GE 874/EWS-32/2023-24

Amount

BR and EM Portion

Surface excavation n.exc 30cm deep and averaging 15cm deep & getting out in any type of soil.

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation etc n exc 10 sqm on plan and getting out in any type of soil all as specified and directed

Returning filling in including spreading leveling watering and well ramming in layers n exc 25cm all as specified and directed

Removal of excavated materials n. exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified.

M&L for plain Cement concrete 1:4:8 type D2 (using 40mm stone aggregate) in sub base filling and mass concrete all as specified and directed

M&L RCC M-30 (Design mix) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete

M&L RCC M-30 (Design mix) as in Columns, pillars, piers, posts and struts etc complete all as specified.

M&L RCC M-30 (Design mix) as in Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified

M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; verticle or to batter with rough finish flat surface.

M&L Formwork to sides of pillars, posts, struts, piers,columns, and stanchions, etc finish with rough finish flat surface.

M&L formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelvves including sup-ports, overhangs, etc. also splays between floors and beams, etc finish with rough finish flat surface.

M&L Fe -410-W(gde-E-250) Quality A Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces of any description over 10cm width or girth not otherwise described and all as specified and as directed.

M&L for 15mm thick rendering on fair faces of brick work/concrete surfaces in CM 1:4 finishing the surface fair & even (without using extra cement) complete all as specified and directed.

M&L for preparing newly plasterd surfaces of wall including priming the plastered surfaces and applying two coats of cement based paint complete all as specified.

M&L Brick work with sub class 'B' brick straight or curved on plan exc 6m mean radiaus built in cement mortor 1:6.all as specified and directed

M&L for brick work with sub class B bricks on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified

M&L for 10mm thick cement plaster in CM 1:4 other than fair faces of brick work or as a screed bed for vertical surfaces of wall complete all as specified and directed.

M&L for 15mm thick rendering on fair faces of brick work/concrete surfaces in CM 1:6 finishing the surface fair & even complete all as specified and directed.

Supply and fixing 10 mm dia and over mild steel TMT bars, cut to length, bent to shape required cranking bending and binding with and including mild steel wire annealed not less than 0.90 mm dia.all as specified and directed.

All as specified in item above here in before but 6 to 8mm dia as in stirups.

M&L RCC (nominal mix) Type B0 1:2:4 (12.5mm graded aggregate) as in Slabs supported on walls, beams and columns in floors ,roofs, landings, balconies,canopies,deck slabs and in shelves and the like.

Form work to soffits of suspended slab, roof beam haunching grider bressumers , lintels such as roof slabs, floor slabs, landings and similar work, n exc 200mm thick (Horizontal or sloping) complete all as specified.

M&L hardcore ( broken stone or boulders) of gauge n exc 63 mm deposited spread and leveled in layers n exc 15 cm thick watered and rolled / rammed to a true surface all as specified and directed.

M&L for 75 mm thick plinth protection in/Subbase PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) complete all as specified and directed.

M&L for 25mm thick cement concrete type B-1, 1:2:4 as in sub base under floor and finished rough surface complete all as specified.

M&L for 15 mm thick screed bed in cement mortar 1:6 for laying floor finishes complete all as specified.

M&L for Glazed ceramic tiles in vertical surface 300X200X7 mm thick set and jointed in neat cement slurry and pointed in colour cement to match.

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screeding laid and jointed in neat cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing ,complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with tapping screws as specified.

All as per item above herein before but plain sheet as in ridge, hipss valley etc all as specified.

S&F AC plain sheet ceiling 4mm thick on aluniminium snap grid work 60cm x 60cm with using 36.5mm 23.5mm x 1.5mm thick main tee, 23.50 x 23.50 x 1.28mm cross tee and 25 x 25 x1.5mm angle fixed to perimeter of wall for false ceiling including necessary supporting hanger with 3.0m dia GI wire and J bolts washer nuts for securing frome work to ceiling suspended @ 120 cm C/C both ways, size of grid shall be 610x610mm, including two coats of oil bound distemper on over one coat of primer and preparation of surface complete.

S&F for 2nd class soft wood, plain, solid, straight chowkats or frames, wrought framed rebated on the solid, rouned or chamfered, put together with flue pinned at joints.

S&F soild PVC door frame of size 50mm x 47mm made out of 5mm plaint colour PVC sheet reinforced with MS square tube, and fitted in opening all as specified.

M & L for mild steel hold fast of flat Iron size 25mm x 3mm thick for PVC door chowkhat etc as specified

S&F factory made solid PVC moulded door shutter with particle board core 28 to 30mm thick (style) with 2, 4, or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specificating and drawing.

M & L plain framed paneled shutter 2nd class soft wood 30mm thick (any number of panel) with panel of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkhats 30mm thick second class soft wood (Kail) complete all as specified and directed.

Glazed and Skelton shutters open rebated and prepared to receive glass, gauge etc (with sash bar) edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass etc supplied and fixed to chowkhat, 30mm thick shutter for window and ventilator as specified in SSR Part-I , Section-8, clause 8.24 (b).

S&F Sheet glass ordinary quality 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, in repairs, complete all as specified and as directed.

S&F for 100mm long stainless steel butt hinges medium weight cold rolled all as specified and directed by Engineer-in-Charge.

M&L for Aluminium handles cast type anodised 100mm long

M&L M&L for Aluminium alloy, anodised sliding door bolt 200mm long.

Mild steel butt hinge medium witht cold rolled 75mm size

S&F Mild steel opressed handle, oval ltype stove enamelled, black size of handle 150mm

Mild steel tower bolt stove enmelled black 150mm long black with bright bolt and fixed

Two coats of synthetic enamel paint including cleaning dusting of new or previously untreated, priming surfaces of wood of ply wood base surfaces for wall, door,window,ventilator and ceiling not otherwise described over 10cm width or girth complete all as specified and as directed by Engr-in-Charge.

M&L for treating ends of posts, back of chowkats etc with coal tar black paint, area tarred exc 0.10 sqm but n exc 0.50 sqm each including preparation of wooden surfaces.

M&L for 3 Coats of colour wash on newly plaster surface including preparation of surfaces.

M&L preparing newly plasterd surfaces and applying three coats of white wash on ceiling complete as specified.

M&L preparing newly plasterd surfaces and applying two coats of OBD over a coat of primer complete all as specified

S&F 500 Ltrs capacity rotational moulded polyethylene water storage tanks (Cylinderical vertical with closed top) and fixed in position, all as specified in SSR Part-I, including dismantling of old water tank of any description, complete all as specified and directed.

Stop valve 15mm bore, cast copper alloy screwed down, high kpressure, with crutch jor butter fly handlel, screwed bosth ends for iron pipe or for unioons and fixed in repairs.

Bib tap cast copper alloy chromium plated fancy type with crutch of butterfly handle, screwed down, screwed for iron pipe of for brass ferrule of 15mm bore (ISI marked).

S&F Pillar tap 15mm bore cast copper alloy, with capstain head chromium plated screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

M&L Lagging to pipes 15mmdia used in internal water supply or plumping all round with,25mm thick bonded mineral wool preformed 'SNAP ON' pipe sections of density 144 kg/cum conforming to IS-9842

M&L Lagging to pipes 20mm dia used in internal water supply or plumping all round with,25mm thick bonded mineral wool preformed 'SNAP ON' pipe sections of density 144 kg/cum conforming to IS-9842

S&F Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe and fixed with 20mm dia all as specified

S&F PVC (SWR) floor trap 75mm dia outlet, plain with grating including jointing with solvent cement complete all as specified.

S&F PVC connection 15mm dia and 600mm long with PTMT nuts and washer complete all as specified.

S&F 110mm bore PVC (SWR) pipe single socket in any length with rubber ring jointed, fixed to wall /floor etc complete all as specified.

S&F 75mm bore PVC (SWR) pipe single socket in any length with rubber ring jointed, fixed to wall /floor etc complete all as specified.

S&F 110mm bore PVC (SWR) bend or tee or radius complete all as specified.

S&F 75mm bore PVC (SWR) bend or tee or radius complete all as specified.

S&F PVC gully trap square or round mouthed type (P) , size of trap 125x 110mm and jointing to drains with solvent cement in repairs complete all as specified.

S & F Waste coupling of PTMT (half or full thread ). ( Minimum weight 32 mm-45 gms / 40mm-60gms) for 32mm bore dia of discharge pipe to WHB , sink .

S&F PVC valveless syphonic action type flushing cistern,low level white with inlet ball valve float and handle incl brackets (10 Ltr) capacity, with flush pipe etc fixed complete all as specified and directed.

M&L for Vitreous china water closet pan (pedestal pattern), white with seat cover and hinging device ,fixing bolts etc (excluding flushing cistern and including flush pipe) complete all as specified

S&F Vitreous China squatting pan "Orissa Pattern" size 580 x 440mm white with integral foot rests etc all as specified.

M&L preparing newly plasterd surfaces and applying three coats of white wash on wall etc complete as specified.

Vitreous china bowl urinal flat back, of size 465x355x265mm white (minimum), with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including discharge pipe of PVC 32mm dia complete all as specified and directed.

S& F PVC reducer couplings fixed at outlet of urinal pot incl. suitable length PVC flexible pipe 25 mmdia . ( Minimum weight 32 mm-45 gms) complete all as specified

S&F Soap dish chromium plated,any type, fixed to wall with chromium plated brass screw complete as specified

S&F vitreous china wash basin, white, flat back, size 550x400mm including waste chain & plug and porcelean stopper and including brackets, waste pipe, waste coupling etc complete all as specified

S & F tubular towel rail 60cm long, aluminium anodised fixed with and including CP brass screws and wooden/plastic cleats all as specified.

S&F GI steel water tubing medium grade galvanized with all fittings and fixed complete to walls, ceilings or laid on floors, bore of tube 15mm all as specified

Construction of 25 users septic tank (brick construction) including inlet and outlet chamber with top of slab at groung level including necessary earth work and disposal of surplus soil to a distance not exceeding 50m supplying and placing vent pipe,in position to manhole cover brick construction and all other relevant works,complete all as specified and shown on drawing No CESZ/TD-1080/2011 Sheet 1/1 dt 01/12/2011.

Construction of Septic tank including excavation in ordinary soil, foundation in PCC 1:2:4, brick work in CM 1:4, RCC slab covers including RCC precast manhole cover having 6mm plate embedded all around /fibre reinforced cover with angle iron frame vent shaft and sludge chambers etc complete for 10 users.

Construction of Soakage well exc, in ordinary soil, foundation in PCC 1:3:6 , well of Honey Cambed and solid in M-25 concrete, including intercepting chamber, screen chamber Brick work in CM, RCC cover slab in M-25 filling with brick bats of size 1.80 m dia and 3.0 m deep.

M&L for cement concrete bed (1:3:6) type C-2 using 40mm graded stone aggregate to drain pipes of 150mm bore including packing under hunching against the site of pipe after they are laid and tested.

M&L PCC 1:2:4 type B-1 (20mm graded aggregate) for coping, including weathering slightly rounded or chamfered using form work (straight or curved).

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds mitered/stopped ends.

Demolition of cement concrete (Un-reinforced) in ground floors and paving n.exc 15 cm thickness below or above ground level complete all as specified.

Dismantling wall and ceiling board of any description including cover fillets complete all as specified.

Dismantling of timber scantlings 40 sq cm and over in sec, in any position, in unframed/framed work complete all as specified.

Dismantling plain or corrugated steel sheeting any gauge thickness in roof covering/wall etc complete all as specified.

M &L for second class soft wood as in scantling clean sawn fixed in position complete all as specified.

M & L for second class soft wood as in scantling clean sawn fixed in position but except wood.

Taking down chowkhats or frame exc. 1.5sqm and n.exc. 4 sqm each with shutter (without taking out shutters from the frame) complete all as specified.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed

M&L weather boarding of second class soft wood,clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm lap in repair to replace old or decayed boarding and removing from site complete all as specified and directed.

S&F 200mm long aluminium alloy, anodised barrel tower bolt of extruded section complete all as specified.

S&F 300mm long aluminum alloy anodized sliding door (bolt type) and fixing clips of sheets, cast of extruded sections and fixing bolts and sliding bolts of extruded section of cast-aluminum alloy complete all as specified.

S&F aluminum handles, cast type, anodized 150mm long complete all as specified.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work, complete all as specified and directed.

Walling of random rubble stone uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

Description all as per item above but except stone all as specified and directed.

Rendering 15 mm thick in CM 1:4 on stone masonary surfaces or surfaces other than fair faces of brickwork and finishing even & smooth without using extra cement.

M&L Non skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm and n.exc 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface, complete all as specified and directed.

M&L Plain fillets rectangular or triangular in section clean sawn secured with nails or brads exceeding 3 sqcm & n exc 6 sqcm, second class soft wood (Kail) clean sawn complete all as specified.

M&L for 6mm thick veneered decorative plywood (05 Nos of ply) grade-01 (with BWR resin) with decorative face veneers on the one face fixed with nails to timber frame works fixed in wall/linings complete all as specified.

M&L for 6mm thick veneered decorative plywood (05 Nos of ply) grade-01 (with BWR resin) with decorative face veneers on the one face fixed with nails to timber frame works fixed in ceiling etc complete all as specified.

M&L for 75mm thick Plain Cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) in sub base flooring all as specified and directed

M&L for Chequered cement concrete tiles 20 cmX20 cmX25 mm thick sat jointed and pointed in neat cement slurry in floor with grey cement and no pigments with 1:4, 25 mm thick screed bed.

Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

Point wiring for one light point/Ex/fan point controlled by one switch with 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi strand cable and 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi stranded cable (green color) as earth lead in and including cable 1100 volts grade including 25mm casing and capping (ISI marked) for one light/ fan point controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified.Make : Finolex/Anchor/Polycab

Point wiring for 3 pin 5A socket outlet independent point controlled by one switch with 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi strand cable and 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi stranded cable (green color) as earth lead, 1100 volts grade including 25mm casing and capping (ISI marked) for one light/ fan point controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified.Make : Finolex/Anchor/Polycab

Point wiring for 3 pin 5A socket outlet on the same board controlled by one switch with 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi strand cable and 1.5 sqmm PVC FRLS insulated un-sheathed copper conductor single core multi stranded cable (green color) as earth lead, 1100 volts grade including 25mm casing and capping (ISI marked) for one light/ fan point controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified.Make : Finolex/Anchor/Polycab

Point wiring for one 3 pin 15 Amps socket outlet/sheet metal enclosure independent with 4.00 sqmm PVC insulated un-sheathed copper conductor single core multi strand cable and 2.5 sqmm PVC insulated un-sheathed copper conductor single core cable (green color) as earth lead in and including 25mm PVC caping casing medium grade with all fittings (ISI Marked) controlled by one switch including CI/MS sunk box of required size, & as directed by Engr in Charge including 3mm thick plastic laminated top sheet cover, including cutting chases to wall and making good the disturbed surfaces to match with the existing specification complete all as specified.Make : Finolex/Anchor/Polycab

M&L for LED Tube light fitting of 1x20 W for Decorative ultra slim square profile with extruded polycarbonate, environmental friendly, energy efficient ready to use pack of LED Pride Plus NEO and connecting electrically using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed by Engineer-in-Charge.Make :Havells Batten Cat part No LHEXACP7IN1W020 or equivalent ISI Marked company.

S&F Switch piano type flush 6 Amp Single pole one way ( ISI Marked) complete all as specified and directed. Make : Havells/Anchor

S&F Switch socket combination 5 in 1, 5 and 15 Amp flush type universal controlled by one switch (ISI marked) complete all as specified and directed. Make : Havells/Anchor

S&F Socket outlet 2 in1, 3 pin 5 Amps flush type complete all as specified and directed.Make : Havells/Anchor

S&F ceiling rose surface backelite 65x50mm two to three terminal (ISI marked).Make : Havells/Anchor.

Supply and fixing lamp holder bracket type, PVC/polycarbonate type with skirt cap suitable for batten fittings, complete all as specified and direted.Make : Havells/Anchor

Supply and fix LED Bulb 9 Watt for Item Above. Make Havells/Bajaj

Supply and fix surface mounted decorative bulk head edge -lit LED Luminaire comprsing of high brightness LEDs of 1x10 W LED having PF not less than 0.9 all as specified and directed. Make - Havells cat part No LHEOAOP7UZ6W010 & equivalent.

S&F RCBO, single pole and neutral (SPN) 30mA, 240V , 32 Amp all as specified and directed. Make- Havelles/MDS/Legrand.

S&F MCB 'C' series, single pole 240V , 6 to 32 Amp all as specified and directed. Make- Havelles/MDS/Legrand.

Supply & fix sheet metal enclosure MCB distribution board. Single pole & neutral 240 volts 6 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, conf to Cat Pt No 6077 11 of Legrand or equivalent of make Hager/Merlin Garin fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification.

Supply & fix sheet metal enclosure MCB distribution board. Single pole & neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, conf to Cat Pt No 6077 11 of Legrand or equivalent of make Hager/Merlin Garin fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification.

Supply & laying of PVC flat twin core cable of 1100 Volts grade with stranded aluminium conductor of size 10.0 sq mm 2 core complete all as specified and directed.Make Havells/Polycab/Gloster

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6.3cm thick burried directly in ground ( earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanised iron wire 4.0mm dia by means of bolts, nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 connected to earthing test all as specified or indicated including testing on completion.

Cutting the 40/25 mm dia GI pipes and fixing the required length/ insertion of tee for new GI pipe connections all as directed.

Cutting the 25/20 mm dia GI pipes and fixing the required length/ insertion of tee for new GI pipe connections all as directed.

S&F GI water tubing ISI marked 20mm bore, galvanised medium grade, with all fittings like socket, union, elbow, bends, tees etc jointed and laid in trenches, complete all as specified directed by Engr-in-Charge. Make- Kalinga, Prakash, Surya, Jindal.

S&F GI water tubing ISI marked 25mm bore, galvanised medium grade, with all fittings like socket, union, elbow, bends, tees etc jointed and laid in trenches, complete all as specified directed by Engr-in-Charge. Make- Kalinga, Prakash, Surya, Jindal.

20mm bore gun metal globe gate valve (ISI marked) iron wheel head,screwed both ends for iron pipe fixed in repair complete.

Lagging of pipes used in internal water supply or plumbing all round with 40mm thick bonded mineral wool performed 'SNAP ON' pipe section of density 144 Kg/Cum conforming to IS 9842 for 20mm dia provided with chicken mesh wire netting 25 gauge , 20mm mesh complete all as specified and directed by Engineer-in-Charge.

M/S MOHD YOUSUF CONSTRUCTION CO

M/S SS SHAH WALI & CO

M/S AB AHAD RATHER

M/S AK CONSTRUCTION

M/S WALI AHMED AND SONS

M/S SAJAA CONSTRUCTION COMAPNY

patriotic builders

Bidder Name

M/S AB AHAD RATHER

M/S SAJAA CONSTRUCTION COMAPNY

patriotic builders

M/S WALI AHMED AND SONS

M/S GHULAM RUBANI & SONS

M/S SS SHAH WALI & CO

M/S AK CONSTRUCTION

M/S MOHD YOUSUF CONSTRUCTION CO