GE(S)/M-39/2022-23

Amount

Demolition of cement concrete (unreinforced) of any description and in any position not specifically provided for, complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not specifically provided for, complete all as specified and directed. Note :-Reinforcement cut as required to facilitate demolition.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc including brushing with neat cement slurry with 3.0 Kg of cement per Sqm complete all as specified & directed.

Taking down existing cement plaster on brick walls or stone walls of any description etc. including raking out joints, hacking for key, scrubbing down with water etc, including removal of debries out of MoD land complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 Sqm each and removing from site, complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc. 1.5 Sqm but not exc 4.00 Sqm each and removing from site, complete all as specified and directed.

Taking down shutters of any description exc.1 Sqm but not exc 2.00 Sqm each and removing from site, complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6 Mtr mean radius, built in CM 1:6, including demolition of existing brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, including removal of deberies out of MoD land complete all as specified and directed.

S&F pressed steel frame of size 125mm x 60mm for doors with one or more rebats including necessary fixing lugs, hinges, lock strike plate including filling of PCC 1:3:6 type C-0 (using 12.5mm graded stone aggregate) in frames/hold fast blocks, including two coats of synthenic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F pressed steel frame of size 105mm x 60mm for doors with one or more rebats including necessary fixing lugs, hinges, lock strike plate including filling of PCC 1:3:6 type C-0 (using 12.5mm graded stone aggregate) in frames/hold fast blocks, including two coats of synthenic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F 35mm thick factory made wire guazed and skeleton shutters (1st class softwood), open rebated and prepared to receive wire cloth, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing wire cloth etc. sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) and fitted to chowkats at site, complete all as specified and directed.

M&L for 40 Flush shutters, particle board core construction, with particle board core and plywood face panels, commercial type on both sides complete all as specified & directed.

S&F for Box type steel windows comprised of tubular frame and shutters made out of 1.25 mm thick MS sheet tube factory made with double side shutters wire gauged shutter & glass glazed shutter (wire cloth and glass panes will be measured and paid seperately) with side hung shutters with MS handles and MS peg stay dovetailed or welded incl 02 Nos, MS Tower bolts 150 mm long for each leaf and 8 mm square bar grill / guard bars at spacing as shown on Drg welded to MS flat iron frame work ,including other fittings ,hinges ,MS handles ,tarred hold fasts ,PCC blocks for hold fasts etc all as shown on Drg No CEPZ/TD -27/13 sheet 1/4 to 4/4 including two coat of synthetic enamel paint r, complete all as specified and directed

S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ choowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs fasteners shall be paid for separately). complete all as specified & directed.

S&F 35mm thick H.D.F prelaminated (Wenga/Teak colour) moulded shutter 35 mm thick puf (poly urathane foam) insulation with minium density 40kg/cum filled in between two HDF sheets of thickness 3.2 mm both & border covered with 10 mm thick PVC sheet as per Drg No. CEPZ/TD-378/Sheet 1/1 dated 27/12/2011 complete all as specified and directed.

M&L for Hasp and staple 100 mm in size, aluminium anodised, including bolt to hinge plate and fixed with screws complete all as specified and directed..

Supply & fixed in repair factory made 18mm thick WPC(wood particle composit) sheet one side prelam sheet and other side wood nature colour for cupboard shutter of density 600 kg /Cbm bent 90° incl 100% termite/water proof, fire rertradent, Eco friendly, and finish at all edges at level for making edges lipping using binding tape etc. complete all as specified and directed.

S&F Stainless steel designer handle (heavy duty) of 100mm size, fixed to drawers or cupboard shutters, complete all as specified & directed.

S&F continuous (piano) hinges, mild steel, bright finish width of flaps (when open ) 40 mm all as specified and directed.

S&F for Butt hinges 100 mm long, stainless steel, medium weight and fixed complete all as specified.

S&F Aluminium alloy, anodised, sliding door bolt 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or castaluminium alloy and fixed complete all as specified.

S&F Aluminium, anodised, barrel tower bolts 200 mm of extruded section and fixed complete all as specified.

S&F Aluminium, anodised, barrel tower bolts 150 mm of extruded section and fixed complete all as specified.

S&F Aluminium, anodised, handles 125 mm of extruded section and fixed complete all as specified.

S&F for floor door stopper of 140mm long cover plate of aluminium alloy body and tongue anodised with hard drawn steel spring, fixed in floor complete all as specified and directed

S&F Mild steel, 300mm, ordinary rat tail rod patttern springs includding roller and roller plate complete fixed with screw or necessary welding to pressed steel door frame complete all as specified.

S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with statinless steel wire staples complete all as specified..

Hacking out old broken glass (any thickness, size, quality or description) from matel frame including punching or drilling out old glazing pins/spribng clips complete all as specified and directed.

S&F, 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc. 0.5 sqm in each pane , complete all as specified and directed.

S&F 3mm thick figured glass, pin head type and glazing with oil putty or wooden beads in square n.exc 0.5 sqm each complete all as specified & directed.

S&F "as in repair" 25mm outer dia stainless steel decorative drapery rod of thickness 20 guage with stainless steel brackets near to ends with stainless steel finials with adopter for 25 mm dia drapery rod at both ends complete all as specified and directed.

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc; and cutting chases for concealed water tubing ,etc., and making good, cutting not exc 20 cm girth in brick walls, complete all as specified.

S&F steel water tubing 15 mm bore medium grade galvanised with all fittings (ISI marked) fixed complete to walls, ceiling or laid in floors complete all as specified.

Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing in the same or other position with all fittings, complete all as specified and directed.

S&F Rotational moulded polyethlene water storage tanks three layers of 1000 ltrs capacity ISI marked (cylindrical vergical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm thick Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including Dismantling of old brocken water tanks and refixing of inlet, outlet & over flow pipe etc complete all as specified and as directed.

Supply & Fixed in repair Bib tap 15 mm bore Brass CP, fancy type, with crutch or butterfly handle screwed down screwed for iron/PVC pipe or for brass ferrule and fixed, complete all as specified and as directed.

S&F in repair Stop valve/Angle valve (ISI Marked), fancy type cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore ccomplete all as specified and as directed.

S&F in repair Stop valve (ISI Marked) 15 mm bore fancy type, chromium plated with long shank and cup (concealed type), cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore complete all as specified and as directed.

S&F in repair, Shower rose swivel type brass chromium plated 150x150 mm size including fixing to steel pipe or unions complete all as specified and as directed.

S & F in repair corner glass shelf with bracket fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed. .

S&F in repair, Vitreous china squatting pan of pattern, long pan, 'Orissa pattern', size 580 x 440 mm white with integral foot rests (excl flushing cistern and flush pipe) but including provision of lime concrete complete all as specified..

S&F , Vitreous china wash down water closet pan (Pedestal pattern) white (excl fixing bolts, flushing cistern and flush pipe) but including plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel CP or aluminised hinging device complete all as specified and as directed.

S&F ,Vitreous China Urinal, Half stall type, white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing of automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) fixed incl supply and fixing of CP coupling, waste pipe and all necessary fittings, complete all as specified and directed.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe (minimum weight 60 gms) complete all as specified and as directed.

S&F in repair PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle (incl brackets & flush pipe PVC 32 mm dia) capacity of 10 Litres complete all as specified and as directed.

S & F Counter top wash hand basin, oval,white of size 550x400mm, excluding taps, waste, chain and plug and porcelain stopper but including brackets and PVC waste pipe with union, flexible suitable for wash hand basin or urinal, 32 mm dia complete all as specified and as directed.

S & F 32 mm dia, Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 suitable for waste pipe etc fixed complete to walls, ceilings or in floors etc.complete all as specified and as directed.

S & F in repair, Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed.

S & F Brass CP towel rail 20mm dia 'D' type 60 cm long between flanges complete all as specified and directed.

S & F, PVC connection 15 mm bore with PTMT nuts of length 450 mm long complete all as specified and as directed.

S & F, Brass CP jet spray with complete assembly suitable for EWC pedestal pattern including PVC flexible pipecomplete all as specified and as directed.

Taking down old/broken cast iron pipes of any dia from existing lines fixed to walls with clamps or laid in trenches (Including necessary excavation) complete all as specified and as directed.

S&F in repair 100 mm bore sand cast iron soil waste and vent pipes ISI marked in any length with or without ears laid in floor or wall with lead joints complete all as specified & directed.

S&F in repair 75 mm bore sand cast iron soil waste and vent pipes ISI marked in any length with or without ears laid in floor or wall with lead joints complete all as specified & directed.

S&F in repair CI floor trap 75 mm with grating including jointing to waste pipe ISI Marked fixed in cement concrete 1:2:4 type B-1 with CP grating complete all as specified & directed.

S&F in repair CI floor trap 100 mm with grating including jointing to waste pipe ISI Marked fixed in cement concrete 1:2:4 type B-1 with CP grating complete all as specified & directed.

S&F in reapirs Cast iron nahani trap 75 mm with grating ISI Marked including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified & directed.

S&F in repair 100mm dia CI bends (any radius) diminishing pieces or tapers (larger bore measured) ISI Marked complete all as specified & directed.

S&F in repair 75mm dia CI bends (any radius) diminishing pieces or tapers (larger bore measured) ISI Marked complete all as specified & directed.

Cast Iron Branch peices, single (equal or unequal) ordinary or inverted (spigot or socket type), or with parrallel branches fitted with oval access doors of 100 mm bore dia complete , ISI Marked, fixed in repairs complete all as specified & directed.

M&LCast Iron Branch peices, single (equal or unequal) ordinary or inverted (spigot or socket type), or with parrallel branches fitted with oval access doors of 75mm bore dia complete , ISI Marked, fixed in repairs complete all as specified & directed.

S&F in repair cast iron cowl 75 mm dia ISI Marked complete all as specified & directed.

M & L for10 mm thick cement plaster in cement mortar 1:3 on brick or concrete surface of sunken floor finished even and smooth with and including WPC liquid as per manufacturer instruction @ 0.200 ltr in 50 Kg of cement complete all as specified & directed(WPC shall be measured and paid separately) complete all as specified & directed.

M & L for bitumen blown any grade, applied hot, two coats, to concrete/plastered surfaces at the rate of 1.5 Kg per sq m per coat and applying polythene film black, 50 micron complete for sunken floor slab and embedded in side wall / covered fillet complete all as specified and directed.

M&L for Cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in mass filling in sunken slab of toilets, complete all as specified & directed.

M & L for 25 mm thick P. C.C type B-1, 1:2:4 ( using 20mm graded aggregate) as in sub floors for laying floor finish complete all as specified and directed.

M&L for Non skid ceramic jointless coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but nexc 0.18 sqm in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 15mm thick screed layer in cement mortar 1:6, complete all as specified and directed .

M&L for Glazed ceramic coloured tiles of size 450mmx300mm, thickness 7mm as in vertical surfaces such as skirting, dado, wall etc., set and jointed in neat cement slurry and pointed with coloured cement to match over and including 10mm thick rendering in cement mortar 1:4, complete all as specified & directed.

M&L for 20 mm thick green/ black marble (of any type) work (table rubbed & polished) in steps, jambs, pillars, window-cills cooking platforms & like including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite laid over and including Screed bed or bedding layer of mortar 15mm thick for laying floor in CM 1:4 finished even & rough to receive top layer, complete all as specified and directed.

M&L for Machine cut Kota stone slab flooring not less than 18-20 mm thick (size of stone shall not less than 55cmx55cm), 75mm wide white marble border alround, laid over & including 15 mm thick screed base in CM 1:6, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing to yield mirror finish with machine, complete all as specified.

M&L for Machine cut Kota stone slab not less than 15mm thick as in riser of steps, skirting, dado and pillar laid over & including 10 mm thick screed base in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing to yield mirror finish with machine, complete all as specified.

M&L for 60mm thick, M-35 grade coloured machine pressed precast rubber moulded concrete interlocking (Red/yellow) paver block of any shape and size with 6-8mm white cement layer mixed with pigment and coated with epoxy coating having high glossy finish confirming to IS 15658-2006, laid dry over and including 50mm thick sand filling under paver, properly levelled etc, complete all as specified and directed.

M&L for precast designer coloured Endura tiles with glossy finish (factory made rectified) of size 300mmx300mmx10mm, top layer glazed made in any type of cement and pigment, in required patterns in floor etc set & jointed in neat cement slurry & pointed in white or coloured cement mixed with pigment to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:6 for laying floor finishes, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for cement concrete type C-2, 1:4:8 (40mm graded agg) as in Sub-base to floor finishes complete all as specified & directed.

M&L for Rendering 10 mm thick plaster in cement mortar 1: 3 on concrete surfaces as in ceilings finished even and smooth without using extra cement, complete all as specified.

M&L for Rendering 10 mm thick on fair face of brick work or concrete surface in CM 1:6, finished even and smooth without using extra cement complete all as specified & directed.

M/L for 15 mm thick rendering in two layers (5 mm thick in CM 1:4 over 10 mm thick in cement mortar 1:6) mixing with and including WPC @ 200 ml/ bag of cement on brick or concrete surfaces and finished even and smooth without using extra cement all as specified.

Taking down cement plaster and decayed concrete of any description, upto double storey of building, from roof projection, chajja etc and making good the decayed portion with cement mortar 1 :3 mixed with water proofing compound as per manufacturers instruction or PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) including necessary form work and finally finished the surface with 15mm thick cement plaster in CM 1:3 , complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:3:6, type C2 (using 40mm graded agg) as in plinth protection finished even and smooth using extra cement.(incl necessary joint filling with mixture of paving bitumen & sand in 1:3) complete all as specified & directed.

M&L for Preparation of newly plastered surface of wall and applying two coat of oil bound distemper, white or tinted shade with and including wall care putty 1mm to 2mm thick over plastered surface of wall, complete all as specified.

M&L for Complete removal of existing treatment of wall surfaces and applying two coat of oil bound distemper, white or tinted shade with and including wall care putty 1mm to 2mm thick thick over plastered surface of wall, complete all as specified.

M&L for Complete removal of existing treatment of external wall surfaces such as RCC fins/facias/roof projection etc and applying two coats of all weather coat or Appex paint complete all as specified & directed. .

M&L for preparing newly plastered surfaces and applying three coats of white wash as in ceiling etc complete all as specified & directed.

M&L for preparing of plastered surfaces of ceiling, old decorated surfaces and applying one coats of white wash complete all as specified & directed.

M&L for preparing of Old painted surfaces of steel or iron surfaces of any description, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed.

M&L for preparing of Old painted surfaces of wood of any description not otherwise described over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified & directed.

M&L for preparation of new surfaces of wood & wooden of any description exc 10cm width or girth and applying two coats of synthetic enamel paint, over a coat of pink primer complete all as specified & directed.

Dismantling of plain or corrugated AC sheeting, any gauge, thickness, including ridge etc as in roof covering complete all as specified & directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified & directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified.

S&F for Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified & directed.

M&L False ceiling of 9.5mm thick gypsum tiles (600x600mm) laminated with PVC film on the face side & metalised polyester film on the back side with all four edges sealed with PVC film (shade either plain white or crack) fixed using T grid/Cross-T/Wall angle/level clip & suspenders of standard galvanised sections in a grid size of 600x600mm, including taking down existing ceiling board & grid work etc of any type/pattern complete all as specified and directed.

M&L for 25 mm thick (average thickness) PCC1:2:4, type B-0 using 12.5mm graded stone aggregates as in floor by maintaing required gradient/undulation, finished even and fair as in roof padding including prepration of surface and mix with and including water proofing compound and finished even and fair without using extra cement, complete all as specified and directed.

M&L for Complete removal of the existing roof treatment any nos of layers taken out membrane, PCC Padding/roof, tiles etc including grubbing up of tree roots , roughing and prepration surfaces of old concrete floor by picking , scrubbing down with steel brushes, sweeping, cleaning and washing down with water to remove dust etc. and applying the following Roof treatment complete all as specified and directed. (a)Applying 1st course of 15 mm thick screed bed with cement mortar 1:4 over old concrete surface (b)Applying 2nd course of bitumenous primer @ 0.4 kg/Square Metre conforming to IS-3384 over screed bed . (c)Applying 3rd course of a coat of bonding material with blown type bitumen of grade 85/25 heating to working temperature of 180 centigrade and applied @ 1.2 kg/Square Metre. (d)Applying 4th course of APP (Atactic Polypropylene) modified polymeric 3mm thick, weight not less than 3.6 kg/Square Metre with 160 Grams/Square Metre non woven polyster made at center core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane shall be laid with LPG torch and overlap sealed and finished neat . (e)Applying 5th course of a coat of bonding material with blown type bitumen of grade 85/25 heating to a working temperature of 180 centigrade and applied @ 1.2 kg/Square Metre . (f) Applying a coat of bitumenous based aluminium paint as finishing coat complete all as specified & directed.

M&L TMT bars but 6mmto 10mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in lintels upto 1..5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item, complte all as specified and directed.

Use and waste of formwork to soffits of concrete fair finished surfaces of suspended slabs such as roof slab,floor slabs landings and similar works not exc 200 mm thick complete all as specified and directed.

Taking down carefully aluminium / copper point wiring (light, fan, socket or power) complete including fixtures and fittings such as switches, ceiling roses, pendent, regulators, sockets, bell push, bell, light fittings etc. removing serviceable materials to store for keeping in safe custody for reuse at site or for taking credit (Credit shall be made as per Schedule of credit), removing rubbish from the site and making good all disturbed surfaces of walls, floors etc. to match with existing surfaces, complete all as specified and directed.

M&L in replacement for point wiring for one light/fan/bell point controlled by one switch complete with 1.5 Sqmm multistranded FRLS PVC insulated unsheathed fire retardent copper conductor cable 1100 volts grade in and including non metallic rigid PVC heavy duty concealed conduit with wall thickness not less than 1.8mm including conduit accessories like bends, tees junction boxes etc fixed concealed/recessed in wall or ceiling etc including 1.5 Sqmm single core FRLS PVC green insulated unsheathed multi stranded copper conductor 1100 Volts grade as earth continuity wire connected to earth dolly including sunken steel boxes zinc oxide painted of suitable size and wall thickness not less than 1.8mm complete all as specified and directed

All as per item No 102 above but for One light point controlled by two 2-way switches 230 Volts

All as per item No 102 above but forOne 5 pin socket out let 5/6 Amps on same boards.

Description all as per Srl item No. 102.00 here-in before but with 2.5 sqmm FRLS copper cable insulated for 3/5 pin 5/6 amp multipurpose outlet including 2.5 sqmm FRLS PVC insulated copper wire for earth continuity on independent boards complete all as specified and directed

All as per Srl item No. 102.00 here-in before but with 4 sqmm FRLS copper cable insulated for 3/5 pin 15/16 amp multipurpose outlet including 4 sqmm FRLS PVC insulated copper wire for earth continuity on independent boards complete all as specified and directed

All as per Srl item No. 102.00 here-in before but with 4 sqmm FRLS copper cable insulated for metal plug top geyser outlet including 4 sqmm FRLS PVC insulated copper wire for earth continuity on independent boards complete all as specified and directed

S&F for Switch piano flush button, single pole, one way, 5/6 Amps, 240 Volts AC with polycarbonate body, complete all as specified and directed.

S&F for Switch piano flush button, single pole, two way, 5/6 Amps, 240 Volts AC with polycarbonate body, complete all as specified and directed.

S&F for Switch piano flush button, single pole, one way, 15/16 Amps, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F for socket out let 6 pin 5/6 and 5/16 amps multipurpose 2 in 1 flush type, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F for socket out let 5 pin flush type 5/6 amps multipurpose 2 in 1 flush type, 240 Volts AC with polycarbonate body, complete all as specified and directed.

S&F for fan regulator electronic mini fan stepped type polycarbonate body, suitable to control speed of fan from 0 to 100% and connecting electrically, complete all as specified and directed.

S&F for lamp holder with lamp holder batten type polyarbonate body with back plate for batten fitting fixing with proper round block with and including 9 Watts ,230 V retrofit type LED lamp complete all as specified and directed.

S&F for ceiling rose, surface bakelite, 2 to 3 terminals, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F "in replacement" sheet metal enclosure MCB distribution board, double door, single pole & neutral 240volts 08 way with IP-54 IK-09 protection complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification, complete all as specified and directed.

S&F "in replacement" MCB single pole, 240 Volts, 5-32 Amps with repturing capacity 10 KA 'B' Curve complete all as specified and directed.

S&F "in replacement" MCB single pole and neutral, 240 Volts, 40-63 Amps with repturing capacity 10 KA 'C' Curve complete all as specified and directed.

M&L for submain wiring with two single core FRLS PVC insulated cable 6 sqmm (nominal dia) copper conductor (multistrand) and drawing in and including PVC concealed conduit pipe, ISI marked including 6 sqmm multistranded copper conductor FRLS PVC green insulated unsheathed cable for earth continuity, including taking down existing submain wiring complete all as specified and directed. Note : Three runs of wire shall be measured as one unit.

S&F in replacement of surface mounted 1x20 Watt LED tube light fittings (4 feet long), prewired, decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, enviornmental friendly, energy saving efficient ready to use pack 20 Watt LED 6500 K and making connection using 3 core, 0.50 sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc, complete all as specified and directed.

S&F in replacement of surface mounted 1x10 Watt LED tube mirror type light fittings (2 feet long), prewired, decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, enviornmental friendly, energy saving efficient ready to use pack 20 Watt LED 6500 K and making connection using 3 core, 0.50 sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc, complete all as specified and directed.

Supply & Fixing in replacement for LED light fitting 1x9x/1x10w bulk head luminares incl LED light driver holder connecting up to three core flexible copper conductor cable of suitable size.

Supply, fixing and testing in replacement of 25W energy saving LED Street Light luminaire. IP 67, AC 230 volts, LED Street Light shall be made up of Pressure Die Cast aluminum housing with black epoxy polyester powder coating for long life and toughened glass visor fitted in frame, secondry optical lens for superior light distribution efficiency 100Lm/W making connections with street light/ building security light box or OH line using PVC insulated and sheathed three core multi stranded copper conductor cable of size 1.5 Sqmm including suitable size of brackets and light grade pipe for maintaining of fittings complete all as specified and directed.

Note for srl item No 119 to 122 above 1. Driver shall be potted anti-vibration types. 2. LM-79 and LM-80 test report with 1 Lakh burning hours LED life from NABL lab shall be provided. 3. CRI (Colour Rendering Index) of fixture shall be > 70. 4. CCT (Colour Co-related Temperature of fixture shall be 5700K + 500 K. 5. System Lumen Efficacy shall be > 100 Lm/W. 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. 2 years guarantee shall be provided by contractor supported by OEM covering all parts of luminaire. 8. Lenses shall be Modular Type. 9. PCB used shall be MC PCB type. 10. The defect liability period of LED light shall be 02 years from the certified date of completion & the contractor shall replace/repair the defective fitting within 07 days after handing over to contractor for replacement/repair. 11. CA No. shall be written on each fitting before installation. 12. The name of manufacturer to be embossed on the fitting. 13. The fittings shall have arrangement so that maintenance required, if any can be carried out from Top cover.

S&F "in replacement" of sheet metal enclosure vertical type (VTPN) distribution board double door, triple pole & neutral 415 volts 4 way degree of protection IP-65 DBs TPN suitable for MCCB as incommer and as outgoing MCB, 415 Volts incl MCCB 415 V 63 Amp 16 KA as incomer and 16 Nos MCB SP of cap upto 63 Amp as a outgoing complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surface to match with existing specification, complete all as specified and directed.

M&L for earthing complete with galvanised GI earth plate electrode of size 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25 Mtr deep below normal ground level) with top edge of earth plate not less than 1.5 Mtr below normal ground level, connected to galvanised earth lead wire 4mm dia by means bolt, nuts, check nuts and washer made of galvanised iron or steel including earth work in any type of soil, charcoal dust and salt layers 15cm thick all around the earth plate as shown in electrical plate No. 03 of SSR Part-I 2009 including 20mm bore GI watering pipe 'medium grade' with funel and wire mesh and 15mm bore GI protection pipe 'light grade' from earth pit to main board including PCC pit in cement concrete 1:2:4 type B-2 (using 40mm graded stone aggregate) and including angle iron frame of size 40x40x3mm with hold fast embeded in PCC, RCC pit cover with suitable handle and earth work and removal of surplus soil to a distance not exc 50 Mtr, complete all as required at site and directed.

Supply and laying in trenches or fixed to wall/pole or passing through ducts or pipe, cable LT 1100 volts grade heavy duty, XLPE insulated , armoured heavy duty electric cable , with aluminium conductor of size 25 Sqmm x 3.5 core complete all as specified and directed. Note:- Excavation and earth work, sand cushioning, brick cover and protection pipe etc. shall be measured and paid for separately.

Excavating in trenches in any type of soil, n. exc. 1.5 m wide and n. exc. 1.5 m in depth, for laying cables foundation, etc. or for shafts, wells, cess pits, manholes, pier holes, etc n. exc. 10 sqm on plan and n.exc 1.5 m in depth and getting out complete all as specified and directed.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25 cm complete all as specified and directed.

Removing excavated material (soil) n.exc. 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed.

Sand cushioning for cables 8cm below the cable and 15 cm above the cable complete all as specified and directed.( Punned thickness shall be measured for payment)

M&L for brick protection with sub class 'B' old size brick well burnt laid flat for cable protection abutting each other laid dry with width equal to length of brick complete all as specified and directed.

S&F in replacement of GI tubing light grade 50 mm bore cut to size and fixed along the pole for cable protection including clamp 02 Nos of size 25x4 mm, nut bolts , washers etc all as required at site complete all as specified and directed.

S&F "in replacement" MCB single pole and neutral, with a two pin and earth plug and socket with one single pole MCB 20 Amps complete all as specified and directed.

Dismantling and taking out burnt winding by cutting, cleaning slouts and re-winding of AC ceiling fan motor1200mm/1400mm of any make of fan with super enameled heat resistant copper winding wire of existing gauge & nos of turns including, sleeve work, varnishing with E class insulation, greasing, threading, connection with flexible wire 0.472 mm copper wire upto connector block and re-assembling and testing for 4 Hrs after repair complete all as specified and directed. (Repairs will be measured and paid for separately under respective items):- Notes :- (i) Fan shall be collected by the contractor from MES store yard at thier own arrangement. (ii) Motor shall be wound with machine only and repair of fan inside complex / office of GE (S) Mamun. (iii) Khaitan/RPG/KEI or equivallent make super enameled copper winding wire shall only be used. (iv) Rates are deems to be included cost of repair /servicing & replacement of minor spare part i.e. blade screws, capacitors clumps terminal connection , split pin spring washer etc.

Replacement of old unserviceable gun metal bush of ceiling fan complete all as specified and directed.

Replacement of old unserviceable capacitor AC 415 volts 2.5 mfd oil filed ISI marked complete all as specified and directed.

Replacement of old unserviceable ball bearing of suitable size as per existing make and size of exhaust fan/wall mounted Fan complete all as specified and directed.

Servicing of ceiling fans of capacity 1200/1400mm including taking down from site , dismantling, cleaning, greasing/oiling of bush and bearings, replacement of set of split pins, cotter pins, blade screws, cup of both side and refixing to the existing site after servicing complete all as specified and directed. (Unserviceable parts if any will be measured and paid seperately). Note:- Contractor will deployed one elect & one helper for servicing of fans against srl item no 13 & 14 at site on all working day for the period of contract.

Replacement of old unserviceable fan blades as per existing shape, colour and design suitable for 1200mm sweep ceiling fan of any make complete all as specified and directed.

Dismantling and Re-winding of exhaust fan/industrial wall mounting fan/pedstral fan motor 250-380mm sweep any make of fan with super enameled heat resistant copper winding wire 31 SWG to 34 SWG including cutting and getting out old brunt winding, sleeve work, varnishing with E class insulation greasing, threading, connections with twin core copper flexbile wire of size 23/0.0076mm of length not more than one mtr with each fan complete all as specified and directed. Notes:- (i) Exhaust Fan/pedestal fan shall be collected by the contractor from MES store yard at thier own arrangement. (ii) Motor shall be wound with machine only. (iii) Khaitan/RPG/KEI /RR or equivallent make super enameled copper winding wire shall only be used. (iv) Exhaust fan are deems to be included cost of repair /servicing & replacement of minor spare part i.e. body screws, capacitors clumps , clips etc.

Removing old paint by scraping with sand paper including washing and filling cavaties with filter and applying two coats of painting to ceiling fan 1200-1400mm sweep at workshop with heat resistant synthetic enamel paint by spray painting incl, writing MES No on the ceiling fans as directed. Note:- Paint qaulity and colour shall be get approved from GE.

Replacement of old unserviceable outer body of ceiling fan (bottom and uper cover plate incl all fitments such screws, gasket cover canopy of both side etc complete all as specified and directed.

Replacement of existing unserviceable canopy top & bottom of ceiling fan as per existing size & shape complete all as specified and directed.

Replacement of existing unserviceable shutter and lover of exhaust fan as per existing size & shape complete all as specified and directed.

Replacement of existing unserviceable MS fan blade of exhaust fan as per existing size & shape complete all as specified and directed.

M&L for lathe work incl re-alignment to rotor, stater sloter, cleaning welding , bracing and polishing etc and refixing after repair and testing complete all as specified and directed.

M/S NARESH KUMAR SHARMA

surjit enterprises

M/S HIMANSHU BUILDERS

Bidder Name

surjit enterprises

Abrol construction co

M/S NARESH KUMAR SHARMA

M/S HIMANSHU BUILDERS