REPAIR MAINT TO LEAKAGE SEEPAGE TREATMENT INTERNAL WATER SUPPLY SYSTEM SANITARY FITTINGS ROOFING FALSE CEILING PAINTING CERTAIN BR WORKS

Amount

Material and labour Water proofing treatment of existing roofs as per details given below after complete removal of existing water proofing treatment and expose of top surface of RCC slab of any thickness, any type by stripping out old tar felt over roofs, parapets, chimney stacks etc laid horizontally or vertically including taking out layer of cement plaster etc and cleaning the surface with water and using wire brush including removing debris to outside the MOD land complete all as specified and as directed :-

(a) Dismantling existing cement concrete/ roof tiles on roof including removing debris to outside MOD land as directed.

(b) Bring upto the slope by providing PCC 1:2:4 type B1 using 20mm graded stone aggregates of average thickness of 50 mm.

(c) Rendering 10mm thick in CM 1:3 on concrete roof surfaces and finish the surface even and smooth without using extra cement including mixing liquid water proofing compound as per manufacturer’s instructions.

(d) Surface should be free from any loose paint, dust or grease. Remove all existing bitumen coatings completely by using intense wire brushing, high speed water jet & vacuum cleaner for thorough cleaning of the surface to avoid ‘Peeling off’ problems.

(e) All cracks at corner joints, channels and parapets should be properly treated. For filling cracks upto 3mm crack seal material of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical or M/s Berger paints to be used. Bigger cracks, damaged portions & hollow areas must be repaired with polymer modified cement mortar.

(f) Apply a coat of self priming smart care damp proof ultra (Code 5698) of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical or M/s Berger paints with 33% dilution with water using brush/roller on newly plastered surface after curing as per IS-456 and allow to dry for 4 to 6 hours (dilution & forced coverage requirement strictly as per manufacturer’s instructions).

(g) After the primed surface has dried, apply first coat of water proofing smart care damp proof ultra (Code 5698) of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical or M/s Berger paints using brush/roller on the same primed surface & allow to dry for 4 to 6 hours.

(h) Prepare for apply 2nd coat of water proofing smart care damp proof ultra (Code 5698) of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical or M/s Berger paints using brush/roller on the same surface. The temp to be maintained 25 to 35° C through out the all above application work.

(j) In case of severe dampness an additional coat of damp proof materials to be applied.

Note for item No 01 to 10:- (i) The work shall be carried out through authorized and qualified applicators of the following manufacturers only. MOU to be submitted before commencement of work. Make : M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical or M/s Berger paints

(ii) A performance guarantee certificate for 10 years shall be submitted by the contractor to the GE on completion of work as specified.

(iii) The unit quoted rate is deemed to include taking down of water pipeline, tanks, wires (etc) found on roof and refix at the original position after complete treatment of roof.

(iv) The unit quoted rate shall be inclusive of material, all labours, tools and plants including scaffolding required for working upto approx 7.5 mtr height from natural ground level.

(v) The unit rate quoted for item is deemed to include for Removing of accumulated earth of any width and depth upto 15 cm cleaning/cutting the grass with hand operated petrol/kerosene driven grass cutting machine and removing the grass waste around 3 m from plinth protection to outside MD land.

(vi) Adoption of necessary safety arrangement like safety belts, ropes, helmets, netting etc. which are required for safety of working labour at height exceeding 3 to 25 mtr height shall be mandatary and deemed to be included in the unit rate quoted.

M&L for cement plaster rendering 10mm thick in CM 1:6 on fair faces of brickwork or concrete surface as on wall finished even and smooth with thin layer and taking down old cement plaster on brick or stone walls, or concrete walls etc., hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises complete all as per specified and directed.

M&L for cement plaster rendering 15mm thick on fair faces of brick/concrete surfaces with two coats i.e. (10mm thick backing coat in CM 1:6 and 5mm thick finishing coat in CM 1:4) and mixed with liquid water proofing compound as per manufacturer instructions, finished even and smooth without using extra cement (WPC to be measured and paid separately) and Taking down old cement plaster on brick or stone walls, or concrete walls etc., hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises complete all as per specified and directed.

M&L for cement plaster rendering 5mm thick in CM 1:3 on fair faces of brickwork or concrete surface as on ceiling finished even and smooth with thin layer and taking down cement plaster on ceilings surface etc., hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises complete all as per specified and directed.

Supply only Liquid water proofing compound of approved make (ISI marked) all as specified and directed.

M&L preparation of newly plastered surfaces wall/ ceiling and applying three coats of white washing on ceiling/ walls surfaces complete all as specified and directed.

M&L applying two coat of cement based paint over a coat of primer, including preparation of newly plastered wall surfaces of any description, complete all as specified and as directed.

M & L for preparation of new plastered surfaces of walls applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and applying two finishing coat of oil bound distemper over a coat of primer complete all as specified and directed.

S&F PVC (SWR) pipes single socket in any length with rubber ring joints of 75 mm bore fixed to wall including taking down existing one complete all as specified and as directed.

S&F PVC bends 75mm bore including taking down existing one complete all as specified and as directed.

S&F in repairs PVC (SWR) floor trap 110mm dia of outlet pipe, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints of 110 mm bore fixed to wall/floor including taking down existing one complete all as specified and as directed.

S&F PVC bends 110mm bore including taking down existing one complete all as specified and as directed.

S&F PVC (SWR) 110mm vent cowl all as specifed including taking down existing one complete all as specified and as directed.

S&F in repairs Stack clamps made out of 50 mm x 5 mm flat iron and 110 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 110 mm bore complete all as specified and directed.

S&F in repairs Stack clamps made out of 50 mm x 5 mm flat iron and 75 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore complete all as specified and directed.

Supply and fix PVC water tank 2000 Ltrs Capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) (three layer white colour) hoisted and fixed in position all as specified in SSR Part I, including connecting the float valve of required size, PVC tank cover incl all fittings, 20mm bore GI medium grade overflow pipe and connect to inlet and including fittings outlet pipes, tank nipple, elbow, bend, union, sockets, etc complete all as specified and incl disconnecting existing tank of any description and capacity.

Supplying and laying of 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and taking out steel/plastic/cpvc water tubing and connections including cleaning for refixing 15 mm/20mm dia .

Supplying and laying of 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and taking out steel/plastic/cpvc water tubing and connections including cleaning for refixing 25mm dia .

Supplying and fixing in repairs of 20mm outer dia Female Brass Threaded Adaptor (FTA/ FBTA CPVC complete all as specified.

Supplying and fixing in repairs of 25mm outer dia Female Brass Threaded Adaptor (FTA/ FBTA CPVC complete all as specified.

Supplying and fixing in repairs 20mm outer dia CPVC brass elbow and all as specified.

Supply and fixing 15mm bore galvanized steel water tubing, medium grade with all fittings and fixed complete to walls and ceiling or laid in floors including taking up or down 15mm bore steel tubing galvanized and connection complete all as specified and directed.

Supply and fixing 20 mm bore galvanized steel water tubing, medium grade with all fittings and fixed complete to walls and ceiling or laid in floors including taking up or down 20mm bore steel tubing galvanized and connection complete all as specified and directed.

Supply and fixing 25 mm bore galvanized steel water tubing, medium grade with all fittings and fixed complete to walls and ceiling or laid in floors including taking up or down 25mm bore steel tubing galvanized and connection complete all as specified and directed.

Material and labour for Preparation of old decorated plastered or unplastered surface of wall, chajja,ceiling, balcony, facia etc., brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent, trading, oil, greasy spots and applying one coat of white wash complete all as specified and directed.

M&L for Preparation of old plastered surfaces of wall by using pressure washer, removal all dirt and dust and applying one coat of exterior emulsion weather proof paint complete all as specified and as directed. Note:-(i) Cost of scaffolding required deemed to be included in the quoted rate of item and nothing extra shall be admissible on this account.

S&F in repairs 40mm bore unplasticised PVC pipe of pressure rating 10 kgf/Sqcm fixed complete to walls, ceiling or laid in floors complete all as specified and directed.

S & F in repair PVC waste pipe 32 to 40 mm dia and length n exc 2m for WHB/Sink/Urinal up to floor trap and fixed complete all as specified

S&F Pre painted Coloured Galvalume roofing system sheet 0.50 mm thick having Zinc aluminium alloy coating double ribbed trapezoidal profile steel sheet any colour having tensile strength of 550 Mpa as in Roof covering /cladding to wall fixed with self tapping screws and including dismantling of any type of old sheets in roof coverings complete all as specified & directed.

M&L Petty repairs to leaking water in bib taps, pillar cock, stop cock, angle valve, concealed stop valve, bottle trap of any description by changing the PVC washers/ Sheet washers,head, spindle brass,jumper brass or any other minor accessories items included etc (incl taking down and refixing) complete all as specified and directed

Taking down & re fixing high or low level flushing cistern any size capacity & connections to pipes & fixing of chain & pull or lever after cleaning inside of all dirt, scale formation, including replacement of rubber washers, syphon set, float valve,handle, stopping of leakage etc complete all as specified and as directed

Petty repair to wall mixer,basin mixer,sink mixer etc including replacement of spindle brass, Jumper brass, rubber washer, head included taking down and refixing etc all as directed

S&F Vitreous china squatting pan 'Orissa' Pattern size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe ) including provision of cement concrete bedding fixed in repairs all as specified and as directed.

S & F in repairs Bib taps fancy type chromium plated with crutch or butterfly handle screwed down screwed for galvanised iron pipe or for brass ferrule and fixed complete for 15 mm bore all as specified and as directed.

S&F Wash basin vitreous china (flat back and angle back Type) size 580x400mm including taps waste chain and plug and porceline stopper but brackets including cutting for and pinning in ends of brackets or erecting stand with waste pipe ,fixed including taking taking down existing one complete as directed.

M&L for Preparation of old painted wooden surface of any description and applying one coat of synthetic enamel paint using mechanical means, not otherwise described over 10 cm width or girth, complete all as specified and directed.

S&F Rotational moulded polythene water storage tank of 1000 Ltrs capacity (three layer white colour) cylinderical vertical with closed top including 3 Nos GI check nuts and tank nipple of 25mm bore for inlet and outlet, 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball hoisted and fixed in position all as specified in SSR part -I including taking down of old unserviceable tank complete all as specified and directed.

Supply and fixing in repairs 20mm dia gun metal gate valve with iron wheel screwed both ends for iron pipe and all as specified and directed.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 meter long flexible tube and ABS wall hook including taking down existing one complete all as specified and as directed.

S&F in repairs Overhead Shower rose ø125mm complete all as specified and as directed.

S&F Angular stop cock, valves high pressure screwed both ends iron pipe or for unioins 15mm dia, including taking down existing one complete as directed.

S&F in repair Brass Chromium plated wall mixer for mixing hot & cold water screwed down for 15mm bore iron pipe complete all as specified and directed .

S & F in repair Toilet paper holder box type of vitreous china fixed to walls with chromium plated (CP) brass screws and complete all as specified.

Petty repair to internal/external water inlet water GI/CPVC pipe line of any size coming from over head tank to the quarter including socket,elbow,nipple ,with repair to water blockage , pipe line leakage, cleaning internally , removing of air/dust blockage including concealed water tubing etc n exc 3m length of any height using scaffolding and and making the water supply functinol complete all as specified and directed.

S&F in repair PVC flush ceramic colour cistern , low level, 10 litres capacity, star white with inlet float ball valve, PVC flush pipe and handle, making proper fixing and hanging arrangements (Make: /Parryware/Hindware/ Cera) all as specified and as directed.

S&F in repairs 15 mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, screwed for iron pipe complete all as directed .

Supply and fixing in repairs plastic water closet seat cover white or tinted, closed pattern with flat bottom , and cover and mild steel chromium plated or aluminised hinge device complete as directed

S&F in repairs of chromium plated tubular towel rail 20 mm dia brass D type 60 cm long between flanges complete all as specified and as directed.

S&F in repairs of Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed.(Minimum weight 15mm-90gms) and directed.

S&F in repairs Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, Urinal spreader, CP push cock, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. completed all as specified.

S&F in repairs Vitreous China urinals, half stall Urinal type (back or corner wall type), complete including providing and fixing plugs, Urinal spreader, CP push cock, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. completed all as specified.

S&F in repairs of Stop Valve standard of PTMT any colour high pressure screwed for iron pipe and fixed.(Minimum weight 15mm-90gms) and as directed.

S&F in repairs of Push tap any colour high pressure of PTMTscrewed for iron pipe and fixed, (Minimum weight 15mm-47gms) and directed.

S&F in repairs of pillar Tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. Swevel (Minimum weight15mm-110gms) and directed.

S&F in repairs of Sweivel Shower with arm of PTMT any colour and 195mm long bend of 45 degree with flange for fixed with 15mm pipe (Minimum weight15mm-90gms) and directed.

S&F 150 mm dia round/square grating of CP with or without hole including Jointed to PVC pipe complete all as specified.

S&F in repairs 32 mm Waste Coupling fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed

M&L for Preparation of old decorated plastered or unplastered surface of wall, brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent , trading, oil, greasy spots and applying one coat oil bound distemper complete all as specified and as directed.

M&L Preparation of old concrete/Asbestos/Cement/GI Sheet/Plaster surfaces over brooming down or steel wire brushing down and applying one coat of synthetic enamel paint complete all as specified and as directed.

Taking down chowkhat or frame (wooden/steel/aluminium) not exceeding 1.5 Sqm each with shutter (with out taking off shutters from the frame) all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube complete all as specified .

S&F Factory made Solid PVC Door Shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified and directed.

S&F Butt hinges 75 mm long medium weight cold rolled stainless steel complete all as specified and as directed.

Supply and fixing 150 mm long aluminium anodized barrel tower bolt extruded section complete all as specified and as directed.

Supply and fixing aluminium handles cast type anodized 150 mm long complete all as specified and as directed.

Supply and fixing in repairs 200 mm long aluminium anodized barrel tower bolt extruded section complete all as specified and as directed.

S&F in repairs floor door stopper of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor overall 140mm complete including taking down existing one all as specified and as directed.

M&L Virified Ceramic tiles 10 mm thick, light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer, 15 mm thick in Cement Mortar 1:6 complete including dismantling of existing tile and disposal of rubbish to outside MD land all as specified and as directed.

M&L Virified Ceramic tiles 10 mm thick, light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in vertcal surfaces such as skirting/ dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including screed bed or bedding layer ,15 mm thick in Cement Mortar 1:6 complete including dismantling of existing tile and disposal of rubbish to outside MD land all as specified and as directed.

M&L Repair to ends of chajjas/ parapets by removing old concrete, loose material & cleaning of the reinforcement and finishing the surface with rich cement mortar 1:3 , finished fair & even and making good (not exc 3Sqm) with existing finishes complete all as specified and as directed. Note: Rate quoted by the tenderer shall be deemed to inclusive of double steel scaffolding.

M&L Plain cement concrete (1:3:6) type C1 (20 mm graded stone aggregate), 75mm thick, as in plinth protection courses, top surface of concrete finished even and smooth with out using extra cement, including expansion joint 10mm thick filled with mastic filling comprising of 01 part of heated blown bitumen and 3 parts of sand including demolition of existing cement concrete including disposal of demolition material upto MD land complete all as specified and directed.

Material and labour for Preparation of old decorated plastered or unplastered surface of wall, brooming down or steel wire brushing down smoke soot, moulds mass, efflorescent , trading, oil, greasy spots and applying one coat of cement based paint complete all as specified and as directed.

Complete removal of existing water proofing treatment of any description and in any position including PCC padding any thickness and cleaning, wire brushing, watering & removal of debris outside MOD. NOTE :- Unit rate quoted shall also include for removal of PVC water storage tank wherever existing carefully and refixing at the same or other position after completion of roof repair work

M&L Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight).

Roughening surfaces of old concrete floors by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and directed.

M&L for Brushing neat cement slurry @ 3kg/sqm all as specified and directed.

M&L PCC 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate as in concrete padding laid to required slope incl finishing the concrete surface fair and even without using extra cement complete all as specified and as directed.

M & L for 10 mm thick screed bed or bedding layer of mortar in cement mortar (1:4) for laying roof finish as padding finished with liquid WPC as per manufacturer's instructions, complete all as specified and directed NOTE :- Integral WPC shall be measured and paid separately.

Apply oil bound bitumen primer @ 0.40 Litre / Sqm manufactured by the same agency as that of APP with density of 0.87 to 0.89 Kg / Litre at 25 degree Celsius on the prepared dry roof surface.

M&L APP polymeric membrane min weighting 3.0kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150 gms/sqm laid on primed surfaces by torch application method complete all as specified and directed.

M&L for preparation of new surfaces of any description not otherwise described over 10cm width or girth and applying two coats of solar reflective aluminium paint @ 0.10 kg/sqm of membrane surfaces complete all as specified and directed.

S&F Rotational moulded polythene water storage tank of 500 Ltrs capacity (three layer white colour) cylinderical vertical with closed top including 3 Nos GI check nuts and tank nipple of 25mm bore for inlet and outlet, 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball hoisted and fixed in position all as specified in SSR part -I including taking down of old unserviceable tank complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 600 mm including taking down existing one complete all as specified and directed.

S&F Vitreous china wash down water closet pan (pedestal pattern), white (exluding fixing bolts,flushing cistren and flushpipe) and including seat cover for pedestal pattern complete fixed in repair, all as specified and as directed.

S&F Wash hand basin table counter type 560x400x200mm vitreous china (white) with cantilever CI/Angle iron brackets embedded in concrete block, including long shank pillar tap, Brass chromium plated waste coupling 32mm bore, Waste pipe bottle trap, complete all as specified and as directed. (Make : Cera or equivalent in Parryware/Hindware)

Taking down and re-fixing the same existing Aluminium door/window/partitions (each shutter area n. exc 5sqm) after carrying out ceratin repairs as required, removing the existing beading and fixing new (i.e. including change Handles, hinges, star lock, rubber beadings, bottom bearing, clips etc) rubber beading of suitable size with adhesive, overhauling of floor springs including repairing/cleaning/greasing etc and make the same fully functional all as specified and directed.

Petty repair to wooden door,skelton door, PVC door, wooden window, wooden ventilator, cupboard door, wardrobe door with shutter (size upto 2 Sqm) including roller, windows, etc with minor repair and easying and adjustment/aligment to openable with assessories if requred any ( like roller of cupboard door, butt hinge, handle, tower bolt, beading, bow handle, etc complete) included taking down and refixing complete all as directed.

Taking down chowkhat or frame (wooden/steel) exceeding 1.50 Sqm not exceeding 4.0 Sqm each with shutter (with out taking off shutters from the frame) all as specified and as directed.

Taking down shutters of any description exc 1.0 Sq.m and n.exc 2.0 Sq.m each complete all as specified and directed.

M&L Second class hard wood plain, solid, straight Chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

Supply and Fixing 30 mm thick factory made flush shutter solid core construction with block board core and plywood face panels, comercial type on both faces complete all as specified and directed.

S&F 2nd class hard wood 35mm thick Factory made plain framed panelled shutter any number of panels of with lock rail and panel of 9mm BWP commercial ply or 12mm veneered partical board with commercial veneering on both faces. The size of rail and stile as per IS 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F Factory made 35mm thick Glazed and skeleton shutters of doors/windows, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); all as specified and directed.

Preparation of new wood or wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

Supply and fixing 100mm long Butt hinges medium weight cold rolled stainless steel, and fixed complete all as specified and as directed.

Supply and fixing 200 mm long aluminium anodized barrel tower bolt extruded section complete all as specified and as directed.

S&F aluminium handles cast type anodised 200 mm long complete all as specified and as directed.

S&F 250mm Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extrudud sections or cast- aluminium alloy and fixed complete all as specified and as directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm complete all as specified and directed.

Supply and fixing 100mm long Butt hinges medium weight cold rolled stainless steel, fixed in repair to wooden frame/welded to metal frame complete all as specified and as directed.

Supply and Fixing in repairs 250mm Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extrudud sections or cast- aluminium alloy and fixed complete all as specified and as directed.

Supply and fixing in repairs aluminium handles cast type anodised 200 mm long complete all as specified and as directed.

S&F Aluminium body door closer hydraulically regulated,designation No.3, universal type, suitable for door shutters of 851 to1000 mm in width and of weight between 61 to 80 kg and fixed including taking existing one complete as directed.

Applying silicon sealent on joints of wall,cill jambs roof etc complete all as specified as directed

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm complete including taking down existing one all as specified and directed.

M&L Hacking out old broken glass (any thickness, size, quality or description) from wooden frames/steel frames glazed with putty or fixed with beads and material and labour for 4mm thick plain sheet glass ordinary quality and glazed with oil putty or fixed with fillets 2nd class hard wood of sectional area not exc 3 Sqcm and glass not exc 0.5 sqm each pane complete all as specified and directed.

M&L Hacking out old broken glass (any thickness, size, quality or description) from wooden frames/steel frames glazed with putty or fixed with beads and material and labour for 4mm thick plain sheet glass ordinary quality and glazed with oil putty or fixed with fillets 2nd class hard wood of sectional area not exc 3 Sqcm and glass exc 0.5 sqm each pane complete all as specified and directed.

S&F in repair looking mirror 3 mm of size 600mm x 450mm on commerical ply wood 6mm thick with PVC/ wooden moulding beading fixed to wooden plugs with chromium plated brass, screws and cup, washers, aluminium frame and fixed complete all as specified and directed.

S&F PVC body cabinet box mirror of size 350mm X 450mm X 100mm PTMT alloy of approved pattern and design including taking existing one complete as directed.

M&L 25mm dia mild steel powder coated drapery rod out to length required without joint in between and fixed at openings including taking down existing one complete as directed.

Supply and Fixing in repairs Mild steel powder coated fancy type brackets fixed at both the end of drapery rod of same colour and type of drapaery rod complete all as spcified and directed.

Material and labour for 25 mm thick PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in flooring, surface finished smooth without using extra cement including demolition existing cement concrete, including disposal of demolition of material upto MD land complete all as specified and directed.

Dismantling floor, floor hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premises and M& L for Joint free Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile of size n exc 0.18 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incuding screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar (1:4) complete all as secified and directed.

Dismantling floor, floor hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premises and Material and labour for Glazed ceramic coloured tiles 350x250mm/ 450 x 300 mm x 7/8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles on vertical surface such as skirting/ dado including 10mm thick 1:3 backing coat complete all as specified and directed.

Grinding of existing mozaic/kota stone/tiles in wall/flooring including mirror polishing, cleaning of tiles/granite and joints filling and apply white cement, including grouting of floor trap surroundings with white cement complete all as specified and directed.

Supply and fixing in repairs Powder coated aluminium (minimum thickness of powder coating 50 micron) frame work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws,including rubber beading complete all as per architectural drawings and as directed.

Supply and fixing in repairs powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, star lock, including rubber beading complete all as per architectural drawings and as directed.

Supply and fixing Anodized alunimun size 605 x 605 mm snap grid frame work for false ceiling as per manufacturer instructions, with Hangers 6 mm dia. G.I. (up to 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long and 6mm thick Non asbestos fibre cement building boards, fixed to sheet suitably placed in false ceiling grid made of Aluminium/G.I./ M.S.as per specification and drawing and including dismantling old unservicable wall and celing board & including frame of any type and description, complete all as specified and directed.

Supply and fixing in repairs 7 feet 4 pipes pulley operated cloths drying system consisting of aluminium pipe of outer dia 22mm, inner dia 19.80mm, made up of detrin with rope guide mounted on channel pair of length 24 feet (distance between two pipes is adjustable) locking system to hide rope knot, channel to be mounted or fixed with self taping screws provided in kit. Rope will be HDPE double core of 4mm dia fixing to ceiling as specified and directed by Engr-in-Charge and minimum weight of one pipe shall not be less than 0.20kg/, minimum weight of rope shall not be less than 7700Gms/unit . Make : Easgdry or equivalent make.

S&F Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm fixed in repairs all as specified and directed. Make : M/s Diamond / Nirali / Amco / TATA.

S&F Plate rack of size 65 cm x 96 cm made of stainless steel fixed in repairs complete all as specified.

M&L for Preparation of old painted surfaces of steel and applying one coat of synthetic enamel paint using mechanical means over 10 cm width or girth, not other wise described complete all as specified and as directed.

M&L for Preparation of old decorated surfaces of walls by using pressure washer, remove all dirt & dust ,applying one coat of wall care putty and then applying two coats of premium oil bound distemper over one coat of primer as per manufauturer instruction of required shade complete all as specified and directed. Note:-(i) Cost of scaffolding required deemed to be included in the quoted rate of item and nothing extra shall be admissible on this account.

M&L 18/19mm thick Prelaminated particle board, interior Grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work including taking down old onecomplete all as specified and as directed.

S&F Decorative laminates of 0.90 mm thick type matt finish, colour and pattern as approved including taking down existing one complete all as specified and as directed.

Taking down MS window shutters n. exc 2 Sqm through cutting of existing any type of hinges, handle and tower bolt and fixing new box type hinges, MS handle and MS tower bolt the same window by welding. The quoted rates shall be included the following aspect:- (a) Cutting of existing piano hinges, handle and tower bolt from window frame and shutter. (b) Fixing of removed shutter in the same frame on MS box type hinges 100mm, MS handle 100mm and MS tower bolt 100mm by welding. (c) Easing and adjusting the shutter before re-fixing if required. (d) Finishing the window frame and shutter with two coat of synthetic enamel paint. (e) Necessary scaffolding material to be included as the building height is more than 10mtr. Note : Box type hinges, handle and tower bolt shall be measured separately as supply only and labour element is deemed to be included in this item.

Supply only MS Box type hinges 50mm long all as directed.

Supply only MS Handle 100mm long all as directed.

Supply only MS tower bolt 75mm long all as specified.

S&F in repairs Stainless steel peg set of having 5 pegs powder coated fixed to wall surface with pvc plug and screw complete including taking down old one complete all as specified and as directed.

Providing and injecting chemical for post constructional Anti TermiteTreatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same all as specified and directed.

M&L Repair of leakage/seepage from the Nahani trap/ floor trap of kitchen/ bathroom/ washbasin of the upper Qtr, in any position at any height, complete including change of floor trap, PVC horinzontal pipe embeded in floor in bathroom or kitchen making good to the damaged portion of flooring, laying and matching of tiles in the existing flooring, complete all as specified and directed.

M&L Repair of leakage/seepage from the wall/ door bend /door tee/ 'Y' junction/ 'T' Junction of soil pipe / waste pipe/ vent pipe of kitchen/ bathroom/WC of the upper Qtr or at the ground floor Qtr including change of any damaged soil waste pipes or fittings of any shape, specification and size, making good to the damaged portion of wall with brick work in cement mortar 1:6 or cement concrete 1:2:4 and plastering to wall in CM 1:4 and finished the surfaces matching to existing wall complete to avoid the leakage/ seepage at the site of work as directed and as specified.

Note for item No 148 & 149 :- (a) Find out main cause of leakage and take necessary steps to resolve / rectify. (b) Replace existing tiles in case leakage through NT/FT. (c) The rate also include provision of new NT/FT. (d) The unit rate is also deemed to be included for reqd bonding chemicals to arrest the leakage/seepage as directed by the manufacturer's specification. Make : M/s Sika Chemical, M/s Pidilite, M/s Dr Fixit, M/s Berger paints. Note :- An amount of Rs 60285.00 on account of credit schedule for schedule 'A' part II shall be deducted from the total amount of BOQ to arrive at the contract sum.

BYRAVESHWARA CONSTUCTION (BID ID -3186432)

M/S AMRITHESH ENTERPRISES (BID ID -3185214)

VAJRA CONSTRUCTIONS (BID ID -3186181)

SHREE BANASHANKARI ASSOCIATES (BID ID -3185125)

KRD ASSOCIATE (BID ID -3186661)

M/S SRI BALAJI ENTERPRISES (BID ID -3186596)

ARUNOTHAYA TRADERS (BID ID -3186169)