SPECIAL REPAIR TO BLDG NO. P 108 ( 04 X JCOS QTR) AND BLDG NO. 20, 21, 22 and 40 (MD MES CIV QTRS) AT SUBATHU UNDER GE KASAULI

Amount

Schedule 'A' Section - I

Dismantling plain or corrugated mild steel sheeting any gauge, thickness, including Nanital or similar pattern roof covering, complete all as specified and directed.

Supply and fixing of Pre-painted galvalume aluminuim zinc coating GI based corrugated steel sheet 0.50mm thick, conforming to IS-15961 of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws, complete, all as specified and as directed. Note- The sheets shall have (150 gm/sqm total on both sides) with super durable polyester quality paint of approved colour, suitable for exterior application conforming to IS-15965.

Supply and fixing of Pre-painted galvalume aluminuim zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws, complete, all as specified and as directed. Note- The sheets shall have (150 gm/sqm total on both sides) with super durable polyester quality paint of approved colour, suitable for exterior application conforming to IS-15965.

Dismantling timber in any position of unframed work as in fillets, rails, post, rafter, purlins , etc, under 40 Sqcm in section, complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise specially provided complete all as specified and as directed.

Supply and fixing mild steel, rolled sections as in main or cross beams, hip and jack rafters, purlin where connected to comman rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates conforming to grade Fe-410(Gde 250), complete all as specified and directed.

Supply and fixing welded steel wire fabric fixed to wood or steel members, weight exc 4 kg per square meter complete all as specified and as directed.

Supply and fixing, water storage tank 500 ltr capacity HDPE Triple layer, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut , ISI marked, screwed and suitable for iron pipe 20 mm bore,including taking down the unserviceable water tank and removing from site, complete all as specified.

Supply and fixing in repairs, brass valve high pressure with polythene float and flynut , screwed for iron pipe size 20mm bore, complete all as specified

Demolition of cement concrete (unreinforced), of any description and in any position, not otherwise specifically provided for, and removal of the rubbish/ demolished material outside defence land complete all as specified and as directed.

Material and labour for applying water proofing treatment to sunken slab comprising of the following specifications complete all as specified. (i) Cleaning of roof surface with mechanical means i.e. wire brush/air blower etc. and remove all loose /unsound material,dirt,dust etc. (ii) Providing and laying water proofing treatment of sunken portion of WCs, bathroom etc by applying cement slurry mixed with acrylic based polymer modified cementitous composit compound coating of make as approved in Technical Instruction 5/2003 (iii) First layer of cement slurry @ 0.488 Kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.253 Kg/Sqm of approved make and allowed layer to air cure for 04 hours. (iv) Second layer of cement slurry @ 0.244 Kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.126 Kg/Sqm and allowed layer to air cure for 04 hours followed with water curing for 48 hrs . (v) 200 micron thick polythene film pasted with the hepl of adhesive shall be provided over treatment .

item No. 11.00 (contd....) Note :- (i) Concrete for sunken slabs shall be mixed with WP compounds as per manufacture instruction. (ii) The slope of slab shall be 1:20 towards the corner of outer walls and GI pipe of 50-80mm dia ( Medium grade ) be inserted at corner projecting out side 20 cm . The sunken slab shall invariably rest on inverted beam from sides. (iii) 15mm plaster mixed with WP compound shall be provided while concrete is still green .If any leakage/dampness is seen in eiling exposed below then a proper treatment is given and again tested befoe passing for next stage. (iv) Joints of WC/Trap/Soil waste shall be properly sealed with sealing compound. (v) P/S traps and Nahani/Floor traps with long arm shall be provided as per latest instruction . (vi) Testing of all trap & joint and sunken slab shall be as per IS-1742 before filling and tilling of sunken slabs, including smoke test. (vii) The water proofing treatment shall be carried out by the manufacturer or his authorised applicators and contractor shall also provide 07 years Guranttee for water proofing treatment carried out in the work. Testing of all traps and joint and sunken slab shall be done as per IS-1742 before filling and tiling work.

Material and labour for 25mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as levelling course laid and compacted in slope, in floor complete all as specified and directed. Note- This item shall not be used where dismantling of tiles in flooring has been ordered.

Material and labour for PCC 1:5:10 type E-2, using 40 mm graded crushed stone aggregate as in filling in sunken floor, rounded or chamfered on edges complete all as specified.as directed .

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of steel reinforcement as required to facilitate demolition and removal the rubbish/ demolished material outside defence land, complete all as specified and directed.

Material and labour for providing reinforced cement concrete (design mix) M-25 (using 20mm graded mechanically crushed stone aggregate) in slabs supported on walls, beams and columns in floors, roof, landings, balconies, deck slabs and in shelves and the like complete all as specified and directed.

Material and labour TMT bars, 8 mm dia and above , cut to length, bent to shape required including cranking, binding spirally for hooping or column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

Use and waste of formwork to sides and soffits of roof beams, cantilever, bressummers ,lintels , shelves including supports and similar work for rough finished flat surfaces of concrete, complete all as specified.

Dismantling floor, hearth or wall tiling of any description (Ceramic/PCC/Terrazo) and any thickness, including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed..

Material and labour for premium quality, joint free, non skid, coloured ceramic 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm tiles, as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including cement screed bed 15mm thick in cement mortar (1:4) base, complete all as specified.

Material and labour for premium quality, glazed coloured ceramic tiles 300 x 450 x 7mm thick on vertical surfaces of walls including 10mm thick rough finished plaster in cement mortar (1:3) set jointed in neat cement slurry and pointed in coloured cement to match ,complete all as specified.

Demolition of stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar in floors, aprons, etc. removing the rubbish outside the defence land ,complete all as specified

Material and labour for 18mm thick granite (of any type) work (table rubbed and polished and moulding) in kitchen platforms over and including 15mm thick in cement mortar (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite, complete all as specified and as directed.

Material and labour for Rounding to edges of stone slabs any thick as in in steps, jambs, pillars, cooking platforms and likes complete all as specified and as directed.

Taking down chowkats or frames area exceeding 1.50 Square meter and not exceeding 4.00 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed.

Taking down chowkats or frames area not exceeding 1.50 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed.

Taking down shutters of any description exceeding 1.00 Sq.m but not exceeding 2.00 Sq.m each, from chowkhat and refixing in the same opening after erasing complete all as specified.

Resecuring or easing and adjusting without taking down Shutters of any description exc. 1 sqm each and not exc. 2 sqm each complete all as specified and as directed.

Supply and fixing factory made pressed steel frames of size 125 x 60 mm for doors fabricated from 1.25 mm thick sheet, with one or more rebate including necessary fixing lugs, hinges, lock strike plate, etc. and one shop coat of priming including plain cement concrete 1:3:6 type C-0 (using 12.5 mm graded mechanically crushed stone aggregates) in filling of door frame complete ,all as specified and as directed.

Supply and fixing factory made pressed steel frames of size 105 x 60 mm for doors fabricated from 1.25 mm thick sheet, with one or more rebate including necessary fixing lugs, hinges, lock strike plate, etc. and one shop coat of priming including plain cement concrete 1:3:6 type C-0 (using 12.5 mm graded mechanically crushed stone aggregates) in filling of door frame complete ,all as specified and as directed.

Material and labour for plain cement concrete 1:3:6 type C-1 (using 20 mm graded mechanically crushed stone aggregates) as in fixing of hold fasts, copings, bed plates,kerbs or mud stops, lintels upto 1.50m span, plinth courses , seismic and other bands and the like, finished the surface fair and even, including necessary form work complete all as specified and directed. Note- If reinforced concrete, reinforcement shall be measured and paid for separately.

Suppling and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification complete all as specified and as directed.

Suppling and fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M. S. tubes for top & bottom rails. M. S. frame shall be covered with heat moulded plain colour PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame as per specification complete all as specified and as directed. Note- Contractor shall submit to Engineer-in-Charge the Purchase vouchers before claiming payment.

Supply and fixing factory made flush shutters 35 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides, ISI marked, complete all as specified and as directed. Note- Contractor shall submit to Engineer-in-Charge the Purchase vouchers before claiming payment.

Supply and fixing factory made flush shutters 30 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides, ISI marked complete all as specified and as directed. Note- Contractor shall submit to Engineer-in-Charge the Purchase vouchers before claiming payment.

Supply and fixing IInd class (hollock) factory made 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed.

Supply and Fixing in repair magnet catcher 75 mm brass body fixed in cabnet shutter (one portion) and wooden frame (other portion) with screw complete all as specified and as directed .

Supply and fixing stainless steel hinges, medium weight cold rolled mild steel, size 100mm, ISI marked, complete all as specified and directed .

Supply and fixing 250 mm aluminum anodised sliding door bolt, ISI marked, with hasp, staple (bolt type) complete with clamps bolt not less than 16mm dia and fixing clips of sheet, cast or extruded section and fixing bolts an sliding bolt of extruded section or cast aluminum alloy, complete all as specified and directed .

Supply and fixing in repair, 250 mm aluminum anodised sliding door bolt, ISI marked, with hasp, staple (bolt type) complete with clamps bolt not less than 16mm dia and fixing clips of sheet, cast or extruded section and fixing bolts an sliding bolt of extruded section or cast aluminum alloy, complete all as specified and directed.

Supply and fixing, aluminium anodised barrel tower bolts of extruded section, 150mm, ISI marked, complete all as specified and directed .

Supply and fixing in repair, aluminium anodised barrel tower bolts of extruded section, 150mm, ISI marked, complete all as specified and directed .

Supply and fixing, extruded aluminium alloy handles with plates, fabricated type, anodised 125mm size, ISI marked, complete all as specified and directed .

Supply and fixing in repair, extruded aluminium alloy handles with plates, fabricated type, anodised 125mm size, ISI marked, complete all as specified and directed .

Supply and fixing Hasp and staple Size of 100mm, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws, ISI marked, complete all as specified and directed.

Supply and fixing in repair, hasp and staple Size of 100mm, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws, ISI marked, complete all as specified and directed.

Supply and fixing 300 mm size mild steel door spring including roller and roller plate by means of welding complete all as directed.

Supply and fixing Door seal strip with plastic beading, fixed in repairs, complete all as specified and directed .

Supply and fixing Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, overall length of cover plate 140 mm, ISI marked complete all as specified and as directed.

Supply and fixing in repair, double leaged floor door stopper of over all length of cover plate 140 mm of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor complete all as specified and directed .

Supply and fixing in repair, mild steel, wire, type I, Gate and shutter, hooks and eyes 75mm complete all as specified and directed .

Supply and Fixing 40mm dia, cupboard knobs fixed with nut, screw and washer of brass polished, bright finished complete all as specified and directed .

Supply and fixing double shutter steel window box type ERW hollow P section comprising of glazed/gauged skeleton shutter fabricated from following sections :- (a) ERW hollow P section frame of size 60 mm x25 mm made from 1.25 mm thick MS sheet (02 Nos i.e. 01 for glazed shutter and 01 for gauzed shutter ). Both P section shall be welded with flat iron 25x03 mm thick all around of frame on both inner and outer faces . (b) Style and rails of window shutters shall be fabricated with ERW hollow P section of size 50 mm x25 mm made from 1.00 mm thick MS sheet and comprising of 02 Nos sash bars for glazed window leaf of T – section 20 x 03 mm thick and one No sash bar of 20 mm x 3 mm thick section for gauzed winodw leaf . (c) Vertical mullion shall be ERW hollow T -section of size 60 x 25 mm made from 1.25 mm thick MS sheet (d) The above steel window shall be deemed to include the following accessories/ fittings : i) Hold fast 150mm long mild steel flat iron 12x3 mm thick made to shape- 04 Nos per window ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt stove enamelled 150mm long- 2 Nos per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 No per leaf. (v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 No per leaf .

item No. 52.00 (contd....) vi) Pintal hinges 12 x 75 mm - 2 Nos each leaf vii) 10mm square Guard bar @ 10 cm c/c welded to frame . (viii) Fabrication and fixing arrangements as per specification including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and as directed by the Engineer-in-Charge. Notes :- (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery, grill and other accessories as mentioned above. (iii) The window upto 1.00 metre width shall consists of two leaves both for gauzed shutter and glazed shutter and all the shutters are openable. The window more than 1.00 metre width shall have two openable leaves on both outer side for gauzed shutter and glazed shutter and middle leaf/shutter shall be fixed type. (iv) Contractor shall submit to Engineer-in-Charge the Purchase vouchers before claiming payment.

Supply and Fixing Factory made box type steel section ventilator with top/centre hung shutter double leaf shutter for both glass and wire mesh type with glazing bars (measured each separately) and 04 nos pintle hinges & 04 Nos 150mm mild steel tower bolt, 02 nos steel peg stay, 02 nos steel handle to each shutter dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified. Note- Contractor shall submit to Engineer-in-Charge the Purchase vouchers before claiming payment. Guard bars and shutter glass & wire mesh measured separately.

Supply and fixing framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; angle iron chowkats for door ,barred iron doors; ladders framed balusters; walk ways; railings; and similar work conforming to Fe-290-Gde E-165 complete all as specified.

Supply and fixing stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

Supply and fixing figured glass 3mm thick pin head type, in square not exceeding 0.5 Square metre each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified and as directed.

Supply and fixing for sheet glass 4mm thick, ordinary quality and glazing with oil putty, in square not exceeding 0.5 Square metre in each pane or with wooden beads to wooden shutters, complete all as specified and as directed.

Material and labour for prepration of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and as directed.

Material and labour for prepration of new painted wooden or wood based surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint,over one coat of pink primer complete all as specified and directed.

Material and labour for preparation of old steel surface, of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Material and labour for preparation of old wooden surface, of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Supply and Fixing Stainless steel 20 mm dia curtain rod, bright finish, including set of fixing brackets (wall & end), fixed to wall with finals/finnels, connected accessaries, rubber packing, required screws and rawal plugs, fixed in repair, complete all as specified and directed.

Dismantling of brick work or stone masonary, precast cement concrete walling built in cement mortar including all quoins, arches, pillars etc., complete all as specified and directed.

Material and labour for brick work with sub class ‘B’ bricks burnt, straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:6), complete all as specified and directed.

Material and Labour for Brick work with sub class ‘B’ bricks (Except Bricks), straight or curved on plan exceeding 6 metre mean radius, built in cement mortar (1:6) , complete all as specified. ( Note- The serviceable bricks obtained from Serial item No- 64.00 will be used after removing motar, cleaning the bricks with water, etc.)

Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including racking out joints, hacking for key scrubbing down with water, etc. including removal the rubbish/ demolished material outside defence land, complete all as specified and directed.

Material and labour for rendering 15 mm thick on surface of any description of brick work or concrete wall surfaces in cement mortar 1:4 mixed with water proofing compound @ 2% by weight of cement or as per manufacturer's instruction and finished fair and even without using extra cement complete all as specified and as directed. ( Note- Supply only integral WPC shall be measured and paid separately)

Supply only integral water proofing compound, complete all as specified and as directed .

Material and labour for preparation of new plastered surfaces or previously untreated surface of wall and applying two coats of exterior emulsion paint with hand roller, over a coat of primer on plastered surface complete all as specified and directed

Material and labour for preparation of new plastered surfaces and applying two coats of cement base paint complete all as specified and as directed.

Material and labour for rendering 05 mm thick on fair faces of brick work or concrete ceiling surfaces, chajjas, etc. in cement mortar 1:3 and finished even and smooth without using extra cement including taking down old plaster of any description etc. including racking out joints, hacking for key scrubbing down with water, etc. complete all as specified and as directed.

Material and labour for preparation of new plastered/unplastered surfaces and applying two coats of white lime wash on surfaces of ceiling, chajjas, roof projection complete all as specified and as directed.

Material and labour for 10mm thick rendering in cement mortar (1:6) on surface of any description of brick or concrete and finished the surface even and fair without using extra cement complete all as specified and as directed.

Material and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper with hand roller over over 1mm thick wall care putty white cement based in two or more coats to achive smooth surface over prepared surface complete all as specified and as directed.

Material and labour for complete removal of existing treatment on surfaces of walls by using appropriate technique as approved by Engr-in-charge for complete removal of all layers of old treatment and reaching upto old plastered surface including filling up all cracks with Shalimar tar plastic (STP) crack filler and also, make good to plastered surface for the area n. exc. 0.01Square metre , if any and applying two coats of oil bound distemper with painting roller over 1mm thick wall care putty white cement based in two or more coats to achive smooth surface over prepared surface complete all as specified and as directed.

Material and labour for complete removal of existing treatment on surfaces of walls incl cornices, chajjas, sun shades etc. by using appropriate technique as approved by Engr-in-charge for complete removal of all layers of old treatment and reaching upto old plastered surface including filling up all cracks with Shalimar tar plastic (STP) crack filler and also, make good to plastered surface for the area n. exc. 0.01Square metre , if any and of walls and applying two coat of cement base paint complete all as specified and as directed.

Material and labour for preparation of old treated surfaces (Plastered or un-plastered) of ceiling by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying two coat of white wash, complete all as specified and as directed.

Supply and fixing of 15mm dia tubes, medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, fixed to walls and ceiling or laid in floors, including cutting existing steel tubing and screwing, if required for alterations and additions, complete all as specified and directed.

Supply and fixing of 20mm dia tubes, medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, fixed to walls and ceiling or laid in floors, including cutting existing steel tubing and screwing, if required for alterations and additions, complete all as specified and directed.

Refixing steel water tubing of 15 mm bore in new or old position with all new fittings as required, laids in floor , wall and on ceiling, complete all as specified and directed.

Refixing steel water tubing of 20 mm bore in new or old position with all new fittings as required, laids in floor , wall and on ceiling, complete all as specified and directed.

Supply and fixing in repair, cast iron soil, waste and vent spun pipes 100 mm bore, ISI marked, in any length, with or without ears, with cement joints, fixed to wall and laid in trenches or in floors complete, all as specified.

Supply and fixing in repair, cast iron soil, waste and vent spun pipes 75 mm bore, ISI marked, in any length, with or without ears, with cement joints, fixed to wall and laid in trenches or in floors complete, all as specified and directed.

Supply and fixing in repair stack clamps 50mmx5mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing end of stays to wall or roof for 75mm pipe, complete all as specified and as directed.

Supply and fixing in repair 100mm dia ‘P’ or ‘S’ CI trap complete all as specified and as directed.

Supply and fixing of cast iron Bend 100 mm dia with duck's foot or heel rest complete, all as specified and directed.

Supply and fixing of cast iron 'T' junction 100 mm dia with or without oval acess door complete, all as specified and directed.

Supply and fixing of cast iron sockets (double) collars, 100mm dia complete, all as specified and directed.

Supply and fixing of cast iron Branch pieces 100mm, single (equal or unequal),ordinary or inverted (spigot or socket type) or with parallel branches complete, all as specified and directed.

Supply and fixing of cast iron bends (any radius) 75mm dia diminishing pieces or tapers complete, all as specified and directed.

Supply and fixing of cast iron bends (any radius) 75 mm dia ,diminishing pieces or tapers fitted with oval access door, complete, all as specified and directed.

Supply and fixing of cast iron sockets (double) collars, 75mm dia complete, all as specified and directed.

Supply and fixing of cast iron branch pieces, 75 mm dia, single (equal or unequal), ordinary or inverted or with parallel branches complete, all as specified and directed.

Supply and fixing of cast iron 'T' junction 75 mm dia with or without oval acess door complete, all as specified and directed.

Supply and fixing of Cast Iron cowl 75/100 mm dia complete, all as specified and directed.

Supply and fixing in repair, Cast iron floor trap 75mm dia of outlet with grating, including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete and making good the disturbed surface to match the existing surface and after taking out the existing floor trap, complete all as specified and directed.

Supply and fixing in repair, bib tap, long body, screwed down, high pressure, cast copper alloy, fancy type, chromium plated, ISI marked, with capstan heads, screwed down suitable for 15mm bore pipe or union complete all as specified and directed. Make- PRIMA Cat No PLF-6202 or equivalent model in makes mentioned in Appendix 'B' of tender document. Note- Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment.

Supply and fixing in repair, angle cock, 15mm dia, cast copper alloy, chromium plated, ISI marked, screwed down, high pressure with capstain head, screwed both ends for iron pipes or for unions complete all as specified and as directed. Make-Prima Art No- PLF-6205 or equivalent model in makes mentioned in Appendix 'B' of tender document . Note: Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment.

Supply and fixing in repair, stop valves, 15 mm dia pipe, chromium plated, fancy type, ISI marked, screwed down, high pressure with capstain head, (concealed type) with sliding flange, screwed both ends for 15mm bore pipes or for unions complete all as specified and directed. Make- PRIMA Cat No PLF-6210 or equivalent model in makes mentioned in Appendix 'B' of tender document. Note- Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment.

Supply and fixing in repair brass chromium plated shower rose 150mm size with or without swivel joint with arm of standard size fixed to existing steel pipe or union 15mm bore complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixed as in repair, for cast copper alloy, chromium plated mixer for mixing hot and cold water,capstan heads, screwed down high pressure with long screwed shank and fly nuts, fancy type screwed for iron pipes and fixed bore of pipe 15mm ,complete all as specified. Make- PRIMA Cat No PLF-6213 or equivalent model in makes mentioned in Appendix 'B' of tender document. Note- Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment.

Supply and fixing in repair, Gun metal, globe or gates valves, with iron wheel head, screwed down, high pressure, heavy duty, ISI marked, screwed both ends for iron pipe or for union of 20 mm bore complete all as specied and directed. Make- Cat No PGT-1402 of PRIMA or equivalent model in makes mentioned in Appendix 'B' of tender document.

Supply and fixing in repair, Gun metal, globe or gates valves, with iron wheel head, screwed down, high pressure, heavy duty, ISI marked, screwed both ends for iron pipe or for union of 15 mm bore complete all as specied and directed. Make- Cat No PGT-1401 of PRIMA or equivalent model in makes mentioned in Appendix 'B' of tender document.

Supply and fixing in repair, vitreous china, wash hand basin, white, flat back, of size 550x440mm including painted CI brackets, embedded in wall in CM 1:4, with and including suitable size PVC waste pipe, PVC connections and chromium plated waste coupling, etc., complete all as specified and as directed.

Supply and fixing in repair, vitreous china coloured squatting pan of orissa pattern, size 580mmx440mm, white (Ist quality) with ‘P’ or ’S’ trap, with front or back inlet and integral foot rests of any pattern (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc including making good to existing floor surface and connection to flush pipe etc. complete all as specified and directed.

Supply and fixed (in repair), vitreous china wash down water closet pedestal pattern, coloured including connection to trap and to flushing pipe with ‘P’ or ‘S’ trap, plastic water closet seat cover with mild steel chromium plated hinges and chromium plated jet spray suitable for EWC with 1.5 meter flexible LDPE pipe jointed with pipe complete all as specified and directed.

Supply and fixing in repair, stainless steel sink, 1.00mm thick for kitchen, with waste coupling, 32 mm, Hard PVC flexible waste pipe, washers, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union etc., overall size 495mm x 420mm with bowl size 410mm x330mm x 160mm complete all as specified and directed.

Supply and fixing in repair stainless steel plate rack, made out of 1.00mm thick sheet of size 24"x36"x10" deep, ISI marked, fixed as in repairs complete all as specified and directed. Make- Cat No PPR-1653 of PRIMA or equivalent model in makes mentioned in Appendix 'B' of tender document.

Supply and fixing of brass chromium plated tubular towel rail (finish Glossy), 20mm dia, D type, 60cm long between flanges complete all as specified and directed. Make- PRIMA Cat No PDX -4501 A or ESSCO Cat No-1111 or Prayag Cat No. BA-20 or equivalent model in makes mentioned in Appendix 'B' of tender document. Note- Contractor shall submit a guarentee certificate for tubular towel rail from manufacturer to Engineer-in-Charge before claiming payment.

Supply and fixing in repair of virgin polypropylene cistern, 10 litre capacity, ISI marked, coloured, low level complete with PVC bend/flush pipe and making all connections including taking down existing high or low level unserviceable flushing cistern and making good the disturbed surface to match with the existing surface complete all as specified and directed. Make- Cat No PCD-1611 of PRIMA or equivalent model in makes mentioned in Appendix 'B' of tender document.

Supply and fixing in repair, PVC connections 450mm long with PTMT nuts and PVC washers on both ends fixed to 15 mm bore of pipe complete all as specified and directed.

Supply and fixing in repair, CP grating doom (openable type) 100mm dia with or without waste hole both.(minimum weight 25 gms) complete all as specified and directed.

Supply and fixing in repair, sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

Supply and fixing in repair, soap dish size 160x160x90mm, vitreous china white, fixed to plugs with chromium plated brass screws complete all as specified and directed.

Supply and fixing, water storage tank 1000 ltr capacity HDPE Triple layer, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut , ISI marked, screwed and suitable for iron pipe 20 mm bore,including taking down the unserviceable water tank and removing from site, complete all as specified.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards/slabs/blankets, any thickness including cover fillets and false ceiling frame work of any size/ description complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of GI Metal Suspended ceiling of approved materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm centre to centre and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm centre to centre along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, and as directed by Engineer-in-charge. GI Metal Ceiling laying perforated Tengular edge global white colour tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fibre acoustical fleece. Note- Ceiling tiles and ceiling grid shall be of the same make. Contractor shall submit to Engineer-in-Charge the Purchase vouchers and MTC before claiming payment.

Taking down copper/ aluminium point wiring(light, fan, socket or power) complete, including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions seperately) and making good distrubed surfaces of wall, floors, etc complete.

Material and labour for point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall surfaces of any description and on surface on ceiling surfaces and including provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes modular type of size/modules as required at site with earth dolly (boxes shall be galvanised or painted with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally) including provision of new covered plate over sunken box for housing the modular switches , modular socket outlets,modular fan regulators etc. and making smooth the disturbed surfaces as per existing complete all as specified and as directed. Note :- a) .All chases will be cut by chase cutter only b) Switch, socket outlet and fan regulators to be measured and paid for separately .

One light/fan/Ext Fan point controlled by one way switch

One Bell point controlled by one way switch

One light point controlled by 2 way switch

One 3 pin, 6 Amps, socket outlet controlled by one switch on independent board

One 3 pin 6 Amps socket outlet controlled by one switch on Same board

Description Same all as per srl item No 120.00 here-in-before but for one socket outlet 16 Amp with 2.50 sq mm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 2.50 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade ISI marked with multi stranded copper wire as earth continuity conductor connected to common earth dolly complete all as specified and as directed.

Description Same all as per srl item No 120.00 here-in-before but for one socket outlet 16 Amp with 4.00 sq mm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 4.00 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade ISI marked with multi stranded copper wire as earth continuity conductor connected to common earth dolly complete all as specified and as directed.

Supply and fixing modular switch 1 module, single pole, one way 6 Amps flush type, 230 volts complete all as specified and as directed.

Supply and fixing modular switch 1 module, single pole, one way 16 Amps flush type, 230 volts complete all as specified and as directed.

Supply and fixing modular switch 1 module, single pole, two way 6 Amps flush type, 230 volts complete all as specified and as directed.

Supply and fixing modular bell push 6 Amp, 1 way, 1 module, 230 volts complete all as specified and as directed

Supply and fixing modular socket outlet 2/3 pin combined, 6 Amp, one way, two module, 230 volts complete all as specified and as directed.

Supply and fixing modular socket outlet 3/3 pin combined, (6pin), 6/16 Amp, one way, two module, 230 volts complete all as specified and as directed.

Supply and fixing modular electronic fan step regulator suitable for ceiling BLDC fan, any type/make/sweep 120W, 2 module, 230 volts , 50 Hz, AC supply complete all as specified and as directed.

Supply and fixing calling door bell electronic, music type, 230 volt AC including removing unserviceable bell, complete all as specified and as directed

Supply and fixing ceiling rose surface type 2/3 terminal polycarbonate, isolated body complete all as specified and as directed .

Supply and fixing 25 Amp MCB, DBOXx SRCD with 16A plug and play all-in-one device complete all as specified and as directed Note- The MCB shall provides protection to humans from electric shock due to direct or indirect contact as well as provides protection from overload and short circuit faults. It shall be designed such that user can easily upgrade his installation by replacing existing socket boxes and get built-in protectioin.

Supply and fixing lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings, complete all as specified and as directed.

Supply and fixing decorative wall light fixture made up of Polycarbonate, suitable for 9 W retrofit LED lamp B22 base all as specified and directed.

Supply only LED lamp 10 watt threaded/pin end, warm/cool lamp type for fixing on existing batten/angular holders complete all as specified and as directed.

Supply and fixing 20 Watt wall mounted LED batten with polycarbonate housing and integrated electronic driver. and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed.

Supply and fixing in repair, 10 Watt wall mounted LED batten with polycarbonate housing and integrated electronic driver. and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed.

Supply and fixing LED surface mounted bulk head luminaries 8-10 watt with min 800 lumen, industrial model, IP 65, PVC housing, surge protection including driver and LED lamp etc complete with all accessories, connecting with copper conductor flexible cable from ceiling rose to connector of the light as in repair complete all as specified and as directed.

Supply and fixing in repair 15 watt LED Light New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08 with all accessories internally pre-wired and suitable size bracket including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed.

Supply and fix sheet metal MCB DB SPN 8 way with 200 Amps rated bus bar single pole and neutral with double door IP-54 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old unserviceable enclosure complete all as specified and as directed.

Supply and fixing MCB SP, 6-40 Amps, 240 volt,10 KA , 'C' curve as per site requirement including removing old unserviceable MCB complete all as specified and as directed.

Supply and fix MCB SPN, 32/40 Amps, 240 volt,10 KA , 'C' curve as per site requirement including removing old unserviceable MCB complete all as specified and as directed.

Supply and laying sub main wiring with two run of 4 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 4 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked multi stranded copper conductor as earth continuity conductor connected to common earth dolly and concealed on wall/ceiling surfaces in PVC conduit medium grade ISI marked of adequate size for housing the wires including making good distrubed surfaces of wall/ceiling with the existing surface complete all as specified and as directed. Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. (ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length.

Taking down exhaust fan dismantling and painting of exhaust fan complete at site by cleaning the fan motor assembly body, blade of exhaust fan, filling the cavity, rubbing with sand paper, taking off old paint with the help of chemicals & painting the Exhaust fan with one coat of superior quality synthetic enamel paint including replacement of unserviceable capacitor, bearing/bush, rubber bushes, minor nuts, bolts, screws, washers, greassing in fan bearing and refixing in the same location connecting up with twin core twisted flexible copper conductor after writing the MES number on the exhaust fans of any sweep with black colour synthetic enamel paint complete all as specified and as directed.

Material and labour for opening the stator & rotor of the 300mm sweep Exhaust fan, cutting the existing worn winding & rewinding the fan with superior quality copper wire and filling the varnish as insulation between each winds and covering each loops of winding by sleeves and paper & reassembling of complete exhaust fan complete and testing all as specified and directed.

Taking down ceiling fan and and replacement of fan controller as per existing model and make and cleaning all dust etc, replacement of unserviceable bearing/bush, nuts and bolts, etc. if required and refixing in the same location connecting up with twin core twisted flexible copper conductor complete all as specified and as directed.

Disconnecting electric/water supply connection, taking down carefully geyser of any capacity, cleaning the surface, filling the cavity, rubbing with sand paper, taking off old paint with the help of chemicals & painting the geyser with one coat of superior quality synthetic enamel paint including replacement of unserviceable replacement of indicator lamp, non return valve (Brass), element and tharmostate and refixing the same location after repair including provn of twin core cable of suitable size 3 core from geyser to powerpoint with plug top 15A complete all as specifed and directed.

Earthing complete with and including galvanised steel earth plate electrode 60 cmx 60cm x 6 mm thick surrounded by mixture of charcoal and salt in alternate layers, buried directly in ground vertically in a pit of depth not less than 2.25 meter deep below ground level with top as of the plate at a depth of not less than 1.5 mtrs below normal ground level connected to galvanized iron or steel earth lead wire 4.0 mm dia,( NO 8 SWG) by means of bolts ,nuts, check nuts and washers of galvanised iron or steel earth wire protected by galvanised steel pipe 15 mm bore (light grade) and connected to main switch or main control board all as shown in electrical plate No. 3 of SSR - 2009(Pt I) & including necessary excavation and earth work. The rate also include charcoal and salt in alternate layers, 20 mm bore GI pipe (Light grade ) for watering , protection pipe funnel, wire mesh , PCC 1:2:4 type B1 chamber in cement concrete ,50 mm thick precast RCC M-25 ( Normal mix) cover duly reinforced with XPM (weight not less than 3 kg /sqm ) and CI frame etc , and including provision of test point , connecting to test point and testing on completion etc, complete all as specified. NOTE : The unit rate include earthing lead and protection pipe upto 7.5 metre from top of earth plate.

Amount of credit of Rs. 231728.40 for retrived old material as mentioned in Schedule 'A' section-II of tender document in pdf form, will be deducted offline while acceptence of tender.

M/S PARMOD KUMAR (BID ID -3362353)

shiv const co (BID ID -3362024)