Construction of Office Building for Division No 3 Jalandhar District Jalandhar

Amount

Constructions of Office Building for XEN

Earth work in excavation in foundations, trenches etc. in all kinds of soil where pick jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm layers with compaction including disposal of all surplus soil as directed within a lead of 30 meters.

Cement concrete 1:5:10 with 40 mm stone ballast using concrete mixing volumetric type. (including carriage)

Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth. (including carriage)

Reinforced cement concrete M-20 mechanicaly batch mixed using batch type concrete mxier as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in super structure. (including carriage)

Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering)

Centring and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc.

Centring and shuttering for sides and soffits of beam, beams launchings girders bressumers, lintels

First class burnt brick work laid in cement sand mortar 1:6 in foundation and plinth. (including carriage)

First class burnt brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level. (including carriage)

Extra for additional story upto 4m above the top of structural roof of lower story.

115 mm thick brick wall with every fourth course reinforced with hoop iron laid in 1 :4 cement sand mortar in super structure (including carriage)

12.50 mm Cement Plaster 1:5 on walls (including carriage)

20 mm thick Cement Plaster 1:5 in two coats work. (including carriage)

12.5 mm thick cement plaster 1:4

20 mm thick Cement Plaster 1:4 in two coat work. (including carriage)

Bearing Plaster of 10 mm thick cement mortar 1:3 cement sand finished with a floating coat of neat cement and thick coat of Lime wash / P.O.P. on top of walls when dry for bearing of R.C.C. slabs & beams. (including carriage)

Providing and fixing 110 mm dia SWR U.P.V.C Rain water pipe (ring fitted type-A) as per IS:13592 including jointing during masonary complete as per specifications and to the entire satisfaction of Engineer-in-charge. (If fixed on wall face clamp to be paid separatly as per respective item)

Providing and fixing 110 mm dia SWR U.P.V.C bend for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer-in-charge.

Providing and fixing 110 mm dia SWR U.P.V.C Coupling/Sockete for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge.

Providing and fixing in position M.S. or heavy flat iron clamps made out of M.S. flat iron not less than 5 mm of the approved design for fixing C.I. soil waste, vent or antisyphonage pipes to walls complete in all respects. Including cutting and making good the walls and floor etc. and painting. (M.S. Holder Bats clamps 100 mm i/d H.C.I. pipes)

Top khurra 0.6m x 0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50mm thick cement concrete 1:8:16. (including carriage)

Providing and fixing in position gratings of approved make (to the approval of Engineer Incharge) size150 mm x 150 mm on (gully trap) top Khura PVC grating.

Bottom Khurra on ground 1.2m x 0.6m consisting of brick on-edge laid in cement mortar 1:3 over 75mm cement concrete 1:8:16 including 12.5mm thick cement plaster 1:3 (including carriage)

Terracing consisting of tiles 22.86 x 11.43 x 3.83 cm laid over 25 mm mud plaster 7.5 cm mud filling on another laver of 25mm mud plaster including two coats of bitumen laid hot at 1.65 Kg/sqm top of CC slab including grouting with cement sand mortar 1:4 and top surface to be left clean after wire brushing etc. (including carriage)

Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified. (including carriage)

Earth filling with good quality earth obtained from outside the plinth including compensation of earth, loading, unloading, carriage from outside the premises to site of work, spreading, laying watering compacting with rammer complete as per specifications.

Earth filling under floors with surplus ordinary soil or soil containing gravel or kankar up to 40% excavated from foundation and taken only from outside the building plinth in 15 cm layers including ramming, watering and consolidating lead up to 30 metres

Base course of floor consisting of 100 mm thick cement concrete 1:8:16 with stone aggreate and 100 mm sand filling.(using mechanical mixer for mixing of material) (including carriage)

Kota stone tile flooring 20mm to 30 mm thick over 12.5mm thick base of cement mortar 1:3 (1 cement, 3 Sand) laid and jointed with neat cement slurry, mixed with pigment to match the shade of stone including rubbing and polishing.

Providing and fixing Morwad Marble strip 18 mm to 20 mm thick and 100 mm wide in Kotah Stone Flooring over 12.50 mm thick base of cement mortar 1:3 jointed with cement slurry including cost of additional mortar equivalent to the kotah stone thickness and colouring pigment to match the colour rubbed and polished to granolithic finish complete in all respects. (including carriage)

Providing and laying vitrified floor tiles 600x600mm size premium quality, manufactured using Double Charge Technology, with water absorption less than 0.08% and conforming to IS: 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement 4 fine sand) for new flooring laid with cement based high polymer modified quick set title adhesive (water based ) of approved make IS 15477 marked using 5 Kg. adhesive per sqm of tile area in average 3mm thickness over existing base, including grouting the joints (Tiles to be laid with 2mm to 3mm gap using spacers and later this gap to be filled with cement based grout) with cement base grout and matching pigments etc. complete. (including carriage) (design is homogenous throughout the tile body)

Providing and Laying Out Door Precast Designer chequered tiles of any size & any shape 25mm thickness having top layer of white cement mixed with pigment, laid on 20mm thick bed of ordinary cement mortar 1:3 (1 ordinary cement :3 fine sand), joints grouted with white cement slurry containing pigment to match the shade complete in all respect as per specifications and to the entire satisfaction of engineer-in-charge. (including carriage)

Supply & fixing of door frames (Chowkhats) consisting frame fabricated from sheet roll formed out of 1.2 mm thick galvanized sheet as per IS:277 (base steel as per IS:513) with zinc of 120 gm/Sqm. & Powder coated with pure Polyster powder up to 50 micrones (as per approved colour), 3 Nos. 100 mm but hinges 2 mm thick, 6 Nos. 1.2 mm thick CRCA electroplated stiffner, 6 Nos. M.S. hold fast with split and tail welded to stiffner plate 200 mm long, Receiver for adrop, M.S. tie rod 50 mm x 25 mm to be fixed at bottom finished with powder coated total thickness of coating 0.60 mm of approved shade, fixed in position, including the cost of cement concrete for 1:2:4 for fixing lugs complete in all respects as per drawing, design, specification and entire satisfaction of Engineer-in-Charge.

Doors frame of size 80 mm x 50 mm with 37 mm wide single rebate for 35 mm door shutter.

Doors frame of size 125 mm x 60 mm with 37 mm wide double rebate for 35 mm door shutter.

Supply & Fixing of Window frames (Chowkhats) including mullions consisting frame fabricated from sheet roil formed out of 0.58mm thick galvanished sheet (base steel as per IS : 513) with zinc of 120gm/sqm steel sheet pre coated (as per approved colour) with polyster paint of 12-16 micrones thickness under coat of EPDXY primer & back coated with ALKYD backer of 5-7 micrones total thickness of coating 0.58mm of approved shade, fixed in position by means of PVC & metal hold fastner with PVC cap complete in all respects as per drawing, design, specification & entire stasfication of Enginner-in-Charge.

Windows Outer frame of size 72 mm x 55 mm and central mullion 72 mm x 50 mm with Double rebate.

Supply & Fixing of Window shutter consisting frame fabricated from sheet roll formed out of 0.58mm thick galvanished sheet (base steel as per IS : 513) with zinc of 120gm/sqm steel sheet pre coated (as per approved colour) with polyster paint of 12-16 micrones thickness under coat of EPOXY primer & back coated with ALKYD backer of 5-7 micrones total thickness of coating 0.58mm of approved shade, fixed in position by means of screws complete in all respects as per drawing, design, specification & entire stasfication of EngInner-in-Charge.

Glazed Windows shutter Section 47 mm x 20 mm (Without Glass)

Wire Mesh Windows shutter Section 40mm x 20mm with S.S wire mesh 32 guage flymesh with 144 holes per square inch

Providing 8, fixing fixed beeding 12 mm x 12 mm for fixed glass with ECO fixed gasket (EPDM)

Providing and fixing glazing in door, window, ventilator shutters and partitions etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of Gasket /beading shall be paid as per respective item)

Float Glass panes of 5.5 mm thickness

Wrought iron and mild steel ladders, framed grills, grating etc. with ends of bars, riveted or welded or forged, framed window guards, barred iron doors, stair case, iron railing including cost of bolts and nuts or screws or welding rod, complete fixed in position. (including carriage)

Providing Polyster Powder coating 60 to 70 micron any coloured specrified to M.S Grill section of various sizes including carrriage of material from marktet to workshop ..

Providing and fixing 16 gauge stainless steel pipe of various sizes railing of grade 304 duly fixed on ramp with the help of bolts grouted on floor with hand rail and newel post of 50 mm dia stainless steel pipe, balusters of 40 mm dia stainless steel pipe complete in all respect as per specification and entire satisfaction of Engineer-in-Charge. (Railing on Entrance Ramp Design as per guidelines issued for persons with disability)

Factory manufactured flush door fixed in position iron hinges, etc (excluding the cost of any fittings other than specified above but including labour for fixing the same in position (Code : II Revision IS-2191 Part-I) 1973 Commercial with elm or gurjan facing on both \ Sides with laminated core and lipped edges:- 35 mm thick

35 mm thick

Cost of Aluminium fittings complete for doors, windows such as tower bolts, handless and screw etc. for these fittings (Excluding sliding bolt)

Providing and fixing aluminium sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 300 mm x 16 mm

Providing and fixing 0.50 mm thick aluminium sheet including cost of necessary fittings i.e. screws, etc. complete

Providing and fixing hydraulic door closer ISI mark with necessary screw etc. complete - I.S.I Designation No. III (size of door 851 mm to 1000 mm)

Providing and fixing 12mm thick 150mm wide pelmets with 25mm dia Aluminium rod and brackets including fixing with 25mmx3mm MS Flat 10cm long and PVC Plug etc complete Deodar Wood

Providing and fixing of false ceiling at all heights of 600 x 600 x 15 mm / 600 * 1200 * 15 mm Mineral Fibre ceiling tiles of type DUNE RH-99 laid in grid system. The frame work comprise of made of GI 120 GSM coating with minimum 0.3 mm thickness main runner spaced at 1200 mm centre to centre securely fixed to the structural soffit by approved hangers at 1200 mm maximum centres. Hangersa (GI wire of 4 mm dia) to be fixed by approved roof plug, level adjusters and screw etc. The last hanger at the end of each main runner should not be greater than 450 mm from the adjacent wall. Flush fitting 1200 mm long cross tees (with double stitching) to be interlocked between main runners at 600 mm centres to form 1200 x 600 mrn modules. Cut across tees longer than 600 mm to be supported independently. 600 x 600 mm modules to be formed by fitting 600 mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be Armstrong wall angle secured to walls at 450 mm maximum centres complete in all respects as per specifications.

Cold twisted deformed (Ribbed/ Tor Steel Bar) Bars Fe 500 grade as per IS 1786-2008, for R.C.C works, where not including in the complete rate of RCC including bending and placing in position complete. (including carriage)

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two coats to get required finish

Applying priming coat with cement primer in all shade on newly plastered or concrete exterior surface

Wall painting with plastic emulsion paint of approved brand and manufacturer to give an even shade (two coats)

Preparation of plywood surface for painting including sand papering the surface and applying filling with approved quality fillers consisting of white lead, linseed oil, Varnish, and Chalk Mitti including finishing the surface to required finish complete.

Applying pink primer or aluminum priming coat on wood work including preparation of surface knotting and stopping etc.

Painting two coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade. - With ordinary quality Paint

Finishing walls with Premium Acrylic smooth exterior paint with silicon additives of required shade with two coats applied @ 1.43litre/10 sqm over and including base coat of water proofing Cement Paint applied @ 2.20 Kg/10 Sqm.

Construction of Plinth Protection complete as per drawing Earth work in excavation in foundations, trenches etc. in all kinds of soil where pick jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm layers with compaction including disposal of all surplus soil as directed within a lead of 30 meters.

Cement Concrete 1:8:16 with 40 mm gauge stone aggregate using concrete mixing volumetric type (including carriage)

First class burnt brick work laid in cement sand mortar 1:5 in foundation and plinth. (including carriage)

Earth filling with good quality earth obtained from outside the plinth including compensation of earth, loading, unloading, carriage from outside the premises to site of work, spreading, laying watering compacting with rammer complete as per specifications.

Base course of floor consisting of 100 mm thick cement concrete 1:8:16 and 100 mm sand filling. (including carriage)

Conglomerate floor 40 mm thick cement concrete topping 1:2:4 (using mechanical mixer for mixing of material). (including carriage)

12.5 mm thick cement plaster 1:5 complete in all respect as per specification, drawing and to the entire satisfaction of Engineer-in-charge. (including carriage)

Sub Head-1 : Internal Sewerage System Providing and fixing in position SWR UPVC soil waste vent or antisyphonage pipes as per IS -13592 of approved make (to the approval of Engineer-in-charge) including cutting, jointing, wastage, but including cost of jointing. Complete in all respect Type B

110 mm o/d SWR UPVC pipe line laid complete

75 mm o/d SWR UPVC pipe line laid complete

Providing and fixing in position SWR UPVC specials for soil waste vent or anti syphonage pipes as per as per IS - 14735 of approved make (to the approval of Engineer-in-charge) including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but including cost of joining.

Qty. as per Table attached

For 110 mm o/d pipes

Bend Plain

Collar

For 75 mm o/d pipes

Bend Plain

Collar

P-trap/Floor Trap 75mmX75mm

Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150 mm x 150 mm , cover and frame clear opening 300 mm x 300 mm and out of side size 330 mm x 330 mm and chamber including cost of all bricks work in cement mortar 1:5 cement concrete 1:2:4 in coping around cover and frame etc. as per standard design minimum depth of water should be 150 mm with a minimum seal 50 mm.

100 mm internal Diameter S.W. Gully trap with H.C.I. grating and cast iron cover weighing approximately 7.26 kg. and frame clear opening 300 mm x 300 mm and out of side size 330 mm x 330 mm

Construction of brick masonry inspection chambers size as given below up to 0.60 metre average depth in 1:5 cement sand mortar, lime concrete with 40 per cent lime mortar 2:3 in foundation, cement concrete 1:2:4 benching 12.50 mm thick cement plaster 1:2 with a floating coat of 1 mm thick of neat cement, R.C.C. 1:2:4 slabs 100 mm thick cement concrete topping 50 mm thick with 455 mm x 455mm, 455 mm x 610 mm inside light duty C.I. inspection chamber cover and frame (Weight as per I.S.I specifications) painted with 3 coats of black bitumastic paint conforming to I.S.I complete as per standard design.

Size 450 mm x 450 mm inside with RCC 455 mm x 455 mm cover and frame light duty double seal

Providing, laying, jointing, fixing and testing ISI Marked uPVC Pipe with G.I. specials as per ISI-4985, including cost of G.I. specials such as tees, bends, sockets, elbows etc. testing inside building complete.

uPVC Pipe 6 Kgf/cm2 - 50 mm i/d

Sub Head-2 : Internal Water Supply System Providing, laying, jointing, fixing and testing ISI Marked G.I. Pipe (as per IS 1239) B-Class including cost of specials (such as tees, bends, sockets, elbows etc.), painting with anti corrosive bitumastic paint, testing, cutting, threading Inside building complete.

Cutting chase in brick walls in cement or in floor for embedding G.I. or C.I pipes line and making good the same to its original condition. Size 75 mm x 75 mm

Cutting holes up to 23 cm square through B.B. in cement walls or stone masonry wall in cement for pipes, and making good the same & finishing according to existing finish where required.

Through wall 11.43 cm thick

Through wall 22.86 cm thick

Providing, fixing and jointing G.I Union Couplings (of approved make with the approval of EIC) as per IS 1879 in G.I. Pipe lines complete in all respect.

15 mm i/d G.I. Union

20 mm i/d G.I. Union

25 mm i/d G.I. Union

40 mm i/d G.I. Union

Providing, fixing and jointing Brass Ball valves screwed with SS/BRASS ball & spindle & Teflon seats, on G.I. Pipe lines including all carriages complete.

25 mm i/d Brass Ball valves

40 mm i/d Brass Ball valves

Painting G.I. Pipes and Specials with synthetic enamel Paint in all shades as per I.S.I. specification on existing or new work, two coats paints including cleaning rubbing surface, etc.

15 mm & 20 mm i/d G.I. Pipe

25 mm & 32 mm i/d G.I. Pipe

40 mm & 50 mm i/d G.I. Pipe

Sub Head-3 : Sanitary Installation Providing and fixing in position Chinaware Indian Orissa water closet size 580 mm of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern including cost of PVC long bend 32 mm dia complete in all respect and to the entire satisfaction of Engineer-in-charge.

Providing and fixing in position Chinaware European type water closet P trap or S trap of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern, PVC short bend 32 mm dia including cost of seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge.

Providing and fixing in position Chinaware wall hanged European type water closet with P trap or S trap of approved make (to the approval of the Engineer-in-charge) with or without 10 ltr. chinaware matching flushing cistern and seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge.

Chinaware wall mounted E.W.C without cistern including seat cover complete in all respect.

Extra cost for pastel colour instead of white W.C. vitreous fixtures.

Chinaware extended wall mounted E.W.C. with matching chinaware cistern 10 ltr. Capacity.

Providing and fixing in position Metro pole flush valve 32 mm size dual flow (Concealed body) with exposed shut off provision and round plate complete in all respect.

Providing and fixing jet spray with 2'-6" long PVC pipe with PTMT nut

Providing & Fixing in position C.P. Brass Hexa Nipple 15 mm of approved make (to the approval of Engineer-in-charge) complete in all respect.

Providing and fixing in position vitreous Chinaware white large flat back or angular lipped front urinal 610 mm high of approved make (to the approval of the Engineer-in-charge) (610 mm x 410 mm x 380 mm) consisting of C.P. waste 32 mm dia and C.P. brass spreader, complete.

Extra cost for pastel colour instead of vitreous Chinaware white Urinal fixtures.

Chinaware white large flat back or angular lipped front urinal 610 mm high (610 mm x 410 mm x 380 mm)

Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) consisting of C.P. brass waste 32 mm dia with one C.P. brass pillar tap complete in all respect. Size 550 mm x 400 mm

Extra cost for pastel colour instead of white vitreous Chinaware Lavatory suites.

Lavatory suites Size 550 mm x 400 mm

Providing and fixing vitreous chinaware standard pedestal of approved make (to the approval of Engineer-in-charge) for wash hand basin complete in all respect.

Extra cost for pastel colour instead of white vitreous Chinaware pedestal for wash hand basin.

Providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing in position stainless steel sinks of approved make 1 mm thick, grade-304 (18/8) with waste coupling complete in all respect.

Size 600 mm x 450 mm x 225 mm (Net size excluding flat edge)

Providing & fixing in position PVC flexible tube connection of approved make (to the approval of Engineer-in-charge) complete in all respect - PVC tube connection of size 15 mm x 375 mm with PTMT nut

Providing and fixing PVC waste pipe 32 mm complete in all respect.

Providing and fixing in position C.P. brass, bottle trap 32 mm dia with 40 mm seal of approved make (to the approval of Engineer-in-charge) complete in all respect.

Providing and fixing in position C.P. brass soap dish of approved make (to the approval of Engineer-in-charge) fixed into wall with rawl plugs and C.P brass screws complete in all respect.

Providing and fixing in position towel rails / ring of approved make (to the approval of Engineer-in-charge) fixed in with rawl plugs embedded in walls with brass screws complete in all respect - C.P. brass towel Rails size 15 mm dia 600 mm long

Providing & Fixing in position 15 mm i/d bib cock of approved make (to the approval of Engineer-in-charge) complete in all respect.

C.P. brass Bib cock long nose/ long body without flange

C.P. brass Bib cock without flange

Providing & Fixing in position stop cock / Angle valve of approved make (to the approval of Engineer-in-charge) complete in all respect.

C.P. Brass 15 mm Angle valve without flange

C.P. Brass 15 mm Concealed stop cock with flange.

Providing & Fixing in position C.P. Brass flange of approved make (to the approval of Engineer-in-charge) under various fixtures complete in all respect.

Providing & Fixing in position C.P. Brass extension piece 25 mm long to 50 mm long of approved make (to the approval of Engineer-in-charge) with various fixtures complete in all respect.

Providing & Fixing in position 5 mm thick bevelled edge mirror of superior glass (of approved make) complete with 4 mm thick hard board backing fixed in with rawl plugs 50 mm , C.P. brass screws and washers complete in all respect (as required by the Engineer-in- Charge) - Size 600 mm x 450 mm.

Providing and fixing in position premium range C.P. Brass Fittings and accessories of approved make (to the approval of Engineer-in-charge) complete in all respect. (Note:-To be provided only for VIP Installations and with prior approval of the Engineer-in-charge.)

C.P. brass Bib cock with wall flange

C.P. Brass 15 mm Angular stop cock with Wall flange

C.P. Brass 15 mm Concealed stop cock with adjustable wall flange.

C.P. brass Central hole basin mixer without popup system with 450 mm long flexible hose

Providing and fixing in position premium range C.P. Brass Fittings and accessories of approved make (to the approval of Engineer-in-charge) complete in all respect. (Note:-To be provided only for VIP Installations and with prior approval of the Engineer-in-charge.)

C.P. brass toilet paper holder

C.P. brass soap dish

CP brass Acrylic Shelf size 460 mm x 130 mm

C.P. brass towel bracket (610 mm long)

Providing & Fixing in position C.P./ Aluminium Khunti of approved make (to the approval of Engineer-in-charge) fixed into wall with C.P. brass screws and rawl plugs etc. complete in all respect - C.P. Brass khunti with 3 pegs

Providing and fixing in position vitreous Chinaware white channel of approved make (to the approval of Engineer-in-charge) of size 600 mm x 100 mm including laying and fixing in cement concrete 1:2:4 complete in all respect.

Providing & placing in position on terrace (at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer -in-charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fittings and base support for tank - Double Layer Tanks

2000 Litres capacity

1000 Litres capacity

500 Litres capacity

Providing and fixing in position automatic brass Ball Cock in tanks.

Brass Ball Cock with rod and Plastic Ball.25 mm i/d

Brass Ball Cock with rod and Plastic Ball.32 mm i/d

Providing and fixing in position G.I. Tank Nipple of approved make (to the approval of Engineer-in-charge) in PVC Water storage tanks complete in all respect.

G.I. tank nipple 25 mm i/d

Construction of Platform for placing PVC Water Storage Tank with Brick Ballast Work, Plaster, CC 1:8:16, CC 1:2:4, cement rendering etc. of required size complete in all respect.

Sub Head-4 : Flooring and Wall Tiles Base course of floor consisting of 100 mm thick cement concrete 1:8:16 with stone aggreate and 100 mm sand filling.(using mechanical mixer for mixing of material) (including carriage)

Providing and laying Rectified Procelain floor tiles 400x400 or more (thickness to be specified by the manufacturer) of premium quality conforming to IS:15622 of approved make in all colours laid on 20mm thick bed of Cement Mortar 1:4 (Cement : 4 Fine sand) for new flooring Complete Rectified tiles have finished edges allowing them to be placed closer together for a narrower grout joint as opposed to other tiles and are more expensive. Unlike typical factory-edged tile, rectified tile is cut to size after the firing process. This process creates a precise, 90 degree angle edge and, as a result, can be laid with a tighter grout joint than unrectified tile. It gives a smooth, sophisticated and continuous look to the floor. Using a rectified tile allows you to place the tiles much closer together using tighter joint spacing. This makes the grout less visibale as there is actually less grout used. When a wide space is used between tiles, the grout become a distinct part of the design and if the grout does not blend well with the tiles it can create a less than professional looking finish. In addition, the grout can easily become soiled and over time and will detract from the look of tile its self. (including carriage)

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 300 x 330 mm as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement: 4 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete. (including carriage)

Coloured Granite stone tiles 20 mm thick in skirting, risers of steps dado, walls and pillars laid in 12.5 mm thick cement mortar 1:3 (1 cement, 3 coarse sand) and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing & polishing including labour for fixing dowels, pins and cramps (including carriage)

Sub Head-5 : Water Cooler Supply & installation of AQUA FLO DX UV Water purification system, capacity 60 'tr. Per hour, 100% chemical free, Dimension 210mm width x 140 mm depth x 382 mm height, in built voltage stabilizer, Hi Flo, Dual Cartridge including installation etc. Complete in all respect as approved and desired by the Engineer-in-charge at site.

SUB WORK-2 : ESTATE WATER SUPPLY Excavation by mechanical means(JCB or Hydraulic excavator) in trenches for pipe lines with straight or open cutting in streets or open area including tri mm ing and dressing sides levelling of beds of trenches to correct grade, cutting joint holes, refilling consolidation, watering , including the cost of dewatering of rain water, diversion for traffic, night signals. providing & fixing caution boards, crossing over trenches for access to the houses, watching, fencing, etc. and removal of surplus soil out side/inside the town involving lead up to 15 meter complete in all respect.

Earth work up to 1.5 m. Depth for

All classes of soil except rocky

For 50 mm pipe line

Providing and laying, jointing, fixing, testing ISI Marked G.I. Pipe (as per IS 1239) B- Class, including cost of Specials such as tees, bends, sockets elbow etc., cutting, threading and testing in trenches in the ground complete.

Cement Concrete 1:6:12 with 40 mm gauge stone aggregate using concrete mixer (including carriage)

For Covering G.I. Pipe

Providing, fixing and jointing G.I Union Couplings (of approved make with the approval of EIC) as per IS 1879 in G.I. Pipe lines complete in all respect.

50 mm i/d G.I. Union

Providing, fixing and jointing ISI Marked Gun-Metal peet valves (Heavy Pattern) as per IS 778 with hand wheels, on G.I. Pipe lines laid in the ground or inside buildings including all carriages complete.

50 mm i/d Gun Metal peet valve heavy pattern.

Providing ISI Marked G.M ferrule as per IS:2692, drilling and tapping cast iron pipe lines of all diameters and screwing in Ferrule and connections complete in all respect.

25 mm i/d Ferrule heavy duty

SUB WORK-3 : ESTATE SEWERAGE Providing, laying in trenches to correct gradient and alignment and jointing of UPVC pipes having ISI specification IS:15328-2003 class-SN-8 marked good on them and laying the same in trenches to correct alignment and gradients, cutting and jointing, testing for water tightness and making good the leakages and defects including cost of specials (Specials and Solvent should be of same make as that of pipes) complete in all respects.

110 mm o/d pipes

160 mm o/d pipes

Excavation in trenches with straight or open cutting in streets, lanes or in open area with 3D/JCB or excavator including manually dressing bed, tri mm ing sides and side slopes for sewers and manholes to full depths as shown in drawings, including, dressing to correct sections and dewatering, provision for diversion for traffic, protection of existing services i.e. telephone cables, electric lines, water supply lines and gas lines etc. night signals, profiles, pegs, sight rails, boning rods, watching, etc., fixing and maintenance of caution boards, fencing, refilling trenches, watering, ra mm ing and restoration of surface to original level and removal of surplus spoil from the site of works, up to one chain (15 m) complete in all respects. For depth exceeding 3.0 m but not exceeding 4.5 m B.G.L. For Sewer line 160 mm dia

Cement Concrete 1:6:12 with 40 mm gauge stone aggregate using concrete mixer (including carriage) For covering Sewer Line type II

For Sewer line 110,160 mm o/d (Type-II)

Constructing brick masonry mainhole in cement motor 1:5(1 cement: 5 course sand) R.C.C. Top Slab 20 cm thick using m-20 mix by using mixer and vibrator TMT fe 500@ 63.464 Kg/P/Cum, foundation concrete 1:4:8 mix (Cement: 4, Course Sand: 8 granded stone agreegate 40 mm nominal size) inside plastering 12 mm thick benching in cement concrete 1:2:4)1 Cement:2 Course Sand: 4 Graded Stone agreegate 20mm nominal size ) finished with a floating coat of neat cement, orange colored PVC steps including RCC cover with frame complete as per standard design complete in all respect. 2 No. manhole size 75x120 cm for Sewer Line quantity as bellow:-

Inside size 75x120 cm with depth 120 cm between bottom of top slab and invert (with manhole cover & frame medium duty) including extra depth

Cement Concrete 1:4:8 with stone blast 40 mm guage using concrete mixing volumatrictype including Carriage+MPS

First Class brunt brick woek laid in cement sand mortar 1:5 in foundation and plinth including Carriage.

Cement Concrete 1:2:4 (1 Cement:2 Course Sand :4 Graded Stone agreegate 20 mm nominal size) for benching.

Floating coat on benching

12.5 mm thick Cement Plaster 1:3 and Cement rendring on plaster 1 mm thick including Carriage

Reinforced Cement Concrete M-20 mechenically batch mixed using batch type concrete mixture as per IS 1791 and vibrated by needal vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth including Carriage.

Cold twisted deformed (Ribbed/ Tor Steel Bar/TMT) Bars Fee 500 grade as per IS 1786-2008, for R.C.C works, where not including in the complete rate of RCC including bending and placing in position complete. MPS + RWHS

Providing orange colour safty foot rest of minimum 6 mm thick plastic encapsulated as per IS 10910 on 12 mm dia steel bar confirming to IS 1786 having minimum cross section as 23 mmx 25 mm and overall minimum length 263 mm and width as 166 mm with minimum 112 mm space between protruded legs having 2 mm thread on top surface by ribbing or chequering beides necessary adiquates ensuring protection on tail length on 138 mm as per standard drawing and suitable to withstand the bend test and chemical resistant test as per specification and having manufactures permanent identification mark to be visible even after fixing, including fixing in manhole with 230 x 150 x 75 cm cement concrete block 1:2:4(1 Cement: 2 Sand: 4 stone aggregate) Complete as per design

providing and fixing 560 mm 500 mm and 450 mm internal diameter circular or 450 mm x 600 mm clear inside opening rectangular RCC manhole cover and frame ISI marked as per IS 12592-2002 including carriage from the store of the Engineer-in-charge to site of work, loading, unloading including stacking and setting the same to correct lines over manhole including cement concrete coaping (M-20) around the same etc. dia of steel for lifting hook is 16 mm (For EHD & HD)

560 mm i/d RCC ,manhole cover with frame Medium Duty

Extra for making connections of all sizes newly laid sewers within benching of fully charged sewers including plugging of sewer, dewatering & desilting of manholes etc. complete in all respects.

with existing sewer of 300 mm id and below.

SUB WORK-5 : FIRE FIGHTING EQUIPMENT Providing and fixing of FIRE EXTINGUISHER, CO2 type as per IS: 15683 complete with all accessories as per Manufactures Specification. ISI Mark complete in all respect.

4.5 Kg. Capacity

Providing and fixing of FIRE EXTINGUISHER, ABC Powder type (stored pressure) as per IS: 15683 complete with all accessories as per Manufactures Specification. ISI Mark complete in all respect.

6 Kg. Capacity

Providing Internal Electrical installations

RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES:

Wiring in PVC insulated copper conductor single core FR cable (ISI marked), 1100volts grade to be laid in heavy gauge, uPVC, fire retardant conduit pipe 20mm/25mm dia. (2mm thick) ISI Marked, recessed in wall etc., complete with powder coated/anodized concealed metal boxes required for suitable number of modules, for having electronic fan regulators, bell push, electronic buzzer, 3pin 6Amp., 3pin 16/20Amp. Sockets and 6Amp./16/20Amp. Switches and covered with brown backelite white glazed translucent backside painted sheet 3mm thick etc. & including the cost of flush piano type. switches/sockets, step type electronic fan regulator 100watts, PVC connector (For Fan Box and Electronic Buzzer), Steel Hooks, Circular Inspection Box (Recessed Type and Deep Type) conduit pipe & copper wire and other petty material etc. including the cost of cutting and filling up of chases:-

Wiring fan point with sheet metal fan box (shape hexagonal) in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5 sq. mm, 1100volts grade with step type electronic fan regulator 100watts.

Wiring light point in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5 sq. mm, 1100volts grade.

Wiring 3 pin 6 Amp. wall socket (Shuttered) point in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5 sq. mm, 1100volts grade complete with bonding to existing earth with PVC insulated copper conductor single core FR cable (ISI marked) overall 1 sq. mm, 1100volts grade.

Wiring 3 Pin 6 Amp. Plug control comprising wall socket (shuttered) and switch including bonding to existing earth with PVC insulated copper conductor single core FR cable (ISI marked) overall 1 sq. mm, 1100volts grade complete.

Wiring 3 pin 16/20 amp. power plug control (shuttered) and switch.

Wiring call-bell point in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5 sq. mm, 1100volts grade with bell push and electronic buzzer 230 volts AC (including the cost of bell push, electronic buzzer & powder coated concealed metal box for electronic buzzer).

PVC, HDPE PIPES & PVC FLEXIBLE PIPES: Supply & erection of PVC pipes & HDPE pipes (fire retardant) for wiring purposes including bends, inspection boxes etc., where necessary including other petty material as per PWD General Specifications 2010

Heavy gauge PVC conduit pipe 20mm dia. (ISI marked) Flushed

Heavy gauge PVC conduit pipe 25mm dia. (ISI marked) Flushed

Heavy gauge PVC conduit pipe 40mm dia. (ISI marked) Flushed

Supply and erection of PVC flexible pipe complete with compression glands, having locking arrangement, check-nuts as required :- PVC flexible pipe 40mm dia.

HEAVY GUAGE WELDED CONDUIT PIPES: Supply and erection of 20mm dia. heavy gauge welded conduit pipe (1.60mm thick) suspension rod for ceiling fan complete in all respect as desired by the Engineer-incharge.

PVC INSULATED SINGLE CORE FR COPPER CONDUCTOR CABLE:

Supply and erection of PVC insulated single core FR copper conductor cable ISI marked left bare in pipe or casing of suitable size excluding the cost of supply and erection of pipe or casing.

PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5 sq.mm, 1100volts grade

PVC insulated copper conductor single core FR cable (ISI marked) overall 2.5 sq.mm, 1100volts grade

PVC insulated copper conductor single core FR cable (ISI marked) overall 4 sq.mm, 1100volts grade

PVC insulated copper conductor single core FR cable (ISI marked) overall 16 sq.mm, 1100volts grade

COPPER EARTHING : Earthing of Sheet metal/ iron clad switches and metallic cases etc., with 8 SWG (4mm dia.) electrolytic copper wire thimbled (with 1 nos. copper thimble) to 30 cm x 60 cm x 3 mm thick tinned copper plate (made cylindrical) burried 10 metre below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the copper wire run through 20mm dia. G.I. pipe (A-Class) on wall and in floor etc., up to 13 metre in length (including bore length). G.I. pipe 20mm dia. (A-class) should be laid in the hole of excavation from bore surface level to 1 feet below ground level and having wire mesh funnel fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm around the hole of excavation.

Supply and Erection of 8 SWG 4mm dia copper wire run through 20mm dia. Heavy guage welded conduit pipe (As additional length).

SWITCH DISCONNECTOR FUSE UNIT (With Sheet Enclosure):

Supply and erection of Switch Disconnector fuse unit with HRC Fuses in sheet enclosure on the existing surface (conforms to IS 13947 (PartI&III) complete with G.I. Bolts, Nuts etc. according to the size of holes in the body of the enclosure & Connection on both sides of switch with sutiable size of Thimbles, including cost of HRC fuses as per PWD General Specifications (Electrical Works).

63Amp. 415volts three pole & neutral switch disconnector fuse unit with HRC Fuses in sheet enclosure

SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB/ RCBO/ RCCB's: Supply and erection of sheet metal double door distribution boards of suitable size and of required no. of ways for mounting miniature circuit breakers/ RCBO's/ RCCB's in the existing MCB distribution board as per PWD General Specifications 2010 including connections with suitable size of thimbles and bonding to existing earth etc.

GROUP-A: (Siemens (Beta Guard/Minigard), Legrand (Ekinoxe) & Schneider (Neo Break), L&T (EXORA), HAGER

Sheet metal double door T.P. & N. distribution board (dust protected) provided with bus bar, neutral link and din bar, suitable for incorporating FP/ TPN MCB's/ isolators for incoming and DP/ SP & N/ Single Pole MCB's/ RCBO/RCCB's for outgoing 8 way each

GROUP-B: (Havell's, HPL, ABB, Standard & other brands approved by PWD)

Sheet metal plug and socket distribution board single pole MCB and neutral enclosure with a two pin and earth plug socket to incorporate in one single pole MCB 20amp.

MINIATURE CIRCUIT BREAKERS/ RCBO's/ RCCB's: Supply and erection of Miniature Circuit Breakers/ RCBO's/ RCCB's in the existing MCB distribution board as per PWD General Specifications 2010 including connections with suitable size of thimbles/lugs. GROUP-A: (Siemens (Beta Guard), Legrand (Lexic) & Schneider (Neo Break), L&T (Exora,Hager)

Miniature circuit breaker single pole 6 to 32amp. (Breaking capacity 10kA, Curve-C) suitable for 240/ 415 volts 50cycles AC supply

Miniature circuit breaker four pole 50, 63amp. (Breaking capacity 10kA, Curve-C) suitable for 240/ 415 volts 50cycles AC supply

DOUBLE WALLED CORRUGATED (DWC) HDPE PIPES: Supply and erection of double walled corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation (making necessary trench), placing the pipe in position and back filling with excavated soil etc. of the required size.

Double walled corrugated (DWC) HDPE pipe 63/ 51mm (outer/ inner dia.)

Supply and erection of High quality aluminium extruded with decorative end caps glazed LED batten including erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer in-charge at site.

S/E of Energy Saving Fan Ceiling Fans 1200 mm sweep ( 48" ) having two ball bearing but without regulator including flexible wire & petty material etc. for connections complete with erection, connections and testing etc. complete in all respect as approved and desired by the Engineer-in-charge at site.

Supply and erection of 12" Heavy Duty Exhaust fan (HDEF) (300mm-900RPM) Single Phase of heavy duty motor with die cast Aluminium rotor mounted on two ball bearing including erection, connections and testing etc. complete with flexible wire and petty material reqd. for connections and louver shutter complete in all respectsas appd.and desired by the Engineer in-charge at site

Supply and erection of Plastic Ventialtion Fan Ventilus 10" (250 mm - 900 RPM) single Phase including erection, connections and testing etc. complete with flexible wire and petty material regd. for connections and louver shutter complete in all respects as approved and desired by the Engineer in-charge at site

Supply and erection of Wall fan of 400mm sweep (16") High Speed. heavy duty motor with die cast Aluminium rotor mounted on two ball bearing including erection, connections and testing etc. complete with flexible wire and petty material reqd. for connections and Aluminium louver shutter complete in all respects as appd. and desired by the Engineer in-charge at site.

Supply and erection of Glazed LED Batten Hgh Qualty Aluminium Extruded with decorative end caps including erection of the same with connections, testing etc.complete in all respects as approved and desired by the Engineer In-charge at site.

Supply and Erection of Recess mounted white powder coated CRCA housing with Window acrylic diffuser LED Panel 2' x 2' 36 w including cutting of ceiling, erection, connections and testing etc. of the same with petty material as required at site complete in all respects as approved and desired by the Engineer in charge at site.

Supply and Erection of Neve Plus (Square) LED recess mounte square pannel with aluminium die cast housing with cut out dimensions of 206 mm x 206 mm incuding cutting of ceiling, erection, connections and testing etc of the same on wall with petty material as required at site complete in all respects as approved & desired by the Engineer-in-Charge.

Supply & erection of Computer Terminal suitable for Computer Networking with modular accessories one on. metal box 12 module 8" x 6", 3 Nos. Switch 6 Amp, 3 Nos. Socket 3 pin 16 Amp, 1 No. Switch 20 Amp, 1 Nos. Socket 20 Amp and 1 No. Modular Accessories including connections & testing complete in all respect as desired by the Engineer-In-Charge at site.

XLPE/ PVC INSULATED UN-ARMOURED CABLES (LOOSE IN THE EXISTING TRENCH OR PIPE): Supply and laying of XLPE/ P.V.C. insulated P.V.C. sheathed aluminium conductor un-armoured cable working voltage upto and including 1100 volts grade to be laid loose in the existing trench or pipe as per PWD General Specifications 2010:-

XLPE/ PVC insulated PVC sheathed aluminium conductor unarmoured cable working voltage 1100volts grade 35sq.mm (3 ½ Core)

Supply & Erection of LED Street Light 45w in aluminium pressure Die Cast housing with touched glass cover (IP 66 protection ) including erection of the same with the existing bracket fixed with pole, connections and testing etc. complete in all respects as aproved by the Engineer in charge at site.

GI PIPE POLE BRACKETS: SINGLE ARM BRACKETS: Supply and erection of G.I. pipe 40mm dia. (A-class) single arm bracket atleast 1 metre long arm to give a total overhang at a tentative angle of 100/105º, the bracket should be fixed on the top of the GI pipe pole having top outer dia. 80mm with GI reducer 80mm x 40mm with two coats of an approved aluminium paint complete in all respect as approved by the Engineer-in-charge at site.

SUPPLY AND ERECTION OF WIRING ACCESSORIES: Supply and erection of switches, sockets, power switch and sockets and other accessories (flush piano type/ modular accessories) in the existing bakelite/ modular cover frame including connections and petty material etc.

Bakelite batten holder large size

LAN (Data Cabling and Computer Networking)

Supply, erection Testing and Commissioning of CAT6 UTP Networking Cable of 10/100/1000 Mbps DCC in existing PVC conduit complete In all respect as desired by the engineer in charge at site. Make complete in all respects as approved and desired by the Engineer In charge at site.

Supply & erection of CAT 6 ONE Meter long Patch Cord Having RJ-45 Male Connectors on both ends DCC up-to 10/100/1000 mbps. complete in all respects as per satisfaction of the Engineer-in-Charge

Supply & erection of CAT 6 TWO Meter long Patch Cord Having RJ-45 Male Connectors on both ends DCC up-to 10/100/1000 mbps. complete in all respects as per satisfaction of the Engineer-in-Charge

Supply & erection of CAT 6 Information Outlet (I/O) with 3" x 3" Polycarbonate face plate for termination of Networking Cable. complete in all respects as per satisfaction of the Engineer-in-Charge

Supply & erection of CAT6, 24 Port Fully loaded Patch Panel, Rack Mountable for cable termination. Make: complete in all respects as per satisfaction of the Engineer-in-Charge

Supply & erection of 9U Wall mount 19" Rack with glass door, lock & key facility 450mm 550mm depth. with CPD, Cable Manager complete in all respects as per satisfaction of the Engineer-in-Charge

Supply & erection of 24 Port manageable 10/100/1000 Mbps Layer 2 Data switch with 2 Combo 1 Gbps copper & SFP Port complete in all respects as per satisfaction of the Engineer-in-Charge

Supply & erection of 800VA LIT sine wave UPS/ Power Plant with 2 SMF batteries having 30 Minutes backup time. complete in all respects as per satisfaction of the Engineer-in-Charge

Supply & erection of 25 mm 151 marked PVC channel on wall surface. complete in all respects as approved and desired by the Engineer in charge at site.

Supply & erection of 45mm x 45 mm Cable Management Tray slotted Gray Colour 151 marked PVC on wall surface. complete in all respects as approved and desired by the Engineer in charge at site.

PVC, HDPE PIPES & PVC FLEXIBLE PIPES: Supply & erection of PVC pipes & HDPE pipes (fire retardant) for wiring purposes including bends, inspection boxes etc., where necessary including other petty material as per PWD General Specifications (Electrical Works):-

Heavy gauge PVC conduit pipe 25mm dia. Flushed

EPABX System Supply & Erection of Digital EPBX System 100% Non-Blocking, Auto Attendant, CLI, 3 Party Conferences Configured for 04 Trunk & 12 Normal Extensions. 12VDC Power Supply Adaptor complete in all respects as per satisfaction of the Engineer-in-Charge

Supply & Erection of 20 Pairs MDF + 20 Pair IDF with Krone Modules & Lockable Box complete in all respect. as per satisfaction of the Engineer-in-Charge

Supply & Erection of Basic Wired Telephone with Display, Redial, CLIP & Mute Compatible with EPABX System. complete in all respects as per satisfaction of the Engineer-in-Charge.

Supply & Erection of Featured Wired Telephone with Blue Backlit Display, Redial, CLIP, 2 Way Speaker, Calculator, Mute Compatible with EPABX System.complete in all respects as per satisfaction of the Engineer-in-Charge

Supply & Erection of 02 Pair 0.5mm PVC Dual sheathed Telephone Cable as per ITD Specification with Up to amendments. complete in all respects as per satisfaction of the Engineer-in-Charge

Supply & Erection of RJ-11 Telephone Socket With 3" x 3" size Polycarbonate face plate complete in all respect. as per satisfaction of the Engineer-in-Charge

Supply & erection of 25 mm ISI marked PVC channel on wall surface. complete in all respects as approved and desired by the Engineer in charge at site.

Copper Earthing : Earthing of Sheet metal/ iron clad switches and metallic cases etc., with 8 SWG (4mm dia.) electrolytic copper wire thimbled (with 1 nos. copper thimble) to 30 cm x 60 cm x 3 mm thick tinned copper plate (made cylindrical) burried 10 metre below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the copper wire run through 20mm dia. G.I. pipe (A-Class) on wall and in floor etc., up to 13 metre in length (including bore length). G.I. pipe 20mm dia. (A-class) should be laid in the hole of excavation from bore surface level to 1 feet below ground level and having wire mesh funnel fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm around the hole of excavation.

PVC, HDPE PIPES & PVC FLEXIBLE PIPES: Supply & erection of PVC pipes & HDPE pipes (fire retardant) for wiring purposes including bends, inspection boxes etc., where necessary including other petty material as per PWD General Specifications (Electrical Works) :-

Heavy gauge PVC conduit pipe 25mm dia. Flushed

Supply, Erection, Testing and Successful Commissioning of Diesel Generating Set 20 K.W./ 25 KVA

Supply, Erection. Testing and Commissioning of 25 KVA /20 Kw Diesel Generator set with silent canopy without AMF panel comprising of 0.8 Power Factor. 3 Phase 415 V, 50 HZ, 1500 RPM 42 bhp, electric Start 3 Cylinder 4 stroke Cycle, Water cooled Turbo charged aspirated complete with flywheel with starter ring for Generating Set. Air Fillter, Lube oil cooler assembly with accessories, Exhaust air manifold, Exhaust Silencer, Expansion bellow, fuel filter . Lube oil filter . exhaust gas tubocharged after cooled, Radiator with pusher type fan, with fan guard . coolant pump , 12 V electrical starting system with starter motor and battery charging alternator. Fuel Injection Pump with Electronic Governor and fuel feed pump. Engine control panel - Microprocessor based controller, Engine Mounting supports, Safeties and Indications against Low Lube Oil Pressure and High coolant tempreture etc. K Cool super plus corrosion inhibitor coolant for cooling and coupled with 200 KVA Alternator engine with sound proof accoustc enclosure , Echo Friendly ( CPCB-II norms compliance) complete with all accessories. The Generator set should be installed at site on the suitable size plinth of RCC as per specification including making of plinth for DG set as per satisfaction of the Engineer-In-Charge at site. The model of Engine will be decided by the Engineer in Charge.

XLPE/ PVC INSULATED ARMOURED CABLES (LOOSE): Supply & laying of aluminium conductor XLPE/ P.V.C. insulated armoured and served cable to be laid loose in the existing trench or pipe as per PWD General Specifications 2010.

Aluminium conductor XLPE/ PVC insulated PVC sheathed armoured and served cable working voltage 1100volts grade 50sq.mm (3 ½ Core)

COPPER EARTHING : Earthing of Sheet metal/ iron clad switches and metallic cases etc., with 8 SWG (4mm dia.) electrolytic copper wire thimbled (with 1 nos. copper thimble) to 30 cm x 60 cm x 3 mm thick tinned copper plate (made cylindrical) burried 10 metre below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the copper wire run through 20mm dia. G.I. pipe (A-Class) on wall and in floor etc., up to 13 metre in length (including bore length). G.I. pipe 20mm dia. (A-class) should be laid in the hole of excavation from bore surface level to 1 feet below ground level and having wire mesh funnel fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm around the hole of excavation.

Supply and Erection of 8 SWG 4mm dia copper wire run through 20mm dia. Heavy guage welded conduit pipe (As additional length).

DOUBLE WALLED CORRUGATED (DWC) HDPE PIPES: Supply and erection of double walled corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation (making necessary trench), placing the pipe in position and back filling with excavated soil etc. of the required size.

Double walled corrugated (DWC) HDPE pipe90/76mm (outer/ inner dia.)

SHEET METAL IRON CLAD CHANGEOVER SWITCHES: Supply and erection of sheet metal iron clad change–over switch on existing surface with G.I. bolts & nuts / rag bolts and nuts etc., according to the size of holes in the body of the switch including connectiions with suitable size of thimbles and bonding to the existing earth as per PWD General Specifications

Sheet metal iron clad double pole changeover switch 100amp. 415 volts

Enviornmental Management Making lawns including ploughing & dragging with 'Sohaga' breaking of clods, removal of earth rubbish dressing & Supplying doob grass roots and planting at 15 cm. apart including Supplying and spreading of farm yard manure@ 0.18 cum per 100 sqm & loosening.

Supplying and planting permanent trees including digging of earth pits size 75cmx75cmx75 cm deep, refilling the excavated earth with manure supplied @ 0.113 cum each and watering Supplying through tractor tanker. (Trees like Neem, Ashoka, Dake, Arjun etc.)

Planting ground cover plants including digging and refilling of beds with excavated soil and FYM, Fertilizer and insecticides, planting of saplings at 30cm distance from plant to plant and row to row, providing and fixing brick tiles edging.

Planting flower beds including digging and refilling of beds with excavated soil and FYM, fertilizer and insecticides, planting of sapling at 30cm distance from plant to plant and row to row.

Provision for one way stand post with Khura complete in all respects