Upgradation of Kannikapuram Playground, Vyasarpadi

Amount

Providing and constructing cast in situ hydraulic bored piles of specified diameter in M30 grade concrete using blended cement - slag cement with minimum cement content of 400kg/m³ in accordance with the structural engineers drawings and directions, but exculding reinforcement including cost of mobalization of all necessary plants, equipment's like piling rigs, temporary casing of appropriate length for setting out cardinal points and the removal of the same, boring in overburden, using bentonite mud circulation technique or any other method duly through all strata upto the foundation level of piles etc., complete all as approved by the departmental engineer. Further include dewatering, placing concrete by tremie pipe method, disposal of bored material outside the site. Including Chipping carefully cut off portion of piles as required without any damage to the piles and dressing the top and removing all the debris away from the site with out any extra cost as directed including the cost of all tools, plants, conveyance, all labour, lead and lift required etc .,Conducting standard penetration test to identify the refusal strata for atleast 1 pile in group and atleast 25% of piles, comparing with refusal strata as indentified in soil report and providing socketting into refusal strata by 1.00mt or into hard rock by 100% dia of the pile. (Length of pile for payment shall be measured up to bottom of pile cap).

Boring or chiselling through any obstacles, boulders, weathered rock, etc. Upto founding level of piles for seating resting or socketting of files. The rate quoted shall include demobilising the site with all plants, equipment, piling rigs, necessary personnel brought for piling work, including removal and transportation of debrise away as directed, cleaning and reinstating site to original condition as acceptable by the Architect on completion of piling work.

750mm Dia Pile

600mm Dia Pile

500mm Dia Pile

300mm Dia Pile

Carrying out initial Working pile load test on specified dia piles as specified in IS:2911 (Part 4). Includes all plant, equipment, machinery, instruments, measuring devices, platforms and kentledge pile caps etc., dismantling and carting away entire setup, excavation and dewatering etc., all complete.

750mm dia - 500 mm dia - Safe vertical load capacity -95 MT - (for 35 RM )

Carrying out Dynamic Initial vertical load test on Bored cast-in-situ pile as specified in ASTM D4945 for specified test loads.( 750mm dia - 500 mm dia ). Includes all plant, equipment, machinery, instruments, measuring devices, platforms and kentledge pile caps etc., dismantling and carting away entire setup, excavation and dewatering etc., all complete

EARTH WORK

Earth work excavation for all foundations in all type of soils and sub soils to the required depth for Footings, plinth / grade beams, etc,. by mechinaries including manual excavation for the following type of soil / rock as per detailed specification. As per SS 20B as hard rock requiring blasting inclusive of shoring strutting and baling out water wherever necessary and including refilling 0 to 2.0m depth consolidation depositing the surplus earth in places shown clearing and leveling the site with an initial lead of 10 metre and lifts as specified hereunder etc., complete in all respects complying with relevant standard specification and as directed by the departmental officers.

0.0m to 2.0 depth

2.0m to 3.0m depth

3.0m to 4.0m depth

FILLING

Supplying and filling of Gravel / Good Earth by lorry in Foundation basement filling and site filling with approved materials excavation from approved quarries and compacted to meet requirement of table 300-1, 300-2 of MORTH, in layers not exceeding 250 mm loose thickness, spreading, breaking clods, removal of roots and other organic materials to the required line, grade and cross-section including watering, spreading by Dozer, grading by motor grader and consolidation by vibratory road roller with desired field density not less than 95% of maximum dry density ,including all lead,lift, loading, unloading, all labour, hire charges of all machineries, Transportation, etc., complete in accordance with MORTH technical specification clause No. 305 and with all other incidental charges and as per the direction of the Engineer-In-Charge.

Supplying and Filling with M - sand in foundation and others sub structures for 100mm thick and well watered, rammed and consolidated by power compacter. The rate includes the cost of M sand, compacting with mechanical compactors, labour charges for leveling, loading & Unloading and Transportation charges etc., complete and as per the standard specification.

Construction of Granular sub-base of 125mm compacted thickness ( Drainage Layer bottom most) by providing laying, spreading and compacting of Open graded Material conforming to Grading III of Table 400-1 of MORTH clause 401 ,mixing in a Wet Mix Plant of 200 tonne capacity at OMC, carriage of mixed material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory roller 8-10 tonne to achieve the desired density of 98% including protection of edges of GSB layer, cost of all materials, labour, hire charges of machinery, lighting, guarding, barricading, maintenance of diversion road, loading & unloading, all lead and lift etc., to achieve minimum CBR value of 30%(Compacted Thickness) in accordance with MORT&H technical specification clause No. 401 and with all other incidental charges and as per the direction of the Engineer-In-Charge of work.

Construction of Granular sub-base of 125mm compacted thickness by providing laying, spreading and compacting of Close graded Material conforming to Grading V of Table 400-1 of MORTH clause 401 ,mixing in a Wet Mix Plant of 200 tonne capacity at OMC, carriage of mixed material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory roller 8-10 tonne to achieve the desired density of 98% including protection of edges of GSB layer, cost of all materials, labour, hire charges of machinery, lighting, guarding, barricading, maintenance of diversion road, loading & unloading, all lead and lift etc., to achieve minimum CBR value of 30%(Compacted Thickness) in accordance with MORT&H technical specification clause No. 401 and with all other incidental charges and as per the direction of the Engineer-In-Charge of work.

PCC WORK

Providing and laying plain cement concrete 1 : 4 : 8 ratio of (1 cement , 4 sand and 8 graded stone aggregate 40mm nominal size) in foundation and basement including dewatering wherever necessary and laid in layers not more than 15 cm thick and consolidation etc. The rate includes the cost of materials, labour charges, lifting charges, loading & Unloading and Transportation etc., complete and as per the standard specification.

FORM WORK

Supplying and erecting centering for sides and soffits including supports and strutting up to 3.30 m height with all cross bracing for plane surfaces as detailed below, using mild steel sheets of 90 X 60 cm 10 gauge stiffened with MS angle of 25 X 25 X 3mm for boarding, laid over adjustable span & jacks and supported by 50mm dia pipes for general pipes scaffolding systems @ a spacing of 1.20m c/c and vertical connected at a height of 2.0m c/c including 'C' & 'U' clamps and base receiver cup at bottom for connecting pipes etc and removable systems etc., the rate including cost of all materials, labour charges, wastages, placing, transportation, lead & lifts, tools & plants, fuels, fixing in position at all levels, heights, masking tape in sheet joints, consumables, etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

For Column footing, plinth / grade beam, bed blocks, template surfaces, steps, piers, raft slab / beams and such other members

For Vertical surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical walls etc.

for plane surfaces such as rectangular or square rcc columns, sunshades, top and bottom slab of rcc boxing, etc.

For Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

Extra for additional height in centering, shuttering wherever required with adequate bracing, propping etc. including cost of de-shuttering and decentring at all levels. over a height of 3 30 m (height shall be the dimension as measured from the top of the lower slab/pcc sub base to the bottom of the subsequent upper stab) for every additional height of 1m or part thereof for plan area to be measured Suspended floors, nat slabs. drops. post tensioned slabs, slabs curved in plan to any radius, grid slab, rools landings beams including spiral and curved beams of all radius, post tensioned beams, gnd beams, plinth beams. girders, bressumers. cantilevers and balconies. Rate to include all matenals, labour charges, wastages placing. transportation, lead & lifts, tools & plants, fuels, fixing in position at all levels, masking tape in sheet joints, consumables, etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge

Upto 3.0m Height

From 3.0m height to every 1.0m height (or part thereof)

CONCRETE WORKS

Providing and Laying M 30 Design Mix for all reinforced cement concrete with minimum cement content conform to IS 456-2000 using ordinary Portland cement of grade 53 from approved manufacturer, manufactured sand, 20 mm and down graded size coarse aggregates, necessary approved admixtures as per requirement. works for Footings, Grade beam, drain wall & raft , Plinth beams, Column, Grade slab, Roof slab & beam, Column drops, Pergola, Staircase waist and landing slab lintel, Sunshades, parapet Cum drops, Steps, canopy, window boxing slab, Loft, fins facia Planter box, machine foundation, elevation features and other similar structures etc..excluding necessary centering, shuttering and reinforcement which shall be measured and paid separately under relevant items. in-charge

The rate including cost of all designing the mix, batching plant, mechanical mixing, transporting and placing at all levels, leads, lifts, tools & plants, fuels, all materials, labour charges, wastages , laying, pumping the concrete to all levels, providing sleeves / openings in RCC slabs, compaction by vibrator, gunny bags for curing etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge

M - 30 Grade of concrete - below foundation

For Foundation and Basement floors

Column - M - 30 Grade of concrete

For Ground floor

For First Floor

For Second Floor

For Terrace Floor

STEEL REINFORCEMENT

Supplying, fabricating and fixing in position of steel Fe 550 grade Reinforcement for all RCC work with Thermo Mechanically Treated Bars (TMT) conforming to IS 1786 of latest version according to drawings and binding the reinforcement with 18 gauge double fold GI binding wire and providing Concrete cover blocks to maintain the cover as required. The rate including cost of all materials, bending, tying grills, placing, transportation, lead & lifts, tools & plants, fuels, all materials, labour charges, wastages , laying at all levels, fixing in position, cost of cover blocks and GI binding wires etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

MASONARY WORK

Supply and constructing cement concrete solid block masonry work at all levels in cement mortar 1:5 (1 of Cement : 5 of manufactured sand ) using Portland Pozzolana Cement standard size of 400 x 200 mm and 200 mm thick of solid cement concrete with minimum compressive strength of 5 N/Sq.mm.conforming to IS 2185 or equivalent BS and Fly ash conforming to IS : 3812 (Part III)-1966* may be used for part replacement of fine aggregate up to a limit of 20 percent complete and as directed. Concrete blocks manufactured under strict quality control conditions using modern rugged block casting and stripping machine with the latest moulding techniques etc,. only shall be used. The rate including cost of all materials, labour charges, wastages for working at all levels with necessary lead and lifts, transportation charges, loading, unloading, scaffolding, staging, curing, fuel, consumables as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge

For Foundation and Basement. + Ground floor

For Superstructure First floor

For Superstructure Second floor

For Superstructure Terrace floor

Supply and constructing cement concrete solid block masonry work at all levels in cement mortar 1:5 (1 of Cement : 5 of manufactured sand ) using Portland Pozzolana Cement standard size of 400 x 100 x 200 mm of solid cement concrete blocks, with minimum compressive strength of 5 N/Sq.mm.conforming to IS 2185 or equivalent BS and Fly ash conforming to IS : 3812 (Part III)-1966* may be used for part replacement of fine aggregate up to a limit of 20 percent. Concrete blocks manufactured under strict quality control conditions using modern rugged block casting and stripping machine with the latest moulding techniques etc. only shall be used. The rate including cost of all materials, labour charges, wastages for working at all levels with necessary lead and lifts, transportation charges, loading, unloading, scaffolding, staging, curing, fuel, consumables as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

For Superstructure in Ground Floor

For Superstructure First floor

For Superstructure Second floor

JOINERIES

Foamed PVC Door frame : Specification: Providing factory made Pre Laminated FPVC Door Frame of the size 105 X 40mm with a wall thickness of 10mm made out of extruded rigid FPVC profile mitre jointed with 6nos of 5mm long screw. The door frame shall be fixed to the wall by using 80 mm long screws through the frame frame with the help of PVC Fasteners of 3 nos. to be provided for each vertical member, GI stiffners of ( U channel of size 29 X 9, 1mm, 150mm long) - 3 Nos at hinge point, Frame Reinforcement of (U' GI channel of size 46 X 22 X 0.6mm), bottom tie rod of ('U' GI channel Size of 15 X 15 X 1mm ), etc., Complete complying with the standard Specification. the door frame should be got approved from the Executive Engineer before use on work

Providing of 35mm thick factory made pre - laminated ABS ( Acrolynitrile Butadiene Styrene) Door Shutter moulded indifferent desings consisting of all round frame made out of water proof solid PVC bar of size 20 X 32 mm reinforced by 32 X 32 mm 2 nos ., for vertical made out of LVL core material of 32 mm thick high density craft paper honey comb board, sandwiched on both sides with pre- laminated ABS sheets thickness of 1.5mm PVC edge bending of size 0.45mm on the vertical sides. hardware made out of steels coated butterfly hinges - 3nos for each shutter and ISI make SS round lock Complete complying with the standadrd Specification . the door shutter and frame should be got approved from the Departmental Engineer before on use

UPVC Window : Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

UPVC Ventilator : Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability.

The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam .Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.

PLASTERING

Plastering 10 mm thick for ceiling including slabs, beams and column drops and staircase waist slab, sunshade, drops, chajjas etc..with Cement Mortar 1:3 (1 of cement : 3 of P sand) according to the specification. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, providing drip bands, moulds to any size and shape as shown in drawings tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Plastering of 12 mm thick for Internal walls with cement mortar 1:5 (1 of cement : 5 of P sand) according to specifications. Rate shall include for providing GI mesh of nominal thickness at the junctions of masonry and concrete works to a width of 100 to 125mm including tying in position with suitable clamps/screws. The rate including cost of all materials, labour charges, wastages with necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Plastering 15 mm thick for external surfaces with Cement Mortar 1:4 (1 of cement : 4 of P sand) with water proofing compound of “CICO No.1 or equivalent“ as per Manufacturer's Specification with sponge finish (washed sand finish) all complete as per specification and as directed. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, providing drip bands, moulds, grooves to any size and shape as shown in drawings tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

For Superstructure

PAINTING

Supply and painting of two coats of Acrylic emulsion paint of approved shade and colour over one coat of DCP Primer including one coat of Acrylic Wall Putty with DCP Primer. The rate including cost of all materials, brush, roller, ladder, scrapping, washing, materials, labour charges, wastages , cleaning, necessary lead and lifts, scaffolding, stagging, working at all levels, elevations, transportaion charges, loading, unloading, curing, sanding, touchup putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.(Internal surface)

Supplying and painting of 2 coats of weather proof exterior emulsion with high sheen, anti algal properties over one coat wall exterior primer of approved quality and shade etc., complete. The rate including cost of materials, brush, ladder, scrapping, washing, materials, labour charges, wastages , cleaning, necessary lead and lifts, scaffolding, stagging, working at all levels, elevations, transportaion charges, loading, unloading, curing, sanding, touchup putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. ( The make quality and colour of paint should be got approved by the executive Engineer before use on works.)

MS WORK

Providing and fixing welded M.S. grills to the window openings,along the details as per drawing with necessary screws, bolts and fixed with necessary M.S. lugs embedded in masonry with C.C. 1:2:4 and finishing the surface neatly. Rate shall welding and consumables, etc. complete, as directed. Design of grills and the size of members to be used shall be got approval before put into use & as directed by the Engineer-in-charge.

Designing, Providing and fixing in position Hot rolled structural steel Members / Sections consists of MS joists, channels, angles, purlins, pipes, hollow tubes, runners, insert plates, flats etc. at all levels. Surface preparation of all MS members by Sand blasting to SA 21/2 grade and painted with anti corrosive, low VOC PU paint (metallic finish) with compatible primer to a minimum film thickness of 75 microns and 2 coats of low VOC PU paint of Akzonoble make and total dry film thickness 225 microns. (Only Main structural supports related to Facade works if required any shall be considered and no base frame or support structure shall not be considere, which shall form part of the respective cladding and Glazing items). Refer Particular Specification for Mode of measurement for this item. The rate including the cost of all materials,labour,tools,tackle and plants, wastage etc.,as per specification and drawings complete. The rate including cost of bolts, nuts, washers, welding, electrodes and connections required for the work. No extra on this account will be paid for. The rate to include preparation of fabrication shop drawings for departmental engineer-in-charge approval before commencement of work.

Supply & installation of precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm +/- 5% total coated thickness (TCT) thick Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15- 18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. The rate including cost of all materials, labour chanrges, scafolding, stagging, transportation, lead & Lifts, wastage, etc., complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

SS HAND RAILING

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of all materils, Labour charges for cutting, bending, welding, grinding, polishing, Transportation, electrical charges, etc. complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

FLOORING

Providing vaccum de-watered flooring operation consisting of providing side shuttering with MS channels, angles to the required levels, Vibrating the concrete by using screed vibrator, de-watering using vacuum pumps by suction method and finishing the top surface to required level and grade using skim floaters/discs/power trowels. (M30 grade concrete will be paid under relavent item). The above works including for mechanical / power trovelling, Providing with 200 micron thick polythene sheet over the PCC surface,providing and mixing Graded fibrillated 100% virgin poly propelene fibres in concrete at the rate of 0.90 kg/cum as per manufacturers specifications, for providing and mixing non - metallic monolithic surface floor hardening compound in concrete at the rate of 5.0kg/m2 as per manufacturers' specifications and for cutting grooves of size 6mmx10mm at control joints and filling the grooves with Sealent (Colpor - 200 from Fosroc chemicals or Poly sulphide sealant (Pedilite / BASF or equivalent make) The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, smooth finishing, application, wastage, equipment, tools and plants, fuel, consumables, curing as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Providing 100 mm high skirting with best quality approved granite slab of thickness not less than 18 mm, machine cut and leather finish set in cement mortar at all levels and all as per drawing Rate shall include for preparation of surface, with tin-oxide/ high gloss factory polish. Rate also to include filleting/ chamfering of the edges along with partial recessing of the skirting into masonry / gypsum wall.

Supply and Laying flooring with best quality approved colour 18mm thick Flamed Steel Grey Granite Slab for Staircase and Ramp flooring of size not less than 1200 x 600 mm machine cut and set in C.M 1:4 (1 of cement: 4 of manufactured sand) 20 mm thick topped with white cement slurry (for surface contact of the bottom of the granite slab) as per approved pattern, including finishing the joints with matching shade, cement slurry, cutting, edge chamfering and polishing rough, medium, nice and tin-oxide polish.Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading. preparation of surface, ncessary haccking in RCC surface, cutting to required shape, edging, antiskid grooves,tools and plants, fuel, curing, cleaning, acid wash over finished surface, protection with Gypsum/Pop layer over plastic sheet and removing the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supply & Laying flooring with best quality approved colour Granite Slab, (Black ribbed / Black granite ) not less than 18 mm thick of size not less than 1200 X 600mm machine cut and set in CM 1:4 20 mm thick topped white cement slurry (for surface contact of the bottom of the slab as per approved pattern including the finish joints with matching shade cement slurry cutting edge chamfering and polishing rough medium nice and tin oxide polish. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts working at all levels, transportation charges, loading & unloading charges, preparation of surfaces necessary hacking in RCC surfaces cutting to required shape, edges, tools and plants curing, cleaning, acid wash over finished surface protection with Gypsum / pop layer over plastic sheet and removing the same before handling over as complete with all respect complying with relevant standard specification and as directed by the Engineer in charge

Supplying and fixing Dadooing the wall with ceramic tiles of approved quality, colour and design joint free of size 600x300x10mm thick of approved make, in all floors over a base layer of cement mortar 1:2 (one cement: Two sand) 10mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40 kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supplying and laying of Ceramic tiles of size 305 x 305 x 6mm for flooring approved make and quality with plain/colour with base mortor in CM 1:3, 10mm thick and pointing with white cement by adding suitable colour pigments including finishing, jointing and polishing with neat finish etc., complete. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supplying and fiting the sunken slab area by BRICK-BATCOBA by adding CICO NO 1 or approved equivalent admixture including applying two coats not less than 2 mm thick of TAPECRETE Acrylic Polymer Based Waterproof Coating, over the final coat of cement plaster 12 mm thick with cement sand mortar 13 mixed with water proofing compound like CICO No.1 at the rate specified in the manufacturer's specification after entire completion of laying pipes, sanitary fittings etc.Rate including all materials, labour charges, wastages with necessary lead and lifts, working at all levels, protecting the laid pipes and sanitary fittings, finishing the surface smooth to receive the top coat of water proofing application etc as complete with all respects complying with relevant standard specification and as directed by the Client/Engineer-in-charge

Including applying two coats not less than 2 mm thick of TAPECRETE- Acrylic Polymer Based Waterproof Coating, over the plastered surface as including final coat of cement plaster 12 mm thick with cement sand mortar 13 mixed with approved water proofing compound like CICO No.1 or approved equivalent

Providing and laying hgh quality range of flooring Ecoflex square tile 22 mm thick metallic blue for floor that is extensively used in GYM in plethra of sizes, designs and patterns as per the requirement . The rate including cost of all materials, labour charges, wastages, transportation charges, loading, unloading, with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

STRUCTURAL GLAZING

Structural Glazing: Providing and fixing structural glazing fabricated from roll formed sections made of galvanized steel colour coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS 277 with Zinc of 120 grams / sqm.) with total coated thickness of 0.72mm. The glass holding section made of 304 grade SS of 0.6mm thick. Galvanized steel sections are to be used as stiffeners inside the colour coated steel / powder coated sections as per the design requirement. Design calculations are made to suit wind pressures as given in IS 875.Paint specifications: Primer coat with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick.

Dimensions: The section should be of 37 x 53mm for frame vertical, 37 x 53mm for frame horizontal section and section for reinforcement should be of 31 x 55mm. glass holding section should be of 37 x 37mm for top and bottom grids in between should be of 37 x 18mm. Accessories: Brackets made of CRCA powder coated / electro plated should be used to fix vertical at top and bottom and vertical to slab as per site requirement. Polyurethane brackets should be used to connect horizontal section to vertical sections. Silicone: Natural cure, with good UV resistance to be used. The above frame should be fixed to brick / concrete masonry by using nylon self–expanding cap and driving MS electro plated 80mm long screws into the caps through frames. Glass: 5mm reflective Saint Gobain OR equivalent.

Supplying and fixing Aluminium powder coated Louver in elevation of approved colour shade , outer frame and horizontal louvers made out of 50mm x 25mm Aluminum box section as per drawing.The rate including cost of all materials, labour charges, wastages, transportation charges, loading, unloading, with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

MISCELLANEOUS

Providing Pre construction Anti termite treatment for the building including all chemicals as per standard specifications. Labour charges for preparing the areas for treatment spraying chemicals and other incidential charges etc., complete. The rate shall be inclusive of giving anti-termite treatment to the building for the following four stages including breaking the termite mounds making holes with crow bars at an intervel of 12"to a depth of 8" in the periphery of building and pouring chemicals etc., complete as per ISI 6313-1981 and. The antitermite chemicals used should have 0.5% concentration with 3L solution for the entire operation etc. as directed by the Engineer incharge and including cost of chemicals labour transportion etc.,

Stage:1 Spraying Anti-termite treatement chemicals solution for the foundation before laying the foundation concrete bottom and sides of the foundation.

Stage:2 Spraying anti-termite chemicals solution to the grade beams level spraying has to be done for the grade beams brick masonry in the superstructure in contact with back fill earth.

Stage:3 Spraying anti-termite chemicals solution on sand for the flooring before laying the flooring concrete. The treatment has to be carried out on the sand filling the basement after leveling operation is over.

Stage:4 Spraying anti-termite chemicals solution around the building outside of the building by making crow bar holes at an intervel of 12" to a depth of 8" around the building before laying the plinth projection. This holes has to be be closed after the treatment.

Providing and fixing wall/ Floor to wallheavy duty expansion joint model no. -XH4FS in accordance with the contract drawing and specifications below. The system is proprietary design consisting of heavy dutyaluminum profiles. The expansion joint includes aluminum frames and centre plate which slides between the frame to accommodate movement for floor to floor condition. The system operates mechanically with snap lock into the frame and able to remain flush at all times during normal movement cycle, particularly at full closure. The system should be fixed with appropriate heavy dutyanchors, fasteners and the exposed surface shall be mill finish as standard. It should be designed for thermal movement and withstand heavy vehicular load. Aluminum to conform as per ASTM B221 for extrusion alloy 6063-T5/T6, and contain moisture barrier for maintaining water tightness. Joint Size: 20 MM.

Supplying and fixing Poly-propelene rungs of 25 mm square bar of size 260 x 170 mm for access way including anchorage in walls to a minimum depth of 100 mm with CC 1:2:4 (one cement,two fine aggregate and four coarse aggregate) etc. complete and as directed by the Engineer-in- charge.( Duct Shafts & UG sump, Over Head Tank and wherever n necessary) Note: Rungs to be fixed before concreting and necessary provision to be made in the shuttering.etc complete, as directed by the Engineer-in-charge.

Supplying and fixing Heavy Duty Precast SFRC manhole cover with frame square shape 600mm internal diameters as per approved make etc., The rate including cost of manhole cover with frame, fixing Man-hole over, grouting the anchors with CC 1:2:4 (one cement,two fine aggregate and four coarse aggregate), as complete in all respects complying with relevant standard specifications and as directed by the Engineer-in-charge.

Supply and fixing of Reinforced cement concrete (M40 grade )Rectangular precast seater box a size 1000mm X 450mm X 450mm with 30 mm thick wall including the transportation form the Manufacture factory to site and placing the seater as directed by Engineer incharge

WATERPROOFING

TERRACE WATER PROOF

Supply and laying water proofing treatment for terrace covering the following order and consisting of following operations Making V grooves at the construction joints of size 20 x 20 mm and fing the Groove with CICO No. 3 Quick Setting Waterproofing Compound admixed with cement. The roof slab / gutter slab shall be thoroughly cleaned to remove debris and dust, and applying 2 coats not less than 2 mm of polymer based Elastomeric Coating like TAPECRETE RTU compound and cured for 7 days and followed by a layer of 20 mm thick cement mortar 13 admixed with CICO NO.1 (or) other approved equivalent make shat be spread over the prepared surface

On the spread mortar provide and lay well burnt brick bats (COBA) to a average minimum thickness of 55 mm (e minimum 40 mm thickness at lower end and 70 mm thickness at higher end). An additional layer of brick bat (COBA) shall be laid over the existing brick bat COBA surface if required to get the required gradient for adequate drainage giving a slope of approximately 1 in 120, which will be measured separately under relevant tem

The gap between brick bat shall be filled with cement mortar 1:4 admixed with waterproofing compound like CICO NO 1 or approved equivalent afterwards curing shall be carried out for two days a final layer of cement mortar of 1:3 admixed with water proofing compound Ike CICO NO:1 or approved equivalent make shall be laid to a thickness of 20 mm and draw a false line of 300 mm x 300 mm.The parapet side wall / gutter wall shall be thoroughly cleaned to remove all dust particles and a layer of 15 mm thick CM 1.3 shall be laid to a height of about 300 mm above the top of the terrace Gutter stab on the Parapet Gutter side wall admixed with water proofing compound like the CICO NO:1 or approved equivalent make. Providing, supplying, mixing, applying two coats of ready to use two component Acrylic polymer modified cement based, flexible, water proofing slurry Eke or approved equivalent to a thickness of 2 mm over the plastered surface of operation as per manufacturer's specification and as directed (Plan area of Terrace only will be measured for payment)

Waterproofing of underground water tank with cementitious render coating system TECNOSEAL V1 of THERMAX make :

Surface Preparation : The substrate shall be free from protruding sharp particles, even & sufficient strenght & grade to take load of upcoming structural concrete.

Providing and applying cementitious render coating system TECNOSEAL V1 of M/s. Thermax Ltd., in two coat at a consumption of 4 kg/sqm to wall/slabs as required as per manufacturer’s specification. The rate shall include cleaning to remove dust , oil etc. and treating joints /cracks etc. All junctions between slab and walls and around pipe openings will be protected with polymer modified thixotropic fibre re-inforced cementitious repair mortar BS 5F of M/s. Thermax Ltd. as approved by the departmental engineer and as per manufacturer’s specifications. V-groove to be made at the construction joints and surface cracks and to be filled with polymer modified thixotropic fibre re-inforced cementitious repair mortar BS 5F of M/s. Thermax Ltd. The rate including cost of all materials, surface preparation, application of waterproofing coating, labour charges for all layers and transportation charges and loading & unloading charges etc., complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Swellable bar:

Surface Preparation Before the installation of MAXSHIELD® SWELLBAR, it must be ensured that the surface is dry, clean and free of undulations, oil, dust or laitance. The surface must be completely dry during the time of installation so as to ensure proper bonding.

Providing and applying MAXSHIELD® SWELLBAR must be positioned and fixed either into a suitable groove cast in concrete or directly onto the concrete using adhesives or mechanically. Color - Black, Solid Content - 100%, Specific Gravity (ISO 1183) -1.43 Tensile Strength (ISO 37) - 2 MPa, Elongation at Break (ISO 37) - 400%, Shore A Hardness (ISO 48) - 63 ,Unrestrained Volumetric Expansion Up to 500% .Application Temperature -5⁰ C to 50⁰. The rate including cost of all materials, surface preparation, labour charges for all layers and transportation charges and loading & unloading charges etc., complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Clearing scrub Jungle and Surface dressing of the ground. The rate including hire charges of all machineries, Removing of all rubbish, lead upto 50m , Transportation, and labour charges etc., complete complying with standard specification.

Supplying And Fixing of Rubber Moulded Grey Premium Concrete Kerb of Size 450X125X300mm Using M30 Concrete. The Concrete Shall Be Moulded By Table Mount Vibrated With Polypropylene Fibers At 5% And Curing Compound. The Rate Shall Include Cost of Materials, Transportation, Loading & Unloading Charges And including Necessary Earth Work Pointing With cm. 1:3 To Full Depth Curing Thread Lining etc., completed as standard specification and as directed by the engineer-in-charge.

Supply and Installation of Nylon net fencing as per drawing providing concrete pedastral of size 300mm x 300mm x 1000mm depth and Vertical support of SHS- 60 x 60 x 2mm, horizontal support SHS- 40 x 40 x 2mm at every 3 meter c/c vertical pipe support of height 3.30m (3.0m above ground level 0.60m below ground level). In between the two post 200mm thick solid block work of 200mm height will be provide. The rate including cost of all materials, Earth work excavation, Cost of all Civil works below fencing , welding, supporting, scaffolding and required painting, labour charges and Transportation charges etc., to complete with standard specification as directed by the departmental Engineer-in-charge.

Supply and Installation of WPC Picket fencing of Size - 900 x 75 x17mm as per drawing providing concrete pedastral of size 300mm x 300mm x 450mm depth with Vertical support of MS Pipe-50 x50 x 1.60mm and horizontal support MS Pipe - 50 x25 x 1.60 mm at every 2.40m c/c vertical pipe support of height 1.35m (0.90m above ground level 0.45m below ground level). In between the two post 200mm thick solid block work of 200mm height will be provide. The rate including cost of all materials, Earth work excavation, Cost of all Civil works below fencing , welding, supporting, scaffolding and required painting, labour charges and Transportation charges etc., to complete with standard specification as directed by the departmental Engineer-in-charge.

Supply and Installation of chain link fencing as per drawing at every 2.4 meter c/c vertical pipe support of height 0.9m above existing Compound wall . The rate including cost of all materials, for fencing , welding, supporting, scaffolding and required painting, labour charges and Transportation charges etc., to complete with standard specification as directed by the departmental Engineer-in-charge.

Supplying and laying Tamin Paver Block with pattern 80mm thick, Grey , Black and Red colour of approved sample as per designed Pattern / drawing made of M40 concrete - 80 mm thick including transportation of the blocks to the site preparation of surface including supplying and filling with manufactured sand to 50 mm thick, levelling and compacting with plate vibrator and laying of the inter locking paving blocks with sand binding and final compaction with plate vibrator of 3 tonne capacity finishing the surface including cutting of blocks at the edges including all labour, materials, transportation, shifting etc., complete, as directed by the Engineer-in-charge.

Providing and laying Pebbles for Accupuncture Walkway to the pattern given with neatly finished.

Providing and fixing Cricket Practise Net with necessary supports neat and complete.

Supplying and Fixing Childrens Multi play Equipments in Ankidyne / Equivalent Brand at 5feet-7feet height with product area 19 ft X 17 ft for 10 to 15 kids of 5 -12 years old played at a time and fixing in position. The rate includes the cost of material, transport, surface cleaning slope maintaining and labour charges etc., complete as per drawings and directed by departmental engineers.

SW049 4Seater Arch swing

MGR076 Merry go round 6seater arch 76000

CL107 Rope & Rock Climber

CL119 Square dome climber

CL102 Wall climber

MPS083 Multiplay station Jr

MGR062 Horse MGR 4seater

SL004 Straight slide 10" ft

SS040 Seesaw 4seater

SS036 Horse Seesaw 2seater

SS041 Poppy rider

SS042 Tiger rider

Fixing and Transpor charges for out door Kids play Equipment

Supplying and Fixing of Following Signage's of approved make and fixing in position. The rate includes the cost of all material, Designing charges, Scaffolding, staging, Labour charges, Loading & Unloading charges and Transportation charges etc., complete as per drawings and directed by departmental engineers.

ISIGN POST SIGN Dimension : 400mm x 212mm X 1700mm Post Height Extruded anodized aluminium frame with acp face panel with graphics fixing on MS powder coated 40 x 40 post, single sided, fixing using ancor bold

STRATO WALL MOUNT Dimension : 109 mm X 300 mm Extruded anodized aluminium panel , ABS endcaps, with clear pc sheet, with graphics single sided, fixing using 3M VHB double side tape.

STRATO FLAG MOUNT Dimension : 109 mm X 300 mm Extruded anodized aluminium panel , ABS endcaps, with clear pc sheet, wall bracket,with graphics double sided,

ISIGN SUSPENDED SIGNS Dimension : 300 mm X 450 mm Extruded anodized aluminium frame with acp face panel with graphics double sided, suspended kit,

Supplying and Fixing Indoor Gym Equipments in approved make and fixing in position. The rate includes the cost of material, transport and labour charges etc., complete as per drawings and directed by departmental engineers.

Cofit S201 Spin Bike

Co-Fit MX207 Leg Extension Leg Curl

INSPIRE FT1 Functional Trainer (Requires 6xw5s). Frame:- Heavy Duty Steel ,Electrostatic Powder Coat Product Weight:- 725 lbs (329 kgs) Weight Stack: 2 x 165 lbs (75 kgs) (1:2 ratio for 82.5 lbs per pulley, 85 lbs with 5 lbs Add- On Weights) Opt Add-on:- 2 x 165 lbs (75 kgs) Accessiories:Tablet Holder Attachment, Tricep Rope, 2 x Rubber D Handles, Straight Bar, EZ Curl Bar, Ankle Strap, Multi-Function Belt, Sport Handle, 2 x 5lb Add-On Weights, Exercise Booklet Dimensions (LXWXH):-54 x 46x 82. The rate includes the cost of material, transportation charges and labour charges etc., complete as per drawings and directed by departmental engineers.

Cofit CF-FWI-FID FLAT INCLINE DECLINE BENCH

CF-7043-S Co-Fit Olympic Weight Bench

Cofit Barbell rack

Co- fit 805 commercial treadmi specification sped range 08-25 km/h incline rang 18 level motor max 6.5 HP AC Motor running belt 160 x 58 cm type of monitor 7 inch bue backlight LCD . Variable 36 training programs large commercial safety handrails dimension ( Lx W x H) 212 X 94 X 153 CM. The rate includes the cost of all material, transportation charges and labour charges etc., complete as per drawings and directed by departmental engineers.

DBRH 3-TIER DUMBBELL RACK Dimension : WLH : 19 in x 53 in x 34 inches Weight : 89 lbs

JL RUBBERISED ,HEXAGONAL DUMBBELLS, 2.5KG (PAIR)

JL RUBBERISED HEXAGONAL DUMBBELLS 5KG (PAIR)

JL RUBBERISED HEXAGONAL DUMBBELLS 7.5KG (PAIR)

JL RUBBERISED HEXAGONAL DUMBBELLS 10 KG (PAIR)

JL RUBBERISED HEXAGONAL DUMBBELLS 12.5 KG

JL RUBBERISED HEXAGONAL DUMBBELLS 15KG

JL RUBBERISED HEXAGONAL DUMBBELLS 17.5KG

JL RUBBERISED HEXAGONAL DUMBBELLS 20KG

JL OLYMPIC RUBBER COATED PLATES 2.5KG (PAIR)

JL OLYMPIC RUBBER COATED PLATES 5KG (PAIR)

JL OLYMPIC RUBBER COATED PLATES 7.5KG (PAIR)

JL OLYMPIC RUBBER COATED PLATES 10KG (PAIR)

JL OLYMPIC RUBBER COATED PLATES 15KG

JL OLYMPIC RUBBER COATED PLATES 20KG

JL OLYMPIC RUBBER COATED PLATES 25KG

Olympic Straight Bar 4inch

OB-47 OLYMPIC E-Z CURL BAR 4 FEET

OB-60 OLYMPIC STRAIGHT BAR 5 feet

OB-72 OLYMPIC STRAIGHT BAR 6 feet

OLYMPIC BARBELL 7 FT OB86

Supplying and Fixing Outdoor Gym Equipments in approved make and fixing in position. The rate includes the cost of material, transport and labour charges etc., complete as per drawings and directed by departmental engineers.

Sky Walker - Single person This product is fabricated using IS 1239(Part 1) GI standard ISI grade pipes. Heavy duty bearings are used.The equipment will be painted with good quality PU paint with UV protection and smooth finish. The product color approved by Executive engineer before commencement of work. The rate including cost of material, transport and labour charges etc., complete as per drawings and directed by departmental engineers.

Double Bar/Parallel Bar This product is fabricated using IS 1239(Part 1) GI standard ISI grade pipes. The equipment will be painted with good quality PU paint with UV protection and smooth finish. The product color may vary and the color in the image is for representational purpose only. The rate includes the cost of material, transport and labour charges etc., complete as per drawings and directed by departmental engineers.

Single Bar This product is fabricated using IS 1239(Part 1) GI standard ISI grade pipes. The equipment will be painted with good quality PU paint with UV protection and smooth finish. The product color may vary and the color in the image is for representational purpose only.. The rate includes the cost of material, transport and labour charges etc., complete as per drawings and directed by departmental engineers.

Exercise Bike This product is fabricated using IS 1239(Part 1) GI standard ISI grade pipes. Heavy duty bearings are used. The equipment will be painted with good quality PU paint with UV protection and smooth finish. The product color may vary and the color in the image is for representational purpose only. The rate includes the cost of material, transport and labour charges etc., complete as per drawings and directed by departmental engineers.

Push Up Bar This product is fabricated using IS 1239(Part 1) GI standard ISI grade pipes. The equipment will be painted with good quality PU paint with UV protection and smooth finish. The product color may vary and the color in the image is for representational purpose only. The rate includes the cost of material, transport and labour charges etc., complete as per drawings and directed by departmental engineers.

GM133 Cycle

GM140 Standing triple twister

GM137 Thai chi spinner 4 wheel 1

Fixing and Transpor charges for out door GYM Equipment

Sunvel Tensile Roofing: Design, Supply, fabrication and erection of mild steel Channel Section & Rectangular Hollow Sections and painted with one coat epoxy primer and two coat paint. The membrane fabric shall be Ferrari/Verseidag Fabric Type - II. The mild steel structure has to be surveyed and the fabric pattern has to be generated and the same will be plotted and welded. The cables and corner plates are GI, pockets will be filled with PVC cedars and fixed on to the steel structure by using fasteners. The rate including cost of MS sections, roofing sheet materials, labour charges, Loading & Unloading, Transportation charges etc., complete with relevant standard specification and as directed by the Departmental Engineer-in-charge.

Supplying of Play Ground Maintaining Equipment of approved make approved by Executive Engineer. The rate including the cost of material, transport, Loading and Unloading charges and labour charges etc., complete as per directed by departmental engineers.

Providing Roller - 2 Ton

Manual Roller

Mower - Grass cutting

Providing Automatic Sprinklers for Grass in Ground

Providing and Fixing Turnstile Gate at the entrance of park for 6' wide and 5' height The rate including cost of all materials, Earth work excavation, Cost of all Civil works below, welding and required painting, labour charges and Transportation charges etc., to complete with standard specification as directed by the departmental Engineer-in-charge.

Providing Landscape work

Supply & stacking of red earth at site to the departmental guage for pre-measurements which is of light textured, crystalline, porous and friable and not of generally acidic or neutral but not of alkaline and should be fertile, including seignior age charges, cost of transportation, loading, unloading, stacking and inclusive of all taxes etc., complete. PD-1294

Supplying and stacking of sand (supply & stacking of sand at site to the depatmental guage for premeasurements obtained from natural disintegrated rock which has been deposited by streams or glacial agenciesed of hard silicons materails and should be clean, sharp and angular type free of adherent coatings). The rate including cost of river sand, transportation, loading & unloading, stacking etc., complete and as directed by Engineer-in-charge.

Supply of well decomposed Farm yard Manure in a powdery form, devoid of soil sand, stones, plastics and other materials, highly nutrient and which supports plant growth. PD-1295

Mixing charges of Red soil, sand and manure uniformly (1:1:1) for Preparation of soil mixture (excluding material cost) PD-1296

Spreading of red soil, gravel or sand including watering and rolling which hand roller for every 75 mm thickness - including hire charges of roller. PD-1297

Planting of Acalypha varieties ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth, watering, transportation charges etc., complete and as directed by Engineer in charge. PD-1307

Planting of Caesalpinia pulcherrima foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges,transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth, watering, transportation charges etc., complete and as directed by Engineer in charge.. PD-1319

Planting of Ficus black ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth , watering, transportation charges etc., complete and as directed by Engineer in charge. PD-1335

Planting of Eranthemum varites ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges,Transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth , watering, transportation charges etc., complete and as directed by Engineer in charge. PD-1332

Planting of Ficus ponda ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth , watering, transportation charges etc., complete and as directed by Engineer in charge. PD-1336

Planting of Hemelia pattens foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth , watering, transportation charges etc., complete and as directed by Engineer in charge. PD-1341

Planting of Ixora dwarf varieties foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth , watering, transportation charges etc., complete and as directed by Engineer in charge.PD-1345

Planting of Nerium oleander foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth , watering, transportation charges etc., complete and as directed by Engineer in charge. PD-1358

Planting of Pisonia ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth , watering, transportation charges etc, complete and as directed by Engineer in charge . PD-1365

Planting of Tabernum dwarf foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth , watering, transportation charges etc., complete and as directed by Engineer in charge etc. PD-1374

Planting of Tecoma goudi choudi foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth , watering, transportation charges etc., complete and as directed by Engineer in charge. PD-1377

Planting of Mussanda ornamental foliage Specimen plant variety of height 105-120 cm in polythene bag of size 16x16 inch including loading and unloading charges,transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth, watering, transportation charges etc., complete and as directed by Engineer in charge. PD-1416

Supplying and Planting of Peltophorum tree sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth watering, transportation charges etc., complete and as directed by Engineer in charge. PD-1491

Planting of African grass ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth, watering, transportation charges etc., complete and as directed by Engineer in charge. PD-1308

Planting of Allamanda dwarf foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth,watering, transportation charges etc., complete and as directed by Engineer in charge. PD-1310

Planting of Aralia ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge. PD-1312

Planting of Bougainvillea hybrid foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge . PD-1316

Planting of Caladium kinds ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in chargeetc as directed by the site in-charge. PD-1320

Planting of Canna indica varigated Plant foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge etc. PD-1321

Planting of Clerodendron green / variegated Plant ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge etc. . PD-1322

Planting of Dracena marginata ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth,watering, transportation charges etc., complete and as directed by Engineer in charge etc. PD-1330

Planting of Dracena babydoll ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge etc. PD-1327

Planting of Duranta new gold Plant ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge etc. . PD-1331

Planting of Euphorbia milli foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge etc. PD-1333

Planting of Galphimia Plant foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge etc. PD-1338

Planting of Graptophyllum pictum varieties ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge etc. PD-1339

Planting of Heliconium foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge etc.. PD-1340

Planting of Hibiscus hawai foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth,watering, transportation charges etc., complete and as directed by Engineer in charge etc . PD-1342

Planting of Hibiscus hybrid foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth,watering, transportation charges etc., complete and as directed by Engineer in charge etc. PD-1343

SupplyiPlanting of Lavender Plant ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge etc PD-1350

Planting of Leo cocksenia ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, p,watering, transportation charges etc., complete and as directed by Engineer in charge etc PD-1351

Planting of Nerium oleander foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge etc. PD-1358

Supplying and Planting of Plumbago foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge etc. PD-1366

Planting of Schefflera variated ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge etc PD-1371 .

Planting of Song of India Plant ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth,watering, transportation charges etc., complete and as directed by Engineer in charge etc PD-1372

Planting of Tabernum green foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth,watering, transportation charges etc., complete and as directed by Engineer in charge etc. PD-1375

Planting of Tecoma goudi choudi foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge etc. PD-1377

Supplying and Planting of Bauhinia purpurea tree sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge etc . PD-1472

Supplying and Planting of Cassia fistula tree sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth,watering, transportation charges etc., complete and as directed by Engineer in charge etc. PD-1474

Supplying and Planting of Cordia sebestena tree sapling of height 240 – 300 cm in polythene bag of size 20x21 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge etc PD-1515

Planting of Asparagus springeri ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge etc . PD-1314

Planting of Lilly foliage shrub variety of height 30- 45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge etc . PD-1352

Planting of Pandanus ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge etc. PD-1360

Planting of Tabernum dwarf foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, transportation charges etc., complete and as directed by Engineer in charge etc. 2 PD-1374

Planting of Lantana foliage Ground cover variety in polythene bag of dia 20 cm including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, trans portation charges etc., complete and as directed by Engineer in charge etc. PD-1397

Planting of Ophiopogon ornamental foliage Ground cover variety in polythene bag of dia 20 cm including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, trans portation charges etc., complete and as directed by Engineer in charge etc PD-1398

Planting of Syngonium foliage Ground cover variety in polythene bag of dia 20 cm including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, trans portation charges etc., complete and as directed by Engineer in charge etc 8 PD-1400

Planting of Wedelia trilobata foliage Ground cover variety in polythene bag of dia 20 cm including loading and unloading charges, transportation, stacking of sapling at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, trans portation charges etc., complete and as directed by Engineer in charge etc. PD-1403

Planting of Cyprus Plant ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, trans portation charges etc., complete and as directed by Engineer in charge etc. PD-1325

Planting of Adenium Specimen plant variety of height 105-120 cm in polythene bag of size 16x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth,watering, trans portation charges etc., complete and as directed by Engineer in charge etc. PD-1404

Planting of Bottle brush gold foliage Specimen plant variety of height 105-120 cm in polythene bag of size 16x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth,watering, trans portation charges etc., complete and as directed by Engineer in charge etc. PD-1405

Planting of Cycus revoluta 21- 30 Leaves ornamental foliage Specimen plant variety of height 105-120 cm in polythene bag of size 16x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth,watering, trans portation charges etc., complete and as directed by Engineer in charge etc. PD-1408

Planting of Ficus starlight ornamental foliage Specimen plant variety of height 105-120 cm in polythene bag of size 16x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth,watering, trans portation charges etc., complete and as directed by Engineer in charge etc. PD-1411

Planting of Ficus benjamina green ornamental foliage Specimen plant variety of height 105-120 cm in polythene bag of size 16x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth,watering, trans portation charges etc., complete and as directed by Engineer in charge etc. PD-1412

Planting of Furcarea ornamental foliage Specimen plant variety of height 105-120 cm in polythene bag of size 16x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth,watering, trans portation charges etc., complete and as directed by Engineer in charge etc. PD-1414

Supplying and Planting Juniperous Specimen plant with necessary earth Planting of Juniperous ornamental foliage Specimen plant variety of height 105-120 cm in polythene bag of size 16x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, trans portation charges etc., complete and as directed by Engineer in charge etc. PD-1415

Planting of Terminalia Metalica ornamental foliage Specimen plant variety of height 105- 120 cm in polythene bag of size 16x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, trans portation charges etc., complete and as directed by Engineer in charge etc. PD-1420

Planting of Thuja ornamental foliage Specimen plant variety of height 105-120 cm in polythene bag of size 16x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, trans portation charges etc., complete and as directed by Engineer in charge etc. PD-1422

Planting of Eugenia uniflora Specimen plant variety of height 105-120 cm in polythene bag of size 16x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, trans portation charges etc., complete and as directed by Engineer in charge etc. PD-1410

Supplying and Planting of Dypsis lutescens (Areca palm) palm variety of height 180-210 cm in polythene bag of size 16x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, trans portation charges etc., complete and as directed by Engineer in charge etc. PD-1427

Supplying and Planting of Raphis palm variety of height 180-210 cm in polythene bag of size 16x16 inch including supporting stack of 5cm dia casurina pole of 10' height,including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, trans portation charges etc., complete and as directed by Engineer in charge etc .PD-1431

Supplying and Planting of Roystonea regia (Royal palms) palm variety of height 180-210 cm in polythene bag of size 16x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, trans portation charges etc., complete and as directed by Engineer in charge etc .PD-1432

Supplying and Planting of Wodyetia bifurcata (Foxtail palms) palm variety of height 180-210 cm in polythene bag of size 16x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, trans portation charges etc., complete and as directed by Engineer in charge etc . PD-1436

Supplying and Planting of Budha Belly Bamboo tree sapling of height 300 - 360 cm in polythene bag of size 15x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, trans portation charges etc., complete and as directed by Engineer in charge etc . PD-1546

Supplying and Planting of Golden Bamboo tree sapling of height 300 - 360 cm in polythene bag of size 15x16 inch including loading and unloading 266 PD-1548 charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, trans portation charges etc., complete and as directed by Engineer in charge etc . PD-1548

Truffing of Korean grass / mexican grass including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, trans portation charges etc., complete and as directed by Engineer in charge etc PD-1466

Planting of Shade grass including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth ,watering, trans portation charges etc., complete and as directed by Engineer in charge etc PD-1467

MANUAL IRRIGATION SYSTEM

UPVC pipe 80mm SCH - 80 - Mainline

UPVC Pipe 65mm SCH - 80

UPVC Pipe 50mm SCH - 80

UPVC Pipe 25mm SCH - 80

UPVC Pipe 20mm SCH - 80

Drip & Accessories

Supply, fixing & commissioning of with resistance flexible 16mm inline tubing PC Drippers with resistance to UV damage, algaal growth brown in color, Longer Lateral run length with flow rate 2.3lph / 4.0lph pressure rating 0.58 to 4.1bar. Dripper spacing 30cm / 45cm spacing wall thickness 1.2mm etc. (Make :TECHNET /XERITECH / PLD) The rate including Cost of all amterials , labour charges and transportation charges etc., Complete with relevent standar specification as dircted by the departmental Engineer-in-charge.

Supply,fixing and commissioning of 2" Large Y Type Disc / Screen Filters for submain filtration have High Flow & Low maintenance with a solid buikld , maximum flow upto 110 gpm, maximum pressure 16psi, maximum temperature upto 114 ͦ F etc. complete (Make : RAINBIRD /XERITECH / ARMAS) The rate including Cost of all amterials , labour charges and transportation charges etc., Complete with relevent standar specification as dircted by the departmental Engineer-in-charge.

Sprinklers & Accessories

Supply, fixing and commissioning of 5004 PLUS SAM PRS Series Rotor Pop Up Sprinkler full / part circle having radius of 6.7m - 12m @ 2.5 - 4.5 bar with discharge of 0.09 - 0.61 ltr / sec Sprinklers having Arc adjust, through top cover w/Std screwdriver. Sprinkler is gear driven rotary type with having 3/4" bottom inlet. Sprinkler shall have PL flow shutoff, 45psi pressure regulator with flow optimizer techno;ogy, internal seal, A-matic device which prevents low head drainage and hence puddling and erosion. (Make : RAINBIRD / 5004 PLUS PRS ) The rate including Cost of all amterials , labour charges and transportation charges etc., Complete with relevent standar specification as dircted by the departmental Engineer-in-charge.

Supply fixing & commissioning of 1804 Series Pop Up Sprinkler full/part circle having radius 3.1m - 5.9m @ 2.5 - 4.5 bar with discharge of 0.04 - 0.21 ltr/sec. Sprinkler shall have PL flow shutoff, 45 psi pressure regulator with flow optimizer technology internal seal make of RAINBIRD. The rate including Cost of all amterials , labour charges and transportation charges etc., Complete with relevent standar specification as dircted by the departmental Engineer-in-charge.

Valves & Accessories

Supply, fixing and commissioning of PVC Single Union Ball Valve which permitsmaximum penetration of valve size of 63mm with pressure rating PN 10 etc (Make:PIMTAS / XERITECH) The rate including Cost of all amterials , labour charges and transportation charges etc., Complete with relevent standar specification as dircted by the departmental Engineer-in-charge.

Supply, fixing & commisssioning of a double acting air and vaccuum release 1/2" Air Release Valve. (Make: RAINBIRD / XERITECH ) The rate including Cost of all amterials , labour charges and transportation charges etc., Complete with relevent standar specification as dircted by the departmental Engineer-in-charge.

Supply, fixing & commisssioning of a double acting air and vaccuum release 2" Air Release Valve. RAINBIRD / XERITECH

Supply,fixing & commissioning of 6" Round Box with greenlid with features of overlapping lid, skid resistant lid texture etc. complete ( Make: RAINBIRD/XERITECH/PIMTAS ) The rate including Cost of all amterials , labour charges and transportation charges etc., Complete with relevent standar specification as dircted by the departmental Engineer-in-charge.

Supply,fixing & commissioning of 10" Round Box with greenlid with features of overlapping lid, skid resistant lid texture etc. complete RAINBIRD/XERITECH/PIMTAS

Supply,fixing and commissioning of 12" Rectangular Standard Valve Box etc.complete ( Make : RAINBIRD/XERITECH/PIMTAS ) The rate including Cost of all amterials , labour charges and transportation charges etc., Complete with relevent standar specification as dircted by the departmental Engineer-in-charge.

Supply, fixing & commissioning of 3/4" Quick Coupling Valve made up of solid brass ( Make : RAINBIRD / EQUIVALENT ) The rate including Cost of all amterials , labour charges and transportation charges etc., Complete with relevent standar specification as dircted by the departmental Engineer-in-charge.

Supplying fixing & commissioning of 3/4" Key thread into the top of Quick Coupling Valve to provide water access etc. complete ( Make : RAINBIRD / EQUIVALENT ) The rate including Cost of all amterials , labour charges and transportation charges etc., Complete with relevent standar specification as dircted by the departmental Engineer-in-charge.

Supply, fixing & commissioning of 3/4" Hose Swivel made up pof solid brass Swivels upto 360 ͦ ( Make : RAINBIRD / EQUIVALENT ) The rate including Cost of all amterials , labour charges and transportation charges etc., Complete with relevent standar specification as dircted by the departmental Engineer-in-charge.

Filtration Unit

Supply, fixing & commissioning of 3" Disc Filter with capacity 50M3/Hr having a suitable inlet connection to create a helical effect in the incoming water , spinning particulate in suspension away from the filtering element , working pressure of 10 Bars etc., complete ( Make : ARMAS / XERITECH ) The rate including Cost of all amterials , labour charges and transportation charges etc., Complete with relevent standar specification as dircted by the departmental Engineer-in-charge.

Pumping Unit

Supply, fixing & commissioning of Monobloc Pumpset of having discharge and head of design flow with required suction & delivery pipelines and mounted on a base frame with proper support etc. complete Duty of Pump 3.9LPS Pressure of head Range 39 - 42M No. of Pumps 1Working + 0 Standby ( Make : DAG/TEXMO/KIRLOSKAR/EQUIVALENT) The rate including Cost of all amterials , labour charges and transportation charges etc., Complete with relevent standar specification as dircted by the departmental Engineer-in-charge.

Supply,fixing & commissioning of control panel suitable for pumpset having panel box made of CRCA Sheet of 2mm thickness and fixed alongwith accessories DOL / Star Delta Starter MUG 10 L&T make , Ammeter, Single phase preventor Voltmeter Indicating lamps MCB Dry level guard etc complete ( Make: L&T/Equivalent ) The rate including Cost of all amterials , labour charges and transportation charges etc., Complete with relevent standar specification as dircted by the departmental Engineer-in-charge.

Supply ,Fixing & Commissioning of Control Cable for Pump Set - 3 core X 4 / 6 Sq.mm Copper cable based on the pump capacity ( Make : Finolex / Polycab ) The rate including Cost of all amterials , labour charges and transportation charges etc., Complete with relevent standar specification as dircted by the departmental Engineer-in-charge.

Supply,Fixing & commissioning of 3'' control Valve, Butterfly Valve VAN Stone flange & Tail Piece in mainline for bypass and flow diversion of approved quality with pressure rating of PN 10 etc., complete (Make : PIMTAS / XERITECH ) The rate including Cost of all amterials , labour charges and transportation charges etc., Complete with relevent standar specification as dircted by the departmental Engineer-in-charge.

Supply,Fixing & commissioning of 3'' Non Return Valve to prevent back flow have flap type or spring type with pressure rating of PN 10 etc., complete, (Make : PIMTAS / XERITECH) The rate including Cost of all amterials , labour charges and transportation charges etc., Complete with relevent standar specification as dircted by the departmental Engineer-in-charge.

Supply,Fixing & commissioning of Pressure release valve 3" with pressure setting from 0 to 7 Bar etc., complete (Make: ARMAS / XERITECH) The rate including Cost of all amterials , labour charges and transportation charges etc., Complete with relevent standar specification as dircted by the departmental Engineer-in-charge.

Sub Total Manual irrigation System

Charges for Design of Landscaping and Irrigation Watering system, Submission of Shop drawing, As built drawings, Supporting Documents and Training for maintenance team after commissioning of the system. The rate including designing cost, Submission of Drawings and documents , supervision charges for landscaping start to complete etc., complete as directed by departmental Engineer-in-charge.

SANITARY INSTALLATIONS

Supply and fixing in position white European Water Closet of approved make with low level flushing tank 10 litre capacity of best quality and approved make with 100mm P or S trap with double flapped rigid PVC seat cover with CP brass hinges etc. complete complying with standard specification and as directed by the Departmental officers (The EWC should be got approved by the Executive Engineer before use on works.

Supplying and fixing in position Indian water closet of size 580 x 440mm, glazed earthern ware of approved quality and colour with 'P' trap or 'S' trap confirming to IS:2556-part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One of Lime, Two of Sand, Five of Brick jelly) 100mm thick and by dismantling brick masonry, reinforced finishing to the required slope and including giving necessary connection to PVC soil pipes cement concrete roof / floor slab and making good the disturbed portion to origional condition without leakage etc., complete complying with standard specification and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works)

Supplying and fixing Wash Hand Basin white colour without pedestal of size 550 mm X 400 mm with all accessories such as cast Iron Brackets, 32 mm Dia C.P. Waste coupling, Rubber plug and Chain, 32 mm dia ' B ' Class G.I. Waste pipe, 15 mm Dia G.M Wheel valve; 15 mm Dia Nylon connection, 15 mm Dia Brass Nipples, 15 mm C.P. Pillar tap etc.,including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and as directed by the Department officers. The quality and make of below counter Wash basin should be got approved by department Engineer before use on work

Supplying, Installing, Testing and Commisioning the best quality approved make of white glazed floor mounted european water closet with inbuild porcelin cistern 6/3 LPF and wash basin for physically challenge persons (hindware -matrix -70002)with necessary grap railes,hinged railes for support,pan connector bend ,checknut,stopcock etc,. colour solid seat and cover with polythene buffer and flap,CP flanges, CP bolts and nuts,brackets with nuts and boults wall flanges etc, complete ,wash basin shall include 15mm dia CP lever oprareted piller cock with waste coupling , 32mm dia CP bottle trap with extension pipe,supporting bracket with neccesary steel to support the basin 1 No,15mm CP angle valve with 450mm long CP connection pipe and CP wall flanges all of approved make etc., complete complying with standard specification and as directed by the department officers.the quality and make of EWC & wash basin with full set should be got approved by the Executive Engineer before use on work.

Supplying and fixing Lipped Mouth Porcelain Flat Back Urinal(white colour) of size 26.5x31.5x44cm with all accessories such as 32mm dia Bell Mouth PVC Connection, 15mm dia GM Wheel Value, 15mm dia 'B' Class GI Waste Water Pipe, 15mm dia Nylon Connection, 15mm dia Brass Nipple, and suitable screws, shellac etc., complete. The rate including cost of all materials, labour charges for fixing and transportation etc. completed as directed by Engineer-in-Charge.

Supplying and fixing heavy duty 15mm CP shower unit comprising of CP 15mm dia hot & cold mixer with CP spout, overhead shower set comprising of CP shower arm, rose etc.,complete with CP wall flanges. The rate including cost of all materials, labour charges and transportation etc. completed as directed by Engineer-in-Charge.

Supplying & fixing in position 15 mm dia brass/ C.P pillar tap (Heavy duty) of approved make conforming to I.S. Specifications & quality including cost of shellac, thread etc., complying with standard specifications & including cutting & threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the work).

Supplying and fixing of CP Two Way Bib Cock with Health Faucet ,wall hook & one metre long flexible tube including cutting and making good the walls wherever required etc complete. complying with standard specification and as directed by the Department officers. The quality and make of health faucet should be got approved by Concern department Engineer before use on work.

Supplying and fixing C.P. Robe hook fixing with necessary screws etc., complete. fixed on the toilet door complying with standard specification and as directed by the Department officers. The quality and make of coat hook should be got approved by Concern department Engineer before use on work.

Supplying and fixing Brass Chromium Plated Towel Rail 60cm long and 20mm dia with brackets of same materials including cost of teak wood plug & CP screws etc., complying with standard specification and as directed by the Department officers.

Supplying and fixing Brass Chromium Plated Soap Tray of size 150mm x 100mm using rawl plug & brass screws for fixing etc., complete complying with standard specification and as directed by the Engineer Incharge before use on work.

Supplying and fixing CP angle cock with wall flange including cutting and making good the walls wherever required etc., complete complying with standard specification and as directed by the Engineer Incharge before use on work.

Supplying and fixing in position Mirror of size 1000x780mm of approved quality and brand with necessary plastic back PVC frame with bottom stand using brass screws rawl plugs for fixing etc complete complying with standard specification and as directed by the Departmental officers. The colour of frame and quality of mirror should be got approved by the Executive Engineer before use on work

Supplying & fixing in position PVC Nahini / Floor trap of size 100x75mm including stainless steel gratings of approved brand & quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( One part of lime, two parts of sand & five parts of 40 mm size brick jelly ) & finished with cement mortar 1:3 ( One cement & three sand ) including dismantling masonry works wherever found necessary & making good the damaged portions to the original condition & giving connections to the cast iron pipes etc., complete, complying with standard specification. (The PVC Nahini / Floor trap should be got approved by the Executive Engineer before use on works ).

DRAINAGE WORKS

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). Internal & Vertical

50mm dia

75mm dia

110mm dia

110mm dia

160mm dia

Supplying and fixing PVC cowl of following size to vertical Soil/Waste pipes above terrace level. The rate including cost of all materials, labour charges and transportation etc. completed as directed by Engineer-in-Charge.

75mm dia

110mm dia

Supplying & fixing in position 150 X 100 mm square mouth 'P' or 'S' trap stone ware Gully trap 'A' grade with cast iron double gratings of size 150 X 150 mm with C.I. air tight cover with frames of size 300 X 300 mm at bottom & top respectively with necessary earth work excavation, laid over a bed of brick jelly cement concrete 1:3:6, 150 mm thick using 20 mm size broken brick jelly including necessary brick work & plastering, &including dismantling masonry wherever necessary & redoing the damaged portions to the original condition & by using cement concrete 1:3:6 using 20 mm stone jelly for fixing the Gully trap & giving connections to the stone ware sewer line etc., complete, complying with standard specification. (The stone ware gully trap should be got approved by the Executive Engineer before use on works ).

600 x600 mm x450mm to 1000mm deep

900 x 900 mm x 1000mm to 1500mm deep

1200 x 1200 mm x 1500mm to 2000mm deep

Providing and laying non-pressure class NP2 RCC Spun pipes with collars including excavation of trenches in soil/murum/rock, laying the pipes as per layout and drawing, filling the joints with stiff mixture of cement mortar (1 part cement :1part fine sand) and jute, curing, testing the pipe and refilling the trenches in layers with due compaction & watering etc. complete as directed

200mm dia NP2 RCC Hume Pipe

250mm dia NP2 RCC Hume Pipe

Making through holes in Plain or Reinforced Cement Concrete with Diamond Core Drilling System by using BOSCH power tools of following diameter in 150mm thick toilet floor slab

WATER SUPPLY WORKS

Supplying, laying and jointing CPVC pipes SDR 11(having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using CPVC adhesives and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works. Internal & Vertical

15mm dia

20mm dia

25mm dia

32mm dia

40mm dia

50mm dia

65mm dia

20mm dia

25mm dia

50mm dia

65mm dia

80mm dia

Supplying, laying, jointing, testing & commissioning approved make class 'B' G.I. pipes and fittings confirming to IS 1239 PI & II, malleable fittings viz.,including labour for fixing GI Specials (excluding charges for cutting and threading and cost of such specials) with necessary shellac, thread ball, etc., and making holes on the wall / concrete and making good the dismantled portion to the original condition with necessary brick work / concrete. The pipes are to be painted with one coat of tar and tightly pastened with tar dipped gunny tape, etc., complete complying with standard specification. The G.I. pipes shall be got approved by the Executive Engineer before use on work. (The earth work excavation, re-filling the trench with excavated earth, sand filling, etc., shall be measured and paid separately under respective items). Below ground level (Pumproom)

50mm dia

65mm dia

80mm dia

100mm dia

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

20mm dia

25mm dia

32mm dia

40mm dia

50mm dia

65mm dia

Providing and fixing CI D/F Sluice valve with cap / wheel as per IS 14846/2000 PN 1.0 with ISI Marking make of the following dia including cost of bolt & nuts, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work

65mm dia

80mm dia

100mm dia

Providing and fixing GM Non return valve as per IS BS 5154 and related IS Specifications make of the following dia including cost of bolt & nuts, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work

50mm dia

65mm dia

80mm dia

Providing and placing on terrace PVC water tank 2,000lts. capacity, with cover and suitable locking arrangement. The rate includes cost of tank, transportation charges and placing the tank in postion etc. complete and as directed by the Departmental officers.

Providing and placing on terrace PVC water tank 1,000lts. capacity, with cover and suitable locking arrangement. The rate includes cost of tank, transportation charges and placing the tank in postion etc. complete and as directed by the Departmental officers.

PUMPS & RO UNIT

Supply and delivery of Electric Monoset centrifugal pump conforming to IS 9079:2002 as amended from time to time, with CI FG 200 Casing, hydraulically and dynamically balanced Bronze grade LTB-2 impeller, impeller ring and casing ring, stainless steel shaft capable of discharging required quantity of water against a total head noted below due to all causes. Pump shall of BEE 3 Star Rated and capable of discharging the specified quantity at the head noted at the minimum NPSHA at site conditions. The shut off head shall be atleast 25% over and above the head at duty point. The pump shall be suitable for operation in AC three phase , 415 V+/- 10% , 50 Hz +/- 5%. Squirrel cage induction motor for continuous operation. The speed of the Pump and Motor shall be not less than 2700 to 2900 RPM respectively. Domestic / Landscape Water Pump (From Domestic Sump to O.H.T) Duty of Pump : 100 lpm x 20m head

Supply and delivery of Electric Monoset centrifugal pump conforming to IS 9079:2002 as amended from time to time, with CI FG 200 Casing, hydraulically and dynamically balanced Bronze grade LTB-2 impeller, impeller ring and casing ring, stainless steel shaft capable of discharging required quantity of water against a total head noted below due to all causes. Pump shall of BEE 3 Star Rated and capable of discharging the specified quantity at the head noted at the minimum NPSHA at site conditions. The shut off head shall be atleast 25% over and above the head at duty point. The pump shall be suitable for operation in AC three phase , 415 V+/- 10% , 50 Hz +/- 5%. Squirrel cage induction motor for continuous operation. The speed of the Pump and Motor shall be not less than 2700 to 2900 RPM respectively. Domestic/Landscape Water Pump (From Domestic Sump to O.H.T) Duty of Pump : 100 lpm x 35m head

Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No.

(e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact. Capacity : 500 Litres

BOREWELL

Drilling of 12" dia vertical borewell so as to have a finished size of 6" dia borewell in boulder area to any required depth as decided by the TWAD Board Officers including Transportation from one place to anothr place with in Tamilnadu State by direct or reverse rotary mud circulation method using Contractor's rig tools, fuel, labourers, bentonite mud and water required for drilling at the site shown by the TWAD Officers including construction of mud pit etc. using only calyx rigs.

Reaming from 200mm dia pilot bore to 350mm dia bore as direct by the Engineer incharge up to 80mtr depth ending below ground level

Supply and laying following dia PVC casing pipe with excise duty as per IS 12818 / 1992

200mm dia CS ( plain pipe

200mm dia RS

150mm dia RS

Labour charges for inserting PVC casing pipes assembly (with slots or without slots) in the drilled hole including jointing the pipes with PVC couplers with cement paste etc., complete, supply and packing the annular space with pebbles of size and quality as approved by the Executive Engineer of Departmental officers.

200mm dia CS

200mm dia RS

150mm dia RS

Supplying and filling with river pebbles in annular space between bore and PVC pipe up to hard rock.

Charges for developing the borewell with air compressor of 300 CFM capacity (Minimum 8 Hours) including transportation labour and fuel charges for compressor as directed by TWAD Board Officers and conducting yield test by 'V' notch method.

Supply ,erection and testing & commisioning of 3HP submersible pumpset in the to suit 200mm borewell of capacity of 4800 LPH @ 265Ft, max. total head of 280 Ft pumps fitted with bronze impellers and having delivery size of 40mm - 430V along with 3mts cable and manufactures standard control panel which is mandatory and as directed by the officer incharge and other required supporting items like SS hose nipple, nylon rope, clamps, bolt and nuts,GI nipple, 50mm dia HDPE hose of required length etc completed and as directed by the officer incharge.

ELECTRICAL WORKS

Metering Panel - Supply, Installation, Testing and Commissioning of CPRI approved make of panel, cubicle type, Free standing, floor mounted, single front, 14 SWG CRCA sheet steel, enclosed separate compartment for each feeder, front operated, Powder coated, indoor type dust and vermin proof, hinged lockable doors, complete with electrolytic grade copper bus bars, internal wiring, colour coding, ferrules, Panel mounting MS Channels, fasteners, etc., RYB indication lamps, internal wirings, Digital voltmeter and Ammeter and other required accessories for the complete operation as per the Tangedco requirements. Necessary approval to be obtained from Tangedco before procurement including all associated control wiring. 1set of 125/5A CT with TNEB metering provision and 1 nos of 125A /5A CT for APFC.. For all items in this section, the rate includes necessary supports as required at site. No extra payment will be made for the same. Rate shall inclusive of factory witness test and all accessories, breakers , control wiring, models has to be followed as per in the technical specification.

125A Isolator Panel - Supply, Installation, Testing and Commissioning of CPRI approved make of 100A TPN MCCB panel, cubicle type, Free standing, floor mounted, single front, 14 SWG CRCA sheet steel, enclosed separate compartment for each feeder, front operated, Powder coated, indoor type dust and vermin proof, hinged lockable doors.

Supply, Erection, Testing and Commissioning of 62.5KVA Diesel Generator set with AMFcontrol panel, comprising of Water cooled CPCB-II developing @ 1500 RPM and Alternator, complete with type approved canopy and all accessories. with the following technical specification: *Industries most reliable engines, proven over decades. *Low emission, High efficiency. *Compact, robust and rugged design. *Engine Dry type air cleaner *Exhaust Silencer (Residential type) Hospital Grade. *Expansion bellow *Lube oil cooler Lube oil filter (“Spin-on” type) *Fuel Filter (“Spin-on” type) *In line mono block fuel injection pump with Electronic Governor and fuel feed pump. *Dynamically balanced Flywheel with starter ring *Electronic Governor : Governing class G2 (as per ISO 8528 part V) *SAE 1 flywheel housing and flywheel suitable for SAE 14 disc coupling for close coupling of single bearing alternator.

*Exhaust gas turbocharger 12 Volt electric starter motor 12 Volt, 10 amps. Battery charging alternator *Engine instrument control panel consisting of: Engine safety module EMS (KG934) with built in On/Off Bush button. ALTERNATOR 62.5KVA, Three phase 415V, 0.8 pf 4 wires 50 hz at 1500 RPM brushless alternator. The voltage regulation will be 2 phase sensing +/¬ 1 %. The alternators shall be of Class H insulation, enclosure IP 23 and are designed built and tested to IS 4722 or any other equivalent Indian or international standards. Control Panel: 62.5 KVA DG Set Std Control Panel Consisting of EMS KG934 unit consisting Volt, Amps, RPM, Hz, LLOP, HWT, Low fuel level, over Speed alarm, Over Load alarm, Load imbalance safety alarm, etc. Fuel Tank:150 Letters Capacity inbuilt Fuel Consumption: 100% = 18.8Litres/hr.75% = 13.8Litres / hr.50% = 9.9Litrs/hr. Battery: 12V DC, 130AH Supply of AMF Control Panel Suitable for 62.5KVA DG set for EB Services with byepass arrangement.Supply and Fixing of Exhaust piping with MS pipe along the wall necessary Accessories etc.Transport charges & Charges for laying of above Exhaust pipe & Cladding & DG Set Bed all Civil wirks included Completed etc., (Make: Kirlosker, Koel or equvalent)

Fabrication, Supply, Erection, Testing and Commissioning of whether proof CRCA sheet steel made up of 2mm powder coated MCCB Indoor Type Three Phase Changer Over panel of size (H 1450 X L 1400 X D 400 ) mm with suitable to accommodate 125A 4 pole Three phase Change Over Switch-1No. as incomer for EB Source and as incomer for DG Source , 1no 100A 4Pole MCCB, 1no of 100A 4Pole MCCB, 3nos of 63A 4Pole MCCB's, and 1no spare compartment for as O/G supply with the provisions to accommodate Busbar chamber and cable chamber with size of 33x6mm copper busbar 4 runs having three phase Multifunction meter with line indicators and with all necessary accessories with all other connected works etc. The panel made up of 16/18 SWG CRCA sheet steel comprising of 4 sections with separate sheet steel weatherproof and shock proof safety insulation system conforming to IE Rules with IP protection, and with the panel should be painting by powder coating finishing etc.,as complete and making good of the panel with neat finishing. (Switch make : L & T / ABB) panel should be earthing confirming ISI specifications. The panel should be erected on Anchor fastners, bolts and nuts for mounting the Indoor Panel as directed by engineer-in charge/department superior engineers.

Supply and fixing of 7 segment 6 way TPN MCB sheet steel distribution board (Higher end) with metal /acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and separate 4 way provision for accommodating one no. 40A/32A 4 pole incoming MCB / Isolator and another separate 4 way provision for accommodating one no. 25A, 30MA 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and separate provision for 6A-32A SP MCB / Isolators ( totally 18 nos.) for sub incomers in 3 segments with label holder and provision for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only.

Supply and fixing of 7 segment 4 way 63A TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and seperate provision for MCB / Isolators ( totally 18 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only

Supply and fixing of 8 way vertical TPMCB sheet steel Industrial Type TPMCB DB with IP54 Protection of surface type fitted with bus bars and neutral links with 1 No. of 63A FP MCB as Incoming and 6 Nos.of 32A,10KA Triple Pole MCB in Flush with wall and making good of the concealed portion with earth connection.( Industrial Type TPMCB DB with IP54 Protections)

Supply and fixing of 12way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) 1No. 32A 30 MA 4 Pole ELCB as incoming and 10 Nos. 6A to 32A SP MCB outgoing in flush with wall. The MCB DB and MCB's should be with ISI mark (like standard make)

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 25A FP ELCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only.

Supply and installation of 16M high mast shaft in two sections suitable for 50 m/sec wind speed, with head frame, winch mounting bracket, luminaries carriage suitable to with 2.5 mtr Dia Semi Circular frame (ARM)suitable to install 6 nos of 500W Flood Light LED luminaries with counter weight arrangements , mounting clamp and brackets etc. Raising ,lowering system comprising double drum winch, suitable SS wire rope, trailing cable, connector, integral power tool motor, manual handle, junction box, lighting finial, Lightning spike if require,wiring material from JB to individual luminaire & MCB in base compartment are included and are a part of installation, foundation bolts manufactured from special steel along with nuts, washers, anchor plate and common template. LED Single dome aviation obstruction light, outdoor stand mounted feeder pillar with 63A 4pole RCCB with 100mA, single dial time switch, 45A TP contactor for the automatic switching of luminaries , power tool control with 2 no 9A contactors and raise lower push button, Incoming 35 sq. mm and outgoing 25 & 4.0 sq. mm terminals, shallow foundation with M25 grade concrete for the highmast considering the safe soil bearing capacity at site as 10 T/sqmtr at 2 metre depth with all materials and labour, GI pipe earthing for High mast with 2.5 M long 40 mm dia GI Pipe including connection to High mast earth terminal with 25 x 3 mm GI flats with all materials and labour(2nos per mast required) , wiring of luminaires with all wiring materials like PVC insulated PVC sheathed flexible cable of suitable copper conductor cores of 2.5 sq. mm, lugs, MCB and all labour,mast feeder pillar by grouting the stand in concrete. with all necessary components for the complete functional operation. Contractor to get structural approval from the Civil team for the highmast foundation.

Supply and installation of 9M Mini high mast suitable for 50 m/sec wind speed, with 1.5 mtr Dia Semi Circular frame suitable to install with 3 nos of 250W luminaries with counter weight arrangements , mounting clamp and brackets etc. Internal wiring material shall be from JB to individual luminaire & MCB in base compartment are included and are a part of installation, foundation bolts manufactured from special steel along with nuts, washers, anchor plate and common template. The foundation shall be with M25 grade concrete for the highmast considering the safe soil bearing capacity at site as 10 T/sqmtr at 2 metre depth with all materials and labour, GI pipe earthing for High mast with 2.5 M long 40 mm dia GI Pipe including connection to High mast earth terminal with 25 x 3 mm GI flats with all materials and labour, wiring of luminaires with all wiring materials like PVC insulated PVC sheathed flexible cable of suitable copper conductor cores of 2.5 sq. mm, lugs, MCB and all labour. The rate is inclusive of Freigh Charges, Insurance Cost, Loading and Unloading Charges.Contractor to get structural approval from the Civil team for the highmast foundation.

Supply, erection, testing and commissioning of 6 mtr free standing Single arm bracket of GI Hot Dip Galvanised Octoganal pole. 8 octagonally continuosly tapered strcutured pole with base plate of size 220 x220 x 12mm along with M20 800mm Long J Bolt as per IS-875 along with 60W LED fitting with following specification. Bottom pole dia -130mm,Top Pole dia -70mm , Thickness of pole -3mm.The pole should be hot dip galvanized confirming to BESN ISO - 1461 with thickness of 65 Micron. Construction of pillar accommodating MCB and switch housed in weather proof box including wiring to the light fittings with 2 runs of 2.5 Sq.mm PVC insulated copper conductor, supplying and fixing of Street light SMC Box and 4 way 30 A rated terminal block loop in loop out cable arrangements coil earthing etc. the rate shall included for cable in and out throught GI pipe. The pole shall be as required by the Engineer in charge and complete with suitable pressure die cast aluminum housing also adhering to the above said specifications.Note:-The rate shall be quoted for complete set of Pole, Base foundation,Anchor fastener,internal wiring,earting materials,6A DP MCB box and all necessary accessories and civil cost etc should be provided as suitable to the requirement .

Supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 4 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonry pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 45W LED Top light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED street light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour (45W LED Top Light Fittings)

Supply and Fixing of 120W LED Flood Light Fitting with LED with PVC unsheathed copper leads from terminals to the fitting and Suitable LED Street Light Pipe with suitable Clamps and Crews etc, Complete.(GI) (Make:Crompton/ Philips/Havells)

Supply and Fixing of 48W LED Street Light Fitting with LED with PVC unsheathed copper leads from terminals to the fitting and Suitable LED Street Light Pipe with suitable Clamps and Crews etc, Complete.(GI) (Make:Crompton/ Philips/Havells)

Supply, Installation, Testing & Commissioning of 40W LED Gate Light Fitting. The Light Fitting should be powder coated with high pressure die-cast aluminium LED housing. And the LED fixed on die-cast aluminium heat sink for proper thermal management. and the operating voltage range 140 – 270V AC, provided with open and short circuit protection and input surge voltage protection. Decorative post top for 360 degree Indirect light with IP 65 protection, Resistant to impact and corrosion. Glare-free and better uniformity. MAPLE LPTO-40-CDL/M make :Crompton Features and details Aesthetically designed and soft illumination effectiveness : 2450 lm power : 40W colour : multi colour Included components : post Top Rate shall inclusive of necessary joint kit,glands,etc for loop in/out connection suitable to outdoor application. Crompton CAT REF : - LPTO-40-WW-M Equivalent.

Supply, Installation, Testing & Commissioning of 10W LED bollard light fittings Fitting. The Light Fitting should be powder coated with high pressure die-cast aluminium LED housing. And the LED fixed on die-cast aluminium heat sink for proper thermal management. and the operating voltage range 140 – 270V AC, provided with open and short circuit protection and input surge voltage protection. The driver should be Constant voltage constant current SMPS Protection of Fitting should be IP 66. LED having 50,000 burning hours with minimum 70% lumen maintenance and power factor 0.95. System consumption should be require with lumen package as per requirement. Crompton CAT REF : - LBLA3-10-CDL / Equivalent-(LANDSCAPE LIGHT). rate shall inclusive of necessary joint kit, glands, etc., for loop in/out connection suitable to outdoor application .

Supply and Fixing Round shape surface mounted 40W LED surface variant and A timeless classic, the LUNAR is the top of its class when it comes to large disk feature lighting. With a range of 3 sizes, ide l for modern living spaces where design and interest are upper most. Also available in warm white and natural white with 36 watts LED lamps model equivalent to LCSUR6-40-CDL) ( Make: crompton. Philips, K-lite)

Supply, installation, testing and commissioning of 24W LED (2X2) Surface mounted light fitting with cool day light, made out of CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, suitable for recessed / surface mounting including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.

Supply, installation, testing and commissioning of 18 W LED DOWN LIGHT FITTING with IP55 cool day light suitable for pole mounting, made out CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, including electronic drivers, day light colour LED lamps, inter connecting wiring with suitable fixing clams, hooks as required including accessories all inclusive.

Supply and Fixing of 20W 4' LED Tube Light with PVC unsheathed copper leads from terminals to the fitting. (Make : Philips/Crompton/Havelles )

Supply and fixing of pressure die cast aluminium housing Bulk Head 10W LED fitting with IP65 protected with PVC unsheathed copper leads from terminals to the fitting. model equivalent to Crompton LBHE-10-CDL (Rate as per quotation) (Philips/Bajaj/Crompton/K.Lite )

Supplying, installation, testing and commissioning of 1200 mm (48") sweep AC ceiling fan complete with out modular type stepped electronic 300W regulator, with 1 metre down rod with all required accessories.including point wiring ( 5 STAR )

Supply and fixing of 300mm(12")sweep (Heavy duty) AC Exhaust fan complete with necessary wall opening and making good of the wall and wiring to the near by point with 1.5 sqmm FRLS PVC insulated copper wires including necessary accessories and hardware's as required.

Supply and fixing of louvers shutter arrangements for 300mm(12")sweep (Heavy duty) AC Exhaust fan complete .

The cable rack shall have runners rugs of suitable size, horizontal elbow, vertical elbow 90 Deg. Up vertical elbow 90 Deg. Down, re-deep, coupler plates, materials. The cable racks shall be suspended from ceiling supported from side walls in columns etc. with adequate size supporting angles / channels with fastners, welding, anchor bolts, nuts etc. The rack shall have suitable cable clamping arrangements etc.' Cable Tray /ladder should be powder quoted as match with ceiling colour as per PWD requirements. The rate shall inclusive of necessary Wedge anchors theaded rods,nuts & bolts, making clamp for rcc roof fix / perlin/Truss, cable tray clamps etc,(8 mm threaded rod supports shall be provided at not more than 2 mtr center to center and as per site requirement )

Perforated type

Supply and fixing of GI Hot Dip / Powder Coated 16 SWG Cable Tray with 150mm width and 50mm height

Supplying and fabricating of MS structural steel supports for various applications using U channels, MS angle iron, bolts, nuts, anchor bolts etc., required for the work, cut to the size, bent to shape, welding, grouting etc., complete. Supports shall be powder coated with required colour for different system as mentioned above.

Supply and laying of following XLPE armoured LTUG cable in a trench/Tray with suitable cable tie tag etc as required.

Supply and Laying of 3 1/2 x 70 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 3 1/2 x 50 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 3 1/2 x 35 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 31/2 x 25sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 4C x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and laying of 4CX6sqmm Cu. armoured LTUG Cable in the existing cable trench

Supply and laying of 4CX4sqmm Cu. armoured LTUG Cable in the existing cable trench

Supply and laying of 3CX2.5sqmm Cu. armoured LTUG Cable in the existing cable trench

Supply and clamping of following XLPE armoured LTUG cable on post or on wall MS-Clamps , Saddles, plugs, Screws etc., as required.

Supply and Clamping of 3 1/2 core x 70 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and Clamping of 3 1/2 core x 50 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and Clamping of 3 1/2 core x 35 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and Clamping of 3 1/2 core x 25 Sq.mm PVC armoured LTUG aluminium cable on post or on wall MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and Clamping of 4C x 16 Sq.mm PVC armoured LTUG aluminium cable on post or on wall with MS-clamps, saddles, plugs, screws etc., complete including transport charges of UG cable.

Supply and fixing of double compression brass cable gland for following Aluminium conductor XLPE insulated armoured cable of 1100 V grade with earth connection.

Supply and fixing of brass cable gland for 3 1/2 C x 70 Sq.mm PVC LTUG armoured cable with earth connection

Supply and fixing of brass cable gland for 3 1/2 C x 50 Sq.mm PVC LTUG armoured cable with earth connection (SD-188)

Supply and fixing of brass cable gland for 3 1/2 C x 35 Sq.mm PVC LTUG armoured cable with earth connection

Supply and fixing of brass cable gland for 3 1/2 C x 25 Sq.mm PVC LTUG armoured cable with earth connection

Supply and fixing of brass cable gland suitable for 4C x 16 PVC armoured LTUG cable with earth connection.

Supply and fixing of brass cable gland for 4C x 6 sqmm COPPER cable LTUG cable with earth connection.

Supply and fixing of brass cable gland for 4C x 4 sqmm COPPER cable LTUG cable with earth connection.

Supply and fixing of brass cable gland for 3C x 2.5 sqmm COPPER cable LTUG cable with earth connection.

Supply and providing cable end termination of the following size PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (copper sockets for copper cables and Alu. Sockets for alum. Cable)

Supply and providing cable end termination of 3 1/2 Core x 70 Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete.

Supply and providing cable end termination of 3 1/2 Core x 50Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete.

Supply and providing cable end termination of 3 1/2 Core x 35Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete.

Supply and providing cable end termination of 3 1/2 Core x 25Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete.

Supply and providing cable end termination of 4 C x 16sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping with electrical connection complete.

Supply and providing cable end termination of 4 X 6 Sqmm PVC LTUG Copper cable with necessary copper cable sockets by crimping etc, with electrical connection complete.

Supply and providing cable end termination of 4C X 4 Sqmm PVC LTUG Copper cable with necessary copper cable sockets by crimping etc, with electrical connection complete.

Supply and providing cable end termination of 3C X 2.5 Sqmm PVC LTUG Copper cable with necessary copper cable sockets by crimping etc, with electrical connection complete.

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) ( 4points / Coil).

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection by 1 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for PVC concealed light (6 points per coil) (for rooms like bath, toilet & pumproom, etc.).

Wiring with 3R x1.5 sq.mm. (22/0.3) PVC insulated unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection of 1 run of 2.5 Sq.mm wire and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with painting of suitable colour for concealed PVC pipe Plug point ( 8 points / Coil)

Wiring with 2 x 4 sq.mm. (56/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 16A one way module switch and 1 no. 16A 3/2 pin module socket with module front plate with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with painting of suitable colour for Concealed PVC pipe power Plug point ( 8 points / Coil)

Supply and Run of 2 of 4 sq.mm. (56/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour.

Supply and Run of 2 Run x 2.5 sqmm and 1R of 1.5sq sqmm PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable Pvc conduit pipe on concealed wall and ceiling with continuous earth wire connection with painting of suitable colour.

Supply and fixing of 20A DP Switch With 20Amps 3 Pin Socket With Shutter Type , combined flush type wall socket FOR Split AC unit UNIT in switch along with moulded front plate in G.I anodised manufaturer's mounting box fixed flush with the wall complete with all accessories as required as per the site condition.

Supply and fixing of 2nos.6A two module 5 pin socket , 2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Scope cover wall cutting , grouting , flushing and making good on the wall.

Supply and fixing of manufacturer's GI metal back box and 3 nos of 6A modular switch, 3nos of 6A 3 pin combined modular type wall socket in flush with wall mounted on poly carbonate front plate with switch mounting metal parts, in flush with wall.

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Scope cover wall cutting , grouting , flushing and making good on the wall.

Supplying and Laying of 100 mm dia PVC pipe (6kg / sq.cm.)and relevant specials including packing the joints with rubbers lubricant with necessary connections to fittings etc., complete in all respects as directed by the departmental officers.(Rate as per Quotation)

Supply and fixing of thermoplastic loop - in and loop out boxes with lid of dimension min 104X104X70MM with 20A connector. shorting link 2 way necessary and along DIN rail terminal block. The Junction Box shall be insulated and made out of high grade thermoplastic. The JB shall be IP Rated for outdoor applications, environment friendly, recyclable, UV resistant, halogen & silicon free, anti acid& anti corrosive. The JB shall be rated for Degree of Ingress Protection IP 65 in accordance with IEC 60529.

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 50mm and 2 mtr long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs of carbon based environment friendly backfill compound and suitable clamp and with copper earth plate of size 125mm x 50mm x 6mm with necessary funnelling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply, Installation, Testing and Commissioning of earthing station consisting of 600 x 600 x 3 mm. thick, copper Plate earth electrode, back filling with alternate layer of charcoal, salt, brick masonry work for chamber 450 x 450 mm. heavy duty CI cover, watering pipe, funnel and earthing conductor as per IS:3043 specification. All civil works required such as excavation in all types of soils, rocks, PCC Earthing Chamber foundation, reinstatement and making good the surface to match original, removal of surplus earth etc. are included.

Coil earth to street light poles with No.8 SWG GI wire of 11.5 metres of length in which 10 metres of total length compressed in to a coil of one meter length (75mm to 100mm dia) connected suitable with hexagonal earth bolt of size 8mm in to 25mm welded on the pole at one end with a coil position fixed on the earth.

Supply, fabrication, of GI /Copper earth flat of following size in provided trench, clamping in wall, ceiling, with suitable Clamps/ saddles, connecting the joints through bracing / welding covering with bitumen paint including accessories wooden plugs, screws, fastener etc., all inclusive

Supply and run of 25mm x 6mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection

Supply and run of 25mm x 6mm GI flat with necessary clamps / supports on wall / floor / ground for earth connection

Supply and Run of No8 SWG copper Wire for earth Connection

Supply and Run of No8 SWG GI Wire for earth Connection

Supply and Run of 2 of 10 sq.mm. (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with painting of suitable colour.

LIGHTING ROD Supply of Early Streamer Emission Air Terminal (ESEAT). Model: L The ESEAT has corrosion resistant stainless chrome body made up of AISI 316 grade of height 0.50 metres capable of working in hazardous atmosphere. The Air terminal is non-radioactive and requires no special licensing. The unit is fully autonomous (no battery, no external power supply is required), collects energy from the ambient electric field. The ESEAT model has been tested in a high voltage laboratory in accordance with NFC 17 102 in order to measure the average gain in triggering. The average gain in triggering time (ΔTs) obtained during the lab test for the offered model is 60 μs. The ESEAT works on negative as well as positively polarized discharges. ESEAT has been tested for such discharges in Central Power Research Institute (CPRI). A dedicated tester is available to test the healthiness of the ESEAT on request (Page No. 37, Point No. 3 of Clause 8.6 of the Revised NFC 17-102 version 2011 ).ESEAT Model : L - Radius of protection : 86 Metres Level of protection considered for the Project-II level

MOUNTING STRUCTURE Supply of Standard / Special Mounting Structure of height 4.5 mts. pipe, and 300 x 300 x 8mm MS plate, 3 mts. 48mm OD class C GI outer pipe,1.8 mtr, 38mm OD inner pipe, for roof mounting on concrete base and with FRP adapter

TEST LINK Supply of Test Link Box for each Down conductor in order to disconnect the earth termination system to enable measurement of resistance

Supply and installation maintenance free GI Earthing System comprising of 50mm dia and 2 mtr. long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs. of carbon based environment friendly backfill compound and suitable clamp

SURGE PROTECTION Supply and installation Cabinet Type Class 1 and 2 Combined Model SPD to arrest surges and overvoltages in the power line due to lightning switching action etc. they must be installed in the incoming MCC panel / DB of the respective building in parallel to the power circuit. Model: PSV4-12.5/400TT (3 phase power network)

FIRE SAFETY

First Aid Box complete with all First Aid Medicines (M-1977)

Shock Treatment Chart fixed in glass frame (M-1978)

Fire Extinguisher Co2, 4.5 kg. confirming to TAC Norms (M-1982)

Danger Board as required by the Electrical Authorities (M-1981)

2m x 1m Rubber Mat suitable for 11 KV installation confirming to IS

Supply and kept in position of 9 litres capacity Fire Buckets of 4 Nos. with Bucket Stand as per standard specifications and as directed by the Departmental Officers

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Supply and fixing of Carbon-di-Oxide Gas Type 2 kg. capacity Fire Extinguisher as per New IS15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc., complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT /SAFETY FIRST / EQUIVALEN

CCTV System

Supply, Installation, Testing and commissioning of 32 channel 8 SATA NVR, with 6T Hard Disk Drive 4 nos, New logical and visualized GUI design Dual-OS design to ensure high reliability of system running, ANR technology to enhance the storage reliability when the network is disconnected, Configurable normal or hot spare working mode to constitute an N+1 hot spare system Video Input and Transmission, Connectable to the third-party network cameras Compression and Recording, H.265+ compression effectively reduces the storage space by upto 75%, Full channel recording at up to 12MP resolution HD Video Output  HDMI1 / VGA1 outputs provided  HDMI1 Video output at up to 4K ( 3840 × 2160 ) resolution Storage and Playback, Upto 16 SATA interfaces and 1 eSATA interface for HDD connection, Support upto 10TB capacity for each HDD, Smart search for efficient playback. and smart playback to improve the playback efficiency,Supports VCA search for fire/ship/temperature/temperature difference detection triggered video files, POS information overlay on live view and playback, POS triggered recording and alarm Network & Ethernet Access  Hik-Connect for easy network management, 2 Gigabit Ethernet network interfaces. (Make : Hikvision / Dahua / Sony

Supply of 8MP, Internet Protocol fixed BULLET CAMERA with following specification: ●1/2.5" Progressive Scan CMOS, ● 3840 × 2160 @15 fps,2.8/4 mm fixed lens,01 lux @ (F1.2, AGC ON), 0.028 lux @(F2.0, AGC ON), 0 lux with IR, H.265+, H.265, H.264+, H.264, 2 Behavior analyses ( Line crossing detection, intrusion detection) ● Face Detection ● 120dB WDR, ● BLC/3D DNR/ROI, IP67 complied ●On-board Storage - Built-in micro SD/SDHC/SDXC card slot, up to 128 GB, ● Shutter Speed 1/3 s to 1/100,000 s, ● 3-Axis Adjustment Pan: 0° to 360°, tilt: 0° to 100°, ● rotate: 0° to 360°, 2.8 mm, ● horizontal FOV: 102°, vertical FOV: 53°, diagonal FOV: 124°, ●Lens Mount M12 ● IR Range I5: up to 50 m, ● Image Settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser, ● Power Consumption and Current-12 VDC, 0.7 A, max. 7.5W PoE: (802.3af, 36V to 57V), 0.3 A to 0.2 A, max. 9W ● Camera out fitted with metal housing so as to prevent the lens from damages during physical abuse. (Make: Dahua/Panasonic)

Supply ,Testing and Commissioning of Dom Camera 8MP IR camera

Supply, Installation, Testing and Commissioning of 55" smart LED TV with following specifications a) Full HD 1920 x1080 (4K monitor) b) IPS pannel c) Slim back light LED module d) 900 PMI e) Triple XD engine f) Dynamic scanning g) ANR h) True colour generator i) 8modes of picture j) picture wizardIII k) Real cinema 24P l) HDMI -3nos m) USB -3nos n) Built in LAN o) Magic remote p) Dimension 1242 x 724 x 55.1min(37). (Make: Sony/ LG /Samsung).

Supply and fixing of outdoor 4X6 PVC box with 102mm x 77mm x 102mm with all fixing accessories.

Supply and Clamping of CAT 6 armoured cable in suitable PVC Pipe 1" thick on wall / ceiling with connected PVC accessories with clamps, saddles etc., complete. (Between ethernet switch to camera and radio modem) i. Application : Primary (Campus), Secondary (Riser), Tertiary(Horizontal) IEEE 802.3 : 10Base-T; 100Base-T; 1000Base-T IEEE 802.5 16 MB; ISDN; TPDDI; ATM ii. Standards: ISO/IEC 11801 2nd ed.; IEC 61156-5 2nd EN 50173-1; EN 50288-6-1,EIA/TIA 568C.2, RoHS Compliant. Fire Rating: PVC : IEC 60332-1. iii. Conductor - Bare Copper Wire iv. Insulation - Polyethylene v. Twisting - 2 Cores to the pair vi. Cable lay up - 4 Core to the pair It has diameter of (23 AWG) 0.550 ± 0.015.Insulation : Polyethylene.GI wire of size is 0.90 ± 0.030mm.

Fixing and Termination of CAT 6 Cable RJ 45Jack Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply and fixing of 24 Port 2SFP with Module, PoE Giga Range Lan Switch.• 24 Ports 10/100/1000 Base-T PoE + 4 x Combo Gigabit UTP or Gigabit SFP slots • Support IEEE 802.3af (PoE) and 802.3at (PoE+) Standard • Equipped with IEEE 802.3az Energy Efficient Ethernet (EEE) Complaint • Support IEEE 802.1Q VLAN traffic segregation • Access Control List (ACL) feature to enhances network security • Auto Surveillance VLAN for easy integration with IP-based surveillance systems • Loopback detection (LBD) and broadcast storm control to avoid network downtime • Quality of Service (QOS) and bandwidth control to ensure smooth operation • Support Web-based GUI, Smart Console , Network Assistance Utility • Cable diagnostics function to help troubleshooting wiring problem including Optical Fiber Cable connecting network accessories. (Make: DLINK, NETGEAR,TPLINK)

Supply and fixing of POE 8 port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line. (Make: DLINK,NETGEAR/ TPLINK)

Supply and fixing of Out Door Wheather Proof Box 2Ft x 2Ft Out Door Wheather Proof Box 2Ft x 2Ft

Supply and Fixing of Rack with Accessories -Higher end 42 U Rack with LIU unit and fan extra for the above rack.

Supply and fixing of 2 feet CCTV Camera Stand with attachment fittings as follows: * Weather heads and couplings * Cabinet mounting fittings, plates, brackets as needed. * Reinforced couplings for wire entrances to cabinets.

Supply and Instalatin for 2KVA UPS with Battery, Single Phase UPS (Single Phase In & Single Phase Out) Capacity - System with Battery - 2Hours back up

Supply and Instalatin for 1KVA UPS with Battery, Single Phase UPS (Single Phase In & Single Phase Out) Capacity - System with Battery - 1 Hours back up

Supply and fixing of 6m Length pole with base plate of size 250x250x6mm as per IS-875 with following specification. Pole Outer die -76.10mm x 3.65mm Thick x 6 meter.

Supply and filling in foundation and basement with M sand / filling sand in layers of not more than 15cm thick well watered, rammed and consolidated etc., complete as per standard specification.

Providing and relaying Plain Cement Concrete 1:2:4 (One cement Two sand and ten broken Machine crushed stone jelly ) using HBG Machine crushed stone jelly of size 20mm gauge for founding and basement including de-watering if found necessary and laid in layers of not more than 15cms thick etc., complete complying with standard specification and as directed by the departmental officers.

Supply and Laying in position the best quality and 40mm dia HDPE pipes of ISI mark etc., with standard specification.

PA System

Supply and Installation of 15 watts indoor Wall Speaker with Line Matching Transformer in the existing pole with supporting clamp Model:- Specification:- 1.Input Power : 15W RMS/20W Max 3. Frequency : 250-10,000Hz 4. SPL : 108dB/1W/1m,122dB/25W/1m at 1kHz 5. Power Taps : 40/30/20/10/5W (Make: Ahuja, Bose, Yamaha or equivalent) (Make: Ahuja AMH402T/Bosch or its equivalent)

Supply, Installation,Testing & commisioning of 480 watts P.A Mixer Amplifier with the output power of 1350 watts maximum, 500watt rms at 10% Thyristor harmonic distortion(THD), 850watt RMS at 5% THD, 800 watts RMS at 2% THD and the power supply AC voltage ranging from 220-240 volt, 50/60 hertz. with the DC input of 48 volt and 1000watts has tone controls of Bass=+- 10 db at 100 hz weighing 42kg with the speaker output of 2Q,4Q.70volt&100volt has power consumption of 1600VA AC &12A DC and 100db output regulation at 1khz no load to full load ratio. The signal to noise ratio is 60db with the imnput channels of 0.8mv/4.7kq,3*Aux 100mv/50kq.The frequency response of 50-15000hz+-3db.(Make:Ahuja SSA 10000 /Bosch or its equivalent)

Supply,Installation, Testing & Commisioning of 10" gooseneck with suitable base incorporates separate bush switches for momentary and dynamic microphone with 600ohm impedence and has 2.5mv/pa sensitivity and frequency response ranging from 50-15000hz with multi tone chime model.(Make:-ACM66 Ahuja/bosch/its equivalent) (

Supply and run of Armoured Speaker Cable 2 core 1.5 sqmm PVC insulated SC unsheathed of 1100V Grade in suitable PVC conduit pipe on concealed wall and ceiling with painting of suitable colour.

Supply & Installation of custom built M.S Powder coated wall mounting Audio rack with Lock & key for housing of Amplifier & player/Recorder conforms to EIA-310,IEC-60297 and able to withstand the load of 40kg with welded construction made up of CRCA steel with suitable height, width and depth.

Supply,Installation, Testing & Commisioning of Cordless mic UHF model.(Make:-ACM66 Ahuja/bosch/its equivalent)

KONGU CONSTRUCTION AND CONTRACTORS