CWEK-20/2024-25 PROVN OF DEFI GD HOUSE AND ANCILLARIES AT 2 FOD AT BB CANTT UNDER GE 864 EWS

Amount

Excavation in trenchess n.exc 1.5m wide and n.exc 1.5m in depth for foundation and laying of pipe line and getting out in hard/dense soils etc.complite all as specified and directed by Engr-in Charge.

M&L Plain cement concrete (1:4:8), type D2 (Using 40mm graded aggregate) as in foundation fillng and mass concrete..complite all as specified and directed by Engr-in Charge.

M&L Mild steel TMT bars 10mm dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips.complite all as specified and directed by Engr-in Charge.

M&L Mild steel TMT bars 6 to 8 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips .complite all as specified and directed by Engr-in Charge.

Material and labour for RCC(M25,Design mix) (Using 20mm graded curshed stone aggregate) as in foundation including raft footings, foundation beam, plinth beam, bases of columns tc basement slab under reamed piles and mass concrete.complite all as specified and directed by Engr-in Charge.

Material and labour for RCC(M25,Design mix) (using 20mm graded curshed stone aggregate) as in columns, pillars, piers, posts and struts, .complite all as specified and directed by Engr-in Charge.

Material and labour for RCC(M25,Design mix) (using 20mm graded curshed stone aggregate) as beams, cantilever, bressummers, lintels over 1.5m span .complite all as specified and directed by Engr-in Charge.

M&L for Form work to sides of concrete foundations, footings bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter..complite all as specified and directed by Engr-in Charge.

M&L for Form work to sides of Sqare/rectangular pillar, post, strutts, piers, columns, and stanchions.complite all as specified and directed by Engr-in Charge.

M&L for Form work sides and soffits of roof beams, beam haunchings, girders, breasurers, lintels cantillevers, shelves including supports, overhangs etc and also splays between floors and beams etc.for fair finished to side and soffit of domes, vaults,shell roofs and arch ribs curved in two plane..complite all as specified and directed by Engr-in Charge.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 mtr mean radius, built in cement mortar 1:6 as in manhole, wall, Drain etc complete all as specified and directed by Engineer-in-Charge.

M&L for cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubings or conduit wiring, etc and making good, cutting not exceeding 10cm girthcomplete all as specified and directed by Engineer-in-Charge.

M&L rendering15mm thick plastering in cement mortar 1:6 on fair faces of brick or concrete surface finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L rendering15mm thick plastering in cement mortar 1:4 other than fair faces of brick or concrete wall surface trowelled to finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered wall surfaces and appying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and directed by Engineer-in-Charge

M&L for preparation of newly plastered wall surfaces and appying two coats of Oil bound distemper over a coat of alkali resistant priming paint complete all as specified and directed by Engineer-in-Charge.

S&F roof trusses (framed), trussed, purlins crane grantries, rails and fasternings and heavy bracket framing( Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc of Fe410-W (Gde-E-250)quality A, complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of newly steel surface over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed by Engineer-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour of having tensile strength of 550 mpa asin roof covering/cladding to wall, fixed with tapping screws complete all as specified and directed by Engr-in-charge

S&F for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-charge

S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre with hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed by Engr-in-charge.

Gypsum board 12mm thickin ceiling fixed with screw as per manufacturers instructions complete all as specified and directed by Engr-in-charge.

Returning, filling in, including spreading, levelling, watering & well ramming in layers n. exc 25 cm in soil complete all as specified and directed by Engr-in-charge.

Removing excavated soil n exc. 50m & depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engr-in-charge.

M&L Hard core of gauge n.exc 0.63mm, deposited, spread and levelled in layers n.exc 15 cm thick watered and rammed to ture surface complete all as specified and directed by Engr-in-charge.

M&L 40mm thick PCC 1:2:4, type B1 (20mm graded aggregate) as in floor finishes complete all as specified and directed by Engr-in-charge.

M&L Virified Ceramic tiles 10 mm thick (square/ rectangular) light shade, polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-charge.

M&L Vitrifired ceramic tiles light shade 10mm thick, polished, in pieces of required width cut out of 600mm x 600mm size, in dado/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including10 mm thick Screeding layer in cement mortar 1:4 tiles complete all as specified and directed by Engr-in-charge

M&L Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm, in floor etc, set and jointed neat cement slurry and pointed in white or coloured cement to match and 15mm thick sreed bed or bedding/backing coat in cement morta 1:6 for laying floor finishes complete all as specified and directed by Engr-in-charge.

M/L glazed ceramic coloured tiles, joint free 200x300x7/350x250x7mm thick for work on vertical surfaces such as skirting, dado, set & jointed in cement slurry and pointed in coloured cement to match over 10mm thick plastring in CM(1:3) complete all as specified and directed by Engr-in-charge.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube suppling and fixing in opening as per specification and drawingcomplete all as specified and directed by Engr-in-charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rail MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitabele PVC sheet beading and joined together with solvent cement suppling and fixing in the frame at site as per specification and drawing, complete all as specified and directed by Engr-in-charge.

S&F butt hinges, medium weight cold rolled, mild steel of size 75 mm complete all as specified and directed by Engr-in-charge.

S&F for aluminium, anodised, barrel tower bolts of extruded setion of size 100 mm,and fixed complete all as specified and directed by Engr-in-charge.

S&F 100 mm aluminum alloy handles, fabricated type, anodised complete all as specified and directed by Engr-in-charge.

S&F 1000 litres capacity rotational moulded polye-thylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including brass float valve all as specified in SSR Part I complete all as specified and directed by Engr-in-charge.

S&F steel water tubing 15 mm dia 'medium grade', galvanised, with all fitting and fixed complete to walls and ceillings or laid in floorscomplete all as specified and directed by Engr-in-charge.

S&F steel water tubing 20mm dia 'medium grade', galvanised, with all fitting and fixed complete to walls and ceillings or laid in floors, complete all as specified and directed by Engr-in-charge.

Supply and fixing vitreous china wash hand basin white flat back of size 550x400mm with padestal including CI brackets embedded in wall in CM 1:4, PVC waste pipe and chromium plated waste coupling, etc complete all as specified and directed by Engr-in-charge.

S&F 15mm bore Brass CP wall mixer for mixing hot & cold water (for bathroom) screwed down for iron pipe and fixed complete all as specified and directed by Engr-in-charge.

S&F 15mm bore Brass CP mixer for mixing hot & cold water (for WHB) screwed down for iron pipe and fixed complete all as specified and directed by Engr-in-charge.

S&F Aluminum anodised tubular towel rail 20mm dia incl side brackets fixed to wall 60cm long complete all as specified and directed.

S&F glass shelf assembly consisting of glass shelf, 60cm long and 12 cm wide with CP bracket and guard railing fixed in repair complete all as specified and directed by Engr-in-charge.

S&F CP Soap dish, any type fixed to plug with chromium plated brass screwscomplete all as specified and directed by Engr-in-charge.

S&F Corner Glass shelf 300 x 300 mm (Big) , 225 x 225 mm (medium) & 150 x 150 mm (small) three set, complete all as specified and directed by Engr-in-charge.

S&F CP grating suitable for 75/100 mm bore floor trap and fixed with white cement, complete all as specified and directed by Engr-in-charge.

S&F in repairs health faucet for EWC fixed in repair complete all as specified and directed by Engr-in-charge.

S&F in repair 20 mm dia decorative powder coated drapry curtain rods of with bright finish,including decorative side domes, brackets and a minimum of 8 Nos curtain rings in per RM of length complete all as specified and directed by Engr-in-charge.

S&F 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including Flush pipe of polyethylene of low or high density or PVC. 32 mm dia complete all as specified and directed by Engr-in-charge.

S&F Vitreous China wash down water closet pan (pedestal pattern), white excluding fixing bolts, flushing cistern and flush pipe) including jet spray, PVC seat cover (closed pattern), connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc complete all as specified and directed by Engr-in-charge.

S&F Bib tap cast copper alloy chromium plated fancy type long body with crutch or butterfly handle, screwed for iron pipe or for brass ferrule of bore 15mm complete all as specified and directed by Engr-in-charge.

S&F Brass CP shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or unioncomplete all as specified and directed by Engr-in-charge.

S&F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed by Engr-in-charge.

S&F Angle stop valve 15 mm dia of PTMT any colour high pressure screwed for iron pipe and fixed.(Minimum weight 15mm-90gms) complete all as specified and directed by Engr-in-charge.

S&F PVC connections 600 mm long and 15mm dia with PTMT nuts and PVC washers on both ends, complete all as specified and directed by Engr-in-charge.

S&F 75 mm dia PVC (SWR) pipes including necessary fittings, single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engr-in-charge.

S&F 110 mm dia PVC (SWR) pipes including necessary fittings, single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engr-in-charge.

S&F PVC (SWR) branch piece, double (double Y), equal or unequal 110mm dia with access doorcomplete all as specified and directed by Engr-in-charge.

S&F PVC (SWR) branch piece, double (double Y), equal or unequal 75 mm dia with access door complete all as specified and directed by Engr-in-charge.

S&F 110mm dia PVC (SWR) Junction single ,(single T) equal or unequal complete all as specified and directed by Engr-in-charge.

S&F 75 mm dia PVC (SWR) Junction single ,(single T) equal or unequal complete all as specified and directed by Engr-in-charge.

M&L PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement complete all as specified and directed by Engr-in-charge.

S&F Mild steel conforming to Fe-290-0 GdeE-165 complete. in framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars,frame work for chowkhat of iron doors & windows including holdfast, ladders; railings frame work of water tanks and similar work welded complete all as specified and directed by Engr-in-charge.

S&F Factory made Steel door including all fitting projecting type hinges with steel handle, and steel peg stay, with glazing bars, devetailed or welded complete all as specified and directed by Engr-in-charge.

S&F Factory made Steel windows,ventilator with side hung shutters including all fitting projecting type hinges with steel handle, and steel peg stay, with glazing (3mm ordinary quality sheet glass) ,devetailed or welded complete all as specified and directed by Engr-in-charge.

M&L for 35mm thick 2nd class hard wood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln easoned and chemically pressure treated complete all as specified and directed by Engr-in-charge.

S&F 30mm thick 2nd class hardwood factory made glazed and skeleton door/window shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed by Engr-in-charge.

S&F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples etc complete all as specified and directed by Engr-in-charge.

S&F 150 mm size aluminium anodised barrel tower bolts of extruded sections complete all as specified and directed by Engr-in-charge.

S & F stainless steel butt hinges medium weight 100 mm size etc complete all as specified and directed by Engr-in-charge.

S&F 250mm aluminium alloy, anodised, sliding door bolt with hasp, staple & fixed clips of sheet, cast or extruded section & fixed bolts & sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed by Engr-in-charge.

S&F 150 mm size extruded aluminium handles fabricated type, anodised complete all as specified and directed by Engr-in-charge.

S&F mild steel 300mm size ordinary rat tail pattern springs for door including rollers and roller plate complete all as specified and directed by Engr-in-charge.

M&L for Preparation new wooden surfaces and applying two coat of synthetic enamel paint over one coat of pink primer surface of any description not other wise described over 10 cm width or girthcomplete all as specified and directed by Engr-in-charge.

M&L for 75mm thick PCC 1:3:6 type C-1, as in plinth protection/PCC path and paving, laid in panels of area not exceeding 2.00 sqm with 6mm wide joints filled with mastic (using bitumen and sand mixture applied hot in the ratio of 1:3 by weight) formed at the end of each panel and change in direction of plinth protection/PCC Path and paving and finishing the top surface even and smooth without using extra cementcomplete all as specified and directed by Engr-in-charge.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth for foundation, shafts, cesspits, manhole, pier holes etc, and getting out in any type of soil complete all as specified and directed by Engr-in-charge.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parpetns and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like incl weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed by Engr-in-charge.

M&L for PCC 1:3:6 type C-2 using 40mm graded aggregate, 100mm thick as in sub base complete all as specified and directed by Engr-in-charge.

Removing excavated material n exc 250 m and n exc 500 m and depositing where directed a a level n exc 1.5 m above the starting point, complete all as specified and directed by Engineer-in-Charge.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/ loose soil complete all as specified and directed by Engr-in-charge.

M&L for PCC 1:4:8 type D-2 using 40mm graded aggregate 100mm thick as in sub base complete all as specified and directed by Engr-in-charge.

M&L for 60mm thick Machine pressed factory made precast rubber moulded cement concrete interlocking paver blocks with grey cement and no pigment of grade M-35 of any size & shape confirming to IS 15658-2006 as directed & incl 50mm thick sand cushion complete all as specified and directed by Engr-in-charge.

M&L cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in surface channels and drains complete all as specified and directed by Engr-in-charge.

M&L for 15mm thick rendering in CM 1:4 on fair face of brick work concrete surface in manhole, finished even and smooth without using extra cement, with using water proofing compound @ 3% by weight of cement, complete all as specified and directed by Engineer-in-Charge. Note :- WPC shall be measured and paid separately under respective item.

M&L for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in coping etc. including weathering, slightly rounded or chamfered angle and throating, complete all as specified and directed by Engineer-in-Charge.

Supply only integral water proofing compound and used as per manufacturer's instructions complete all as specified and directed by Engr-in-charge.

M&L for cement concrete 1:3:6, type C-2 (using 40mm graded crushed stone aggregates) as in concrete bed to drain pipes 200 mm bore including packing under and haunching against the sides of pipe after they are laid and tested, complete all as specified and directed by Engineer-in-Charge.

M&L for 200 mm bore RCC (Reinforced cement concrete) pipes, Class NP-3 with collar, laid in trenches and jointed, complete all specified and directed by Engineer-in-Charge.

M&L for cutting into existing manholes for connecting new drains of 150mm bore (internal bore) and making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or ¾ section) in cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregates), smooth finished and reforming benching as required, complete all as specified and directed by Engineer-in-Charge.

M&L for RCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in cover slab for manhole etc. including necessary formwork, complete all as specified and directed by Engineer-in-Charge.

S&F for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either holdfast, hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing completeall as specified and directed.

M&L 18-20mm thick granite (of any type) on vertical surfaces machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admisxture of pigment to match the shade of granite stone inccluding graindiong, polishing complete over 10mm thick plaster in cement mortor 1:3 complete all as specified and directed by Engr-in-charge.

Point wiring with 1.5 sqmm, copper conductor FRLS (standard) PVC insulated ISI marked unsheathed in and including PVC conduit medium grade ISI marked not less than 20mm dia with all fittings/accessories and also including PVC ISI marked unsheathed 1.5 sqmm copper multi starandard cable FRLS as earth wireconnected to common earth dolly and MS sunk pressed mild steel terminal box suitable for accessories, junctioin box, other boxes made from 1.6mm thick steel sheet of suitable size for mounting of switches, fan regulatores for following :-

(a) One light/fan point controlled by one way switch 5 Amp

(b) One 3 pin socket outlet, 5 Amps independent

Point wiring with 2.5 sqmm, copper conductor FRLS (standard) PVC insulated ISI marked unsheathed in and including PVC conduit medium grade ISI marked not less than 20mm dia with all fittings/accessories and also including PVC ISI marked unsheathed 2.5 sqmm copper multi starandard cable FRLS as earth wireconnected to common earth dolly and MS sunk pressed mild steel terminal box suitable for accessories, junctioin box, other boxes made from 2mm thick MS sheet complete all as specified and directed by Engr-in-charge.

All as per sel item No. 97 above but One 3 pin socket outlet, 15 Amps, independent, with cables 4 sq. mm size complete all as specified and directed by Engr-in-charge.

S&F Single pole and neutral Sheet metal enclosure with a two pin and earth plug and socket complete with one single pole MCB 20Amps complete all as specified and directed by Engr-in-charge.

S&F Modular 6 Amps 230 Volts one way switch, 1 module complete all as specified and directed by Engr-in-charge.

S&F Modular socket 6 Amps AC 230 Volts 2/3 pin combined 2 module complete all as specified and directed by Engr-in-charge.

S&F Modular 16 Amps 230 Volts one way switch, 1 module complete all as specified and directed by Engr-in-charge.

S&F Modular socket 6/16 Amps AC 230 Volts 2/3 pin combined 2 module complete all as specified and directed by Engr-in-charge.

S&F Ceiling rose 3 phase/PVC/polycarbonate , isolated bodycomplete all as specified and directed by Engr-in-charge.

S&F White cover plate with frame,1 modulecomplete all as specified and directed by Engr-in-charge.

S&F White cover plate with frame,3 module complete all as specified and directed by Engr-in-charge.

S&F White cover plate with frame,4 module complete all as specified and directed by Engr-in-charge.

S&F White cover plate with frame,6 module complete all as specified and directed by Engr-in-charge.

S&F White cover plate with frame 8 moudule complete all as specified and directed by Engr-in-charge.

S&F Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings complete all as specified and directed by Engr-in-charge.

S & F stepped type electronic fan regulator ,120 w-2 module type as reqd complete all as specified and directed by Engr-in-charge.

Submain wiring alongwith earth wire with 2 x6 sqmm and 1 x4 sqmm earth wire fo FRLS PVC insulated unsheathed copper strandard conductor, single core cable in PVC recessed conduit including PVC conduit medium grade and fittings of size not less than 25 mm dia, wall thickness not less than 1.8 mmcomplete all as specified and directed by Engr-in-charge. Note :- 2 x 6 sqmm + 1 x 6 sqmm including PVC conduite shall be measured as one RM

S&F Light grade galvanised steel tubing of nominal dia 40 mm fittings laid in building, trench etc complete all as specified and directed by Engr-in-charge.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed by Engr-in-charge.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed by Engr-in-charge.

Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder includingLED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr-in-charge.

Supply and fixing LED lights fittingRecessed mounted 2"x2" LED luminaries 42/36 Watt LED 230 Volts panel celesta fittings suitable for armstrong grid ceiling with driver holder and LED lamp suitable for roof ceiling complete all as specified and directed by Engr-in-charge.

Supply and fixing LED street light fitting 35/40Watt 230 V AC outdoor type with high pressure diecast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protectioncomplete all as specified and directed by Engr-in-charge.

S&F Water heater storage type (Gyeser) of 25 Ltrs capacity white/ivory colour, 5 star complete including grouting of bolts for fixing of gyesers vertically electric and water supply connections complete all as specified and directed by Engr-in-charge.

S&F Sheet metal enclosure TPN factory made IP 43 protection double door DB,s 415 V, Triple pole and neutral 6 way with 200 Amp rated bus bar, complete all as specified and directed by Engr-in-charge.

Earthing complete with galvanised steel earth plate electrode of size 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or 4 mm dia GI earth wirel , procteded by GI medium grade pipe 15 mm bore upto 7.5 mtr including chamber of concrete pit in pcc (1:2:4) type B1 using 20 mm graded stone agg. with 40 mm thick cover of RCC 1:2:4 with XPM (weight not less than 4Kg/SqM) and frame of cover 25 x 25 x 3 mm with lungs 2 Nos and with 6 mm dia MS bar grade to shape, GI light grade 20mm bore pipe for watering at bottom 1.75 Mtr long based on top edge of earth plate salt and charcoal filling test point made out of bornze/gun metal fixing arrangement, funnel, wire mess and earth work in hard/dense soil, returning filling and surplus soil to a distance not exceeding 50 Mtr all as per Plate N0 3 of SSR-2010 Part-I and connected to earthing test point all as specified or indicated including testing on complete all as specified and directed by Engr-in-charge. Note :- quoted rate of earthing shall be deemed to include cost of pipe,galvanised wire 4 mm dia and protection pipe 15 mm medium grade, GI light grade 20 mm bore watering pipe.

M&L for Removing excavated material in soils exc.500m and deposting where directed at a level n exc.1.5m above the starting point complete all as specified and directed by Engr-in-charge.

Supply and laying brick common burnt sub class B old size for protection of cable laid in trenches laid flat for underground cable complete all as specified and directed by Engr-in-charge.

Material and labour for sand cushioning with a layer of fine sand 8 cm thick before laying of cable and 15 cm thick after laying of cable in trenches for cable protection complete all as specified and directed by Engr-in-charge. Note:- Measurement shall be taken only after punning down sand cushioning.

Material and labour for GI tubing light grade including all fittings such as elbow, bends, clamps including nut and bolts for cable protection along poles, wall surface, under ground or road crossing etc complete all as specified and directed by Engr-in-charge of 40mm bore.

Supply, laying , jointing and testing undergroung LT cable XLPE insulated heavy duty, GI steel or wire armoured, PVC sheathed multistranded,1100 Volts grade, of cross sectional area 50 sqmm 3.5 core with aluminium conductor as per IS 7098 (Part-I) along with suitable size with aluminium cable lugs (bottle neck /eye let/ ring type as per ground requirement) and cable gland joint etc. complete all as specified and directed by Engr-in-charge.

Supply, laying , jointing and testing undergroung LT cable XLPE insulated heavy duty, GI steel or wire armoured, PVC sheathed multistranded,1100 Volts grade, of cross sectional area 35 sqmm 3.5 core with aluminium conductor as per IS 7098 (Part-I) along with suitable size with aluminium cable lugs (bottle neck /eye let/ ring type as per ground requirement) and cable gland joint etc. complete all as specified and directed by Engr-in-charge.

Supply, laying , jointing and testing undergroung LT cable XLPE insulated heavy duty, GI steel or wire armoured, PVC sheathed multistranded,1100 Volts grade, of cross sectional area 10sqmm 4 core with aluminium conductor as per IS 7098 (Part-I) along with suitable size with aluminium cable lugs (bottle neck /eye let/ ring type as per ground requirement) and cable gland joint etc. complete all as specified and directed by Engr-in-charge.

Supply and fixing Street light bracket 1.5 Mtr long made out of 40mm dia GI pipe light grade bend to shape welding etc and fixing on existing LT pole with 40 x 6mm flat iron MS clamps including necessary nuts, bolts and washers etc and including painting two coats of synthetic enamel paint over a coat of red oxide primercomplete all as specified and directed by Engr-in-charge.

Supply and fixing LED 35 watt pressure dia cast alumunium alloy for housing ( heat sink) for effective thermal management sturdiness, excellent corriosion resistance long life and photobioligically safe LED's, No harmful UV & IR rediatins , instant light with low running temperature, operating temperature (-10ºc) to (+50ºc) with system lumen >/110 Lm/W high efficiency long life LED made with SMD LED package mounted MCPCB . Powered with integral Electric LED driver (SMPS based) over voltage protection , surge voltage protection 10KV with SPD & other safety as per IS 15885 Part-II Sec 13 complete all as specified and directed by Engr-in-charge. Makes : Philips, Havells, GE, Crompton

Material and labour for junction box pole mounted of size 230 x 170 x 110mm made out of engineering plastic comprising 60 Amps, 4 pole aluminium bus bar mounted on DMC insulator, 1 No SP MCB 6 Amps, 10 KA, junction box should be mounted on pole with MS flat iron of sizes 40mm x 6mm including nuts, bolts and washers complete all as specified and directed by Engr-in-charge. Note: Quoted rates shall be deemed to be inclusive of 1.5 sqmm 3 core flexible copper cable from junction box to street light as per site requirement.

Supply and fix post top lantern light fitting LED Type for 40 Watt 230 volts AC Outdoor type with decorative post top for360 degree indirect light IP 65 protection with impact and corrosion resistant complete With all driver and lamp complete all as specified and directed by Engr-in-charge.

Earthing complete with galvanised steel earth plate electrode of size 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth strip 25x4 mm by means of bolts nuts check nuts & washers of galvanized iron or 4 mm dia GI earth wirel , procteded by GI medium grade pipe 15 mm bore upto 7.5 mtr including chamber of concrete pit in pcc (1:2:4) type B1 using 20 mm graded stone agg. with 40 mm thick cover of RCC 1:2:4 with XPM (weight not less than 4Kg/SqM) and frame of cover 25 x 25 x 3 mm with lungs 2 Nos and with 6 mm dia MS bar grade to shape, GI light grade 20mm bore pipe for watering at bottom 1.75 Mtr long based on top edge of earth plate salt and charcoal filling test point made out of bornze/gun metal fixing arrangement, funnel, wire mess and earth work in hard/dense soil, returning filling and surplus soil to a distance not exceeding 50 Mtr all as per Plate N0 3 of SSR-2010 Part-I and connected to earthing test point all as specified or indicated including testing on complete all as specified and directed by Engr-in-charge. Note :- quoted rate of earthing shall be deemed to include cost of pipe,galvanised wire 4 mm dia and protection pipe 15 mm medium grade, GI light grade 20 mm bore watering pipe.

Galvanised Iron water tubing (ISI marked) 50mm bore, (Medium grade) with and including all fittings (ISI marked) Such as sockets, bends, elbows, unions, tees, diminishing pieces etc laid in trenchescomplete all as specified and directed by Engr-in-charge.

Galvanised Iron water tubing (ISI marked) 25mm bore, (Medium grade) with and including all fittings (ISI marked) Such as sockets, bends, elbows, unions, tees, diminishing pieces etc laid in trenches complete all as specified and directed by Engr-in-charge.

Galvanised Iron water tubing (ISI marked) 20mm bore, (Medium grade) with and including all fittings (ISI marked) Such as sockets, bends, elbows, unions, tees, diminishing pieces etc laid in trenchescomplete all as specified and directed by Engr-in-charge.

Stop valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handdle,screwed both ends suitable for 50 mm bore iron pipe or for unions and fixed complete all as specified and directed by Engr-in-charge.

Stop valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handdle,screwed both ends suitable for 25mm bore iron pipe or for unions and fixed complete all as specified and directed by Engr-in-charge.

Stop valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handdle,screwed both ends suitable for 20mm bore iron pipe or for unions and fixed complete all as specified and directed by Engr-in-charge.

Lagging to pipes used in water supply or plumbing all round with, 25mm thick bounded mineral wool performed 'SNAPON' pipe section of density 144Kg/cum conforming to Is9842 on pipe of internal dia 20mm with chicken mesh wire netting 25 gauge, 20mm mesh with 0.01mm aluminium foil for exposed pipe, complete all as specified and directed by Engr-in-charge.

Construction of valve pit of size 60cm x 60cm x 60cm internal dimensions, brick construction, including all necessary excavation and earth work in hard/dense soil, returning, filling in disposal of surplus soil of a distance not exceeding 50 M and depositing where directed PCC in foundation of the Mix (1:4:8) type D2 (using 40mm graded crushed aggregate) brick masonry in cement mortar (1:4) rendering 12mm thick in cement mortar (1:4) internally finished even and fair and pointing flush externally as per work proceeding in the same mortar, mild steel 50X6 mm frame MS sheet cover of 3.15mm thick with handle and locking arrangement, painting all the exposed MS work with two coat of synthetic enamel paint over a coat of red oxide primer and painting all the MS embedded in PCC with two coats of black bituminous paintcomplete all as specified and directed by Engr-in-charge. and shown on drawing.

M/S Vivek Gupta and Co

M/S Tajamul Ah Buchh

AHMED CONSTRUCTIONS AND INFRA PVT LTD