast aluminium magudam attachment added for aesthetics. Prismatic diffuser. Suitable for mounting on Ø76 mm OD pipe. Pure polyester powder coated graphite grey & gold / anthracite grey & gold / jet black & gold. Available colour temperature 2700K / 3000K / 4000K / 5700K, Colour rendering index (CRI)>80. SDCM-3 MacAdam. LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency >85%, Power factor >0.95, THD <10%, Surge protection 6KV. Input operating voltage range of 100-300 Vac. The driver shall have short circuit protection with automatic restart, Overvoltage Protection, thermal protection and No load protection. Led Source shall be of Nichia / lumiled/Cree Equivalent Make and shall be of standard deviation colour matching to 3 Step Mcadam. External SPD of 10KV shall be provided along with the fixture.Luminaire dimension : 495mm diameter x 960mm height. BIS Certified for Luminaire.

Supplying and erecting LED Green Flood light fitting of 50W, including lamp, with PF>0.95, Class IP 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete per specs no. FGODF/FLS-2

Supplying and erecting LED Strip light 5m Length Max. 8 W/mtr IP65 class including necessary components. The LED Strip shall be protected with transperent PVC material.

Supply , Installation, Testing and commissioning of 4270mm height pole made of circular mild steel pipe (grade YST 210) 88.9mm Dia x 2.9mm thick with 2788mm Height. Decorative base made of Gravity Die- cast aluminium (245mm Dia x 206mm Height) in gold or black finish. The single am bracket is a split constructed type, bracket stem made of MS Pipe 60.3mm Dia x 2.6mm thick, emerging from a Gravity Die cast mid section Aluminium embellishment in gold or black finish of 60mm with a clear height of 1150mm crowned at top from the collar and with a cast Iron decorative finial of 260mm dear height. The artistically curved single am made of MS pipe 38.1mm Dia x 2mm thick. spruced up with MS Scroll with leafy embellishment at Center in gold or black finsh , is firmly held to the stem by way of cast iron clamps and the arm bears cast iron knobs at the one ends and other end facilitates the fitment of luminaire at 624mm from the vertical axis of the bracket stem. Pole section welded by certified weldem using high end Magnesium Inert Gas welding processes. Pressure Die Cast aluminium service door 348mm height x 80mm width shall be provided with the company logo embossed on the bottom of the door and safety rope. The bottom of the door is loacted at a height of 500mm from its base plate. The control gear tray is prewired with single Core 2.5 Sq.mm PVC wire, 6A SP MCB of approved make and with 3ZA stud type 4 way teminal block to take incoming cables with loop-in / loop-out arrangement and to be connected with lugs and has a 5 amp. 2 way terminal connector for luminiare and a provision for earthing. Any other internal cables and connections shall be covered in the contractors scope. Mild steel mounting plate (Base Plate) 230mm Dia x 12mm thick Steel of grade E250 to IS 2062 : 2011 with 4 elongated holes 38 x 19 to suit M16 x 300mm bolts of grade 4.6 at Pitch Center Distance 180mm. The base plate have a cable entry hole of 70mm dia at the center. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed foundation. All dimension and are within +l- 5% tolerance. After fabrication, entire pole should be shot blasted (lnhouse). After shot Blasting the pole should be coated with zinc rich primer & pure polyester powder coating or epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint (coating thickness 60-80 microns). The Pole shall be provided with Graphite grey / Anthracite grey / Black as standard colour options.

Supply installation testing and commissioning of Tier drop Luminaire of 70W.Decorative pendant / Hanging mounted compact street light. Type IV (Asymmetrical light distribution). Decorative luminaire made of specially contoured spun aluminium body of high corrosion resistance with a neck design for unique and better aesthetics and non corrosive stainless steel fasteners. Clear polycarbonate diffuser. The luminaire have extruded aluminium heatsink fbr thermal management with vertical fin design for longerlife of the LEOs. The mounting arrangement nipple, coupling & Hex nut made of Stainless steel 304 suitablefor mounting to internally threaded pipe of designation M30. Protection class IP65. Mechanical resistance IK09 (Polycarbonate diffuser). Pure polyester powder coated graphite grey / anthracite grey / jet black. Available colour temperature 3000K / 4000K / 5700K as per TMC Enginaer and as per application. Colour rendering indax (CRI)>70. Standard Deviation colour matching 3 MacAdam. Led module with expected service life of at least 72,O00 operating hours. Driver shall be of K-lite/ Philips/ Invetronics and are a Fixed constant current driver with an output current of 1200 MA, 48Vdc ,58W. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency > 859'», power factor > 0.95, THD < 10%, internal Surge Protection 6KV of the driver. Input Rated Voltage is 240V,50-60 Hz. Input operating voltage range of 100-300 Vac. The driver shall have short circuit protection with automatic restart, Overvoltage Protection, thermal protection and No load protection. Led Source Shall be of Nichia / Lumiled/ cree or Equivalent Make and shall be of standard deviation colour matching to 3 Step Mcadam. External SPD of 10KV shall be provided along with the fixture. Luminaire dimension : 425mm diameter x height 407 mm / 437mm. BIS Certified 1br Luminaire

Supplying & erecting Decorative light pole of height 4 m high (clear height) with decorative double bracket made out MS Pipe as per IS1161:1998 .The Pole will have provision for in built junction box weather proof flush door & locking arrangement for housing at bottom of the dia. of the pole shall be 140 mm & top section dia of 76 mm and base plate dimensions 250x250x10 mm thick and bottom and middle pipe of the pole shall be provided with cast iron /Aluminium embellishment to add aesthetic on the pole with the help of grub screw .The body of the decorative pole and bracket will be duly painted in U.V ray resistant PU coating in approved colour shade. The coating should have a DFT of 50 microns .The Tentative shape is enclosed herewith .The final design shall be got approved from Engineer in charge.

Supplying & erecting Decorative light pole of height 4 m high (clear height) with decorative Single bracket made out MS Pipe as per IS1161:1998 .The Pole will have provision for in built junction box weather proof flush door & locking arrangement for housing at bottom of the dia. of the pole shall be 140 mm & top section dia of 76 mm and base plate dimensions 250x250x10 mm thick and bottom and middle pipe of the pole shall be provided with cast iron /Aluminium embellishment to add aesthetic on the pole with the help of grub screw .The body of the decorative pole and bracket will be duly painted in U.V ray resistant PU coating in approved colour shade. The coating should have a DFT of 50 microns .The Tentative shape is enclosed herewith .The final design shall be got approved from Engineer in charge.

Supply of decorative luminaire made of spun aluminium body with pressure die-cast heat management (PDCHM) and the IP65 optical compartment with high power LED/s is comprised of a deep drawn chemically polished and co-extruded, thermoformed polycarbonate protector stabilized agent UV rays suitable for 45W LED. Fitting should be post top mounting type decorative fixture. fitting should have decorative elements to be placed on top of the fixture for aesthetic purpose. Fitting should have inbuilt driver with efficiency >0.9 and having surge protection device of 4KVA and external surge protection device of 10KVA, colour temperature 3000K / 4000K / 5700K Natural day light LED.LED's to be of Osram / Cree / Bridgelux & driver to be of make Philips / fulham / Osram.

Providing & erecting 9 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 155 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL

Supply Installation Testing & commissioning of integral high pressure Die cast/extruded aluminium LED Floodlights luminaire with proper heat dessipation & toughned glass protector or with yellowing injection molded polycarbonate cover having high light transmission index.The LEDs are provided with suitable lens for dispersal for achieving street light optics to ensure uniform light distribution.The LED fixture shall be desighned for at least L70 life of minimum 50,000 burning hours at ambient tempreture not less than 35*C. the system wattage (fixture's total power consumption) should be be 350W. Details as per technical specification attached.

Supply Installation Testing & commissioning of integral high pressure Die cast/extruded aluminium LED Floodlights luminaire with proper heat dessipation & toughned glass protector or with yellowing injection molded polycarbonate cover having high light transmission index.The LEDs are provided with suitable lens for dispersal for achieving street light optics to ensure uniform light distribution.The LED fixture shall be desighned for at least L70 life of minimum 50,000 burning hours at ambient tempreture not less than 35*C. the system wattage (fixture's total power consumption) should be be 200W. Details as per technical specification attached.

SITC of streetlight control panel inclusive of all electrical accessories mentioned in tender document. (with IoT based smart lighting system with 3 nos. of CT for incoming side.

SITC of streetlight control panel inclusive of all electrical accessories mentioned in tender document. With quartz electronic time switch.

Providing PU paint to octagonal poles as required of desired colour duly finished in an approved manner for 7 mtr long pole

Providing PU paint to octagonal poles as required of desired colour duly finished in an approved manner for 9 mtr long pole

Supply and erection of Hot dip galvanised ring for installation of mini high mast suitable for 4 nos of LED Flood lights. The outer dia of the ring shall be 600 mm. The ring shall be of 50 mm dia B class pipe with three supports to sleeve, the sleeve shall be 500 mm length and 4 mm thick duly provision of 4 nos bols and shall be suitable to fit on Octagonal pole of 70 mm AF

Providing PU paint/ Powder coating as required of desired colour duly finished in an approved manner for 600 mm dia. Highmast mini ring.

Providing M20 concrete for resurfacing the road.

Supplying, erecting & marking SPMCB 0.5A to 5A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation, fixing provided nut bolts with the help of template, duly plastered as per design complete (for 3 to 5m octagonal / conical GI pole).

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation, fixing provided nut bolts with the help of template, duly plastered as per design complete (for 6 to 8m octagonal / conical GI pole).

Making M-20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 9m & 10m high octagonal/conical GI pole).

Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable 1100 V, 3 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 70 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Providing & erecting epoxy outdoor / indoor end termination kit for LT XLPE armoured cable 70 to 120 sq mm., with necessary material as per specification No. CB-JT/LT

Supplying, installing and testing pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia. G.I. Rod complete with all accessories of GI materials & recording the results as per specification no. EA-EP

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 4 core 10 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 4 core 16 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Providing & erecting 4 Pole MCCB, 415V, 160A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact. MCCB with phase barriers on both sides, insulation withstand capacity 800V, no line load bias in provided enclosure/panel as per specification no. SW-MCCB

Supplying and erecting extended rotary handle for MCCB with adjustable telescopic rod suitable for up to 250A MCCB.

Supplying and erecting terminal spreaders suitable for 4 pole, upto 250A MCCB (Set of 8)

Supplying and erecting LT CT multifunction DLMS compliance energy meter of accuracy of class 0.5, 3x240V, 50 Hz with optical & RS 232 port,backlit LCD, measures & displays trivector energy, load survey, TOD, tamper detection & logging, power ON /OFF events, instantaneous parameters of rating 1/5 A with display in absence of power complete with zero adjustment & test certificate from manufacturer erected on provided M.S. box and connected to CTs.

Supplying & erecting LED type indicating pilot lamp with LED colours red / yellow / green, 230 / 250V on provided box / panel with necessary material, wiring & connections etc.

Supplying & erecting LED type indicating pilot lamp with LED colour blue, 230 / 250 V on provided box / panel with necessary material, wiring & connections etc.

Supplying and erecting metal work in CRCA sheet including Iron work for supports with fabrication of boxes, panel boards, etc. including cutting, bending, drilling, welding, riveting, treated with anti-rust treatment and duly powder coated or painted with one coat of red lead paint and 2 coats of enamel paint complete

Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Supplying and erecting aluminium strip of required sizes used for earthing or any other purpose with necessary aluminium clamps fixed on wall painted with bituminous paint as per specification no EA-EP. to provide the support for the connectors

Supplying and erecting enamel iron G.I. sheet 1.25mm (18 gauge) caution board of size 200 x 150 mm. as per I.S. 2551 of 1982 in Marathi and Hindi erected at position.

Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking DPMCB 6 A to 32 A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking TPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking TPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 10 ways (10 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection provided on iron/GI frame asper specification no. SW-MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 12 ways/phase (36 poles), with door, 1.2mm thickness surface/flush mounted, IP 43 Protection provided on iron/GI frame (horizontal busbar type) as per specification no. SW-MCBDB.

Supplying, erecting & commissioning 2 pole RCCB 40A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no.SW-RCCB/RCCB

Supplying, fixing and commissioning 2 pole RCBO 32/40A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO

Supplying, installing, testing & commissioning of Garden speaker with frequency response;85 Hz to 20KHz +/-5db,sensitivity-89 db//w/m/ power handling;30w RMS,impedance:8 ohms lastic,coverage pattern 360 deg omni directional,similar to garden speak 50 of Ahuja Audio or its equivalents.

Supplying, installing, testing & commissioning of professional amplifier equivalents to SPA-15000 Ahuja make 1500 watts high power PA Amplifier.

Supplying & erecting junction box for speaker.

S & E Loud Speaker cable 4 core 2.5 sqmm copper multistrand conductor shielded hifi application cable conduit system

Supplying and erecting professional ahuja fmx 106dp with usb & bluetooth aux in mic in

Supply Erection of GI bracket suitable for garden speaker(U-type bracket)

Supplying & erecting SS Rack Enclouse for music system

Supply, installation, testing & commissioning of 4MP IP Dome/Bullet Camera 1/3" CMOS image sensor, Output 4mp (2560X1440) @25/30fps, Max.H265 codec high compression ration, Buit-in IR LED, max IR distance: 30m, H.264 MJPEG, WDR-120dB, SD card slot, Support max.256 GB micro SD card, IP67 protection, Steams capacity 2, Protection IP67, CE,ROHS.

Supplying & erecting 8 TB internal Surveillance HDD suitable for SATA Port of NVR, interface transfer rate 6 GB/S, maximum sustained transfer rate 210 MB/Sec to 213 MB/S. Drive bay supported 08+, Cameras supported up to 64, Cache (MB) 256, Load/Unload Cycle -3000000, Work Load Rating per Year 180TB, MTBF 1000000 Hrs. HTTPS. RoHS, UL, CE certified, duly erected in position in provided NVR as per specification no. CCTV-HDD

Supplying & erecting 32" professional LED Monitor with 1920*1080 (Full HD) Display, suitable for 16 channel NVR and following features Brightness: minimum 250 Cd/m2 Contrast Ratio: minimum 1000:1 Viewing angle: 178/178 deg.Response time: maximum 8 ms Inputs: HDMI, VGA, BNC, USB, Audio In, Built-in speakers maximum 2 W, Suitable to operate on 100-240 V 50 Hz AC supply and 24/7 Duty Cycle duly erected on wall or table top with standard accessories like wall mount stand and wiring connections etc. complete as per specifications no. CCTV-MON

Supplying, installing, testing & commissioning of 32/40 Ch Network Video Recorder (NVR), suitable connect Min. 32 IP Cameras, up to 5 Megapixel Resolution, with HDMI1/VGA1 outputs, provided Atleast one HDMI output of 4K resolution, atleast one VGA output with output up to 1920x1080, Support H.265 or higher, H.264, MJPEG,Supports Redundant Dual Power, Incoming Bandwidth 320 Mbps with minimum 8 SATA ports, ANR Technology, 8 SATA interfaces for 8 HDDs and capacity of each HDD up to 8TB, minimum 02 USB port, Alarm I/O 16/4, RJ-45 10/100/ 1000 Mbps selfadaptive Ethernet interface,support multibrand network Cameras,ONVIF conformance,Multiple network monitoring: Web viewer. support protocol TCP/IP, DHCP, DNS, DDNS, NTP, SADP, SMTP, NFS, iSCSI, UPnP™, HTTPS. RoHS, UL, CE, FCC certified. duly erected in provided U Rack with wiring connections, tagging and programming etc. complete as per specifications no. CCTV-NVR

Supplying and installing FR PVC sheathed HDPE insulated copper cat-6 armoured cable suitable for networking compliant with ANSI/TIA-568.2-D standards as per specification no. WG-ELVC/NC

Supplying, fixing, and configuring 8-ports 1 GE un-managed gigabit PoE switch compliant with IEEE 802.3 standards, min. 120W PoE capacity with 2GE SFP uplink erected in provided rack complete

Supplying and installing FR PVC sheathed HDPE insulated copper cat-6 cable suitable for networking compliant with ANSI/TIA-568.2-D standards in provided conduit/casing-n-capping as per specification no. WG-ELVC/NC

Supplying, installing and testing UTP connector (RJ-45) as per specification no.WG-NAS/UTPC.

Supplying, erecting, testing & commissioning of 1 kVA capacity on line pure sine wave, PWM, IGBT based UPS with 0.8 to unity output pf , single phase input & 1 phase output complete with all protections as per specification no. APUPS (Without batteries)

Supplying and erecting 12 V/65Ah SMF battery with battery terminal wire, duly charged complete with 24 months warranty complete

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, complete.

Supplying and installing PBT loose tube HDPE sheathed armoured single mode optical fiber cable with 6 fiber, core dia 9/125μm (OS1/OS2) 10 GBPS speed compliant to IEC 60793/IEC 60794 standards in provided pipe/trench complete.

SITC 1 Gig port SFP 10 /100/1000 connectivity module (Fiber Optical Transceiver) of fiber link on 4 port poe switch. Shall support distance as required on site.

Supplying and installing Fiber patch cord for jointing fibers with Sc-SC,SCLC Connectors. Allowed Lateral Pressure 100 N/100mm. Round Wire shaped.

Supplying and erecting mains with 3x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable, 1100 V 2 core 10 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating HDMI Extender Over RJ45 Ethernet Cable Cat 6, 60m/200ft complete.

Supplying and fixing 6U wall mount rack (Dimension-DxWxH – 500x550x347 mm) as per specification no. WG-NAS/RAK

Supplying and fixing 9U wall mount rack (Dimension-DxWxH – 500x550x480 mm) as per specification no. WG-NAS/RAK

Supplying and installing bracket for erection of cctv camera on pole

jha p and compony (BID ID -6521633)