Special repair to Building No T 136 and T 137 of 30 Independent Reconnaissance and Observation Flight at Partap Pur under GE Partapur

Amount

Demolition of unreinforced cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level).

M&L 75 mm thick PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) in floorings plinth protection including finishing the surface even and smooth without using extra cement.

M&L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound

Dismantling floor hearth or wall tiling including cement mortor bedding but not backing, removing serviceable tiles to stores and rubbish off premises, complete all as specified and as directed.

M & L PCC 1:2:4 type B-1, 25 mm thick using 12.50 mm graded stone aggregate as in flooring surface finished even & smooth without using extra cement.

M&L 15 mm thick screed bed or bedding layer of cement mortar for laying floor finish in CM 1:6

M&L non skid coloured ceramic tile 7 to 8 mm thick (square/rectangular) are of each tile exc 0.11 Sqm but not exc 0.18Sqm , in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match.

Supply and fixing in repair laminated wooden flooring in size 1227mm x 197mm x 8mm thick, including skirting, floor breakers etc complete all as sper manufacturers instruction with a layer of foam backing complete all as specified and directed.

Dismantling wall and ceiling board (fibre, pulp, insulation etc) or insulation board/slabs/ blanket any thickness including cover filllets.

Dismantling timber framed in fillets,rails, posts rafters,purlines, etc under 40 sq cm in section.

M&L Veneered decorative plywood 6 mm thick, grade 1 (with BWR, resin) with decorative face on only one side fixed with nails as in Ceiling to timber frame work complete all as specified. (Including dismantling and refixing of same electic wiring and points)

M&L Veneered decorative plywood 6 mm thick, grade 1 (with BWR, resin) with decorative face on only one side fixed with nails to timber frame work as in walls complete all as specified.

M&L Veneered decorative plywood 9 mm thick, grade 1 (with BWR, resin) with decorative face on only one side fixed with nails to timber frame work as in walls complete all as specified.

M&L second class Hardwood plain filllets, rectangular in section, clean swan, secured with nails exc 13 and n.exc 25.

M&L second class Hardwood plain fillets, rectangular in section, clean swan, secured with nails exc 3 and n.exc 6.

S & F GI frame work of size (605 x 605) mm for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre /nnintermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, Hangers 6 mm dia. GI. (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia. 40 mm long complete all as specified.

M&L 6mm thick exposed metal framed ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600 mm grid ( frame work for ceiling shall be measured and paid seperately).

Dismantling of plain of corrugated steel sheeting any gauge, thickness including Nainital or similar pattern roof covering, complete all as specified and directed by Engr-in-charge.

S&F Galvanised MS sheeting of 0.63 mm thick corrugated ISI Marked and made of shakti with two corugation side laps and fixed with J hookes two framed work with PVC and steel washers as in roof & wall all as spd and as drected by Engr-in-Charge .

S&F Plain, galvanised, mild steel sheeting of 0.63 mm thick, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 all as spd and as drected by Engr-in-Charge .

Preparation of new steel surfaces of any description over 10cm in width or girth, not otherwise described, and applying two coats of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

M&L complete removal of existing treatment and applying two coats of synthetic enamel paint with camaflogue design over a coat of red oxide primer on steel surfaces, complete all as specified and directed by Engr-in-Charge.

M&L for wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed by Engr-in-Charge.

Taking down Chowkhats or frames exc 1.5 sq. m but n exc 4 sq. m each (without taking off shutters from frame).

Taking down Chowkhats or frames not exc. 1.5 sq. m each (without taking off shutters from the frames) .

S&F plain, solid, straight chowkats of second class soft wood and frames, wrough, framed rebated on the solid, rounded or chemfered, put together with glue pinned at joints .

S & F 35mm thick, 2nd class HW, plain framed, panelled shutter (one panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified .

M&L for preparation of new surface painting to wood or wood based new or previously untreated surface of any description,over 10 cm width or girth and applying two coat over a coat of pink primer all as specified and directed.

M&L for frame work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete drilled ofr fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel, sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete .

M&L for steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded.

M&L for Mild Steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up mitred angles, etc. as require all as specified and directed by Engr-in-Charge.

Preparation of new steel surfaces of any description over 10cm in width or girth, not otherwise described, and applying two coats of synthetic enamel paint with camaflogue design over a coat of primer complete all as specified and as directed by the Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads.

S&F 4.00mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each panel.

S&F 150 mm Mild steel, semi-barrel tower bolt, open cover, with sheet pressed barrel, stove enamelled black with bright bolt and fixed.

S&F 200 mm Mild Steel, sliding door bolts plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed.

S&F 125mm Mild steel pressed handles, oval type, stove enamelled black.

S&F Aluminium, anodised, barrel tower bolts,150mm, of extruded section and fixed .

S&F 200 mm Aluminium alloy, anodised, sliding door bolt with hasp and stapple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed .

S&F 125mm Extruded aluminium alloy handles, fabricated type. Anodised.

S&F 100 mm long butt hinges medium weight cold rolled MS and fixed all as specified.

S&F 75 mm long butt hinges medium weight cold rolled MS and fixed all as specified.

S&F 30cm long hold fast conforming to Fe.290. Gde-E-165 of Sectiion 25x3mm.

Taking down unserviceable aluminium/copper point wiring (light, fan, socket or power) incuding fixtures and fittings such as switcthes, ceiling rose, pendents regulators, sockets etc for taking out of credit and making good complete all as specified and directed by Engr-in-charge.

Taking down light fitting any type complete all as specified and directed by Engr-in-charge.

Taking down of existing Sub main wiring any size complete all as specified and directed by Engr-in-charge.

Taking down of MCB DB 8way/12way and making good of wall complete all as specified and directed by Engr-in-charge.

Taking down of MCB DP /Single pole complete all as specified and directed by Engr-in-charge.

M&L Point wiring with 1.5sqmm (nominal area) copper conductor FRLS cable (multi-stranded) PVC insulated and unsheathed electric cable 1100 volts cable and including PVC casing and caping suitable size (as per conductor run) with all fittings and accessories and including PVC insulated, unsheathed electric cable 1100 volts 1.5 Sqmm (multi-stranded) copper conductor single core green colour) cable as continuous earth wire connected to common earth dolly including 50mm deep box made out of 2nd class hard wood board of suitable size and shape and other boxes for mounting light fittings etc covered with 3mm thick plastic laminated sheet (Make- Hylum) Complete all as specified and directed by Engineer-in-Charge.

(a) One light/fan point controlled by one, one way switch 6 amps.

(b) One 5 pin, 5 Amp switch socket out let on the same board with other switches.

(c) One 5 pin, 5 Amp switch socket out let on the independent board.

M&L point wiring for power point with 4.0 sqmm (nominal area) copper conductor FRLS cable ( multi-stranded) PVC insulated and unsheathed cable conductor 1100 Volts drawn through rigid PVC casing capping of suitable size (ISI Marked) (Make - Hylum) including 50mm deep box made out of 2nd class hard wood board of suitable size and shape and other boxes with 3.0mm thick plastic laminated sheet cover (Make - Hylum) for 5pin socket outlet 15 Amp on independent board with 2.5 sqmm (nominal area) FRLS copper conductor cable (multi-stranded) PVC insulated and unsheathed (green Colour) with colour code earth wire to common earth dolly. Complete all as specified and directed by Engineer-in-Charge.

M&L switch piano flush type, 5 Amps, single pole, one way complete all as specified and directed by Engr-in-charge. Make : Anchor/Cona/Key.

M&L switch piano flush type, 15 Amps, single pole, one way complete all as specified and directed by Engr-in-charge. Make : Anchor/Cona/Key.

M&L socket outlet, flush type, 5 pin, 5 Amps, multipurpose complete all as specified and directed by Engr-in-charge. Make : Anchor/Cona/Key.

M&L socket outlet, flush type, 2 in 1, 3 pin, 5 and 15 Amps complete all as specified and directed by Engr-in-charge. Make : Anchor/ Cona/Key.

S&F ceiling rose, surface bakelite, size as per relevant IS, three terminals complete all as specified and directed by Engr-in-charge. Make : Anchor / Key / cona.

S&F MCB DB sheet enclosure single pole and neutral 240V with 100 Amp suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete confirming to IP 42/43 without MCB and with enclosure blank plates for unused way suitable for 12 way complete all as specified and directed by Engr-in-charge. Make : L&T/Schneider/Legrand/Hager

S&F in repair MCB, single pole & neutral, 240 Volts (16 to 40) Amps,10Ka complete all as specified and directed by Engr-in-charge. Make : L&T/ Schneider/Legrand(lexic)/Hager

S&F in repair MCB, single pole, 240 Volts (05 to 32) Amps,10Ka complete all as specified and directed by Engr-in-charge. Make : L&T/Schneider/ Legrand/Hager

S&F decorative ultra slim polycarbonate LED light fitting 1x22 watt surface mounted with accessories prewired including 1x22 watt LED tube connecting up with twin core twisted flexible copper conductor cable 1.0 sqmm complete all as specified and directed by Engr-in-charge. Make : havells cat part no LHEXBLP7PN1W022 or equivalent in CG/Bajaj/wipro.

S&F recessed mounting False ceiling (2x2 feet) LED luminaire 36 watt 230 volt white powder coated CRCA housing, luminaire with glare free uniform illumination and connecting with copper conductor cable complete all as specified and directed. Make: Crompton cat part no. LCTLSNE-24-FO-CDL or equivalent in wipro/bajaj/havells.

M & L for wiring with two single core 6.00 sqmm stranded copper conductor PVC insulated and unsheathed cable ISI marked in 25 mm dia, medium grade, PVC casing and capping main connection including 4 sqmm PVC insulated unsheathed copper conductor ISI marked as earth wire complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6mm thick burried directly in ground not less than 2.25m deep below normal ground level (with the top edge of the plate not less than 1.50 m below the normal ground level) connected to GI earth wire 4 mm by means of GI bolts, nuts, check nuts and washers of GI all as shown in electrical plate No.3 of SSR Part-I connected to earthing test point with and including necessary excavation and earth work in any strata PCC pit 1:3:6 type C-1, 20mm bore medium grade GI pipe for watering 15mm bore light grade pipe for GI wire protection and funnel including 40mm thick RCC slab cover and testing on completion all as specified and as directed.

S&F lamp holder, PVC polycarbonate type with back plate suitable for batten fitting complete all as specified and directed by Engr-in-charge. Make : Anchor/Cona/Key.

SONAM TUNDUP

H R CONSTRUCTION

M/S BHAT ENGINEERS

M/S SONAM RIGZIN

osho traders

M/S LIBE & CO

M/S ABDUL SAMAD MIR