GE(W)HSR-54 of 2019-20 REPAIR TO SUNKEN PORTION, PLUMBING AND OTHER CONNECTED ITEMS IN OFFRS MD ACCN IN ZONE A AT HISAR MIL STN UNDER GE (WEST) HISAR

Amount

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) including removing rubbish complete all as specified and directed.

M&L for 50mm thick, cement concrete 1:3:6 type C1 using 20mm graded crushed stone aggregate as in plinth protection, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and directed. .

M&L for 15 mm thick rendering in CM 1:4 on faces of sunken portion with neeru finishes mixed with WPC complete all as specified and directed. Note : WPC shall be measured and paid separately.

M&L for PCC 1:5:10 type E2 using 40mm graded stone aggregate as in mass concrete as in sunken portion incl and provding necessary slope / camber and duct for drain of water complete all as specified and directed.

M&L for applying two coats of acrylic polymer coating to vertical and horizontal plastered surfaces of sunken portion all as complete all as specified and directed .(Make : Dr FixitPidifin 2K)

Repair to flushing cistern by providing siphon washer set and providing ‘M’ seal in flush outlet pipe and making it fully functional complete all as specified and directed

S&F Brass spindle suitable for 15 mm dia CP bib tap, CP stop cock short body / long body and C P pillar cocks, fixed in repairs complete all as specified and directed .

S&F in repair vitreous China WC seat Orrisa pattern size 580 x 440mm, white with integral foot rests including cast iron ‘P’ or ‘S’ trap, lime concrete in sunken floor making connection with flush pipe using new GI flush bend (Floor portion) and making good to floors, matching to existing surfaces complete all as specified and directed.

S&F in repair Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, with 40mm dia waste coupling complete all as specified and directed.

S&F in repair PVC connection 450 mm long 15mm dia with brass nuts complete all as specified and directed.

S&F in repair PVC waste pipe 32 / 40 mm dia of standard length suitable for WHB or for sink as required at site complete all as specified and directed.

S&F in repair brass CP jet for water closet (pedestal pattern) with flexible pipe minimum 1.5 mtr length complete all as specified and directed.

S&F in repair seat cover for WC ( Anglo Indian type WC) in white colour/black colour as approved complete all as specified and directed.

Taking up or down steel water tubing and connections 15 mm bore complete all as specified and directed

Taking up or down steel water tubing and connections 20 mm bore complete all as specified and directed

Taking up or down composite water tubing and connection 16mm outer dia) complete all as specified and directed.

Taking up or down composite water tubing and connection (20mm outer dia) complete all as specified and directed

S&F 15mm bore GI tubing, medium grade with all fitting fixed to walls, ceilings or laid in floors concealed complete all as specified and directed

S&F 20mm bore GI tubing, medium grade with all fitting fixed to walls, ceilings or laid in floors concealed complete all as specified and directed

Easing of wooden doors/Steel windows/steel ventilator shutter any thickness, any size by planning with plane jack, by tightening of hinge screw, by adjusting/tightening tower bolts, sliding bolts, hammering oiling/greasing etc and making it fully functional complete all as specified and directed.

S&F in repair GI wire cloth 0.56mm nominal dia of wire and 1.18mm average with of aperture with beads etc for door shutter/ window shutter of any size/type/thickness complete all as specified and directed.

S&F in repair Glass pane ordinary quality 3mm thick not exc 0.50 sqm each pane with fixing clips, putty or wooden beads to wooden/steel frames with and including MS glazing clips not less than 6 Nos per pane and making good the surface matching existing surface complete all as specified and directed .

S&F in repair floor door stopper of aluminium alloy 150mm long anodized with hard drawn steel spring fixed length of cover plate 15 cm long complete all as specified and directed .

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F MS butt hinges medium weight 100mm long fixed to pressed steel / angle iron frames by welding and with screws to the wooden / PVC shutters / frames complete all as specified and directed.

S&F Aluminum alloy, anodised, sliding door bolt 250mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F 200mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F aluminum handle cast type anodized 150mm long fixed to PVC / panelled / skeleton / cupboard shutters all as complete all as specified and directed.

S&F in repair tubular towel rail of brass chromium plated, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.(Upto three storey height in necessary scafolding etc to execute the work.)

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc including removing rubbish complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoin, jambs, pillars etc. ncluding removing rubbish complete all as specified and directed.

M&L for Brick work with fly ash bricks straight or cured on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and directed

All as per item No 34 above but except Brick. Note : Old brick shall be used.

M&L for rendering 15mm thick in cement mortar 1: 6 on faces of brick work or concrete surfaces in patches, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 10mm thick rendering in cement 1:3 on fair faces of concrete surface of ceiling, sunshade & chajjas etc. finished even and smooth without using extra cement complete all as specified and directed.

M&L for Gl wire netting 0.90mm dia andd 12mm mesh lathing to wood or metal studding, joists, etc. in walls. Ceilings, stanchions, beams, etc. including all laps, cutting and waste complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar 1:4 as on brick or concrete walls surfaces mixed with water proofing compound as per manufacturer instructions, finished even and fair complete all as specified and directed. (Note upto three storey height including necessary scaffolding etc to execute the work)

M&L for Rough cast plaster as specified .(Rendering coat not less than 10mm thick in C:M 1:3, while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel agg size 6 to 12mm mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even) on external wall upto cill height complete all as specified and directed

Supply only water proofing compound complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coat of oil bound distemper of any tint / shade complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of cement base paint of approved shade on walls complete all as specified and directed. (Note: Upto three storey height incl necessary scaffolding etc to execute the work.)

M&L for preparation of new plastered or unplastered surfaces and applying two coats of white wash on ceiling complete all as specified and directed.

Dismantling floor, heath or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for 16 to 20mm thick Makrana White marble Slab machine cut for kitchen self flooring over cement screed base laid and jointed with grey cement slurrry mixed with pigments to match the shade of the slab including cutting rubbing and polishing over and including 20mm thick screed bed in CM 1:3 complete all as specified and directed.

M&L for Vitrified ceramic tiles 10mm thick light shade (square /rectangular ) polished , area of each tiles exceeding 0.36 Sqm nut n.exe 0.42 sqm, in floors etc set and jointed in neat cement slurry and pointed flush in white or colour cement with pigment over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for Vitrified ceramic tiles 10mm thick lght shade (sqare /rectangular ) polished , area of each tiles not exceeding 0.42 Sqm, in Vertical surfaces, dados/skirting etc set and jointed in neat cement slurry and pointed flush in white or colour cement with pigment match the surface double charged over and including 10mm thick backing coat of CM 1:3 complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for Chequered cement concrete tiles with grey cement and pigments 250mm x 250mm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in floors, 25mm thick finished fair & even complete all as specified and directed.

M&L for coloured glazed ceramic tiles of size 350x250x7/450x350x7 mm thick as in vertical surface set and jointed in neat cement slurry and pointed flush in white cement with pigment over and including 10mm thick backing coat in CM 1:3 complete all as specified and directed.

Taking down rain water pipes (any size or pattern) incl all fittings complete all as specified and directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 75mm bore complete all as specified and directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls of 110mm bore complete all as specified and directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls of 75mm bore complete all as specified and directed.

S&F PVC(SWR) bends any radius 110mm bore complete all as specified and directed.

S&F PVC(SWR) branch piece single(single Y) equal or unequal 110mm bore complete all as specified and directed.

S&F PVC (SWR) single junction (single 'T') equal or unequal provided with access door of 110 mm bore complete all as specified and directed.

S&F in repair PVC(SWR) vent cowls 110mm bore complete all as specified and directed.

M&L for 20mm thick Granite (of any tpe) work (table rubbed and polished) in steps, jambs, pillars, windowcills,cooking platforms and like in cement mortar (1:4) including pointing in white cment (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L in repair for Vitreous china wash basin, white, flat back, size 550 x 400mm, including brackets and cutting for and pinning in ends of brackets complete all as specified and directed.

S&F in repair Pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe 15mm bore all as complete all as specified and directed.

S&F in repair Ball valves, high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball , screwed for iron pipe or brass ferrule 15mm bore complete all as specified and directed.

S&F in repair Ball valves, high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball , screwed for iron pipe or brass ferrule 20mm bore complete all as specified and directed.

S&F GI wire cloth 0.56mm nominal dia of wire and 1.18mm average with of aperture with beads etc for door shutter/window shutter of any size/ type/ thickness complete all as specified and directed.

Dismantling roof tiles, single layer on roof including removing rubbish complete all as specified and directed.

Cutting or uprooting grass on old mud phuska, removing rubbish off the premises , cleaning surface and preparing to receive new mud plaster complete all as specified and directed .

M&L for 25mm thick mud phuska average consolidated thickness on flat roof excluding 3mm thick leeping plaster complete all as specified and directed.

M&L for 40mm thick brick tiles laid on mud mortar & joint grouted flush in CM (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and directed.

All as per item No 70 above but except brick tiles Note: Old brick tiles shall be reused.

M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm incl cleaning of surfaces complete all as specified and directed.

S&F in repair 15mm bore Bib taps, cast copper alloy fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions 15mm bore complete all as specified and directed.

S&F in repair Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions 20mm bore complete all as specified and directed.

S&F in repair fancy type chromium plated angle/ stop valves cast copper alloy screwed down high pressure fixed to pipe of 15mm bore complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (padestal pattern ) white / coloured including P / S trap, seat cover and all necessary work required for fixed in position complete all as specified and directed.

S&F in repair curtain rails, mild steel plastic coated, 20mm dia, fancy type with fixing brackets, stops, rollers, etc complete all as specified and directed

S&F in repair hasp and staple 100mm size, safety type, aluminium anodized including bolt to hinge plate with screws complete all as specified and directed.

S&F in repair for Prelaminated particle board, 18/19mm thick, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination in kitchen cupboards/shelves//shutters etc complete all as specified and directed.

S&F in repair continuous piano hinges 30mm flap mild steel bright finish complete all as specified and directed.

S&F in repair rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top double layered ISI marked ) of 500 litres capacity, hoisted and fixed in position including connecting up pipes i.e. nipple socket / unions etc complete all as specified and directed.

S&F in repair rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top double layered ISI marked) of 1000 litres capacity, hoisted and fixed in position including connecting up pipes, nipple socket / union complete all as specified and directed.

Taking down shutters of any description exe 1 Sqm but not exe 2 Sqm complete all as specified and directed.

S&F 35mm thick glazed and skeleton shutters open rebated and prepared to receive gauge etc (without sash bar) edges of framing plain chanfered or rounded fitted with cut and mitred breds for securing glass etc sizes of members of shutters as specified in SSR Pt-I Sec 8 Clause 8.20(a) in 2nd Class H/W complete all as specified and directed.

S&F 35mm thick plain framed panelled shutters any No. of panels with panels of plywood 9mm thick for two or more panel construction and 12 mm for single panel construction, BWR conforming to IS fixed to timber frame of 2nd class H/W , all style and rail are as per clause 8.24 (a) of SSR Pt-I all as specified and directed.

S&F in repair syphonic action PVC low level flushing cistern of 10 ltr capacity including internal fittings, brackets,32mm flush pipe etc, complete all as specified and directed.

S&F in repair 600x450x150mm fibre body cabinate looking mirror with 5.5mm thick glass complete all as specified and directed.

Removing all disintregated and loose concrete of any thickness incl plaster if any in RCC Colmn, Chajjas, slabs, beams, lintels etc, removing all loose rust/scale from exposed reinforcement bars by using wire brushes and sand paper incl cleaning of exposed surfaces of reinforcement with protective anti corrosive epoxy bonding chemical (Male: Pidilite) and tied reinforcement bars/IRC fabric 50mmx 50mm x 25 gauge if reqd to reinforment concrete bonding primer uniformly to exposed surfaces and applying cement mortar 1: 3 : 1 with MPC (1 part cement :1 3: Part Sand : 1 Part 6mm course aggregate ) to an average thickness not less than 20mm incl IRC 50mm x 50mm x 25 gauge or reinforcement bars and revoving debris outside MD land all as specified and as directed by Engr-nCharge. (NOTE : Upto the height of 3 (Three) storey buldg incl necessary scaffolding to execute the work.)

Racking out old cement mortar joints of roof incl M&L flush pointing in CM 1:3 up to depth of 20mm incl cutting vegetations, brushes from roof surfaces etc complete all as specified and directed all as specified and directed by Engr-in-Charge. (NOTE : Upto the height of 3 (Three) storey buldg incl necessary scaffolding to execute the work.)

M&L for preparation of old plastered or unplastered surfaces of walls filling depressions if any with CM 1:3 and applying one coats of white / tinted cement based paint on external surfaces complete all as specified and directed all . (NOTE : Upto the height of 3 (Three) storey buldg incl necessary scaffolding to execute the work.).

M&L for preparation of old plastered or unplastered surfaces of wall applying two coats of oil bond distemper of any tint complete all as specified and directed.

M&L for complete removal of existing treatment / paint of any description of walls (any number of layers ) by scrapping with steel scrappers or other mechanical means including applying 1.5 mm thick wall care putty to smooth finish and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

M&L for preparation of old plastered or unplastered surfaces of wall including filling of depressions if any with wall care putty and applying one coats of white wash complete all as specified and directed.

M&L for preparation of old plastered or unplastered surfaces of ceiling / soffit and applying one coats of white wash complete all as specified and directed.

M&L for preparation of old surfaces of steel of any description over 10cm width or girth and applying one coat of synthetic enamel paint including CI pipes of any dia complete all as specified and directed

M&L for preparation of old surfaces of wooden of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

S&F in repair CP Brass wall mixture for mixing hot and cold water screwed down for iron pipe and fixed in posn complete all as specified and directed .

M&L for preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

M&L for cast iron Nahani trap 75mm with grating incl jointing to waste pipe fixed in cement concrete type B-1(1:2:4) using 20mm graded stone aggregate complete all as specified and directed.

S&F in repair gun-metal, globe or gate valves with iron wheel head, screwed both end for iron pipe and fixed for 20mm bore pipe complete all as specified and directed.

M&L for plain cement concrete (1:2:4) B-1 using 20mm graded stone aggregateas in padding /roof//chajja kerb etc and like complete all as specified and directed.

S&F in repair waste coupling 32mm dia of PTMT (half or full treaded) or equivalent (Min wieght 32mm-45 gms/40mm-60gms for waste pipe complete all as specified and directed.

S&F in repair CP Bass cascade health Faucet with hose (Min length 1.5mtr of CP brass) & hook of CP brass complete all as specified and directed.

S&F in repair brass CP Basin mixture for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed

S&F in repair single flow overhead shower with shower arm of CP Brass as complete all as specified and directed.

Cleaning of PVC/ RCC O/H Water tank of capacity, exc 500 ltrs but n exc 1000 ltr capacity complete all as specified and directed by Engr -in-Charge .

Balaji Construction Co.

SITA RAM AND SONS

M/s Rao Constructions, 1173 Urban Estate-II, Hisar

m/s Rajesh Kumar

M/s Pioneer Construction Co.

RAJPAL SINGH CONSTRUCTIONS

LACHHMAN SINGH AND BROTHERS