CO EE RESIDENTIAL BUILDING OF JAL SHAKTI DIVISION TISSA IN TEHSIL CHURAH DISTT CHAMBA HP CO 1 NO TYPE V QTR

Amount

Excavation in foundation and trenches in earth work upto all depth in all kinds of soil such as pick work jumper work,blasting work,chiselling of soft /hard rock where blasting is prohibited in all leads and lifts and including trimming of sides levelling of bed to correct grade stacking the excavated soil in 15cm.layers when required into plinth sides of foundation including consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed in with all leads and lifts and soring/strutting timbering and dewatering where ever required to the entire satisfaction of the Engineer-in-charge.

Providing and laying cement concrete 1:4:8 (1 cement : 4 sand : 8 graded stone aggregate 40 mm nominal size ) and curing complete excluding cost of form work in foundation and plinth with in all leads and lifts

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering , strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs. and removal of the same for insitu- reinforcement concrete and plain concrete work with in all leads and lifts

Foundation footing bases of columns etc and mass concrete.

Columns, pillars, post and struts.

Square, rectangular or polygonal in plan.

Beam, cantilever, girders and lintels.

i) Sides and soffits of beam, beam haunching, cantilever, bressumers and lintels not exceeding 1 mtr. In depth in all heights from floor.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like.

i) Floors etc. up to 200mm in thickness.

Edges of slab and breaks in floors and walls under 20 cm wide.

Stair cases with sloping or stepped soffits excluding landings.

Vertical surface such as wall of any thickness but not less than 0.1 mtr attached pillaster buttresses etc

Providing & Laying cement concrete work 1:11/2: 3 (1 cement : 11/2 sand : 3 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work with in all leads and lifts

Foundation footing bases of columns etc and mass concrete.

Colunms pillars posts and struts upto floor two level.

Lintels, beams girders bressumers and cantilevers upto floor two level.

Stair cases (Except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto floor two level.

In walls of any thickness but not less than 0.1mtr attached pillaster etc.

Suspended floors, roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilivers up to floor two level.

Providing Tor steel reinforcement for RCC work including bending binding and placing in position complete upto floor two level with in all leads and lifts

Provdiing and laying 20 cm thick composit stone masonry with stone masonry with stone facing of chisel dressed stone one line dressed in cement mortar 1:6 (1 cement :snnd) and concrete backing with cement concrete 1:3:6 (1cement :3and :6 graded stone aggregate 20 mm norinal size) on inner face of walls including cenrting shuttering and propping complte upto floor two level with in all leads and lifts

Brick work using common burnt clay building bricks in super structure above plinth level upto floor two level in cement mortor 1:6 (1 cement : 6 sand) (Ist class brick) with in all leads and lifts

Half bricks masonry in common burnt clay building bricks in cement mortar 1:4 (1cement : 4 sand) (Ist class brick)

Providing wood work in frames of doors, windows, clearstory windows and other frames wrought, framed and fixed in position. (2nd class deodar wood)

Providing and Fixing panneled glazed or panelled and glazed shutters for doors, windows and clerestory windows,including black enamelled iron butt hinges with necessary screws. 40 mm thick. (2nd class deodar wood)

Providing and Fixing wire gauge shutters using galvenised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors, windows & clearstory windows i/c bright finished black iron enamelled hinges with necessary screws 40 mm thick (2nd class deodar wood) with in all leads and lifts

Providing & Fixing M.S. grills of required pattern in wooden frame of window etc.with M.S. flats, square or round barswith round headedbolts and nuts by screws (ornamental grills)with in all leads and lifts

6mm cement plaster to ceiling in CM 1:3 ( 1Cement :3 Sand)

15 mm cement plaster in single coat on rough side of brick/concrete stone walls for interior plastering up to floor two levels including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:6 (1 cement: 6 sand)with in all leads and lifts

Stone soling under floor.

Providing and laying cement concrete 1:6:12 (1cement:6 sand: 12 graded stone aggregate 40 mm nominal size) and curing complete excluding the cost of form work in foundation and plinth with in all leads and lifts

Cement concrete flooring 1:2:4 (1 cement : 2 sand :4 graded stone aggregate 20 mm nominal size) laid in one layer finished with a floating of neat cement.40 mm thick

Providing and laying granite stone in flooring 20mm (average) thickness base of cement mortor 1:3 (1cement : 3sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete. 20 mm thick with in all leads and lifts

PRECAST TERRAZZO TILES 20 mm THICK MARBLE CHIPS OF SPECIFIED SIZES LAID IN FLOORS,TREADS OF STEPS & LANDINGS ON A BED OF 25 mm AVERAGE THICKNESS OF CEMENT MORTOR 1: 6 (1 CEMENT : 6 SAND) JOINTED WITH NEAT CEMENT SLURRY MIXED WITH PIGMENT TO MATCH THE SHADE OF TILES ( WHEREVER REQUIRED) INCLUDING RUBBING & POLISHING COMPLETE WITH TILES OF BELOW MENTIONED SHADES :-(GREY)with in all leads and lifts

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant 600x600mmx10mm manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete with in all leads and lifts

Providing and Laying clay tiles (Khaprail) over mumty roots grouted with cement mortor 1:3 (1cement : 3 sand) over a 12 mm layer of cement mortor 1:3 ( 1 cement : 3 sand) and finished neat with in all leads and lifts.

Providing and Fixing 19mm thick water proof commercial board in shelves/box for cup board with butt joints & Fixing with nails & screws etc. complete with in all leads and lifts

Providing and Fixing 19mm thick Commercial Board water proof shutters for cup boards i/c Fixing with nickel plated piano hinges with screws etc. complete with in all leads and lifts

Providing and Fixing 1.00mm thick coloured or plain lamination sheet (sunmica) on boards/ply wood sheets with approved adhesive and nails etc complete with in all leads and lifts

Providing 40x3 mm iron hold fast 40 cm long including Fixing to frame with 10 cm dia bolts nuts and wooden pluges and embencing in C.C. block 30x10x15 cm 1:3:6 ( 1 cement:3 sand: 6 graded stone aggregate 20 mm nominal size) with in all leads and lifts

Providing and Fixing Aluminium sliding door bolts with bolts and nuts screws etc. complete with in all leads and lifts

Providing and Fixing aluminium tower bolts ( barel type) wqith screws etc. complete with in all leads and lifts

Providing and Fixing bright finished M S handles with necessary screws etc. complete with in all leads and lifts

Providing and Fixing bright finished hard drawn Hooks and Eyes 250 mm with in all leads and lifts .

Providing and fixing moulded hand rail of M.S. hollow pipe 50mm dia welded in straight lenght over M.S. flat at top of vertical balusters including one coat of red oxide priming coat complete (M.S. flat & balusters of railings shall be mesaured & paid separetely.

Providing and Fixing 12 mm thick 150 mm wide pelmet with 25 mm diametre wooden curtain roads and brackets including Fixing 25x3 mm M.S flat at 10 cm long and plugs etc. complete.!st class Deodar wood with in all leads and lifts

Steel work welded in built up sections, trusses and framed work including cutting hoisting Fixing in position and applying a priming coat of red lead paint :- In beams joists channels ,angles, tee, flats with connection plates or angle cleats as in main and cross beems, hip and jack rafters, purlins connected to common rafters and the like with in all leads and lifts

Providing & Fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coatig including Fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accessories as required as per the direction of Engineer-in-charge.

Providing and fixing ridges or hips 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge with in all leads and lifts

Providing and Fixing 15 cm wide 45 cm over all semicircular with iron plain G.I. sheet gutter with iron brackets 40x3mm size bolts and nuts and washers etc. including making necessary connection with rain water pipe complete as per design. 0.80 mm thick sheet with in all leads and lifts

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1cement:3sand:6 graded stone aggregate 20 mm nominal size with in all leads and lifts

Proving under layer for plinth protection of 75 mm thick (unconsolidated) bed dry brick/stoneAggregated 40 mm nominal size will rammed with rammed and consolidated and grouted with fine sand including preparation of ground with in all leads and lifts

Constructing course rubble hammer dessed "U" shape open surface drain with side wall 15x22 cm in cement mortor 1:6 (1cement : 6 sand) and inside plastering with cement plaster 1:3 (1cement : 3 sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1 cement :5 sand : 10 graded stone aggregate 40 mm nonminal size) and 7.5 cm cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design with in all leads and lifts

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete with in all leads and lifts

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surfacewith in all leads and lifts

Applying priming coat over new wood and wood based surfaces after and inciuding preparing the suface be thoroughly cleaning oil grease dirt and othr foreign sand papering and knotting Readymixed paint brushing wood primer pink with in all leads and lifts

Painting two coats (excluding priming coat) on new wood and wood based surfaces with enamel paint to give an even shade including cleaningthe surface of dirt, dust and other foreign matters sand papering and stopping with enamel paint other than white with in all leads and lifts

Painting two coats (excluding priming coat) over new steel and other metal surfaces,with enamel paint to give an even shade including cleaningthe surface of dirt ,dust and other foreign matters sand papering and stopping with enamel paint other than white with in all leads and lifts

Providing and laying heavy duty precast cement concrete inter locking paver blocks vibro compacted upto M-50 grade i/c border or kurb block grey or coloured over sub-base of concrete with 25 mm thick average thickness of cement mortor 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing and polishing complete (Sub base concrete floor to be paid for 60 mm thick inter locking blocks) with in all leads and lifts

WATER SUPPLY AND SANITARY FITTINGS :-Providing and fixing sand cast/cast iron spun spigot and socket soil, waste and ventilating pipes (lead caulked joints to be measured and paid for separately) with in all leads and lifts

75 mm dia

100 mm dia

Providing and fixing sand cast iron/cast iron spun fittings and accessories, Bends of required degree (any radius) with oval access door insertion rubber washer 2mm thick, bolts and nut complete with in all leads and lifts

75 mm dia

110 mm dia

Providing and fixing sand cast iron/cast iron spun fittings and accessories, Collar with in all leads and lifts

75 mm dia

100 mm dia

Providing and fixing cast iron floor trap of self cleaning design with sand cast iron screwed down or hinged grating with or without vest arm complete including cost of cutting and making good the walls and the floors with in all leads and lifts

75mm dia

100mm dia

Providing and fixing vitreous China wash down, water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(1cement : 1 sand) (Seat and over to be measured and paid for separately) Angle Indian (Universal closet)with in all leads and lifts

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers : SOLID TYPE: white plastic seat and cover with in all leads and lifts

Providing and fixing to wall ceiling and floor vitreous China low level flushing cistern with a pair of C.I. or mild steel brackets, complete with fitting such as lead valve less syphon, 15mm nominal size brass ball valve with polythene float, C.P. Brass handle, unions and couplings for connections with inlet, outlet and overflow pipes, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) with in all leads and lifts

Providing and fixing vitreous china wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings. Flat back 630x450 with in all leads and lifts

Providing and Fixing 600 mm x 450 mm bevelled edge mirror of superior glass marked on 6mm thick AC sheet or plywood sheet and fixed to wooden plug with CP brass screws and washer with in all leads and lifts

Providing and Fixing CP Brass towel rail complete with CP Brass brackets fixed to wooden plug with CP Brass screws 600 mm x 20 mm with in all leads and lifts

Providing and Fixing 600 mm x 120 mm glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws with in all leads and lifts

Providing and Fixing Toilet paper holder C.P. brass.

Providing and Fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. brass screws with in all leads and lifts

Providing and fixing Chromium plated brass bib taps with cap stain heads.i) 15 mm dia. Weight 400 gms with in all leads and lifts

Providing and fixing C.P. brass angle valve 15mm without Nuts and pipe with in all leads and lifts

Providing and Fixing 100 mm dia chromium plated grating of superior quality for floor, gully or Nahni trap with in all leads and lifts

Providing and fixing C.P. Brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws :- 750mm x 20mmm

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting. 600x 450 mm with bowl depth 150 mm with in all leads and lifts

Providing and fixing Gun metal full way wheel valve with in all leads and lifts

15 mm nominal bore

Providing and supplying MS Sheet storage tank welded arround complete with 40 mm nominal bore galvanised mild steel over flow tubes with fitting and mosquito proof coupling of approved municipal design 15 mm nominal bore ball valve and mosquite proof galvanised mild steel cover with locking arrangement including providing pads of size as required for inlet and out let tubes and inside painting with a priming coat of red lead and three coats of bitumenous paint including housing up to a height of 10 mtrs above ground level as per direction of Engineer-in-charge 2000 lit net capacity storage tank of 2.00 mm thick M.S. Sheet with in all leads and lifts

Recessed wiring for light / power plug with 2 x 2.5 sq.mm FR PVC insulated single core multistrand copper conductor of ISI marked with 20 mm dia non-metalic PVC flexible conduit alongwith 1 x 1.5 sq.mm FR PVC insulated single core multistrand copper conductor for loop earthing as required. ( Make of wire Finolex / L&T / Anchor / Havels / V Guard

Recessed wiring to light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor of ISI marked with 20 mm dia non-metalic PVC flexible conduit with 5 Amp, 250 V piano type switch ISI marked and ceiling rose ISI marked mounted on MS box having front Bakelite cover of suitable size , MS box with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor as earth wire including all accesories and connection as per direction of Engineer in Charge. ( Make of wire Finolex / L&T / Anchor / Havels / V Guard )

S.P.15 / 16 amps, one way modular switch, ISI marked

Supply and fixing of single pole MCB with sheet steel enclosure, distribution board, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, phosphate and powder painted including earthing etc. as required ( But with out MCB/ RCCB/ ISOLATOR)

Providing Installation, Testing and Commissioning of resistance type ceiling fan regulator, in existing switch box including connection with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor,earthing the regulator as required

Providing Installation, Testing and Commissioning of ceiling fan, in existingconnection with 1.5 sq.mm FR PVC insulated single core multistrand copper as required

Providing and fixing of lightning conductor finial made of 20 mm dia LED Tube 20 Walt base plate including holes etc.complete as required.

Providing and fixing of lightning conductor finial made of 20 mm dia LED Bulb 20 Walt base plate including holes etc.complete as required.

Supplying and fixing batten holder / BK angle holder ISI marked including connection etc. as required.

S.P.15 / 16 amps, one way modular switch with socket, ISI marked

Providing and installation of gyser 15 ltr capacity , ISI marked

Providing & Installation of Earthing with copper earth plate 600 mm x 600mm x 3.15 mm thick ISI marked including accessories and providing masonary with cover plate having loccking arrangement and watering pipe etc (But wih out charcoal and salt) as required.

Vinod Kumar

P C Construction

Saurabh Vasudeva

Suraj Rana