NIT NO:- 07/RMC/ZONE 08/2026 RAIPUR DATED– 24.04.2026

OFFICE OF THE MUNICIPAL CORPORATION RAIPUR DIST - RAIPUR(C.G.)

Name of work : Construction of bhawan second phase kota housing board colony near mangal bahwan

Ward - Ramkrishna Paramhans Ward-

Estimate as Per PWD building S.O.R. 2015 & Electrical 2020

S.No I.No. Item No Length Breadth Ht/Dth Quantity Rate unit Amount

1 1.1 Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff upto 1.5 m lift and lead upto 50m (at least 5m away from the excavated area), including dressing and leveling of pits.

1.1.1 In all types of soils.

2 1.26 Carriage by mechanical transport upto 5 km lead:

Qty Of Excavated item 126.30 111.00 cum 14019.30

3 3.1 Providing and laying nominal mix plain cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work.

3.1.2 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size).

4 3.2 Providing and laying nominal mix reinforced cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work. (Note :Excess/ less cement used as per design mix is payable/ recoverable separately)

3.2.1 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size).

Column Footing 26 1.50 1.50 0.25 14.63

Column Upto Plinth Beam 26 0.20 0.40 0.70 1.46

5 3.12 Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire in foundation and plinth all complete:

3.12.1 Thermo-Mechanically treated bars FE 415

Taking 60Kg Per Cum Of Concrete 6065.36 54.50 kg 330561.98

6 2.1 Providing and fixing form work including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for:

2.1.1 Foundations, footings, bases of columns plinth beam, curtain wall in any shape and size and all type of wall below plinth level.

Column Upto Plinth Beam

Plinth Beam 2 x 4 10.00 0.30 24.00

2.1.5 Columns, Pillars, Piers and likes- rectangular or square in shape

For First Floor 2 x 10 0.20 3.10 12.40

2.1.8 Beams, lintels, cantilevers & walls

Lintel Beam 4 x 2 10.00 0.30 24.00

2.1.7 Suspended floors, roofs, access platform, balconies (plain surfaces) and shelves (cast in situ)

7 7.5 Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in:

7.5.4 Cement Mortar 1:6 (1 cement : 6 coarse sand)

Below Plinth 4 10.00 0.20 0.40 3.20

Above Plinth Beam

Parapet Wall 2 10.00 0.20 1.00 4.00

Deduction For Opening -3 1.20 0.20 2.80 -2.02

8 11.2 Providing and making 12mm thick cement plaster of mix:

11.2.3 In Cement Mortar 1:5 (1 cement : 5 fine sand)

Deduction For Openinng -3 10.00 3.10 -93.00

9 11.3 Providing and making 15mm thick cement plaster on the rough side of single or half brick wall of mix:

11.3.3 In Cement Mortar 1:5 (1 cement : 5 fine sand)

Under Side of Ramp 4 5.00 1.20 24.00

10 11.1 Providing and making 6mm thick cement plaster of mix:

11.1.2 In Cement mortar 1:4 (1 cement : 4 fine sand)

11 9.13 Providing and fixing steel door/ window with M.S. sheet 1mm thick, frame of angle iron, diagonal braces of angle/ flat iron of suitable size, 3.00 mm M.S. gusset plates at junctions and corners, all necessary fittings complete including applying a priming coat of red oxide zinc chromate primer.

Main Door 3 x 100 Kg per nos 300.00

Window 10 x 50kg per Nos 500.00

12 9.15 Providing and fixing M.S. grill of approved pattern made of M.S. flats or square or round bars welded to steel frame of windows etc. including applying a priming coat welded to frame with all necessary fitting complete including applying a priming of red oxide zinc chromate primer.

Taking LS Qty For Window And Ventilation 300.00 67.50 kg 20250.00

13 14.5 White washing with lime to give an even shade.

14.5.1 On new work (Three or more coats)

Qty Same As 12mm + 6mm Plaster 714.60 9.40 sqm 6717.24

14 14.13 Providing and applying 2mm thick ready mix exterior grade approved make putty (like Birla wall care, Alltek Superfine W/R of (NCL), Asian, ICI, Nerolac, J.K. wall putty) on walls to make the surface smooth and even.

Qty Same As 12mm + 6mm Plaster 714.60 94.50 sqm 67529.70

15 14.15 Painting exterior surface with ACRYLIC SMOOTH exterior paint of required shade as per manufacturer's specifications to give protective and decorative finish including cleaning washing of surface etc. complete with:

14.15.1 On new work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Qty Same As 12mm + 6mm + 15mm Plaster 1102.44 56.00 sqm 61736.64

16 14.14 Finishing walls with water proofing cement paint of required shade to give an even shade.

14.14.1 On new work (Two or more coats applied @ 3.84 kg/10 sqm)

Qty Same As 15mm Plaster 387.84 46.00 sqm 17840.64

17 12.12 Providing and laying vitrified floor tiles with soluble salt printing, of size 600x600mm with water absorption less than 0.5% and conforming to IS : 15622 of approved make, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.

Steel work in tubular (round, square or rectangular hollow tubes etc.) structure in built-up sections, trusses and frame work including cutting, hoisting, fixing in position upto a height of 5m above plinth level, consisting of columns trusses, roof and bottom purlins, base plate, holding down bolts, wind ties bracing (if required), bolts, nuts and washers for fastening etc. complete with applying a priming coat of red oxide zinc chromate primer.

Electric resistance or induction butt welded tubes Grade-250 400.00 88.50 kg 35400.00

Supply and fixing of precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm +/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Supplying, filling, spreading & leveling stone boulders/ Gravels/ Coarse sand, in recharge pit, in the required layers and thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. (excavation of pit will be paid separately).

Stone boulders of size range 5 cm to 20 cm, in recharge pit 1 5.00 5.00 0.20 5.00 cum 806 4030.00

Gravels of size range 5 mm to 10 mm, over the existing layer of boulders 1 5.00 5.00 0.20 5.00 cum 863 4315.00

Coarse sand of size range 1.5 mm to 2 mm over existing layer of gravel 1 5.00 5.00 0.20 5.00 cum 471 2355.00

total 2192794.62

Add 5% For Water Supply 109639.730765329

Add 9% for electrification, sanitary & rain water harvesting 197351.515377593

Say Amount - 25.00 lakhs

Technically Sanctioned for Rs . . . . . . . . . .

Sub Engineer Assistant Engineer Executive Engineer

Municipal Corporation Municipal Corporation Municipal Corporation

Raipur ( C.G. ) Raipur ( C.G.) Raipur ( C.G. )

S.No I.No. Item Quantity Rate Amount

1 1.1 Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff upto 1.5 m lift and lead upto 50m (at least 5m away from the excavated area), including dressing and leveling of pits.

1.1.1 In all types of soils. 126.30 185.00 23365.50

2 1.26 Carriage by mechanical transport upto 5 km lead:

3 3.1 Providing and laying nominal mix plain cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work.

3.1.2 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size).

4 3.2 Providing and laying nominal mix reinforced cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work. (Note :Excess/ less cement used as per design mix is payable/ recoverable separately)

3.2.1 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size).

5 3.12 Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire in foundation and plinth all complete:

3.12.1 Thermo-Mechanically treated bars FE 415

6 2.1 Providing and fixing form work including centering, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for:

2.1.1 Foundations, footings, bases of columns plinth beam, curtain wall in any shape and size and all type of wall below plinth level.

2.1.5 Columns, Pillars, Piers and likes- rectangular or square in shape

2.1.8 Beams, lintels, cantilevers & walls

2.1.7 Suspended floors, roofs, access platform, balconies (plain surfaces) and shelves (cast in situ)

7 7.5 Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in:

7.5.4 Cement Mortar 1:6 (1 cement : 6 coarse sand)

8 11.2 Providing and making 12mm thick cement plaster of mix:

11.2.3 In Cement Mortar 1:5 (1 cement : 5 fine sand)

9 11.3 Providing and making 15mm thick cement plaster on the rough side of single or half brick wall of mix:

11.3.3 In Cement Mortar 1:5 (1 cement : 5 fine sand)

10 11.1 Providing and making 6mm thick cement plaster of mix:

11.1.2 In Cement mortar 1:4 (1 cement : 4 fine sand)

11 9.13 Providing and fixing steel door/ window with M.S. sheet 1mm thick, frame of angle iron, diagonal braces of angle/ flat iron of suitable size, 3.00 mm M.S. gusset plates at junctions and corners, all necessary fittings complete including applying a priming coat of red oxide zinc chromate primer.

12 9.15 Providing and fixing M.S. grill of approved pattern made of M.S. flats or square or round bars welded to steel frame of windows etc. including applying a priming coat welded to frame with all necessary fitting complete including applying a priming of red oxide zinc chromate primer.

13 14.5 White washing with lime to give an even shade.

14.5.1 On new work (Three or more coats)

14 14.13 Providing and applying 2mm thick ready mix exterior grade approved make putty (like Birla wall care, Alltek Superfine W/R of (NCL), Asian, ICI, Nerolac, J.K. wall putty) on walls to make the surface smooth and even.

15 14.15 Painting exterior surface with ACRYLIC SMOOTH exterior paint of required shade as per manufacturer's specifications to give protective and decorative finish including cleaning washing of surface etc. complete with:

14.15.1 On new work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

16 14.14 Finishing walls with water proofing cement paint of required shade to give an even shade.

14.14.1 On new work (Two or more coats applied @ 3.84 kg/10 sqm)

17 12.12 Providing and laying vitrified floor tiles with soluble salt printing, of size 600x600mm with water absorption less than 0.5% and conforming to IS : 15622 of approved make, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.