Construction of Main Entry Junction and Construction of Gate House at IFP Chanalon

Excavation for Roadway

Excavation in Soil (any type) using Hydraulic Excavator CK 90 with hydraulic excavator of 0.9 cum bucket capacity including cutting, trimming bottom and side slopes, in accordance with equirements of lines, grades and cross sections,including all lifts and combined lead upto 30m.

Compaction of earth work & preparation of sub grade including loosening, leveling of earth 225mm thick top layer, rough dressing of soil, final dressing of earth to give level, camber, watering, rolling with road roller, compacting the bed to achieve minimum dry density as given in table 300-2 as per technical clause 305 of MORT&H specifications.

Granular Sub-Base (Coarse Graded Material Grading-II) Construction of granular sub-base by providing material as per grading-III ( Table 400-I of MORT&H 5th revision), mixing in a mechanical mix plant at OMC, carriage to site spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per technical clause 401 of MORT&H specifications

Construction of dry lean cement concrete Subbase over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, carriage to site & aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg / cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site with transit mixer , laid with a paver with electronic sensor, compacting with 8- 10 tonnes vibratory roller, finishing & curing.

Plain Cement Concrete Pavement

Construction of un-reinforced M-40 grade concrete pavement with dowel jointed over a prepared sub base with 43 grade OPC cement of concrete, coarse & fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a fully computerised batch mix plant as per approved mix design, transported to site in transit mixer with lead up to site. laid with a fixed form or slip form paver, spread, compacted & finished in a continuous operation including provision of contraction, expansion, construction & longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, admixtures as approved, curing compound, finishing to lines & grades as per clause 602 of MORT&H 5th Revision

Reinforcement

Mild steel requirement for RCC work where not including the complete rate of RCC including bending, binding and placing in position complete in all respects.

Above 20mm dia bars

Cold twisted detormed (Ribbed/ Tor steel) Bars (Fe 500 grade as per IS 1786-2008) , for R.C.C works, where not including in the complete rate of RCC including bending and binding placing in position complete

Road marking with hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads @ 0.25kg per sqm area as per IRC:35 1997 complete as per technical clause 803 of MORT&H specifications

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage to site laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density complete as per technical clause 406 of MORT&H specifications

Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M-35 grade machine made rubber moulded smooth finish with strong vibratory process or with vibrohydraulic compaction machine and of approved size and design / shape laid in Ordinary Grey and pattern over and including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer-in-Charge . IS Code: 15658 (2006)

Construction of cement concrete Kerb with top and bottom width 115 and 165 mm respectively, 300 mm high in M 20 grade Kerb stone laid with Kerb laying machine, all complete as per clause 408

Painting two coats excluding priming coat with Synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade.

GATE HOUSE

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 meters including removal and disposal of top organic soil not exceeding 150 mm in thickness as per technical clause 201 of MORT&H specifications

In area of Light Jungle (By Mechanical Means)

Earth work in excavation in foundations, trenches etc. in all kinds of soil where pick jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and sebsequent filling around masonery in 15 CM layers with compaction including disposal of surplus soil as directed with in a lead of 30 meters

Cement concrete 1:4:8 with stone ballast 40mm gauge.

40mm gauge using concrete mixer volumetric type.

Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering)

Centring and shuttering for columns (Square or rectangular or poly gonal in plain)

Reinforced cement concrete M-25 mechancially batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth

Reinforced cement concrete M-25 mechancially batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering above plinth level

First class burnt brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level.

First class burnt brick work laid in cement sand mortar 1:5 in foundation and plinth

12.5 mm thick cement plaster 1:4

Cold twisted deformed (Ribbed/ Tor Steel Bar) Bars Fe 500 grade as per IS 1786-1985, for R.C.C works, where not including in the complete rate of RCC including bending and placing in position complete

Providing and laying Polished Granite stone 18 mm thick flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :

Crazy marble stone flooring, including filling the gaps with light shade pigment with white cement marble powder mixture (3 parts of white cement : 1 part of marble powder) by weight in proportion of 4:7 (4 cement marble powder mix : 7 white, black or white and black marble chips of sizes from 1 mm to 4 mm nominal size by volume), with under layer 25 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size), including rubbing, polishing and cement slurry etc. complete : 11.15.1 18 mm thick crazy marble stone white, black or as specified.

Providing and fixing 4"x4"x4" size stone Granite/basalt cobblestone of approved color with flooring of 20 mm bed of cement sand mortor 1:3 complete in all respect.

Providing and fixing thick white Pables stone /boulders of size upto 18 kg fixing with MS wire in vertical surface cement sand mortor 1:3 complete in all respect to entire satisfaction of engineer -in charge

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish

Finishing walls with acrylic smooth exterior paint of required shade with two or more coats applied @ 1.67 litre/10Sqm over and including base coat of water proofing Cement Paint applied @ 2.20 Kg/10 Sqm.

Construction of embankment with good quality earth obtained from borrow pits including compensation of earth, loading, unloading, carriage to site of work, spreading, grading to required slope and compacting to meet requirement of table 300-2 as per technical clause 305 of MORT&H specifications including compensation for earth taken from pvt land and carriage upto site of work complete in all respect.

Providing & Fixing of hoarding with 3D SS letter of approved size and shape as para drawing (in English and Punjabi) including backlid led light as per drawings/specification complete in all respect to entire satisfaction of Engineer in charge.

Supplying and fixing of GI sheet frames (Chowkat) consisting of 18gauge (1.25mm) thick steel sheet of the specified section (standard designlatest), includingironlugs(holdfasts) iron hinges conforming to PWD specifications including bolts for fixing steps, lock notch provision for receiving tower boltsand finished, fixed in position including the cost of cement concrete1:3:6for fillingintheframeandcement concrete 1:2:4 for lugs complete to the satisfaction of Engineer-in-charge.

Doors and windows frame of size 118mm x 60mm with 40 mm wide single rebate weighing 3.43 kg per meter.

Doors and windows frame of size 161mm x 60mm with 40 mm wide double rebate weighing 4.05 kg per meter.

Providing and fixing 14 gauge MS sheet garage doors with 40mmx40mmx6mm angle iron frame with diagonal braces 3.15mm gusset plates including locking arrangement with handles etc.complete in respects

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with PVC Plug/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminum snap beading shall be paid in basic item)

Float glass panes of 5 mm thickness

Providing and fixing aluminum Wire Mesh including cost of necessary fittings i.e.screws,u Type Beading etc. complete

Providing & fixing 110 mm dia U.P.V.C Rain water pipe of 4 kgf./sqm as per IS: 4985 including jointing during masonary complete as per specifications & to the entire satisfaction of Engineer-in-charge.

Providing & fixing 150 X 10 mm anodized aluminum Mat Finish tower bolts ISI marked on door & window frames complete in all respect as per the directions of Engineer-in-charge.

Providing & fixing 75mm with Plate 125mm X 32 mm anodized aluminum Mat Finish handles ISI marked on door & window frames complete in all respect as per the directions of Engineer-in-charge.

Supplying and stacking at site of work well decayed farm yard manure from approved site of work including screening through sieve of I.S. designation 16 mm with 5 km lead.

Fine grassing including uprooting rank vegetation and weeds by digging the area to a depth of 30 cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growth after 10 to 15 days, mixing fertilizer and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts, watering, weeding and maintenance for 30 days or till thick lawn is formed.

Steel work in built up tubular pipes (round, square or rectangular hollow tubes etc. ISI Marked) for flat shed (ie.Where no truss work is involved) including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washer etc complete having span:- upto 15mtr span.

Providing and fixing M.S.Jali of approved design in steel structure including cost of necessary fittings i.e.screws,u Type Beading etc. complete in all respect.

Applying priming coat with metal primer on new steel or iron work including preparation of surface.

Painting two or more coats excluding priming coat with Duco paint with compressor in all shades on wood work, metallic or plastered, concrete surface to give an even shade as per approved drawings complete in all respect to the entire satisfaction of Engineer in charge.

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminum doors including necessary cutting and making good etc. complete.

Top khurra 0.6m x 0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50mm thick cement concrete 1:8:16

Bottom Khurra on ground 1.2 m x 0.6 m consisting of brick on-edge laid in cement mortar 1:3 over 75 mm cement concrete 1:8:16 including 12.5 mm thick cement plaster 1:3

Cement concrete 1:2:4 gola 10 cm x 10 cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified

Making plinth protection Conglomerate floor 40 mm thick cement concrete rate 1:2:4 on 100 mm thick cement concrete 1:8:16 with stone aggregate 40mm gauge & 100 mm sand filling using mechanical mixer for mixing material.

Base course of floor consisting of 100mm thick cement concrete 1:8:16 with stone aggregate 40mm gauge and 100mm fine sand filling (Using mechanical mixer for mixing material)

Conglomerate floor 40mm thick cement concrete topping 1:2:4. (Using mechanical mixer for mixing material)

ELECTRICAL

Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia. (ISI Marked) recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16 / 20Amp. combined / universal Socket (shuttered), 6 /10Amp. Switches, 16 / 20 Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), Circular junction Boxes (Four way PVC 1½" deep for walls and CI 3" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material tc., including the cost of above material, cutting and filling up of chases (with finishing the surface):-

Wiring fan point (With fan box)

Wiring light point in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5 sq. mm, 1100volts grade.

Wiring 6Amp. Plug control comprising wall socket point

Wiring 16 / 20Amp. power plug control point

Providing, installation testing and commissioning of following Luminaires, Ceiling Fans & Exhaust fans. (The sample shall have to be got approved from Engineer-in Charge.

Supply, test, intall and commisioning 48" (1200mm) ceiling fan with double ball bearing off white complete with petty material for connection as per satisfaction of Engineer-in-charge of make Havells model Velocity/Orient new breeze/ Crompton high speed (Reveria)

Supply erection testing and commisioning of 9 watt LED bulb completeofin all respect entire satisfaction of Engineer in charge.

Supply, erection, testing & commissi-oning Highly durable surface mounted LED batten constructed of fire retardant engineering grade extruded plastic & decorative end caps of 18 / 20 watt complete in all respects to the entire satisfaction of engineer incharge of cat no. BN021C LED20S PSU NW GR / CDL GR of Philips or cat no. LCTL-18-CDL of Crompton Greaves or cat no. LHLDCLXENL 8 X 018 complete of Havels make.

MINIATURE CIRCUIT BREAKERS/ RCBO's/ RCCB's:

Supply and erection of Miniature Circuit Breakers/ RCBO's/ RCCB's in the existing MCB distribution board as per PWD General Specifications 2010 including connections with suitable size of thimbles/lugs.

Miniature circuit breaker single pole 6 to 32amp. (Breaking capacity 10kA, Curve-C) suitable for 240/ 415 volts 50cycles AC supply.

Providing and fixing of foxus flood light of 30 watt including the cost of M.S cage, painting , priming complete in all respect

Hand boring Horizontly for crossing of pipe under road or any other obstacle by using Auger/Bocki method.Including excavation ,stringing and jointing of pipe upto 160mm complete

Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid (On Surface) as per PWD General Specifications (Overall size 6sq.mm (2core) un-armoured (on-surface)