REPAIR / MAINT OF STEEL FURNITURE AT AIR FORCE STATION UDHAMPUR UNDER GE (AF) UDHAMPUR

Amount

STEEL FURNITURE : Taking down worned out components of the following steel furniture, S&F new component as per shape and size specified on respective drawings and as directed by Engineer-in-charge

ALMIRAH LARGE STEEL WITH SHELVES (FD-351/1031) complete all as specified and directed by Engr-in-Charge.

Shutter (Single Leaf) made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side after preparation surfaces

Back made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side.

Side made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side.

Bottom made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side.

Shelves made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side.

Six Levers lock Make : Godrej/Harrison/Link with duplicate keys.

Three way Locking Device of 10 mm dia MS rod as per trade pattern incl a coat of red oxide primer.

Chromium plated Steel Handle 125mm.

Chromium plated MS Key plate fixed with screw and nuts.

Leg made of 1.6 mm thick MS sheet with Gas welding incl a coat of red oxide primer.

Almirah Small/ Medium steel (FD-350 /1032/243) complete all as specified and directed by Engr-in-Charge.

Shutter (Single Leaf) made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side.

Shelves made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side.

Back made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side.

Side made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side.

Bottom made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side.

Six Levers lock Make : Godrej/Harrison/Link with duplicate keys.

Three way Locking Device of 10 mm dia MS rod as per trade pattern incl a coat of red oxide primer.

Chromium plated Steel Handle 125mm.

Chromium plated MS Key plate fixed with screw and nuts.

Leg made of 1.0 mm thick MS sheet with Gas welding incl a coat of red oxide primer.

Locker Bedside Steel ( FD-257/1029) complete all as specified and directed by Engr-in-Charge.

Shutter (Single Leaf) made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side.

Back made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side.

Side made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side.

Bottom made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side.

Shelves made of 1.0 mm thick MS sheet applied with a coat of red oxide primer on both side.

125mm Steel Handle 'D' type for Locker Bedside steel.

Leg made of 1.0 mm thick MS sheet with Gas welding incl a coat of red oxide primer.

75mm haps & stapple fixed with rivets of locker steel.

Hanging Rod of 1.6mm thick chromium plated MS Rod.

TABLE DINING OR's ( FD-165(M) ) complete all as specified and directed by Engr-in-Charge.

Top of 18/19 mm thick particle board of size 1900 mm x 685 mm covered with aluminium sheet 22 guage on top complete all as specified and fixed with frame with machine screws, as directed by Engineer-in-Charge.

Rubber shoe to legs.

CHAIR CB STEEL WITH ARMS/WITHOUT ARMS ( FD-75(M) complete all as specified and directed by Engr-in-Charge.

Seat frame of Chair CB Steel with Arms of 1st class hard wood duly polished with high class black polish incl weaving with 2 mm wide half round plastic cane with Godrej pattern & border with 3 mm wide plastic cane superior quality as shown in drawing.

All as per item No 6.01 here-in-before but back frame

All as per item No 6.01 here-in-before but Seat frame for Chair CB Steel without Arms.

All as per item No 6.01 here-in-before but back frame.

Arms rest for Chair CB Steel with Arms of 1st class hard wood duly polished with high class black polish.

PVC cap at top of the frame of the chair (02 Nos to each chair).

PVC Shoe at bottom of the frame of the Chairs (04 Nos to each chair).

TABLE OFFICE CLERK/TYPIST STEEL (FD-84(M)/1004/FD-1006) complete all as specified and directed by Engr-in-Charge.

Top made of 18/19mm thick both side prelaminated particle board with PVC edge band tape/wooden beading to edges of the top as directed by Engineer-in-charge.

Drawer made of 22 gauge MS sheet with a coat of red oxide primer.

Six levers Lock of Godrej/Harrison with duplicate keys.

PVC Shoe at bottom of the leg of the Table.

TABLE OFFICE OFFICER STEEL (FD-84(M)/1003) complete all as specified and directed by Engr-in-Charge.

Top made of 18/19mm thick both side prelaminated particle board with PVC edge band tape/wooden beading to edges of the top as directed by Engineer-in-charge.

Drawer made of 22 gauge MS sheet with a coat of red oxide primer.

Six levers Lock of Godrej/Harrison with duplicate keys.

PVC Shoe at bottom of the leg of the Table.

TABLE 3' x 2' STEEL WITH DRAWER ( FD-283/1008)/Table for Hav & OR Steel (FD-223/1007) complete all as specified and directed by Engr-in-Charge.

Top made of 18/19mm thick both side prelaminated particle board with PVC edge band tape/wooden beading to edges of the top as directed by Engineer-in-charge.

Drawer made of 22 gauge MS sheet with a coat of red oxide primer.

PVC Shoe at bottom of the leg of the Table.

TABLE 3' x 3' STEEL (FD-291/1009) complete all as specified and directed by Engr-in-Charge.

Top made of 18/19mm thick both side prelaminated particle board with PVC edge band tape/wooden beading to edges of the top as directed by Engineer-in-charge.

PVC Shoe at bottom of the leg of the Table.

CHARPOY IP WITH PLYTOP (FD/MAP-II/01) complete all as specified and directed by Engr-in-Charge.

12mm thick ply wood top BWR Grade ISI Marked of size 1950mm x 900mm (Single piece) to be fixed to frame with MS nuts & screws.

PVC Shoe at bottom of the leg of the Charpoy.

Charpoy GI Pipe with Plytop: (FD-220) complete all as specified and directed by Engr-in-Charge.

3 way Galvanized Iron Elbow 32 mm dia. Note weight of each elbow shall not be less than 450 grams.

Galvanized iron check nut 32 mm dia. Note :- weight of each check nut shall not be less than 125 grams.

Long rail of 32 mm dia galvanized iron pipe medium grade incl threading at both ends as directed.

Short rail converted out of retrieved Long rail, Item No 12.03 above incl cutting, threading as required and directed.

Leg converted out of retrieved Short rail, Item No 12.04 above incl cutting, threading as required and and directed.

Provn of Two Nos MS cleat as shown on drg to hold the MNF set and one MS plate at the bottom to each Leg converted out of retrieved Short rail.

12mm thick ply wood top BWR Grade ISI Marked of size 1980mm x 900mm (Single piece).

(Conversion of existing GI pipe charpoy with nylon newar to GI pipe charpoy with plywood top) Replacement of old existing unserviceable/ damaged cotton/ nylon newar from charpoy GI pipe with new plywood top following under mentioned steps, complete all as specified as directed by Engineer-In-Charge. (a) Taking out old existing unserviceable/ damaged cotton/ nylon newar from both top of charpoy Gl pipe and patti/steel fastners etc. (b) Fixing 02 Nos stiffeners of mild steel angle iron 25mmx25mmx3mm, 900mm long, at equal distance and perpendicular to long rails of GI charpoy, fixing by drilling holes including counter sunk screws, nuts and washers at both ends on top side of long rails. (c) Drilling holes two Nos. of 7mm dia in each long rail, short rail and newly welded stiffener of mild steel angle iron. (d) Top of charpoy with plywood, 12mm thick with seven Nos. of ply, commercial, BWR grade, type BB, size 1980mmx900mm fixed to Gl pipe frame with mild steel conter sunk screws, nuts and washers, as two Nos in each long rail, short rail and newly welded stiffeners of mild steel angle iron. (e) Painting of mild steel stiffeners with two coats of synthetic enamel paint over one coat of zinc chrome primer after preparing the surfaces. (f) Prepration of the existing old decorated surfaces of Charpoy Gl pipe newar by removing of all dents and spray painting with one coat of synthetic enamel silver paint of approved quality on external surface, complete all as specified and shown in the drawings and as directed by Engineer-in-chargre.

Teapoy Verandah complete all as specified and directed by Engr-in-Charge.

Top made of 18/19mm thick both side prelaminated particle board with PVC edge band tape/wooden beading to edges of the top as directed by Engineer-in-charge.

PVC Shoe at bottom of the leg

CHAIR WRITING MAP (FD/E6/MAP/12) complete all as specified and directed by Engr-in-Charge.

Replacement of complete seat and back with new moulded foam cushioned 40 density as shape and size, covered with tapestry cloth as approved along with PVC liping all round, as directed, Note- Cost of tapestry cloth not less than Rs 450/- RM.

Hand rest one piece made of black integral skin,reinforced with MS insert it.

CHAIR SCHOOL WITH HAND BOARD (FD/E6/MAP/05) complete all as specified and directed by Engr-in-Charge.

Hand board of 18 mm pre-laminated particle board exterior grade with 2mm PVC edging & screwed at right hand side of chair arm fixed to frame as shown on drawing.

Seat & back in one piece made of PVC and fixed with frame

PVC shoe at bottom of the leg

BED HARD STEEL( FD/E6/MAP/08(R)) complete all as specified and directed by Engr-in-Charge.

12mm thick ply wood top of size 1950mm x 900mm (Single piece) BWR Grade ISI Mark with MS screws, complete all as specified.

18mm thick prelaminated particle board at head side of the bed as specified.

18mm thick prelaminated particle board at foot side of the bed as specified.

PVC shoes at the bottom of leg.

CHAIR COMPUTER (FD/E6/MAP/01) complete all as specified and directed by Engr-in-Charge.

Replacement of complete seat and back with new moulded foam cushioned 40mm density as shape and size, covered with tapestry cloth as approved along with PVC liping all round, as directed, Note- Cost of tapestry cloth not less than Rs 450/- RM.

Hand rest one piece made of black integral skin,reinforced with MS insert it. Hand rest have slope towards front as specified.

Pedestal assembly complete.

Twin wheel coasters press fitted at the bottom of leg.

Hydraulic system.

TABLE COMPUTER (FD/E6/MAP/03) complete all as specified and directed by Engr-in-Charge.

Top of 18mm thick pre-laminated particle board incl PVC lipping all around the top.

Drawer of 18 mm thick pre-laminated particle board fixed with telescopic channel.

Keyboard tray of 18 mm thick pre-laminated particle board fixed with telescopic channel .

PVC shoes at the bottom of leg.

Chair Revolving Steel high back (TP) complete all as specified and directed by Engr-in-Charge.

Replacement of complete seat with new moulded foam cushioned 40 density as shape and size and fixed over 12mm thick hot pressed plywood, covered with synthetic leatherate as approved and as directed by Engineer-in-charge.

All as per item No 18.01 here-in-before but for back frame.

Hand rest one piece made of black integral skin,reinforced with MS insert it. Hand rest have slope towards front as specified.

Pedestal assembly complete.

Twin wheel coasters press fitted at the bottom of leg.

Hydraulic system.

Chair Verandah (FD-256, 259, 359) complete all as specified and directed by Engr-in-Charge.

Taking out old U/S cane/newar and rubber shoes from chair verandah, removing of foreign materials from the iron frame by rubbing with sand paper, painting two coats with white synthetic enamel paint and recanning seat and back with 4 mm wide half round white plastic cane of superior quality as directed by Engineer-in-Charge.

PVC/Rubber shoes as per sample approved.

Cutting down wornout portion of MS Tube of the steel frame of Tables and replace with 25mm/32mm dia 1.6mm wall thickness MS tube in one piece to bring into original size as per drawing duly welding , applying of red oxide primer after preparation of surface. Upto 300mm long piece will be counted as one.

CHAIR VERANDAH (FD/MAP-II/06) complete all as specified and directed by Engr-in-Charge. Taking down unserviceable PVC seat from chair verandah and re-fixing with best quality new PVC Seat 4 mm thick and PVC edges 20mm folded towards back and weight not less than 1.85 Kg and grooves 90x10mm 10 Nos, on seat &back including applying one coat of white synthetic enamel paint of superior quality to chairs as per drawings all as specified and as directed by Engineer-in-Charge.

All as per item No 22.00 here-in-before but for PVC Back.

Painting of the following furniture items with two coat of synthetic enamel paint (colour as approved by Engineer-in-Charge) after preparation of surfaces :-

Almirah Steel Large with Shelves, FD-351/1031.

Almirah Small/medium steel (FD-350 /1032/243).

Locker Bedside Steel ( FD-257/1029).

Table Dining OR (FD-165(M).

Chair CB steel with arms/ without arms ( FD-75(M) ).

Table office ckerk steel (FD-84(M)/1004).

Table (900x600x760)mm steel with drawer (FD-283/1008

Table 3'x3' steel (FD-291/1009).

Table officer officer steel (FD-84(M)/FD-1003).

Book Shelf open steel large (FD-69(M).

Book Shelf open steel Small (FD-69(M).

Charpoy IP with plytop (FD/MAP-II/01).

Almirah Steel Large 1/2 H 1/2 SH (MAP).

Chair writing MAP(FD/E6/MAP/12

Chair School with hard board FD/E6/MAP/05

Bed Hard FD/E6/MAP/08®

Table computer FD/E6/MAP/03

Locker steel 4 units (FD-127(M)

Rack six tier steel (FD-1038)

Teapoy Verandah (FD-255)

M/S SHARMA TRADERS (BID ID -3072152)

KHAJURIA BUILDERS (BID ID -3083628)

shivom builders (BID ID -3071765)

R K BUILDERS (BID ID -3071363)