CERTAIN REPAIR TO JOINERY, PANELING, CEILING CURTAIN ROD, GLASS, WIRE MESH, CUPBOARD AND CONNECTED ITEMS IN 536 ASC, 3/3 GR, 115 BDE, 97 FD, ARO GE OFFICE AND NEARBY AREA UNDER AGE B/R-II

Amount

Taking down chowkhat or frame (without taking off shutter from the frame) not exceeding 1.5 Square Metre each, removing from the site Cutting holes exc 150 Sq.cm but n.exc 400 Sq.cm in super facia area into or through brick walls built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as required complete all as specified and as directed.

Taking down chowkhat or frame (without taking off shutter from the frame) exceeding 1.5 Square Metre each not exc 4.00 sqm, removing from the site Cutting holes exc 150 Sq.cm but n.exc 400 Sq.cm in super facia area into or through brick walls built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as required complete all as specified and as directed.

Taking down shutter of any description not exceeding 1.00 sqm each complete all as specified and directed.

Taking down shutter of any description exceeding 1.00 sqm but not exceeding 2 sqm each complete all as specified and directed.

M&L for 2nd class hardwood palin, solid, straight chowkhat and frames wrought frame rebated on solid rounded and chamfere put together with glue pinned at joints complete all as specified and directed.

S&F pressed steel frame 105mmx60mm for doors with one or more rebates including S&F necessary lungs and hinges(min 100mm size), lock strike plate,etc as per IS requirement complete all as specified and directed.

S&F pressed steel frame 125mmx60mm for doors with one or more rebates including S&F necessary lugs and hinges (min 100mm size), lock strike plate, etc as per IS requirement complete all as specified and directed.

M&L for 35 mm thick glazed and skeleton factory made shutters of 2nd class Hard Wood, open rebated and prepare to reveive glass, guage etc (without sash bars) edges of framing plain chamfered or rounded, fitted with moulded beads both sides for securing glass etc, size of members of shutters as specified complete all as specified and directed.

S&F 30mm thick Flush shutters soild core construction with particle board core and plywood face panels, commercial type complete all as specified and directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet 5 mm thickness to be fitted in MS frame welded/sealed to the style and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed.

Same as Item No 11 but wire guage panel i.e. panel should be wire guage in lieu of PVC sheet panel. Wire guage shall be wraped on a additional square tube 8mm M.S. solid tube and tube shall be welded to M.S. tube. and wire guage shall be strechted tightly firmed complete all as specified and as directed.

S&F Factory made Solid PVC Moulded door shutter, 28 mm to 30 mm thick (stiles) with 2, 4 or 6 raised panel design with 2 mm thick moulded Prelam PVC sheet on the front face & 2 mm prelame PVC Sheet on back face complete all as specified and directed.

M&L for preperation of new wooden surface and applying two coats of synthetic enamel paint over a coat of pink primer on new wooden surface any description not otherwise described over 10 cm width or girth and complete all as specified and directed.

S&F for 100 mm long size aluminium alloy anodised hinges medium weight complete all as specified and directed.

S&F for 200mm long aluminium anodised, barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F for aluminum handles cast type, anodized of 150 mm size complete all as specified and directed.

S&F for butt hinges 100mm long medium weight, cold rolled mild steel complete all as specified and directed.

S&F for Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

M&L for Powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

M&L for Powder coated (minimum thickness of powder coating 50 micron) aluminium door shutters of aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, powder coated aluminium handles 150mm size 2 Nos, 3 Nos powder coated aluminium hinges heavy duty and 02 Nos 150mm long powder coated aluminium tower bolts in each door shutter with powder coated aluminum snap beading, screws etc complete all as specified and directed. Note : Panel filling i.e. glass, fibre sheet, board etc shall be measured and paid for separately.

M&L for Powder coated (minimum thickness of powder coating 50 micron) aluminium window and ventilator (adequate track(openable)) without sash, aluminium section weighing 0.55 kg/m including joining cleats, glazing clips, rubber neoprene packing, necessary powder coated hardware i.e. handles, barrel tower bolts, hinges etc, powder coated aluminum snap beading, screws etc complete all as specified and directed. Note : Panel filling i.e. glass, fibre sheet, board, wire mesh etc shall be measured and paid for separately.

S&F for Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F for renewal of door closer hydraulically regulated, designation No. 3, universal type, aluminium die-cast body (ISI Marked), suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

S&F for renewal of double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed.

S&F in renewal 3mm thick, ordinary glass pin head type and glazing with oil putty, silicone or wooden beads, in square not exceeding 0.5 sqm in each pane including hacking out old broken glass of any thickness and any description from wooden/ steel frame/ stone, concrete or brick surrounds complete all as specified and directed.

S&F in renewal of galvanised wire cloth, 0.48mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised staples complete all as specified and directed.

S&F for Box type steel windows with side hung shutters (double shutters for glass and guaze) jointed together with an including grills using 10mm square bars @10 cm C/C as per TD No CEBZ/TD/14/2011 including box type hinges with steel handle and steel peg stay complete with glazing bars dovetailed and welded including filling of PCC 1:3:6 type C-0 (using 12.5 mm graded stone aggregate) in hollow section of frame complete all as specified and directed. Note : Glass/guage shall be measured and paid separately under respective item.

S&F for framed work such as grills gratings, etc, with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to F- 290 GDE -165, complete all as specified and directed.

S&F for 3mm thick, ordinary glass pin head type and glazing with oil putty, silicone or wooden beads, in square not exceeding 0.5 sqm in each pane complete all as specified and directed.

S&F for galvanised wire cloth, 0.48mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised staples complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint as one coat of primer including Preparation of new Steel surface over 10 cm width or girth comlete all as specified and directed.

M&L for PCC 1:3:6 type C0 (using 12.5mm graded stone agrregate) for filling in pressed steel frames and like complete all as specified and directed.

Resecuring, easing or adjusting without taking down door/ windows shutters not exceeding 1 Sqm for easy operation, tightning hinges, adjusting position of hinges, tower bolts, sliding bolts etc including provision of necessary screws complete all as specified and directed.

Resecuring, easing or adjusting without taking down door/ windows shutters of any type wooden/aluminium exceeding 1 Sqm but not exceeding 2 sqm for easy operation, tightning hinges, adjusting position of hinges, tower bolts, sliding bolts etc including provision of necessary screws complete all as specified and directed.

Resecuring, easing or adjusting without taking down door/ windows shutters of any type wooden/aluminium exceeding 2 sqm for easy operation, tightning hinges, adjusting position of hinges, tower bolts, sliding bolts etc including provision of necessary screws complete all as specified and directed.

Repair aluminium door and window shutters by taking down shutter from frame, opening out joints, taking out glass or panels of any description, replacing the corner piece wherever required, joining and assembling again, refixing the glass pane and panels by provision of new rubber neoprene packing complete all as specified and directed.

Taking down and refixing of shutter of any description Note : Refixing including taking down easing and adjusting and also refxing builders hardware as required including removal of unserviceable screws etc. Hardware items will be paid at supply only rates except screws and nails Not exceeding 1 Sqm each.

Same as item No 40 but exceeding 1 Sqm n.exc 2 Sqm each complete all as specified and directed

Same as item No 40 but exceeding 2 Sqm each complete all as specified and directed.

Supply only 150 mm long Aluminium anozied barrel tower bolt of extruded section complete all as specified and directed.

Same as item No 43 but 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

Same as item No 43 but 100 mm long Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised complete all as specified and directed

Same as item No 43 but 75mm long Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised complete all as specified and directed.

Same as item No 43 but 150mm long mild steel pressed handles, oval type, stove enamelled black complete all as specified and directed.

Same as item No 43 but 150mm long aluminium handles, cast type, anodised complete all as specified and directed.

Same as item No 43 but 30mm width of flaps (when open) Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F in renewal of Mild steel Drawers or almirah handles, projections drop (50mm to 65mm) on screwed plate complete all as specified and directed.

S&F in renewal of 150 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F in renewal of 150mm Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F in renewal of Peg stays to steel windows/ ventilator complete all as specified and directed.

S&F in renewal of handles to steel windows / ventilator complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar (1:6) on brick / concrete/ stone surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 15 mm thick rendering in cement mortar (1:4) on brick / concrete/ stone surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of the newly plastered surfaces of wall & applying 3 coats of white wash on wall surfaces complete all as specified and directed.

M&L for two coats of oil bound emulsion paint over a coat of Birla wall care putty on plastered surfaces on wall including preparation of surfaces complete all as specified and directed.

Preparation of old decorated surface by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down, smoke soot moulds, moss and efflorescent salts treating oil and greasy spots on old plastered or unplastered surfaces of wall including cornices, pilasters etc and applying one coat of white wash, complete all as specified and directed.

Preparation of old decorated surface by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down, smoke soot moulds, moss and efflorescent salts treating oil and greasy spots on old plastered or unplastered surfaces of ceiling including cornices, pilasters etc and applying one coat of white wash , complete all as specified and directed.

Preparation of old decorated surface by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down, smoke soot moulds, moss and efflorescent salts treating oil and greasy spots on old plastered or unplastered surfaces of wall including cornices, pilasters etc applying one coat of oil emulsion distemper on walls including preparation of old plastered or un plastered surface complete all as speified and directed.

Preparation of old decorated surface by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down, smoke soot moulds, moss and efflorescent salts treating oil and greasy spots on old plastered or unplastered surfaces of wall including cornices, pilasters etc applying two coats of oil emulsion distemper on walls including preparation of old plastered or un plastered surface complete all as specified and directed.

M&L for preparation of wall surface and aplying wall putty minimum 1mm thick on wall surface finished even and smooth including rubbing complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint including Preparation of old painted wooden surface any description not otherwise described over 10 cm width or girth and complete all as specified and directed .

M&L for applying one coat of synthetic enamel paint as one coat including Preparation of old Steel surface over not otherwise described over 10 cm width or girth all as specified and directed .

S&F in renewal of 5mm thick PVC sheet fillet of width 35mm for wall panelling (At the spacing of 1 feet centre to centre) inclusive of fixing on to wall to make PVC Frame as per secification and drawing comlplete all as specified and directed.

S&F in renewal of Solid PVC Wall Lining consisting of 5mm thick Plain wood grain printed PVC sheet inclusive of solvent cement and fixing at site on to wall to make PVC Frame as per specification and drawing comlplete all as specified and directed.

Demolition of wall and ceiling boards fibre pulp insulation etc or insulation boards/slabs/blankets any thickness including cover fillets, complete all as specified and directed.

S&F for Providing & fixing false ceiling at all heights with GRG (Glass Fibre With Reinforced Gypsum) false ceiling tiles of semi perforated 12mm thick micro tegular edged GRG of size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS tiles 476 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000mm, cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of size 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e. 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1OOOmm length and L shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge complete all as specified and as directed.

Dismantling boarding any description fixed with nails in any position (including cup board shutter/shelve upto 25mm thick) complete all as specified and directed.

S&F for 18 mm thick PVC Celuka ply of both side prelaminated and other side plain white colour fixed with screws, solvent cement /adhesive complete all as specified and directed.

S&F for 12 mm thick PVC Celuka ply of both side prelaminated and other side plain white colour fixed with screws, solvent cement /adhesive complete all as specified and directed.

S&F for aluminium anodised barrel tower bolts of extruded section of 100mm size, complete all as specified and directed.

S&F for continuous (piano) hinges mild steel bright finish or electro galvanised width of width of flaps n.exc 30 mm (when open), complete all as specified and directed.

S&F for extruded aluminium alloy handle of 100 mm size fabricated type, anodised complete all as specified and directed.

S&F for Haps and staple safety type Aluminium anodised with MS hinge pin including bolt to hinge pin of 100 mm size sixed with screw complete all as specified and directed.

S&F for magnate catcher of metal body and striking plate heavy duty including fixed with screw, complete all as specified and directed.

S&F for 25mm dia stainless steel curtain rod not less than 0.80mm thick including fixing of sufficient brackets (minium 2 nos at every 1.50m length) & end Knobs complete all as specified and directed.

Demolition of brick work /stone work built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L for Brick work with sub class B bricks straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and as directed.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius, in half brick work built in cement mortar 1:4 complete all as specified and directed.

J.N.R. Engineers and Builders (BID ID -3402495)

RADHA MADHAV CONSTRUCTIONS (BID ID -3402953)

Babatia super works (BID ID -3402739)