SPL REPAIR TO QTR NO 20/A/1, 20/A/2, 10/C/1 AND 10/1/B HM MARG AND OTHER SANCTION MINOR WORK UNDER GE(EAST) LUCKNOW.

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thickness below and above ground level, complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches , pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

M & L for brick work using old size fly ash brick, straight or curved on plan exc 6m mean radius, built in CM (1:6), complete all as specified and directed.

M&L PCC 1:2:4, type B1 using 20 mm graded stone aggregate as in roof kerbs / benching / coving and roof padding over roof surfaces /sunken treatment etc rounded or chamfered on edges, complete all as specified and directed.

M&L for Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:4 mixed with water proofing compound (ISI marked) @ 200 ml per bag cement by weight of cement or as per manufacturer’s instructions, w/o using extra cement complete all as specified and directed.. Note :- Supply only water proofing compound shall be measured and paid for separately.

Providing and applying single component PU Magnum solvent base Pure polyurethane liquid membrane for the concrete roof surfaces in two coats @1.85kg/ sqm and mixing ratio of hardener and base is 95:05 and consisting of a coat of two component epoxy primer in ratio of 1:1 (one part of resin and one parts of hardner) at a consumption of 0.200kg/sqm The vital physical and chemical parameters shall be as under : Min Elongation at break of 500% as per ASTM D2370 and tensile strength of 3.0 N/mm2 as per ASTM D2370, Crack Bridging ability greater than 3mm as per C1305 ,Water Impermeability on coated concrete @7 bar as per DIN1048,Water vapor permeability 0.72 perms as EN ISO 7783-2 . The material shall be applied with brush and it should be tested according to EN 1504-2 as a coating for surface protection for concrete, complete in all respect as per the direction of Engineer-in-charge.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc, complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair face of brick work of walls, finished even & smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on fair face of brick work of walls, mixed with water proofing compound (ISI marked) @ 200 ml per bag cement by weight of cement or as per manufacturer’s instructions, finished even & smooth without using extra cement complete all as specified and directed. Note:- Supply only water proofing compound shall be measured and paid for separately.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound, ISI Marked complete all as specified and directed.

Complete removal of existing treatment from wall applying two coats of oil bond distemper over a coat of primer over a coat of wall care putty (2 mm thick) to make surface even and smooth, and complete all as specified and directed.

M&L for complete removal of exisiting finish/newly plastered surface (with mechanical sander machine) on walls and applying plaster of paris putty of min 1 mm thickness to prepare the surface even and smooth and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed. Note:- Paint to be applied with airless spray machine .

M&L for complete removal of existing treatment and applying three coats of of white wash on ceilling complete all as specified and directed.

M&L for complete removal of existing treatment and applying three coats of of white wash on walls complete all as specified and directed.

M&L for preparation of old painted surfaces of steel and iron work of any description over 10 cm width or girth and applying two coats of synthetic enamel paint, complete, all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for vitrified ceramic tiles 10mm thick (square/rectangular), light coloured (shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified and directed.

All as per description of serial item No 18 above but on vertical surface over & including 10mm thick screed bed in cement & sand mortar 1:4, complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8 mm thick (square/ rectanglar) area of each tiles exc 0.11 Sqm but not exc 0.18 Sqm as in floor over and including screed bed 15mm thick in CM 1:6 or beding layer for laying floor finishes etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed.

M&L for coloured, glazed, ceramic tiles 600X300X7mm thick but as on vertical surfaces such as skirting/dado over and including 10mm thick rendering in CM 1:4, complete all as specified & directed.

M&L for 18-20 mm thick granite (of any type) work (table rubbed & polished) in steps, jambs, pillars, window-cills, cooking platforms & like, over 15mm thick screed bed in cement mortar (1:6) including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite and rounding the edges and making holes for gas pipe as required , after dismantling of old granite complete all as specified and directed.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even w/o using extra cement complete all as specified and directed. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

Forming construction joints 30 mm deep x 10mm wide filled with sealing compound grade "A."complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings as original where required and pointing in cement mortar 1:3 for concealed water tubing etc. and making good, cutting not exc 10 cm girth in brick walls. complete all as specified and directed.

S&F in repairs galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.complete all as specified and directed.

S&F in repairs galvanized steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.complete all as specified and directed.

S&F in repair viterous china wash down water closet pan (Pedestal pattern) with 'P' or 'S' trap including connection to trap, flushing pipe, anti syphonage pipe and cistern and S& F WC seat cover closed pattern with flat bottom and cover with mild steel chromium plated or aluminised hinging device and finally making good disturbed surface of floor complete all as specified and directed.

S&F in repairs PVC valveless syphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified and directed.

S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified and directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including 40mm bore PVC waste fitting suitable for sink with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete, including taking down old unserviceable sink. complete all as specified and directed.

S & F for stainless steel kitchen plate rack of overall size 750 mm x 600 mm and 250 mm deep, with partitions for small/large plates etc made out of stainless steel 0.63 mm thick fixed with rawl plug and CP steel screws complete all as specified and directed.

S&F PVC connection 450 mm long suitable for 15 mm bore GI pipe including CP brass nuts on both sides, complete all as specified & directed.

S&F in repairs long body 15mm bore bib tap, fancy type, chromium plated, cast copper alloy, with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & directed.

S&F in repairs CP angle valve, fancy type long body for 15 mm bore pipe with capstan head long screwed shank including cp cover plate complete all as specified & directed.

S&F in repair 15mm bore fancy type two way CP Brass Bib taps with capston head, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed .

S & F in repairs CP brass center hole mixer (swan neck) for counter type wash basin for mixing hot and cold water screwed down for iron pipe and fixed for 15 mm bore pipe size complete all as specified and directed.

S&F in repair chromium plated brass wall mixer 2 in 1 (L-bend type) with hot and cold arrangement with cups suitable for 15mm bore pipe complete all as specified and directed.

S & F for 5 mm thick glass Corner shelf 300mm with chromium plated guard, fixed with brass screws and wooden/plastic cleats complete all as specified and directed.

S&F in repair sheet glass shelf assemble consisting of 5.5 thick sheet glass shelf 12cm wide with CP bracket gaurd & railing 60cm long complete all as specified and directed.

S&F in repairs CP brass tubular towel rail, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified and directed.

S&F in repair CP brass health faucet not exc 1.25 m long flexible tube including wall hook complete all as specified and directed.

S&F in repair soap dish, of stainless steel complete all as specified and directed.

S&F in repair toilet paper holder, brass chromium plated fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

S&F in repair PVC cabinet mirror bathroom box type complete all as specified and directed.

S&F in repairs brass chromium plated shower rose 125 mm size without swivel joint including fixing to steel pipe of 15mm bore or union complete all as specified and directed.

S&F 1000 Litre capacity Rotational moulded polyethylene water storage tanks, triple layered (cylindrical, vertical with closed top) hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe incl 20 mm ball valve high pressure of PTMT with apoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete after dismantling old RCC/PVC tank, complete all as specified and directed.

S&F 500 Litre capacity Rotational moulded polyethylene water storage tanks, triple layered (cylindrical, vertical with closed top) hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe incl 20 mm ball valve high pressure of PTMT with apoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete after dismantling old RCC/PVC tank, complete all as specified and directed.

S&F in repairs 20 mm bore gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

S&F in repairs 22-25 mm dia stainless steel curtain rod including brackets and fancy type finials, complete all as specified and directed.

Taking down eaves gutters and rain water pipes ( any size or pattern) incl all fittings , shoes, bends, swan neck etc. and removal to store complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including PVC holding clamps, complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including PVC holding clamps, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 75 mm PVC (SWR) floor trap, plain with CP grating, with or without hole including jointing with solvent cement complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend, any radius, complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend, any radius, complete all as specified and directed.

S&F 110mm PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction single (Single T) equal or unequal complete all as specified and directed.

S&F 75mm PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single (Single T) equal or unequal complete all as specified and directed.

S&F 110mm bore PVC (SWR) vent cowl, complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area exc 1.5 sqm but n.exc 4 sqm each, complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area not exc 1.5 sqm each, complete all as specified and directed.

S&F pressed steel frame for door with one or more rebates size 125x60mm including necessary fixing lugs, lock striking plates, hinges, hold fast etc, incl back filling with PCC 1:3:6 type C1 using 20 mm graded aggregates, complete all as spcefied and directed

S&F pressed steel frame for door with one or more rebates size 105x60mm including necessary fixing lugs, lock striking plates, hinges, hold fast etc, incl back filling with PCC 1:3:6 type C1 using 20 mm graded aggregates, complete all as spcefied and directed

S&F 32mm thick flush shutter solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S & F for 35mm thick factory made glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 (a) of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.

S&F PVC cabinet shutter as in Kitchen, Cup board, wardrobe etc with frame of min size 60mm x 44mm including shelves in required sizes at site made out of 18 mm thick one side decorative lamination & other side balancing lamination sheet & provision of shutter made out of 18 mm thick one side decorative laminated PVC sheet all required brackets stainless steel screw etc the panels shell be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bend finish including all necessary fitting as per site requirement and as per make and specification mentioned complete all as specified and directed. Note:- Density of PVC solid sheet should not be less than 575 kg/M3.

S&F magnet ball catcher for cup board shutters, complete all as spcefied and directed.

S&F 100mm size stainless steel fancy type handle, complete all as specified and directed.

S&F 150mm size stainless steel fancy type handle, complete all as specified and directed.

S & F for 100 mm long Hasp & staple, safety type, Stainless steel with mild steel hinges pin including bolt to hinges plate & fixed with screw, complete all as specified and directed.

S&F auto concealed hinges SS size 103mmx64mmx28mm suitable for cabinet and wardrobe complete all as specified and directed.

S&F PVC solid door frame of size 50x47mm made out of 5m plain coloured sheet reinforced with MS square tube complete all as specified and directed.

S&F for factory made soild PVC profiled panel door shutter 28mm thick with integral skin as frame & 3mm thick high pressure compact laminate on both side of approved colour as infill, with 'C type Gl or 40 x 20 x19 of MS pipe as stiffner & supplying & fixing in frame at site as per pecifications & drawing.complete all as specified and directed.

S&F butt hinges of size 100 mm medium weight, stainless steel ISI marked complete all as specified and directed.

S&F 200 mm long stainless steel tower bolts of extruded section (ISI marked) complete all as specified and directed.

S&F 100mm double legged door stopper of stainless steel with rubber base complete all as specified and directed. by Engr-in-charge.

S&F 300 mm long stainless steel sliding door bolts, fancy type, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed.

S&F mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed.

S&F in motice locks of brass, 4 lever, 100 mm size, vertical type complete all as specified and as directed.

S & F M.S. Framed work such as grills grating etc. with ends of bars sholdered and / or riveted into spikes, framed guard bars / railings complete all as specified and directed.

S&F powder coated(min thickness of powder coating 50 micron) anodised aluminum window shutter three track sliding type, section having frame size bottom with outer 92x45.5x1.5mm (section code 20617) , top and side 92x31.75x1.5 (section code 20831) & aluminum section of shutter top and bottom size 40 x 18 x 1.5 ( section code 20736) , interlock size 40 x 18x 1.45 (section code 20737), side/ middle size 40 x18 x1.55, (section code 20738) including necessary joining cleats, glazing clips rubber backing, anodised aluminum snap beading screw, anodised aluminum fitting complete as per site requirtement glazing by using 5mm thick plain sheet glass and ss wiremess of dia 0.36mm and aperture 1.4mm thick complete all as specified and directed.. Ref drg no celz/c-td/151 sheet no 1/1 & 2/2 . Note- 1. Glazed shutter glass thickness not less than 5mm and ss wiremess shutter with ss wiremesh as approved by GE is also included. No payment will be made separately. 2. No extra payment will be made for section profiles of higher sizes.

S&F powder coated aluminum ventilator ( louvers) shutter with 3.8 mm thick plain / tinted glass consisting of frame of size 63.5 x 44 and shutter sections weighing not less than 0.55 kg/m with locking arrangement as approved fixed including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings with stainless steel wiremesh of 0.36mm including necessary fixing arrangement complete all as specified and directed

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified and directed.

M & L Preparation of new steel or iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

S&F for stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with alluminium wire staples, (any welding work required will be included) complete all as specified and directed.

S&F in repair peg set of 6 brass fancy type,min length 600 mm complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed

M&L for precast RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in Chhajjas, cover slab, shelves and similar articles set in CM 1:4 complete all as specified and directed.

M&L for RCC 1:2:4 type B1 (using 20 mm graded aggrigate)as in slab,chajjas,beam etc and similar suspended works complete all as specified and directed.

Form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exc 200mm thick, flat rough finished surface of concrete complete all as specified and directed..

M&L for TMT bars 10mm dia and over cut to length, bent to shape required including cranking and binding with Mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Repair of Chajjas upto 2 stories by completly removing old broken plasters or pieces of concrete and dubbing out with cement mortar 1:4 or by cement concrete 1:2:4 (12.5 mm graded aggregate) incl necessary formworks and scaffoldings upto 2 stories and GI wire netting 0.90 mm dia and 12 mm mesh for propper bonding of concrete/ mortar and finally finishing the surface smooth and even w/o using extra cement and applying the finish matching from the neighbouring areas complete (plan area of chajjas to be measured).complete all as specified and directed.

S&F stainless steel kitchen plates fixed to lower mould of drawer of size 21"x20"x04" complete all as specified and directed.

S&F stainless steel cutlary having size 21"x20"x04" complete all as specified and directed.

S&F MS sliders of size 21" for facilatate to drawer slide on steel ball bearing ,fixed with screw/nut and bolts complete all as specified and directed.

S&F in repairs kitchen cabinet shutter with frame including shelves,drawer made of solid PVC Block board18/ 19 mm thick both sides decorative face having smooth outlet integral skin are made and shall be fixed to walls using required size sheet metal screw and solvent adhesive vertical and horizontal profile made of PVC 18/19mm solid board profile complete all as specified by manufacturer instruction complete all as specified and directed.

M&L for 75mm thick cement concrete type D-2, 1:4:8, as in sub base to floor,complete all as specified and directed.

M&L for 25 mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in floors complete all as specified and directed.

M&L for non skid ceramic (coloured) tiles of 7-8 mm (square or rectangular) area of each tile exceeding 0.18 sqm but n.exc 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match coloured tiles over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

S&F in repair Vitreous China wash hand basin under counter type oval shape of size 550x400mm including brackets, waste fittings, pvc waste pipe complete all as specified and directed.

S & F vitreous china pedestal pan EWC (Couple Closet Bowl) of size 370 x 640 x 760 mm including UF seat cover, hinges, S trap-220 mm, accessories set etc and vitreous china ware flushing cistern of complete all as specified and directed.

S & F in repairs CP brass center hole mixer for sink for mixing hot and cold water screwed down for iron pipe and fixed for 15 mm bore pipe size complete all as specified and directed.

S&F in repair long body 15mm bore fancy type bib tap of min weight 0.575 kg, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified & directed.

S&F in repair CP angle valve fancy type of min weight 0.575 kg, long body for 15 mm bore pipe with capstan head long screwed shank including cp cover plate fancy type complete all as specified and directed.

S&F in repairs towel ring 200 mm dia and made out of 8-10 mm dia hollow tubes superior quality complete all as specified and directed.

Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc for taking credit including making good the disturbed surfaces to match with the existing complete all as specified and directed.

Material and labour for one light / fan point controlled by one, one way switch 06 Amp wiring with 1.5 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sq mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall etc and making good to the disturbed surfaces to match the existing complete all as specified and directed.

All as per serial item No 113 here-in-before but one bell point controlled by one bell push, 06 Amp.complete all as specified and directed.

All as per serial item No 113 here-in-before but one, two way light point controlled by two, two way switches, 06 Amp.complete all as specified and directed.

All as per serial item No 113 here-in-before but one 3 pin, 06 Amp socket outlet point on independent board controlled by one, one way switch 06 Amp.complete all as specified and directed.

All as per serial item No 113 here-in-before but one 3 pin, 06 Amp socket outlet point on same board controlled by one, one way switch 06 Amp.complete all as specified and directed.

All as per Serial Item No 113 here-in-before but point wiring with 2.5 Sq mm single core FRLS cables and earth continuity wire of 2.5 Sq mm single core FRLS cable for one 3 pin 16 Amp socket out let point controlled by one, one way switch on independent board complete all as specified and directed.

S&F in replacement Switch Modular 6A single pole, one way, 1 module complete all as specified and as directed

S&F in replacement Switch Modular 16A single pole, one way, 1 module complete all as specified and as directed

S&F in replacement Socket, 6A - 2/3 pin combined 2 module complete all as specified and as directed

S&F in replacement Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and as directed

S&F in replacement Modular White cover plate with frame,12 module complete all as specified and as directed

S&F in replacement Modular White cover plate with frame,8 module complete all as specified and as directed

S&F in replacement Modular White cover plate with frame,3 module complete all as specified and as directed

S&F in replacement Modular White cover plate with frame,2 module complete all as specified and as directed

S&F in replacement Modular Metal flush box 12 module complete all as specified and as directed

S&F in replacement Modular Metal flush box 8 module complete all as specified and as directed

S&F in replacement Modular Metal flush box 3 module complete all as specified and as directed

S&F in replacement Modular Metal flush box 2 module complete all as specified and as directed

S&F in replacement Calling bell , AC, 230 Volts, single phase complete all as specified and as directed

S&F in replacement bell push , AC, 230 Volts, 2 module complete all as specified and as directed

S&F in replacement telephone socket 1 module complete all as specified and as directed

Supply and fix in replacement of decorative wall mounting type LED light fitting, 1 x 15 Watt, 230 Volt made up of Polycarbonate including shade, lamp holder, 9/10 Watts LED lamp B22 CDL etc and all accessories pre-wired including connecting up complete all as specified and directed.

Supply and fix in replacement of integrated LED bulk head fitting 10 Watt, 6500K with IP 65 protection comprises of high pressure die cast aluminium housing, polycarbonate cover, etc complete all as specified and directed.

Supply and fix in replacement LED tube light fittings 1200 mm,20 W higher energy saving decorative ultra slim square profile LED lighting fixture with extruded aluminum housing enviromental friendly, energy efficient complete all as specified and directed.

Supply and fix in replacement LED tube light fittings 600 mm, 10 W higher energy saving decorative ultra slim square profile LED lighting fixture with extruded aluminum housing enviromental friendly, energy efficient complete all as specified and directed.

Supply & fix LED in replacement wall/surface mounted down lighter, 12 W including electrical connection with PVC three core copper flexible wire & all necessary fixing accessories complete all as specified and directed.

Supply and fix in replacement ceiling rose, 6 Amp, 250 volt, AC, ISI marked with three equal size terminals and PVC / Polycarbonate insulated body of 50 x 25 mm size complete all as specified & directed.

Taking down carefully ceiling fan of any sweep complete with all accessories, dismantling blades and deposit in safe custody of AGE E/M Yard-II for BER procedure complete all as specified & directed.

Material and labour in replacement for sub main wiring with 10 Sq mm nominal cross sectional area,3 run single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 10 Sq mm nominal cross sectional area, single core r runs ( neutral and earth colour code wire), 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed.Note : 3 runs of 10 sqmm, 2 run of 10 sqmm earth and nutral conductor and 2 run of PVC conduit shall be measured as one unit length for

Material and labour in replacement for sub main wiring with 04 Sq mm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 04 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed.Note : 2 runs of 4 sqmm, 1 run of 4 sqmm earth and nutral conductor and 1 run of PVC conduit shall be measured as one unit length for

Supply and fix SRCD D Box 20 Amp with steel enclosure suitable for Geyser & AC protection to human from eletric shock due to direct and Indirect current as well as provide protection from overload and short circuit fault complete with MCB 20Amp after fixing making good surface with fine plastering, finishing and colouring with existing colour matching complete all as specified and directed.

M & L in factory made powder coated distribution board 4 way TPN DB Double door with metal double door (IP-43 protection IK -09) fabricated of CRCA sheet and fixed on wall and suitable for universal mounting and including 200 Amps bus bar, Neutral bar, Standard din rail,earth bar and cable ties for cable management, top and bottom removable gland plates with provn for MCB TPN and RCCB as incomer and 12 SP MCBs outgoing after fixing making good surface with fine plastering, finishing and colouring with existing colour matching complete all as specified and directed.

Supply and fix in replacement of MCB, SP, AC, 240 volt of 06 to 40 Amp capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Supply and fix in replacement of MCB, DP, AC, 240 volt of 32 Amp capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Material and labour for earthing complete with galvanised mild steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level steel earth plate connected with GI wire 04 mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15 mm bore light grade all as shown in elect plate No 3 on serial page No 497 of SSR part I - 2009 and connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150 mm thick around GI earth plate, GI pipe medium grade 20 mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40 mm thick in PCC 1:2:4 type B1 duly reinforced with MS Bars 6 mm dia at the rate of 75 mm centre to centre both way with 12 mm dia lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40 mm x 40 mm x 3 mm frame for pit cover including testing on completion complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) with remote oprated complete all as specified and directed. by Engr-in-Charge

S&F of exhaust fan single phase, 230/240 Volt heavy duty of size 300 mm sweep 1400 RPM including suitable louvers and making connection with twisted copper flexible wire 23/0.076mm complete all as specified and directed.

S&F exhaust fans, plastic body, ac, single phase, 230/240 v of size 250 mm sweep with louver and making connection with twisted copper flexible wire 23/0.076mm complete all as specified and directed.

Supply and fixing in replacement LED Bldg security light fitting LED 35 watt with SPD, PF not less or equal 0.9,epoxy coated cover sheet aluminium housing with heat resistant toughtened glass & IP 66 incl with bracket, clamps, nuts, bolts protection complete all as specified and directed and directed.

Cutting walls any type, making holes for fixing of exhaust fan of any size or sweep and making good surface with fine plastering, finishing and colouring with existing colour matching complete all as specified and directed

Taking down carefully Geyser of any type and capacity complete with all accessories, dismantling and refixing at same place with new PVC hot series connection pipe after finish of civil work complete all as specified & directed.

Taking down electric meter and refixing on same board after rewiring complete all as specified and directed.

Supply and fixing wall mounted fans complete with blades, and accessories, 230 V, 400 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. complete all as specified and directed. by Engr-in-Charge

Supply and fix PVC air freshner 250 mm sweep AC single phase, 230/240Volt 50 Hz with louvers and making connection from ceilling with twisted copper flexible wire 23/0.076mm complete all as specified and directed.

Supply and fix switch socket combenation piano flush type,06 Amp,single pole, 230 Volt complete all as specified and as directed

M/S Reliance Construction (BID ID -3136041)

QUALITY CONSTRUCTIONS CO (BID ID -3128069)

M/s Ramesh Chandra (BID ID -3128610)

M/s Durga Construction Company (BID ID -3128308)

m/s raghubar dayal (BID ID -3135090)