RFP For Setting up of Rajiv Gandhi Center for IT Development and e- Governance (Construction, Maintenance and Operation) at Jaipur

Amount

EARTH WORK in excavation by mechanical means (Hydraulic excavator) / manual means including dewatering if any for following depths/ areas:

Excavation over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including sorting out and stacking of useful materials & disposal of excess/unserviceable excavated earth, lead upto 5KM and lift upto 1.5 m , disposed earth to be levelled and neatly dressed: All kinds of soil

Excavation for foundation up to 1.50 m to 3.00 m depth including sorting out and stacking of useful materials and disposing of the excavated stuff up to 5KM lead.In All kinds of soil

Excavation for foundation up to 3.00 m to 5.00 m depth including sorting out and stacking of useful materials and disposing of the excavated stuff up to 5KM lead. All kinds of soil

Filling available excavated earth in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift.

Borrow Earth Filling- Supplying and filling with borrow earth suitable for backfilling including watering, ramming in layers, consolidating and dressing complete as per specification, Including the cost of carrage/ transportation (Borrow pit shall be arranged by Contractor) for all leads, royality etc.

PRE-CONSTRUCTIONAL Anti termite treatment- Supplying, Diluting and injection Chloropyrifos Emulsifiable concentrate 20% with 1% concentration for PRE-CONSTRUCTIONAL Anti termite treatment as per IS 6313 part III as amended from time to time and creating a continuous chemical barrier under and around the column pits, wall trenches, basement excavation, top surface of plinth filling, junction of wall and floor along the external perimeter of building expansion joints, over the top surface of consolidated earth of which aproch is to be laid surrounding of pipes and conduits etc. complete as per specification (Plinth floor area only shall be measured for payment and including the cost of chemical emulsion)

R.C.C Work for sub structure- Providing and laying controlled reinforced cement concrete conforming to grade M35 (IS 456 – 1976) unless stated otherwise as per specifications in the following items at any depth or height, excluding the cost of steel reinforcement but including centering, shuttering, compacting with vibrators, curing and hacking the exposed surface wherever required to receive plaster or floated steel trowelled surface wherever specified. The rate shall including for supplying & mixing the concrete admixtures/superplasticizer as per design mix, providing recesses to slabs, walls and columns and sleeves and/or openings in slabs, construction joints, sunk slabs, cantilever slabs, making holes in formwork for taking out dowels etc. to the required shape, size and slope as shown in drawings.for the work of :-Footing,raft,columns,lift walls,retaining walls,pile caps,UG Underground domestic water tank, Fire tank, STP,WTP etc. as per specification & Instructions of Engineer in charge

RCC work in Super- Structure--Providing and laying controlled reinforced cement concrete conforming to grade M35 (IS 456 – 1976) unless stated otherwise as per specifications in the following items at any depth or height, excluding the cost of steel reinforcement but including centering, shuttering, compacting with vibrators, curing and hacking the exposed surface wherever required to receive plaster or floated steel trowelled surface wherever specified. The rate shall include for providing recesses to slabs, walls and columns and sleeves and/or openings in slabs, construction joints, sunk slabs, cantilever slabs, making holes in formwork for taking out dowels etc. to the required shape, size and slope as shown in drawings. CONCRETE TO HAVE MINIMUM CEMENT CONTENT OF 375 Kg./Cu.m. for columns, slabs, beams and staircase, DG structure, overhead tank etc (the rate is inclusive of work upto all floor level including scaffolding & double scafloding )

Providing and laying controlled reinforced cement concrete conforming to grade M25 (IS 456 – 1976) unless stated otherwise as per specifications in the following items at any depth or height, excluding the cost of steel reinforcement but including centering, shuttering, compacting with vibrators, curing and hacking the exposed surface wherever required to receive plaster or floated steel trowelled surface wherever specified. The rate shall include for providing recesses to slabs, walls and columns and sleeves and/or openings in slabs, construction joints, sunk slabs, cantilever slabs, making holes in formwork for taking out dowels etc. to the required shape, size and slope as shown in drawings. (the rate is inclusive of work upto all floor level including scaffolding & double scafloding )

Providing & fixing the centering, shuttering in Double height area, whereever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels.(Plan area is to be measured)

Supply & Fixing steel reinforcement for R.C.C. including transporting, decoiling, straightening, cutting, bending and placing in positing at all levels and binding with required binding wire. For lapping, reducers or couplers should be used as per structural drawings if required. The rate to include for binding wire, chairs, spacers, reducers, couplers which will not be measured separately for payment. Quantity of steel as per drawing and with authorised overlaps only shall be measured and paid for. High yield strength deformed bars conforming to IS:1786 in all R.C.C. work (F.E. 500D Grade).

Providing & laying Plain Cement Concrete (PCC) as per following details:

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work in M20 grade Nominal Mix 1: 1.5 : 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work in M15 grade Nominal Mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) & minimum cement content to be 250 kg per Cu.mt

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work in M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm/40 mm nominal size)

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work in M7.5 grade Nominal Mix 1: 4: 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 20mm/40mm nominal size)

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work in M5 grade Nominal Mix 1: 5: 10 (1 cement : 5 coarse sand : 10 graded stone aggregate 20mm/40 mm nominal size)

Supply & Fixing Structural Steel (IS 2062): Steel work welded, in built up sections framed work including cutting, hoisting, fixing with anchor bolts / fastners in position and applying priming coat of red oxide in columns, beams and joists, channels angles, tees flats with connecting plates or angle cleats. The rate shall include the cost of primer and two coats of enamel paint (of approved shade) on all structural steel work & scaffolding etc. at all height

Terrace Water Proofing Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : (i) After surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (ii) Laying second layer of Fiber glass cloth when the first layer is still green . Overlaps of joints of fiber cloth should not be less than 10 cm . (iii) Third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proffing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around (iv) Fourth and final layer of brick tiling ‘with cement mortar or any other approved protective coarse. (which will be paid for separately) For the purpose of measurement the entire treated surface will be measured

Underground structure /basement Water Proofing -- Providing patented cement based waterproofing treatment from outside to Underground structure, liftpits, trenches and other underground strutures during construction consisting of waterproof layer over cement concrete 1:3:6 bedding finished with rough Kota stone of about 20mm thick well pointed in the joints with cement and approved water proofing compound as per manufacturer, specifications and continuing the treatment after completion of floor slab and side walls on the outer face of walls and upto a height of 300mm above the adjacent ground level the total thickness of water proofing treatment shall be about 75mm for floors and about 40mm for walls. The rate shall be inclusive of all material , labour equipment required and also cement slurry grouting if required (for vertical surfaces)

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of : i) Ist course of applying cement slurry @ 4.4 Kg/sum mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. ii) IInd course of 20mm cement plaster 1:3 (1 cement: 3 coarse sand) mixed with water. proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.. iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 Kg per Sq.mt. of area. iv) IVth course of 400 micron thick PVC sheet .(Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/Sq.mt.)

Supplying, installation of BRICK WORK/BLOCK WORK of following sizes:

Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto all floor in all shapes and sizes in : Cement mortar 1 : 4 (1 cement : 4 coarse sand) (the rate is inclusive of work upto all floor level including scaffolding & double scafloding )

Half brick masonry in Superstructure , above plinth level upto all level using bricks of designation 75 Cement mortar 1 : 4 (1 cement : 4 coarse sand) and providing and placing in position 2 Nos. ,8mm Ø M.S. bar at every third course of half brick masonry .(the rate is inclusive of work upto all floor level including scaffolding & double scafloding )

Providing and laying Autoclaved Aerated Concrete (AAC) blocks masonary 150mm/230mm/300mm thick with Grade-I AAC blocks in superstructure above plinth level upto floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-charge. (The payment of RCC band and reinforcement shall be included in the item).

STONE MASONARY--Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in Cement Mortar 1:4 ( 1-Cement : 4-Sand).

SITC of DOOR & WINDOW WORKS as per followin details

SITC of powder coated Metallic Door with door frames/chaukhats (with OR without Vision Panel) With door hinges and locking arrangements and both way handle. Prepare with rigid thermo fused film metal panels. Specification: 0.6mm thick Metal panel sheets, the internal cavity filled with adequate quantity of honeycomb. The material of the partition and that of the metal door will remain the same. The material of the partition and that of the metal door will remain the same. The door thickness shall be a minimum 45mm and the frame thickness shall be a minimum of 115mm.

Providing and fixing at all levels & locations, 120 minutes fire rated steel Fire door and frame of Galvanized steel conforming to IS:277 of approved make, overall door assembly conforming to IS 3614 Part-1 & Part-2 & BS 476 Part 22 or EN 1634 as required . Fire doors should be tested at CBRI for rating of 120 minutes (supported by certificate). Frames should be provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening. Frame should be grouted with cement & sand slurry necessary for fire doors on the clear masonry opening. Door shutter shall be made with minimum 1.2 mm thick steel pressed formed to provide a 46mm thick fully flush double skin door shell with lock seam joints at stiled edges. The internal construction or in fill material of the door to meet desired fire rating with reinforcement/rails at top, bottom, middle and vertical stile. The infill material shall be resin bonded honeycomb core or approved equivalent. The door shall be factory prepared for receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers etc complete. The edges should be interlocked with a bending radius of 1.4mm. and shall have door astragals of required profile and size provided on the meeting stile for both active and inactive leaf. The shutter is to be fixed with frame with SS ball bearing butt hinges 3mm thick. Frame shall be fixed with approved dash fasteners and concrete should be poured in hollow frame section etc. Vision panel wherever applicable should be of size at least 300 x 300mm provided as per manufacturers recommendation with a beading and screws from inside with no screws and fasteners on the surface. The glass for vision panel should be 6mm clear fire rated glass of approved make & relevant rating of the door to withstand thermal shock upto 800 degree C on hose stream test. Door frames and shutters to be finished with power coating (minimum 50 micron), all complete as per the specifications and directions of Engineer-In-Charge. (Vision panel and handle rate is inclusive of the item and Hardware i.e. locks, door closer, Panic bar, etc shall be paid for separately)

Providing & fixing Fire rated door Closer of approved make certified for 2Hrs fire rating, all complete as per direction of Engineer in Charge.

Providing & fixing Fire rated Panic Exit Device (Panic Bar) of approved make certified for 2Hrs fire rating for fire door, all complete as per direction of Engineer in Charge.

Providing & fixing Fire rated Lock of approved make certified for 2Hrs fire rating, all complete as per direction of Engineer in Charge.

Providing and fixing external grade board solid core flush door shutters ISI 2202-67 marked using Phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure 'A' including aldrop, mortice lock : 35 mm thick with decorative teak veneer with veneer polish both side. The rate shall include the work of pressed steel door frame confirming to IS 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section. size as per directed by Engineer-in-charge Basic Rate of Door Venner is 1200/- per sqm

Extra for providing other type of fittings as mentioned in annexure A i.e., (A) Single Leaf Door Shutters (i) Hinges of Size 100mm 3 Nos. (ii)Sliding Bolt one No. of length of 300mm of 12mm dia upto 35mm thick shutters and 16mm dia and 300m. length for above 35mm thick shutters1 No. (iii) Handles 150mm 2 Nos. (iv) Tower Bolts 300mm 1 No. (v) Tower Bolts 150mm 1 No. (vi) Door Stopper 1 No. (vii) Back Stopper 1 No. (B) Double Leaf Door Shutters (i) Hinges of Size 100mm 6 Nos. (ii) Sliding Bolt one No. of 350mm long 16mm dia 1 No. (iii) Handles 150mm 3 Nos. (iv) Tower Bolts 300mm 2 Nos. (v) Tower Bolts 150mm 2 Nos. (vi) Door Stopper 2 Nos. (vii) Back Stopper 2 Nos. and ( as approved by EI) : Stainless Steel Fittings

Providing and fixing IS : 3564 marked Aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing steel gate, grating, and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide. The rate shall include the cost of primer and enamel paint on all structural steel work.

SITC of Toilet Cubicles as per following details: Standard Cubicle Sizes (Regular) Total Height from Ground= 2003 mm Width = 910, 990 & 1060 mm Depth = 1550 mm Bottom Gap = 150 mm Door Size = 1750x610 mm Standard Cubicle Sizes (Differently abled) Total Height from Ground= 2003 mm Width = 1360,1660 & 1825 mm Depth = 1830 mm Bottom Gap = 150 mm Door Size = 1750x910 mm All doors, mid/end pilasters and Intermediate partitions to be made from 12 mm thick compact board of the same colour. Hardware and accessories to be in Nylon + Aluminium.Adjustable legs to anchored on the floor and then mid/end pilasters to be fixed on them. The adjustable legs are to be designed to give a bottom gap of 150 mm. On upper side top rail is fixed to maintain alignment of all pilasters. Intermediate panels (partitions) to fixed to mid pilaster and rear wall through U-channels. Each door is mounted on mid/end pilaster with 3 hinges maintaining a floor clearance of 150 mm. Door is also equipped with one coat hook and one door knob. Door can be either inside or outside opening. Opening of door can be left or right. Each Mid/end pilaster coming at the free end of the door is equipped with one privacy thumb-turn and one door stopper channel along with a rubber sponge to dampen the noise.

Design, Fabricate, deliver (Prefabricated & Assembled - to job site) and install uPVC casement / slider windows from Saint-Gobain or equivalent. The outer frame and shutters should have a sill width of 70mm for two track and casement system as well as 128mm for three track sliding system. The face width of the sash should be minimum 110mm. uPVC profiles should have a minimum wall thickness of 2.3mm in the visible area. The profiles should be welded seamlessly Zip-welded without needing corner cleaning or grooved/raised finish. Both the shutter and bead profiles should have co-extruded gaskets in the glazing area. The frame and shutters should have EPDM gaskets in the sealing area. Steel reinforcement should be galvalum minimum of 1.5 mm thickness for frames and 2 mm for shutters and approved as per structural calculations. The glass panels shall be double glazed hermetically sealed panels made of 6mm thick Heat-strengthened coated glass - Envision series SKN 454 of Saint-Gobainor equivalent with coating on surface #2 with 12mm dry air gap and 6mm thick clear heat strengthened glass of Saint-Gobain or equivalent make(654 PPM) with properties as Visible Light Transmission (VLT) as 42%, Light Reflection internal as 22%, Light reflection External as 14%,Solar Factor as 0.24, and U value as 1.5 W/sqm.k and weighted average sound reduction as minimum of 30dB as per the detail drawings ,and securely bonded & Glass tolerance of ±0.2 as per EN Standard . Structural calculations to be submitted for both glass and frames. The vertical member should not deflect more than L/175 or 19mm for SGU and L/175 or 15mm for DGU, Deflection calculation should be based upon moment distribution. Steel reinforcement should have AluminoZinc coating for higher corrosion resistance. All hardware should be designed to withstand coastal conditions. 3D hinges to be used with adjustability in 3 directions. Multipoint locking to be provided with espags of SS304 grade. All shims to be capable of transferring the load evenly and made of a suitable material (Teflon, Nylon etc) capable of lasting the life span of the system. All miscellaneous items such as peripheral sealants, backer rods, fasteners etc to be included in the rate. (with mesh shutter & fixed aluminium grill)

STEEL, ALLUMINIUM AND IRON WORK-- Providing and fixing in position S.S. hand rail in main stair case, landing ,balconies etc. in 2"(50mm) dia S.S. pipe 1.5mm thk. 304 grade resting on1"( 25 mm) S.S. pipe 1.5mm thk. 304 grade size S.S.304 grade square bars 10mm, of clear height 105cms placed at 30 cm c/c including making necessary hold fast fixture (10 mm square bars 22 cm long) embeded in staircase concrete for resting the S.S 304 grade . vertical square bars with holding etc. as per approved design and as required for the work including bending hand rail pipe to proper shape in curves with specials etc. complete

PAVING AND FLOOR FINISHES as per details given below:

P & F 1st quality fully body Vitrified Porcelain Polished tiles with skirting of size 600 x 1200mm height, 10 mm thick and on floor and steps etc.in different sizes (thickness to be specified by manufactuer) with water absortion less than 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with CM 1 : 4 as per drawing, Tiles will be laid with 2 mm gap using spacers and gap will be filled with matching color epoxy latictere Size 600 x 1200 mm. Basic Rate of Tiles is 1200/- per sqm.

P & F approved make & shade Full body Vitrified Wall tile with granite pattern, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with white cement slurry @ 3.3kg per Sq.mt, including pointing in white cement mixed with pigment of matching shade complete. It Should be antiskit smooth surface polished. Size 600 x 600 mm. Basic Rate of Tiles is 750/- per sqm

Providing & laying sandwitch platform / water trough (sandwitch of 18 mm thk Granite of approved shade and sample on top and 25 mm thk kota stone in bottom with 30 mm thk screed of (1:2:4) in between)with sandwitch supports of 25 mm thk two kota on sides and screed in between and 75 mm raised platform with kota on top as per design and approved sample for all floors / all levels / all heights. The rate includes rounding, champhering and mirror polishing of edges, facias of granite, including necessary bonding adhesive like Araldite or equivalent. (Only plan area shall be measured and paid for). Rate shall be inclusive of making holes & cutouts for SS sink, Ovel wash basin, Piller tap, Bib tap-couplin etc. complete. Basic Rate of Granite is 2500/- per sqm

Providing and fixing 18 mm thick granite stone gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over base cement mortar 1:4 (1 cement : 4 coarse sand) as per drawing, joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade. Basic Rate of Granite is 2500/- per sqm

Providing edge moulding to 18 mm thick granite stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Kotah stone slab flooring with skirting of 100 mm height width factory cut, factory polished over base of cement mortar 1:6 (1 cement : 6 coarse sand) laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing complete For area of each slab from 2001 to 5000 Sq.Cm Basic rate of Kotah stone is 550/- per sqm

Providing and fixing Green / Black Granite stone slab (18 mm th) mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete and making grooves in stairs and filling it by aluminium strips and edge moulding of each steps. Basic Rate of Granite is 2500/- per sqm

Crazy ceramic tile flooring, with under layer 12 mm thick cement mortar 1:4 (1 cement: 4 coarse sand), with joints not exceeding 5 mm, including filling the gaps with ordinary cement mixture & mixing with synthetic polyester fibre, triangular in shape having specific gravity of 1.34 to 1.40, cross section size ranging from 10 to 40 micron & length upto 6 mm , mixing fibre @ 125 grams per 50 kg of cement in cement mortar, including providing and mixing water proofing material in mortar @ 1 kg per 50 kg of cement , all complete as per direction of Engineer-in-charge.

Providing, machine mixing and laying of 75mm thick vacuum dewatered (Tremix) concrete of grade M 20 of trap metal for plain cement concrete as per detail drawings including dewatering, steel form work, compaction, panels as specified and as per recommendation of manufacturer of equipment, power floating and broom finishing or finishing smooth as specified, cutting concrete for groove as expansion joint about 1/3rd depth of concrete and 6mm wide, filling grooves with approved bitumen based sealant, cleaning, curing surface etc. all complete

Providing and laying Stone finished cement concrete paver block(400mmx200mmx200mm) as per drawing

Rubble soling: Providing and laying in basement under floor rubble soling to a consolidated thickness of 200/300mm thick rubble stone and packing , using 200/250mm size stones, using murrum (gravel) hand packed with smaller stones of suitable size well rammed and consolidated including spreading in uniform layers watering ramming, consolidating all complete as per specifications-- with rubble from outside

PLASTERING AND PAINTING

Plaster on new surface on walls in cement sand mortar 1:4 including racking of joints etc. complete fine finish : 12 mm thk. Cost includes scaffolding and filling joints between concrete and masonry in cement mortar including racking the joints to form "V" groove (the rate is inclusive of work upto all floor level including scaffolding & double scafloding )

Plaster on new surface on walls in cement sand mortar 1:4 including racking of joint etc. complete fine finish : 20 mm thk Cost includes scaffolding and waterproofing compound and filling joints between concrete and masonry in cement mortar including racking the joints to form "V" groove (the rate is inclusive of work upto all floor level including scaffolding & double scafloding )

6 mm thick cement plaster to ceiling of mix 1:3 (1cement : 3-fine sand) Cost includes scaffolding(the rate is inclusive of work upto all floor level including scaffolding & double scaffloding )

Providing and fixing Chicken mesh jali (22 gauge) at the junction of 2 different surfaces of different material component at the time of plastering to prevent cracking in plaster surface as and where directed at all floors with all leads and lifts etc.complete.

SITC of Paint Painting to new walls with 2 coats or more of plastic emulsion paint of approved brand/ manufacturer and approved shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc. complete for finished item of work over one coat of primer( total 3 coats or more including primer) complete in all respects Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC Wall Putty Material for 1mm thick Putty on all exposed portions of beams, columns and walls as directed by the consultants including mixing, scraping, and levelling the surface, cleaning and complete in all respects to receive the paints & finishes. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete

Providing & applying complete cool wall coatings( Exterior paint) on wall surface with Surface preparation: cleaning & washing Applying primer to give bonding to the substrate that reduces porosity & dampness of the surface 1 coat of primer & 2 coats of thermal insulating paint.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work.

MISCELLANEOUS ITEMS

Providing and laying 750mm wide broom finished plinth protection with 230mm X 600mm (average) toe wall in brick masonry in C.M 1:6 over 75mm thick, 400mm wide PCC 1:5:10 (below masonry) broomed finished 750 mm wide and 100mm thick cement concrete 1:2:4 over 520mm wide 150mm thick PCC 1:5:10 ,with necessary grooves for expansion joints and curved vata at the junction of wall and plinth protection including excavation ,formwork,15mm thick cement plaster outside brick toe wall tec.complete as directed by Engineer -in-charge. Include rubble soling to a consolidated thickness of 200/300mm thick rubble stone and packing using murrum (gravel) hand packed with smaller stones of suitable size well rammed and consolidated including spreading in uniform layers watering ramming.

Grading roof for water proofing treatment with water proofing compound Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing holes/pockets/cutouts in slab, beams, RCC walls with or without reinforcement during concreteing by providing forms, thermocoles including welding of reinforcement, shuttering, stagging, etc. as per drawing and direction.

(a) upto and including 0.25 Sqm but more than 0.04Sqm

(b) 0.25 SM to 0.50 SM

(c) 0.50 SM to 1.00 SM

Providing and fixing Metal perforated false ceiling at all heights including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing of metal panels with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval and also including the cost of making openings for light fittings, grills, diffusers, cutouts and trap doors made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer in Charge. The Rate is inclusive of making the Trap Doors of all size as per the requirements. The item should include all necessary fittings for lighting provisions.

Providing & fixing calcium silicate ceiling tiles of size 595 x 595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanised steel sections ( galvanized @ 170 gsm/sqm.) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200mm center to center and cross “T” of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main “T” at 600mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 21x21x0.30 mm and laying false ceiling tiles of approved texture in the grid including, wherever, required, cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats fixed to ceiling with 6 mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanised level clips spaced at 1200mm center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete at all heights as per specifications drawings and as directed by Engineer-in-Charge of thickness of tiles as mentioned below. 8mm thick. The Rate is inclusive of making the Trap Doors of all size as per the requirements. The item should include all necessary fittings for lighting provisions.

Providing and fixing calcium silicate board false ceiling at all heights including providing and fixing of frame work made of special sections. 8mm thick (with trap door)

TANK WATERPROOFING TREATMENT:Providing & Applying a complete water proofing on RCC tanks. Identifying and sealing, filling of cracks if any with cement grout mixed with, ‘Hi Seal Slurry’, repairs of pot holes if any, followed with priming of SBR. Laying of fiber mess and 2 Coats of two component Panache make or equivalent product mix of ‘Hi Seal Slurry Liquid & Powder’ resulting in to an onsite water proof membrane. Protected by 1:4 cement mortar plaster coat (Grey Cement +Panache make or equivalent product Hi CE Pack.Install protective screed by adding Panache make or equivalent admix Hi CE Pack up to 15 to 20 mm thick to bear the hydro pressure.Including material, labor, plant & tools etc.Rates are excluding the civil work of Protective screed of 15 to 20 mm .

WATER REPELLENT TREATMENT ON BRICKS AND EXPOSED:Providing & Applying of complete water repellent treatment by applying two coats of silane siloxine water base water repellent by brush or spray on concrete rendered surface / Exposed brick surface / stone cladding horizontal surface after proper cleaning and washing to that provides a complete water repellency to the surface without changing any aesthetic look of surface upto 5 years.(Including material, labour, plant & tools etc.)

Supply and installing Rain Water Percolation pits - 1500 mm in diameter up to 3200 mm deep, bottom 500 mm filled with boulders 150 - 230 mm size, over which one no. UPVC 160 mm dia (4.0 kg/cm2) perforated pipe with 8 mm dia perforations protected by a cowl on upper end 2100 mm long, surrounding filled with broken bricks up to 1000 mm, pebbles 40 to 50 mm up to 400 mm, Gravel 15 to 25 mm up to 400 mm and upper most layer of 300 mm with coarse sand of 3 to 5 mm. The top 600 mm shall be left open, with RCC grated cover on top.

Supply & Installation of toughened reflective glazing Glass :- (12 mm thick toughened glass) Including full glass of minimum 12 mm thick clear toughened glass, structural support system for top and bottom including holding system from RCC slab above false ceiling, including runner hung anchor fastener to fix it. Rubber interlinear & gaskets to fix bottom into SS "U" channel in floor. silicon sealant to filled gap.

SIGNAGES ON WALL: Providing, Fabricating & Fixing wall signage's using 304 grade Stainless steel brushed steel finish plate of 1.5 mm thick fixed on a wall using s.s studs including punched (laser cut) lettering carried out on s.s plate of required size and text as directed by Engineer over the S.S plate etc.complete. Size: 18" x 6"

SIGNAGES HANGING FROM CEILING Providing, Fabricating & Fixing signage's using 304 grade Stainless steel 1.5 mm thick brushed steel finish plate (2 nos) with 8mm thk. Acrylic sheet covered with vinyl of approved colour, sandwiched between two S.S plate and fixed with s.s struds . Sandwiched plates should be fixed in 12mm X 12mm S.S 1.5mm thk.304 grade frame and punched (laser cut) lettering carried out on both the s.s plates of required size and text as directed by Engineer and hanged to ceiling with the help of S.S 8mm thick chain at both ends with making all the fixing arrangement to the ceiling and to the plate complete etc.complete. size: 18" x 6"

Aluminium Structural glazing work – Providing and fixing of specially designed high performance semi unitized system using aluminium section of Jindal /Hindalcon make for main mullion ,corner mullion , main transom and Top & Bottom transom for main frame based structural glazing .mullion & Transom- shall be out of aluminium section size of 63.5X 58X weight 1.350 kg/m. Anodizing – The surface of aluminium section shall be finished with 15 micron anodizing in required shade .Silicon D/C 995/SSG 4000 structural sealant .weather Silicon – 789 / Ultra proof Single shutter section for glass panel .The glass panels shall be double glazed hermetically sealed panels made of 6mm thick Heat-strengthened coated glass - Envision series SKN 454 of Saint-Gobain with coating on surface #2 with 12mm dry air gap and 6mm thick clear heat strengthened glass of Saint-Gobain make(654 PPM) with properties as Visible Light Transmission (VLT) as 42%, Light Reflection internal as 22%, Light reflection External as 14%,Solar Factor as 0.24, and U value as 1.5 W/sqm.k and weighted average sound reduction as minimum of 30dB as per the detail drawings ,and securely bonded & Glass tolerance of ±0.2 as per EN Standard . Structural calculations to be submitted for both glass and frames. The vertical member should not deflect more than L/175 or 19mm for SGU and L/175 or 15mm for DGU.

Fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:4 ( 1cement : 4 coarse sand) with joints finished flush. Red Sand stone size not less than 1350 Cm2 - b) 50mm Basic Rate of stone is 550/- per sqm

Exterior Façade item

Exposed face machine cut Stone work (machine cut edges) for Wall cladding/ Veneering work up to all floor with 20 to 30 mm thick Pink Sand stone (Bansi Paharpur) /White sand stone and backing filled with a grout of 12mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade , The rate of clamps is inclusive. The rate is inclusive of work up to all floor Level including scaffolding. Basic Rate of stone is 850/- per sqm

Providing and fixing Stone jali 50mm thick Red/Pink sand stone as per ornamental design to fixed with white cement/epoxy mortar including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment, matching the stone shade. Basic Rate of stone is 850/- per sqm

Providing & Fixing decorative high pressure laminated (HPL) sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick

Providing and Fixing Aluminium composite panel of approved make 3mm thick with 0.5mm thick skin & PVDF coated approved shade for wall panelling. Main framing work to be done using 50mmx25mmx1.6mm tubular section of approved make. Stainless steel screw to be used to fix the ACP panel to be fixed to the main frame with industrial adhesive tape and panel groove to be sealed with weather proof silicon sealant suitable for glass/aluminium etc. complete in all respect as approved by Engineer-in-charge.

Providing & Fixing corner guard for columns at parking area size 45mmX45mm, height 1200mm colour: Black with yellow or White Reflective Stickers Body Material: Modified Thermoplastics (Polymer Rubberized) Fixing: Fixed on the wall & corner of columns with six 2" Screws.

Basement Floor Marking Paint - Basement floor marking with adequate nos of coats to give uniform finish with thermoplastic road marking paint in white/yellow shade, including cleaning the surface of all dirt, scales, oil, grease and foreign material etc. complete.

Under Deck Insulation -Under deck insulation with 32mm nitrile rubber of 33Kg/cu.m density covered with Aluminium finishes per specefication.

Providing and fixing stainless steel tactile indicators in circular studded pattern and elongated striped pattern. Material grade should be taken as 316 with smooth finish.

Barricading site

Providing and maintaining Barricading on the site with 2.4m High x 1.05m brand new GI sheets, sheets of 0.79mm thickness (22 B.W.G..) conforming IS. 277-1969 including fastening with galvanized iron screws and J bolts as per details etc. complete. on a frame work made out of 50mm dia MS Hollow pipes, 2mm thick spaced at 0.9m c/c both ways. The MS shall give stable supports as per direction of the Engineer-in-Charge. The frame work and GI sheets to be painted initially and re-painted after six months or in the eventuality if additional coat required in between, in opinion of Project Manager.

Dismantling of Existing Building (as per attached drawing) with necessary safety and precaution including transportation & disposal of scrap/unservicable material with all leads and lifts & stacking/segregating/storage of servicable material as per instruction of Engineer-in-charge. The rate shall include cost of all labour involved and tools used in demolishing and dismantling including scaffolding. The rate also includes for temporary shoring for the safety of the portion not required to be dismantle/pulled down or of adjoining property by providing temporary enclosures or supports where considered necessary. The rate shall be for a unit of one Job. 1.1. The demolition shall consist of demolition of one or more parts of the building as specified or shown in the drawings (Contractor is advised to visit the site before quoting the rate). Demolition implies taking up or down or breaking up. This shall consist of demolishing whole or part of work including all relevant items as specified or shown in the drawings. 1.2. The demolition shall always be planned beforehand shall be done in reverse order to the one in which the structure was constructed. This scheme shall be got approved form the Engineer-in-charge before starting the work. 1.3. Necessary propping, shoring and under pinning shall be provided for the safety of the adjoining work or property, which is to be left intact, before dismantling and demolishing is taken up and the work shall be carried out in such a way that no damage is caused to the adjoining property. 1.4. Wherever required, temporary enclosures or partitions shall also be provided. Necessary precautions shall be taken to keep the dust nuisance down as and where necessary. 1.5. Dismantling shall be commenced in a systematic manner. All materials which are likely to be damaged by dropping from a height or demolishing roof, masonry etc. shall be carefully dismantled first. The dismantled articles shall be properly stacked as directed. 1.6. Any serviceable/ Movable materials like Electric fixtures, Table/ Chairs etc., obtained during dismantling or demolition shall be separated out and stacked properly as directed with all lead and lift. All unserviceable materials, rubbish etc., shall be stacked as directed' by the Engineer-in-charge. Disposal site shall be arranged by Contractor at his cost. 1.7. On completion of work, the site shall be cleared of all debris rubbish and cleaned as directed. Taken over and Handover of items detail is mentioned in RFP.

100 MM or 50 MM WIDTH EXPANSION JOINT SETUP OF 50 MM EXPANSION SHEET:Cleaning of Concrete Surface on Both side of the Expansion Joints to remove any dust , Oil , Grease including Removal of laitence and cleaning the inside of the Expansion joint 2) Providing and applying base coat of Epoxy adhesive on both side of the joints as per width by SIKA -DUR 31C EPOXY and Placing the 3) Providing and Applying Combiplex Tape 300 mm * 1MM Expansion Joint Tape Tape 300 mm width x 1 mm thickness as per Manufacturers Methods Statement ( for 50 mm Lower Joint Side ) 4) Providing and applying the Top Coat of Epoxy Adhesives SIKA -DUR 31C EPOXY on both sides of the treated Expansion Joints as per the width of the EPDM SHEET 150MM* 1MM THICK . For terrace

Description of Work / Item(s)

Amount

Supply, installation, testing and commissioning of BMS Computer System: i9 with 11 or higher generation processor or Equivalet Server PC with latest server OS config. , Intel(R) Xeon(R) Processor, min 4.0 GHz Base frequency to 5.2 GHz or higher, 16MB L3 Cache with 32 GB RAM, & 1 TB SSD, Gigabit speed Ethernet card, USB connection & internal modem, Microsoft(R) Windows(R) 11 as per latest OS Professional Enterprise , Web server software, DVD-ROM Drive (with RAM), 100/1000/10000 Mbps (Gigabit speed) NIC for Network connection and anti virus software as per Tender Specifications. Accessories included 32 Inch LED Screen, Optical Mouse & Key Pad, Laserjet A4 Black and White printer, Windows Licensed software compatible with the above BMS System configuration complete as required.

Application Software- SITC of the following window based graphical software for IBMS system with 2 Nos Client for Operator workstation. License for minimum 10000 hard/soft I/Os to be considered and shall have provision of future expansion . The following software packages shall have below minimum features and compliances. (Make:- Metasys by Johnson Control/Desigo CC by Siemens/ ALC by Carrier /EBI by Honeywell )

a) 3D & HD vector dynamic graphics with Autocad import of plan with Zoom In & Zoom Out facility b) Native 64 Bit System , BTL,UL,EN Certified System, BACnet Profile B-AWS (Advanced workstation) as per the BTL Listing c) Multi-Monitor Support-( Min 4 Nos), Multi-language support,Object tracking on multiple cameras d) Certified OPC DA Server by OPC Foundation e) HTML5 based Web-Server software shall permit use of Standard Web-Browsers such as Microsoft Edge, Google Chrome, Mozilla Firefox, etc f) The Software shall comply to international standards and strive to deliver products that meet security standards such as ISA/IEC 62443, UL2900, ISO/IEC 27001, ISO/IEC62443 and OWASP

g) Cybersecurity SL2, Seamless integration of Security certificates within customer IT infrastructure, Microsoft’s active directory-based authentication, LDAP integration, Use of network infrastructure that supports physical network or VLAN segmentation, End-to-end encryption from client to server, End-to-end encryption between servers, Certificate-based data exchange, Encrypted backups h) Audit Trail , 4-Eye Principle, Data Point Validation, Verified tempering evidence for report transmission i) The software shall integrate with BIM data seamlessly j) Ability to provide data to other systems thru OPC DA Server and / Or Rest web services interface k) Reports - Customized reports for Trends and alarm with Graphic screen shots. l) Seamless integration of Fire alarm system should be there. m) Alarm Escalation: Assisted treatment of alarms which helps in Predefined & fast intervention steps for faster response n) Energy dashboards having cockpit view of total energy utilized. Energy and Power reports.

SITC of True IP Based DDC Standalone 32 Bit Intelligent, peer to peer communication, interoperable DDC as per the specification. The compact controller shall have inbuilt 2-port Ethernet switch . The controller shall have minimum 16 inputs/outputs inbuilt. The DDC shall have 300 Mhz processor with 128 MByte SDRAM (DDR3) and 512 MByte NAND Flash. The controller shall be freely programmable and have System functions (alarming, scheduling, trending, access protection with individually definable user profiles and categories). It should have WLAN interface, Cloud connectivity for remote access and inbuilt port for POT for local interface. Note: Comissioning tool should not be dependent on any license / dongle and no extra cost should be charged.

The above shall be housed in vandal proof, lockable & secure MS Cabinets to be supplied along with all necessary switchgear protections as required. Number of controllers shall have spare capacity of 15% for future expansion.

Controller for Chiller plant and Pumps system

Controller for AHU system ( Max 1 AHU in 1 DDC)

Controller for AHU system with VFD ( Max 1 AHU in 1 DDC) Controller shall have inbuilt facility to connect soft points

Controller for CS-AHU system ( Max 2 AHU in 1 DDC)

Controller for TFA system ( Max 2 TFA in 1 DDC)

Controller for Exaust Fans ( Max 3/4 Fans in 1 DDC)

Controller for Pressurisation Fans ( Max 3/4 Fans in 1 DDC)

Controller for Fire Fighting system

Controller for HT/LT Panel system

Controller for Transformer

Controller for DG Sets

Controller for WTP system

Controller for Plumbing system

Controller for STP & ETP system

Controller for Lift

SITC of True IP Based BTL & UL Listed for third party integration. The controller shall have 2-port Ethernet switch and WLAN interface. It should have BTL label (BACnet communications passed the BTL test) and consisting of Dual microprocessor with Storage capacity of 1 GByte RAM. It should support Real Time clock with backup of upto 7 Days using super capacitor and also should have option for external battery if required. It should Support of the major communication protocols: BACnet,/IP, BACnet MS/TP, Modbus IP and Modbus RTU upto 500 points. Note: 3rd party make integartor is not acceptable.

For Chillers on Bacnet/IP (25 Points per Chiller)

For Fire Alarm System on Bacnet/IP (1 Point per Panel)

For Secondary Pumps VFD on Modbus RS485 (7 Poins per VFD)

For AHU VFDs on Modbus RS485 (7 Points per VFD)

For Multifunctional energy meters Modbus/RS485 - (10 Points per Meter)

For Integration of Thermostats on Bacnet/Modbus/RS485 (5 Points) (Total 69 Nos. Thermostats)

For UPS on Bacnet/ Modbus/RS485 (15 Points per UPS)

For Automation lights on Bacnet/ Modbus/RS485

For Access Control Bacnet/ Modbus/RS485

Field instruments

Supplying, installing, testing and commissioning of the following sensors / transducers / transmitters. The DDC shall support sensor with DC 0...20 mA or 4...20 mA, DC 0 ... 10 V, LG-Ni 1000, 2x LG-Ni1000, Pt 1000 , NTC 10k, NTC 100k, 1000 Ohm. All sensors should be UL Listed.

Immersion Temperature Sensor LG-Ni 0.15m with SS Thermowell

Outside air temperature + humidity sensors for measuring outside air temperature. It should be provided with sun sheild and rain protection.

Current Relay

Bi Level Switch

Differential Pressure Switch Water

Water Differential pressure sensor

Differential pressure switch for Filter Status

Differential pressure switch for Blower and Hepa Filter

Duct type temperature Sensor

Duct type temperature and Humidity Sensor

Absolute Pressure Sensor for water

Water Flow Switch

Flameproof Level Switch

Voltage Transducer

Differential Pressure Sensor Air

Duct type CO2 Sensor

Supply, installation, testing and commissioning of hand held portable operator terminals (POT) minimum 7 inch. TFT display with capacitive touch screen type, shall be able to view graphs , alarms , parameters etc. POT shall have integrated web server and a BACnet/ IP web interface to connect a HTML5 browser to a device on the network. POT With all required connectors etc as per technical specification etc.

Cabling and Conduiting

Supplying, laying, termination, testing and commissioning of armoured signal cables. (4 core x 1.0 Sq.mm), PVC insulated, unshielded tinned copper conductor cable.

Supplying, laying, termination, testing and commissioning of armoured Communication cables. (2 core x 1.0 Sq.mm), PVC insulated, shielded twisted copper conductor cable.

Supplying, laying, termination, testing and commissioning of 3 Core 1.5 Sqmm, unarmoured ATC conductor multistranded, FRLS cable for Powering DDC , Actuators.

Supplying, laying, termination, testing & commissioning of CAT 6 unarmoured Cables with required accessories like RJ45 connector etc.

Supply, Installation, Testing & Commissioning of GI Flexible

Network Switches

Supply, installation, testing and commissioning of Layer 2 switch with 48 ports (RJ-45) including SFP modules, rack mountable, SMPS power supply & other termination accessories (Like Pigtails/LIUs/ Convertors/Splicing equipment ,Patch panel, Patch Cord, Etc) complete as per specifications and as required for BMS DDC Panel Networking. The switch to switch distance shall not exceed beyond 80 meters.

Description of Work / Item(s)

Amount

Water Supply / Transfer Pumps :

In-line, vertial multistage, centrifugal clear water pumps, speed upto 2900 rpm, with SS-304 casing, S.S 304 impeller and SS-304 shaft, C.I. Base CED coating & head, connected to a TEFC motor (with mechanical seal) suitable for 400 / 440 volts, 3 phase 50 cycles A.C. supply with 150 mm dia pressure guage with gunmetal isolation valve, vibration eliminating pads as required, M.S fabricated base plate bolted to cement concrete foundations complete. Vendor to submit performance curves and technical catalogue of the proposed model for review and information.

Electrical Starter panels complete with O/L Relay with Single phasing preventer feature, earth leakage relay, ON-OFF and Trip Indicating lamps, contactors contacts for Building Automation System, interlocking, level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level, cascade operation, working / standby slelction, etc. suitable for the motor H.P. as specified below and with provision for remote P.B. on/off complete as required. The on/off operations for all pumps shall be available on central BMS system

WATER TREATMENT FEED PUMP /TRANSFER PUMP - P1

For Transfer water Raw water tank to domestic underground water tank

Capacity per pump - 10.0 m3/hour] Head - 30.0 mt 1 Set = 3 Nos. pump (2 working+1 standby), cascade operation Approx. Elec. Load. - as per approved make of RFP Location - Pump Room Supply Installation, testing & commissioning with Set of Auto Level Sensor

For Transfer domestic underground water tank to OH wtaer tank

Capacity per pump - 10.0 m3/hour] Head - 40.0 mt 1 Set = 1 Nos. pump (1 working+1 standby), cascade operation Approx. Elec. Load. - as per approved make of RFP Location - Pump Room Supply Installation, testing & commissioning with Set of Auto Level Sensor

FWS Transfer Pump - P2

For transferring water from STP pump room to flushing water over head tank

Supply, installation, testing & commissioning of Submersible single stage single entry pumps connected to submersible motor (The motor shall be watertight according to IEC class IP 68, and incorporate class F, insulation materials to withstand a continuous operating temperature of 155 deg C) for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit with rubber diaphragm and bend, vertical discharge pipe, electrical panel with in built level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level as determined. The pump shall be provided with a lifting devise of pull chain/guide rail & G.I. heavy class rising main of 5m length including interconnecting piping, valves (Ball Valve / Butterfly), Non return valves (GM/CI) 15 m cable etc. as per requirement complete in all respects. (Pumps shall be installed in a set of two pumps One working and One standby, with cascade operation).

(Pumps suitable to handle solids upto 25 mm size with C.I. body, SS304 shaft, C.I. impeller with 15 mtrs cable, double mechanical seal).

Electrical Starter panels complete with O/L Relay with Single phasing preventer feature, earth leakage relay, ON-OFF and Trip Indicating lamps, contactors contacts for Building Automation System, interlocking, level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level, cascade operation, working / standby slelction, etc. suitable for the motor H.P. as specified below and with provision for remote P.B. on/off complete as required. The on/off operations for all pumps shall be available on central BMS system

Transfer from STP to Overhead Tank

Capacity per pump - 10 m3/hour Head - 70.0 mt 1 Set = 2 Nos. pump (1 working+1 standby), cascade operation Approx. Elec. Load. - as per approved make of RFP Location - STP Area Supply Installation, testing & commissioning with Set Og Auto Level Sensor

Basement Drainage Pumps / Mud Pumps:

Supply, installation, testing & commissioning of Submersible single stage single entry pumps connected to submersible motor (The motor shall be watertight according to IEC class IP 68, and incorporate class F, insulation materials to withstand a continuous operating temperature of 155 deg C) for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit with rubber diaphragm and bend, vertical discharge pipe, electrical panel with in built level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level as determined. The pump shall be provided with a lifting devise of pull chain/guide rail & G.I. heavy class rising main of 5m length including interconnecting piping, valves (Ball Valve / Butterfly), Non return valves (GM/CI) 15 m cable etc. as per requirement complete in all respects. (Pumps shall be installed in a set of two pumps One working and One standby, with cascade operation).

(Pumps suitable to handle solids upto 25 mm size with C.I. body, SS304 shaft, C.I. impeller with 15 mtrs cable, double mechanical seal).

Electrical Starter panels complete with O/L Relay with Single phasing preventer feature, earth leakage relay, ON-OFF and Trip Indicating lamps, contactors contacts for Building Automation System, interlocking, level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level, cascade operation, working / standby slelction, etc. suitable for the motor H.P. as specified below and with provision for remote P.B. on/off complete as required. The on/off operations for all pumps shall be available on central BMS system

Mud pump for Ramp Sump drainage - MP1 - 3000 liter capacity

Capacity/Flow Rate - 2.78 LPS (10.0 M3/Hr) Head - 30.0 mt 1 Set = 2 Nos. pump (1 working+ 1 standby), cascade operation Approx. Elec. Load. - 1.5 KW each pump RPM - 2900 MOC - C.I Casing / C.I. Impeller / S.S. Shaft Location - Ramp 35 MM Solid handling Supply Installation, testing & commissioning

Sewage Pumps with grinder:

Supply, installation, testing & commissioning of Submersible single stage single entry pumps connected to submersible motor (The motor shall be watertight according to IEC class IP 68, and incorporate class F, insulation materials to withstand a continuous operating temperature of 155 deg C) for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit with rubber diaphragm and bend, vertical discharge pipe, electrical panel with in built level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level as determined. The pump shall be provided with a lifting devise of pull chain/guide rail & G.I. heavy class rising main of 5m length including interconnecting piping, valves (Ball Valve / Butterfly), Non return valves (GM/CI) 15 m cable etc. as per requirement complete in all respects. (Pumps shall be installed in a set of two pumps One working and One standby, with cascade operation).

(Pumps with grinder system suitable to handle solids upto 25 mm size with C.I. body, SS304 shaft, C.I. impeller with 15 mtrs cable, double mechanical seal).

Electrical Starter panels complete with O/L Relay with Single phasing preventer feature, earth leakage relay, ON-OFF and Trip Indicating lamps, contactors contacts for Building Automation System, interlocking, level controller with operational mode as one pump working at low level, both pumps at high level with a hooter alarm and cut off at dry level, cascade operation, working / standby slelction, etc. suitable for the motor H.P. as specified below and with provision for remote P.B. on/off complete as required. The on/off operations for all pumps shall be available on central BMS system

Grinder pump for Basement toilet Sump drainage - SP1 - 2000 liter capacity

Capacity/Flow Rate - 2.78 LPS (10.0 M3/Hr) Head - 15.0 mt 1 Set = 2 Nos. pump (1 working+ 1 standby), cascade operation Approx. Elec. Load. - 1.5 KW each pump RPM - 2900 MOC - C.I Casing/C.I. Impeller/S.S. Shaft Location - Basement -1 STP Supply Installation, testing & commissioning

WATER TREATMENT EQUIPMENTS :

Providing, fixing, testing & commissioning of skid mounted fully automatic Reverse Osmosis System of output capacity 2000 lt./hr. designed at a minimum Flux at inlet and necessary of minimum 60-70% recovery, complete as required with the following items: (1 working ) - R.O plant at Terrace Level for Drinking purpose

Garnet Filter (GF) - 1 Nos Media for GF - 1 Lot Antiscalant Dosing System with level sensors - 1 Nos. Cartridge Filter - 1 Nos. High pressure pump - 1 Nos. R.O. Feed pump- 1 Nos. R.O. Block - 1 Nos Membranes - 2 Nos Pressure Tubes - 2 Nos SS-304 RO skid - 1 Nos pH correction system - 1 Nos Necessary instruments - 1 lot Interconnecting pipe with necessary valve work - 1 lot i) CPVC (upto HP Pump) - 1 lot ii) SS-316 (HP Pump to Membrane) - 1 lot Pressure gauges - 5 Nos Flow meter with Totalliser -2 Nos PPLC cum instrument panel - 1 Nos Conductivity Indicator - 1 Nos Level sensors (Antiscalent Tank) - H/L - 1 Nos Level sensors (Permeate Tank) - H/L- 1 Nos Control Valve (Inlet) to R.O. tank - 2 Nos Control Valve (Reject) - 1 Nos RO electrical control panel. - 1 Nos

R.O Plant SET as per above specification & Equipments

S.S.316 L ,13 mm thick EPDM Rubber insulated Storage tank of 3000 ltrs capacity installed at terrace level

Online U.V. treatment with single wave-length UV for disinfection of 3.0 cum/hr average flow; UV dosage of 300 to 400 joules/sqm, with more than 90% UVT for domestic water supply

SITC of Motorise valve - (Automatic OHT Level Control System - Butterfly Valve - IP55CB-230VAC 1) On-Off Type Electrical Actuator Single Phase 220V AC Operated Wafer Type Butterfly Valve with CI Body & amp; SS Disc2) Level Float Switch- 5M 3) Control Box - * IP 55 Finishing(250 x 160 x 115) , * LED Lamps: Tank FULL, Tank EMPTY, Power, * Power supply toggle switch, * Accepts 230V Single Phase power supply and provides 24VAC to float switch and 230VAC to valve coil., * Accepts O/NC feedback from float switch.

Description of Work / Item(s)

Amount

SITC of Metal Hexagonal Paneling 1. The material of construction and technical specification shall remain the same as per modular rigid PVC/Polyolefin metal panelling (Sr No. 1 modular rigid PVC/Polyolefin metal panelling) however in the front tiles shall have hexagonal shape and the tile’s periphery shall be made up of metal sections. 2. The structure shall allow an uninterrupted flow of wires/cable/tubes of a maximum diameter of 25mm. 3. The panel shall be designed in such a manner that it takes care of the undulation of walls and gives perfect flat surface finish and compile easy service & maintenance procedure. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Metal Printed Metal Paneling 1. The printed panelling shall have the same technical specifications as that of acoustic metal panelling (Wall Finishing - Sr No. 1 modular rigid PVC/Polyolefin metal panelling). However, in addition to it, the front tile shall be digitally printed. Graphics shall be approved by the Customer. 2. Digital printing shall be done on modular metal Panelling. Pasting stickers/flex/vinyl on metal tile shall be deemed unacceptable. 3. The structure shall be made from a modular, heavy-duty powder-coated CRCA frame (minimum sheet thickness 1mm) and shall allow an uninterrupted flow of wires/cable/tubes of maximum diameter 25mm. 4. The structure shall be securely connected from the wall, roof and floor. It shall be made up of a minimum of 1mm thick vertical slotted rolled C sections (Upright) and horizontal rolled ‘C’ connectors. Grid of the desired dimension shall be formed by Vertical and horizontal sections having 20 to 50mm pitch. 5. For Structure: - Powder coated CRCA steel sheet. (Sheet thickness minimum 1.0mm with powder coating). Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of PET Paneling 1. Computationally generated partition/paneling form made up of polyethylene terephthalate, the material shall be resistant to moisture. The elements shall be arranged in a defined pattern with proper spacing. The panels shall be fixed on bison board/painted walls/steel structure with appropriate fixing/installation method. The proposed acoustic panels shall be Greenguard Gold certified/tested (from UL/Intertek). The necessary certificate/test report valid on the bid date and to be submitted at the time of drawing approvals. The panels should be available in 9mm & 12mm thickness. Material NRC should range between NRC: 0.8 - 0.85. 2. To ensure restriction of hazardous substances; the acoustic panel/board shall be RoHS certified/tested (from UL/Intertek). The necessary certificate/test report valid on the bid date and to be submitted at the time of drawing approvals. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Paint Painting to new walls with 3 coats of plastic emulsion paint of approved brand and shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc. complete for finished item of work over one coat of primer total 3 coats. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC Wall Putty Material for 1mm thick Putty on all exposed portions of beams, columns and walls as directed by the consultants including mixing, scraping, and levelling the surface, cleaning and complete in all respects to receive the paints & finishes. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Modular rigid PVC/Polyolefin metal partition The material of construction and technical specification shall remain the same as per modular rigid PVC/Polyolefin metal panelling (Sr No. 1 modular rigid PVC/Polyolefin metal panelling) however in partition the cladding shall be done on both side of the section/grid work. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Curve/Bend Modular rigid PVC/Polyolefin metal partition The material of construction and technical specification shall remain the same as per modular rigid PVC/Polyolefin metal panelling (Sr No. 1 modular rigid PVC/Polyolefin metal panelling) however, the shape shall be a perfect curve. Partition curve shall be achieved by curved tiles only. Curvilinear arrangement using straight tiles shall be deemed unacceptable. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of modular fabric partition Flat fabric partition made up of a minimum 600mm wide by minimum 300mm high tiles fitted as per the acoustical requirement. Fabric Make: Response or equivalent. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Straight Modular Glass Partition Material 1. Full height glass partitions walls shall be made of minimum 10mm thick toughened glass. The glass shall be fixed using modular metal sections at top, bottom & sides. The section’s size shall be minimum 45 x 20mm and shall be installed on to the floor, wall and ceiling. The sections shall be used only on top, bottom, and extreme ends (adjacent to walls) only. 2. The glass partition shall be Greenguard Gold certified/tested (from UL/Intertek). The necessary certificate/test report should be valid on the bid date and to be submitted at the time of drawing approvals. NOTE: - The nature of installation shall be replaceable, expandable and flexible to cater the future expansion/technical up-gradation. 3. The modular glass partition shall have below features: 3.1 It shall be capable to accommodate horizontal/vertical raceways at any height (as instructed by EIC). 3.2 The modular glass partition system shall have inbuilt feature to insert metal panel tiles as specified in sr. no. 1 (modular rigid PVC /Polyolefinmetal panelling). This is to ensure proper integrated look of glass partition with that of adjacent paneling system and meet acoustic requirements. The metal tiles shall have micro-perforations (less than 1.6mm diameter each) all over the surface with a density of 5000 holes per square feet. This feature shall be audit certified (from UL/Intertek) on modular wall paneling tile to have clean perforations and providing smooth finish on the front fascia of tiles. The necessary certificate / test report valid on the bid date and to be submitted at the time of drawing approvals. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Bend/Curved Glass Partition Material (10mm thick toughened glass) Including full glass partitions of minimum 10 mm thick clear toughened glass, structural support system for top and bottom including holding system from RCC slab above false ceiling, including runner hung anchor fastener to fix it. Rubber interlinear & gaskets to fix bottom into SS "U" channel in floor. Silicon sealant to fill the gap. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of 12mm thick Frameless tempered clear glass Door With door spring and locking arrangements and both way handle and patch fittings. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Metallic Door with door frames/chaukhats (with OR without Vision Panel) With door hinges and locking arrangements and both way handle. Prepare with rigid thermo fused film metal panels. Specification: 0.6mm thick Metal panel sheets, internal cavity filled with adequate quantity of honeycomb. Material of the partition and that of metal door will remain the same. Material of the partition and that of metal door will remain the same. The door thickness shall be minimum 45mm and frame thickness shall be minimum 115mm. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Designer Membrane Ceiling 1. The ceiling shall be supplied with demountable translucent stretch ceiling membrane with harpoon, corners ready to install. It shall not get discoloured & sag. All joints shall be provided with appropriate interface trims to be able to demount the ceiling to access the lights. The ceiling shall be installed using ceiling aluminium suspension system, complete as per manufacturer’s installation guidelines and as per approved shop drawings in line with the design intent and approval by Architect/Engineer In-charge approval. LED strips shall be installed using custom aluminium extrusions to ensure longevity of the installation. The ceiling shall have following features and properties: - 2. Simple and maintenance friendly: Installed in a few hours and finished product shall not require any taping, spackling, or painting, and shall be easily cleanable. 3. Durable: The systems shall resist shocks and shall not crack with movement or under stretch conditions. 4. Safe: The membranes and profiles shall have passed the stringent fire and safety tests. 5. The membrane shall have been classified as non-toxic upon burning. The Flexible membrane shall be b-s1-d0 / ASTM E-84 class A tested/certified. 6. Green: Membranes shall be 100% recyclable. 7. There shall not be any welding defect on Membranes for years to come on the perimeter edging or in the seams. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Designer Metal Baffle ceiling 1. The baffles shall be made up of CRCA powder coated sheet. These baffle planks shall be bent through CNC to have dimensions as 80X50mm or as per the design approval or as per EIC approval. 2. Centre to centre distance shall be minimum 150mm. 3. Designer metal baffle ceiling shall be Greenguard gold certified/tested (from UL / Intertek). The necessary certificate / test report valid on the bid date and to be submitted at the time of drawing approvals. 4. To ensure restriction of hazardous substances; so that the final product does not contaminate the environment and we give a healthy life to our coming generations it is necessary that the metal ceiling system shall be RoHS certified/tested (from UL / Intertek). The necessary certificate / test report valid on the bid date and to be submitted at the time of drawing approvals. 5. It is well known that metal is resistant to fire as compared to wood & fabric. However, from fire and safety point of view, to ensure that the used material is not subjected to any kind of surface treatment which provokes fire. The proposed ceiling tiles shall be class A certified/tested as per ASTM e84 (from UL / Intertek) for surface spread of flame and smoke generation. This is mandatory to ensure that the materials used in the interiors do not provoke fire. The necessary certificate / test report valid on the bid date and to be submitted at the time of drawing approvals. 6. Specifications (Finish and component details) 7. Ceiling Baffle tile: minimum 0.7mm thick CRCA powder coated sheet. 8. Carrier made of 0.60 mm CRCA steel sheet, powder coated to matching baffle colour or black as directed by the Customer. Ceiling to have arrangement to fix, hang and lock the baffles of required sizes and at required intervals. the size of punched carrier would be 35x20x35mm bent channel with holes for suspension and fixing secondary channel. 9. The baffles top edge will have a flange of 5mm to fix in the carrier profile. 10. Mother C Channel: minimum 0.8mm thick CRCA steel sheet with laser cut profiles. 11. Suspension: The carriers would be placed at every 1200mm (maximum) and suspended by means of a secondary angle, channel fixed to the carrier at every 900 to 1200 mm and this secondary member in turn would be suspended by 8mm rod fixed to the slab by means of 8mm diameter, dash fastener. 12. Top clamp: 1mm thick CRCA steel Sheet for holding the threaded rod. 13. End Cap: minimum 0.75mm thick CRCA powder coated sheet. End cap similar to main ceiling baffle. 14. Entire structure will be in powder coated CRCA sheet. 15. Metal Strip where baffle planks will be hanged shall be sleek & sturdy. 16. Color: As per approval. 17. The ceiling shall have additional perforated sheet between adjacent baffles to conceal the above ceiling services (HVAC & firefighting services) and enhance the aesthetic appeal. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Designer Metal Ceiling 1. Designer metal ceiling of powder coated tiles. 2. Tiles Perforation – To achieve acoustics without deteriorating the aesthetical appeal of the office interior it is necessary that the at-least twenty five percent of the ceiling tiles have micro-perforations (less than 1.6mm diameter each) all over the surface with a density of 5000 holes per square feet. The ceiling tile to have clean perforations and provides a smooth finish on the front fascia of tiles. 3. The proposed ceiling metal tiles shall be Class A certified/tested as per ASTM e84 (from UL / Intertek) for surface spread of flame and smoke generation. This is mandatory to ensure that the materials used in the interiors do not provoke fire. The necessary certificate / test report valid on the bid date and to be submitted at the time of drawing approvals. 4. The ceiling shall have a noise absorption coefficient (NRC) value of 0.60 according to IS:8225-1987, ISO: 354-1985 and ASTM 423-90. The necessary certificate / test report valid on the bid date and to be submitted at the time of drawing approvals. 5. To ensure restriction of hazardous substances; so that the final product does not contaminate the environment and we give a healthy life to our coming generations it is necessary that the modular metal ceiling system shall be RoHS certified / tested (from UL / Intertek). The necessary certificate / test report valid on the bid date and to be submitted at the time of drawing approvals. 6. Designer metal ceiling shall be greenguard gold certified/tested from UL / Intertek. The necessary certificate / test report valid on the bid date and to be submitted at the time of drawing approvals. 7. The structure shall be made from a heavy-duty powder coated CRCA steel sheet (minimum sheet thickness 0.8 to 1.6mm). It shall be securely grouted from the roof with help of an anchor fastener and GI self-threaded rods. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Designer Metal Mesh Ceiling 1. Modular acoustic rectangular panel ceiling tiles with inbuilt mesh, made up of minimum 0.6 mm thick metal sheet. Ceiling tile shall be available in minimum 550mm x 1100mm. 2. The tiles shall be installed on ceiling understructure. 3. The tile shall permit integration of ceiling lights as per the requirement. 4. The periphery of the complete ceiling shall be covered by 100 to 500mm calcium silicate board as per the site requirement. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Designer PET Acoustic Panel Ceiling - Linear 1. Computationally generated ceiling form made up of polyethylene terephthalate, the material shall be resistant to moisture. The panels/elements shall be arranged in a defined pattern with proper spacing. The arrangement shall be held in place using the customized metal systems. The width of the polyethylene terephthalate slots shall be minimum 150mm and maximum 1700mm. Maximum single piece length shall be 3000mm. The thickness options shall be 9mm & 12mm. Material NRC should range between NRC: 0.8 - 0.85. The ceiling shall be light in weight and easy to handle. 2. The proposed PET acoustic ceiling panels shall be Greenguard Gold certified/tested (from UL/Intertek). The necessary certificate/test report valid on the bid date and to be submitted at the time of drawing approvals. 3. To ensure restriction of hazardous substances; the acoustic panel/board shall be RoHS certified/tested (from UL/Intertek). The necessary certificate/test report valid on the bid date and to be submitted along with the technical bid. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Designer Acoustic Metal False ceiling with Planks 1. Factory made acoustic modular metal false ceiling of powder coated panels. Make shall comprise of perforated and non-perforated metal panels made through CNC laser cutting, bending & punching. Panel shall be of 0.6mm CRCA sheet of approved powder coating finish. Panels shall be designed to achieve shape and design as per the design consultant with the combination of acrylic panels with lights, designed to enhance visual feel, with provision for easy installation and maintenance, integrated lighting and scope for integration of building services like HVAC and fire detection/ fighting system. Metal modular false ceiling shall have Noise absorption coefficient (NRC) value 0.60 according to IS:8225-1987, ISO: 354-1985 and ASTM 423-90. 2. It is well known that metal is resistant to fire as compared to wood & fabric. However, from fire and safety point of view, to ensure that the used material is not subjected to any kind of surface treatment which provokes fire. The proposed ceiling tiles shall be Class A certified/tested as per ASTM e84 (from UL / Intertek) for surface spread of flame and smoke generation. This is mandatory to ensure that the materials used in the interiors do not provoke fire. The necessary certificate / test report valid on the bid date and to be submitted at the time of drawing approvals. 3. To ensure restriction of hazardous substances; so that the final product does not contaminate the environment and we give a healthy life to our coming generations it is necessary that the modular metal ceiling system shall be RoHS certified/tested (from UL / Intertek). The necessary certificate / test report valid on the bid date and to be submitted at the time of drawing approvals. 4. Designer metal ceiling shall be greenguard gold certified/tested. The necessary certificate / test report valid on the bid date and to be submitted at the time of drawing approvals. 5. To avoid dark spots/areas in the room it is necessary that continuous linear lights are used across the width/length of the room. Audit certified design feature (from UL / Intertek) of integrated channel in ceiling for quick installation & replaceability of continuous linear light. The ceiling system having integrated inbuilt channel for installation of cove lights and shall permit quick and easy replacement of cove light without using any tools. Replacement to be carried out within 120 Seconds per meter. The necessary certificate / test report valid on the bid date and to be submitted aat the time of drawing approvals. 6. Seismic safety of user & room equipment is a prime concern area. The metal ceiling shall sustain the seismic vibrations as per design spectrum IS 1893 for zone 2 vibrations or better. The test shall be carried out by authorized government agency. The necessary certificate / test report valid on the bid date and to be submitted at the time of drawing approvals. 7. Structure shall be made from heavy duty powder coated CRCA steel sheet (minimum sheet thickness 0.8 to 1.6mm). Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Designer PET Acoustic Panel Ceiling - Hexagonal 1. Computationally generated ceiling form made up of polyethylene terephthalate, the material shall be resistant to moisture. The hexagonal panels/elements shall be arranged in a defined pattern with proper spacing. The arrangement shall be held in place using the customized metal systems. The diagonal width of the polyethylene terephthalate panels shall be minimum 1000mm. The thickness options shall be 9mm & 12mm. Material NRC should range between NRC: 0.8 - 0.85. The ceiling shall be light in weight and easy to handle. 2. The proposed PET acoustic ceiling panels shall be Greenguard Gold certified/tested (from UL/Intertek). The necessary certificate/test report valid on the bid date and to be submitted at the time of drawing approvals. 3. To ensure restriction of hazardous substances; the acoustic panel/board shall be RoHS certified/tested (from UL/Intertek). The necessary certificate/test report valid on the bid date and to be submitted at the time of drawing approvals. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Designer PET Chandelier Computationally generated chandelier made up of polyethylene terephthalate, the material shall be resistant to moisture. The hexagonal panels/elements shall be arranged in a defined pattern with proper spacing. The arrangement shall be held in place using the customized metal systems. The panel thickness shall be 9mm. Material NRC should range between NRC: 0.8 - 0.85. The ceiling shall be light in weight and easy to handle. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Designer Acoustic Flooring To avoid distraction of operators because of unwanted noise generated from movement of chairs/people in the control/office room it is necessary that the proposed flooring shall damp such impact noises. Acoustic flooring (shall reduce impact sound by 14dB (ISO 717-2)). It shall be twin-layer linoleum built up from minimum 2mm acoustic laminate and a 2mm corkment backing. Flooring shall be decorative type of approved shade, pattern, texture and design and of approved manufacturer. Dimensions shall be as per the final approved design and site requirement. Flooring shall be laid over concrete floor with laying compound strictly as per manufacturer’s specification. The designer acoustic flooring shall be Greenguard gold tested / certified. The necessary certificate / test report valid on the bid date and to be submitted at the time of drawing approvals. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Vitrified Flooring Fully vitrified, 8mm thick non-porous, homogenous, abrasion resistant, minimum size 600 mm x 600 mm x 8mm of approved colour and shall be laid over concrete floor with laying compound strictly as per makes given. Total thickness of the flooring shall be 40mm thick including the thickness of the tiles, under bed. Tiles will be laid with 2 mm gap using spacers and gap will be filled with black colour epoxy latictere. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Designer Privacy film for glass partitions & glass door The film to be installed on clear glass to provide the look of sandblasted glass. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Curtains for windows: Roll down curtains Supply and installation of manual roller blinds having aluminium roller tube along with fabric pasted on it with glue having control unit for manual operations and bottom bar aluminium powder coated for weight purpose, including fabric fitting and accessories of approved make and colour etc. complete. OR as per engineer approval. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Sign board 1. Providing and fixing Name plate for individual cabin and rest of the area. Signage's are made up of laser cut Anti-Corrosive high grade AISI 316 Stainless Steel of 2mm thick sheet with laser cut method for impression and with satin finish. 2. Approx. Dimensions: 300 mm X 170 mm X 2 mm. Design and detailing provided by as per engineer in charge. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of of Glass Railing Fixing of 900mm high Side Fixed Handrail system including 10-12mm clear toughened glass railing with Customized SS 304 Railing system as per Engineer in charge approval. The glass shall be held with SS 304 stud with flat headed bolt single point spider fittings as per design. The 50 diameter SS pipe shall be held firmly with the 63.5x12 mm thick SS flat vertical bar through SS bracket at every junction with M4SS set screws. The entire assembly shall be fixed through two SS connect holder brackets. The system will be Complete as per requirement of site. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Cove Lights (as per Lux Requirement) 1. It will be a continuous rail of LED light, high brightness, neutral, or warm white with wall washing applications. Its slim profile and simple daisy-chain system allows high design flexibility to form long. 2. Light source: LED 3. Light color: 6500K 4. Power consumption: 3W/m to 5W/m 5. Operating Voltage Range (V) 100 – 300 6. Operating Frequency (Hz) 50 ± 3% 7. Colour: White 8. Lifetime: 15000 burning hrs. (At L70) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Designer ceiling light Wipro Vertica 1. The light shall be premium lighting and shall be used in open ceiling spaces to create lighting effects. Surface and pendant mount provision with the help of accessories. 2. Aluminium Body Powder Coated in White or Black 3. Clean diffuser 4. High power high lumen output LED 5. High efficiency reflector optics 6. Effective thermal management 7. OR 8. As per EIC approval. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of designer ceiling light Wipro Celeste 1. High Efficiency Translucence (HET) diffuser. Housing made up of fiberreinforced plastic outer surface painted. High efficacy LEDs. Diffused Glass dome. 2. OR 3. as per EIC approval. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of designer ceiling light Wipro Orbit 1. High efficacy and long-life LEDs 2. Housing made of CRCA and white matt powder coated 3. High Efficiency Translucence (HET) diffuser made of PMMA (acrylic) milky white 4, Suspension system made of steel wire of 2mm dia and accessories are chrome plated Or conduit made of MS pipe and white powder coated 5, Easy to mount on true ceiling and quick to service. 6. OR 7. As per EIC approval. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Reception Counter 1. The furniture work surface shall be straight in shape to maintain grand aesthetic appeal. It shall be made of minimum 25mm thick MDF finish with molded PU edge on the working side. 2. The understructure shall be minimum 18mm thick MDF board. 3. It shall have provision of electrical and Lan sockets with concealed wiring. 4. Design as per engineer in charge approval. Approximate minimum Dimensions – 3000mm(W) X 750mm(D) X 750mm(H). Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of 3-Seater Sofa The top shall be of Upholstery with PU Finish. The sofas are made of solid wood base, reinforced with supportive addendum in the seat. Engineered wood panels form/support the overall design structure, they synergise with the solid wood to offer unparalleled life to the product. Foam padding of multi-density and varying thicknesses provide cushion for the sofa. PU foam used is made Hennecke foam plants using German Technology capable of producing the high-quality flexible polyurethane foam. It provides unparalleled comfort, ease of use and durability. The foam used is 32 Density for seating areas and 28 Density for backrest. The supersoft foam used is in seating areas in 32-35 Density High-resilience (HR) foam which is unique and rarely used by manufacturers. Webbing: Interwoven high tensile elastic bands for optimum comfort and endurance. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of 2-Seater Sofa The top shall be of Upholstery with PU Finish. The sofas are made of solid wood base, reinforced with supportive addendum in the seat. Engineered wood panels form/support the overall design structure, they synergise with the solid wood to offer unparalleled life to the product. Foam padding of multi-density and varying thicknesses provide cushion for the sofa. PU foam used is made Hennecke foam plants using German Technology capable of producing the high-quality flexible polyurethane foam. It provides unparalleled comfort, ease of use and durability. The foam used is 32 Density for seating areas and 28 Density for backrest. The supersoft foam used is in seating areas in 32-35 Density High-resilience (HR) foam which is unique and rarely used by manufacturers. Webbing: Interwoven high tensile elastic bands for optimum comfort and endurance. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Single Seater sofa chair Single Seater sofa chair without Arm, SS Base Stand, Gas Lift, Leatherette Tapestry. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Chat chair / Hot Seat 1. It shall have acoustic wrapped fabric fully upholstered on inner and outer side. The entire inside structure shall be made of aluminium frame. It should be designed with Ergonomics in mind. 2. The fabric shall be washable, appropriate for task seating and should withstand normal wear and tear. Fabric Make: Camira (Sprint) / Sunbury / Kvadrat / Response OR Equivalent. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Center unit (Type 1) 1. Centre unit for sofa, toughened glass, 12mm thick, chrome plated pipe frame. 2. Approximate minimum dimensions – 1200mm(W) X 600mm(D) X 450mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Center unit (Type 3) 1. 18mm thick MDF top for center unit for sofa with injection molded polyurethane nosing on profiled wooden core. 2. Understructure shall be made up of laminated board / sheet metal. Approximate minimum Dimensions – 600mm(Dia) / 600(W) X 600mm(H)Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Chair Type 1 High Back with Mesh Backrest, Adjustable Armrest, Gaslift for seat height adjustment, Standard 5-prong nylon base, Seat: Fabric, Backrest – Mesh Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Chair Type 2 Medium Back, Mesh Back, Silver Epoxy Backbone, Synchronized Mechanism, 3-Way Adjustable Armrest, Gaslift for Seat height adjustment, Standard 5-prong nylon Base, Seat - Fabric and mesh backrest. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Chair Type 3 Low back visitor model ABS for seat, Mesh back with extra lumber Support with fine tuning for depth adjustment, with fixed armrest, silver epoxy cantilever base Upholstery: Black Fabric Seat & mesh backrest. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of workstation Desk (Type 1) 1. Linear shape tabletop shall be of 25 mm thick MDF board. 2. The working side edge: - Audit certified design (from UL / Intertek) feature on front modular Polyurethane (PU) Edge. High density Poly Urethane Foam moulded on industrial grade aluminum core to form minimum 50mm deep tapered edge to be installed on worktop. The edge shall be mechanically replaceable within 30 minutes in case of damage or wear without opening or removing the top. The necessary certificate / test report valid on the bid date and to be submitted at the time of drawing approvals. 3. Legs: Ergonomically designed and matching with the open office concept. The leg is made out of sheet metal. 4. The screen shall be made of minimum 8mm thick frosted acrylic or fabric panel. 5. Under structure pipe shall be made up of minimum 1.6mm thick CRCA Laser cut components, powder coated with the matching shade/color/finish. 6. Cable tray: Shall be made up of 1mm thick CRCA sheet, Cable tray is used for running the wires between the desk. Provision of switch socket and wire flow can be made as per requirement of Engineer in charge. 7. Accessories: Flap with SITC of 2 nos 16 A modular switch , 3 Nos 16 A modulat socket and 1 nos cat-6A IO point . 8. The desk shall be Greenguard gold tested/certified (from UL / Intertek). The necessary certificate / test report valid on the bid date and to be submitted at the time of drawing approvals. Approximate minimum Dimensions – 1200mm (W) X 600mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Metal Storage Versatile 3-drawer office storage system solution shall be made up of 0.8mm ‐ 1mm CRCA sheets with powder coated finish. The drawers are meant to store stationary items like pens, calculators, staplers, files, folders, documents etc. It comes with sliding drawers and single lock operation along with caster wheels for 360‐degree movement. The storage shall be greenguard gold tested/certified (from UL / Intertek). The necessary certificate / test report valid on the bid date and to be submitted at the time of drawing approvals. Approximate minimum Dimensions – 420mm(W) X 450mm(D) X 550mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Metal Storage Flat pack made up of minimum 0.6mm CRCA powder coated finish with hinged doors and adjustable shelves for different file heights. The storage shall be greenguard gold tested/certified. The necessary certificate / test report valid on the bid date and to be submitted at the time of drawing approvals. Approximate minimum Dimensions – 900mm(W) X 450mm(D) X 1200mm(H). Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Cabin desk 1. The furniture top shall be made up of minimum 25mm thick MDF board. 2. The working side edge: - Audit certified design (from UL / Intertek) feature on front modular Polyurethane (PU) Edge. High density Poly Urethane Foam moulded on industrial grade aluminum core to form minimum 50mm deep tapered edge to be installed on worktop. The edge shall be mechanically replaceable within 30 minutes in case of damage or wear without opening or removing the top. The necessary certificate / test report valid on the bid date and to be submitted at the time of drawing approvals. 3. The under structure and complete structure shall be made up of 18mm thick MDF board / MS powder coated finish. (As per EIC approval). 4. The furniture is equipped with handles for easy opening along with soft closing drawers. The Construction shall be of high quality MDF board. 5. The furniture top shall have power box with access flap having SITC of 2 nos 16 A modular switch , 3 Nos 16 A modulat socket and 1 nos cat-6A IO point for wire management. The design shall be as per attached image and as per the Engineer in charge approval. 6. The desk shall be Greenguard gold tested/certified (from UL / Intertek). The necessary certificate / test report valid on the bid date and to be submitted at the time of drawing approvals. 7. Approximate minimum dimensions Furniture Top – 2100mm(W) X 750mm (D) X 750mm(H) Side Runner – 900mm(W) X 450mm(D) X 750mm(H) Back Runner – 2100mm(W) X 450mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Open Collaborative conference table It shall be designed for minimum 4 / 6 / 8 people; it shall have acoustic wrapped fabric fully upholstered on inner and outer side. The countertop at the center shall have laminate finish. The edges shall have 40-50 mm deep molded polyurethane edge. The entire structure shall be self-standing without any need of grouting. It should be designed with Ergonomics in mind. It should have integrated power socket under seat as per approval and direction of Engineer incharge . The fabric shall be washable, appropriate for task seating and should withstand normal wear and tear for 5 years. Fabric Make: Camira (Sprint) / Sunbury / Kvadrat / Response. Approximate minimum Dimensions – 2700mm(W) X 1500mm(D) X 1800mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Meeting table Furniture 1. The furniture top shall be made up of minimum 25mm thick MDF board with molded Polyurethane (PU) Edge. 2. The understructure shall be made up of sheet metal. Approximate minimum Dimensions – 1000mm (Diameter) X 750mm(H) / 1000mm(W) X 1000mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Conference/meeting room furniture for (13 Pax) 1. The conference/meeting room furniture shall conform to high standard of engineering as mentioned in the document; meeting the specified codes, standards and designs. 2. The furniture top shall be made up of minimum 25mm thick MDF board with molded Polyurethane (PU) Edge. 3. The under structure shall be made up of 18mm thick MDF board with 2mm thick PVC edge banding tape / Legs: Ergonomically designed and matching with the open concept. The leg is made out of sheet metal. 4. Accessories: 6 to 7 Flap each having provision and SITC of 2 nos. 16 A modular switch and 3 nos modular socket with 2 nos cat-6A IO port , wireflow and cable tray should have as per approval and direction of engineer in charge. 5. Cable Trays and Wiring: - The furniture shall be designed with cable trays to allow for continuous & concealed cable management across the furniture. Approximately minimum Dimensions – 5200mm (W) X 1800mm (D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Conference/meeting room furniture for (17 Pax) 1. The conference/meeting room furniture shall conform to high standard of engineering as mentioned in the document; meeting the specified codes, standards and designs. 2. The furniture top shall be made up of minimum 25mm thick MDF board with molded Polyurethane (PU) Edge. 3. The under structure shall be made up of 18mm thick MDF board with 2mm thick PVC edge banding tape / Legs: Ergonomically designed and matching with the open concept. The leg is made out of sheet metal. 4. Accessories: 8 to 9 Flap each having provision and SITC of 2 nos. 16 A modular switch and 3 nos modular socket with 2 nos cat-6A IO port , wireflow and cable tray should have as per approval and direction of engineer in charge. 5. Cable Trays and Wiring: - The furniture shall be designed with cable trays to allow for continuous & concealed cable management across the furniture. Approximately minimum Dimensions – 6800mm (W) X 1800mm (D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Conference/meeting room furniture for (19 Pax) 1. The conference/meeting room furniture shall conform to high standard of engineering as mentioned in the document; meeting the specified codes, standards and designs. 2. The furniture top shall be made up of minimum 25mm thick MDF board with molded Polyurethane (PU) Edge. 3. The under structure shall be made up of 18mm thick MDF board with 2mm thick PVC edge banding tape / Legs: Ergonomically designed and matching with the open concept. The leg is made out of sheet metal. 4. Accessories: 10 to 11 Flap each having provision and SITC of 2 nos. 16 A modular switch and 3 nos modular socket with 2 nos cat-6A IO port , wireflow and cable tray should have as per approval and direction of engineer in charge. 5. Cable Trays and Wiring: - The furniture shall be designed with cable trays to allow for continuous & concealed cable management across the furniture. Approximately minimum Dimensions – 7600mm (W) X 1800mm (D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Conference/meeting room furniture for (23 Pax) 1. The conference/meeting room furniture shall conform to high standard of engineering as mentioned in the document; meeting the specified codes, standards and designs. 2. The furniture top shall be made up of minimum 25mm thick MDF board with molded Polyurethane (PU) Edge. 3. The under structure shall be made up of 18mm thick MDF board with 2mm thick PVC edge banding tape / Legs: Ergonomically designed and matching with the open concept. The leg is made out of sheet metal. 4. Accessories: 12 to 13 Flap each having provision and SITC of 2 nos. 16 A modular switch and 3 nos modular socket with 2 nos cat-6A IO port , wireflow and cable tray should have as per approval and direction of engineer in charge. 5. Cable Trays and Wiring: - The furniture shall be designed with cable trays to allow for continuous & concealed cable management across the furniture. Approximately minimum Dimensions – 9400mm (W) X 1800mm (D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Dining Counter 1. The dining furniture shall have granite top of minimum 12mm thick. 2. The understructure shall be made up of stainless steel (SS304). Approximate minimum Dimensions – 1050mm(W) X1050mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Dining counter 1. The dining furniture shall have granite top of minimum 12mm thick. 2. The understructure shall be made up of stainless steel (SS304). Approximate minimum dimensions – 1800mm(W) X 800mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of VIP dining counter 1. The dining counter shall have veneer with PU matt finish. The structure shall be made up of veneered MDF/ply structure with matt finish. Approximate minimum dimensions – 6200mm(W) X 2100mm(D) X 750mm(H) Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of Dining Chairs without arm, PP/Fiber with steel base. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

SITC of VIP Dining Chairs Chair shall be made up of solid teak wood with matt finish, with artificial leather upholstery with appropriate cushion. Detailed specifications and mode of execution is mentioned in technical Specification of RFP.

Description of Work / Item(s)

Amount

PART A- Supply and fixing of grey bijolia stone (20mm TH.), on Toe Wall coping (dressed and polished) in all respect. Base rate: Bijolia stone (20mm TH.) - INR 950 per sq.m

PART B- Supply & installation of marine grade polysteel modular GAZEBO, rectangular shape & elevation as per the attached design, made of UV stabilized class-1 fire retardant polyster composite with glass fibre reinforcement of 750GSM, self coloured, textured surface finish with scratch resistant aliphatic grade UV stabilized polyurethane paint; Inner frame work made of mild steel ; All hardwares are to be of ms. To be \individually hand crafted to replicate steel and cast iron and to be installed with ground using foundation bolts. as per conceptual picture attached RFP.Each structure of aprox. 5000 kg

PART C-- Supply & installation of marine grade polysteel modular PERGOLA, rectangular shape & elevation as per the attached design, made of UV stabilized class-1 fire retardant polyster composite with glass fibre reinforcement of 750GSM, self coloured, textured surface finish with scratch resistant aliphatic grade UV stabilized polyurethane paint; Inner frame work made of mild steel hot dip galvanized; All hardwares are to be of stainless steel. To be \individually hand crafted to replicate steel and cast iron and to be installed with ground using foundation bolts as per conceptual picture attached RFP. Each structure of aprox. 500 kg

Supply & installation of Wrought iron and mild STEEL WELDING WORK using angles, square bars, tees and channel grills, grating frames, gates and tree guards of any size and design etc. including cost of screens and welding rods or bolts and nuts complete fixed in position but without the cost of excavation and concrete for fixing which will be paid separately .

Supply and fixing of Pergolas in 100 *50 mm MS hollow sections; including MS posts of 100 *100 mm duly fixed and bolted with red oxide and painted in specified colour.Each structure of aprox. 2000kg

PART-D- SITTING DETAILS (12 No.) Supply and fixing of aluminium extrude section of 100mm x 50mm (in black(RAL) finish powder coated) closed with cap on both edges.

PART E --SITTING DETAILSS (2 No.)--Providing and fixing of black granite(18mm TH.) of honed finish on brick Wall cladding (external face of sitting area), including coping ,clamps and grooves complete in all respect as per Conceptual pictures attached with RFP Base rate: Black granite (18mm TH.) - INR 1500 per sq.m

PART- G- Indoor/Outdoor Pots--Supplying and fixing of potted plants FRP POTS (from CREDO or similar) including cost of cocopit,complete in all respect as per following details:

CSW 5.1 (POLISHED BLUE)_ROU COMPE(22" dia and of 15.40"height) Base rate: FRP POT INR 5568 per piece

CSW14.1 (DA GREY)_ATTR VIS (22" dia and of 30"height) Base rate: FRP POT INR 12149 per piece

CSW 19.2 (DA GREY)_ED RAD(09" dia and of 19"height) Base rate: FRP POT INR 5568 per piece

CSW 23.1 (DA GREY)_CAV SLI(30"x25" and of 14"height) Base rate: FRP POT INR 8515 per piece

PART-H Horticulture Works--Supplying and planting of trees , shrubs , hedges, palms, groundcovers, creepers etc. including digging of pits , refilling with manure & good earth , anti termite treatment for following plants:

Date Palm (8' stem)

Plumeria Alba (8'-10')

Terminalia (12')

Tabebuia Avellanedae (10')

Tabebuia Argentea (10')

Erythrina Indica (8')

Bahunia Blakeana (10')

Murraya exotica (2')

Bougainvelia Globra (1')

Jatropha (2')

Tecoma Gudhi Choudhi(4')

Calliandra (3')

Nerium drawf (1')

Bombex ceiba (12')

Fountain grass (2')

Spaider Lily (1')

Pandanus grass (6")

Zephyranthus Lily (4")

Ixora Singapornisis (3')

Chandini Dwarf (1')

Hibiscus(1')

Tecoma dwarf (1')

Lecophyllum (1')

Supplying, planting of POTTED PLANTS for following plants:

Bougainvelia (4')

Plumeria Singapuri(4')

Ficus Panda(5') In toppery bunches

TRIANGULAR Palm(5')

Phonix Palm(4')

Supplying, proper storage and laying of COCOPIT each bag of 25 kg.

Supplying and laying of VERMI COMPLAST each bag of 50 kg

Providing and laying of BROWN GRAVEL with rammed earth and base(0'-4" HT. OF GRAVEL BED) in pavement area.

Providing and laying of PEBBLE in black and grey color of 60-75mm approx.

SITC of WATER FOUNTAINS (01 NOS) comprising of following items:

Providing and laying of Random rubble dry stone Kharanja as under base.

providing and installation of Kota / grey bijolia stone 20mm thk slabs exposed face dressed and rubbed.

Supply, installation, Testing , commissioning of water fountain of 3.00mtrX3mtr with following item and specifications with complete internal plumbing (cpvc pipe and fitting for water feature )and electrical works for following items:

WFNSeries-nozzle , Type:geyser nozzle for back stage , size 1/2" of SS finish

Angular Valve

WSP Series Submersible pump: 3 phase (kirloskar make) ,WSP 5.00(5HP-SP/60KLPH)

WLED Series LED Light :WLED 12W-12V (warm white or 3000k)(IP:69)

WEB Series ABS Eye Bull Nozzle of black of EMAUX make.

WCP-EP Series Electric Control Panel with suitable accessories :Automation on/off, indicator , switches,analog ameter, voltmeter, lux, fariles MCB, OLR and Connector etc of make L&T or equivalent

WLT SeriesLED Transformers:operating voltage12vDC-12W

Supply & installation of marine grade polysteel modular feature wall, rectangular shape & elevation as per the attached design, made of UV stabilized class-1 fire retardant polyster composite with glass fibre reinforcement of 750GSM, self coloured, textured surface finish with scratch resistant aliphatic grade UV stabilized polyurethane paint; Inner frame work made of mild steel hot dip galvanized; All hardwares are to be of stainless steel. To be \individually hand crafted to replicate steel and cast iron and to be installed with ground using foundation bolts. as per conceptual picture attached RFP.Each structure of aprox. 2500 kg

PART J- SIGNAGE--Supply and installation of ARTISTIC SIGNAGE (white marble stone of 1500mmx2100mm 200mm th with water jet cutting of 12 mm filled with antique brass finish of 16gauge thick)with proper bed preparation in ramped soil with 100 mm M20pcc.

TOTEM SIGNAGE: Design, composition, Supply and installation of structural steel frame made out of medium duty 50mm square pipe section, red oxide primer with two coat of synthetic enamel painting, providing and fixing 3/4mm thick polycarbonate sheet with 40% transluency, with graphics on single side digitally printed on UV cured 3M media or 3M external grade binly totens to be intenally illuminated with LED paower module double side, high output 7100k numbers as perdsign, 140 degree at the distance .

PART - K IRRIGATION- SITC of Irrigation system for following items:

Piping Network - PVC Providing fixing , installation and testing with trenching and Back filling mainline 600 mm and Submain 450 mm in depth of PVC pipes (IS:4985- 88), and fittings & Accessories like tees, elbows, bends, junctions, Reducers etc of 10kg/cm2 pressure; as required/directed at site for following items

PVC Pipe 90 mm x 6 kg/cm2

PVC Pipe 75 mm x 6Kg/cm2

PVC Pipe 63 mm X 6kg/cm2

PVC Pipe 50 mm X 6kg/cm2

PVC Pipe 40 mm X 6kg/cm2

Filteration Unit SITC of Disc Filter, 80/110 Micron with all required Accessories

Providing and Fixing of Manual Cleaning Screen Filter capacity of 50 m3/h 3"

Providing and Fixing of G.I. Header with 3 Butterfly Valve

Providing and Fixing of Road Sleeve of various sizes

Trenching & Back Filling with Installation Charges of 450mm x600m with compacting of soil base

PART -L STONE BOULDERS- Providing and laying of 4-5 Tonns of weight of stone boulders (random shaped) on ramped earth( with M15 PCC)as per approval . Rough stone marble/granite boulder Base rate: INR 10000 per piece

PART - M GEBION WALL- SITC for following items as per details given below:

Providing and installation of MS steel work welded,in built up sections framed work including cutting,hoisting, fixing in position and applying priming coat of redlead paint in columns, beams and joists, channels , anglestees plates with connecting plates or angle cleats.

Supply and installation of 40 -100mm dia. Pebbles contained in wire mesh structure for gabion wall.

Supply and installation of Wire mesh (60 mmx80 mm)2 mm dia wire & 2.2 mm binding wire 12 guage containing pebbles.

PART - N DRIVEWAY STONE & KERB STONE-- Providing & fixing of precast cement concrete interlocking paver blocks of M30 grade 60 mm thick from Unistone/VYARA/or equivalent to be laid and the joint is to be filled with fine sand complete in all respect .( of colour black/grey/light grey as per direction of engineer in charge) as per following details:

100 MMX 100MMX60 MM paver blocks Base rate: - INR 100 per sq.m

200 MMX 200MMX60 MM paver blocks Base rate: - INR 140 per sq.m

100 MMX 100MMX60 MM grass paver blocks Base rate: - INR 50 per sq.m

supplying and fixing of Granite (18mm TH.),as per specifications and standards in drawings. (R.BLACK , JEERA WHITE )sand blast finish. Base rate: R.Black granite (18mm TH.) - INR 1500 per sq.m JEERA WHITE granite (18mm TH.) - INR 1600 per sq.m

Providing & laying at or near ground level , factory made kerbstone of M-25 grade cement concrete, in position to the required line, level and curvature , jointed with cement mortar 1:3 including making joints with or withour grooves as specified in drawing. (450mmx300mmx200mm th)

PART -O CANOPY- Supply & installation of marine grade polysteel modular CANOPY, rectangular shape & elevation as per the attached design, made of UV stabilized class-1 fire retardant polyster composite with glass fibre reinforcement of 750GSM, self coloured, textured surface finish with scratch resistant aliphatic grade UV stabilized polyurethane paint; Inner frame work made of mild steel hot dip galvanized; All hardwares are to be of stainless steel. To be \individually hand crafted to replicate steel and cast iron and to be installed with ground using foundation bolts as per conceptual picture attached RFP. Each structure of aprox. 3000 kg

Supply & installation of tensile fabric on ms structure as per given reference & specification given in RFP

PART -P BOUNDRY WALL

Providing and fixing of grey granite(18mm Thk.) on boundry Wall (external face ), including coping ,clamps and grooves complete in all respect Base rate: Black granite (18mm TH.) - INR 1500 per sq.m

Supply & installation of marine grade polysteel, rectangular shape & elevation as per the attached design, made of UV stabilized class-1 fire retardant polyster composite with glass fibre reinforcement of 750GSM, self coloured, textured surface finish with scratch resistant aliphatic grade UV stabilized polyurethane paint; Inner frame work made of mild steel hot dip galvanized; All hardwares are to be of stainless steel. To be \individually hand crafted to replicate steel and cast iron and to be installed with ground using foundation bolts. as per conceptual picture attached RFP.Each structure of aprox. 33 kg

PART -Q ENTRANCE FEATURE ELEMENT- Providing and fixing of black & grey granite(18mm Thk.) at entrance feature (element) as per conceptual picture attached RFP, including coping ,clamps and grooves complete in all respect Base rate: Black granite (18mm TH.) - INR 1500 per sq.m Grey granite (18mm TH.) - INR 1100 per sq.m

PART -R LANDSCAPE LIGHTS- SITC for following items as per details given:

BOLLARDLED : 12W HOLDER : E27 MATERIAL : DIE CATSING ALUMINIUM WITH PC DIFFUSER BODY COLOUR : GRAPHITE GREY UPPER DIA : 122MM HEIGHT : 500MM MAKE: K-LIGHT, JAGUAR Base rate: INR 10000 per piece

SPIKE : spike / surface mounted tree up lighter made of pressure die cast aluminium Light Source : 12w Led Dimension : Dia - 90mm Length - 100mm Height 420mm IP65 MAKE: K-LIGHT, JAGUAR Base rate: INR 3500 per piece

WALL LIGHT: Wall mounted up and down light made of pressure die cast aluminium, Wattage: 2 X 3w Led Control Gear: High Power LED Driver Body: Pressure Die Cast Aluminium Finish: Powder Coated Black Protection: IP65 MAKE: K-LIGHT, JAGUAR Base rate: INR 4500 per piece

POST TOP LIGHT: Decorative Post top light complete with 40W LED MAKE: K-LIGHT, JAGUAR Base rate: INR 11500 per piece

DECORATIVE MS Pole TopDia:75mm, with 60 mm nipple Top height : 3000mm Thickness:3mm . Height:2000mm Bottom dia;114mm thikness;4.2 mm Botom Height:1000mm. with alluminium amblishment. with inside junction box Mounting base plate 250 mm dia10mm Approx 40 kg pole PU Painted in any colour( p.uMRF) painted as per client req.) MAKE: K-LIGHT, JAGUAR Base rate: INR 13000 per piece

STRIP LIGHTS: 9W NEON FLEX LED STRIP LIGHTS MAKE: NEO NEON/LEDVANCE

Description of Work / Item(s)

Amount

AUDIO SYSTEM

Ceiling Speakers Supply, Installation, Testing & Commissioning of Two-way, Ceiling-mount loudspeaker with back can. Continuous Power - minimum 30 Watts or better, Sensitivity- minimum 89 dB SPL or better, Coverage Angle -110° or less, Maximum Peak SPL - minimum 110 dB or better, Rated Impedance - 8 Ohms. Transformer Tapping - 70V/100V(30,15,7.5watts) or better. Transducers - LF - mimimum 6.5-inch or better, HF- .86-inch coaxially mounted with LF or better, Should include OEM supplied mounting brackets.

Amplifer for Ceiling Speakers: Supply, Installation, Testing & Commissioning of 4 channel class-D amplifier with 60 watts/channel into Low-Z loads.4 channels can also be bridged in pairs, each pair providing up to 100 watts rms into 4 /8 ohms or 125 watts rms into 70V/100V. Signal to Noise (A weighted, 20 Hz-20 kHz)->100 dB, Frequency Response-20 Hz - 20 kHz, Input Sensitivity-1.23 Vrms (+4 dBu), Input Impedance->10 kΩ (balanced), >10 kΩ (unbalanced), Front Panel Indicators-Power, per channel Signal, per channel Protect/Limit, Controls- 4Ω/8Ω/70V Bridge Highpass On/100V Bridged Highpass on per channel pair. Size half RU.Mounting hardware included

Amplifer for Ceiling Speakers: Supply, Installation, Testing & Commissioning of 4 channel class-D amplifier with 60 watts/channel into Low-Z loads.4 channels can also be bridged in pairs, each pair providing up to 100 watts rms into 4 /8 ohms or 125 watts rms into 70V/100V. Signal to Noise (A weighted, 20 Hz-20 kHz)->100 dB, Frequency Response-20 Hz - 20 kHz, Input Sensitivity-1.23 Vrms (+4 dBu), Input Impedance->10 kΩ (balanced), >10 kΩ (unbalanced), Front Panel Indicators-Power, per channel Signal, per channel Protect/Limit, Controls- 4Ω/8Ω/70V Bridge Highpass On/100V Bridged Highpass on per channel pair. Size half RU.Mounting hardware included

Digital Signal Processor : Supply, Installation, Testing & Commissioning of Digital Signal Processor with minimum 16 Mic/Line inputs and 8 Line outputs. Shall support phantom power on each microphone input. AEC channels - 16 or more with 200ms tail length. GPIO Ports - 16 (GPI) x 16 (GPO) ports for microphone integration. Minimum 8x8 Dante channels and support for up to 128x128 Network audio channels via Dante /AES67 or similar protocol. POTS and SIP Softphone integration for Audio conferencing. USB-B port supporting AV USB Bridging for software or web-based conferencing applications emulating USB Audio (Speakerphone) and USB Video (Camera) driver. Should have Inbuilt 16 Multitrack Player capacity. Should have 24 bit-A/D-D/A converters or better, 48 kHz Sample rate or better, Input frequency response of 20 Hz to 20 kHz or better, Input dynamic range > 109 or better.

Digital Signal Processor : Supply, Installation, Testing & Commissioning of Digital Signal Processor with minimum 8 Mic/Line inputs and 4 Line outputs. Shall support phantom power on each microphone input. AEC channels - 8 or more with 200ms tail length. GPIO Ports - 8 (GPI) x 8 (GPO) ports for microphone integration. Minimum 8x8 Dante channels and support for up to 64x64 Network audio channels via Dante /AES67 or similar protocol. SIP Softphone integration for Audio conferencing. USB-B port supporting AV USB Bridging for software or web-based conferencing applications emulating USB Audio (Speakerphone) and USB Video (Camera) driver. Should have Inbuilt 16 Multitrack Player capacity. Should have 24 bit-A/D-D/A converters or better, 48 kHz Sample rate or better, Input frequency response of 20 Hz to 20 kHz or better, Input dynamic range > 109 or better.

Boundary Layer Microphone : Supply, Installation, testing and commissioning of boundary layer table Microphone, it should be pre-polarised condenser microphone having Cardioid or better polar pattern, shall have frequency response of 42Hz to 20kHz, Should have Max SPL Level of 135dB or more, it should support phantom power, Should have sensitivity of 10mV/PA or better and dynamic range of 111db(A), Should come with mute/unmute button, should have muted/unmuted status LED Indication and Logic output for third party integration for control camera etc complete required as per the specifications.

DISPLAY SYSTEM

Interactive Main Display - 85"/86": Supply Installation , Testing and comissioning of Interactive Display 85"/86 4K UHD(3840x2160)LED Display with min 350 Cd/m2 brightness or better, contrast ration : 1200:1 , Aspect ration: 16:9, Viewing angle 178 h/v . Response Time : 8ms, Input Ports : 3xHDMI, 1xVGA, 3xUSB 2.0, 3xUSB 3.0, Output Ports :Audio Out / Optical Output, , Touch Out(2),Audio Output : 2x10wBuilt in SOC :Dual core A73+Dual core A53 , 3GB DDR,32GB Storage ,Certification:CB / NRTL,FCC Class "A" / CE,RoHS , BIS ,ISO9001,ISO14001,OHAS-18001/ISO 45000:1 for India factory ,Should include mounting as per site

VIDEO,SWITCHING & INTERFACE SYSTEM

HDMI Encoder and Decoder Set : Supply, Installation, Testing & Commissioning of 1G HDMI Video Encoder & Decoder sets. HDMI Inputs - Minimum 6 or more, HDMI Outputs - Minimum 2 or More. Encoder & Decoder should support resolution-upto 4K60 4:4:4, Power - PoE and AUX PSU. Ports Connections - RS232, GPIO/IR, Analog Audio Inputs & Audio Output, should have USB-B/C port for for AV-USB Bridging emulating USB Audio (Speakerphone driver) and USB Video (Camera driver) for software or web based conferencing applications. Content Protection: HDCP 2.2 compliant, EDID Managament. Dante/AES67 or similar network Audio Support. Mounting accessories should be included. NOTE : USB-B/C for Software or web based Conferencing can be added by required additional hardware to fulfill the requirement to have the functionality on total 2 USB connections. Encoder and Decoder system should be able to create and fulfill the requirement of 6x2 matrix switching system with mentioned functionality and should be from same OEM.

All in one HDMI Matrix Switcher : Supply, Installation, Testing & Commissioning of 4K HDMI Matrix Switcher with HDMI Inputs Minimum 3 or more, HDMI Outputs - Minimum 2 or More. The Switcher should support resolution-upto 4K60 4:4:4, Power - PoE and AUX PSU. The switcher should have Stereo Analog Audio Input and Output on 3.5mm connection, Built-in Audio de-embedding, PowerPorts Connections - RS232, GPIO/IR to control 3rd party AV equipments. Switcher should have USB-B/C port for for AV-USB Bridging emulating USB Audio (Speakerphone driver) and USB Video (Camera driver) for software or web based conferencing applications. Content Protection: HDCP 2.2 compliant, EDID Managament. Dante/AES67 or similar network Audio Support. Mounting accessories should be included. The switcher should have required no. of RS-232, GPIO, LAN Ports to control the devices mentioned in BOQ with perpetual licenses to connect Wall/Table mount touch screen controllers and iOS and Windows devices as wireless touch controller. The equipment supplied with perpetual licenses to control required AV equipment through touch panel. Note: Additional component from same OEM shall be added to meet the requirement

Cable Manager for Table : Supply, Installation, Testing & Commissioning of Table Mount enclosure with 1xHDMI and 1xUSB with F-pigtail connectors and 2 x Universal Power sockets. Manually open and close lid with Black and Clear anodize color options.

CONTROL SYSTEM & ROOM SCHEDULING

AV Control System : Supply, Installation, Testing & Commissioning of Hardware or Software based control system with required ports to control the devices mentioned in BOQ with perpetual licenses to connect Wall/Table mount touch screen controllers and iOS and Windows devices as wireless touch controller. The hardware should be such that fulfills the requirements of site.

Touch Panel with Docking station : Supply Installation Testing & Commissioning of Touch Control System with 8" or bigger Touch panel for Table Mounting, to control AV equipments & secondary wireless control on 9" or more IPAD & complete with perpetual software and licenses for IPAD

Network Switch : Supply, Installation, Testing & Commissioning of 12 port L3 Gigabit POE+ Network Swicth with Multicast support with IGMP V1/V2, QoS support, IPV4/IPV6 Support, Switching Capacity in Gigabits per Second, 1 Gbps Non-blocking ports with standard accessories. 8x1G PoE+ 125W 2x1G and 2xSFP Managed Switch

Dual band Wifi Access Point

CABLE, CONNECTORS, ACCESSORIES

HDMI Cables : Supply, Installation, Testing & Commissioning of 18Gbps 50-feet HDMI Cable.

HDMI Cables : Supply, Installation, Testing & Commissioning of 18Gbps 15-feet HDMI Cable.

HDMI Cables : Supply, Installation, Testing & Commissioning of 18Gbps 6-feet HDMI Cable.

Speaker Cable : Supply, Installation, Testing & Commissioning of 2 core 2.5 sqmm PVC Sheathed loudspeaker cable.

Microphone Cable: Supply, Installation, Testing & Commissioning of 2 core shielded balanced microphone cable.

CAT6 Cables Supply, Installation, Testing & Commissioning of Cat6 Cable for AV Network connectivity .

USB A-B Cable : Supply, Installation, Testing & Commissioning of 15" Hight speed USB A-B 3.0 Cables

USB A-B Cable : Supply, Installation, Testing & Commissioning of 6" Hight speed USB A-B 3.0 Cables

Description of Work / Item(s)

Amount

Supplying, installing, commissioning of Water Cooled Screw Chillers each complete with 160 TR actual capacity Screw compressor with motor with Unit Mounted VFD, water cooled condenser, Multiple pass evaporator and condenser, insulated chiller, flow switch at chiller and condenser, vibration isolators, integral refrigerant piping and wiring, Control panel should be with open protocol like Modbus /Bacnet for integrating with BAS. grooved couplings for condenser and cooler water in/out connections, sight glass, Liquid Line Isolation Valve,complete charge of refrigerant and oil, accessories as required and called for, automatic and safety controls mounted in central Advanced Microprocessor based control panel with automatic controls, coloured & graphical display, complete with accessories and BMS compatible BACNET/MODBUS Protocol with BMS cards, all mounted on a steel frame complete as per specifications. Motor shall be suitable for 415±10% 50 cycles. 3 phase AC supply and motor cable terminal box shall be suitable to connect Aluminium Cabling. Refrigerant used shall be Ozone friendly HFC-134a as detailed in specifications. Chiller shall be provided with electrical terminal box. Chiller shall be Witness factory tested with VFD at AHRI conditions at 100%, 75%, 50% and 25% load to establish COP with hvac consultant / client. Compressors must be of OEM'S own Make only.

Motor shall be suitable for 415±10% 50 cycles. 3 phase AC supply . Refrigerant used shall be Ozone friendly HFC (R134a) or HCFC as per specification.

Unit mounted VFD to ensure that starting current shall not exceed twice the full load current. Chiler shall be suitable for variable Secondary pumping system CHILLER Chiller Water IN. ; 54°F Chiller Water OUT. ; 44°F Maximum IPLV at AHRI : 0.38 IKW/TR Cond Water IN. ; 89°F Cond Water OUT. ; 96°F Evaporator fouling factor : 0.0001 F.F(h.ft2.°F/Btu) Condenser fouling factor : 0.00025 F.F(h.ft2.°F/Btu) 160 TR WATER COOLED SCREW CHILLER WITH VFD

Primary Chilled water pumps

Supply, Installation, Testing and Commissioning of end suction type centrifugal pump sets factory assembled and tested for rated efficiency complete with IE-04, TEFC squirrel cage induction motor with class 'F' insulation, epoxy painted common base frame, flexible coupling, coupling guard, mechanical seals, vibration isolation arrangement etc. for recirculation of chilled water for the central air conditioning system as per the specifications. The pumps shall be suitable for operation on 415±10% Volts, 50 Hz, 3 Phase AC power supply. Quoted price shall be inclusive of inertia base with spring isolators for each pump. Pumps shall be insulated as per the specifications. The pump characteristics shall be as follows:

Chilled water flow rate : 350USGPM Head : 15 M Maximum Permissible Speed : 1450 RPM End suction pumps(3W+1S)

Secondary Chilled water pumps

Supply, Installation, Testing and Commissioning of end suction type centrifugal pump sets factory assembled and tested for rated efficiency complete with IE-04, TEFC squirrel cage induction motor with class 'F' insulation, epoxy painted common base frame, flexible coupling, coupling guard, mechanical seals, vibration isolation arrangement etc. for recirculation of chilled water for the central air conditioning system as per the specifications. The pumps shall be suitable for operation on 415±10% Volts, 50 Hz, 3 Phase AC power supply. Quoted price shall be inclusive of inertia base with spring isolators for each pump. Pumps shall be insulated as per the specifications. The pump characteristics shall be as follows:

Chilled water flow rate : 500 USGPM Head : 35mtr Maximum Permissible Speed : 1450 RPM End suction pumps (3W+1S)

Condenser Water pump

Supply, Installation, Testing and Commissioning of end suction type centrifugal pump sets factory assembled and tested for rated efficiency complete with IE-04, TEFC squirrel cage induction motor with class 'F' insulation, epoxy painted common base frame, flexible coupling, coupling guard, mechanical seals, vibration isolation arrangement etc. for recirculation of chilled water for the central air conditioning system as per the specifications. The pumps shall be suitable for operation on 415±10% Volts, 50 Hz, 3 Phase AC power supply. Quoted price shall be inclusive of inertia base with spring isolators for each pump. Pumps shall be insulated as per the specifications. The pump characteristics shall be as follows:

Condenser water flow rate :665 USGPM Head :35mtr Maximum Permissible Speed : 1450 RPM End suction pumps (3W+1S)

Variable Speed Pump

Supply, Installation, Testing and Commissioning of variable speed pumping system comprising of following accessories and as per the specifications. The system shall be complete in all respects including electrical components suitable for pump motor. Each pump shall have variable frequency drive. The entire system alongwith secondary CHW pumps shall be supplied through single vendor.

For Chilled Water Variable frequency drive (VFD) : 3 Nos. Dedicated micro processor based pump controller : 1 No. Differential pressure sensors/ transmitters : 2 Nos. Software duly down loaded in pump controller : 1 Set VSPS shall be BMS compatible and interfacing amongst all components and compatibility of I/O signals shall be provided : 1 Set Variable Speed Pumping System as described above.

COOLING TOWER

Supply, Installation, testing and commissioning of Induced Draught Counter Flow type Cooling Towers . The Cooling Tower shall be complete with FRP Casing, FRP Basin, unpressurised, Gravity Flow – Header and branch arm system. 0.2 mm thick PVC Film Fills, High Efficiency Drift Eliminators, M.S.H.D.G. Ladder and direct driven Axial Flow Propeller Type Fan & Totally Enclosed Weather Proof (IP-55), High Efficiency Motor, suitable for 415±10% volts, 50 cycles, 3 phase power supply and related accessories.

a. Max. wet bulb temperature : 83 F (28.3 C) b. Temperature of water entering cooling tower : 96.8 F (36.0 C) c. Temperature of water leaving cooling tower : 89.6 F (32.0 C) d. Water flow rate : 665 USGPM 200TR Rating

CHILLED WATER BASED CASSETTE/ HI-WALL UNITS

Supply, Installation, Testing and Commissioning of chilled water based cassette type indoor units suitable for two pipe system. These units shall consist of a fan section with dynamically balanced centrifugal fan/s driven by FHP/TEFC squirrel cage induction motor, multirows deep coil of copper tubes and aluminium fins etc. Enclosures shall be fabricated as specified for Dx split units. These units shall be equipped with synthetic fibre filters, insulated drain pan, safety controls, thermostat, a set of valve station with pair of ball valves (one with strainer and one without strainer) and self balancing pressure independent flow control valves etc. all complete in a unit. The unit shall be provided with BMS compatible Kit.

a. 4 TR nominal capacity Cassette type unit (chilled water based) with cordless control.

b. 3.5 TR nominal capacity Cassette type unit (chilled water based) with cordless control. (Rate only item)

d. 3.0 TR nominal capacity Cassette type unit (chilled water based) with cordless control.

e. 2.5 TR nominal capacity Cassette type unit (chilled water based) with cordless control.

f. 2.0 TR nominal capacity Cassette type unit (chilled water based) with cordless control.

g. 1.5 TR nominal capacity Cassette type unit (chilled water based) with cordless control.

h. 1.0 TR nominal capacity Cassette type unit(chilled water based) with cordless control.

i. 2.0 TR nominal capacity Hi-wall split type unit (chilled water based) with cordless control.

j. 1.5 TR nominal capacity Hi-Wall Split type unit (chilled water based) with cordless control.

AIR HANDLING UNITS

Supply, Installation, Testing & Commissioning of DOUBLE SKIN type Ceiling/Floor Mounted (Vertical / Horizontal) type AHU's

Comprising of Following : Frame Structure : Extruded profile Aluminum Anodized with thermal break Panels : Double Skin 43±2 mm Thick Mineral wool Insulation shall be injected with minimum 40±2 Kg./M³ density. Pencil coving should be given on the inner frame of AHU's. AHU frame work shall be Anodized Aluminum Section minimum 2 mm thick with thermal break profile & internal coving. Inner Skin : 0.8 mm G.I Plain Galvanized Sheet steel Outlet Skin : 0.8 mm G.I Pre-plasticized / Powder coated Galvanized Sheet steel Drain Pan : 1.2mm Thk SS304 - with 19mm Thk Nitrile Rubber insulation along with 40NB threaded Nipple in SS Construction. 3 way slope to avoid water accumulation in side tray, In case of Coils in two parts the Drain Pan to be made also in two parts ( Upper & lower) with flexible pipe in between them. Sealing Gasket : Food Grade / D profile gaskets of approved MOC Fan Type : Plug Type - Fan shall be as per AMCA standard.

Along with plug type fan having Static Pressure suitable for VFD drive, Access Doors on both sides, view glass & limit switch, Inspection window with transparent panels on both sides interlocking of Access doors (Doors should not open while fan is ON). Along with Suitable in AHU for tapping for switches, controllers & control wiring, all internal wiring, Fresh air intake with filter, marine light in all sections etc. The entire AHU assembly will be mounted on a common skid fabricated out of HDG MS channel, All nut bolts, sheet metal screws, fasteners will be Zinc / Nickel plated having resistance against rusting complete Rubber Block type isolators below fan structure required to avoid vibration & direct contact of fan with AHU structure. Motor : Standard foot mounted Crompton / BBL / ABB make high efficiency IE-03 Motor with variable frequency drives of suitable capacity. Motor shall compactable with VFD, drive packages.

All panels with more than one outgoing starter feeder shall All internal wiring and copper earthing of air handling unit motors from the panel shall be included. Wiring and earthing terminating into MCCB in each panel shall be provided by the electrical contractor.

6800 CFM / 17 TR - 50mm Static Pressure (CS-AHU)

7600 CFM / 19 TR - 50mm Static Pressure (CS-AHU)

12800 CFM / 32 TR - 50mm Static Pressure (FM-AHU)

13000 CFM / 32.5 TR - 50mm Static Pressure (FM-AHU)

13200 CFM / 33 TR - 50mm Static Pressure (FM-AHU)

13400 CFM / 33.5 TR - 55mm Static Pressure (FM-AHU)

TREATED FRESH AIR UNITS

Supply, Installation, Testing & Commissioning of DOUBLE SKIN type Ceiling suspended type TFA's Comprising of Following : Frame Structure : Extruded profile Aluminum Anodized with thermal break Panels : Double Skin 43±2 mm Thick Mineral wool Insulation shall be injected with minimum 40±2 Kg./M³ density. Pencil coving should be given on the inner frame of AHU's. AHU frame work shall be Anodized Aluminum Section minimum 2 mm thick with thermal break profile & internal coving. Inner Skin : 0.8 mm G.I Plain Galvanized Sheet steel Outlet Skin : 0.8 mm G.I Pre-plasticized / Powder coated Galvanized Sheet steel Skid : MS Epoxy Coated Drain Pan : 1.2mm Thk SS304 - with 19mm Thk Nitrile Rubber insulation along with 40NB threaded Nipple in SS Construction. 3 way slope to avoid water accumulation in side tray, In case of Coils in two parts the Drain Pan to be made also in two parts ( Upper & lower) with flexible pipe in between them. Sealing Gasket : Food Grade / D profile gaskets of approved MOC Fan Type : Plug Type - Fan shall be as per AMCA standard.

Along with plug type fan having Static Pressure suitable for VFD drive, Access Doors on both sides, view glass & limit switch, Inspection window with transparent panels on both sides interlocking of Access doors (Doors should not open while fan is ON).Along with Suitable in AHU for tapping for switches, controllers & control wiring, all internal wiring, Fresh air intake with filter, marine light in all sections etc. The entire AHU assembly will be mounted on a common skid fabricated out of HDG MS channel, All nut bolts, sheet metal screws, fasteners will be Zinc / Nickel plated having resistance against rusting complete Rubber Block type isolators below fan structure required to avoid vibration & direct contact of fan with AHU structure. Motor : Standard foot mounted Crompton / BBL / ABB make high efficiency IE-03 Motor with variable frequency drives of suitable capacity. Motor shall compactable with VFD, drive packages.

All panels with more than one outgoing starter feeder shall be provided with separate MCCB/MCB for incoming & outgoing. All internal wiring and copper earthing of air handling unit motors from the panel shall be included. Wiring and earthing terminating into MCCB in each panel shall be provided by the electrical contractor.

3900 CFM / 9.75 TR - 50mm Static Pressure (FM-AHU cum TFA) for (GROUND+FIRST FLOOR)

2200 CFM / 5.5 TR - 40mm Static Pressure (FM-AHU cum TFA) for (SECOND+ THIRD FLOOR)

2900 CFM / 7.25 TR - 40mm Static Pressure (FM-AHU cum TFA) for (FOURTH +FIFTH FLOOR)

3800CFM / 9.5 TR - 40mm Static Pressure (FM-AHU cum TFA) for (SIXTH+SEVEN+EIGHT FLOOR)

LOW SIDE WORK

CHILLED /HOT WATER PIPING

Supplying, laying/ fixing, testing and commissioning of following Chilled water pipe of following size of MS Class C along with necessary clamps, vibration isolators and fittings & adequately supported on rigid supports duly painted/buried in ground excavation & refilling etc as per specification & as required complete in all respects. Note : The Pipes of sizes 150mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 8 mm thick MS sheet for pipes of 400 mm dia and above.

300 mm dia MS Pipes

250 mm dia MS Pipes

200 mm dia MS Pipes

150 mm dia MS Pipes

125 mm dia MS Pipes

100 mm dia MS Pipes

80 mm dia MS Pipes

65 mm dia MS Pipes

50 mm dia MS Pipes

40 mm dia MS Pipes

32 mm dia MS Pipes

25 mm dia MS Pipes

INUSLATED VALVES

Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled/hot water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/hot water circulation as specified

250 mm dia

200 mm dia

150 mm dia

125 mm dia

100 mm dia

80 mm dia

65 mm dia

50 mm dia

40 mm dia

BALANCING VALVE WITH BUILT IN MEASURING FACILITY with C I body flanged construction with EPDM coated disc with long pitch with protected out pipe insulation & PN 16 pressure rating for chilled / hot water circulation as specified.

250 mm dia

200 mm dia

NON - RETURN VALVE with dual plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating for chilled / hot water circulation including insulation as specified.

150 mm dia

125 mm dia

Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified.

150 mm dia

125 mm dia

80 mm dia

65 mm dia

50 mm dia

40 mm dia

HIGH RANGABILITY/PID (PRESSURE INDEPENDENT CONTROL & BALANCING VALVE)

Supply installation, testing & commissioning of Two Way high rangaeability/ pressure independent dynamic balancing cum control valve fitted with motorized, modulating actuators with linear stroke of minimum 15mm, in chilled water lines at each air handling unit, the actuator shall have shut off capability of minimum 4 Bar rating. the actuator shall be controlled by building automation system & should accept a signal of 4-20mA/2-10 VDC. The valve shall be suitable for following flow rates & conforming to specification. The digital electronic controller with LCD display capable of accepting 0-10V DC signal from BMS & Water Temperature signals from the coil inlet & outlet sensors conforming to detailed specifications. all other accessories i.e Sensors-3 No. 230V/24VAC power Supply 1 No. thermowell-1 No. should be included in thsi item.

65 mm dia Modulating type

50 mm dia Modulating tupe

40 mm dia Modulating type

32 mm dia CWC Valves ON/OFF

25 mm dia CWC Valves ON/OFF Type

Supply,Installation Testing and Commissioning of the following Ball Valves with Strainer duly insulated as per specifications and drawings. It shall be brass forged body construction with chrome plated brass ball and handle of stainless steel constructions.

32 mm dia

25 mm dia

20 mm dia

Supply,Installation Testing and Commissioning of the following Ball Valves without strainer duly insulated as per specifications and drawings. It shall be brass forged body construction with chrome plated brass ball and handle of stainless steel constructions.

32 mm dia

25 mm dia

20 mm dia

Supply, installation, testing and commissioning of the following Drain (Ball) Valves (full way) of brass construction with PTFE seat, screwed female ends duly insulated as per specifications and drawings.

25 mm dia

20 mm dia

Supply, installation, testing and commissioning of Auto Purge Valves of brass construction with screwed ends duly insulated as per specifications and drawings complete in all respect.

25 mm dia

20 mm dia

Supply,Installation Testing and Commissioning of Flexible Pipe Connection (Double Arch PN 16 rating) at pumps suction and discharge (Material of Construction-EPDM Rubber ) with integral rubber flanges with SRR & control unit suitable for operation between Temperature rage: - 10 to 90 degree celcius.

250mm dia

200 mm dia

150 mm dia

125 mm dia

Providing and fixing in position the industrial type pressure gauges with gun metal/brass valves complete as required.

Providing & fixing in position the mercury in glass industrial type thermometer complete as required.

AIR DISTRIBUTION

AIR DISTRIBUTION (FOR AIR CONDITIONING AREAS) Supply, installation, balancing and commissioning of factory fabricated/Site Febricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. (It shall be as per SMACNA standards)

24G Galvanized Sheet Steel Ducting

22G Galvanized Sheet Steel Ducting

AIR DISTRIBUTION (FOR TFA) Supply, installation, balancing and commissioning fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.

24G Galvanized Sheet Steel Ducting

Supply, installation, testing and commissioning of GI volume control duct damper (18 gauge) complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

Supply, fabrication, installation and testing the flexible Canvas constructed of fire resistant double resin sleeve as per the approved shop drawings.

SUPPLY / RETURN AIR DIFFUSERS

Supplying, fixing, testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core.

SUPPLY / RETURN AIR GRILLES

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium return air grill with louvers but without volume control dampers complete as required.

FIRE DAMPERS

Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring, the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications.

Fire damper

Actuator

INSULATION

Supply and Application of 38mm/32mm/25mm/19mm thick closed cell elastomeric insulation in tubing form/ flat sections for chilled water piping to be installed throughout the project as per the specifications.

Quoted price shall be inclusive of adhesive and UV/ Mechanical Protection using weather resistant paint & Glass Cloth/CSM as per specifications.

300mm dia (38mm thick)

250mm dia (32mm thick)

200mm dia (32mm thick)

150mm dia (32mm thick)

125mm dia (32mm thick)

100mm dia (32mm thick)

80mm dia (25mm thick)

65mm dia (25mm thick)

50mm dia (25mm thick)

40mm dia (25mm thick)

32mm dia (25mm thick)

25mm dia (25mm thick)

Supply and Application of 26 Gauge Aluminium cladding for chilled water piping to be installed in plant room as per the specifications.

300mm dia (38mm thick)

250mm dia (32mm thick)

200mm dia (32mm thick)

150mm dia (32mm thick)

125mm dia (32mm thick)

100mm dia (32mm thick)

80mm dia (25mm thick)

65mm dia (25mm thick)

50mm dia (25mm thick)

40mm dia (25mm thick)

32mm dia (25mm thick)

25mm dia (25mm thick)

DUCT INSULATION

Supplying and fixing of external thermal insulation on ducts with Cross Linked Closed Cell Polyethylene FR-XPE, Class O fire rating insulation, tape & adhesive as required of following thickness.

a. 13 mm thick Aluminium Metalized Insulation

Acoustic Lining of Duct

Supply, installation & testing of nitrile rubber/sound absorbing sheet (Density 140-180 kg/m³ ) in AC supply air ducts , as per specifications.

10 mm thick

Supply and Application of 6 mm thick closed cell elastomeric insulation in tubing form for condensate drain piping as per the specifications.

c. 32mm dia

d. 25mm dia

e. 20mm dia

INLINE FANS(TOILET)

Supply, Installation, Testing and Commissioning of circular/rectangular inline fans for exhaust air as shown on drawings, complete with sheet metal casing, direct driven centrifugal fan, motor with proper protection and inspection door,gravity louvers etc. as per the specifications. Fan should be suitable for operation on 415+10% volts, 50 Hz, three phase or 220±6 %, 50 Hz, single phase AC power supply as required. Single Phase inline fans shall be provided with speed regulators.The unit shall be provided with BMS compatible Kit.

Fan shall be suitable for installation or as shown on drawings and shall be of following capacities:

600 CFM - 25 MMWG Static Pressure

PROPELLER FANS(PANTRY)

a. 450 mm dia 900/1400 RPM fan suitable for 220+6%Volts, 50 Hz, single phase AC supply.

AXIAL FLOW FANS (STAIRCASE PRESSURISATION)

Emergency Supply:

Supply, Installation, Testing & Commisioning of AMCA Certified (For Air and Sound Performance) tube axial flow fans of different capacities in standard GI/M.S. contruction as mentioned below. Entire fan model and AMCA Seal shall apear in techncial submittal of fan. All the fans shall be synthetic enamel painted/ hot dip galvanized with minimum 220 GSM Zinc Coating and complete with bird screen at fan inlet. The electric motor coupler shall be IE-03 squirrel cage induction type conforming to IS-325, IP-55 rated with class `F' insulation. Fan efficiency should not be less than 65%, and noise level should not be more than 85 db @ 3 m distance when measured under hemisperical reverberant room conditions. Quoted price shall be inclusive of all accessories like bird screens, vibration isolators,mounting brackets/feet/ duly enamel painted M.S structure etc. Fans mentioned as outdoor type shall be good for outdoor installation with proper cowl and mounting arrangement as per approved shop drawings. Fans shall be as per specifications and design drawings. Fans shall be as per specifications and design drawings.The Unit shall be complete with all internal cabling/wiring along with suitable rating starter, earthing from motor upto the cable termination box. Axial Flow Fans shall follow the design parameters as mentioned below:

14000 CFM - 50 MMWG STATIC PRESSURE

AXIAL FLOW FANS (LIFT PRESSURISATION)

Emergency Supply:

Supply, Installation, Testing & Commisioning of AMCA Certified (For Air and Sound Performance) tube axial flow fans of different capacities in standard GI/M.S. contruction as mentioned below. Entire fan model and AMCA Seal shall apear in techncial submittal of fan. All the fans shall be synthetic enamel painted/ hot dip galvanized with minimum 220 GSM Zinc Coating and complete with bird screen at fan inlet. The electric motor coupler shall be IE-03 squirrel cage induction type conforming to IS-325, IP-55 rated with class `F' insulation. Fan efficiency should not be less than 65%, and noise level should not be more than 85 db @ 3 m distance when measured under hemisperical reverberant room conditions. Quoted price shall be inclusive of all accessories like bird screens, vibration isolators,mounting brackets/feet/ duly enamel painted M.S structure etc. Fans mentioned as outdoor type shall be good for outdoor installation with proper cowl and mounting arrangement as per approved shop drawings. Fans shall be as per specifications and design drawings. Fans shall be as per specifications and design drawings.The Unit shall be complete with all internal cabling/wiring along with suitable rating starter, earthing from motor upto the cable termination box. Axial Flow Fans shall follow the design parameters as mentioned below:

8000 CFM - 50 MMWG STATIC PRESSURE

ELECTRICAL INSTALLATION

MOTOR CONTROL CENTRE

Supply, Installation, Testing and Commissioning of floor mounted cubicle type electrical panel duly powder coated complete with aluminium bus bars, incoming, out going feeders etc. as per specifications, drawings attached in RFP and as described below. The panel shall incorporate an extract fan mounted at the top of the panel complete with thermostat suitable to run the fan at 50 deg C. Fault level 36 kA/1 Sec.

Panel suitable for below equipment rating CHILLERS PUMPS COOLING TOWER PRESSURIZATION UNITS MCC as described above.

Description of Work / Item(s)

Amount

Supply , Installation , Testing and Commissioning of Acrylic Firestop Sealant Hilti CP 606 or equivalent in gaps around non-combustible penetrants like ducts or metal pipes passing Through Penetration on Floor / wall for mechanical services for annular gaps up to 50 mm to provide minimum 2 hours fire rating when subject to the test conditions of UL 1479/ASTME 814 standards as per detailed specifications given in RFP .(13 mm thickness of sealant)

Supply , Installation , Testing and Commissioning of high performance intumescent firestop sealant Hilti FS One max or equivalent make for Floor / wall through penetration for mechanical services around combustible penetrations upto 2 inches like plastic pipes or ducts/pipes with insulation passing through floor to provide minimum 2 hours fire rating when subject to test standards of UL 1479/ASTM-E 814 as per detailed specifications enclosed .

Supply , Installation , Testing and Commissioning of intumescent flexible firestop wrap strip Hilti CP 648 E or equivalent make for Floor / wall through penetration for mechanical services like for plastic pipe, insulated pipe and various non-metallic penetrations from 2" to 6" diameter passing through floor slab to provide minimum 2 hours fire rating when subject to test standards of UL 1479/ASTM-E 814 as per detailed specifications given in RFP . the work should be executed considering wraps on both sides of wall

Plastic Pipe diameter of 2.5'' (CP 648-E Firestop Wrap), Min. recommended hole dia. in floor: 92 mm

Plastic Pipe diameter of 3'' (CP 648-E Firestop Wrap), Min. recommended hole dia. in floor: 112 mm

Plastic Pipe diameter of 4'' (CP 648-E Firestop Wrap), Min. recommended hole dia. in floor: 132 mm

Plastic Pipe diameter of 5'' (CP 648-E Firestop Wrap), Min. recommended hole dia. in floor: 152 mm

Plastic Pipe diameter of 6'' (CP 648-E Firestop Wrap), Min. recommended hole dia. in floor: 202 mm

Supply , Installation , Testing and Commissioning of ready-to-use firestop collar Hilti CP 644, or equivalent make for Floor / wall through penetration for mechanical services made of a galvanized steel housing and intumescent inserts for firestopping large combustible pipes with diameters from 7" (177 mm) up to 10" (250 mm) passing through floor slab to provide minimum 2 hours fire rating when subject to test standards of UL 1479/ASTM-E 814 as per detailed specifications given in RFP . The work should be executed conidering collars on both sides of wall as follows:

Plastic Pipe diameter of 7'' (CP 644 Firestop Collar)

Plastic Pipe diameter of 8'' (CP 644 Firestop Collar)

Plastic Pipe diameter of 9'' (CP 644 Firestop Collar)

Plastic Pipe diameter of 10'' (CP 644 Firestop Collar)

Supply , Installation , Testing and Commissioning of Fire stop mortar system Hilti CP 636 or equivalent make Through Penetration on (Medium to large size i.e. > 4" gaps) For through penetration for wall / floor mechanical and electrical services , with minimum 2 hours fire rating when tested in accordance with UL 1479/ASTM-E 814 standards, for horizontal openings in floors or slabs after passing service lines like cables/cable bundles, cable trays etc. as per detailed specifications given in RFP . The material should be applied considering 65 mm thk mortar with 0% occupancy.

Supply , Installation , Testing and Commissioning of rodent and termite proof Fire Barriers Hilti CFS COS ( Composite Sheet) system or equivalent make for 2 hours fire rating when tested in accordance with ASTM E 814/UL 1479 standards - Under Panel Sealing (Medium to large size i.e. > 4" gaps) For through penetration for wall / floor mechanical and electrical services The Composite Sheet 3.81 mm thick, bonded with organic/inorganic fire-resistive elastomeric #SS 304 (Stainless steel) sheet. One side it should be bonded with 26 gauge #SS 304 (Stainless steel) sheet and the other side it should be reinforced with hexagonal shaped #SS 304 (Stainless steel) wire mesh and covered with aluminium foil for the penetrants and the big opening as per detailed specifications given in RFP .

Supply , Installation , Testing and Commissioning expanding firestop foam Hilti CP 620 or Equivalent make , with minimum 2 hours fire rating when tested in accordance with UL 1479/ASTM-E 814, for through Penetration on wall / Floor for sealing inaccessible, complicated or annular gaps openings for horizontal openings in floors or slabs made of concrete/ masonry or Gypsum after passing service lines like cable trays or cables/cable bundles as per detailed specifications given in RFP .

Supply , Installation , Testing and Commissioning of Firestop Factory-assembled cable device Hilti Speed Sleeve (CP 653 BA) or Equivalent make for Communication Cables Sealing with repenetrating facility for floor / wall , containing an intumescent material and a flexible cloth which limits the warm and cold smoke propagation to less than 1 CFM per device for passing cables through floor slab to provide minimum 2 hours fire rating when subject to test standards of UL 1479/ASTM-E 814. No additional material shall be required for adding or re-moving cables after the first installation as per detailed specifications given in RFP ..(Note: for server rooms and data centers and areas where frequent maintenance is required as directed by engineer in-charge. )

CP 653BA (2" Size)

CP 653 BA (4" Size)

Supply , Installation , Testing and Commissioning of Acrylic Firestop Sealant Hilti CP 606 or Equivalent make in gaps between wall and slab made of concrete/masonry/gypsum on both sides of wall to provide minimum 2 hours fire rating when subject to the test conditions of UL 2079 & ASTM E 1966 standards with Min. movement capability of +_12.5%. as per detailed specifications given in RFP .( measurements will be based Consideting 25mm joint width and 1 R Mtr length with 13mm thickness on both sides of wall )

Supply , Installation , Testing and Commissioning of sprayable Fire-rated joint spray Hilti CFS SP WB or Equivalent make in gaps between vertical concrete/masonry wall and deck slab to provide minimum 2 hours of fire rating when tested as per UL 2079 standard as per detailed specifications given in RFP . (measurements will be made on R mtr Considering 100mm joint width & 3 mm WFT, wet film thickness )

Supply , Installation , Testing and Commissioning of silicone based firestop Sealant Hilti CP 601S or Equivalent make in horizontal & vertical movement or expansion joints to provide minimum 2 hours fire rating along with movement capability of +_25% when subject to the test conditions of UL 2079 standards as per detailed specifications given in RFP .(Measuremet will be made on R mtr Considering 50 mm joint width and 13mm thickness on both sides of wall)

Supply , Installation , Testing and Commissioning of intumescent based coating Hilti CP 678 or Equivalent make on internal cables/bunch cables & cable tray for at least 1 mtr in every 14 Mtrs for horizontal runs and to entire length of vertical runs . The coating shall have a density in the range of 1.2 to 1.4 Kg/ L. The coating shall be non-toxic, asbestos and halogen free and shall have good mechanical strength as per detailed specifications given in RFP . . (measurement will be made by R mtr x Diameter of cable in Mtr giving area in Sq mtr )

Supply , Installation , Testing and Commissioning of ablative coating Hilti CP 679A or Equivalent make on external cable/ bunched cables in enclosed and semi-enclosed cable runs to be coated at least 1 mtr in every 14 mtrs of cable runs for the horizontal runs and to entire length of the vertical run as per IEC 60332 part.3 tested by DNV' interpretation of SOLAS 1974 as per detailed specifications given in RFP . (measurement will be made by R mtr x Diameter of cable in Mtr giving area in Sq mtr )

Supply , Installation , Testing and Commissioning of All cables penetrations of fire-rated walls or floors shall be sealed with a Hilti CFS CTS (multi-cable transit block) or Equivalent make system for use in multi-cable transit frames. The multi-cable transit system should cover all cable diameters from 4 core 6 Sq mm to 400 Sq mm , #.5 core with a module adapter system where no peeling of single layers is necessary as per detailed specifications given in RFP . (only for high tension cable wires )

Description of Work / Item(s)

Amount

SEWAGE TREATMENT PLANT, Capacity : 70 KLD.

Note : The Tender for this work is on the basis of Lump Sum Turnkey basis. Contractor must include all items that are necessary and essential to provide a complete working plant to the satisfaction of Engineer in charge. The BOQ given hereafter is only for the purpose assessing the overall costing of the Project and will be used for arriving at the payment schedule to the contractor. The complete operation of the Sewage treatment plan is Automatic.All pumps and blowers are auto in operation., excepts valves which are manual.

Preliminary Works

Shop Drawings.

Detailed GA drawing, flow diagram, equipment list, power load requirement

Design, calculations of all elements of the plant, electrical and mechanical work to satisfy adequacy of design

Submission of detailed GOOD FOR CONSTRUCTION' stage architectural, structural, construction, electrical, mechanical and piping drawing for approval.

Sewage Treatment Plant

Design, Supplying, Installing, Testing & Commissioning of Sewage Treatment Plant capacity 70 KLD. The plant proposed shall be 70 kld with a main pump room. The plant is proposed to be installed in the Basement along with the pump room for better maintenance. Adequete opening shall be provided for this purpose, following shall be considered as basis for the plant design:

Nature of effluent - Domestic Sewage from Toilet use and kitchen waste water. Anticipated effluent parameters before treatment: PH 7.5 - 8.5 BOD 250-400 mg/lt SS 200-450 mg/lt. COD 600-800 mg/lt. Oil & Grease upto 50 mg/lt

Desired Sewage discharge standard after ACF are as below: PH 6.5 – 8.5 BOD5 Less than 20 Mg/L S. Solids Less than 40 Mg/L COD Less than 50 Mg/L Oil & Grease Less than 5 Mg/L Ecoli < 103 MPN Nitrogen - 50 Mg/L

Desired Sewage discharge standard after UF are as below: PH 6.5 – 8.5 BOD5 Less than 5 Mg/L S. Solids Nil COD Less than 40 Mg/L Oil & Grease Nil Ecoli Absent Nitrogen - Less than 10 Mg/L

Sewage treatment plant shall include the following items: Bar Screen Chamber Sewage equalization tank/sump(In Civil clinets scope) MBBR Tanks(In Civil clinets scope) Settling/ Clarifier Tank(In Civil clinets scope) Clear Water tank(In Civil clinets scope) Softener Feed PUMPS (if required) Recycled / Soft Water tank(if required) Sludge Holding Tank(In Civil clinets scope) Plant Room Sump Filtration through MGF & ACF Ultrafiltration plant Air Blowers, Pumps & equipment Piping, valves etc Electrical Panel & Cabling Common plant room adjacent to STP. All piping, valves & level indicator/controller etc. within plant room.

Supply, installation, testing & commissioning of 2 Nos Stainless Steel Perforated Screen with suitable lifting arrangement (size 600 mm wide x 1200 mm high approx)

Supply, installation, testing & commissioning of electronic type level indicator and controller for automatic operation of the system with high/low level alarm complete with auxiliary NO/NC contacts.

Contractor/Vendor shall ensure submission of detailed GA drawings (Plan & Section), P & I diagram, schematic diagram for the above mentioned components and additional components such as inserts, puddle flanges, vent pipes etc. if so required for the complete work.

Supply, installation, testing & commissioning of non clogging type pumps, having C.I. casing & bronze impeller complete with all accessories, motor of required capacity. Delivery header with isolation valve, pressure gauge on delivery line with isolation cock level controller with wiring to control the level of sump automatically. Pump shall have following duty.

Self Primimg Transfer Pumps (2 Nos. - One working & one standby) (Solid handling Cap. 40 mm) Flow rate (each) = as required Head = 10-12 Mtr

Plant room sump pump 2 Nos (1 working + 1 standby). Flow rate = as required Head = 10-12 Mtr (Solid handling size for this pump shall be 20 mm).

Mono block (Self Primimg)centrifugal Sludge Recirculation Pumps (2 Nos. - One working & one stand by) (Solid handling cap. 20 mm) Flow rate (each) = as required Head = 8-10 Mtr

Cost shall be inclusive of PVC flexible Hose pipe ( for piping submerged in effluent) with M S epoxy piping (for piping non-submerged in effluent)

Provision of guide ropes to guide submersible pump from upper level to operational level in sump basin with channels / angle section of MSEP shall be made by the STP contractor.

Supply, Installation, testing & commissioning of Air diffuser system with 2 nos. twin lobe -type air blower of capacity as required at the pressure of 0.5 kg/cm driven through “V” belt or directly coupled through flexible coupling to TEFC motor of suitable HP for 415 + 10 volt ,3phase,50cycle AC supply including fine and Coarse bubble membrane type diffusers complete with valves & air distribution grid, flexible pipie etc. complete as required.(1 working+ 1 standby)

Air piping shall comprise of pipes droppers/ laterals with M S Class "B" (epoxy coated)/CPVC (Under water)Header complete with all fittings such as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps, puddle flanges etc cutting chases & making good.

Aeration system shall be provided for Equalization Tank, and Reactor Tank.

Providing and fixing all piping (as described below) and isolation control valves for making the system complete. SS 316L :Submerged air piping MS Epoxy : Air piping/ CPVC (For Under Water) PVC piping :Pumped effluent & tank overflow pipe line

Supply, installation, testing and commissioning of Media for Aeration Tank (As Required)

Supply, installation, testing and commissioning of Tube Pac Media for Sludge Settling Tank

Supply, installation, testing and commissioning of Hydraulic operated Filter Press of 18 Plates of size; 24"x24", with sludge tray and Filter Press Feed Screw Type Pumpset of capacity 4.5 m3/hr 2 Nos. (1W + 1S) with interconnecting piping and air line connection complete.

Supplying, installing, testing & commissioning of centrifugal vertical inline filter feed water pumps SS-304 casing, S.S 304 impeller and SS-304 shaft, C.I. Base CED coating & head TEFC motor (with mechanical seal). Pressure gauge with isolation cock, NRV, Isolation valve on delivery line. Isolation valve, strainer at suction. The pump shall be suitable for 415 ± 10% volts, 3 phase, 50 cycles a/c supply. Capacity :as required Head : 30 M No. of Pumps (1 working + 1 standby)

Supplying, installing, testing and commissioning of MS vessel filter(5mm thikness) with frontal piping and associated valves and accessories. Filter shall be suitable for a minimum working pressure of 6.0 kg / cm2 and shall include media, standard fittings like pressure tight manholes, initial charge of media, raw water distributor, under drain system, face piping, pressure gauges etc.,

The Multi-grade filter shall be constructed of FRP material with inner shell of integrated polyethylene, polypropylene and other material as per manufacturer's standard.The inter distribution system and the underbed draw off system shall be of Hub & Lateral type of polypropylene material. The filter shall be provide with manhole cover, hand hole, flanged outlet for piping/valve connection and adequate tripod with skid self supporting structure for making the installation completed. The filter shall also be provided with vacuums breaking connection / accessories to avoid any collapse of internal lining. All filters shall be provided with lifting lugs and making the installation completed as required. Capacity - as required Filtration rate (approx) - as required Filter dia (approx.) - as required Working pressure - 4.0 Kg/Sq.cm Test pressure - 7.0 Kg/Sq.cm

The Activated Carbon filter shall be constructed of FRP material with inner shell of integrated polyethylene, polypropylene and other material as per manufacturer's standard.The inter distribution system and the underbed draw off system shall be of Hub & Lateral type of polypropylene material. The filter shall be provide with manhole cover, hand hole, flanged outlet for piping/valve connection and adequate tripod with skid self supporting structure for making the installation completed. The filter shall also be provided with vacuums breaking connection / accessories to avoid any collapse of internal lining. All filters shall be provided with lifting lugs and making the installation completed as required.

Capacity - as required Filtration rate (approx) - as required Filter dia (approx.) - as required Working pressure - 4.0 Kg/Sq.cm Test pressure - 7.0 Kg/Sq.cm

Ultra filtration (UF) System

No of Pumps – 2 (1 working + 1 stand by) Type of Pumps – Vertical inline multistage Feed Flow rate of pumps – about 4.5 cum/hr Head – 20 meters (2.0 bars) MOC – CI with SS internals Bag filter or Cartridge filter – 1 set MOC of housing – PP Type of Bag / Cartridge - PP 5 micron Feed flow rate – about 12.5 cum/hr Product flow rate – about 4.25 cum/hr Recovery – around 90% No of UF membrane – 2 nos (Outside In) Type of UF membrane – Hollow fibre Piping within the unit – UPVC / CPVC with the valves, solenoid valves for automation Control Panel – MS powder coated CIP system – HDPE tank @ 750 liters with electronic dosing pump (1 set) CIP skid - MSEP with necessary connection and accessories Air Scouring – Tourbo Air Blower – 1 HP approx MOC of Blower – MSEP / CI Backwash pumps - 10cum/hr (1w+1s)

Instrumentation

Supply installation of Electromagnetic flow metre at Inlet and Outlet of STP

Supply installation of Ph at Outlet of STP

Electrical Installation

Motor Control Centre

Incoming

Spare MCB’s of following capacities: 32 amps TPN MCB’s 6Nos. Necessary cable alleys, internal / cabling, wiring, cabling from MCC to various pumps / equipment and interlocking, earthing for all equipment shall also included All MCCBs / MCBs shall be of 10 KA breaking capacity and suitable for motor duty application. All motor starters shall be provided with Automatic level controller DOL starters shall be used for motors below 7.5 HP and Star-Delta Starters for other motors . Provision shall be made for providing potential free contacts to all pumps starters & shall be compatible to BMS with open protocol MCC for all STP equipments/pumps as described in sub head II

TOTAL JOB AS PER AOBVE SEPCS.

Description of Work / Item(s)

Amount

SITC of 30W 6ft linear suspended, high efficiency long life Product would look neat and clean with down diffused light Linear suspended luminaire with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser with 100% downward light distribution LED driver duly wired up to terminal block for easy installation and long service.CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 2700K to 6500K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, LED Driver shall be CCT tunable constructed, Isolated type, Multistage, Isolated Constant Current-Constant Voltage operated driver with range 100-240V AC and Safety Extra Low Voltage (SELV)<60V DC as per IEC standard & with 2 KV internal surge protection, Power factor greater than 0.95 and total harmonic distortion (THD) of less than 10% should be integral to the luminaire. Compliance to Indian Standards of IS10322 Part 5 / Sect 1:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012. Lumen Output - CCT wise - 3000 lumens (6500K), 2300 lumens (5700K), 2700 lumens (4000K) & 2475 lumens (2700K)/ WIPRO MODEL NO - Axeon LM34-411 (Colour Tunable)(6feet) or its equivalent make

SITC of 20W 2ft linear suspended, high efficiency long life Product would look neat and clean with down diffused light Linear suspended luminaire with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser with 100% downward light distribution LED driver duly wired up to terminal block for easy installation and long service.CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 2700K to 6500K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, LED Driver shall be CCT tunable constructed, Isolated type, Multistage, Isolated Constant Current-Constant Voltage operated driver with range 100-240V AC and Safety Extra Low Voltage (SELV)<60V DC as per IEC standard & with 2 KV internal surge protection, Power factor greater than 0.95 and total harmonic distortion (THD) of less than 10% should be integral to the luminaire. Compliance to Indian Standards of IS10322 Part 5 / Sect 1:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012. Lumen Output - CCT wise - 2000 lumens (6500K), 2200 lumens (5700K), 1800 lumens (4000K) & 1650 lumens (2700K) /WIPRO MODEL NO - Axeon LM34-251 (Colour Tunable)(2feet)or equivalent

SITC of 30W 6ft, DALI Dimmable High efficiency long life Linear suspended luminaire with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser. LED driver duly wired up to terminal block for easy installation and long service. Luminous efficacy not less than 110lm/W. CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 5700K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 3300lm./WIPRO MODEL NO - Axeon LM34-411 (DALIDimmable)5700K (6feet) or its equivalent make

SITC of 20W 2ft, DALI Dimmable High efficiency long life Linear suspended luminaire with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser. LED driver duly wired up to terminal block for easy installation and long service. Luminous efficacy not less than 110lm/W. CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 5700K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 2200lm./WIPRO MODEL NO - Axeon LM34-101 (DALIDimmable) 5700K (2feet) or its equivalent make

SITC of Axeon 300mm downlight 90 deg. non integral module 2700K-6500K, White body WIPRO MODEL NO - LM34-930-90L (Colour Tunable) or its equivalent make and model

SITC of Axeon 300mm downlight 60 deg. V non integral module2700K-6500K, White body WIPRO MODEL NO - LM34-930-60V (Colour Tunable) or its equivalent make and model

SITC of Axeon 300mm downlight 120 deg. V non integral module2700K-6500K, White body WIPRO MODEL NO - LM34-930-120V (Colour Tunable) or its equivalent make and model

SITC of Axeon 300mm downlight 120 deg. Y non integral module2700K-6500K, White body WIPRO MODEL NO - LM34-141-120Y (Colour Tunable) or its equivalent make and model

SITC of Axeon 300mm downlight 90 deg. T non integral module2700K-6500K, White body WIPRO MODEL NO - LM34-930-90T (Colour Tunable) or its equivalent make and model

SITC of Axeon 300mm downlight 90 deg. + non integral module2700K-6500K, White body WIPRO MODEL NO - LM34-930-90+ (Colour Tunable) or its equivalent make and model

SITC of 10W 2ft linear suspended, high efficiency long life Product would look neat and clean with down diffused light Linear suspended luminaire with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser with 100% downward light distribution LED driver duly wired up to terminal block for easy installation and long service.CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 2700K to 6500K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, LED Driver shall be CCT tunable constructed, Isolated type, Multistage, Isolated Constant Current-Constant Voltage operated driver with range 100-240V AC and Safety Extra Low Voltage (SELV)<60V DC as per IEC standard & with 2 KV internal surge protection, Power factor greater than 0.95 and total harmonic distortion (THD) of less than 10% should be integral to the luminaire. Compliance to Indian Standards of IS10322 Part 5 / Sect 1:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012. Lumen Output - CCT wise - 950 lumens (6500K), 1000 lumens (5700K), 850 lumens (4000K) & 800 lumens (2700K)/WIPRO MODEL NO - Stylus LM43-161 (Colour Tunable)(2Feet) or its equivalent make and model

SITC of 15W 3ft linear suspended, high efficiency long life Product would look neat and clean with down diffused light Linear suspended luminaire with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser with 100% downward light distribution LED driver duly wired up to terminal block for easy installation and long service.CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 2700K to 6500K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, LED Driver shall be CCT tunable constructed, Isolated type, Multistage, Isolated Constant Current-Constant Voltage operated driver with range 100-240V AC and Safety Extra Low Voltage (SELV)<60V DC as per IEC standard & with 2 KV internal surge protection, Power factor greater than 0.95 and total harmonic distortion (THD) of less than 10% should be integral to the luminaire. Compliance to Indian Standards of IS10322 Part 5 / Sect 1:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012. Lumen Output - CCT wise - 1425 lumens (6500K), 1500 lumens (5700K), 1275 lumens (4000K) & 1200 lumens (2700K)WIPRO MODEL NO - Stylus LM43-241 (Colour Tunable) (3Feet) or its equivalent make and model

SITC of 20W 4ft linear suspended, high efficiency long life Product would look neat and clean with down diffused light Linear suspended luminaire with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser with 100% downward light distribution LED driver duly wired up to terminal block for easy installation and long service.CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 2700K to 6500K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, LED Driver shall be CCT tunable constructed, Isolated type, Multistage, Isolated Constant Current-Constant Voltage operated driver with range 100-240V AC and Safety Extra Low Voltage (SELV)<60V DC as per IEC standard & with 2 KV internal surge protection, Power factor greater than 0.95 and total harmonic distortion (THD) of less than 10% should be integral to the luminaire. Compliance to Indian Standards of IS10322 Part 5 / Sect 1:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012. Lumen Output - CCT wise - 1900 lumens (6500K), 2000 lumens (5700K), 1700 lumens (4000K) & 1600 lumens (2700K)WIPRO MODEL NO - Stylus LM43-321 (Colour Tunable) (4Feet) or its equivalent make and model

SITC of 30W 6ft linear suspended, high efficiency long life Product would look neat and clean with down diffused light Linear suspended luminaire with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser with 100% downward light distribution LED driver duly wired up to terminal block for easy installation and long service.CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 2700K to 6500K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, LED Driver shall be CCT tunable constructed, Isolated type, Multistage, Isolated Constant Current-Constant Voltage operated driver with range 100-240V AC and Safety Extra Low Voltage (SELV)<60V DC as per IEC standard & with 2 KV internal surge protection, Power factor greater than 0.95 and total harmonic distortion (THD) of less than 10% should be integral to the luminaire. Compliance to Indian Standards of IS10322 Part 5 / Sect 1:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012. Lumen Output - CCT wise - 2850 lumens (6500K), 3000 lumens (5700K), 2550 lumens (4000K) & 2400 lumens (2700K)/WIPRO MODEL NO - Stylus LM43-481 (Colour Tunable)(6Feet) or its equivalent make and model

SITC of 40W 8ft linear suspended, high efficiency long life Product would look neat and clean with down diffused light Linear suspended luminaire with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser with 100% downward light distribution LED driver duly wired up to terminal block for easy installation and long service.CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 2700K to 6500K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, LED Driver shall be CCT tunable constructed, Isolated type, Multistage, Isolated Constant Current-Constant Voltage operated driver with range 100-240V AC and Safety Extra Low Voltage (SELV)<60V DC as per IEC standard & with 2 KV internal surge protection, Power factor greater than 0.95 and total harmonic distortion (THD) of less than 10% should be integral to the luminaire. Compliance to Indian Standards of IS10322 Part 5 / Sect 1:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012. Lumen Output - CCT wise - 3800 lumens (6500K), 4000 lumens (5700K), 3400 lumens (4000K) & 3200 lumens (2700K)/WIPRO MODEL NO - Stylus LM43-651 (Colour Tunable)(8Feet) or its equivalent make and model

SITC of 10W 2ft, DALI Dimmable High efficiency long life Product would look neat and clean with deep Inset diffuser brings a low glare light Linear suspended luminaire with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser. LED driver duly wired up to terminal block for easy installation and long service.CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 5700K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 1000lm./WIPRO MODEL NO - Stylus LM43-161 (Dali Dimmable) 5700K (2Feet) or its equivalent make and model

SITC of 15W 3ft, DALI Dimmable High efficiency long life Product would look neat and clean with deep Inset diffuser brings a low glare light Linear suspended luminaire with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser. LED driver duly wired up to terminal block for easy installation and long service.CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 5700K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 1500lm./WIPRO MODEL NO - Stylus LM43-241 (Dali Dimmable) 5700K (3Feet) or its equivalent make and model

SITC of 20W 4ft, DALI Dimmable High efficiency long life Product would look neat and clean with deep Inset diffuser brings a low glare light Linear suspended luminaire with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser. LED driver duly wired up to terminal block for easy installation and long service.CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 5700K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 2000lm./WIPRO MODEL NO - Stylus LM43-321 (Dali Dimmable) 5700K (4Feet) or its equivalent make and model

SITC of 30W 6ft, DALI Dimmable High efficiency long life Product would look neat and clean with deep Inset diffuser brings a low glare light. Linear suspended luminaire with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser. LED driver duly wired up to terminal block for easy installation and long service.CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 5700K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 3000lm./WIPRO MODEL NO - Stylus LM43-481 (Dali Dimmable) 5700K(6Feet) or its equivalent make and model

SITC of 40W 8ft, DALI Dimmable High efficiency long life Product would look neat and clean with deep Inset diffuser brings a low glare light. Linear suspended luminaire with white powder coated finish extruded aluminium housing. Special translucent satin finish colourLED PMMA Diffuser. LED driver duly wired up to terminal block for easy installation and long service.CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 5700K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 4000lm./WIPRO MODEL NO - Stylus LM43-651 (Dali Dimmable) 5700K(8Feet) or its equivalent make and model

SITC of Stylus Suspended LED downlighter is a connecting hub for linear fixture which in turn can be swiveled between 90 ° to 120°. Two arm joining 90° to 270°, Three arm joining 90° to 120° and Four arm joining 90°. It provides uniform down light when connected with adjacent linear fixture. White Matt Powder Coated extruded aluminum Housing Also available in Black Also available in 5700K CCT WIPRO MODEL NO - Stylus LM43-161XXX-(Dali Dimmable) 5700K or its equivalent make and model

SITC of Stylus 90 Deg L connector Module: 10W L module with 150mm arm for end to end connection. High efficiency long life Product would look neat and clean with deep Inset diffuser brings a low glare light and . Linear suspended luminaire with white powder coated finish extruded aluminium housing.LED driver duly wired up to terminal block for easy installation and long service.CRI>80, IP20, CCT- 2700K-6500K, 50,000 hrs @ L70 life. WIPRO MODEL NO - LM43-161-90L (Colour Tunable)or its equivalent make and model

SITC of Stylus 120 Deg V connector Module: 10W V module with 150mm arm for end to end connection. High efficiency long life Product would look neat and clean with deep Inset diffuser brings a low glare light and . Linear suspended luminaire with white powder coated finish extruded aluminium housing.LED driver duly wired up to terminal block for easy installation and long service.CRI>80, IP20, CCT- 2700K-6500K, 50,000 hrs @ L70 life. WIPRO MODEL NO - LM43-161-120V (Colour Tunable)or its equivalent make and model

SITC of Stylus 120 Deg Y connector Module: 15W Y module with 150mm arm for end to end connection. High efficiency long life Product would look neat and clean with deep Inset diffuser brings a low glare light and . Linear suspended luminaire with white powder coated finish extruded aluminium housing.LED driver duly wired up to terminal block for easy installation and long service.CRI>80, IP20, CCT- 2700K-6500K, 50,000 hrs @ L70 life. WIPRO MODEL NO - LM43-241-120Y (Colour Tunable)or its equivalent make and model

SITC of Stylus 90 Deg + connector Module: 15W T module with 150mm arm for end to end connection. High efficiency long life Product would look neat and clean with deep Inset diffuser brings a low glare light and . Linear suspended luminaire with white powder coated finish extruded aluminium housing.LED driver duly wired up to terminal block for easy installation and long service.CRI>80, IP20, CCT- 2700K-6500K, 50,000 hrs @ L70 life. WIPRO MODEL NO - LM43-241-90 T (Colour Tunable)or its equivalent make and model

SITC of Stylus 90 Deg + connector Module: 20W + module with 150mm arm for end to end connection. High efficiency long life Product would look neat and clean with deep Inset diffuser brings a low glare light and . Linear suspended luminaire with white powder coated finish extruded aluminium housing.LED driver duly wired up to terminal block for easy installation and long service.CRI>80, IP20, CCT- 2700K-6500K, 50,000 hrs @ L70 life. WIPRO MODEL NO - LM43-241-90 + (Colour Tunable)or its equivalent make and model

SITC of Integral, SMD 2x2 LED, IP 20, 33W LED Suspended fixture. Luminaire with versatile LED with white powder coated rough aluminium extruded housing. Luminaire shall have polycarbonate diffuser for Uniform illumination and wider light distribution. LM 80-08 compliant LEDs from reputed makes such as Nichia/ Cree/ Bridgelux/Lumiled/Citizen should be provided. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. Luminaire shall use SMD type LED. The LED shall be compliant with LM80-08 standard with Useful L70 life of 50000 Hrs tested at maximum current (Complete LM 80 test report for LED should be submitted for 10000 hrs of testing). The LEDs used should be with CCT of 2700K to 6500K and CRI of Minimum 80. LED Driver shall be CCT tunable constructed, Isolated type, Multistage, Isolated Constant Current-Constant Voltage operated driver with range 100-240V AC and Safety Extra Low Voltage (SELV)<60V DC as per IEC standard & with 2 KV internal surge protection, Power factor greater than 0.95 and total harmonic distortion (THD) of less than 10% should be integral to the luminaire. Compliance to Indian Standards of IS10322 Part 5 / Sect 1:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012 Lumen Output - CCT wise - 2800 lumens (6500K), 3069 lumens (5700K), 2700 lumens (4000K) & 2400 lumens (2700K)/WIPRO MODEL NO - Verge LM29-451 (Colour Tunable) or its equivalent make and model

SITC of Integral, SMD 2x2 LED, IP 20, 33W LED Recess mounted fixture. Luminaire with versatile LED with white powder coated rough aluminium extruded housing. Luminaire shall have polycarbonate diffuser for Uniform illumination and wider light distribution. LM 80-08 compliant LEDs from reputed makes such as Nichia/ Cree/ Bridgelux/Lumiled/Citizen should be provided. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. Luminaire shall use SMD type LED. The LED shall be compliant with LM80-08 standard with Useful L70 life of 50000 Hrs tested at maximum current (Complete LM 80 test report for LED should be submitted for 10000 hrs of testing). The LEDs used should be with CCT of 2700K to 6500K and CRI of Minimum 80. LED Driver shall be CCT tunable constructed, Isolated type, Multistage, Isolated Constant Current-Constant Voltage operated driver with range 100-240V AC and Safety Extra Low Voltage (SELV)<60V DC as per IEC standard & with 2 KV internal surge protection, Power factor greater than 0.95 and total harmonic distortion (THD) of less than 10% should be integral to the luminaire. Compliance to Indian Standards of IS10322 Part 5 / Sect 1:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012 Lumen Output - CCT wise - 2800 lumens (6500K), 3069 lumens (5700K), 2700 lumens (4000K) & 2400 lumens (2700K)/WIPRO MODEL NO - Verge LM29-451 (Colour Tunable) or its equivalent make and model

SITC of Integral, SMD 2x2 LED, IP 20, 33W LED Suspended DALI Dimmable fixture with System efficacy of more than 93lm/W and system lumen output 3069lm.. Luminaire with versatile LED with white powder coated rough aluminium extruded housing. Luminaire shall have polycarbonate diffuser for Uniform illumination and wider light distribution. LM 80-08 compliant LEDs from reputed makes such as Nichia / Cree / Bridgelux / Lumileds should be provided. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. Luminaire shall use SMD type LED. The LED shall be compliant with LM80-08 standard with L70 life of 50000 Hrs tested at maximum current (Complete LM 80 test report for LED should be submitted for 10000 hrs of testing). The LEDs used should be with CCT of 5700 K and CRI of Minimum 80. LED Driver shall be Multistage, Isolated type, APFC, Constant Current topology driver with proper heat sink for heat dissipation suitable to operate in input voltage range of 150V to 270V (nominal rated voltage – 240V) with 2KV internal surge protection, Power factor greater than 0.95 and total harmonic distortion (THD) of less than 10% should be integral to the luminaire. Complying to SELV < 60V DC standards. Compliance to Indian Standards of IS10322 Part 5 / Sect 1:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012. WIPRO MODEL NO - Verge LM29-451 (Dali Dimmable) 5700K or its equivalent make and model

SITC of Integral, SMD 2x2 LED, IP 20, 33W LED Recess mounted DALI Dimmable fixture with System efficacy of more than 93lm/W and system lumen output 3069lm.. Luminaire with versatile LED with white powder coated rough aluminium extruded housing. Luminaire shall have polycarbonate diffuser for Uniform illumination and wider light distribution. LM 80-08 compliant LEDs from reputed makes such as Nichia / Cree / Bridgelux / Lumileds should be provided. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. Luminaire shall use SMD type LED. The LED shall be compliant with LM80-08 standard with L70 life of 50000 Hrs tested at maximum current (Complete LM 80 test report for LED should be submitted for 10000 hrs of testing). The LEDs used should be with CCT of 5700 K and CRI of Minimum 80. LED Driver shall be Multistage, Isolated type, APFC, Constant Current topology driver with proper heat sink for heat dissipation suitable to operate in input voltage range of 150V to 270V (nominal rated voltage – 240V) with 2KV internal surge protection, Power factor greater than 0.95 and total harmonic distortion (THD) of less than 10% should be integral to the luminaire. Complying to SELV < 60V DC standards. Compliance to Indian Standards of IS10322 Part 5 / Sect 1:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012. WIPRO MODEL NO - Verge LM29-451 (Dali Dimmable) 5700K or its equivalent make and model

OnAIR Down: SITC of 30W 4ft, High efficiency Linear up down edgelitLED DALI Dimmable luminaire with low glare light. suspended luminaire with White Matt Powder Coated extruded aluminum Housing. Edge lit optics derived from Reflector+ Light guide plate+ Diffuser configuration. CRI>80, IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, CCT- 5700K, 50,000 hrs @ L70 life, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire Efficacy > 95 lm/W./WIPRO MODEL NO - OnAir LM44-501 (Dali Dimmable) 5700K or its equivalent make and model

SITC of 10 to 33W per meter as per requirement Shape & Length will be design as per Site requirement WIPRO MODEL NO -AQUA LM69 (Dali Dimmable) 4000K or its equivalent make and model

VERTICA LED DOWNLIGHT: (36 deg beam) SITC of 20W, High efficiency surface/suspended DALI Dimmable downlighter designed with aluminum body powder coated in white or black and clear glass COB LED. CRI>80, IP20, Ambient temp- 0 to 45 DegC, Driver efficiency>85%, THD<20%,Powerfactor>0.9, CCT - 4000K, 50,000 hrs @ L70 life.Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 140-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 1600 lm. (80 lm/W)/WIPRO MODEL NO - VERTICA LD30-201-36 (Dali Dimmable) 4000K or its equivalent make and model

VERTICA LED DOWNLIGHT: (36 deg beam) SITC of 30W, High efficiency surface/suspended downlighter designed with aluminum body powder coated in white or black and clear glass COB LED. CRI>80, IP20, Ambient temp- 0 to 45 DegC, Driver efficiency>85%, THD<20%,Powerfactor>0.9, CCT - 4000K/5700K, 50,000 hrs @ L70 life.Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 140-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 2400 lm. (80 lm/W)/WIPRO MODEL NO - VERTICA LD30-301-36W (Dali Dimmable) 4000K or its equivalent make and model

Hexa Ring: SITC of 35W, High efficient suspended LED Housing made up of extruded Aluminum powder coated and non-yellowing PMMA diffuser. Aesthetic slim profile in ring type with edge lit concept for contemporary interiors.Revolutionary disc of light with horizontal plane creates circle of light. CRI>80, IP20, Ambient temp-0 to 45 Deg C, CCT - 4000K/5700K, 50,000 hrs @ L70 life.Driver efficiency>85%, THD<15%, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 3150 lm. (90 lm/W)/WIPRO MODEL NO - HEXA RING LM23HR-601-(Dali Dimmable) 4000K or its equivalent make and model

ORBIT RING: SITC of 35W, High efficient suspended LED Housing made up of extruded Aluminum powder coated and non-yellowing PMMA diffuser. Aesthetic slim profile in ring type with edge lit concept for contemporary interiors.Revolutionary disc of light with horizontal plane creates circle of light. CRI>80, IP20, Ambient temp-0 to 45 Deg C, CCT - 4000K/5700K, 50,000 hrs @ L70 life.Driver efficiency>85%, THD<15%, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 3500 lm. (100 lm/W)/WIPRO MODEL NO - Orbit Ring LM23OR-621-(Dali Dimmable) 4000K or its equivalent make and model

MOLLIS LED DOWNLIGHT: SITC of 12W, High efficient recess mounted LED round DALI Dimmable downlighter with white powder coated, pressure die cast aluminium housing. High transmittivity PS diffuser provides soft light. CRI>80, IP20, Ambient temp-0 to 45DegC, CCT - 4000/5700K, 50,000 hrs @ L70 life.Driver efficiency>85%, THD<10%, Powerfactor>0.9, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 90-265V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 1200 lm. (100 lm/W) - Cutout Dia-ø110mm/WIPRO MODEL NO - Mollis LD06-151 (Dali Dimmable) 5700K or its equivalent make and model

MOLLIS LED DOWNLIGHT: SITC of 15W, High efficient recess mounted LED round DALI Dimmable downlighter with white powder coated, pressure die cast aluminium housing. High transmittivity PS diffuser provides soft light. CRI>80, IP20, Ambient temp-0 to 45DegC, CCT - 4000/5700K, 50,000 hrs @ L70 life. Driver efficiency>85%, THD<10%, Powerfactor>0.9, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 90-265V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 1500 lm. (100 lm/W) - Cutout Dia-ø145mm/WIPRO MODEL NO - Mollis LD06-171 or Equivalent make (Dali Dimmable) 5700K or its equivalent make and model

SITC of Integral, SMD 2x2 LED, IP 20, 30W LED Recess mounted fixture with System efficacy of more than 120lm/W and system lumen output 3750lm. Luminaire shall have satin finished translucence (HET) diffuser for Uniform illumination and wider light distribution. LM 80-08 compliant LEDs from reputed makes such as Nichia / Cree / Bridgelux / Lumileds should be provided. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. Luminaire shall use SMD type LED. The LED shall be compliant with LM80-08 standard with L70 life of 50000 Hrs tested at maximum current (Complete LM 80 test report for LED should be submitted for 10000 hrs of testing). The LEDs used should be with CCT of 5700 K and CRI of Minimum 80. LED Driver shall be Multistage, Isolated type, APFC, Constant Current topology driver with proper heat sink for heat dissipation suitable to operate in input voltage range of 150V to 270V (nominal rated voltage – 240V) with 2KV internal surge protection, Power factor greater than 0.95 and total harmonic distortion (THD) of less than 10% should be integral to the luminaire. Complying to SELV < 60V DC standards. Compliance to Indian Standards of IS10322 Part 5 / Sect 1:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012/WIPRO MODEL NO - Immaculate Plus CRCO10R030DA57HEG2 or its equivalent make and model

FOKUS Plus LED Downlight: SITC of 12W, High efficient deep recess mounted COB LED DALI Dimmable downlighter with extruded aluminium housing with UGR<19. High efficiency PC frosted reflector optics for effictive thernmal management using aluminium casting. CRI>80, CCT - 4000K, 50,000 hrs @ L70 life.IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Cutout Dia-ø70mm. Luminaire lumen ≥ 1200 lm. (100 lm/W)/WIPRO MODEL NO - Fokus LD07-131-060 (Dali Dimmable) 4000K or its equivalent make and model

FOKUS Plus LED Downlight: SITC of 15W, High efficient deep recess mounted COB LED DALI Dimmable downlighter with extruded aluminium housing with UGR<19. High efficiency PC frosted reflector optics for effictive thernmal management using aluminium casting. CRI>80, CCT - 4000K, 50,000 hrs @ L70 life.IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Cutout Dia-ø100mm. Luminaire lumen ≥ 1500 lm. (100 lm/W)/WIPRO MODEL NO - Fokus LD07-161-050 (Dali Dimmable) 4000K or its equivalent make and model

FOKUS Plus LED Downlight: SITC of 30W, High efficient deep recess mounted COB LED downlighter with extruded aluminium housing with UGR<19. High efficiency PC frosted reflector optics for effictive thernmal management using aluminium casting. CRI>80, CCT - 4000K, 50,000 hrs @ L70 life.IP20, Ambient temp-0 to 45DegC, Driver efficiency>85%, THD<10%, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Cutout Dia-ø100mm. Luminaire lumen ≥ 1800 lm. (100 lm/W)/WIPRO MODEL NO - Fokus LD07-381-045(Dali Dimmable) 4000K or its equivalent make and model

ARC LED: SITC of 30W, High efficient Arc shape made of aluminium white colour coated outside finish. LED's provided with high efficient non yellowing PMMA diffuser provides soft light.CRI>80, IP20, Ambient temp-0 to 45 Deg C, CCT - 4000K, 50,000 hrs @ L70 life. Driver efficiency>85%, THD<15%, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 2160 lm. (72 lm/W)/WIPRO MODEL NO - ARC LM48-341-XXX-40-WH or its equivalent make and model

CONE LED: SITC of 20W, High efficient Cone shape made of aluminium white colour coated outside finish. LED's provided with high efficient non yellowing PMMA diffuser provides soft light.CRI>80, IP20, Ambient temp-0 to 45 Deg C, CCT - 4000K, 50,000 hrs @ L70 life. Driver efficiency>85%, THD<15%, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 1440 lm. (72 lm/W)/WIPRO MODEL NO - Cone LM45-221-XXX-40-WH or its equivalent make and model

CORAL LED: SITC of 30W, High efficient coral (bell) shape made of aluminium white colour coated outside finish. LED's provided with high efficient non yellowing PMMA diffuser provides soft light.CRI>80, IP20, Ambient temp-0 to 45 Deg C, CCT - 4000K, 50,000 hrs @ L70 life. Driver efficiency>85%, THD<15%, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 2160 lm. (72 lm/W)/WIPRO MODEL NO - Coral LM56-301-XXX-40-WH or its equivalent make and model

OZONE LED: 30W, High efficient trapezoidal round shaped made of aluminium white colour coated outside finish. LED's provided with high efficient non yellowing PMMA diffuser provides soft light.CRI>80, IP20, Ambient temp-0 to 45 Deg C, CCT - 4000K, 50,000 hrs @ L70 life. Driver efficiency>85%, THD<15%, Powerfactor>0.95, Surge protection-2 kV, Multistage Isolated Constant Current-Constant Voltage operated driver with range 150-270V AC and Safety Extra Low Voltage Safe level<60V DC as per IEC standard. Luminaire lumen ≥ 2160 lm. (72 lm/W)/WIPRO MODEL NO - Ozone LM57-301-XXX-40-WH or its Equivalent make and model

Automation

DALI Controller/Gateway : Supply Installation testing & commissioning of DALI gateway system uses standard Ethernet communication. Its modularity allows to design scalable systems, from a single office room to a large office building. Device capable of manage 128 dali ballast and din rail mounted product. The system communication bus could be on KNX protocol.

0-10 Analogue Dimmer :Supply Installation testing & commissioning of 4 Channel Ballast Controller (Dimming Module) It is DIN Rail Mounted Device . The device is also equipped with 16A contacts each for switching light loads. Each output can be managed via a button on board. The system communication bus could be on KNX protocol.

Smart Keypads: Supply Installation testing & commissioning of keypad equipped with 4 completely independent and configurable channels able to perform a wide range of functions . The system communication bus could be on KNX protocol.

Power supply for the bus:Supply Installation testing & commissioning of Power Supply Unit, and provides power to the system with input voltage of 120 -230 V at 50-60Hz. The system communication bus could be on KNX protocol.

Integrated Day Light Sensor with occupancy control : Supply Installation testing & commissioning of Of Integrated Presence detector suitable for ceiling mounting , manages the detection and includes a brightness sensor for environmental lighting control. The presence detection solution should be able to deduce the presence of people in the room using one or more dedicated sensors. The device should be able to manage the ambient lighting based on the measured illuminance; it is also possible to enable the logic called “Circadian Rhythm” with which brightness and color temperature are imposed on the basis of predefined curves or on the basis of the real position of the sun during the day with respect to a terrestrial coordinate.This function allows you to recreate lighting comfort in an environment as close as possible to reality. It’s possible to use predefined algorithms as proportional controls of temperature and humidity or dew point calculation. The system communication bus could be on KNX protocol.

IP Router: Supply Installation testing & commissioning of of ip router which provides with the tunneling protocol a connection point for ETS to allow commissioning and monitoring.

Bus Coupler :Supply Installation testing & commissioning of of KNX coupler, to be used for the bidirectional exchange of data between two KNX lines ensuring galvanic isolation

Processor for Integration : Supply Installation testing & commissioning of controller (if required for the functionality of the system). Specification of the controller being: The Controller should be with multi-Purpose Output Ports 3.5mm jacks Compatible with industry-standard IR emitters IR Output Drive 100mA maximum (per port, adjustables)200mA maximum (high IR output port)Infrared Frequency Transmission Range 15 KHz - 460 KHz Infrared Input Compatible with industry-standard repeaters and receivers. Trigger Outputs minimum Three, 12VDC, 100mA max each Relays minimum Three, 3 amps @ 30VDC Sense Inputs Three, 3-24VDC RS-232 Ports minimum Three, Bi-directional RJ45 Connections Ethernet Port 10/100Base-T, RJ45 Connection USB Ports minimum OneCOM Port Zigbee® Communication Port, RJ45 Connection Mounting Rack-mount or free standingOperating Temperature +32°F to +122°F (0°C to +50°C)Operating Humidity 5% to 95% Non-condensing (to be considered only if required for the functionality of the system). With BMS integration package. The hardware should be such that fulfills the requirements of site.

Relay For Curtain Control : Supply Installation testing & commissioning of All-in-one multi-application controller with 20 outputs capable of performing multiple functions including:ON-OFF lights control ,Control of shutters and curtains, Control of controlled sockets and control of fan coils with 2 and 3 point valves.Suitable for managing resistive, capacitive, inductive loads and fluorescent lamps with different functions. The system communication bus could be on KNX protocol.

Curtain Motors : Supply Installation testing & commissioning of Low Noise 4 Wire/ 5 Wire 230 Volt tubular motor with appropriate alumunium tube for blinds. Torque should be 10 Nm or higher should be comaptible with a third party automation system. The motor should be able to sustain a blind load of 30 Kg.

Communication Cable : KNX Communication Cable 305 Meter Drum (to be considered only if required for the functionality of the system) Applicable Technical Standard: KNX Certified: 579/17212/20 Construction Conductor: Solid OFC annealed bare copper wire 0.80 ± 0.015mm (20AWG) nsulation: Polyethylene 1.6mm ± 0.05mm Cable lay up: Four cores twisted together with surrounding fabric and foil shieldin Conductor colour code: White, Red, Yellow and Black Shielding: Nonwoven fabric 125% coverage & Al-Mylar (Al facing outwards) 125% coverage Drain wire: Tinned copper wire 0.408 ± 0.008m Jacket material: Low Smoke Zero Halogen Outer diameter: 6.00 ± 0.2mm Mechanical Properties Bend radius without load: 31.5mm Bend radius with load: 63.0mm Temperature range during operation: -20°C — 70° Temperature range during installation: -30°C — 70°C Electrical PropertiesDC resistance: nom. 36.7Ω/km Capacitance: 50pF/mVoltage rating: 300V Test voltage: 4kV, 1 min

Application for Control :Supply Intallation Testing & Commissioning of Central Monitoring & control application.The application should be customizable Integration Designer programming software, theapplication should offers the same intuitive control experience , running on a mobile device as well as on a Windows® PC. Providing secure local or remote access to the system from any Internet connection, the application allows for control via LAN, Wi-Fi and WAN control off site. When used with an control processor, users can view and adjust thermostats, monitor security systems and turn off lights, in addition to controlling their A/V electronics, from the office, on vacation, or virtually anywhere in between. The application should be compatible over phone and PC and should support IOs, android and windows platforms.

Stand AloneOccupancy Sensor :Supply Installation testing & commissioning of Of standalone PIR occupancy detection sensor. This device automatically controls a light source by detecting movement in its supervision zone. 360° detection angle motion detector.Detection type: infra-red.Mounting: ceiling

Supply , Installation, Testing and Comissioning of 8 port Unmanaged Switch Plug-and-play - easy setup with no configuration or no software needed, following Port fast ethernet - 8 port 10/100 MBPS auto-negotiation RJ45 ports, IEEE 802.3x flow control ,supports auto-MDI/MDIX, eliminating the need for crossover cables including making connection etc as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with PWD Electrical 2022 BSR .

Description of Work / Item(s)

Amount

IP BASED CCTV SYSTEM

5 MP IR Fixed Dome Network Camera -1/2.7″ Progressive Scan CMOS, 2592 × 1944 at 25fps, 2.8 mm Fixed lens, 0.003 Lux at F1.4, 0 Lux with IR on, ICR, ONVIF (PROFILE S, PROFILE G, PROFILE T), support H.265, H.264, MJPEG, 120db WDR, BLC, HLC, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 256 GB (SD card not included), Alarm : 1 inputs & 1 outputs, Audio: 1 input & 1 output, Built-in Microphone, , IP67, IK 10, Edge Analytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Face capture, Region entrance detection, Region exiting detection, Video tampering, Audio exception detection, Focus on human and vehicle targets classification based on deep learning UL/BIS, CE, FCC certified.

SITC of 64ch Network Video Recorder- Connect Up to 64 IP Cameras, Up to 12 Megapixels Resolution, HDMI1/VGA1 and HDMI2/VGA2 outputs provided, atleast one HDMI output of 4K resolution, atleast 1 VGA output with output upto 1920 × 1080, Support H.265, H.264, Supports RAID0, RAID1, RAID5, RAID6 and RAID10, Supports HDD hot swap, ,Incoming Bandwidth 320 Mbps, 8 SATA Hard Disks, 1 eSATA interface, ANR Technology, 8 SATA interfaces for 8 HDDs and capacity of each HDD upto 10TB, 3 × USB at least 1 × USB with 3.0, Alarm I/O 16/4, RS-485, RS-232, 2 RJ-45 10 /100/1000 Mbps self-adaptive Ethernet interface,UL/BIS, CE, FCC certified. Refer to detailed tech specs & Approved makes as per RFP.

SITC of 6TB Surveillance Hard Disk for NVR (Refer to detailed tech specs & Approved makes as per RFP.)

VIDEO MANAGEMENT SOFTWARE

SITC of Video Management Software - Refer to detailed tech specs & Approved makes as per RFP.

SITC of VMS server and client PC hardware to install VMS Software -Refer to detailed tech specs & Approved makes as per RFP.

BMS/Security Room Videowall

SITC of Video Wall 2X2 with 55" LCD as per detailed tech specs & Approved makes mentioned in RFP

SITC of Video wall controller with 4 Inputs with -Refer to detailed tech specs & Approved makes as mentioned in RFP

SITC of Cables Controller to Video Wall Panel for above

PA System

Supply Installation Testing & Commissioning of 500W RMS Dual Channel Class-D Digital Power Amplifier with Switch power technology for power electricity saving. Amplifier shall have Following Features: 500W RMS per Channel, Amplifier Output 100V, Short Circuit, Power, Tempreature, Overload Protection, Auto Cooling Fans. THD <0.1%, Frequency Response 20Hz - 20kHz, AC & DC Fuse, SNR >80dB.

Supplying, installing, testing and commissioning of Remote Paging microphone with minimum 12 buttons and Busy/Hole Indication. The Microphone Should be suitable for Desktop mounting. Shall have below features Configurable PPT paging mode and Normal Paging Mode. 9 Level of Con?gurable priority. Support 24V phantom Power Supply, System Capacity of 32 Unit Microphone. Signal transmission ensure distance up to 600 meters. Redundancy loop wiring for Microphone Supervision

Supply, Installation, Testing & Commissioning of of 6W Recessed Ceiling speakers with following features:-Speaker Drive 5", Complete metal grille and line matching transformer 100/70V line. Variable wattage tapings of 6 / 3/ 1.5 at 100v, Effective frequency range 110-15kHz (BS6840), SPL@1m/1W=91dB, Peak SPL 97dB complete with necessary mounting hardware & accessories.

Supply, Installation, Testing & Commissioning of of 6W wall mount speakers with following features:-component 7.5", Complete metal grille and line matching transformer 100/70V line. Variable wattage tapings of 5/10W, Effective frequency range 150-15kHz (BS6840), SPL@1m/1W=90dB, Peak SPL 98dB complete with necessary mounting hardware & accessories.

Supply, Installation, Testing & Commissioning of Network cables assembly and any applicable interfaces/cards/supervision modules for main controller, amplifier & paging microphone and any other devices as applicable.

Supply, Installation, Testing & Commissioning of CD player,Disc playback modes,USB Direct playback modes, Tuner / Reception / Transmission, Connectivity USB.

Supply, Installation, Testing & Commissioning of Web/Server based Software Application for System Configuration, Management & Diagnostics

Fire detection System

Addressable Fire Detection System Solution: SITC of UL864 10th Edition UL Listed and FM approved Analog Addressable 4 Loop Fire Alarm control panel (expandable upto 50 Loops using same CPU). Panel shall be running on full digital protocol with 32 bit Microprocessor . The Panel shall be complete with 6" color touch screen LCD Display. Fire alarm panel should have minimum capacity of 2500 detectors and devices in any combination and capable of making upto 10 loops in single panel using additional Loop cards. Each addressable loop shall be capable of taking 250 addresses per loop configuring either as all detectors or modules or any mix of both. The panel shall have the Fire Fighter Touch Screen Graphical Display panel to inform & guide Fire Fighters for carrying out Fire Fighting operations. The display shall have Hazmat icons indicating the presence of any explosive gas, liquids, poison,fumes etc. If this feature is not available in fire alarm panel then additional fire fighter touch panel along with necessary hardware and software should be provided by the manufacturers for fire fighters to guide them during emergency without any extra cost. To expedite system troubleshooting, the system cards shall have ground fault detection and diagnostic LEDs by card. In the display,simple building floor plan can be loaded in bitmap or jpeg format, On the map, the user will see an icon indicating the location of the event in the building in addition to a 'You-Are-Here' symbol to tell the responding person exactly where they are in the building in relation to the event. The system shall be polarity insensitive. The panel shall support degrade mode operation and shall have battery backup of 24 hrs in normal condition and 30 minutes in Alarm condition and BMS output connectivity.

SITC of UL864 10th Edition UL Listed and FM approved Analog Addressable Networkable Repeater panel having 32 bit Central processor and 6" colored touch screen LCD display. The panel shall have the Fire Fighter Touch Screen Graphical Display panel to inform & guide Fire Fighter for carring out Fire Fighter operation. The display shall have Hazmat icons indicating the presence of explosive gas, liquids, poison,fumes etc stored on the floor. If this feature is not available in Repeater panel then additional fire fighter touch panel along with necessary hardware and software should be provided by the manufacturers for fire fughters to guide them during emergency without any extra cost. The panel shall have 12 Amps inbuilt power supply having charging capacity of maximum 100AH Lead Acid battery. The panel shall have network card included inside the panel for RS485 communication with other display devices like Graphic screen, repeater panel etc. The panel shall have 5000 event, history-logging capability with online and offline reports. The panel shall support degrade mode operation and shall have battery backup of 24 hrs in normal condition and 30 minutes in Alarm condition.

Supply, Installation, Testing and Comissioning of 2 Core X 1.5 Sq.mm FRLS twisted pair shielded, PVC insulated armoured copper conductor cable.

SITC of UL268 6th and 7th edition compliance and FM approved Intelligent Addressable multi-criteria detector (optical and thermal sensors) complete with standard base, facility to mount in different comprehensive environment, Tri-color detector-status LED with 360 ° view, microprocessor circuitry with error check; detector self-diagnostics and supervision programs,Rate-of-Rise Detection: 15°F / min. (8.3°C / min.) - Fixed: 135°F (57°C) , Field programmable as rate-of-rise or fixed temperature, Polarity insensitive, Superior EMI and RFI immunity, RoHS compliant. Detector shall have in-built isolator for better reliability, circuit integrity and advanced fault finding. Manufacturers not having in-built Isolator feature in detector shall consider Isolator base in place of standard base OR separate Isolator before and after every detector to comply the same without any extra cost (Above Ceiling Level)

SITC of UL268 6th and 7th edition compliance and FM approved Intelligent Addressable multi-criteria detector (optical and thermal sensors) complete with standard base, facility to mount in different comprehensive environment, Tri-color detector-status LED with 360 ° view, microprocessor circuitry with error check; detector self-diagnostics and supervision programs,Rate-of-Rise Detection: 15°F / min. (8.3°C / min.) - Fixed: 135°F (57°C) , Field programmable as rate-of-rise or fixed temperature, Polarity insensitive, Superior EMI and RFI immunity, RoHS compliant. Detector shall have in-built isolator for better reliability, circuit integrity and advanced fault finding. Manufacturers not having in-built Isolator feature in detector shall consider Isolator base in place of standard base OR separate Isolator before and after every detector to comply the same without any extra cost (Below Ceiling Level)

SITC of UL listed and FM approved Intelligent addressable Class X type (Style 7), Manual Pull Station Single Action, Shock and Vibration Resistant, with built in dual isolator, polarity insensitive, Tri color LED for status (Green for Normal,Yellow for Faulty and RED for activation), T-45 Key Reset lockset for easy maintenance, Operating Temp and RH: 0-49degC and <=95%. MCP shall have in-built isolator for better reliability, circuit integrity and advanced fault finding. Manufacturers not having in-built Isolator feature shall provide separate Isolator before and after every MCP to comply the same without any extra cost.

SITC of UL Listed Sounder cum Strobe rated at 75 dBA @ 3m for Audible annunciation and 75cd flashintg at 1 Hz for visual indication.

SITC of UL listed and FM approved Intelligent addressable Class X type (Style 7), Monitor Module with built in dual isolator, polarity insensitive, Tri color LED for status (Green for Normal,Yellow for Faulty and RED for activation), Operating Temp and RH: 0-49degC and <=95%. Module shall have in-built isolator for better reliability, circuit integrity and advanced fault finding. Manufacturers not having in-built Isolator feature shall provide separate Isolator before and after every Module to comply the same without any extra cost. (For Sprinkler Flow Switches and door holders)

SITC of UL listed and FM approved Intelligent addressable Class X type (Style 7), Control Module with built in dual isolator, polarity insensitive, Tri color LED for status (Green for Normal,Yellow for Faulty and RED for activation), Operating Temp and RH: 0-49degC and <=95%. Module shall have in-built isolator for better reliability, circuit integrity and advanced fault finding. Manufacturers not having in-built Isolator feature shall provide separate Isolator before and after every Module to comply the same without any extra cost. (For AHU & Staircase Pressurization Fans, Hooters / Sounders / Strobes etc.)

SITC of UL Listed Addressable Fire Fighter's Telephone Jack with suitable module for two way communication between Remote Fire Fighter & Fire Command Center

SITC of UL Listed Fire Fighter's Telephone Handset for two way communication between Remote Fire Fighter & Fire Command Center.

Supply, Installation, Testing & Commissioning of Response indicator

Access Control System

Access Control and Time Attandance System Solution: Access Control Solution : Supply, Installation, Testing & Commissioning of Access Control Access System Monitoring Hardware Central Work Station Server with i9 with 11th gen. Intel processor with minimum 1TB SSD, 16 GB RAM SSD, 22" TFT Monitor, DVD Writer, two serial and one parallel ports, multimedia speakers, infrared mouse; Work station shall be preloaded with requisite MS Windows Licensed software compatible with the Access Control platform

Supply, Installation, Testing & Commissioning of 600 dpi or better A4 size laser color printer

Supply, Installation, Configuration, Programming Web based Access Management Software supports Real Time Monitoring with Auto Push Technology, Template Management, Anti Pass back, Time Zones, Access Time, Access Levels, Access Area, Access Groups & Scheduling, Wiegand Setting, Log Management, Audit Log Reports, Admin Authority Management to define rights of each user to perform, Blacklist User Management, Capable to integrate with 3rd party applications over Web API's with time attendace software for 500 users etc.

Supply, Installation, Testing & Commissioning of Multi modal Face Recognition cum Fingerprint with Smart Card & PIN based Reader cum door controller having minimum 5" LCD Display with Capacitive Touchscreen supports Walk Through Face authentication & verification from 0.3 meter to 3 meters, 256 bit encrypted algorithm to protect important information such as personal information transmitted, Support TLS standard security communication protocols, Live Face Detection with anti-spoofing against 2D photograph, mobile selfie and video, Fake Fingerprint Detection Technology, 20,000 Face Storage Capacity (1:N), 5,00,000 Users on 1:1; 10 million transaction storage capacity, 20,000 Image Logs, support operating illuminance up to 25,000 lux, In built Multi Class (EM & Mifare) Card Reader, Communication protocols like TCP/IP, OSDP/ Wiegand Out / IN, RS 485, USB, NFC, User wise authentication modes; Built in Lock Control; Onboard Dual Camera; Mask Detection & Alert (configurable); Support Thermal Module Integration for Body Temperature Detection, supports SDK/ Web API’s level integration, UL Listed Power Supply, CE, FCC, RoHS, BIS, WPC certifications etc. suitable for mounting on metal surface/metal frames/ wooden frames / wall / flap barriers or as required based on site conditions including all accessories

Supply, Installation, Testing & Commissioning of NO TOUCH Exit Switch with Metal Finish.

Supply, Installation, Termination & Commissioning of EM Magnetic Lock 600 LBS with Door Sense, Mounting Clamp.

Supply Installation Testing & Commissioning of EM Prox Card without Printing

Supply, Installation, Configuration, Programming & Customization of Access Control License. Comprehensive Access Control Management. Perpetual Cost for Time, User & Zone Based Access Control, Access Zones, Access Modes & Access Levels. Advanced Access Control features like 2-Person Rule, First-in User Rule, Anti-pass Back, Guard Tour, Duress Detection & More. Various Reports Generation, for 500 Users

Supply, Installation, Testing & Commissioning of Fingerprint and EM Proximity Card Based Door Controller, IP65 Rating, 50,000 Events and 9,600 Fingerprint Template Storage, Built-in PoE, Built-in Door Lock / Door Sense / Exit Reader / Exit Switch Ports, RS-485 and Ethernet Interfaces. Tri-color LED & Buzzer.

Supply, Installation, Testing & Commissioning of Exit Switch with Metal Finish.

Supply, Installation, Termination & Commissioning of Card and Biometric Enrollment Station, with EM Proximity Card Enrollment Module.

Network Switches

Supply, installation, testing and commissioning of Layer 2 switch with 48 ports (RJ-45) including SFP modules, rack mountable, SMPS power supply & other termination accessories (Like Pigtails/LIUs/ Convertors/Splicing equipment ,Patch panel, Patch Cord, Etc) complete as per specifications and as required for BMS DDC Panel Networking. The switch to switch distance shall not exceed beyond 80 meters.

Description of Work / Item(s)

Amount

Providing, fixing, testing and commissioning of white vitreous china wall mounted type European water closet with C.P. bolts, nuts, C.I. chair (painted with two coats of enamel paint over a coat of primer) or other hanging arrangements, built-in exposed white vitreous china low volume compatiable cistern with C.P. bolts, nuts, supporting arrangements, bakelite / poly propylene seat & cover with C.P. hinges & rubber buffers, complete with all accessories. Including cutting & making good the walls & floors wherever required.

Providing, fixing, testing & commissioning of concealed type cistern(low flow as per ECBC) with dual flush facility comprising of actuator button facia assembly including brass / SS screws and washer complete, providing protection cover over cistern, cutting and making good the walls wherever required. Make : Gabrit /Viega

Providing & fixing C.P brass toilet paper holder with PVC rawl plug & C.P. brass screw complete as required.

Providing, fixing, testing and commissioning of 15 mm dia C.P. brass 2 way cock with C.P. wall flange of approved quality and making good as required.

Providing, fixing, testing and commissionin Hand shower(Helth faucet) with 8 mm dia 1 mt long PVC tube &wall hook complete

Providing, fixing, Twin Coat hook

Providing & fixing first quality white vitreous china oval / round / square wash basin (size as per architectural drawing) for under counter mounting, specially fabricated CI / MS brackets, painted with two or three coats of enamel paint of approved shade over a coat of primer, 32 mm CP brass waste and CP brass cast bottle trap and pipe to wall with CP brass flange and rubber adopter for waste connection complete including filling gap between counter and wash basin with approved type poly sulphide sealant, cutting and making good the walls wherever required. WHITE JAQUAR MAKE

Providing, fixing, testing and commissioning of Basin PILLAR COCK WITH 200mm EXTENSION BODY Tall type .

Providing, fixing, testing and commissioning of C.P. brass angle valve with C.P. wall flange, Nut and Washer etc. complete as required.

Providing, Fixing, testing and commissioning of Single Lever Concealed Divertor/ Hot & Cold Mixer for Bath & Shower System along with Bath Spout with flange and Overhead Shower with revolving joint and 150 mm long shower arm with flange etc. complete as per direction-- 15 mm bib cock long body

Providing, fixing, testing and commissioning of white viterous china large flat back / half stall urinal supported by CI / MS bracket (duly painted with 2 coats of paints over a coat of primer), including CP brass waste with dome type grating, CP cast brass bottle trap with extension piece, wall flanges complete with all accessories. Kholar make Color wihte or equivalent

Providing, fixing, testing and commissioning of Black viterous china large flat back / half stall urinal supported by CI / MS bracket (duly painted with 2 coats of paints over a coat of primer), including CP brass waste with dome type grating, CP cast brass bottle trap with extension piece, wall flanges complete with all accessories. Kholar make Mat Black Color or equivalent

Providing, fixing, testing and commissioning of white vitreous china large urinal partition with concealed CI bracket, cutting and making good.

Providing, fixing, testing and commissioning of automatic flushing systems for urinal to ensure pre-flush & flushing only immediately after use, comprising of all plumbing, electronic and electrical items. CP brass flush pipe with CP brass elbow, CP brass spreader, CP wall flange, infrared photo cells, eyes electrically operated solenoid valve, step down transformer / equipment and any other item required to provide satisfactory functioning. Including necessary wall cutting / chasing and making good, as required.

Providing, fixing, testing and commissioning of sink supported by C.I./M.S. Brackets (duly painted with 2 coats of paint over a coat of primer) C.P. cast brass bottle trap with extension piece, rubber adaptor, wall flange, union, C.P. brass chainrubber plug & making good as per following details:

Stainless steel sink with drain board.(Size 900 X 600mm)

Providing, fixing, testing and commissioning of C.P. brass wall / counter mounted sink mixer with C.P. wall flange, overhead swinging spout complete as required and making good.

Providing & fixing storage type water heater of approved shade with copper container, glasswool insulation,stove enamelled M.S jacket, thermostatically controlled inner heater with pilot neon lamps, angle valve on inlet connection, 15mm dia C.P flexible connection pipe in inlet & outlet suitable for working pressure of 5 kg/sqcm complete as required-- 6 litre capacity

Providing & fixing storage type water cooler of the following capacity, I.S.I marked, stainless steel front panel, C.P brass push cock, inlet float valve with all plumbing and electrical accessories, inlet, outlet, overflow and PVC drain out connection to F.D complete as required- Cooling capacity 40 Lts./hr Having Storage capacity of 80 Lts.

Providing and fixing solid state, no touch operting, fully hygienic hand drier of approved shade with single blower, with time delay, summer & winter control, music while drying, volume ON/OFF controls including providing necessary brackets, cable from drier to Plug, Plug top key and lock etc, complete as required.

Providing & fixing C.P. brass liquid soap container with PVC rawl plug & C.P. brass screw complete as required.

Providing & fixing C.P brass deodourizer.

Providing, fixing, testing and commissioning of 15 mm dia C.P. brass bib cock with C.P. wall flange of approved quality and making good as required.

Providing, fixing, testing and commissioning of C.P Copper connection 375 mm long including nuts and washers and making connection to fixtures and fittings complete as required.

Providing and fixing 35 mm dia powder coated steel grab bar.

B. COLD WATER SUPPLY : (INTERNAL / EXTERNAL)

Providing and fixing CPVC (Chlorinated Poly Vinyl Chloride) water supply pipes with pipe as per CTS SDR 11 (operating pressure - 7 Bar @ 82 Deg C and 28 Bar @ 23 Deg C)for pipes from 1/2 Inch to 2 Inch. Schedule 80 Pipe to be used from 2-1/2 Inch to 6 Inch. Pipes shall be joined using solvent welded CPVC fittings i.e. Tees, Elbows, Couplers, Unions, Reducers, brushings etc. including transition fittings (connection between CPVC & metal pipe/GI) i.e. Brass Adaptors (both Male & Female threaded) conforming to ASTM D-2846. ASTM F441 with only CPVC solvent cement conforming to ASTM F-493. All termination points for installation of faucets shall have brass termination fittings. Installation shall be to as per Technical Manual of manufacturer of pipes & fittings.(All Terrace Looping sch80 & sdr11 for Internal Toilet)

Cost shall be inclusive of (a)Making maximum of 7.5 x 7.5 cm chase in wall and floors for the pipe, making good the same by using 1:2 cement mortar over the wire mesh and providing protection to embedded pipes and fittings (in wall chase) by wrapping two layers of 400 micron polythene sheet including proper overlaps on joints complete as required or (b) Fixing/supporting the pipes (& fittings) at wall/ceiling level supported by galvanized clamps, fastener, hangers etc, as per specification. Exposed pipes to be painted of legends with direction arrow. GI pipe sleeves suitable higher size shall be provided wherever the pipes are crossing the fire rated walls / floors slab and sealing the sleeves with glass wool in between and fire sealant compound at either end all as per Project Manager's / Consultant requirement.

3/4" dia (20 mm)

1" dia (25 mm)

1.1/4" dia (32 mm)

1.1/2: dia (40 mm)

2" dia (50 mm)

2.1/2" dia (65 mm)

3" dia (80 mm)

4" dia (100 mm)

Providing ,fixing,laying of hot water pipe insulation with tubolit closed cell polyethylene pipe insulation sleeve of approved make of 6mm thickness concealed in toilets and Shaft.

For 20mm CPVC PIPE

For 25mm CPVC PIPE

For 32mm CPVC PIPE

For 40mm CPVC PIPE

Providing & fixing brass conceald stop cock body(as per approved specification)

20 mm dia

Providing & fixing male/ female screwed end full way lever operated forged brass ball valve of brass body with forged brass hard chromeplated ball & teflon seat tested to a pressure 30 Kg / sqcm with (threaded joints) complete as required.

25 mm dia

32 mm dia

40 mm dia

50 mm dia

Providing and fixing C.I. Butterfly valve (Body : Grey Cast Iron, shaft : SS, Disc : SG Iron (nickel plated), Liner : HT - EPDM) of approved make with flange, washer, nuts & bolts and PN 10/16 pressure rating including rubber gasket & painting complete.(Plant Room + OHT Etc)

65 mm dia

80 mm dia

100 mm dia

Providing & fixing screwed ended gun metal horizontal / vertical non return valve conforming to IS 778 Class II and of PN 16 pressure rating including rubber gasket, union, etc. complete as required.(Plant Room)

50 mm dia

65 mm dia

80 mm dia

Providing & fixing dual flanged C.I. `Y' Strainer with stainless steel fine wire mesh perforated sheet basket with necessary flange/ unions nuts, bolts and washers complete as required.

80 mm dia

100 mm dia

Providing and fixing pressure reducing station for cold water supply comprising of 2 Nos Gun Metal ball valves on inlet & outlet & 1 no. globe valve for by-pass 1 No pressure reducing valve with flanged/ screwed connection, 1 No. `Y' strainer, 2 Nos Pressure gauge on inlet & outlet, and 1 No. 15 mm dia safety valve. The complete system is tested to a pressure not less than 15 Kg/Sq.cm and suitable to reduce the pressure upto 2 Kg/Sq.cm) Including necessary pipe & fittings; i.e. flanges/ unions, nuts, bolts and washers complete as required.

40 mm dia (CI Housing - PRV)

50 mm dia (CI Housing - PRV)

Providing, fixing , testing and commissioning water meter with direct reading dial in KL with all necessary fitting such as threaded pieces, unions pressure gauge, isolation cock, flanges piece for future removal, flanges / unions complete with all necessary testing charges and obtaining test certificates from municipal authorities, on following size pipe lines (1 no. strainer shall be provided at inlet & outlet and cost shall be inclusive for the same). The meter shall comply to ISO 4064 standard, feasible for class B or Class A installation.

50 mm dia (Gun metal)

65 mm dia (CI)

Providing & fixing on line turbine type flow meter with preamplifier & microprocessor based electronic flow meter mounted in plumbing plant room electrical control panel with the following features. Monitoring the total flow, Flow rate, high low arm batching and blending etc. Including electrical wiring from preamplifier to microprocessor based flow meter. Complete with all type of Plumbing & Electrical connections, accessories, wiring, conduits & supports complete with all respect. The signal from read out shall be 4-20 m.amps to be received on BAS.

80 mm dia

Making water supply connection to kitchen / laundry(Common area) equipment, appliances, coolers etc. including necessary fittings, (pipes and valves to be paid separately).

15 mm to 25 mm dia

Providing & fixing Auto Air vent for cold water supply risers, suitable for pressure not less than 15 Kg/Sq.cm.

20 mm dia

Providing and fixing 600 mm dia ductile iron (heavy duty) water tank circular cover with frame (as per EN-124) with lockable arrangement complete in all regards (Total WT of cover and frame tobe not less than 85 kg).

Providing & fixing in position 25 mm dia lawn hydrants consisting of 25 mm dia Ball valve, GI nipple and quick release coupling / threaded hose receiver complete as required.

Constructing brick masonary chamber (for housing valves, Meters etc.) of brick work with bricks of class 75 with cement mortar 1:5 (1 cement:5 fine sand) plastering internal face & (with a floating coat of neat cement) cement mortar 1:3 (1 cement: 3 fine sand and rough plaster on outer face. R.C.C top slab with medium duty D.I. manhole cover and frame of 600 mm dia (weight : 60 KG). Including excavation, dewatering, refilling, watering, ramming and removing the surplus excavated material complete as required. (All sizes are clear internal sizes).

Size 600x 600 x 600 mm deep (with 600 x 600 MD; DI cover (Wt : 45 kg))

INTERNAL DRAINAGE : SOIL, WASTE , VENT AND RAIN WATER PIPES WITH FITTINGS

Providing, fixing & testing uPVC SWR pipes confirming to IS 13592 (Type B 6KG/CM2) alongwith all required fittings like tees, bends, crosses with or without access doors jointed with approved solvent cement as per manufacturer's recommendations, fixed to walls and ceilings with clamps complete including cutting and making good the floors and walls where required complete of outer diameter.

75 mm Dia

110mm Dia

160mm Dia

200 mm Dia

Providing, fixing, jointing, testing and commissioning of UPVC pipe onfirming to IS : 13592 Type A 4kg/cm2, cut to required lengths including all necessary fittings and specials such as bends, junctions offsets, access pieces (plain or door) & vent cowl. Fixing at wall / ceiling level supported by G.I. clamps, hangers etc. duly epoxy coated. (Vent Stack )

75 mm dia

Providing and fixing sound-insulating mineral reinforced 3 layer polypropylene pipe & fitting drainage system suitable for above & below ground installation inside and outside the building structure Conforming to DIN EN 12056,DIN EN752, DIN1986-100, and DIN EN1610. Tensile strength of the pipes is accordance to DIN EN ISO 527-3. The pipe connections are leak-proof up to an internal excess water pressure of 0.5 bar.MAKE:- ASTRAL/ASHIRWAD

50mm dia

75mm dia

110 mm dia

Providing and fixing in position sound-insulating polypropylene 75 mm Multifloor traps 75MM Outlet /3 inlet Trapning design including 125 mm dia oining, embedding in concrete etc. complete rate to include making of opening in floor, marble / tiles, for fixing grating.

Providing and fixing in position sound-insulating polypropylene SWR "P" trap including providing necessary steel support and as per Specification. The hopper and trap shall be set in cement concrete mix 1:2:4 complete as required.100 mm inlet and 100 mm outlet.

Providing, fixing and testing of uPVC SWR inlet fittings / Height riser with two or three saddle inlets of 40, 50 mm size, fabricated from 110 mm outer dia uPVC pipes and fixed to uPVC traps with drip seal/m-seal/solvent cement joint complete in all respect.

Providing and fixing PVC floor drain for balcony 100 x 50mm, complete as per instructions of the Engineer in charge.

Providing and fixing Multi Floor trap 75MM Outlet /3 inlet 125mm Height , complete as per instructions of the Engineer in charge.

Providing and fixing Heavy class SS grating with Cockroach proof SS strainer of approved design including setting in floor with cement motor to match with floor finish as per architect requirement & suitable for waste and FD.

Size 125 mm dia

Providing and fixing PVC clean out plug & Fittings

For 110 mm dia pipe (Straight type/door bend )

For 150 mm dia pipe (Straight type/door bend)

Providing and fixing P.V.C. WC connector (straight or bend type) with rubber lip ring. Including 110 mm dia PVC pipe / bend of required length and proper connection.

Providing & fixing rain water `Khurras' size 450x450 mm required depth with lead flashing around the pipe with one piece lead sheet of 3 mm thick set on a layer of cold bitumen. Including Heavy duty CI/MS grating as per drawing complete as required.

Providing and fixing CI rain water head of required length with puddle flange to fix head in RCC slab including removable heavy duty dome type CI grating and CI hopper of approved design.

260 mm dia ; 100 mm outlet

400 mm dia; 150 mm outlet

Providing and fixing square mouth cast iron gully trap complete with CI grating in brick masonry chamber of standard detail with first class bricks and water tight double seal CI cover with frame of 300 x 300 mm internal size. The weight of cover and frame to be not less than 10 Kg as per standard design.

(Note : Cost shall include excavation dewatering and watering proofing of chambers as directed at site)

450 x 450 mm chamber with 150 x 150 mm size “P” trap

Constructing Grease Trap of size as mentioned below of 1200 liquid depth in brick work of class 75 with cement mortar (1:6), inside plastering 16 mm thick with cement mortar 1:3 with floating coat ofneat cement and rough plaster on outside. Including aluminium bucket as per detail to collect the grease. RCC top slab with 2 nos. 600 x 600 mm dia medium duty, double seal manhole covers with frame (weight of covers & weight of frame 75 Kg), necessary 150 mm thick foundation concrete (1:2:4).

EXTERNAL SEWAGE / STORM WATER DRAINAGE:

Providing, fixing, jointing and testing in position the following UPVC pipes confirming to IS:4985 of 6 Kg / Sq.cm for drainage system cut to required length. Pipe to be laid below ground level in trenches upto required depth including excavation in all kind of soil (hard rock), dewatering, refilling, watering, ramming and removing the surplus excavated material and making good the same complete as required. Cost shall be inclusive of providing protection to pipe all round / haunches as per specification.

110 mm dia

160mm Dia

Providing , Fixing, testing and commissioning and laying UPVC Foamcore Class-SN-8 pipes, including testing of pipes and joints etc. complete with the necessary excavation, providing and laying PCC (1:4:8), laying, refilling, compaction, dewatering, curing, retesting and disposal of any excess earth/soil from the site. The pipes shall be of following nominal bore (NB) size: External sewage water

160 mm dia

200 mm dia

250 mm dia

300 mm dia (Rate only )

Laying, jointing and testing socketed and spigotted RCC pipes (NP2 class) conforming to IS:458 collars jointed with stiff mixture of cement mortar in the proporation of 1:2 (1 cement : 2 find sand) laid to correct levels below ground in trenches upto required depth including excavation in all kind of soil (hard / soft), dewatering, refilling, watering, ramming and removing the surplus excavated material and making good the same complete as required. Cost shall be inclusive of providing protection to pipe all round / haunches as per specification. External storm water

200 mm dia

250 mm dia

300 mm dia

Designing and constructing brick masonry inspection chamber of the following sizes in brick work of class 75 in cement mortar 1:5 (1 cement:5 fine sand), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm. nominal size) embeded with frame for manhole, RCC foundation slab. 1:2:4 mix (1 cement : 2 coarse sand:4 graded stone aggregate 40 mm nominal size) both inside and outside of plastering 12 mm thick with cement motar 1:3 (1 cement : 3 coarse sand) with a floating coat of neat cement on inside face, proper water proofing to ensure no ground water seepage in the manhole, Poly propylene (conforming to ASTMD - 4101) foot rests (meeting the 224 kg load requirement as per IS 5455) at 300 mm spacing, benching and making channels with 1:2:4 cement concrete neatly finished, including necessary centering and shuttering, reinforcement, excavation, in all kind of soil, dewatering, refilling, watering, ramming and removing the surplus excavated earth, making good the same complete as required.

1. Contractor shall submit the structural design and drawings for the approval of Project Manager prior to execution.

450x 450 mm Size Depth Up to 450MM size

600 x 600 mm Size Depth Up to 900MM size

900 x 600 x Size Depth UP TO 900MM

1200 x 900 x 900 mm size

Providing & fixing Ductile Iron Manhole cover with frame:

For 600 x 600 mm MH Medium Duty (B-125) Wt - 75 kg

For 900 x 600 mm MH

1200 x900 mm, Heavy Duty (C-250), Wt : 125 kg

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 20 mm nominal size) all-round R.C.C. / DWC pipes including bed concrete as per standard design Drawing and complete as per direction of Engineer in Charge.

200 mm Dia

250 mm Dia

300 mm Dia

Construction of Catch Basin ( Road gully chamber ) of the following sizes in brick work in cement mortar 1:5 necessary 150mm thickness foundation concrete (1:4:8) inside plastering 15 mm thick with cement mortar 1:4 and rough plaster 20 mm thick on outside with a floating of neat cement. Including necessary excavation in all soil types, dewatering, refilling, watering, ramming, removing the surplus excavated material up to a lead of 100 m and making good the same complete as required. The required depth of catch basin varies from 450 to 900mm . The rate includes connections to trenches / pipes. Manhole cover will be paid separately.

450 x 450 mm clear inside dimensions ( Min. 450mm to Max.750mm )

600 x 600 mm clear inside dimensions ( Min.600mm to Max. 900mm )

Supply , Installation , testing and commissioning of FRP (Fiberglass Reinforced Polymer) Road gully chamber cover with frame design as per as per BSEN 124, IS 1726 25 ton Load in removable sections with matching frames of MS angles or making a similar size of offset in floor trimix / concrete, over open channel / chamber as per the drawings and designs and approved by architect and testing of joints complete as per direction of Engineer in Charge. Note : Min. 65% opening required in cover for entry surface water.

450mm x 450mm

600mm x 600mm

Providing and fixing 500 mm long MS hot dip galvanized PUDDLE FLANGES fabricated out of 6 mm thick MS plates of suitable size and IS:1239 heavy class pipes properly fixed in walls & top slab of tanks. The entire fittings shall be hot dipped galvanized after fabrication. Length shall be minimum 600 mm or wall thickness plus 200 mm on either side (which ever is more).

32 mm dia (screwed ends)

40 mm dia (screwed ends)

50 mm dia (flanged ends)

65 mm dia (flanged ends)

80 mm dia (flanged ends)

100 mm dia (flanged ends)

150 mm dia (flanged ends)

Providing and fixing in position the Mild Steel (MS) ‘C’ class pipes as SLEEVES each to be embedded in RCC walls / beams.

250 mm dia

200 mm dia

150 mm dia

100 mm dia

75 mm dia

50 mm dia

Drilling or Core cutting, horizontal, vertical or inclined holes in reinforced cement concrete and / or hard rock

up to 75 mm diameter for a depth / length upto 300 mm

Diameters above 125 mm upto 200 mm for a depth / length upto 300 mm

Diameters above 200 mm upto 300 mm for a depth / length upto 300 mm

Providing, laying, jointing and testing in position the following heavy class GI pipes for under ground piping conforming to IS:1239 including all necessary fittings (conforming to IS : 1879) such as elbow, coupler & tee etc. Cost shall be inclusive of excavation, dewatering, backfilling, ramming surrounding the pipe all round with minimum 150 mm thick all round compacted silver sand and providing thrust block. (Pipe shall be provided with anti crossive protective treatment Pypkote / Coatek confirming to AWWA C 203 / IS 10221 standard complete as per specification). All work complete as per specification and satisfaction of the Project Manager.

50 mm dia

80 mm dia

100MM Dia

Description of Work / Item(s)

Amount

Fees for following consultant along with their representatives at site to accomplish the job related to Building and to submit the conceptual, working and as built drawings

Fees for Vendor appointed structural consultant for entire project

Fees for Vendor appointed architect

Fees for Vendor appointed landscaping consultant

Fees for Vendor appointed MEP consultant for jobs of Electrical, HVAC, IBMS, Fire Fighting, plumbing, Structural/ Data cabling consultant etc. for services as per BOQ attached

Fees for Vendor appointed GRIHA/ IGBC consultant for 5-star rating of the Building

Fees for Vendor appointed MoEF consultant

Fees for vendor appointed remaining services other than above mentioned in remaining BOQs

Liasoning charges for below approvals, the necessary statuary charges will be paid by the department

Municipal plan approval, Completion cum occupancy certificate (JDA ) approvals

Fire & Sewarage: JMC

Electrical Inspector, Government of Rajasthan

Environmental Clearance from Pollution control Board, Rajasthan

Description of Work / Item(s)

Amount

Annual maintenance charges for following services as per the installation carried out by the bidder at the time of sign off and details of which is given in BOQ for following service s including all spares and consumables . The period will be counted after two years of Guarantee Period . ( for Two years after signing off the maintenance will be in scope of Contractor without any charges to Department ) 1.Comfort Air conditioning and ventilation 2.Elevators 3.IBMS including CCTV , Fire Detection , Fire suppression, Access control 4.Fire Hydrent and Fire Sprinkler services 4.DG Sets and HSD Tanks . 6 Transformers and HT panels , RMU , HT cables 7. All types of LT Cables and panels , Outdoor panels and all internal Electrical , Earthings jobs described in BOQ . 8 UPS and LAN Services 9.interior &Furniture 11.Civil and Plumbing services , WTP , STP , RO Water landscape 12 Solar 13 Audio & Video 14 All other items installed by bidder FOR Rajiv Gandhi Centre for IT Development and E Governance as mentioned in BoQ 1-19

1 st Year after completion of 2 years of Guarantee Period from date of signing off

2 nd Year after completion of 2 years of Guarantee Period from date of signing off

3 rd Year after completion of 2 years of Guarantee Period from date of signing off

Annual Operation charges for following services as per the installation carried out by the bidder at the time of sign off and details of which is given in BOQ for following service s. As per the final measured quantities . The period will be counted after signing off . The details of Manpower required is given in Technical specifications . The maintenance should be carried out by the maintance schedules and maintenance manual given by OEM and original manufacturar of the items installed. The details of manpower required during Operation & Maintenance is given in RFP 1.Comfort Air conditioning and ventilation 2.Elevators 3.IBMS including CCTV , Fire Detection , Fire suppression, Access control 4.Fire Hydrent and Fire Sprinkler services 4.DG Sets and HSD Tanks . 6 Transformers and HT panels , RMU , HT cables 7. All types of LT Cables and panels , Outdoor panels and all internal Electrical , Earthings jobs described in BOQ . 8 UPS and LAN Services 9.interior &Furniture 11.Civil and Plumbing services , WTP , STP , RO Water landscape 12 Solar 13 Audio & Video 14 All other items installed by bidder FOR Rajiv Gandhi Centre for IT Development and E Governance as mentioned in BoQ 1-19

1 st Year after signing off

2 nd Year after signing off

3 rd Year after signing off

4 th Year after signing off

5 th Year after signing off

Description of Work / Item(s)

Amount

Wiring of light point/Fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it's ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

Short point (up to 3 mtr.)

Medium point (up to 6 mtr.)

Long point (up to 10 mtr.)

Wiring of twin control light point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it's ISI marked (IS:3419-1988) accessories, round tiles, 2 Nos Hot Dipped Galvanized M.S Modular box of 1.2 mm thick with earth terminal,2 Nos10 A two way Modular switch, 3 pin ceiling rose / holder / 3 way connector ,Modular face plate with grid plate, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

Short point (up to 3 mtr.)

Medium point (up to 6 mtr.)

Long point (up to 10 mtr.)

Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & it's ISI marked (IS:3419-1988)accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal, 10 A modular switch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

On board

S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along with ISI marked (IS:3419-1988) accessories as required in recess including cutting the wall, covering conduit and making good the same as required. For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

S&F following sizes (dia.) of ISI marked ( IS:9537 P - II ) rigid steel conduit with wall thickness according to IS Specified along with ISI marked (IS:14768 P-II 2003) accessories in recessed using saddles, clamps, fasteners, pvc bushes, check nuts, as required including cutting jhiris in the wall and making good the same as required. For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

S&F following sizes of ISI marked ( IS:14927 P - II ) virgin material UPVC trunking along with accessories like coupler, inner, outer, elbow, square box, tee, end cap etc. on surface with screws, expansion fasteners as required. For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

75 mm x 75 mm

100 mm x 50 mm

150 mm x 50 mm

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

2 x 1.5 sq.mm

3x 1.5 sq.mm

4 x 1.5 sq.mm

2 x 2.5 sq. mm. + 1x1.5 Sqmm

3 x 2.5 sq.mm

2 x 4.0 sq.mm

3 x 4 sq. mm.

4 x 4.0 sq.mm

2 x 4.0 sq. mm. + 1 x 2.5 sq. mm.

2 x 6.0 sq.mm

1 x 10.0 sq.mm

2 x 10.0 sq.mm

4 x 10.0 sq.mm

4 x 16.0 sq.mm

Supply and laying speaker cable of IS/ISO 9001 CERTIFIED COMPANY made following size 2 core twin twisted multi stranded electrolytic grade copper conductor, overall PVC insulated and armoured cable (Blue colour) on surface/ above false ceiling including cost of GI spacers, saddles etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

Supply and laying PVC Insulated and PVC Round Sheathed Multi Core copper conductor (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing pipe / open trench / Cable tray / on surface including making connection etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

1.5 sq.mm x 3 core

1.5 sq.mm x 4 core

2.5 sq.mm x 8 core

P & F paper phenolic resin bonded laminates confirming to IS : 2036 - 1995 for boxes/ frames including making holes for switches etc, with brass screws, washers/ zinc plated nut and bolts as required. For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

3.0 mm thick

4.8 mm thick

6.4 mm thick

P & F 1.2mm thick M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

P & F 1.00mm thick M.S. Recessed concealed box, round of size 150 mm dia, depth 100 mm complete as required. All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

Single pole MCB (With B/C curve tripping Characteristics)

6 A to 32 A rating

Double pole MCB(With B/C curve tripping Characteristics)

6 A to 32 A rating

40 A rating

50/63 A rating

Triple pole MCB (With B/C curve trippingCharacteristics)

40 A rating

50/63 A rating

Four pole MCB (With B/C curve tripping Characteristics)

40 A rating

50/63 A rating

80 A rating

Providing & Fixing of 240/415 V factory fitted RCBO with overload, short-circuit and earth leakage protection with ISI marked (IS12640-2)/ conforming to IEC 61009-1, breaking capacity 10 KA, provision for pad lock, min. Electrical operation 10,000 upto 63 A rating , minimum phase termination capacity of 35sq.mm. , IP 20 contact protection with existing distribution board / sheet including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

Two pole 30 mA sensitivity

40 A rating

63 A rating

Four pole 100/300 mA sensitivity

40 A rating

63 A rating

Providing & Fixing of 240/415 V Residual current circuit breaker (RCCB) conforming to (IS:12640-1)/ IEC 61008 -1 , rated 4 KV impulse withstand voltage truly current operated and shall operate on CBCT mechanisum, provision for pad lock, min. operation 10,000 upto 63 A rating and 5000 for 100 A rating and minimum phase termination capacity of 35 sq.mm. rigid wire , IP 20 contact protection with existing distribution board / sheet including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

Two pole 30 mA sensitivity

16/25 A rating

32/40 A rating

63A rating

Four pole 100/300 mA sensitivity

63 A rating

100 A rating

Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

Metal door (single phase) IK-09 and IP-43 with Metal end box

Metal door (Three phase) Per phase isolation,Vertical IK-09 and IP-43 with Metal end box

4Way(Incomer 8,Sub Incomer2+2+2)

6Way(Incomer 8,Sub Incomer2+2+2)

8Way(Incomer 8,Sub Incomer2+2+2)

12 Way(Incomer 8,Sub Incomer2+2+2)

Providing & Fixing of Recessed/surface mounting heavy duty Flexi / Row type Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3. powder painted with reversible door (metal or Glazed) complete with 100 Amp. copper shorting link , neutral link, earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, ferrules detachable gland plate, including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

Metal door IK-09 & IP-43 with Metal end box

2 Row 28 Module(14 module per row)

3 Row 42 Module(14 module per row)

4 Row 56 Module(14 module per row)

P&F metal clad / Plastic industrial plug top & socket unit with pin and sleeve type contact on porcelain/ bakelite base in Recessed/surface mounting heavy duty Enclosure made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3. powder painted (without MCB) including making connections, testing etc.as required.For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

20 amp, 3 pin + scrapping Earth, 4 Module

32 amp, 5 pin + scrapping Earth, 8 Module

63 amp, 5 pin + scrapping Earth, 8 Module

Providing & Fixing of Recessed/surface mounting heavy duty Vertical TPN Distribution board with Metal end box with provision of incomer suitable for 3/4 pole MCCB and SP / TP MCB as outgoing ,made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3. powder painted with reversible door (for double door DB only ) complete with insulated 160 (upto 160 A Incomer) / 250 Amp. copper bus bar, neutral bars with shrouds, earth bar , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

Double door IP-43 & IK-09 with Provision of Incomer MCCB 100/ 125 A Rating with Metal end box

Providing & Fixing of modular type switch/ bell push duly ISI marked (IS :3854) with CM/L no. printed and made out of unbreakable and fire retardant vergin UV Stabilized Polycarbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating ,minimum width of switch toggle( PUSH PART ) should not less then 20mm, including all as per pre approved by Engineer in charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

10 A bell push

Providing & Fixing of modular type lockable feature socket duly made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer in charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

13 A flat pin international socket

Providing & Fixing of modular type 120 W Step Fan regulator duly ISI marked (IS 11037:1984 ) with CM/L no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer in charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

5 step fan regulator 2 Module 360 dgree rotating

Providing & Fixing of following modular accessories as per PWD specification for electrical Works, made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating , including all as per pre approved by Engineer in charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

USB Charger 1 A - 1 M with BIS mark

Providing & Fixing of following size mounting grid plates with cover plates made from fire retardent UV established high performance engineering plastic suitable for all universal metal boxes for front installation & removal direct fit type complete in all respect.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

1/2 Module

Providing & Fixing of Wiring Accessories OEM fabricated following size GI box of 1.2 mm thick with earthing terminal and adjustable floating clamp in recess/ surface suitable for modular accessories as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

1-2 Module

Supplying and fixing of power plug point with Modular accessories as per PWD specification for electrical Works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost of ISI marked modular 16 amp. Switch (IS :3854) and 6/16 amp. socket outlet (IS:1293) making connection , testing , etc. as required. For specification of Wiring accessories refer Chapter E - 07 related item & For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

SITC of Draw out type 3/4 pole door interlock Air Circuit Breaker (ACB) as conforming to IS/IEC 60947 P - 2 :2003 in existing LT panel suitable for LT installation 440 V, 50 Hz and having adjustable over load short-circuit, Instantaneous , earth fault (LSIG) with separate LED indication for each type of fault shall confirm to EMI/ EMC test , LCD/LED display, last 10 trip history, provision of ZSI, Communication, Power metering module, Thermal memory , trip free mechanisum , suitable for ambient 50 degree and utilization catagary B. In built electrical & mechanical anti pumping feature , 100% rated neutral . ACB shall have separate indication for service, test, isolation & maintenance position, Breaking capacity Icu = Ics = Icw ( 1 sec ) , U imp - 12 KV, break time not more then 25 ms. Provision for electrical & mechanical interlock between ACBs, Min.electrical operation 10000 upto 2000 A rating and 5,000 for 2500 A to 4000 A. including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution. All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

Microprocessor based release Draw out type ( Motorised charging type ) 3Pole

630/800 A Rating , 50 kA

1000 A Rating , 50 kA

Microprocessor based release Draw out type ( Motorised charging type ) 4 Pole

630/800 A Rating ,50 kA

1000 A Rating , 50 kA

1250 A Rating ,50 kA

SITC of 3 /4 pole current limiting Moulded case circuit breaker (MCCB) made of flame retardent & heat resistant material having following current rating, short circuit breaking capacity at 440/415 V, 50 Hz; O/L & S/C settings , conforming to IS/IEC 60947 P -2 :2003 with front face and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push (test) to trip, trip time less then 10 ms under s/c condition, Breaking capacity Ics = 100% Icu. U imp =8 KV, rated insulation voltage 690 V. provision for UVR , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connections etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

4 pole MCCB With Thermal Magnetic release

up to 100 Amp , 10 kA, fixed O/L & fixed S/C setting

up to 100 Amp , 25 kA, adjustable O/L & adjustable S/C setting,

125 Amp , 25 kA, adjustable O/L & adjustable S/C setting,

160 Amp , 25 kA, adjustable O/L & adjustable S/C setting,

200 Amp , 25 kA, adjustable O/L & adjustable S/C setting,

250 Amp , 25 kA, adjustable O/L & adjustable S/C setting,

250 Amp , 35 kA, adjustable O/L & adjustable S/C setting,

Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-armoured Copper cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with electrolytic grade Copper made of copper rods confirming to IS 613-1964, of purity >99.7 %, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray (with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810 For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Armoured Copper cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with electrolytic grade Copper made of copper rods confirming to IS 613-1964, of purity >99.7 %, round / flat strip armouring, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810 For additional technical parameters of product / work refer Annexure 'A' attached as per Rajasthan PWD Electrical BSR 2022

Supplying and making one end termination with Nickel plated heavy duty brass single compression gland (as per IS 12943-1990)) SIBG type consisting of Check Nut, Gland Body, Metal Washer(3 Nos.), Outer Seal Rubber Ring, Compression Nut, heavy duty aluminium lugs (as per IS 8309 -1993) duly crimped with crimping tool, PVC tape as per IS 8337-1976 of following size of PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

3.5 x 25.0 sq.mm

3.5 x 35.0 sq.mm

3.5 x 50.0 sq.mm

3.5 x 70.0 sq.mm

3.5 x 95.0 sq.mm

3.5 x 120.0 sq.mm

3.5 x 150.0 sq.mm

3.5 x 185.0 sq.mm

3.5 x 240.0 sq.mm

3.5 x 300.0 sq.mm

3.5 x 400.0 sq.mm

4 x 16.0 sq.mm

Supplying and making one end termination with Nickel plated heavy duty brass single compression gland (as per IS 12943-1990)) SIBG type consisting of Check Nut, Gland Body, Metal Washer(3 Nos.), Outer Seal Rubber Ring, Compression Nut, heavy duty Copper lugs (IS 8337- 1976) duly crimped with crimping tool, PVC tape for following size of PVC insulated & PVC sheathed/ XLPE copper conductor cable of 1100 volt grade as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

1 x 16.0 sq.mm

1 x 25.0 sq.mm

3 x 2.5 sq.mm

3 x 4.0 sq.mm

3 x 6.0 sq.mm

4 x 4.0 sq.mm

4 x 6.0 sq.mm

4 x 10.0 sq.mm

4 x 16.0 sq.mm

4 x 50.0 sq.mm

Supply, Fabricating & installing following sizes of perforated Hot dipped Galvanized iron cable tray ( Galvanized thickness not less then 50 microns) with perforation not more then 17.5% in convenient section including horizontal and vertical bends, reducers tees,cross members and other accessories as required and duly suspended from the ceiling with GI suspenders including GI bolts & nuts , fastners, supports etc. as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

100mm x 50mm x 1.6mm

150mm x 50mm x 1.6mm

225mm x 50mm x 1.6mm

300mm x 50mm x 1.6mm

450mm x 50mm x 2.0mm

600mm x 50mm x 2.0mm

750mm x 75mm x 2.0mm

Supply and fixing following size of Hot dipped Galvanized (275 GSM) floor raceways / Under floor trunking with/ without partion, including common cover, joint sleeve, cross over junction Box etc. as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

75 mm x 38 mm x 1.5 mm

100 mm x 38 mm x 1.5 mm

150 mm x 38 mm x 1.5 mm

250 mm x 38 mm x 1.5 mm

300 mm x 38 mm x 1.5 mm

Supply and fixing following Hot dipped Galvanized (275 GSM) accessories for floor raceways / Under floor trunking etc. as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Access Outlet 200 mm x 200 mm x 40-75 mm with Galvanized Lid

Access Outlet 250 mm x 250 mm x 40-75 mm with Galvanized Lid

Access Outlet 300 mm x 300 mm x 40-75 mm with Galvanized Lid

Access Outlet 350 mm x 350 mm x 40-75 mm with Galvanized Lid

Access Outlet 450 mm x 450 mm x 40-75 mm with Galvanized Lid

Access Outlet 600 mm x 600 mm x 40-75 mm with Galvanized Lid

S/F cable route marker with 10cm x 10cm x 5mm thick or 10 cm dia. G.I.plate with inscription thereon, bolted/welded to 35mm x 35mm x 5mm angle iron, 60cm long and fixing the same in ground in C C ( 1:3:6 ) as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

P / L of Double wall corrugated HDPE pipe confirming to IS : 16205 P-24, Stiffness Class 750 N, Externally corrugated and having smooth surface inside with HDPE Coupler, Elbow, Tee at required Depth below the ground for laying cable of following Nominal Outer dia. MFR Test report from NABL accrediated is to be submitted.(Excavation of Earth & Back filling with compaction is to be Paid Extra)All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

200 mm Dia.

Providing and laying Non Pressure NP-3 class R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) etc. as required. (Excavation of Earth & Back filling with compaction is to be Paid Extra). All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

250 mm dia.

300 mm dia

Providing & Laying XLPE insulated three core Armoured Aluminium cable for working voltage 11 K.V.(E) confirming IS :7098 P - 2 with H4- Grade electrolytic aluminium conductor confirming to IS: 8130 class-2 of purity >99.6 %, Insulation Screening: Extruded Semiconducting Compound followed by helically wrapped Copper Tape, round / flat strip armouring of cables , Inner / outer sheath PVC type ST-2 confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810 All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

3 core 185.0 Sq.mm

Providing & making heat shrinkable type indoor/outdoor/straight through terminations/ joint kit suitable for 11 KV / 33 KV (Earthed) cable with required components, prepration of cable ends. Type test report should be as per IS13573:2011 which covered all sequence for table 2 for termination kit and table 3 for streight through joint inclusive thermal & dynamic short circuit test, humidity test, soil fog test. Cross linking shall be done out side factory with E- beam/ peroxide technology. Extrusion process shall be in house OEM within same vicinity. including testing etc. as required of following sizes. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

11 KV End Termination Kit Indoor type

3 core 120/150/185 Sq.mm

11 KV End Termination Kit Outdoor type

3 core 120/150/185 Sq.mm

Plate Earthing as per IS:3043 with Hot dipped G.I. Earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. G.I. 'B' class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Plate Earthing as per IS:3043 with copper Earth plate of purity >95% of size 600mm x 600mm x 3.0mm by embodying 3 mtr. below the ground level with 20 mm dia. G.I. 'B' class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Supply & Laying following size earth strip in horizontal or vertical run in surface by means of Earth strip DMC Insulator including riveting/ soldering/ welding, Jointing shall be done by overlapping and with 2 set of Brass (for Cu strip) / GI (for GI Strip) nut bolt & spring washer spaced at 50cm making connection etc. as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

25mm x 3mm copper strip

50mm x 6mm copper strip

25mm x 3mm G.I. ( Hot Dipped ) Strip

25mm x 6mm G.I. ( Hot Dipped ) Strip

32mm x6mm G.I. ( Hot Dipped ) Strip

50mm x 6mm G.I. ( Hot Dipped ) Strip

Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with GI/Cu purity purity >95% thimble etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

8 SWG tinned copper Wire

8 SWG G.I. ( Hot Dipped ) Wire

16 Sq.mm Copper coated steel stranded conductor (Wt. 130 Kg/Km

25 Sq.mm Copper coated steel stranded conductor ( Wt. 200Kg/Km

S & F of Earth Bar with Disconnecting link Made out from 50 mm x 6 mm copper purity purity >95% /GI strip pre fitted on epoxy powder coated metal base mounted on hexagonal SMC Insulators of following Size.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annex ure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

400 mm , 6 Way Copper

600 mm , 10 Way Copper

400 mm , 6 Way GI

600 mm , 10 Way GI

P & F Lightning counter - To count no of lightning strike & it can record the date and time of the lightning incident also tested as per IEC 62561-6. the test report accredited by third party accreditation body like VDE/ILAC/ DAkkS/ UL/ NABL is to be submitted.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annex ure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Providing & Fixing of 400 mm Sweep BLDC technology Oscillating type Wall mounting / Pedestal type fans with Three speed, ON and OFF position, Double Wall bearing with front and back 120 or more ribs guard; Three no. blades, noise level should be <= 75 dB, including fixing with anchor bolts, making connection testing etc. as required. ( With Remote ) All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Wall mounting type with Service value 2.0 CMM /W, Min. Air Delivery 71 CMM

Providing & Fixing of BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 )

Providing & Fixing of Heavy duty capacitor start, copper wound Double ball bearing 900/1400 RPM single phase Exhaust fan conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

300 mm sweep(900/1400 RPM)

600 mm sweep(700 / 900 RPM)

Providing & Fixing of Vertical(BEE 5 star rated) / Horizontal( BEE 3 star rated) storage water heater with outer casing made of Engineering Plastic sheet (Upto 25 Ltr) / Metal rust proof Body (35 & 50 Ltr), Glass - line / Titanium Enamel coated Pressure Pump Compatible 8 bar pressure Inner tank, Glass Line Coated , mineral filled heating element, stem type, snap action adjustable thermostat , Dual indicating lamps Injected PUF insulation, Multi Function Valve etc. as required held in position with 2/4 no. 10/12 mm anchor Fastener, duly wired with 3 core 2.5/4.0 Sqmm PVC insulated & sheathed copper conductor and 16 A/25A three pin plug top with Portable Residual Current Device ( PRCD ) , including making inlet, outlet Flexible alloy connection, testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminium housing with in built driver , System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

1170mm(+/-10%) LED batten with min. lumen output 2200 lm

570mm (+/-10%) batten with min. lumen output 1000 lm

Providing & Fixing of IP-20 LED Recessed / Surface Mounted, Round / Sqaure SMD Mid Power LED Downlight with power coated die-cast aluminum housing with UV Stabilized non yellowish Diffuser with BIS complience 2.5 KV surge protected Isolated driver, with Short & Open circuit protection, having efficiency > 85% . System Lumen efficacy of ≥ 110 lm / watt, THD < 10 % , Pf.≥0.95, CRI >80, life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.

OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Recessed Mounting

Minimum lumen output 330 lm

Minimum lumen output 650 lm

Minimum lumen output 1300 lm

Minimum lumen output 1600 lm

Minimum lumen output 1950 lm

Minimum lumen output 2400 lm

Providing & Fixing of IP20, 2'x2' LED Surface/ Recessed mounting Mid power SMD type LED Light fixture not less than 50mm housing depth made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non -yellowish diffuser for uniform light distribution. High efficiency with 4 KV internal/external surge protection BIS certified isolated driver having efficiency > 85% , with Short & Open circuit protection (Integral with light fixture). System lumen efficacy of ≥ 120 lm/Watt ,THD < 10 % , p.f.≥0.95,CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.

OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Recessed Mounting

Minimum lumen output 3600 lm

Minimum lumen output 4200 lm

Providing & Fixing of IP65 IK08 rated Integrated SMD Mid power LED bulk head type light fixture made from Pressure Die Cast AL housing suitable with integral driver, system lumen efficacy ≥100 lm/Watt output , THD < 10% ,p.f.≥0.95,CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. surge protection 4 KV. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Minimum lumen output 1000 lm

Supply and erection of Galvanized Iron pole with galvanizing done in single dipping (Average coating thickness Minimum 65 Microns) continuously tapered poles having Octagonal / Circular cross-sections designed to withstand the maximum wind speed as per IS 875, The pole shaft shall be made from sheet steel (HT Steel Conforming to grade S355JO) and confirming to BSEN 10025 and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding. The welding of pole shaft shall be done by Submerged Arc Welding (SAW) process. pole shafts shall be provided with the rigid flange plate of suitable thickness (Fe 410 conforming to IS 226 / IS 2062) with provision for fixing 4 no. foundation bolts, This base plate shall be fillet welded to the pole shaft at two locations i.e. from inside and outside.The octagonal Poles shall have lockable door of approximate 500 mm length at the elevation of 500 mm from the Base plate with bakelite sheet having 6A SP MCB and 16 sqmm stud type connector ( 4 nos) inside the pole at door opening for cable connection of following length and dimension as per table P-01 with base plate and foundation bolt on the Existing cement concrete foundation.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Poles with Octagonal Cross Section

Supply and Fixing of Pole OEM fabricated hot dipped galvanised M.S. Overhang (48.3 X 3.25 mm) with cap (400 x 88.9 / 114.3 x 3.25 mm) over the existing poles. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Single arm overhang

Supply installation testing & Commissioning of high mast lighting system (as per PLG 07 of ILP UK techinical report no 7 of ILE UK /IS:875 Part-1 – 2015//BSEN10025/and IS:2062 )consisting of totally hot dip galvanised by piecewise single dipped method high mast, lantern carriage suitable for up to 12 nos luminaries with welded arm (excluding luminares), mast head frame assembly with full cover, including 1 No. LED 15 Watts aviation obstruction lights, double drum type self sustaining winch, integral power tool accesible from door with padlocking arrangement (winch motor with control circuit) hot dipped galvanised heavy duty pipe lightening finial, Stainless steel 6 mm dia. wire ropes (AISI 316, 7 / 19 costruction 3 no. rope for lantern carrage & 2 no. rope for winch assembly ) foundation bolt, torque limiter,EPR insulated PCP sheathed 5 core x 2.5 Sq.mm trailing cable, including outdoor type control panel for auto on / off, reverse / forward motor operation. The mast is constructed from mild steel plates (as per IS 5986 Gr. 510 ) cut and folded to form a polygonal section, telescopic jointed and welding as per BS 5135.etc. as required on Existing Foundation. ( See table P - 03 for specs.) OEM Must have Type test certificate for wind tunnel test . All as per pre approved by Engineer in charge. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

16.0 Mtr HM (in 2 section) suitable for 9 No. Luminaries

Providing and Laying RCC Foundation for Octagonal / Conical Street Light poles, High mast Poles as per Drawing attach at Table P-4 with Following Procedure & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

A) Excavation of Pit for Foundation Size upto required depth from Ground level

B) Dressing of Pit and Dry stone pitching 200 mm thick including supply of stones and preparing surface complete.

C) Providing and laying in position cement concrete of M-10 grade of 75 mm thickness

D) Reinforcement for R.C.C. work with TMT bars including straightening, cutting, bending, placing in position and binding all complete.

E) Centring and shuttering including strutting , propping etc. and removal of form work for Footing and Pedestal

F) Providing & Fixing of 2 no. Required Size PLB HDPE Pipe & Foundation Bolt with template as per OEM Recommendations.

G) Providing and Laying Reinforce cement Concrete of M-25 grade in Footing and Pedestal including Curing the foundation for 7 days.

H) Providing and Fixing Nosing Angle 40 mm x 40 mm x 6mm with 2 no. 100 mm long, 10 mm dia. Lugs on each face.

Pole Foundation for Octagonal pole from 3 Mtr. To 6 Mtr.

Providing & Fixing of IP-65 Protected LED aviation obstruction light luminaire comprising of die cast aluminium alloy housingwith Polycarbonate enclosure having more than 200 No's Low Power LED's having minimum power consumption 15 watts complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

aviation obstruction LED light luminaire Min. 15 Watts

Providing & Fixing of IK08 IP65 protected Top/Bottom mounted LED Post top Luminarie made of single piece construction powder coated die cast alluminium housing with UV stabalized Clear / frosted Polycarbonate diffuser and Aluminium anodised with sand blast reflector. The System level Luminous efficacy ≥ 100 Lumen/W. SMD LEDs is to be used, System CRI>70, CCT: 3000/4000/6500 K. The integral electronic driver must be potted & has a unique BIS R number must be potted & has a unique BIS R number constant current and Internal/external surge protection device of min. 4KV(L-N) and efficiency > 85%, PF>0.9, THD<10% and input Voltage range of 140-270V AC at 50Hz. System life of 50000 Burning hours with 70% of Initial Lumens maintained . Driver current <750mA. Fixture must be in compliance with BIS Standards and Trade mark Certificate complete in all respect.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Minimum lumen output 3000 lm Post top Luminarie

Providing & Fixing of IK08 IP-66 protected high power LED flood light system with single piece Pressure diecast aluminium housing, toughened glass diffuser with suitable lenses on LED to achieve various beam angles, of high power LED of 3 to 5 watt each . Integrated potted driver as a unique BIS R number having efficiency more than 85 % and in compliance to BIS certified and Trade mark certificate. The System level Luminaire efficacy >=125 lm/ wt. LED driver Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety .Power Factor >0.95 , THD(I) <10% , driver current <=750mA. driver should be Phase to phase protection of 440 V for 4 Hrs. Electrical Connector , Surge Protection Min >=4KV internal and 10KV external but inside driver compartment, System life of 50000 Burning hours with 70% of Initial Lumens maintained, CRI>70 and CCT 5700K ±355K. Manufactures Word Mark/Name Engraved/Embossing/Screen printing on die cast housing to allow traceability/authenticity. Fixture shall be IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

High Power LED Flood Light Minimum lumen output 10000 lm

Providing & Fixing of IK08, IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on housing with UV stabilized PC (UV stablization report submitted for UV cover ) /Toughened Glass cover and secondary lens on each LED & should be SMD type of 3 to 5 watt each . The System efficacy >=125 lm/ wt and potted driver & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety , Power Factor >0.95 driver Efficiency >85% ,THD(I) <10% Humidity 10% to 90% RH Working Temp -5C to 45C . driver current <750mA. The luminaire shall be BIS certified and Trade mark certified. Life Expectancy Equal or more than 50000 burning hrs with Minimum 70% lumen maintened , CRI >70 and CCT 5700K +355K. Surge protection shall be min ≥ 4 KV internal and min 10 KV external inside driver compartment. driver should be Phase to phase protection of 440 V for 4 Hrs. Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

LED Street Light fixture with Minimum lumen output 7500 lm

Providing & Fixing of IK10 IP65 protected 600 mm height LED Bollard Luminarie with base plate made of powder coated die cast alluminium housing with UV stabalized PC diffuser. The System level Luminous efficacy ≥ 90 Lumen/W. SMD LEDs is to be used, System CRI>70, CCT: 3000/4000/6500 K. The integral electronic driver must be potted & has a unique BIS R number must be potted & has a unique BIS R number constant current and Internal/external surge protection device of min. 4KV(L-N) and efficiency > 85%, PF>0.9, THD<20% and input Voltage range of 90-270V AC at 50Hz. System life of 30000 Burning hours with 70% of Initial Lumens maintained Light output in Cool white or Warm White Colour as per engineers choice. driver current <750mA. Fixture must be in compliance with BIS Standards and Trade mark Certificate complete in all respect.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Minimum lumen output 980 lm Bollard

Providing and fixing of IP 65 protected Polycarbonate / Polysterene fuse box moulded with inside knock outs of following size with hinged cover, transparent window, PU gasket, locking arrangement, duly holded with 2 nos. pole clamps of 20 mm x 3 mm flat with nut and bolts, The box shall be provided with Din rail, 4 / 8 way 10.0 / 16.0 sq.mm heavy duty connector, earth terminal, complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

125 mm X 200 mm X 122 mm

Providing & Fixing of IP - 65 protected impact resistant polycarbonate / Polysterene enclosures with knock out for cable entry/out including fixing with nut, bolt, fatner etc as required complete in all respect of following sizes.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

SITC of following capacity IK10 Sandwich Type Rising Mains / Bus Duct Confirming to IEC 61439 part 1 & part 6 standard & IS 8623 P-II and Manufactured in India for use on 3 phase 4 wire , 50% internal earth , 415 volts, 50Hz A.C. supply , class F insulation, rated insulation voltage 1000V, impulse withstand voltage 12 KV, min. seismic zone 4 as per IS1892, with IP-54 / IP-66 (With Canopy) enclosure made of 1.6mm thick sheet steel duly powder coated in convenient sections complete with 4 Nos aluminium (with 6101 or 63401 grade) bus bars, necessary joints & expansion joints, fire barrier at each floor, provision of tapping at every metre, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system including making opening in RCC / Brick Masonary and repairing the same etc. as required. Type Tests reports like (i) Short Circuit Test (ii) Degree of Protection (iii) Temperature rise test of Rising main in CPRI / UL / ASTA accrediated lab will be submitted by OEM.

Routine test as per OEM's QAP in It's own Manufacturing facility in India shall be witnessed by department Engineer virtually / Physically. Complete Installation of Rising Mains shall be Vetted by Manufacturer before Comissioning. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Sandwich Type Bus Rising Main

630 amps 40 KA SC for 1 sec

Sandwich Type Bus Duct

1000 Amps 50kA SC for 1 sec

1250 Amps 65kA SC for 1 sec

1600 Amps 80kA SC for 1 sec

Out Door Bus Duct IP66 with Canopy

1000 Amps 50kA SC for 1 sec

1600 Amps 80kA SC for 1 sec

SITC of Bus Rising Main OEM manufactured following capacity End Feed Unit Confirming to ANSI C37.23 standard & IS 8623 P-II suitable for Sandwich / Compact Air Insulated type for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure duly powder coated with provision of MCCB/ACB (but without MCCB/ACB), Interlocking feature complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

For 630 Amp. (Without MCCB)

SITC of Bus Rising Main OEM manufactured following capacity Plug in / Tap off Box suitable for Sandwich / Compact Air Insulated type bus bar trunking Confirming to ANSI C37.23 standard & IS 8623 P-II & IEC-60947-2-2000 for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure duly powder coated with provision of MCB/MCCB / ACB (but without MCB/MCCB/ACB) with Interlocking complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Plug in Box suitable for Sandwich Type Bus rising Main

100/125 amps (Suitable for MCCB) without MCCB

160/200/250 amps (Suitable for MCCB) without MCCB

400 amps (Suitable for MCCB) without MCCB

SITC of Bus Rising Main OEM manufactured Tinned copper flexible joint with enclosure of following capacity with Transformer / DG / Panel as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

1000 Amp. Rating

SITC of HT metering cubical panel as approved By DISCOMs fabricated out of 18 SWG CRCA sheet steel in two compartment & MS angle of size 60mmX 6mm having provision for Following: (i)Provision for fixing Trivector / Import - Export Meter (To be supplied by DISCOMs) (ii)Provision for fixing of combined CT PT Set with Copper strip for Connection (To be supplied by DISCOMs), (iii)Test terminal Block, (iv) 6mm thick Bakelite sheet on all sides, (V) 3/6 corex 1.5 / 2.5 Sq.mm copper cable for interconnections, etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

SITC of Radiator Cooled and Turbo charged Silent DG Set (As per latest CPCB emission norms) having specifications as per A, B, C, D, E, F,G,H & I

A) 1500 RPM Diesel Engine conforming to BS:649/5514 of suitable BHP (up to 82.5 kVA 6 cylinder or Below required, 125 kVA & Above ratings 6 cylinder or above required ) capable of taking 10% over loading for one hour after 12 hours of continuous operation., Dry exhaust mainfold with Hospital grade silencer and catalytic convertor(isolated from main DG chamber), up to 3 M exhaust piping (with LRB insulation & Alum. cladding ) as required . B) AC Brush less SPDP Alternator conform to BS 5000 (part 99) or IS/IEC 60034-1. . Alternator shall be self regulated with standard Alternator Protection( Over voltage , over speed & under voltage, under speed warning & shutdown).Engine & Alternator mounted on a common base Frame & coupled through a flexible coupling or close coupled C) CPCB / ARAI approved Standard canopy with Weatherproof, powdercoated Accoustic enclosure for DG set for sound attenuation fabricated from 1.6 mm CRCA sheet steel (structure) with sidewall fabricated from 1.6 mm CRCA sheet & filled with glasswool (96Kg/m3) / Foam. as per IS8183 the doors of 28/40/50/85mm thick as perrating and fabricated from 1.6mm CRCA sheet packed with accoustic material, All doors/opening are sealed with neoprene /EPDNgaskets. The DG Set has Inbuilt / External in fuel tank to run 6 to 8 Hrs as per OEM standard, with protection and tripping of DG set against temperature of more than 50 degree centigrade.

D) Electronic / Mechanical governor, Manual & electric Start ,Batteries with battry charger, Engine instruments panel,AVM pads All controls for operation of DG set are from outside the enclosure with DG control panel having Microprocessor based Genset monitoring like Running Hour, RPM, Low Lube Oil tripping & control system, Panel mounted MCCB/ACB of suitable rating, Ammeter, Voltmeter, PF meter, frequency meter, KWH meter,digital fuel display meter, Ind.lamps etc. mounted inside enclosure , visible and accessible from outside. The enclosure should be suitable for following capacity DG sets and alternator. Noise level shall be less than 75 dB at a distance of 1 Mtrs. duly certified by authorised agency etc. complete in all respect of following capacity : E) (i) Accoustic glass wool wall thickness should not be less then 40mm and not less then 20mm PU foam upto rating 100 KVA. (ii).Accoustic glass wool wall thickness should not be less then 65mm and not less then 50mm PU foam upto rating 250 KVA. (iii)Accoustic glass wool wall thickness should not be less then 100mm for rating above 250 KVA. F) First filling of the fuel tank shall be done by contractor and the prevailing fuel cost at that time shall be reimbursed to the contactor by department.

G) Servicing Contract of DG Set from OEM's Authorised Service Dealer as per OEM guidelines during the DLP period shall be done by contractor including all consumables, actual charges shall be reimbursed to the contractor by End User Department. H) Manufacturer / OEM must have its authorized service dealer in Rajasthan. Which can provide service within 6 Hours of compalint registration. I) DG set will be offered for Inspection and Testing at Manufacturer's Works in presence of Departmental Engineers. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 . j) Suitable for synchronization

750 KVA at 0.8 pf 415V 50Hz 3-ǿ

250 KVA at 0.8 pf 415V 50Hz 3-ǿ

160 KVA at 0.8 pf 415V 50Hz 3-ǿ

Providing, Fixing, Jointing, Testing & Commissioning of Medium duty MS B class pipes conforming to IS 3589 / 1239 part-I for DG Exhaust applications (beyond 1.5 Mtr. length) including cutting, welding etc & fittings like elbows,flanges, tapers, reducer, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps, hanger and nuts bolts . including the cost of thermal insulation with 50 mm thick layers of LRB rock wool as per IS : 8183-1993 (64 kg/m3 density) & 26 SWG aluminium sheet claddings etc complete as required complete in all respect. (Cost of Steel Structure for Exhaust pipe will be paid Extra). All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

150 mm dia

250 mm Dia.

Supply, installation and testing of metal flexible coupling (bellow) of following dia required for horizontal length more than 3 mtr.as per standard of guide line of D.G. set company complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

250 mm Dia.

Supply & fabrication steel structure with MS channel / angle / joist / ISMB / sheet etc. including welding, rivetting, cutting, nut & bolt , one coat of primer & two coat of enamel paint etc. as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

NON BSR ITEM

P & F of Early streamer Emission type lightning arrester on GI mast with air terminal configured as spheroid which is comprised of separate electrically isolated 4 panels surrounding an earthed central finial, the terminal shall be tested by CPRI for impulse current of 45 kA ( 8 / 20 Sec ) with 5 positive & 5 negative impulse, the arrester having following protection radius at level 1 Device shall comply NFC 17-102 and UNE 21186 standards. The device shall be mounted at least 4-5 meters high clear to highest point on the roof top with proper mounting arrangement. ESE for radius 50 mtr for level 1 protection

ESE for radius 50-68 mtr for level 1 protection

Single core 70 Sqmm Copper Armd. Cable downcondctor

P & F Lightning counter - To count no of lightning strike & it can record the date and time of the lightning incident also tested as per IEC 62561-6. the test report accredited by third party accreditation body like VDE/ILAC/ DAkkS/ UL/ NABL is to be submitted.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annex ure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Supplying and erecting danger notice board for medium voltage installation to be erected as per I.S. The board should be 150 x 150 mm.

Supplying and erecting danger notice board for high voltage installation to be erected as per I.S.

Supplying and erecting printed instruction chart both in English & REGIONAL LANGUAGE & duly framed out on glass for treatment of person suffering from Electric shock.

Supplying pair of rubber hand gloves suitable for working on 11 KV/22 KV supply.

Supplying and fixing Standard First aid box with all the Standard contents.

SITC OF WATER Proof Boxes fro out door lighting IP-68

Cable junction boxex IP67 1.5 MM2-4sqmm ,CU-3 wth terminal cable entry knockouts

Cable junction boxex IP67 2.5 MM2-6sqmm ,CU-3 wth terminal cable entry knockouts

Cable junction boxex IP67 4.0 MM2-10sqmm ,CU-3 wth terminal cable entry knockouts

Supplying,installation,testing and commissioning of Passive Infrared(PIR) technology based occupancy sensor having high preformance, non regulating programmable type, suitable for connected load upto 10Amp , for mounting height up to 2.8 mtr and for 5 m diameter coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required

Supply , Installation , Testing and commissioning of floor box/ pop up boxes according to EN60670-1/EN 60670-23 for installation either as joint box / or 5/15 amp switch / Socket/ cat6/ cat6A IO points as per direction of engineer incharge.( Make: Legrand or equivalent)

10 modules floor pop up box

16 Module Floor pop up Box

SITC of wall/ free standing floor mounted dust and vermin proof compartmentalised cubical panel as per attached SLD and GA drawing and as per TTA & PTA specification for electrical Works, made out of CRCA sheet . Other parameters required as per point (a) ,(b), (c)below:-

(a)Thickness of sheet shall not be less than 1.6 mm up to 600 mm length / width of any compartment and be of 2.0 mm above 600 mm. Load bearing structure shall be of 2.0 mm thick sheet supported by base M.S. channel if required . Side walls and cable alley compartments having bolted type doors with / without detachable extension type structure

(b)panel shall be duly treated for derusting in 7 tank process with dephosphating and with powder coating of minimum 70 microns on both side of panel in desired shade The panel having PU/ Neoprene rubber gasket of not less than 3mm thickness ,required hardware, separate detachable gland plate M.S. base channel (min75mm) , hinged door with locking arrangement for equipment/switchgear

[c) Interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 125 amp ) and by solid bus bar (>125 amp ) . All joints / interconnections of copper bus bar shall be dully tinned . Clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar Bus bar is insulated by Heat Shrinkable sleeves . Earth and Neutral bus bar shall be half of the size of phase bus bar.

MAIN I/C PANEL @ SUBSTATION PANEL ROOM TTA PANEL AS PAR IEC-61439

200kVAR APFC PANEL ADMIN BLOCK TTA PANEL AS PAR IEC-61439

GROUND FIRST FLOOR LIGHT AND POWER PANEL TTA PANEL AS PAR IEC-61439

BASEMENT FLOOR-1 COMMON AREA PANEL TTA PANEL AS PAR IEC-61439

TYPICAL FLOOR LIGHT & POWER FLOOR PANEL ROOM TTA PANEL AS PAR IEC-61439

MAIN UPS LT PANEL TTA PANEL AS PAR IEC-61439

UPS FLOOR PANEL TYPICAL FLOOR TTA PANEL AS PAR IEC-61439

SUB UPS PANEL TTA PANEL AS PAR IEC-61439

PLUMBING PANEL TTA PANEL AS PAR IEC-61439

TERRACE FLOOR COMMON AREA FLOOR PANEL TTA PANEL AS PAR IEC-61439

PARKING AREA PANEL AT SUB STATION TTA PANEL AS PAR IEC-61439

TYPICAL DRAWING FEEDER PANEL TOTAL 3 NOS FEEDER PILLAR (FOR EXTERNAL LIGHT ROAD LIGHT AND AREA LIGHT) TTA PANEL AS PAR IEC-61439

FIRE PROTECTION PUMP PANEL TTA PANEL AS PAR IEC-61439

Description of Work / Item(s)

Amount

Supply Installation testing and commissioning of HT VCB Panel 11KV 1250A 26.3KA having 1 Incomer VCB and 2 Outgoings VCB as per attached Specification

SITC of 11kV 630 Amps 21KA for 3 Sec. SF6 insulated, outdoor duty (IP54) , Extensible / Non extensible type Ring main unit (RMU) manually operated in combination of VCB modules and Load Break switch consisting of Copper busbar in SF6 insulated 304 (Non-Ferrite Non-Magnetic Grade) stainless steel enclosure of thickness 2.5mm with manometer. The HV switchgear and control gear should be confirming to IEC-62271-100, IEC-62271-200-2003 & IEC-60694-1996. The RMU should be internal arc tested for 21KA for 1Second with IAC-AFL classification for gas tank. Vacum Interrupter of VCB should be RMU Manufacturer’s own make. Each feeder of RMU should have voltage presence indicator. . and compring of followings:- 1 no. microprocessor based Self powered numerical relay with over Current/ earth fault & short circuit protection with each VCB feeder. - 3 Nos. Protection CT shall be of Burden 2.5VA, ratio 50/1A, Class of Accuracy class 5P10 for O/C and E/F protection for each VCB.- 1 No. Manometer for each tank,- 1 nos. Fault Passage indicator,-Right angle boots for all the feeder Modules All the type test certificates as per IEC from Third party NABL / CPRI / ERDA accrediated lab to be submitted. (Cost of RCC Foundation / Steel Structure to be paid Extra) All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan Rajasthan PWD Electrical BSR 2022

Extensible 3 way RMU with 1 no. VCB & 2 No. Load Break Switch

Supply installation testing & Commissioning of Copper wound distribution Transformer of following rating and % Impedance, 11/0.433KV Delta-Star Connected, Vector Group Dyn 11, ONAN Cooled losses as per IS 1180 part I 2014 (Fourth Revision) Level-2, with boltless core design including standard accessories like conservator with prismatic oil level gauge , silica gel breather, Bucholz relay, pressed steel radiator fins, Radiator Valve(above 800 Kva) Suitable size HT cable box, LT cable box with Busbar connection for outgoing cables, On -LTC (+/- 2.5%, +/- 5% to - 7.5% ), temperature rise of 40 degree C in oil / 45 degree C in winding , drain valve, Air release device, Dial type Oil & Winding Temperature gauge with alarm & trip contacts, first filling of transformer oil as per IS :335-1953 , Epoxy primer and PU based paint as Top coat, Unidirectional rollers for rating upto 800 kva & bi- directionalabove 800 Kva rollers with locking arrangement etc. as required. The Transformer shall be subjected to routine factory tests (as per IS:2026 and IS:1180) including Temperature rise test in OEM's own lab shall be witnessed by Department engineer Physically.

Transformer shall be tested from CTL of discom before charging of transformer & complete installaion must be certified from Electrical Inspectorate office as per Indian Electricity rule, (CTL testing charges and Electrical Inspection charges shall be reimbursed by the department to the contractor)Following tests shall be carried out on each transformer at site by OEM enginer in presence of department authorised representative:- a) Ratio test on each tapping.b) Resistance of windings at principal and all tapings.c) Insulation resistance of the winding between HV to earth / HV to LV / LV to earth.d) Vector group test.e) Magnetic Balance test. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

800 KVA with % Impedance 4.5

Description of Work / Item(s)

Amount

SITC of Solar Grid Tied Power Plant Mono crystalline Based of following KW AC output complete in all espect including structure , solar panels , grid tied inverter , connecting AC and DC cables , AC and DC protection ,DC and AC Interconnectiong cables ,DC and AC Distribution Box , Solar meter , MCCB for protection , Pressure pupms with CPVC pipes for cleaning as per Technical specifications and makes enclosed in RFP .

50 kw AC Output (Terrace)

25 kw AC Output ( Terrace )

Description of Work / Item(s)

Amount

Supply Installation testing and commissioning of of EN/IEC62040-1, EN/IEC 62040-2, EN/IEC 62040-3, CE/UE APPROVED STANDARD , Online UPS with 15 mins Battery Backup with Digital Signal Technology with inbuilt/Separate Isolation Transformer , 3 level IGBT ,DSP Controlled Based design as per attachted specifictations Complete as required as per specification enlosed of following capacity as per follwoing specification .

Supply and Installation of 90KVA (3/3) Online UPS with 15 mins Battery Bank with MS Rack and Batteries Interlinks

Description of Work / Item(s)

Amount

Supplying, Installation, Testing & Commissioning of Electrical Driven fire fighting duty pump as per TAC and IS 12469-1988., Factory assembled in Pump make OEM for Sprinkler / Hydrant applications suitable for automatic operation and consisting of following details given as A, B, C, D, E, F, G and H.

(A) End Suction / Horizontal Axially split casing volute type Single / Multi stage Centrifugal pump complete for delivery of below mentioned discharge and Head (B) Material of construction : Pump Casing - Cast Iron, Impellor - Bronze, Shaft - SS 410, Packing - Mechanical Seal (C)Pump shall be capable of furnishing not less than 150 % of rated capacity at a head not less than 65 % of the rated head. The shut off head shall not exceed 120 % of rated head (D) Squirrel cage induction motor (IE-3 Class) suitable for 3 phase, 415 V, 50 HZ, Ac supply , Class -F Insulation, Synchronous speed 2900 / 1500 RPM, T.E.F.C confirming to IP:55 , of required HP suitable for the above pump ,along with flexible (Love Joy type) coupling , coupling guard complete in all respect .

( E) Common bed plate fabricated from mild steel channel for installation of pump and Motor including anti vibration pads. (F) The Hydrostatic tests (2 times of design operating head or 1.5 times the shut off head whichever is higher) and performance tests (to determine developed head, Pump BHP and efficiency v/s Flow) of pumps along with trip test shall be carried out at manufacturer’s works in Physical presence of Department’s representatives. (G) Physical & Chemical Test reports of i) Pump casing (ii) Impeller (iii) Shaft (iv) Shaft sleeve and Dynamic Balance certificate is to be submitted by OEM (H)Suitable size Reinforced cement concrete (M-30) foundation with foundation bolt, Nozing Angle of size 40mm x40mm x5 mm ( Cost of RCC Foundation to be paid Extra ). All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

2850 LPM suitable for 70 Mtr Head Horizontal Axially split casing volute type Two stage, 1500 RPM

Supplying, Installation, Testing & Commissioning of Diesel Engine Driven fire fighting duty pump as per TAC and IS 12469-1988., Factory assembled in Pump make OEM for Sprinkler / Hydrant applications suitable for automatic operation and consisting of following details given as A, B, C, D, E, F, G and H.

(A) End Suction / Horizontal Axially split casing volute type Single / Multi stage Centrifugal pump complete for delivery of below mentioned discharge and Head (B) Material of construction : Pump Casing - Cast Iron, Impellor - Bronze, Shaft - SS 410, Packing - Mechanical Seal (C)Pump shall be capable of furnishing not less than 150 % of rated capacity at a head not less than 65 % of the rated head. The shut off head shall not exceed 120 % of rated head

(D) Heat Exchanger cooled Diesel Engine as per NFPA 20 developing suitable BHP for the below mentioned discharge at 1500 / 1800 RPM, flexible coupling and coupling guard with the Pump, common bed plate for mounting of the Engine and Pump,Antivibration damping arrangement by cushy foot, Diesel Engine starting Panel for starting of the engine automatically if the Normal electrical supply fails with a unit of battery bank of 12/24v,180 Ah, Lead Acid Battery with Boost / Trickle charger as required for operation of Diesel engine, Exhaust Pipe of suitable diameter upto 10 M length (with LRB insulation & Alum. Cladding), with muffler, Diesel tank of 300 Lts capacity (made out from 2 mm thick MS sheet with filling Cap) with drain cock, Diesel level Indicator, Suitable MS angle iron stand for placing tank, first Filling of Diesel tank.

(F) The Hydrostatic tests (2 times of design operating head or 1.5 times the shut off head whichever is higher) and performance tests (to determine developed head, Pump BHP and efficiency v/s Flow) of pumps along with trip test shall be carried out at manufacturer’s works in Physical presence of Department’s representatives. (G) Physical & Chemical Test reports of i) Pump casing (ii) Impeller (iii) Shaft (iv) Shaft sleeve and Dynamic Balance certificate is to be submitted by OEM (H) Pump to be placed on Suitable size Existing Reinforced cement concrete (M-30) foundation with foundation bolt, Nozing Angle of size 40mm x40mm x5 mm ( Cost of RCC Foundation to be paid Extra ). All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

2850 LPM suitable for 70 Mtr Head Horizontal Axially split casing volute type Two stage, 1500 RPM

Supplying, Installation, Testing & Commissioning of Electrical Driven fire fighting duty Jockey pump as per TAC and IS 12469-1988., Factory assembled in Pump make OEM suitable for automatic operation and consisting of following details given as A, B, C, D, E,F and G

(A) Horizontal End suction Single / Multi Stage Centrifugal Back pull type pump complete for delivery of below mentioned discharge and Head (B) Material of construction : Pump Casing - Cast Iron, Impellor - Bronze, Shaft - SS 410, Packing - Mechanical Seal (C) Squirrel cage induction motor (IE-3 Class) suitable for 3 phase, 415 V, 50 HZ, Ac supply , Class -F Insulation, Synchronous speed not Exceeding 2900 RPM, T.E.F.C confirming to IP:55 , of required HP suitable for the above pump ,along with flexible (Love Joy type) coupling , coupling guard complete in all respect . (D) Common bed plate fabricated from mild steel channel for installation of pump and Motor including anti vibration pads.

(E) The Hydrostatic tests (2 times of design operating head or 1.5 times the shut off head whichever is higher) and performance tests (to determine developed head, Pump BHP and efficiency v/s Flow) of pumps along with trip test shall be carried out at manufacturer’s works in Virtual / Physical presence of Department’s representatives. (F) Physical & Chemical Test reports of i) Pump casing (ii) Impeller (iii) Shaft (iv) Shaft sleeve and Dynamic Balance certificate is to be submitted by OEM (G)Suitable size Reinforced cement concrete (M-30) foundation with foundation bolt, Nozing Angle of size 40mm x40mm x5 mm ( Cost of RCC Foundation to be paid Extra ) All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

180 LPM suitable for 70 Mtr Single Stage

Supplying, Installation, Testing & Commissioning submersible type dewatering pump of stainless steel casing and Noryl impellor of discharge and head given below complete with all accessories suitable for operation on 230 V, single phase/415 V /3 phase, 50 Hz. AC supply complete with starter for automatic operation including water level sensing device / float switch inter connection with submersible cable etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

180 LPM with 10 mtr head

SITC of pressure switches of pressure range 3 to 15 Bar for Main, Jockey, Terrace pump and Diesel pumps, Etc. as Required ( Control Cable from Pressure switch to Panel to be Paid Extra ). All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Providing and fixing 20/25 mm dia. (PN - 1.6, Type-S1, Flanged, ISI marked) air release valve confirming to IS - 14845 : 2000 with Double Flange isolating valve (pressure rating PN 1.6) complete with 1 no. Matching Flanges (Minimum 10 mm thick), nuts, bolts, washers, gaskets etc as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

SITC of UL listed and FM Approved Polyethelene vane type water flow switch with actuation & delay mechanism for sensitivity in the range of 4 to 10 GPM and suitable for installation in following sizes of Sprinkler pipe for a Static pressure rating up to 250 PSI in cluding making connections, making hole in pipe for inserting the vane etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

100 mm Dia.

SITC of suitable Pressure release valve of 50 mm dia, of CI body, with pressure setting range 7-15 kg/sqcm, on discharge header / Air Vessel, complete in all respect etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Providing & fixing pressure transducer in M.S. Pipe line (pressure range 0 to 10 kg/cm2) suitable for 12 volts/24 volt DC. Including connection etc. as required. ( Control Cable from Pressure Transducer to Panel to be Paid Extra ). All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

SITC of UL listed / FM Approved Brass Test and drain valve assembly for sprinkler system comprising of 3-position ( off, test and Drain ) ball valves with drain orifice having K-factor 5.6 and maximum working pressure 300 PSI and Inbuilt sight glass etc. as required of following size. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

50 mm Dia.

Providing, Fixing, Jointing, Testing & Commissioning of Heavy duty MS 'C ' class (Heavy) pipes conforming to IS 3589 / 1239 part-I for hydrant and sprinkler applications including cutting, screwing, welding etc. & forged steel fittings like elbows, tees, tapers, reducer, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps, hanger and nuts bolts including cutting hole and chase in brick or RCC walls/ slab and making good the same. complete with painting of one coats of Red Oxide and two or more coats of synthetic enamel paint of required shade complete as required. (Pipe to be tested @ 10Kgf/Sqcm for 2 Hrs.). All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

200 mm dia, 6.0 mm thick

250 mm dia, 6.35 mm thick

300 mm dia., 7.0 mm thick

Providing, Fixing, Jointing, Testing & Commissioning of Heavy duty MS 'C' class (Heavy) pipe conforming to IS 3589 / 1239 part-I for hydrant and sprinkler applications in Existing trench with cement concrete block as supports including cutting, welding etc & forged steel fittings like elbows, tees, tapers, reducer with cleaning,wrapping and coating of the pipe with 4 mm thick tar based polymaric corrosion protection tape including applying uniform coat of cold pipekot primer as per IS; 10221 for protection against corrosion complete in all respect. ( Pipe to be tested @ 10Kgf/Sqcm for 2 Hrs. & Excavation of Trench and refilling of trench to be paid extra). All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

80 mm dia

150 mm dia

Supplying and fixing cylindrical air vessel of continuous welded construction for pump room made of 450 mm dia,fabricated out of 10 mm thick dished ends and 8 mm thick MS sheet, 2000 mm in height with flanged connection, Provision for 25 mm dia drain valve,air release valve,safety valve pressure gauge as required accessories and painting with two coats of Red Oxide and two coat of post office red enamel paint including The tank shall be installed on suitable vertical legs. The legs shall be provided with M.S. Angle of size 75 mm x 75 mm x 5 mm at the bottom. The legs shall be grouted in cement concrete foundation. as required. ( Air Release valve, Drain valve, PRV, Pressure Gauge shall be Paid Extra ). All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Supplying and fixing cylindrical air vessel of continuous welded construction fixed at riser top made of 250 mm dia, fabricated out of 8 mm thick MS sheet, 1200 mm in height with flanged connection, Provision for 25 mm dia drain valve,air release valve,safety valve pressure gauge as required accessories and painting with two coats of Red Oxide and two coat of post office red enamel paint including The tank shall be installed on suitable vertical legs. The legs shall be provided with M.S. Angle of size 75 mm x 75 mm x 5 mm at the bottom. The legs shall be grouted in cement concrete foundation. as required. ( Air Release valve, Drain valve, PRV, Pressure Gauge shall be Paid Extra ). All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Supplying and Fixing of PN 16 Flanged Y strainer fabricated out of cast iron body, SS 304 strainer with perforated screen with 3 mm. dia holes in existing MS / GI pipe complete with 2 no. Matching Flanges (Minimum 16 mm thick), nuts, bolts, washers, gaskets etc as required of following sizes. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

200 mm dia

Supplying and Fixing of PN 16 Flanged Sluice valve with non rising spindle, bronze /gun metal seat confirming to IS:14846 complete with 2 no. Matching Flanges (Minimum 16 mm thick), nuts, bolts, washers, gaskets, etc as required of following sizes. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

200 mm dia

Providing and constructing masonry chamber 90 x 90 x 100 cms inside with brick work in cement mortar 1:5 (1cement : 5fine sand) for water meter ,M.S. cover (6mmthick sheet with locking arrangement, 600 x600 with M.S. frame etc. all epoxy coated and R.C.C. top slab 1:2:4 mix(1 Cement : 2 coarsesand : 4 graded stone aggregate 20mm nominalsize) including necessary excavation, back fillingfoundation concrete 1:5:10 mix (1 cement : 5 fine sand and 10 graded stone aggregate 20mmnominal size) leaving a pocket of 30x30 cmwith out concrete and filled with pebbles andinside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finishedwith a floating coat of neat cement and outside plaster finished rough complete. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Supplying and Fixing of PN 16 Cast Iron Dual Plate Wafer Type Check Valve / Non return valve with SS / Bronze flap complete with 2 no. Matching Flanges (Minimum 16 mm thick), nuts, bolts, washers, gaskets, etc as required of following sizes. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

80 mm dia

100 mm dia

150 mm dia

Supplying and Fixing of PN 1.6 Butterfly Valve (Wafer Type) with S.G Iron Disc and confirming to IS:13095 complete with 2 no. Matching Flanges (Minimum 16 mm thick), nuts, bolts, washers, gaskets, etc as required of following sizes. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Supplying and Fixing of PN 16 Brass/GM Ball valves with screwed end, SS Ball including teflon tape etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

20 mm dia.

25 mm dia.

SITC of installation control valve of cast iron body and brass/bronze working parts comprising of water motor alarm, bronze seat clapper, and clapper arm, hydraulically driven mechanical gong bell to sound continous alarm when the wet riser/Sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, with 2 no. Matching Flanges (Minimum 16 mm thick), nuts, bolts, washers, gaskets, etc as required of following sizes. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Supplying and fixing of SS 304 Single / Double headed oblique pattern hydrant landing valve (internal/external) with 75 / 100 mm dia flanged inlet & 63 mm dia instantaneous type female outlet coupling with cast iron wheel complete with ABS cap and chain and all accessories as per IS:5290-93 (Type-A) in cluding matching flange (14 mm thick), nuts, bolts, washers, gaskets, etc as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Single Headed with 75 mm Dia. Flanged Inlet

Double Headed with 100 mm Dia. Flanged Inlet

Supplying and fixing orifice plate made of 6 mm thick stainless steel with orifice of required size in between flange & landing valve of external and internal hydrant to reduce pressure to working pressure of 3.5 kg/cm2 complete with rubber gasket, GI bolts, nuts, washers etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Supplying and fixing of flexible hose made with 100% polyester, black EPDM internal rubber lining with External coat of synthetic elastomer (IS:636, type-A) 63 mm dia, 15 mtr. Long RRL hose pipe with instanteneous type 63 mm dia SS-304 male and female couplings (IS:903) duly bound and riveted to hose pipes with copper rivets and SS wire etc. as required.Appropriate Test Certificate/ report with liable warranty of product/accessories from OEM shall be submitted.

Supplying & fixing SS-304 Short Branch Pipe conforming to IS: 903:93 fitted with 20mm (nominal internal diameter) bore nozzle, for projecting water in form of solid jet. The Branch shall have 63mm Male Instantaneous Inlet, suitable for use with 63 mm size Fire fighting hoses. H.P. tested to 21 kgf/cm² for 2.5 minutes. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Supplying and fixing first -Aid Fire hose reel Drum wall mounted swinging type with MS construction powder painted in post office Red, conforming to IS 884-1985 with upto date amendments, complete with the following as required. (A) Thermoplastic / Rubber Hose (B)20 mm dia UL, FM Bronze / SS nozzle with 5mm orifice (C)Drum and brackets for fixing the equipments on wall. (D) Connections from riser with 20/25 mm dia Brass/GM gate valves with screwed end and conforming to IS:778 Class-1 through Forged steel Screwed Union & M.S. pipe. Etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

With 30 m x 20 mm High Pressure Braided Rubber Hose as per IS:5132 - 1969 and Bursting pressure 42 Kg/sqcm

Supplying and fixing Inlet Breeching Connection of CI body with Gun Metal male instantaneous inlet couplings with Inbuilt NRV, Drainage Connection with 50 mm Brass gate valve complete with PVC blank cap and chain as required for 150mm dia Outlet with 1 no. Matching Flange (Minimum 16 mm thick), nuts, bolts, washers, gaskets, etc as required of following Ways. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Providing and fixing of 100 mm Dia. Flanged Gun Metal Fire brigade Suction hose coupling (draw out connection) for female coupling as per IS:902-1974 complete with Matching Flange (Minimum 14 mm thick), nuts, bolts, washers, gaskets, etc as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Supply and Fixing of Cast iron body one side Flanged and other side strainer ball type foot valve with Reinforced rubber Nitrile rubber coated Ball including Matching Flange (Minimum 16 mm thick), nuts, bolts, washers, gaskets, etc as required of following Sizes. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

150 mm Dia. (Rate Only)

Providing and Fixing of PN16 Resilient rubber lined single arch vibration eliminators suitable for raw water up to 45 deg. C temperature, working pressure 8.5 Kg/cm2 and test pressure 14 Kg/cm2 to provide relief from stresses at pipe including Matching Flange (Minimum 16 mm thick), nuts, bolts, washers, gaskets, etc as required of following Sizes. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

150 mm Dia. x 150 mm Oal

Supplying and fixing of 750 mm x 600 mm x 250 mm Outdoor application Fire Hose Cabinet made of 1.6 mm thick MS sheet Duly powder coated in red color externally and white internally with 6 mm thick glazed doors with Expanded Metal 2 mm thick Jali including necessary locking arrangement suitable to accommodate 2 Nos 15 Mtr. Long RRL Hose and 1 No. branch pipe on Existing Wall / Angle Iron Frame as required. (Cost of MS structure for mounting Frame is to be Paid Extra) All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Providing and fixing of Fire / Electrical Shaft Door made from powder coated (50 Micron) aluminium partialy glazed with 6 mm thick glass and Partialy / Fully Louvered with Outer frame of Aluminium Section of Size 100 mm x 45 mm x 1.5 mm and Shutter's Top, Middle & side Section of Size 82 mm x 45 mm x 1.5 mm, Bottom Section of Size 110 mm x 45 mm x 1.5 mm Complete with Hinges, Tower bolt, Handle, Aldrop, Locking Arrangement including dash fasteners of required dia and size, necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. as per drawings and the directions of Engineer-in-charge. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Providing and Fixing of 15 mm dia Bronze quartzoid bulb type sprinkler heads with Maximum working pressure 11.6 Kg / Sqcm and suitable for 68 degree centigrade rating standard response (UL Listed) chrome plated complete in all respect of the following type. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Pendant/ Upright type

Sidewall Sprinklers (ordinary)(Rate Only)

Extended Throw Sidewall type .

Concealed type with Tin alloy fusible metal plate for temperature 57 degree Centigrade(Rate Only)

Providing & fixing of UL listed 1.5 mm thick chrome plated Dual type MS Escutcheon plates fixed at junction of Sprinkler piping with the false ceiling. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Supply & Fixing of Fire Man's Axe with carbon steel head & rubber moulde handel usable upto 20 KV and confirming to IS :926 with length approx 0.4 M & weight 3.0 Kg. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Providing & fixing sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

700 mm Long

1000 mm Long

1200 mm Long

Providing & fixing Stainless Steel pressure gauge with dial of 150 mm dia size and range 0 to 20 kg/sq.cm with 3 / 8 " BSP bottom entry , Ball valve , SS Syphon tube all fittings etc, duly calibrated before installation in MKS and FPS units, Accuracy Level +/- 1% including Making Drilling in Existing MS Pipe Etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Supply & Fixing of Water + AFFF 6% Mechanical Foam type Fire Extinguisher (Stored Pressure type) conforming to IS:15683:2018 , Powder coated Internal & External Surface Deep drawn cylinder body of Mild Steel CR2 grade conforming to IS: 513, Squeeze grip Forged brass release valve with Inbuilt safety release device, Diaphragm Type, 0 to 25 bar range pressure gauge, 450 mm long EPDM discharge tube, QR code for Product Traceability including Fixing on wall with suitable Anchor Fasteners as required of following capacity. Test Certificates of all the Parameters along with Hydro test & Burst test (For Cylinder Body) Certificate from OEM / External NABL Accrediated Lab is to be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Capacity - 6 Ltrs.

Capacity - 9 Ltrs.

Supply & Fixing of CO2 type Fire Extinguisher conforming to IS:15683:2018, charged with CO2 gas (purity 99.7% conforming to IS 15222), Powder coated Internal & External Surface Manganese steel ISI marked as per IS 7285 cylinder body , Wheel type Forged brass release valve ISI Marked as per IS 3224 with Inbuilt safety release device ((Fusible plug and Rupture Disc Type), 1.0 Mtr. Metal wire braided hose having minimum bursting pressure of 140 Kgf/cm2, Horn with metallic thread connection, QR code for Product Traceability, including Fixing on wall with suitable Anchor Fasteners as required of following capacity. Test Certificates of all the Parameters along with Hydro test & Burst test (For Cylinder Body) Certificate from OEM / External NABL Accrediated Lab is to be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Capacity 3.0 Kg.

Capacity 4.5 Kg.

Supply & Fixing of Dry Powder Agent (as per IS 4308:2019), ABC type Fire Extinguisher (Stored Pressure type) conforming to IS:15683:2018 , Powder coated Internal & External Surface Deep drawn cylinder body of Mild Steel CR2 grade conforming to IS: 513, Squeeze grip Forged brass release valve with Inbuilt safety release device, Diaphragm Type, 0 to 28 bar range pressure gauge, 450 mm long EPDM discharge tube, QR code for Product Traceability including Fixing on wall with suitable Anchor Fasteners as required of following capacity. Test Certificates of all the Parameters along with Hydro test & Burst test (For Cylinder Body) Certificate from OEM / External NABL Accrediated Lab is to be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Supply & Fixing of Trolley mounted 22.5 Kg CO2 type Fire Extinguisher conforming to IS: 16018:2012, charged with CO2 gas (purity 99.7% conforming to IS 15222), Powder coated Internal & External Surface Manganese steel ISI marked as per IS 7285 cylinder body , Wheel type Forged brass release valve ISI Marked as per IS 3224 with Inbuilt safety release device ((Fusible plug and Rupture Disc Type), 1.5 Mtr. long Metal wire braided hose having minimum bursting pressure of 140 Kgf/cm2, Horn with metallic thread connection, QR code for Product Traceability, including Double mounted handle as required of following capacity. Test Certificates of all the Parameters along with Hydro test & Burst test (For Cylinder Body) Certificate from OEM / External NABL Accrediated Lab is to be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Supply & Fixing of Ceiling mounted Dry Powder Agent (as per IS 4308:2019), Modular stored pressure type ABC Fire Extinguisher , Powder coated Internal & External Surface Deep drawn cylinder body of Mild Steel CR2 grade conforming to IS: 513, Fixed Bulb with Temerature 68 deg C, QR code for Product Traceability including Fixing on Ceiling with suitable Anchor Fasteners as required of following capacity. Test Certificates of all the Parameters along with Hydro test & Burst test (For Cylinder Body) Certificate from OEM / External NABL Accrediated Lab is to be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

5 Kg Capacity

Supply & Fixing of Ceiling mounted UL listed clean Agent (HFC-236fa), Modular type Fire Extinguisher , Powder coated Internal & External Surface Deep drawn cylinder body of Mild Steel CR2 grade conforming to IS: 513, Fixed Bulb with Temerature 68 deg C, QR code for Product Traceability including Fixing on Ceiling with suitable Anchor Fasteners as required of following capacity. Test Certificates of all the Parameters along with Hydro test & Burst test (For Cylinder Body) Certificate from OEM / External NABL Accrediated Lab is to be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

10 Kg Capacity

Supplying and Fixing of Galvanized Mild Steel fire bucket Confirming to IS: 2546 : 1974 with one coat of primer and two coat of enamel paint of approved shade on Angle Iron ( 50 x 50 x 5 mm) Stand of Size 800 x 1240 x 400 mm with MS 22 SWG Galvanized Canopy, 4 Hooks for Buckets including associated civil works etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Providing and fixing signages as per required content printed on photoluminescent U1000 aluminium sheet of 1.0 mm (+-10%) containing Lumigen II as base chemical, covered under UV stablized coating with suitable colour combination (Glow in dark) with high intensity properties for indoor surface glow visibility not less than 6 hrs. in total darkness and of appropriate size including fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc. complete in all respects required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Single sided signage board

Double sided signage board

Providing and fixing of Aluminium housing body self contained Rechargeable LED Emergency Light with required content and Size Approx. 300 mm x 180 mm, confirming to IS:9583 :1981with Ni-Mh / Ni - Cd Battery, 3 Hrs Back Up, Constant Current Charger, Input Voltage 230 V , 50 Hz including fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc. complete in all respects required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached as per Rajasthan PWD Electrical BSR 2022 .

Single sided signage

Double sided signage

Description of Work / Item(s)

Amount

Supply / installation / testing and commissioning of 26 persons, 1768 kg in with machine room , 1.75 M/sec travel speed , 11 Stops, 11 Openings , Duplex control as per detailed specifications and recommended makes given in RFP.Gearless machine located in the machine room .

Description of Work / Item(s)

Amount

Passive Networking - Copper Cabling

SITC of 10G, ETL Verified Category 6A U/UTP Cable, White jacket, 4 pair count, LSZH Sheath as per IEC 60332-3-22, 1000 ft (305 m) length

SITC of Category 6A U/UTP Loaded Patch Panel, 24 port, Intelligent Upgradable

SITC of Cat 6A-10G, Solid Low Smoke Zero Halogen as per IEC 60332-3-22, Cordage Modular Patch Cord, BLUE Jacket, 3 Feet (At Rack ends)

SITC of Cat 6A, 10G Information Outlet, Color BLUE (At User ends)

SITC of Cat 6A-10G, Solid Low Smoke Zero Halogen as per IEC 60332-3-22, Cordage Modular Patch Cord, BLUE Jacket, 10 Feet (At User ends)

SITC of 3*3, Square faceplate One port with Shutter(At User ends)

SITC of Cable Management Panel, horizontal, 1U, black (At Rack ends)

Passive Networking - Fiber Cabling

Supply of 12 Core, Multi Mode(OM4) Bend-Insensitive, Indoor/Outdoor Low Smoke Zero Halogen Riser Distribution Cable, 12 fiber single-unit, Meet Standard ANSI/ICEA S-83-596 /Telcordia GR409

Supply of 19" Rack Mount, 48F LIU, 1U Sliding shelf with 4 slots for accepts 4 Nos. of LC Multi mode, OM4 Cassette/Adapter Plate.

Supply of 12 LC Cassettes/Adapter plate, Multi Mode(OM4), Aqua, Intelligent Ready

Supply of LC to Unconnectorized, Multi Mode(OM4) Fiber Pigtail, LSZH Sheath, yellow jacket, 3 ft

Supply of Fusion Splice Kit/Splice Trays, for 1U Shelf

Supply of 19" Rack Mount, 12/24F LIU, 1U Sliding shelf with 4 slots for accepts 4 Nos. of LC Multi mode, OM4 Cassette/Adapter Plate.

Supply of 12 LC Cassettes/Adapter plate, Multi Mode(OM4), Aqua, Intelligent Ready

Supply of LC to Unconnectorized, Multi Mode(OM4) Fiber Pigtail, LSZH Sheath, yellow jacket, 3 ft

Supply of Fusion Splice Kit/Splice Trays, for 1U Shelf

Supply of LC to LC, Bend-Insensitive, Multi Mode(OM4) Fiber Patch Cord, 1.6 mm Duplex, LSZH Sheath as per IEC 60332-3, 10 Feet.

Smart rack Integrated data center for E-Gov setup

Supply installation, testing and commissioning of integrated smart racks as per detail specifications enclosed comprising of 4 racks for servers and storage, network equipments, inbuilt precision air conditioning, Novac fire supression system, CCTV and DVR, LED lighting, IP based biometric access control system, rodent control system, UPS, fire alarm system, iPDUs for 3 phase/single phase supply as required (2 per rack), temperature and humidity monitoring, door switch and water leakage sensors, becon alarm. - Refer to detailed tech specs & Approved makes as per RFP.

Racks

SITC of 27U Closed Network Rack with front glass door, rear steel Double door, 800mmx800mm, castor wheels, 2 Equipment Shelf, 15 Amp, AC power supply Vertical with 10 sockets- 2 nos, 4 fans at top Mounted, earthing kit and Mounting Accessories.

SITC of 42U Closed Network Rack with min 60% hexagonal perforation Front & Rear Spilt Door., castor wheels, 2 Equipment Shelf, 15 Amp, AC power supply Vertical with 16 sockets- 2 nos, 4 fans at top Mounted, with atleast 15 1U cable managerseach rack, earthing kit and Mounting Accessories.

Supply, Installation,Testing and Commissioning OF 1U Horizontal Cable Manager

Active networking components

SITC of edge router as per detailed technical specification and preffered make mentioned in RFP

12 port Core Switch (Type-1- for education department)

SITC of Core Switch Type 1 in HA: Supply , installation , Testing and Commissioning of Core Switch with minimum 12 25G/10G/1G SFP28 and additional 2 40/100G QSFP+/QSFP28 uplink ports populated with required interface transeiver as per technical specifications and design 5 yrs Warranty as per detailed specifications and Prefered make

24 port Core switch (Type-2 - for e-gov)

SITC of Core Switch Type 1 in HA: Supply , installation , Testing and Commissioning of Core Switch with minimum 24X25G/10G/1G SFP28 and additional 4X 40/100G QSFP+/QSFP28 uplink ports populated with required interface transeiver as per technical specifications and design 5 yrs Warranty as per detailed specifications and Prefered make

Access Switces for E-Gov

SITC of 24 Port Access Switch POE: Supply , installation , Testing and Commissioning of Access Switch with min. 16x1G & 8X1G/10G POE ports and min. 4X10G uplink ports as per technical specifications, 5 yrs Warranty as per detailed specifications and Prefered make

SITC of 48 Port Access Switch non POE: Supply, installation,Testing and Commissioning of 48X1G ports & min. 4X10G for uplink non-POE Access Switch with in 1 RU fixed Form factor populated with 5 yrs Warranty as per detailed specifications and Prefered make

Access Switces for Education department

SITC of 24 Port Access Switch POE: Supply , installation , Testing and Commissioning of Access Switch with min. 16x1G & 8X1G/10G POE ports and min. 4X10G uplink ports as per technical specifications, 5 yrs Warranty as per detailed specifications and Prefered make

SITC of 48 Port Access Switch non POE: Supply, installation,Testing and Commissioning of 48X1G ports & min. 4X10G for uplink non-POE Access Switch with in 1 RU fixed Form factor populated with 5 yrs Warranty as per detailed specifications and Prefered make

WAN Switch for E-Gov

SITC of WAN switch to connect 2 ISPs and core routers in HA mode. Should have 12 25G/10G/1G SFP28 and additional 2 40/100G QSFP+/QSFP28 uplink ports 1 RU fixed Form factor populated with required interface transeiver as per design with 5 yrs Warranty as per detailed specifications and Prefered make

Firewall for E-Gov

SITC of Firewall Type-1 to be configured in HA with 5 yrs Warranty along with Central Management and Reporting tools for Firewall management as per detailed specifications and Prefered make

Firewall for Education department

SITC of Firewall Type-2 to be configured in HA with 5 yrs Warranty along with Central Management and Reporting tools for Firewall management as per detailed specifications and Prefered make

Wireless Access points and controller for E-Gov

SITC of Indoor Access Point radio should be minimum 2x2 MIMO with 2 special stream on 2.4Ghz and minimum 4x4 MIMO with 4 special stream 5ghz . AP should be supplied with OEM mounting bracket and should be covered under 5 years OEM warranty & support as per detailed specifications and Prefered make

SITC of Hardware based wireless LAN controller to manage both WiFi from a single GUI.OEM Warranty & support 5 years is required. as per detailed specifications and Prefered make

Licenses to integrate Ap's into wireless LAN controller with 5 years support and warranty

Wireless Access points and controller for Education department

SITC of Indoor Access Point radio should be minimum 2x2 MIMO with 2 special stream on 2.4Ghz and minimum 4x4 MIMO with 4 special stream 5ghz . AP should be supplied with OEM mounting bracket and should be covered under 5 years OEM warranty & support as per detailed specifications and Prefered make

SITC of NMS solution for access point monitoring with required licenses as per technical specifications and preferred make

AAA Authentication server for E-Gov

SITC of AAA Server for user authentications - Identity and Access Management/NAC - Base License supports up to 3000 users. Expand user support to 5000 users with 5 yrs Warranty as per detailed specifications and Prefered make

Jakson Limited

VARINDERA CONSTRUCTIONS LIMITED

VARINDERA CONSTRUCTIONS LIMITED

Jakson Limited

Jakson Limited

VARINDERA CONSTRUCTIONS LIMITED

Jatan Constructions Pvt Ltd

VARINDERA CONSTRUCTIONS LIMITED

Jakson Limited

VARINDERA CONSTRUCTIONS LIMITED

VARINDERA CONSTRUCTIONS LIMITED

Jakson Limited

VARINDERA CONSTRUCTIONS LIMITED

Jakson Limited

Jatan Constructions Pvt Ltd

Jakson Limited

Jakson Limited

VARINDERA CONSTRUCTIONS LIMITED

Jatan Constructions Pvt Ltd

VARINDERA CONSTRUCTIONS LIMITED

Jatan Constructions Pvt Ltd

Jakson Limited

Jatan Constructions Pvt Ltd

VARINDERA CONSTRUCTIONS LIMITED

Jakson Limited

VARINDERA CONSTRUCTIONS LIMITED

Jakson Limited

VARINDERA CONSTRUCTIONS LIMITED

Jakson Limited

VARINDERA CONSTRUCTIONS LIMITED

VARINDERA CONSTRUCTIONS LIMITED

Jakson Limited

Jatan Constructions Pvt Ltd

VARINDERA CONSTRUCTIONS LIMITED

Jakson Limited

VARINDERA CONSTRUCTIONS LIMITED

Jakson Limited

VARINDERA CONSTRUCTIONS LIMITED

Jatan Constructions Pvt Ltd

Jakson Limited

Jatan Constructions Pvt Ltd

Jakson Limited