Construction of New Additional Building in Government Hospital at Kavindapadi in Erode District

Amount

Dismantling clearing away the damaged Pressed tiles & weathering course and carefully stacking materials useful for reuse etc, as directed by the departmental officers as per standard specification.

Dismantling clearing away the damaged Reinforced Cement Concrete of any thickness and carefully stacking materials useful for reuse etc, as directed by the departmental officers as per standard specification.

Dismantiling clearing away and carefully stacking materials for reuse of damaged Brick / stone masonry in Cement mortar walls under 3m high of any thickness of wall including clearing the debris ete., complete complying with standard specification and as directed by the departmental officers.

Dismantling clearing away the damaged Doors & windows including removal of frames, hinges and fastenings of any thickness and carefully stacking materials useful for reuse etc., complete and as directed.

Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary refilling the sides of the foundation with excavated soil other then sand in layers of 15cm thick well ramed and compacted, depositing the surplus excavated soil within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

upto 2.00 m

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers

Cement Concrete 1:5:10 (One Cement, Five M-sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification

Filling in basement with CONVEYED GRAVEL with lead of 5 km (other than sand) in layers of not more than 15cm thick, well rammed, watered and consolidated, etc., complete.complying with standard specification

Brick Work in cement mortar 1:6 (one cement and six M-sand) using Fly Ash Bricks of size 230 x 110 x 70mm for the following including curing etc., complete complying with std. specifications

In Foundation and Basement

In Ground Floor

In First Floor

Brick Work in cement mortar 1:5 (one cement and six M-sand) using Fly Ash Bricks of size 230 x 110 x 70mm for the following including curing etc., complete complying with std. specifications

In Foundation and Basement

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc. with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete

Providing and laying in position, Standardised Concrete Mix M-20 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/mᶾ and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers.

In Foundation and Basement

In Ground Floor

In First Floor

Cement Concrete 1:3:6 (One Cement, Three M-sand and Six hard broken stone jelly) using 40mm size hard broken stone jelly for dummy columns, excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete. (Reinforced Cement Concrete 1:2:4 for slab to be extended upto top of splashing with pressed tiles and future extension rods to be embedded in CC 1:3:6 (One Cement, Three M-Sand and Six hard broken stone jelly). Dummy columns should be at least 1 metre height)

In First Floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Cement Concrete 1:5:10 (One cement, Five M-sand and Ten hard broken stone) using 40 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

In Ground Floor

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three M-Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Brick partition walls of 11.00cm Thick thickness using Fly Ash Bricks of size 230 x 110 x 70mm in Cement Mortar 1:3 (One Cement and Three M-Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

In Ground Floor

Providing Granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (One Cement, Two M-sand and Four Hard Broken Stone jelly) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers.

25mm Thick

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three M-sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification

Providing full nosing to the steps or platforms to the Granite slab of 20mm thick including neat finishing, polishing, cost of powder, tools etc as directed by the departmental officers

Paving the floor with best quality Double charged Vertified tiles 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three M-sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification.

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three M-sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor Self design Joint free Rectified tiles of size 305 x 305 x 8mm laid over 20mm thick in cement mortar 1:3 (one cement and three M- sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointed with the Epoxy chemical filling and necessary spacer etc, complete complying with standard specification. ( The make and brand of the tiles should be Johnson / Kajaria / Somany / Nitco / RAK of Equivalent which has shall be got approved by the Executive Engineer before use on work)

Dadooing the walls with best quality and approved Joint free Digital printed Ceramic tiles of size 600mmx300mmx10mm and set in cement mortar 1:2 (one cement and two M-sand) and pointing with colour cement neatly in all floors etc., complete as directed by the departmental officers complying with standard specification.(The tiles should be got approved by the Executive Engineer before use on work)

Paving the floor with best quality TACTILE PAVER type of new tek BT yellow colour ceramic tiles of size 305 x 305 x 15 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M-Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Casting and fixing of R.C.C. PRECAST SLABS of 75mm thickness in cement concrete 1:2:4 (One cement, Two M-sand and Four HBGS) using 20mm gauge hard broken granite stone metal excluding cost of reinforcement grill in position but including cost of moulding and plastering the top side with cement morotr 1:3 (One cement and three P-sand) 10mm thick curing, finishing, etc., complete. 75mm thick .

Stainless Steel (Salem Stainless Steel) Door Frame (Box Section using Stainless Steel Plate 304L Grade of 1.6mm thick) of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel hold fast etc., including rigid butt joint, nut and bolt assembly with nylon inserts not to be weldedd with special purpose hardware preecleaned including phosphating as per I.S.I. with rust preventive primer and ready to assemble condition for easy installation at site including dismantling making necessary chippings and holes in RCC columns, beams, masonry etc., wherver necessary with power drill to the extent required and redoing the same to the original condition after fixing etc., complete with all accessories such as suppling and fixing holdfasts, plastic bush, inssert receiver, rubber bottom, shock absorbers etc., complete as directed by the departmental officers, in all floors.

Supplying and fixing following Ornamental Teakwood entrance door as per the drawings and designs approved by the departmental officers. The outer frame of the door is 150mmx100mm teakwood scantling. The main door shutter opening size is 2.40mx2.40m.The main door should be double leaves and each door shutter fully panelled, the bottom rails are of size 200x50mm.Middle, top and side rails size of 150x150mm with corner designed beeding works. The outer frames are designed with border works on entrance side. The cost includes all kind of furniture fittings such as brass aldrops, brass tower bolt, brass hinges, brass door stopper, brass handles, all the members are finished with two coats of melamine polish with outer priming coat. (Quality of all furniture fittings should be got approved by the Executive Engineer before use).

Supplying and fixing Solid core Particle board flush shutter of nominal thick of 35 mm with Teak ply on both sides and with T.W. lipping alround conforming to IS 2302 including supplying and fixing cost of wind appliances and furniture fittings such as 1no .300 x 12 mm aluminium tower bolt 2 nos. 200x12 mm aluminium tower bolts 1no. 250 x 16 mm aluminium aldrops, 2 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete as directed by the departmental officers.

a) Single leaf shutter

a) Double leaf shutter

Providing and fixing of 1.2mm thick Lead Lining Door for X-Ray Rooms, Scanning Rooms with Mild Steel Door Frames 105mm x 57mm X 18 G and 12 G x 50mm Shutter made of GI with PWG finish and honey wool insulations with SS 101mm x 75mm x 3mm SS 304 Ball Bearings Butt Hinges, Mortice Sash Lock ML 100A,50mm BS, 85mm centre, CL 207 : Key & Knob 70mm, 5 Pin Cylinder with Handle SS Finish (Dorma Make), Heavy Duty Door Closer, Frames fixed wih walls using Mortice Sash Lock ML 100A, 50mm BS, 85mm centre CL207: Key & Knob 70mm, 5 Pin Cylinder with Handle SS Finish (Dorma Make) all neccesary accessories and fittings as per the required and as per the approval for the Department Officer

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and fixing of WPC ( Wood polymer Composite ) frame extruded with size 75mm x 50mm. The single core door made of rigid WPC compound with minimum bulk density of 900 Kg/Cub,Mt. & shore hardness of 55. Supplying and fixing of QUTE WPC door shutter, extruded as a single core board with rigid WPC compound with the thickness of 25mm (+/-1mm & minimum bulk density of 550 Kg/Cub,Mt. & shore hardness of 55. for the aesthetic appearance, the door shall be a printed digitally on one side of the shutter and the design is desided by the Engineer in Charge of the department. The WPC door shall be fixed on to the WPC frame with 3 Nos of 5" SS Hinges and the door shall have 2 tower bolt on oneside and 1 tower bolt or aldrop on other side for locking system and 2 numbers of handle on the either side of the door shutter, all made of aluminium.

Supply & fixing of WPC door shutter, extruded as a single core board with rigid WPC compound with the thickness of 25mm (+/- 1mm) & minimum Bulk Density of 550 KG/ Cub.Mt. & shore hardness of 55. The door shall be a plain matt board as decided by the Engineer in-Charge of the department. The WPC door shall be fixed onto the Aluminium “G” type channel with Wheel and the door shall have 2 Hooks in SS, 2 Handles 4” in SS.(Sliding door)

Manufacturing supplying and fixing of single leaf steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. IA tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

Supplying and fixing colour galvalume sheet roof of 0.47mm thickand steel tubular box section of 100x50x3mm of 1meter interval including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

Supplying fabricating,erecting and fixing Hilux (or) Equivalent Board False Ceiling upto a ceiling height of 4.5m using perforated sheets ( 10mm thick ) etc,complete

Supplying, and fixing M.S. GRILLS for open courtyard grill, grill work to doors, windows and ventilators etc, using necessary flats for inner and outer members which should be fixed or welded to masonry or column including necessary dismantling or making holes and redoing the same to original condition as directed by the departmental officers inclusive of cost of providing one coat of best quality red oxide primer completre complying with standard specifications.

Plastering with Cement Mortar 1:5 (One cement and Five P-sand), 12mm thick mixed with Bonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three P-Sand) 10mm thick mixed with Bonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three P-sand), 12mm thick mixed withBonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing in all floors including curing etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and painting the walls with two coats of Wall putty as instructed by the departmental officers including preparation of surface curing etc., as per standard specification. (The Wall putty shall be got approved by the Executive Engineer before use of work).

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification

Painting the wall two coats with approved weather proof Exterior Emulsion paint over one primer coat of over cement plastered wall surface ect., complete complying with standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position best approved of BIS quality 110 mm dia PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.(One floor)

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications.

160mm dia PVC soil / waste pipe

110mm dia PVC soil / waste pipe

75mm dia PVC soil / waste pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

110mm dia PVC Elbow

75mm dia PVC Elbow

110mm dia PVC Elbow with Door

75mm dia PVC Elbow with Door

110mm dia PVC Tee

110mm dia PVC Y with Double door

110mm dia PVC Y with Single door

110mm dia PVC Vent Cowl

Supplying, laying and jointing upvc pipes of Below Ground Level upvc (Un-Plasticized Polyvinyl Chloride) Pipe (Higher pressure rating with higher pipe thickness) Standard Dimension Ratio-11 of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing upvc specials using upvc adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.

40mm dia UPVC Pipe

Supplying, laying and jointing upvc pipes of Above Ground Level upvc (Un-Plasticized Polyvinyl Chloride) Pipe (Higher pressure rating with higher pipe thickness) Standard Dimension Ratio-11 of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing upvc specials using upvc adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.

40mm dia UPVC Pipe

32mm dia UPVC Pipe

20mm dia UPVC Pipe

Supplying and fixing in position of the following UPVC SPECIALS (HEAVY TYPE) of approved quality and good variety excluding the fixing charges but including necessary cutting and threading etc., complete.

40 mm x 32 mm

32 mm x 25 mm

20 mm x 15 mm

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements).

40 mm dia G.M. Gate Valve

32 mm dia G.M. Gate Valve

Supplying and fixing in position 15mm dia brass CP screw down tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary.

Supplying and fixing in position 15mm dia brass SS Swan neck tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in position 15mm dia brass SS Elbow Action Tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of with all internal fittings approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two M-sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications.

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers.

Supply and fixing in position of best Indian make white glazed Porcelin Oval shape special type Urinal of best quality and approved make of size 382mm x 398mm x 601mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position best quality Stainless steel sink of 1200 x 550 x 180mm including fixing the sink in position and testing for leakages etc., complete complying with standard specifications

Supplying and fixing in position Indian make Special type mirror of approved quality 1000 x 780 mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supplying and fixing approved best quality Stainless steel Towel rack 600mm long with Lower Hanger including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing best approved best quality brass CP soap tray of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing position PVC Nahani Trap / Floor Trap of of size 100 x 75mm of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of M-sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three M-sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the PVC pipes, etc., complete complying with standard specification.

Supplying and fixing of Health faucet cost of all materials and ISI mark including labour for fixing charges etc., complete

Supplying and fixing PVC ventilating shaft of 110mm dia (having working pressure 4 kg. / sq.cm) with 3 metre height including cost of PVC cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Supplying and fixing of Plastic beading at corners etc., as directed complete complying with standard specification.

Supplying and filling 40mm guauge HBGS stone jelly for dispersion trench including loading conveying and unloading and as directed by the departmental officers etc. complete complying with standard specification.

Supplying and filling 20mm guauge HBGS stone jelly for dispersion trench including loading conveying and unloading and as directed by the departmental officers etc. complete complying with standard specification.

Construction of inspection chamber 0.60 X 0.60 clear sizes including earth work excavation, CC 1:5:10 of 10cm thick and brick work in cement mortar 1:5 [one cement and five M-sand] using best quality of second class Table mould bricks of size 9" X 43/8"X 23/4" with plastering with cement mortar 1:3 [one cement and three P-sand] 12mm thick to inner and outer sides and wearing coat 1:3:6 [one cement, three sand and six aggregate] 15cm thick and covered with precast slab 5cm thick etc., complete complying as directed by the departmental officers as per standard specification.

Supply and erecting of 2.0 HP Submersible Pump supplied with necessary ISI mark including supply and fixing with following accessories for 100 mm dia borewell submersible motor as directed by the departmental Officers a) 2" HP collar - 2 sets, b)Green rubber - 1 Nos, c)End cap - 1 Nos, d)Jet clamp - 1 set, e)11/4"G.I.Bend - 1 No, f)Copper Bolt and Nuts - 4 Nos, g)Copper wire -10Kg, h)2"G.I.Coupling - 2 Nos, i)2"x12"Barrd nipple -2 Nos, j)Shellac bottle -2 Nos

Design,supply&fixing of Gas outlet points:(Self Sealing type-Single/Dinoutlet type) with S type bracket made up of copper and the out let of non-interchangeable for other gas.The outlet points are brazed with brass bracket with self sealing valve(stainless steel) with all accessories and complete set and are converted by plastic cover duly colour coated as per specific gas and button cover etc.,complete as directed by the departmental officers and as per IS Code 12827/1989 & ISO 7396/1987 specification.

Supply and installation of Medical gas copper pipe line arrangement to hang on the wall of socket type connection installation of seamless cleaned and degreased non arsencial phosphorous gas copper pipe line with saddles complete with brazing work including all copper fitting (Tee,Elbow,Reducer,Coupling).The copper pipe lines should be tested suitable for a steam of working pressure of 17.34kg./cm2(17 bar) and confirm to BS 864 standard with specially made for brazed socket type connection.The medical gas copper pipeline should be tested as per standard and commissioning after painting as per international code no IS 2379/1963 Table-V.The pipe lines installed at the various wings and floors etc.,complete as directed by the departmental officers as per IS code 12827/1989&ISO 7396/1987 specification.

15mm dia copper pipe ODx0.9mm thick

10mm dia copper pipe ODx0.9mm thick

Brass Isolation valve. suitable for the copper pipe and should be of non lubricated 90 degree turn lever ball value of RB or Italy or reputed make,connected in line with medical gas pipe line system by using suitable size brass valve adopter union,ferrule,nipple,rubber "O" ring,taption lap and etc.All pipe line regulators shall be capable of controlling pipee line pressure and must compatible with the requirements specified in IS 12827-1989.All valves should be pneumatically tested for twice the working pressure for the gas line as per IS code 12827/1989&ISO 7396/1987 specification.

15mm dia valve

Flow Meter made up of Brass with Humidifier Bottle Flow Meter should be back pressure compressed and should be accurate gas flow measurement with control range 0-13 litres per minute. It should meet strict permission and dumbling standard. The meter body should be made of brass materials. The humidifier bottle should be made of unbreakable polycorbonate material and auto cleavable at 134 degree centigrate. The rate includes flow meter and its accessories (silicon tube with mask). The cost of materials including transport, etc., complete as per standard specification and as directed by the Departmental Officer and as per IS 12827 / 1989 and ISO 7396 / 1987 Specification.

Ward Vaccum Unit with Gauge both mounted on a collection jar of capacity 600 ml and with a wall bracket for mounting it on the wall. The collecion jar should be made of unbreakable polycarbonate materials which is fully auto cleavable at 134 degree centigrade as per standard specification and as directed by the Departmental Officers and as per IS 12827 / 1989 and ISO 7396 / 1987 Specification. The rate includes cost of silicon hose with SS nipple on either side.

Oxygen manifold arrangements of 2 banks x 12 cylinder each wing with semi automatic control panel which includes contact gauge 2 Nos., outlet pressure gauge, brass heavy duty IO x regulator 2 Nos. with suitable adopter, flexible SS Hose. Mainfold shall be of a construction and of a designs and material suitable for the service pressure in accordance with IS 1282-1989. Emergency alarms with illuminating display for low / high pipeline pressure and malfunctioning of system.1) Mainfold top frame with provision for connecting 12 cylinders on right bank and 12 cylinders on left bank with high pressure interconnecting copper tubing, silver brazing, non return valve, fasteners and cylinder spport middle angle frame for claping 2 x 12 cylinders and related fasteners. The O2 manifold should with stand a pressure of 140 kg. / CM2. The installation is commissioned after testing as per standards and painted as per International Code and as directed by the Departmental Officers as per IS Code 12827 / 1989 & ISO 7396 / 1987 Specification.

Supply, installation,testing and commissioning of equivalent to ingersoll rand reciprocating Air cooled type (10 HP+5 HP) rating vaccum pump as per following provisions.As per IS 12827/1987&ISO 7396/1987 specification. a) Vacuum pump-10 HP-1 Set b) Electric Motor-5HP-1No c) DOL Starter OLR-1No d) Vacuum Switch-1No e) Vacuum gauge-1No f) Control frame with fittings-1No g) Suction Scrubber-1No h) V-Belts-1No i) G.I & M.S Fittings-1No j) Brass Fittings-1No k) Exhaust silencer-1No l) Base frame for motor and vacuum pump-1Set m) Pilot line with fittings-1Set,Vacuum Room& Air compressor room inside Vacuum room& Air compressor room inside

Supply, installation,testing and commissioning of compressed air system of reciprocating Oil Free Air Compressor belt driven type air compressor with following provisions. As per IS 12827/1987&ISO 7396/1987 specification. Compressor package consists of the following: a) 10 HP Air Compressor-2Nos b) Electric motor 10HP -2NoS c)Dol Starter-L&T-10HP-2NoS d) Base frame kid(for motor and compressor)-2Set e)Pressure switch-2 NoS f)Pressure Gauge-2NoS g)NRV and Pilot fittings-2NoS h)Delivery tube-2Nos i)Foundation bolts&Anchor fasteners-2Nos j)Belt Guard-2 Nos k)Air Drier 50 to 60 cfm capacity-1 No.Drain ball valve-1No, Air outlet ball valve-1No, Vacuum room& Air compressor room inside Accessories: Non-return valves,Air pressure switch,pressure gauge,Isolation valves,Air filters etc., Inter connecting piping:Mild steel pipe of 2" with fittings.

Supplying and laying polyester, washable and stainfree cloth (Bio-Active fabric washable germ free suitable for dialysis room) curtain system with maximum curtain cloth height 240cm (top 30cm white colour net and 210cm light blue colour as per approval) stitching with stiffener tape, Pleats ironing and laying around each bed using sliding wheels to nylon rollers, nylon axil and tangle free nylon swivel stem with chrome plated steel hook, curtain track should be supported in roof using 20x20mm, 2mm thick sized aluminium tubes same spec with end caps in two sides using all necessary fittings. as per the direction of engineer in charge including conveyance to site laying in line and level sealing all cutting in false ceilling with powder coated MS cup all leads and lifts including all labour charges etc. complete (unpleated length of the cloth measurement will be considered for payment also the bottom and top folding will not be considered in cloth measurement/ supplying and fixing powder coated 20mm dia GI round tube hanging support of required length(app. length 1.10m) one end fixing from slab by using 6mm dia expansion bolt at a distance not more than 2m, c/c down end fixed to powder coated aluminium channel frame 45x20mmx1mm thick section by using SS screw as per the direction of engineer in charge including conveyance.

Providing Anti-Termite Treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 6313 part I to IV in stages to suit the progress of work consist as per the detailed specification as below (Measurements taken for the plinth area for the purpose of payment) including braking of termit mounds, making holes with crow ar, closing the holes after the treatement and including cost of chemicals, labour charges transport and storing etc., complete (The chemical should be got approved by the Executive Engineer before use on works) Stage-1: Spraying anti-termite chemical solution for the foundation before laying concrete in bottom and sides of foundation. Stage-2: Spraying anti-termite chemical solution to the grade beam level, spraying has to done for the grade beam, brick masonry contact with the back fill earth. Stage-3: Spraying anti-termite chemical solution on the sand for the flooring before laying the flooring concrete. This treatment has to be carried out on the sand filling by making holes with crow bar to a depth of 60 cms and at 60cms intervals on both. Stage-4: Spraying anti-termite chemical solution alround building outside by making holes through bar before laying plinth protection and the holes to be closed after the treatment.

star construction (BID ID -1169584)

M MURUGESAN AND CO (BID ID -1168897)