Construction of VDWC on the fourth and fifth floors of the proposed family court cum mediation centre (G+3) Building at civil court Supaul District.

Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of al! rubbish with all leads and lifts.

Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed.

Extra for every additional lift of 1.5m or part thereof in:

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead

Close timbering over areas including strutting, shoring and packing, cavities (wherever required) etc. complete. (Measurement to be taken of the face area timbered):

Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l.

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level

1:2:4 (1 Cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size)

Extra for providing and mixing water prooding material in cement concrete work in the proportion recommended by the manufacturers.

Extra for providing and mixing water proofing material etc all complete jobs.

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering, finishing and reinforcement-All work upto plinth level

Reinforced cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finishin and reinforcement.

Reinforced cement conrete work in beams,suspended floors, roofs having slope upto 15, landings,balconiec, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excludingthe cost of centring, shuttering, finishing and reinforement with 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size).

Add or deduct for providing richer or leaner mixes respectively at all floor levels.

Brick work with bricks of class designation 100A in foundations and plinth in

Brick work with bricks with fly ash bricks as per IS 12894(2002) & 3495 in foundation and plinth in :

Cement mortar 1:6 (1 cement: 6 coarse sand)

Cement mortar 1:4 (1 cement: 4 coarse sand )

Extra for Brick work in superstructure above plinth level upto floor V cum Cement mortar 1:6 (1 cement: 6 coarse sand )

Half brick masonry with bricks of class designation 100A in foundations and plinth in : Cement mortar 1:4 (1 cement: 4 coarse send). Extra for half Brick masonry in superstructure above pinth level uptofloor V level.

Extra for half Brick masonry in superstructure above pinth level upto

Centring and shuttering including strutting,propping etc. and removal of form for.

Foundations, footings, bases of columns etc. for mass concrete.

Suspended floors, roots, landings, balcnies and access platform.

Lintels, beams, plinth bams, griders, bressumers and contilevers.

Columns,Pillars, Piers, Abutments, Posts and Struts

Stairs,(excluding landings) except spiral-staircaces

Weather shade,Chajjas, corbels etc. including edges

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

Thermo-Mechanically Treated bars TMTC-500-8mm dia.

Thermo-Mechanically Treated bars TMTC-500-10mm dia.

Thermo-Mechanically Treated bars TMT Fe-500-I2mrn dia.

Thermo-Mechanically Treated bars TMT Fe-500-16 mrn dia.

Thermo-Mechanically Treated bars TMT Fe-500-20 mrn dia.

Thermo-Mechanically Treated bars TMT Fe-500-25 mrn dia.

12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of near cement

15 mm cement plaster 1:3 (1 cement: 3 coarse sand ) finished with a floating coat of neat cement on the rough side of single or half brick wall.

15 mm cement plaster on rough side of single or half brick wall of mix.

1:4(1 cement: 4 coarse sand )

1:6 (1 cement: 6 coarse sand)

20 mm cement plaster (1:4) etc all complete jobs.

1:6(1 cement: 6 coarse sand)

1:4(1 cement: 4 coarse sand)

Size of Tile 60x60 cm

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles 400x400 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such as white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing 20mm thick mirror polished, machine cut for kitchen platforms, vanity counters facias and similar locatins of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement :4 coarse sand) with joints treated with white cement, mixe* with matching pigament-epoxy touch ups. including rubbing, curing etx. complete at all Ibevels.

Extra for providing edge moulding to 18 mm thick marble stone counters, Vanities etc. over item no. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in -charge.

metre

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen sink in kitchen platform, vanity counters and similar location in marble / granite/stone work including necessary holes for pillar taps etc. including rubbing and polisheg of cut edges etc. complete.

Structural steel work riveted or bolted in built up sections, trusess and framed work, including cutting,hoisting,fixing in position and applying a priming coat of approved ateef primer all complete.

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with G.I.J. or L hooks . Bolts and nuts 8 mm dia. G. 1. limpet and bitumen washers complete.

metre

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washa ble distemper of approved brand

Applying one coat of cement primer of approved brand and manufacture on wall surface:

Finishing walls with Acrylic Smooth exterior paint of required shade :

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal ofwooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-Charge.

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished 12 mm cement plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

metre

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Coupler, 110mm

Single Tee withdoor, 110x110x110mm

Band 87.50, 110mm band

Shoe plain, 110mm shoe

Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing M.S. rivets of sizes in position.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm, modulus of elasticity 900 N/mm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for Separately).

metre

Providing and fixing 35mm thick factory mode laminated veneer lumber door shutter conforming to IS:14616 & TADS 15-2001 (part B),manufactured in factories by approved manufacturers, including black enamelled M.S.butt hinges with necessary screws as per directions of Engineer in charge and panelling with panels of:

35 mm thick

Providing and fixing in position collapsible steel shutters with vertical channes 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T-tron 40x40x6 mm with 40 mm dia steel pulleys complete with bots.nuts locking arrangement stoppers handies including applying a priming coat of approved steel primer.

Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels)made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm)

Extra for providing heavy sheet float glass panes instead of ordinary float glass in glazed doors,windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia wire and 1.4 mm wide aperture with matching wood beading

P/F factory made door frame of PVC 48x40x1.5mm

P/F factory made door shutter of PVC, 30mm thk Factory made shutters with styles, rails and panels of PVC extruded sections in white, grey or wooden finish

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :

Providing and fixing alluminium handles anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc. complete:

Providing and fixing bright finished brass 100 mm mortice latch and lock with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868)aluminium lever with necessary screws etc.completefBest make of approved quality

Providing and fixing alluminium sliding door bolt anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with nuts and screws etc. complete:

Providing and fixing alluminium sliding tower bolt anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with nuts and screws etc. complete:

Providing and fixing alluminium hanging floor door stopper anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc.complete:

Providing and fixing M.S. grills of requirement pattern in frames of windows etc. with M.S. flats, square or round bars etc.all complete

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.).

Applying priming coat:

Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade:

Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. Clear depth and 250mm apron including cost of E/W. involved with 75mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base.the drain duly.plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l,

Making plinth protection 50mm thick of cement concrete (1:3:6) , 1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti-termites' treatrnent(including the cost of chemical emulsion

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.

Providing and fixing skirting with Pre-laminated (one side decorative and other side balancing lamination) flat pressed 3 layer or graded particle board (medium density) Grade I, Type II, IS :12823 marked, with necessary fixing arrangements and screws, including drilling necessaryholes for rawl plugs etc. and priming coat on unexposed surface complete

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

38 mm thick parquet (wood block) flooring of 1st class teak wood laid over 25 mm thick levelling layer of cement concrete 1:2:4(1cement:2 coarse sand:4 store aggregate 10 mm nominal size) to be paid separately coated with a thin layer of hot bitumen of hot bitumen (blown type) @ 2.45 kg per sqm. including fixing blocks in position After dipping in hot bitumen (blown type) up to half depth ,planed levelled smooth and finished complete .

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners.all necessary fittings completejncluding applying a priming coat of approved steel primer.

Providing and fixing steel glazed doors, windows and ventilatrs of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1:3:6(1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with woodenplugs and screws or raw) plugs and screws or with fixing dips or with bolts and nuts as required, including providing and fixing of glass panes with glazing dips and special metal-sash putty pf approved make complete including applying a priming coat of approved steel primer; excluding the cost of metal beading and other fitting except necessary hinges or pivots as required

Extra for providing and fixing steel beading of approved shape and section with screws instread of glaxing clips and met. Sash putty in steel doors, windows, Ventilators and comosite units.

Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete

Providing and fixing in position precast R.C.C. manhole cover and frame of required shape and approved quality.

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal\ size) as per standard design

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed protions of W.C. kitchen and the like consisting of :

Providing and laying integral cement based water proofing treatment including prepatation of surface as required for treatment of roofs, balconies , terraces etc, consisting of following operations. (a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water -proofing compound cleaning the surface before treatment, (b) Laying cement concrete using broken bricks / brick bats 25 mm to 100 mm size with 50 % of cement mortar 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 over 20 mm thick layer of cement mortar of mix 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water froofing compound conforming to IS 2545 to reuired slope and treating similary the adjoining walls upto 300 mm height including rounding of junctions, or walls ad slabs. (c) After two days of proper curing

With average thickness of 120 mm and minimum thickness at khurras point to be 65 ..

Providing and fixing soil, waste and vent pipes.

Cement concrete flooring 1:2:4(1 cement:2 coarse:sand:4 graded stone agregate) finished with a floating coat of neat cement including cement slurry, etc. but excluding the cost of nosing of steps etc. complete

Cement plaster skirting (upto 30 cm hieght) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement

Providing and fixing white vitreous china water closet squatting pan (Indian type WC pan) with 100mm sand cast Iron P or S Trap, 10 litre low level PVC flushing cistern (of approved make) with fittings CI/MS brackets, 32 mm diameter flush pipe with fittings and clamps, over flow arrangement with specials and mosquito proof coupling of approved municipal design including painting of fittings and brackets, cutting and making good the walls and floors wherever required.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

Providing and fixing white vitreous china wash basin with C.I. / M.S. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required.

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing 600 x 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers comelete.

Providing and fixing toilet paper holder:

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gms.

Providing and fixing soil, waste and vent pipes.

Providing and fixing M.S. holder bat clamps of approved design to sand cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) including cost of cutting holes and making good the walls etc.

Providing and fixing plain bend of required degree

Providing and fixing single equal plain junction of required degree with acesses door, insersion rubber washer 3mm thick, bolts and nuts complete.

Providing and fixing terminal guard.

Providing and fixing collar

Providing lead caulked joints to sand cast iron / centrifugallly cast (spun) iron pipes and fittings of diametre:

Providing and fixing M.S stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diametre.

Providing and fixing sand cast iron trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors.

Painting sand cast iron/centrifugally cast (spun) iron soil waste vent pipes and fittings with paint of any colour such as chocolate gray or buff etc. over a coat of primer (of approved quality) for new work.

merter

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Metre

Metre

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for therma expansion.(SW)

Coupler

Single tee with door

Shoe plain

Providing and fixing G.I. pipe complete with G.I. fittings and clamps, including, cutting and making good the walls etc. (internal work)

15 mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40 mm dia nominal bore

Painting of exposed pipes with two or more coats of synthetic enamel paint of approved quality over a coat of red oxide zinc cromate primer including painting of legends in English with direction arrows.

15 mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40 mm dia nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

15mm nominal outer dia pipes

20mm nominal outer dia pipes

Providing and fixing brass stop cock of approved quality :

15 mm dia

20 mm dia

Making connection of G.I distribution branch with G.I main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete.

25 to 40mm nominal bore

50 to 80mm nominal bore

Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end).

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

Providing and fixing gun metal non-return valve of approved quality (screwed end).

Providing and placing on terrace (at all floor levels) polythylene water storage ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing PTMT grating of approved quality and colour.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy aluminium rod with L.P / H.P.H.D plastic ball.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS : 8931

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

Providing and fixing uplasticised PVC connection pipe with brass unions:

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms

Excavating trenches of required width for pipes, cables etc. Including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5M including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering, etc.And disposing of surplus excavated soil as directed within a lead of 50 m Hard/dense soil.

Metre

Providing, laying Non pressure NP2 class (light duty) RCC Pipes with collars jointed with stiff mixture of cement mortar in the propoertion of 1:2 (1 cement : 2 fine sand) including testing and jointing etc complete.

Metre

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

With F.P.S. bricks (For Storm water)

With F.P.S. bricks (For Sewer)

Extra for depth for manholes

F.P.S. bricks (For Storm water)

F.P.S. bricks (For Sewer)

Boring /drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in IS : 2800 (part I), including collecting samples form different strata, preparing and submitting strata chart / bore log, including hire & running Charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-Charge, upto 90 metre depth below ground level, all type of soil.

metre

Boring / drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in IS : 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer - in-Charge, beyond 90 metre & upto 150 metre depth below ground level.

metre

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.

100mm nominal size dia

150 mm nominal size dia.

100 mm nominal size

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

metre

Gravel packing in tubewell construction in accordance with IS : 4097, including providing gravel fine / medium / coarse , in required grading & sizes as per actual requirement , all complete as per direction of Engineer - in-Charges.

Development of tube well in accordance with IS : 2800 (part I ) and IS : 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by 'V' notch method or any approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory,i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threated mild steel cap or spot welded plate to the top of bore well housing / Casting pipe, removable as per requirement, all complete for borewell of :

100 mm dia

150 mm clamp

Providing and fixing M.S. clamp of required dia to the top of casing / housing pipe of tube well as per IS : 2800 (part I ), including necessary bots & nuts of required size complete.

Providing and fixing Ball plug / Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS : 2800 (Part I)

S/F/F 2 H.P. Cromption or any other apprioved make Motor and ISI make automatic starter mounted on a common wooden board etc. all complete job.

Trenching in ordinary soil upto a depth of 60 cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge of/and manure before and after flooding trench with water (including cost of imported earth,sludge or manure).

Supplying and stacking of good earth at site including royalty but excluding carriage (earth measusred in stacks will be reduced by 20% for payment).

Supplying and stacking Sludge at site including royalty and carriage (Sludge measusred in stacks will be reduced by 8% for payment)

Supplying and stacking a' site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment). Screened through sieve of l.S. designation 4.75 mm

Rough dressing the trenched ground including breaking clods.

Uprooting weeds form the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.

Fine dressing the ground

Spreading of sludge, dump manure or/and good earth in required thickness (Cost of sludge, dump manure or/and good earth to be paid separately).

Mixing earth and sjudge or manure in porportion specified or directed.

Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more tili the grass forms a thick lawn free form weeds and fit for mowing including supplying good earth if needed. In rows 5 cm apart in either direction.

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20 % 1 part of stacked volume of manure after reduction by 8 % ) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure sludge or extra good earth if needed to be paid for separately)

Holes 1.2 m dia. And 1.2 m deep.

Holes 60 cm dia And 60 cm deep

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8 :1 (8 parts of stacked volume of earth after reduction by 8% ) flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed, within a lead of 50 m lift upto 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Plantation of trees

Shrubs / Creeps

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc.as required

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc.as required.

Wiring for light/ power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 No 4 sq.mm. FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface /recessed PVC conduit as required.

Metre

Metre

Metre

Metre

Metre

Supplying and fixing PVC/G.I box of 200mm x 250mm x 60mm deep on surface or in recess with suitable size of phenolic laminated sheet cover in fornt including painting etc as required.

Supplying and fixing PVC/G.I box of 75mm x75mm x 50mm deep on surface or in recess with suitable size of phenolic laminated sheet cover in fornt including painting etc as required.

Supplying and fixing suitable GI Box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc. as required. (for power plug )

Supplying and fixing suitable size G.I Box with modular plate and cover in front on surface in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc., as required. (for light plugs to be used in non residential buildings )

Supplying and fixing modular type 2 pin telephone socke/ speaker outlet on the existing modular plate & box including making connection,excluding moduler plate etc. as required.

Supplying and drawing 2 pair 0.5 sq mm. FR PVC insulated copper conductor telephone cable through existing PVC concuit including connection, testing etc. as required.

Supplying and drawing low resistance co-axial T.V cable RJ-6 grade 0.7mm solid copper conductor PE insulated shielded with fine tinned copper braid and protected with PVC sheath in the existing PVC concuit etc. as required.

Supplying and fixing modular T.V antenna socket on the existing modular plate and metal box including making connection, etc. as required.

Supply fitting fixing of electronic musicle call bell suitable for single phase 230 volts, complete etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & box excluding moduler plate etc. as required.

Supplaying and fixing 2 pin 5a celling rose on the existing junction box/PVC box including connection etc.as required.

Supplying & fixing brass batten/angle holder including connection etc. as required.

Supply & fixing 2+ 8 way double door SP & N, sheet steel, MCB distribution board, 240 volts, on surface/ in recess, complete with tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc.as required (But without MCB / RCCB / Isolator) Lighting DB

Supply & fixing 4 way(4+12) double door TP & N, sheet steel, MCB distribution board, 415 volts, on surface/ in recess, complete with tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc.as required (But without MCB / RCCB / Isolator) Power DB

Supply and fixing following rating and capacity 4 pole MCCB in existing panel board. Including drilling hole in cubical panel, making connection etc.as required.

P/F following capacity busbar chamber with 4 strips of suitable size made of copper, heavy duty complete with all accessories including connections, earthing the body etc. as reqd.

Supply and fixing 200 A 4 Pole on load / panel moumted change over switch in existing cubical panel board making connection, earthing the body etc.as required

Supplay and fixing wall /floor mounted cubicle panel board fabricated with 16 gauge iron sheet suitable for panel mounted switch discconnector including Bus bar chamber insulator and painting etc as required.9but without bus bar copper strip)

S/F digital voltmeter three phase existing cubicle panel board including drilling holes in the panel board making connection etc.

S/F digital ammeter three phase existing cubicle panel board including drilling holes in the panel board making connection etc.

Supply and Installation of regular/standard module AC ceiling fan of 1200 mm sweep including wiring the down rod of standard length 9 upto 30 cm ) with 1.5 sq mm FR pvc insulated copper conductor etc as required.

Supply and Installation of 300 mm 230 volt AC exhaust fan in the existing opening including making good the damage connection testing commissioning etc as required.

Supplying and fixing single wall mounted 20/22 watt LED type batten fitting complete with electronic driver and LED tube etc directly on wall/ ceiling including connections with 1.5 sq.mm FR PVC insulated copper conductor and earthing the body etc. as required.

Supply and fixing Bulk Head Fitting die cast aluminium alloy body with prismatic glass cover suitable for the GLS / CFL L , directly on wall / ceilling including connection etc. as required.

Supplying and fixing indoor recess mounting 36 watt LED flat panel luminaire suitable for armstrong / grid ceiling and complete with electronic driver etc. irectly on false ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supplying and fixing single wall mounted 18/22 watt LED type batten fitting complete with electronic driver and LED tube etc directly on wall/ ceiling including connections with 1.5 sq.mm FR PVC insulated copper conductor and earthing the body etc. as required.

Supplying and fixing 90 watt LED type street light with die cast aluminium housing for ingress protection of IP65 and complete with all accessories etc, on pole/building including connection with FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supply and erection of 6 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 130 mm, made of 3 mm thick sheet along with base plate of size 220 X 220 X 12 mm , small door opening for junction box mounting with MCB & connector, cement concrete of 1:3:6 including excavation, refilling and suitable size foundation bolts with template and all complete job as required. (but without pole collar)

Providing chemical/mineral maintenance free earthing system comprising of copper coated earth electrode 3 metre length and 17.2 mm outer dia along with 25 kg earth conductivity enhancing back fill mineral compound for earth electrode to fill up the excavated earth and earth inspection pit etc. as required. Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc. as required. Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing etc. as required.

Supplying of XLPE/PVC insulated Sheathed (Heavy Duty) armoured electric cable with aluminium conductor of 1.1 KV graded con. IS 1554 Part I upto date amendment etc as required of following size

Metre

Laying of one number PVC insulated and pvc sheathed /XLPE power cable of 1.1 kv grade of following size direct in ground including excavation sand cushioning protective covering and refiling the trench etc as required.

Metre

ABC Powder Type (Stored Pressure) Fire Extinguisher, 4 kg. Capacity, ISI mark (IS:15683), squeeze grip valve, operating temperature (+5) degree Celcuis to (+55) dgree Celcuis for Class 3A Type of Fire Filled with MAP ABC Powder, Complete in all respect

CO2 Type Fire Extinguisher, 4.5 Kg Capacity, ISI Mark (IS:15683) squeeze grip valve, operating temperature (-30) deg Cel to (55) deg cel. For Class 13B type of Fire Fitted with 1 Mt. Hose & PVC Horn, Complete in all respect.

SITC of 1.5 Ton 5 Star Inverter Split AC copper coil . with Stablizer (NOTE:- Air Conditioning System and its accessories should note have Made in CHINA or Any CHINEASE accesories ) Make must be of Would Class Standard. (HITACHI/DAIKIN/TOSHIBA/MITSUBISI/O General or Eqvt )

SITC of 1.0 Ton 5 Star Inverter Split AC copper coil with Stablizer . (NOTE:- Air Conditioning System and its accessories should note have Made in CHINA or CHINEASE accesories ) Make must be Would Class Standard. (HITACHI/DAIKIN/TOSHIBA/MITSUBISI/O General or Eqvt)

SITC of 2 Ton inverter Cassette AC 5 star with all accessories & all comlete work.( Make- blue star/mitsubishi/lg/carrier/Hitachi)

Extra copper pipe

Extra Drain Pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.

Meter

Supplying, installation, testing and Commissioning of passenger Car Type Elevator (lifts) 8/544 Kg-1 MPS (for FOUR stop, G+3 One No. lift) with fan, fully automatic state of the art technologies, make from World Fame manufactures (Make:- Thyssen/ MITSUBISI/ SCHINDLER/KONE/JOHNSON/OTIS is Banned for Bad Service Regulation. with all complete job .

Maintenance Cost for 5-Years (CAMC) with Tax :-Note :- Maintenance/Replacement of all Parts included.

Supply / Installation and Commissioning of 24 Port Network Switch GIGA PoE,IEEE 802.3at and IEEE 802.3af Power over Ethernet (PoE) compliant,24x10/100/1000 Mbps Auto-MDIX PoE ports,Provides up to 30 watts per PoE port,PoE power budget 370W,4 KV surge protection for PoE ports,IEEE 802.3x flow control support,Plug-and-play installation,8.8 Gbps switching fabric,2.75 Mbits RAM Data Buffer,4K MAC address entries,Sturdy metal enclosure

Category 6, UTP 24-Port Patch Panel Size - 482.6mm x 44.2 (19’’ x 1U), Panel Material - Steel-fully powder coated, Unshielded - RJ 45, Plug Insertion Cycle - 750 times DC Resistance- 72Ω max, Voltage Rating - 72 Vdc max, Current Rating - 1.5A max

Supply / Installation and Commissioning of Junction Boxes, Outdoor Box for Camera

Supplying and fixing of RJ 45 computer socket suitable for Cat 6 on module GI box along with base & cover plate in surface or in recess including making connection, soldering etc. as required.

Category 6 UTP Patch Cords - 1 Mtr Standard Colour - Blue, Grey, Yellow, RJ45 Plug - Polycarbonate plug, Current Rating - 1.5A max, Insulation Resistance - 500MΩ/km(min)@500 Vdc, Contact Resistance - 15 mΩ (max) per contact

Category 6 UTP Patch Cords - 2 Mtr Standard Colour - Blue, Grey, Yellow, RJ45 Plug - Polycarbonate plug, Current Rating - 1.5A max, Insulation Resistance - 500MΩ/km(min)@500 Vdc, Contact Resistance - 15 mΩ (max) per contact

Supply fitting fixing Rack 19" 12U fully powder coated complete etc as required with complete accessories (5 amp x 6 socket, wire manager, rack fan) VALRACK/ Netrack make. Wit all necessary items.

Supplying and drawing of UTP 4 pair CAT 6/Cat 6 E LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.

Smart-UPS On-Line, 5.4 kW / 6 kVA with 1 hour Backup12 V 65 AH SMF Battery UPS Toplogy Double Conversion On-Line, Power Rating (VA / Watts) 5400Watts/6000VA, Form Factor Rack/Tower Convertible; Output Power Capacity 5400 Watts/6000 VA, Max Configurable Power 5400Watts/6000VA, Nominal Output Voltage 230V, Output Voltage Note Configurable for 220 : 230 or 240 nominal output voltage, Efficiency at Full Load 94.00%, Output Voltage Distortion Less than 3%,Output Frequency (sync to mains) 50/60 Hz +/- 3 Hz,Crest Factor 03:01,Waveform Type Sine Wave, Output Connections (1)*Hard Wire 3-wire (8)*(H N + G) IEC 320 C13(8),Bypass Built-in Bypass, Output Short Circuit Protection Yes,Parallel Redundancy (Option) 1 + 1, Nominal Input Voltage 230V,Input Power Factor>0.98,Input Frequency 40-70Hz,Input Connections Terminal Block, Protection Thermal Circuit Breaker (250VAC/20A), Input voltage range for main operations full load 160 - 285V, Input voltage range for mains operation half load 160-285V, High Voltage withstand Capability 420 VAC, Green Mode Range 210-250 VAC (230 V), Battery Type Mintenance - free sealed Lead-Acid battery with suspended, electrolyte. 12V 65 Ah SMF battery for 60 Min Battery Back up.

SITC of 2MP IR Indoor Dome Fixed Camera- 1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps, 2.8 mm Fixed lens, Color: 0.01 Lux at F1.2, ICR, ONVIF, support H.265, H.264, MJPEG, DWDR, 3D Digital Noise Reduction, Tripple individually configurable stream, 12 VDC & PoE, IR range: 40m, IP67, IK10, Edge Anlalytics- Line crossing detection, intrusion detection, Motion detection, video tampering, UL, CE, FCC certified. (DS-2CD3121G0-I (2.8 mm) (Approved Makes: Hikvision/ Honeywell/ Bosch)

SITC of 2MP IR Bullet Fixed Camera -1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps, 2.8 mm Fixed lens, 0.01 Lux at F1.2, 0 Lux with IR, ICR, ONVIF (PROFILE S), support H.265, H.264, MJPEG, DWDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, IP67, Edge Anlalytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Video tampering, UL, CE, FCC certified. (DS-2CD3021G0-I (2.8 mm) (Approved Makes: Hikvision/ Honeywell/ Bosch)

SITC of 64 ch Network Video Recorder - Connect Up to 64 IP Cameras, Dual OS, Up to 12 Megapixels Resolution, Two independent HDMI outputs, one HDMI output of 4K resolution,1 VGA output with output upto 1920 × 1080, Support H.265, MJPEG, Supports N+1 hot spare system,Supports RAID0, RAID1, RAID5, RAID6 and RAID10 ,Supports HDD hot swap, Supports Dual Power-Redundant, Incoming Bandwidth 320 Mbps, 8 SATA Hard Disks, ANR Technology, 8 SATA interfaces for 8 HDDs and capacity of each HDD upto 6TB, 3 × USB at least 1 × USB with 3.0, Alarm I/O 16/4, RS-485, RS-232, 2 RJ-45 10 /100/1000 Mbps self-adaptive Ethernet interface, Multiple network monitoring: Web viewer, CE, FCC, UL certified. (DS-7764NI-I8) (Approved Makes: Hikvision/ Honeywell/ Bosch)

SITC of 16 port Unmanaged Network PoE Switch: 24 port PoE Switch with PoE standard of IEEE 802.3af , IEEE 802.3at, PoE port, Uplink ports (DS-3E0326P-E) (Approved Makes: Hikvision/ Honeywell/ Bosch)

Category 6, UTP 24-Port Patch Panel Size - 482.6mm x 44.2 (19’’ x 1U), Panel Material - Steel-fully powder coated, Unshielded - RJ 45, Plug Insertion Cycle - 750 times DC Resistance- 72Ω max, Voltage Rating - 72 Vdc max, Current Rating - 1.5A max

Category 6 UTP Patch Cords - 1 Mtr Standard Colour - Blue, Grey, Yellow, RJ45 Plug - Polycarbonate plug, Current Rating - 1.5A max, Insulation Resistance - 500MΩ/km(min)@500 Vdc, Contact Resistance - 15 mΩ (max) per contact

Hard disk 6 TB

19 U Network Rack (Brand - Valrack / Netrack / Legrand)

CAT 6 Cable for CCTV camera (Brand - Digilink / Legrand / Molex)

Cable laying with PVC conduit ISO Certified

CCTV installaiton configuration & testing

32" Full HD LED Display for CCTV

Providing and fixing M.S. pipe to I.S. 1239 (Heavy class) complete with all supports & fittings like, unions, couplings, bends, elbows, tees, offsets,reducers, flanges as per table 'E' etc. to complete the work as per the requirement at site including painting with one coat of primer after surface preparartion and two coats of synthetic enamel paint, cutting and making good the walls good complete. Pipe upto 40 mm dia threaded joints with holdtite, 50 mm dia and above should be welded joint ( all type) (internal works/External Works).

Meter

Meter

Meter

Meter

Meter

Providing and fixing cast iron dual plate wafer type non return valves of PN1.6 including nuts, bolts,1.5mm thick compressed asbestos gasket including matching flanges as per table "E" complete

Providing and fixing C.I. butterfly valves PN 1.6 complete with bolts, nuts 1.5mm thick compressed asbestos gasket companion flanges as per table "E" complete.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as

Providing and fixing first aid fire hose reel drum wall mounting, swinging type(Powder coated finish in fire red) fitted with 20 mm dia. 30 m long high pressure hose(IS:444, Type-2) with 5 mm outlet SS nozzle with shut off valve (IS:8090). complete hose reel drum shall be conforming to IS:884) 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle.Drum and brackets for fixing the equipmets on wall.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Gunmetal

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

Gunmetal

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :

3 way - 150 mm dia M.S. Pipe

Providing and fixing of self illuminated / auto glow "EXIT" signs printed on photoluminescent sheet containing self illuminated base chemical, of appropriate size not less than 400 x 150 mm, suspended from ceiling or fixed to the walls with accessories as required and as directed at site.

a)Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS1520. (b) Suitable HP Squirrel cage induction motor, TEFC ,synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation,conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads.

INCOMING : Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required :

a) Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump)

a) Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Drive Pump)Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.

32 bit microprocessor based Intelligent Addressable Fire Alarm Control panel with 2 loops with battery back up. The panel would be modular, decentralized, with The panel shall be consisting with minimum 240 character LCD display and for networking. The Panel would be able to record atleast 60,000 events history. Each loop would be capable to have atleast 250 addressable detectors and addressable devices with up to 3.5km loop length. Make: Schrack Seconet (Vds approved)

1 KVA LINE INTERACTIVE UPS WITH 30 MIN BATTERY BACK UP

Supplying and fixing Intelligent Addressable type multicriteria detector with base for use as heat or smoke or combined both with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd.

Supplying and fixing Intelligent Addressable type Heat detector with base with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd.

Sypplying and fixing Intelligent Addressable Manual Call Point having inbuilt short circuit isolator i/c testing and commissiong etc as reqd.

Addressable sounder with interface module, power supply for sonder and programmable by software having integrated short circuit isolator & having operating temperature -10⁰C to + 55⁰C

Analogue Addressable Control module with IP66 casing containing four relay outputs, Each containing a potential-free DPDT contact with a fail-safe and in-built short circuit isolator The ambient temperature range shall be -20C to +60C.

Duel LED Response Indicator (LOCAL)

4"/4" JB for mounting of detectors & other accessories with necessary fittings

Supplying and fixing Outdoor Electronic Sounder with 4 distinct tone including 40W Speaker with required accessories as reqd.

Supplying and laying of 2x1.5 sq.mm. ISI marked copper armourd conductor cable with gland scoket and other wiring accessories on the existing surface/tray/shaft etc as reqd

SITC of 50 LPH RO Water Purifier alng with RO-AUTO MAX 50 lph, hdrophenumatic tank-10 LPH, Faucet-1 nozzle, accessories- clip, inlet & outlet pipe etc.

Supply,installation,factory testing and commissioning, engineering of silent Diesel Engine driven generating set 415 volts, 3 phase 4 wire,RPM 1500 engine as per IS:10001/ 10002 and Alternator as per IS: 13364 complete with isolator panel, relay panel, AMF Panel and switch gears for automatic starting on main failure, control panel having meter and sound proof canopy,Exhaust System for DG as per CPCB norms etc. of capacity, complete in all respect as following.

Supply, installation, testing and commissioning of 500 kVA, Fully Copper 11kV/433V, 3 phase, 50 Hz, Delta star, DYn11, Dry type, cast resin, indoor, natually cooled, copper double wound transformer with Off load tap changer from +5% to -10% in steps of ±2.5%, class F insulation, complete with WTI and scanner for alarm & trip, unidirectional rollers, cable end box for termination of HT cables & Bus duct for LT side complete with rating and technical name plate, earthing terminals with lugs, lifting lugs in all respect with all necessary standard accessories and as per IS. The transformer shall have suitable enclosure for providing neutral CT on earthed star point with connector for connection to REF relay provided in Main panel. All routing test as per IS shall be conducted on the transformer. The Transformer Enclosure shall have suitably designed Louvers for Air Circulation & efficient Cooling. The enclosure shall be Epoxy Powder coated. The transformer shall be subjected to all routine tests as per IS/IEC standards. Type test certificate shall be submitted. The transformer shall meet latest ECBC requirments.Make-Servokon / Schnneider/ Siemens/Powerstar/Infra Power/C&S etc of Higher grade.(Electrical Inspector Charges included)

11 KV DOUBLE POLE STRUCTURE:- Supply, erection, testing and commissioning of 2 pole structure for providing 1 No. 11KV,400A GOS in accordance with IE rules, & local authority specification and drawings and comprising of the following items below.

Supply of Conductor of 25 x 3 mm strip flat of material Cu used in air termination and down conductor system. used in air termination and down conductor system . Cross sectional area of conductor should be 50 mm². Test Parameter: a.Lightning impulse current of 100kA for 10/350 µs b.Electrical resistivity - 0.036 µΩm, Tensile strength - 120 to 240 MPa or N/mm², Salt spray - No Sign of Corrosion.Tested as per IEC 62561-2.

Supply of UV resistance Porcelein wall insulator for holding 25 x 3 mm copper strip flat Conductor .

Supply of Gunmetal Cross Connector for 25 x 3 mm dia copper strip flat. Test Parameter:Salt Spray Test ( IEC 62561-1) - No sign of Corrosion

Supply of air termination rod of 1.5 meter length of material Cu bonded of diameter 16 mm. Crown of rod should be pure copper with 5 spikes. The rod shall be mounted with clamp and fixing accessories. Test Parameter: Mechanical Load Test for individual aluminium alloy rods - 120 to 280 N/mm² Salt Spray Test-No sign of corrosion Tested as per IEC 62561-1&2

Supply of Lightning counter - LCD screen shows the number of lightning strikes, hour and date of lightning events Buttons enable TIME/DATE setting and log viewing. Replaceable battery, working life minimum five years, Complies with IEC/EN 62561-6.

Supply of upply of Metal Box Test Joint Point with enclosure between 25 x 3 mm Cu Strip Flat. Test Parameter: Salt Spray Test for test joint plate -No sign of Corrosion .Tested as per IEC 62561-1

Supply of UL Listed Maintenance Free Copper bonded Earth rod of 3048mm length having the dia of 14.2 mm with copper coating thickness of 254 microns. The rod has been tested for Dimension, Marking, Tensile Strength, Salt mist, coating thickness,Electrical resistivity test before and after corrosion test as per IEC 62561-2 & UL 467.Supply of earth enchancing mineral compound tested for leaching and TCLP with NABL accredited Lab as per IEC 62561-7 -25 kg Supply of Earth rod Clamp made up of stainless steel terminating cable / flat conductor.Supply of Earth Chamber Inspection Pit made up of poly propylene material.

Installation of Air Terminal, Copper Strip 25 x 3 flat, Earthing System Set, etc

Providing and fixing following dia RCC pipe NP2 class(light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement: 2 fine sand) including trenching (75 cm deep) and refilling etc.as required.

Meter

Meter

3.5 core, 300 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electric cable with aluminium conductor.

Providing and fixing of signages,modular FLAT frame techology of various width and lengths to form suggested usages made of aluminium extruded sections duly anodised all signages shall be provided with 0.6-0.8mm polycarbonated protecting film over the prints of appropriate size, print shall on 0.6mm coated , YUPO make biodegradable sheet printed on HP 4500 UV flat bed printer.

3mm aluminium Composite panel,duty cut by CNC router,Letter should be of SS grade 304 Steel/corrosion ressistant/high strength hardened/plasma cut with nitrogen to give excellent surface finish for edge grinding and fabrication of letter welding all complete job as per direction of E/I. Letter Size : 15 inch FAMILY COURT CUM MEDIATION CENTRE,KISHANGANJ

Providing & Fixing of Single Piece of Fabric white colour blackout ( Pollyvinal Coloride ) Which Wraps around a Casing and Fits into the top of Window Frame , Either within or Outside of Window recess. The ROLLER BLINDS is Operated by a pull cord ( alluminium channel ) attached to the bottom of the blinds or by a side - winding chain mechanism attached to the blind casing

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering taxes, royalty all complete as per building specification and direction of E/I.

Providing and laying in position mixed design mix M-30 grade in Column do - do all complet job

Beams, plinth beams, girder, bressumers, cantilevers, Suspended floors, lintels, roofs and staircase including spiral staircase, shelves etc.

Providing M30 grade R.C.C instead of M20 grade R.C.C do - do all complet job

Brick work with fly ash bricks in cm (1:6) do - do all complet job

Extra brick work in Super Structure

Centring and Shutring in do - do all complet job

Suspended floor

Roof Beam

Column

Stair

Chajja

Reinforcement for R.C.C Work do - do all complet job

8 mm tor bar

10 mm tor bar

12 mm tor bar

16 mm tor bar

20 mm tor bar

25 mm tor bar

Providing and applying white cement based putty of average thickness 2 mm do - do all complet job

Distempering with oil bound washa ble distemper of approved brandand manufacture to give an even shade .

Applying one coat of cement primer of approved brand do - do all complet job

Finishing walls with Acrylic Smooth exterior paint do - do all complet job

Forming groove of uniform size from 12x12 mm do - do all complet job

Making khurras 45 x45 cm do - do all complet job

Providing and fixing on wall face U-PVC molded fittings do - do all complet job

Providing and fixing U-PVC Pipe clip do - do all complet job

Providing and fixing inlet mouth rain water pipe do - do all complet job

Providing and fixing M.S rivets do - do all complet job

Providing and fixing wpc frame do - do all complet job

Providing and fixing 35 mm thick factory made wpc door do - do all complet job

Providing and fixing in position collapsible steel shutter do - do all complet job

Providing and fixing Three track sliding window with fly proof S.S wire mesh do - do all complet job

Extra for providing heavy sheet float glass panes instead of ordinary float glass in glazed doors,windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Filling the gap in between aluminium frame & adjacent RCC/ Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.

Providing and fixing alluminium sliding tower bolt do - do all complet job

Providing and fixing alluminium hanging floor door stopper do - do all complet job

Providing and fixing M.S Grill do - do all complet job

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes do - do all complet job

Applying priming coat With ready mixed zinc chromate yellow primer do - do all complet job

Painting with ready mixed paint of approved brand do - do all complet job

Treatment of soil under existing floors using chemical emulsion do - do all complet job

Providing and Fixing 15 mm thick calcium silicate false ceiling tiles do - do all complet job

Providing and fixing skirting with Pre-laminated do - do all complet job

Providing wood work in frames of doors, windows do - do all complet job

Providing and fixing 12 mm thick pre-laminated particle board do - do all complet job

Providing and fixing 38 mm thick parquet (wood block) flooring do - do all complet job

Providing and fixingFly proof stainless steel grade 304 wire gauge do - do all complet job.

Providing and fixing 1 mm thick M.S sheet door do - do all complet job.

Providing and fixing cast iron box for fan clamp do - do all complet job.

Providing and laying water proofing treatment to vertical & horizontal. Surfaces of depressed portion of WC. Kitchen and the like consisting …...do - do all complite job

1:3 (1 cement: 3 coarse sand)

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3mm thick water proofingmembrane, black finishedreinforcedwithnon-wovenpolyestermatt consistingofacoatof bitumenprimer for [email protected] litre/ sqmby thesame membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity70-160cps.Over theprimercoat thelayerofmembraneshallbe laidusingButaneTorch and sealingall joints etc., andpreparing the surface complete. The vital physical and chemical parameters of the membraneshallbeasunder:Jointstrengthinlongitudinalandtransverse directionat 23°Cas650/450N/5cm. Tear strength in longitudinal and transversedirectionas300/250N.Softeningpointofmembranenot less than150°C.Coldflexibilityshallbeupto-2°Cwhentestedinaccordance withASTM,D-5147.Thelayingofmembraneshallbegotdonethrough the authorised applicator of the manufacturer of membrane

Cement concrete flooring 40 mm thick 1:2:4 do - do all complite job

Cement plaster skirting (upto 30 cm hieght) do - do all complite job

Providing and fixing white vitreous china water closet squatting pan (Indian type WC pan) with 100mm sand cast Iron P or S Trap, 10 litre low level PVC flushing cistern (of approved make) with fittings CI/MS brackets, 32 mm diameter flush pipe with fittings and clamps, over flow arrangement with specials and mosquito proof coupling of approved municipal design including painting of fittings and brackets, cutting and making good the walls and floors wherever required.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

Providing and fixing white vitreous china wash basin with C.I. / M.S. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required.

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing 600 x 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers comelete.

Providing and fixing toilet paper holder:

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gms.

Providing and fixing soil, waste and vent pipes.

Providing and fixing M.S. holder bat clamps of approved design to sand cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) including cost of cutting holes and making good the walls etc.

Providing and fixing plain bend of required degree

Providing and fixing single equal plain junction of required degree with acesses door, insersion rubber washer 3mm thick, bolts and nuts complete.

Providing and fixing terminal guard.

Providing and fixing collar

Providing lead caulked joints to sand cast iron / centrifugallly cast (spun) iron pipes and fittings of diametre:

Providing and fixing M.S stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diametre.

Providing and fixing sand cast iron trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors.

Painting sand cast iron/centrifugally cast (spun) iron soil waste vent pipes and fittings with paint of any colour such as chocolate gray or buff etc. over a coat of primer (of approved quality) for new work.

merter

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

75 mm diameter

110 mm diameter

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for therma expansion.(SW)

Coupler

Shoe plain

Providing and fixing G.I. pipe complete with G.I. fittings and clamps, including, cutting and making good the walls etc. (internal work)

15 mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40 mm dia nominal bore

Painting of exposed pipes with two or more coats of synthetic enamel paint of approved quality over a coat of red oxide zinc cromate primer including painting of legends in English with direction arrows.

15 mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40 mm dia nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

15mm nominal outer dia pipes

20mm nominal outer dia pipes

Providing and fixing brass stop cock of approved quality :

15 mm dia

20 mm dia

Making connection of G.I distribution branch with G.I main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete.

25 to 40mm nominal bore

50 to 80mm nominal bore

Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end).

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

Providing and fixing gun metal non-return valve of approved quality (screwed end).

32 mm nominal bore

Vertical

Providing and placing on terrace (at all floor levels) polythylene water storage ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing PTMT grating of approved quality and colour.

150mm nominal size square 100mm diameter of the inner hinged round grating.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy aluminium rod with L.P / H.P.H.D plastic ball.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS : 8931

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

Providing and fixing uplasticised PVC connection pipe with brass unions:

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms

Office Table with Side Unit Size-(L)2000mm X (D)1800mm X (H)755mm No Of Drawers3 No Of Shelves 5 Add Ons Interchangeable Side Runner Finish Matte Size Large Style Contemporary-is a suave . Table top thk 40mm Made with a combination of engineered wood, this gorgeous desk has contrasting panels in black for a contemporary look. Coupled with a runner and storage for your files and cabinets, the Clint is a desk meant for the discerning tycoon. With a warm walnut finish, the dual tone finish of the desk adds to its overall style and finish. With an option of regular drawers and shuttered glass storage units you can take a pick of which unit suits you the best.The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

High Back Revolving Chair- Chair Size (W)660mm X (D)500mm X (H)1265mm. Made From High-Density Foam, The Sink-In Cushions And The Cradling Backrest Provides Contouring Comfort For All-Day Seating. The Soft To Touch Premium Leatherette Upholstery Add Elegance To Its Look While Also Making It Stain & Fade Resistant. Features Such As Synchro Multi-Locking Mechanism, Pneumatic Height Adjustment, Tilt Tension Control, Etc, Let You Find Your Ergonomic Position With Ease. The Pneumatic Height Adjustment Along With The Thick Padded Headrest And Armrest Further Let You Sit In Absolute Comfort. A Strong Chrome Base Supports The Structure While The 360 Swivel And 55Mm Castors. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

CANTILEVER CHAIR - Cantiliver Chair Size-(W-480mm D-490mm I Back H-530mm, W-480mm I Height Min-460mm Max--- Back max height with cantilever - 940mm, Back min height with cantiver - 460mm. Seat & Back made up of 14mm thick boiling water proof plywood os ISI303. Back reclines at A 2-to-1 ratio to the seat. 5% post consumed recycled content & 30% total recycled content. Color-Black. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

High Back Chair Size (Back Height-670xBack Width-470)mm & (Seat Depth-485xSeat Width-475)mm with Min-Max Height (460-540)mm. Nylon base chair with push back mechanism & Fix handle. Nylon base chair with push back mechanism. Back & seat cover cushion chair uphlostered in fabric & adjustable armrest locks any position. Syncro mechenism with locking system and five star chrome base with nylon casters. Seat & Back made up of 14mm thick boiling water proof plywood os ISI303. Chair rotates a full 360 degree in either direction for ease of motion. Standard on every executive with task chair & controls rate and ease with which chair reclines to different weight and strengths of users. Quick and easy adjustment regulated height of chair relative to floor. Back reclines at A 2-to-1 ratio to the seat. 5% post consumed recycled content & 30% total recycled content. Color-Black. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

Visitor Chair- Cantiliver Chair Size (Back-H-470xW-460, Seat-D-460x470)mm & Min. Height-430mm. Multipurpose fixed cantiliver chair & armrest with pading & metal base. A 14mm thick, BWR grade plywood (IS:303) is used to make the seat and back. Deep cushioned back and seat confirm to body contours for proper aligment, posture and all day comfort. 5% post consumed recycled content & 30% total recycled content. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

Visitor Chair - Chair Size (W)595mm X (D)510mm X (H)875mm. Multi-purpose fixed chair,Metal frame,PU Padding on armrest. Cushion upholstery in leatherette with four leg metal legs with matt finish. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.. Color-Black

Steel Almirah - Almirah Size (L)915MM X (D)485MM X (H)1980MM OFFICE STOREWELL WITH 4 SHELVES GAUGE: BODY: 22 GAUGE *DOORS: 20 GAUGE. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

3 Seater Sofa - 3 Seater Sofa Size - (W)1760mm X (D)720mm X (H)845mm. Fine Finesse. The Jesse sofa is contemporary style looks like. This sofa is sleek and comfortable. The sleek frame is finished in a rich polish with split panel seating. The back and seat have medium to firm cushioning for better posture. The Leg of Solid wood in glossy finished. Frame used is treated American pine wood with termite free & borer free. Soft & comfortable cushion with high density and resilient foam. Frame used is Treated american pine wood & the wood used in sofa has been 8% moisture, this prevents the wood from wrapping and bending. all wood used is termite free and borer free. Foam of sofa comfortable cushion with high density and resilent foam. all apholstry materials used in specially designed.Color-Camel/Green.The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

2 Seater Sofa - 2 Seater Sofa Size:(L)1200mm X (D)720mm X (H)845mm. Fine Finesse. The Jesse sofa is contemporary style looks like. This sofa is sleek and comfortable. The sleek frame is finished in a rich polish with split panel seating. The back and seat have medium to firm cushioning for better posture. The Leg of Solid wood in glossy finished. Frame used is treated American pine wood with termite free & borer free. Soft & comfortable cushion with high density and resilient foam. Frame used is Treated american pine wood & the wood used in sofa has been 8% moisture, this prevents the wood from wrapping and bending. all wood used is termite free and borer free. Foam of sofa comfortable cushion with high density and resilent foam. all apholstry materials used in specially designed.Color-Camel/Green. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

Wooden Center Table - Center Table (L)1130mm X (W)630mm X (H)410mm. The centre table is made keeping your comfort in mind. The sheen on the glass table top will ensure you are the envy of many a neighbour. Inlaid onto a solid wood frame that slopes inward, the table is a gorgeous piece of furniture to highlight your living room. The turned wooden legs are sleek and sturdy providing the table with its support. The wood work below the glass provides the glass with a focal point and some support. Add volumes of style to your living room with the Hopper centre table. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

Corner Table- (Dia) 390mm X(H)460mm The sleek compact table made of solid wood has a touch of style. Perfectly crafted slim tabletop & miniature design.Base is made of exquisitely crafted three curved leg base. Stylish base of the table brings an lavish look to the table.The rich finish of table enhances the table. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

High Back Chair with revolving - Size (W)590mm X (D)505mm X (H)1280mm. Chrome plated base with gas height adjustment and central tilting with single locking machenaism. Armrest with padding. Leatherette uphlostery has the look and feel of top grain leather. Cushion wtih lumber support for all day comfort. Chrome plated loop armrest with padded upholstery for extra comfort. chair rotates a full 360 degree in either direction for ease of motion. Standard on every executive & controls rate and ease with which chair reclines to different weight and strengths of users. Quick and easy adjustment regulated height of chair relative to floor. Look out tilt function when chair is in upright position. 5% post consumed recycled content & 30% total recycled content. Color-Black.The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

Mid Back Chair- (Back Height-495xBack Width-470)mm & (Seat Depth-485xSeat Width-475)mm with Min-Max Height (410-470)mm. Nylon base chair with push back mechanism & Fix handle. Back & seat cover cushion chair uphlostered in fabric & adjustable armrest locks any position. Syncro mechenism with locking system and five star Nylon base with nylon casters. Seat & Back made up of 14mm thick boiling water proof plywood os ISI303. Chair rotates a full 360 degree in either direction for ease of motion. Standard on every executive with task chair & controls rate and ease with which chair reclines to different weight and strengths of users. Quick and easy adjustment regulated height of chair relative to floor. Back reclines at A 2-to-1 ratio to the seat. 5% post consumed recycled content & 30% total recycled content. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

3 Seater Chair - Chair Size - Length 1775mm x Depth 690mm x Height 755mm 1)Seat & back single section 2)Seat is 410 mm from ground 3)Perforated mild steel powder coated 4)Seat thickness 1.2 mm 5)Seat width 520 mm 6)Beam MILD steel with black power coating thickness 1.6mm 7) Mild steel border with chrome plating for every seat & back 8) Mild steel handles chrome plated & die pressed legs at the end of chairs 9) Gross weight of regular 3-seater will be 31 kg.The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

Stackable Café Chair : Size: (L)381mm X (D)419mm X (H)839mm Seat and back in PVC Moulded Chair with SS 202 grade frame Round Pipe. The Product Should be Certified Company BIFMA,ISO-50001,Green Guard/Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC & PEFC.

3 Seater Sofa- Sofa Size( (L)1905mm X (D)890mm X (H)870mm)mm. Arm height 620mm, Seat depth 510mm, Back Height 460mm. Frame used is treated American pine wood with termite free & borer free. Soft & comfortable cushion with high density and resilient foam. Frame used is Treated american pine wood & the wood used in sofa has been 8% moisture, this prevents the wood from wrapping and bending. all wood used is termite free and borer free. Foam of sofa comfortable cushion with high density and resilent foam. all apholstry materials used in specially designed. all plywood used in M R Garde. Color-Black/Brown.The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

2 Seater Sofa- Sofa Size (W)1410mm X (D)890mm X (H)870mm. Arm height 620mm, Seat depth 510mm, Back Height 460mm. Frame used is treated American pine wood with termite free & borer free. Soft & comfortable cushion with high density and resilient foam. Frame used is Treated american pine wood & the wood used in sofa has been 8% moisture, this prevents the wood from wrapping and bending. all wood used is termite free and borer free. Foam of sofa comfortable cushion with high density and resilent foam. all apholstry materials used in specially designed. all plywood used in M R Garde. Color-Black/Brown.The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit with modular switch , modular plate, suitable size G.l. box etc as required

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate/,switch box including connections but excluding modular plate etc. as req u ired

Wiring for light/ power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface /recessed PVC conduit as required.

2x2.5 Sq.mm +1x2.5 Sq.mm

4 X 4 sq. mm + 1 X 4 sq. mm earth wire

4 X 6 sq. mm + 1 X 6 sq. mm earth wire

4 X 10 sq. mm + 1 X 10 sq. mm earth wire

4 X 16 sq. mm + 1 X 16 sq. mm earth wire

Supplying and fixing PVC/G.I box of 200mm x 250mm x 60mm deep on surface or in recess with suitable size of phenolic laminated sheet cover in fornt including painting etc as required (Adopter box above each D.B).

Supplying and fixing suitable GI Box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 and 15/16 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc. as required. (for power plug )

Supplying and fixing suitable size G.I Box with modular plate and cover in front on surface in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc., as required. (for light plugs to be used in non residential buildings )

Supplying and fixing 12 modules GI box along with moduler base & cover plate surface or in recess including providing and fixing of 2 no 5 pin 5/6 amps socket outlet with 2 no 5/6A moduler type switch, 1 no 6 pin 15/16 amps socket outlet with 1 no 15/16A moduler type switch ,Telephone , and 6/32 amps SP connection etc. as required.

Supply & fixing 4 way(4+12) double door TP & N, sheet steel, MCB distribution board, 415 volts, on surface/ in recess, complete with tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc.as required (But without MCB / RCCB / Isolator) light DB

S/F Electronics Musical call bell suitable for D.C/A.C. single phase 230 copmplete as required.

Supplying and fixing batten/angle holder incluiding connection etc as required.

Supplying and fixing 2 pin,6 amp,celling rose on the existing junction box / PVC box incluiding connection etc as required.

S/F modular blanking plate on the existing modular plate and switch box excluding modular plate as required.

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required'

Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required.

Providing and fixing following capacity busbar chamber with 4 strips of suitable size made of copper, heavy duty,complete with all accessories including connections, earthing the body etc. as required.

Supplying and fixing wall/floor mounted cubical panel board, fabricated with 16 gauge iron sheet, suitable for panel mounted switch disconnector, including bus-bar chamber, insulator and painting etc. as required. (but without busbar copper strip)

Providing and fixing MV danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

P/F 4.00 mm dia.copper wire on surface or in recess for loop earthing along with existing surface /recess for loop earthing along with existing surface/recessed conduit /submain wiring/cable etc required.

P/F lightning conductor final, made of 25mm dia. 300mm long, copper tube having single pron on top with 85 mm dia 3 mm thick copper base palte including holes etc complete as required.

P/F copper tape 20mmx3mm thick on parapet or surface of wall for lighting conductor complete as required ( for horizontal run)

P/F copper tape 20mmx3mm thick on parapet or surface of wall for lighting conductor complete as required ( for vertical run)

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required.

Metre

Supply and installation of regular/standard model A.C. ceiling fan of 1200 mm sweep with service value (CM/MM) minimum 4.00, Air delivery minimum 270 cum/min including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated copper conductor etc as required.

Supply & Installation 400 mm dia 230 volt AC wall /cabin Fan including fixing the bracket making connection testing commissioning etc as required

Supply and fixing of following sweep/ sizes PVC/ABS square body Exhaust Fan with automatic openable louvre shutter in existing opening including making connection, testing etc as required

200 mm sweep (1300/1400 RPM)

Supplying and fixing recess/surface mounted downlighter with minimum efficacy 100 lm/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required

Supplying and fixing of following types lamp in the existing nelectrical fitting/ fixtures etc. as required

Supplying and fixing recess mounted 36 watt LED flat panel (2' X 2') with minimum efficacy 100 lm/w which privides soft light and glare free symmetrical illumination suitable for armstrong/grid ceiling and integrated electronic driver etc directly on false ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing 2'X9 watt LED batten with minimum efficacy 100 lm/w in polycarbonate housing and complete with integrated electronic driver etc directly on wall/ ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor etc. as required.

Supplying and fixing following sizes of PVC conduit along with accessories in surface /recess including cutting the wall and making good the same in case of recessed conduit as required.

SITC of water cooler capacity storage 40*80 liter body stainless steel diamention 665*485*1210 mm. Tank capacity 80 liter and cooling water supply 40 liter per houre and Ro purifiers 20 liter capacity per hour water supply with all accessoriees including. Make- kent/usha/blue star/Climatrol/Voltas/Aquaguard.

SITC AC split(1.5 ton) with stabilizer ISI standard as per specification 5 star inverter AC.

Supply, Installation, Testing and Commissioning of 2.0TR Cassette Ac 5 Star with high quality black fin corrosion resistance and Air purification which contains ioniser,deodorisation filter,dust electrification, pre- filter. Super 5 star comes with (5.2) ISEER Rating.Eco-Friendly R32 Refrigerant highly efficient with a lower global warming potentials compared to R410.

Supplying and fixing modular type 25 amps A.C. unit box with ON/OFF MCB on surface or in recess complete with connections, testing and commissioning etc as required.

Stabilizer (2/1.5 Ton) ISI Standerd As per Specification

Extra copper piping electrical wire for split AC

Extra drain pipe split AC

Stand of Outdoor Unit

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power H.T. cable with aluminium conductor for working voltage upto 11 KV as required.

Providing and fixing 25 mm x 5 mm thick GI strip on surface or in recess for connections etc. as reqd.

8 Passenger(408 Kg), (G+1) Floor Add Extra for machine room less(MRL) Rs 159300.00

Annual Maintenance Cost of Lift

First Year (Free with SITC)

SECOND YEAR LIFT COST OF 5% for Add Floor

THIRD YEAR LIFT COST OF 6%

Supplying and drawing of UTP 4 pair CAT-6 LAN cable in the existing surface/recessed steel /PVC concuitas required.

Category 6 UTP Patch Cords - 1 Mtr Standard Colour - Blue, Grey, Yellow, RJ45 Plug - Polycarbonate plug, Current Rating - 1.5A max, Insulation Resistance - 500MΩ/km(min)@500 Vdc, Contact Resistance - 15 mΩ (max) per contact

Category 6 UTP Patch Cords - 2 Mtr Standard Colour - Blue, Grey, Yellow, RJ45 Plug - Polycarbonate plug, Current Rating - 1.5A max, Insulation Resistance - 500MΩ/km(min)@500 Vdc, Contact Resistance - 15 mΩ (max) per contact

24-port GbE Smart Managed Switch with GbE Uplink Interfaces-24 Ports 10/100/1000Mbps+4 SFP;Port Standards & Functions-IEEE 802.3 10BASE-T Ethernet (twisted-pair copper),IEEE 802.3u 100BASE-TX Fast Ethernet (twisted-pair copper),IEEE 802.3ab 1000BASE-T Gigabit Ethernet (twisted- pair copper),IEEE 802.3az compliance Auto-negotiation,IEEE 802.3x Flow Control; Full/Half Duplex-Full/half duplex for 10/100 Mbps speeds,Full duplex for Gigabit speed;Media Interface Exchange Auto MDI/MDIX adjustment for all twisted-pair ports;Switching Capacity 56 Gbps; Transmission Method Store-and-forward; MAC Address Table 16,000 entries per device, Maximum 64 bytes packet forwarding rate 41.7 Mpps,Packet Buffer Memory 1.5 MB,Maximum Power Consumption 22.45 watts, Standby Power Consumption 17.84 W/240 V, Acoustics 0 dBA Heat Dissipation 76.55 Btu/hr, Operating Temperature -5 to 50 ˚C (23 to 122 °F), Storage Temperature -20 to 70 ˚C (-4 to 158 °F), Operating Humidity 0% to 95% non-condensing, Storage Humidity 0% to 95% non-condensing, Diagnostic LEDs Link/Activity/Speed (Per 10/100/1000 Mbps port), Certifications CE (LVD) BSMICCC, C-Tick. Netgear / D-link/ Cisco.

Category 6, UTP 24-Port Patch Panel Size - 482.6mm x 44.2 (19’’ x 1U), Panel Material - Steel-fully powder coated, Unshielded - RJ 45, Plug Insertion Cycle - 750 times DC Resistance- 72Ω max, Voltage Rating - 72 Vdc max, Current Rating - 1.5A max

Supply fitting fixing Rack 19" 12U fully powder coated complete etc as required with complete accessories (5 amp x 6 socket, wire manager, rack fan) VALRACK/ Netrack make.

Supplying and fixing of RJ 45 computer socket suitable for Cat 6 on module GI box along with base & cover plate in surface or in recess including making connection, soldering etc. as required.

Wireless N Access Point Interface - One 10/100Mbps RJ45 Port (Auto MDI/MDIX), Button - WPS Button, Reset Button, External Power Supply - 9VDC / 0.6A, Antenna Type - 5dBi Detachable Omni Directional Antenna, Frequency - 2.4-2.4835GHz, Wireless Standards - IEEE 802.11n, IEEE 802.11g, IEEE 802.11b, Wireless Security - SSID Enable/Disable MAC Address Filter 64/128/152-bit WEP Encryption WPA/WPA2/WPA-PSK/WPA2-PSK (AES/TKIP) Encryption Wireless Modes - AP Mode, Multi-SSID Mode, Client Mode, Repeater Mode (WDS / Universal ), Bridge Mode, TPlink/Cisco/Netgear

SITC OF EPABX WITH 152 LINE EXTENSION UP TO 20 LINE WITH 4 SLT/ 2 CONSOLE (Panasonic / Simens / Matrix) 15-Party Conference, Universal Gateway, Mobile Remote Maintenance, LAN & Ethernet Port Least Cost Routing,Auto Attendant,Ext.Music Port 04 PSTN TRK+ 02 DIGITAL PORT+ 152 Analouge Extn . (EXP TO 200 LINES) Max. TDM Ports: 240 Interface support: PRI/VOIP/GSM/E&M Trunk

Supply, installation, testing & commissioning of termination box for 50 pair EPABX system complete as required

SITC OF 20 Pair Krone telephone termination box

SITC OF 20 Pair 0.5 sqm telephone cable (RR Cable/ finolex/ Anchor) with pvc conduit 25mm dia

Supplying and drawing following pair,0.5 sqmm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface / recessed PVC conduit as required.

CCTV Network Camera Dome 4 MP (Brand - Hikvision / Bosch / Honeywell) Image Sensor - 1/3" Progressive Scan CMOS, Shutter Speed - 1/3s to 1/10,000 s, Lens - 2.7mm, 4mm, 6mm @ F2.0angle of view: 106°(2.7mm), 83°(4mm), 55.4°(6mm), Day &Night - IR cut filter with auto switch, White Balance - Automatic/Manual, Video Compression - H.264/MJPEG/H.264+, Max. Resolution - 2688×1520, Communication Interface - 1 RJ45 10M/100M Ethernet port, Base T

Display : Screen size – 42 inch or above(LG/Sony/Samsung/ Philips), Panel Technology IPS, Aspect Ratio 16:9, Native Resolution 1920 x 1080 (FHD), Brightness 350nit or Higher, Contrast ratio 1100:1 or Higher, Dynamic CR 500,000:1 or Higher, Viewing Angle (H x V) 178 X 178, Orientation Portrait & Landscape, Operation Temperature 0 ⁰C to 40 ⁰C, Safety UL, eUL , EMC FCC Class “A”, IP video input 16 Channel , 1-ch, RCA (2.0 Vp-p, 1KΩ) Two-way audio input, 100Mbps Incoming bandwidth, 80Mbps Outgoing bandwidth, 128 Remote connection, HDMI/VGA output : 1-ch, resolution : 1920 × 1080P /60Hz, 1600 × 1200 /60Hz, 1280 × 1024 /60Hz, 1280 × 720 /60Hz, 1024 × 768 /60Hz, Audio output 1-ch, RCA (Linear, 1kΩ), Live view / Playback resolution : 5MP/3MP/1080p/UXGA/720p/VGA/4CIF/DCIF/2CIF/CIF/QCIF, Capability 1 SATA interface for 1 HDD Unloaded, 1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface, 1 × USB 2.0 and 1 × USB 3.0, OEM Authorization Certification,

SITC of 8 port Unmanaged Network PoE Switch: 24 port PoE Switch with PoE standard of IEEE 802.3af , IEEE 802.3at, PoE port, Uplink ports (DS-3E0326P-E) (Approved Makes: Hikvision/ Honeywell/ Bosch)

Supplying and drawing of UTP 4 pair CAT 6 LAN cable in the existing surface/ recessed PVC conduit as required.

1 run of cable

SITC of 6TB Surveillance Hard Disk (ST6000VX0023) (Approved Makes: Hikvision/ Honeywell/ Bosch)

19" 6U Rack for Switches complete as required

Camera installation and Connectivity.

BASE PHONE CLI (PANASONIC / BEETAL) Landline Phone with Caller ID Facility Corded Phone Numerical Keypad 35 Call Logs3 Display Lines Disclaimer,Tone/Pulse Switchable Ring LED Indication Flash Pause Dynamic Change Over From Pulse Tone, 1 Year Manufacturer Warranty

Supplying and fixing Intelligent Addressable type multicriteria detector with base for use as heat or smoke or combined both with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd.

Supplying and fixing Intelligent Addressable type Heat detector with base with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd.

Sypplying and fixing Intelligent Addressable Manual Call Point having inbuilt short circuit isolator i/c testing and commissiong etc as reqd.

Addressable sounder with interface module, power supply for sonder and programmable by software having integrated short circuit isolator & having operating temperature -10⁰C to + 55⁰C

Analogue Addressable Control module with IP66 casing containing four relay outputs, each containing a potential-free DPDT contact with a fail-safe and in-built short circuit isolator The ambient temperature range shall be -20C to +60C.

Supplying and Laying of 2X1.5 Sq.mm.marked copper FRLS wire with 20mm dia.PVC conduit pipe ISI marked, Complete with all fittings viz. Tees, Bends, Junction Boxes, Clamps/ Supports etc.

Duel LED Response Indicator (LOCAL)

4"/4" JB for mounting of detectors & other accessories with necessary fittings

Supplying and fixing Outdoor Electronic Sounder with 4 distinct tone including 40W Speaker with required accessories as reqd.

Supplying of XLPE/PVC insulated Sheathed (Heavy Duty) armoured electric cable with aluminium conductor of 1.1 KV graded con. IS 1554 Part I upto date amendment etc as required of following size

95 sq. mm, 3.5 core

16 sq. mm, 4 core

ABC Powder Type (Stored Pressure) Fire Extinguisher, 4 kg. Capacity, ISI mark (IS:15683), squeeze grip valve, operating temperature (+5) degree Celcuis to (+55) dgree Celcuis for Class 3A Type of Fire Filled with MAP ABC Powder, Complete in all respect

CO2 Type Fire Extinguisher, 4.5 Kg Capacity, ISI Mark (IS:15683) squeeze grip valve, operating temperature (-30) deg Cel to (55) deg cel. For Class 13B type of Fire Fitted with 1 Mt. Hose & PVC Horn, Complete in all respect.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS:1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

25 mm dia

80 mm dia

100 mm dia

150 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

Single headed Gunmetal

Single headed Stainless steel

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required :

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Gunmetal

Stainless steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following asrequired.

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

Gunmetal

Stainless steel (Grade 304)

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.

Description of Work

Boundary

Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of al! rubbish with all leads and lifts.

Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed.

Close timbering over areas including strutting, shoring and packing, cavities (wherever required) etc. complete. (Measurement to be taken of the face area timbered):

Extra for every additional lift of 1.5m or part thereof in:

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead

Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l.

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level

1:1.5:3(1 Cement :1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

1:2:4 (1 Cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering, finishing and reinforcement-All work upto plinth level

Reinforced cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finishin and reinforcement.

Reinforced cement conrete work in beams,suspended floors, roofs having slope upto 15, landings,balconiec, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excludingthe cost of centring, shuttering, finishing and reinforement with 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size).

Add or deduct for providing richer or leaner mixes respectively at all floor levels.

Brick work with bricks of class designation 100A in foundations and plinth in :

Half brick masonry with bricks of class designation 100A in foundations and plinth in :

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level

Brick work with bricks of class designation 100A in foundations and plinth in

Providing (1:4) Brick work with fly ash bricks etc all complete jobs.

Cement mortar 1:6 (1 cement: 6 coarse sand)

Extra for Brick work in superstructure above plinth level upto floor V cum Cement mortar 1:6 (1 cement: 6 coarse sand )

Half brick masonry with bricks of class designation 100A in foundations and plinth in : Cement mortar 1:4 (1 cement: 4 coarse send). Extra for half Brick masonry in superstructure above pinth level uptofloor V level.

Centring and shuttering including strutting,propping etc. and removal of form for.

Foundations, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters. Butteresses, plinth and string courses etc.

Suspended floors, roots, landings, balcnies and access platform.

Lintels, beams, plinth bams, griders, bressumers and contilevers.

Columns,Pillars, Piers, Abutments, Posts and Struts

Stairs,(excluding landings) except spiral-staircaces

Weather shade,Chajjas, corbels etc. including edges

Lintels, beams, plinth bams, griders, bressumers and contilevers.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

Thermo-Mechanically Treated bars TMTC-500-8mm dia.

Thermo-Mechanically Treated bars TMTC-500-10mm dia.

Thermo-Mechanically Treated bars TMT Fe-500-I2mrn dia.

Thermo-Mechanically Treated bars TMT Fe-500-16 mrn dia.

Thermo-Mechanically Treated bars TMT Fe-500-20 mrn dia.

Thermo-Mechanically Treated bars TMT Fe-500-25 mrn dia.

12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of near cement

15 mm cement plaster 1:3 (1 cement: 3 coarse sand ) finished with a floating coat of neat cement on the rough side of single or half brick wall.

20 mm cement plaster (1:4) etc all complete jobs.

Extra for providing and mixing water proofing material etc all complete jobs.

15 mm cement plaster on rough side of single or half brick wall of mix.

1:4(1 cement: 4 coarse sand )

1:6 (1 cement: 6 coarse sand)

Cement plaster in course sand, 12 mm cement plaster

6 mm cement plaster to ceiling

Providing and laying vitrifed floor tiles in different sizes (thickness to be specified by the manufactruer) with water absorption's less than 0.08 % and conforming to IS : 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand ) including grouting the joint with white cement and matching pigments etc., complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles 400x400 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such as white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing 20mm thick mirror polished, machine cut for kitchen platforms, vanity counters facias and similar locatins of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement :4 coarse sand) with joints treated with white cement, mixe* with matching pigament-epoxy touch ups. including rubbing, curing etx. complete at all Ibevels.

Extra for providing edge moulding to 18 mm thick marble stone counters, Vanities etc. over item no. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in -charge.

metre

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen sink in kitchen platform, vanity counters and similar location in marble / granite/stone work including necessary holes for pillar taps etc. including rubbing and polisheg of cut edges etc. complete.

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade, 2 or more coat.

Applying one coat of cement primer of approved brand and manufacture on wall surface:

Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade

Finishing walls with Acrylic Smooth exterior paint of required shade :

Providing and laying in situ seven course water proofing treatment with APP (AtacticPolypropylene) modified Polymeric membrane over roof consisting of first coat of bitumen primer @ 0.40Kg per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 2.0mm thick of 3.00 Kg/sqm weight consisting of five layers prefabricated with centre core as 1 OOmicron HMHDPE film sandwitched on both sides with polymeric mix and the polymeric mix is protected on both side with 20micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 100 grouted with cement mortar 1:3 (1 cement: 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 ( 1 cement: 3 fine sand) and finished neat which shall be paid for separately

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal ofwooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-Charge.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished 12 mm cement plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

metre

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Coupler, 110mm

Single Tee withdoor, 110x110x110mm

Band 87.50, 110mm band

Shoe plain, 110mm shoe

Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing M.S. rivets of sizes in position.

Providing and fixing pressed steel door confirming IS code 4351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by . mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

metre

Steel work in built up tubular trusses including cutting, hoisting, fixing inapplying a priming coat of approved steel primer etc all complete jobs.

Providing and fixing 35mm thick factory mode laminated veneer lumber door shutter conforming to IS:14616 & TADS 15-2001 (part B),manufactured in factories by approved manufacturers, including black enamelled M.S.butt hinges with necessary screws as per directions of Engineer in charge and panelling with panels of:

Providing and fixing in position collapsible steel shutters with vertical channes 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T-tron 40x40x6 mm with 40 mm dia steel pulleys complete with bots.nuts locking arrangement stoppers handies including applying a priming coat of approved steel primer.

Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels)made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm)

P/F factory made door frame of PVC 48x40x1.5mm in white , grey or wooden finish

P/F factory made door shutter of PVC, 30mm thk Factory made shutters with styles, rails and panels of PVC extruded sections in white, grey or wooden finish

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :

Providing and fixing alluminium handles anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc. complete:

Providing and fixing bright finished brass 100 mm mortice latch and lock with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868)aluminium lever with necessary screws etc.completefBest make of approved quality

Providing and fixing alluminium sliding tower bolt anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with nuts and screws etc. complete:

Providing and fixing alluminium hanging floor door stopper anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc.complete:

Providing and fixing M.S. grills of requirement pattern in frames of windows etc. with M.S. flats, square or round bars etc.all complete

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.).

Applying priming coat:

Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade:

Extra for providing and mixing water prooding material in cement concrete work in the proportion recommended by the manufacturers.

Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. Clear depth and 250mm apron including cost of E/W. involved with 75mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base.the drain duly.plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l,

Making plinth protection 50mm thick of cement concrete (1:3:6) , 1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti-termites' treatrnent(including the cost of chemical emulsion

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.

Providing and fixing skirting with Pre-laminated (one side decorative and other side balancing lamination) flat pressed 3 layer or graded particle board (medium density) Grade I, Type II, IS :12823 marked, with necessary fixing arrangements and screws, including drilling necessaryholes for rawl plugs etc. and priming coat on unexposed surface complete

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), including ISI marked M.S.pressed butt hinges bright finished of required size with necessery screws, all complete as per directions of Engineer-in- Charge and panelling with panels of:

38 mm thick parquet (wood block) flooring of 1st class teak wood laid over 25 mm thick levelling layer of cement concrete 1:2:4(1cement:2 coarse sand:4 store aggregate 10 mm nominal size) to be paid separately coated with a thin layer of hot bitumen of hot bitumen (blown type) @ 2.45 kg per sqm. including fixing blocks in position After dipping in hot bitumen (blown type) up to half depth ,planed levelled smooth and finished complete .

Providing and fixing in position precast R.C.C. manhole cover and frame of required shape and approved quality.

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal\ size) as per standard design

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5 mm thick) wire of high tensile strength of 165 kg/ sq mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Providing and fixing soil, waste and vent pipes :

metre

Supplying and fixing C.I. cover without frame for manholes etc all complete job

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1:3:6(1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing of glass panes with glazing clips and special metal-sash putty of approved make complete including applying a priming coat of approved steel primer; excluding the cost of metal beading and other fitting except necessary hinges or pivots as required.

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm ngle iron and 3mm MS gusset plates at the junction and corners. all necessary fittings completejncluding applying a priming coat of approved steel primer.

Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400x200x200 mm (inside)with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.

Trenching in ordinary soil upto a depth of 60 cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge of / and manure before and after flooring trench with water (excluding cost of imported earth, sludge or manure)

Supplying and stacking of good earth at site including royalty but excluding carriage (earth measured in stacks will be reduced by 20 % for payment)

Supplying and stacking Sludge at site including royalty and

Supplying and stacking at site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment)

Rough dressing the trenched ground including breaking clods.

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.

Fine dressing of the ground

Spreading of sludge, dump manure and / or good earth in required thickness as per direction of Officer-in-charge (Cost of sludge, dump manure and / or good earth to be paid separately).

Mixing earth and sludge or manure in proportion specified or directed.

Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free form weeds and fit for moving including supplying good earth if needed.

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20 % 1 part of stacked volume of manure after reduction by 8 % ) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure sludge or extra good earth if needed to be paid for separately)

Holes 1.2 m dia. And 1.2 m deep.

Holes 60 cm dia And 60 cm deep

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8 :1 (8 parts of stacked volume of earth after reduction by 8% ) flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed, within a lead of 50 m lift upto 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Plantation of trees & Shrubs/ creeps.

Shrubs / Creeps

Providing and fixing white vitreous china water closet squatting pan (Indian type WC pan) with 100mm sand cast Iron P or S Trap, 10 litre low level PVC flushing cistern (of approved make) with fittings CI/MS brackets, 32 mm diameter flush pipe with fittings and clamps, over flow arrangement with specials and mosquito proof coupling of approved municipal design including painting of fittings and brackets, cutting and making good the walls and floors wherever required.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

Providing and fixing white vitreous china wash basin with C.I. / M.S. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required.

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Providing and fixing white vitreous china pedestal for wash basin

Providing and fixing 600 x 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers comelete.

Providing and fixing toilet paper holder:

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gms.

Providing and fixing soil, waste and vent pipes.

merter

Providing and fixing M.S. holder bat clamps of approved design to sand cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) including cost of cutting holes and making good the walls etc.

Providing and fixing plain bend of required degree.

Providing and fixing single equal plain junction of required degree with acesses door, insersion rubber washer 3mm thick, bolts and nuts complete.

Providing and fixing terminal guard.

Providing and fixing collar

Providing lead caulked joints to sand cast iron / centrifugallly cast (spun) iron pipes and fittings of diametre:

Providing and fixing M.S stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diametre.

Providing and fixing sand cast iron trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors.

Painting sand cast iron/centrifugally cast (spun) iron soil waste vent pipes and fittings with paint of any colour such as chocolate gray or buff etc. over a coat of primer (of approved quality) for new work.

merter

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

merter

merter

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for therma expansion.(SW)

Coupler

Single tee with door

Shoe plain

Providing and fixing G.I. pipe complete with G.I. fittings and clamps, including, cutting and making good the walls etc. (internal work)

15 mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40 mm dia nominal bore

Painting of exposed pipes with two or more coats of synthetic enamel paint of approved quality over a coat of red oxide zinc cromate primer including painting of legends in English with direction arrows.

15 mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40 mm dia nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

metre

metre

Providing and fixing brass stop cock of approved quality :

Making connection of G.I distribution branch with G.I main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete.

Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end).

Providing and fixing gun metal non-return valve of approved quality (screwed end).

Providing and placing on terrace (at all floor levels) polythylene water storage ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing PTMT grating of approved quality and colour.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy aluminium rod with L.P / H.P.H.D plastic ball.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS : 8931

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

Providing and fixing uplasticised PVC connection pipe with brass unions:

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms

Excavating trenches of required width for pipes, cables etc. Including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5M including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering, etc.And disposing of surplus excavated soil as directed within a lead of 50 m Hard/dense soil.

metre

Providing, laying Non pressure NP2 class (light duty) RCC Pipes with collars jointed with stiff mixture of cement mortar in the propoertion of 1:2 (1 cement : 2 fine sand) including testing and jointing etc complete.

metre

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Extra for depth for manholes

metre

metre

Boring /drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in IS : 2800 (part I), including collecting samples form different strata, preparing and submitting strata chart / bore log, including hire & running Charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-Charge, upto 90 metre depth below ground level, all type of soil.

metre

Boring / drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in IS : 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer - in-Charge, beyond 90 metre & upto 150 metre depth below ground level.

metre

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.

metre

metre

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

metre

Providing and fixing suitable size threated mild steel cap or spot welded plate to the top of bore well housing / Casting pipe, removable as per requirement, all complete for borewell of :

Providing and fixing M.S. clamp of required dia to the top of casing / housing pipe of tube well as per IS : 2800 (part I ), including necessary bots & nuts of required size complete.

Providing and fixing Ball plug / Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS : 2800 (Part I)

Gravel packing in tubewell construction in accordance with IS : 4097, including providing gravel fine / medium / coarse , in required grading & sizes as per actual requirement , all complete as per direction of Engineer - in-Charges.

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I ) and IS : 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by 'V' notch method or any approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory,i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

S/F/F 2 H.P. Cromption or any other apprioved make Motor and ISI make automatic starter mounted on a common wooden board etc. all complete job.

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc.as required

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc.as required.

Wiring for light/ power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 No 4 sq.mm. FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface /recessed PVC conduit as required.

2x2.5 Sq.mm +1x2.5 Sq.mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

4 x 10 sq.mm. +1 x 10 sq.mm. earth wire

2 X 16 sq. mm + 1 X 16 sq. mm earth wire

2 X 25 sq. mm + 1 X 25 sq. mm earth wire

Supplying and fixing PVC/G.I box of 200mm x 250mm x 60mm deep on surface or in recess with suitable size of phenolic laminated sheet cover in fornt including painting etc as required.

Supplying and fixing PVC/G.I box of 75mm x75mm x 50mm deep on surface or in recess with suitable size of phenolic laminated sheet cover in fornt including painting etc as required.

Supplying and fixing suitable GI Box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc. as required. (for power plug )

Supplying and fixing suitable size G.I Box with modular plate and cover in front on surface in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc., as required. (for light plugs to be used in non residential buildings )

Supplying and fixing modular type 2 pin telephone socke/ speaker outlet on the existing modular plate & box including making connection,excluding moduler plate etc. as required.

Supplying and drawing 2 pair 0.5 sq mm. FR PVC insulated copper conductor telephone cable through existing PVC concuit including connection, testing etc. as required.

Supplying and drawing low resistance co-axial T.V cable RJ-6 grade 0.7mm solid copper conductor PE insulated shielded with fine tinned copper braid and protected with PVC sheath in the existing PVC concuit etc. as required.

Supplying and fixing modular T.V antenna socket on the existing modular plate and metal box including making connection, etc. as required.

Supply fitting fixing of electronic musicle call bell suitable for single phase 230 volts, complete etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & box excluding moduler plate etc. as required.

Supplaying and fixing 2 pin 5a celling rose on the existing junction box/PVC box including connection etc.as required.

Supplying & fixing brass batten/angle holder including connection etc. as required.

Supply & fixing 2+ 8 way double door SP & N, sheet steel, MCB distribution board, 240 volts, on surface/ in recess, complete with tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc.as required (But without MCB / RCCB / Isolator) Lighting DB

Supply & fixing 4 way(4+12) double door TP & N, sheet steel, MCB distribution board, 415 volts, on surface/ in recess, complete with tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc.as required (But without MCB / RCCB / Isolator) Power DB

Supply and fixing following rating and capacity 4 pole MCCB in existing panel board. Including drilling hole in cubical panel, making connection etc.as required.

P/F following capacity busbar chamber with 4 strips of suitable size made of copper, heavy duty complete with all accessories including connections, earthing the body etc. as reqd.

Supply and fixing 200 A 4 Pole on load / panel moumted change over switch in existing cubical panel board making connection, earthing the body etc.as required

Supplay and fixing wall /floor mounted cubicle panel board fabricated with 16 gauge iron sheet suitable for panel mounted switch discconnector including Bus bar chamber insulator and painting etc as required.9but without bus bar copper strip)

S/F digital voltmeter three phase existing cubicle panel board including drilling holes in the panel board making connection etc.

S/F digital ammeter three phase existing cubicle panel board including drilling holes in the panel board making connection etc.

Supply and Installation of regular/standard module AC ceiling fan of 1200 mm sweep including wiring the down rod of standard length 9 upto 30 cm ) with 1.5 sq mm FR pvc insulated copper conductor etc as required.

Supply and Installation of 300 mm 230 volt AC exhaust fan in the existing opening including making good the damage connection testing commissioning etc as required.

Supplying and fixing single wall mounted 20/22 watt LED type batten fitting complete with electronic driver and LED tube etc directly on wall/ ceiling including connections with 1.5 sq.mm FR PVC insulated copper conductor and earthing the body etc. as required.

Supply and fixing Bulk Head Fitting die cast aluminium alloy body with prismatic glass cover suitable for the GLS / CFL L , directly on wall / ceilling including connection etc. as required.

Supplying and fixing indoor recess mounting 36 watt LED flat panel luminaire suitable for armstrong / grid ceiling and complete with electronic driver etc. irectly on false ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supplying and fixing single wall mounted 18/22 watt LED type batten fitting complete with electronic driver and LED tube etc directly on wall/ ceiling including connections with 1.5 sq.mm FR PVC insulated copper conductor and earthing the body etc. as required.

Supplying and fixing 40/45 watt LED type street light with die cast aluminium housing for ingress protection of IP65 and complete with all accessories etc, on pole/building including connection with FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supply and erection of 6 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 130 mm, made of 3 mm thick sheet along with base plate of size 220 X 220 X 12 mm , small door opening for junction box mounting with MCB & connector, cement concrete of 1:3:6 including excavation, refilling and suitable size foundation bolts with template and all complete job as required. (but without pole collar)

Providing chemical/mineral maintenance free earthing system comprising of copper coated earth electrode 3 metre length and 17.2 mm outer dia along with 25 kg earth conductivity enhancing back fill mineral compound for earth electrode to fill up the excavated earth and earth inspection pit etc. as required. Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc. as required. Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing etc. as required.

Providing and fixing 4.00 mm dia.copper wire on surface or in recess for loop earthing as required.

P/F 25mm x 5mm G.I. Strip on surface or in recess for connections etc as required.

P/F lightning conductor final, made of 25mm dia. 300mm long, copper tube having single pron on top with 85 mm dia 3 mm thick copper base palte including holes etc complete as required.

P/F copper tape 20mmx3mm thick on parapet or surface of wall for lighting conductor complete as required ( for horizontal run)

P/F copper tape 20mmx3mm thick on parapet or surface of wall for lighting conductor complete as required ( for vertical run)

P/F testing joint, made of 20mm x 3mm thick copper Strip.125 mm long with 4 nos of tinned brass bolts nuts chuk nuts and spring washer etc complete as required.

Providing and fixing earth bus of 50 mm x 5 mm copper strip on surface for connections etc. as required.

Supplying of XLPE/PVC insulated Sheathed (Heavy Duty) armoured electric cable with aluminium conductor of 1.1 KV graded con. IS 1554 Part I upto date amendment etc as required of following size

metre

Laying of one number PVC insulated and pvc sheathed /XLPE power cable of 1.1 kv grade of following size direct in ground including excavation sand cushioning protective covering and refiling the trench etc as required.

metre

ABC Powder Type (Stored Pressure) Fire Extinguisher, 4 kg. Capacity, ISI mark (IS:15683), squeeze grip valve, operating temperature (+5) degree Celcuis to (+55) dgree Celcuis for Class 3A Type of Fire Filled with MAP ABC Powder, Complete in all respect

CO2 Type Fire Extinguisher, 4.5 Kg Capacity, ISI Mark (IS:15683) squeeze grip valve, operating temperature (-30) deg Cel to (55) deg cel. For Class 13B type of Fire Fitted with 1 Mt. Hose & PVC Horn, Complete in all respect.

SITC of 1.5 Ton 5 Star Inverter Split AC copper coil . with Stablizer (NOTE:- Air Conditioning System and its accessories should note have Made in CHINA or Any CHINEASE accesories ) Make must be of Would Class Standard. (HITACHI/DAIKIN/TOSHIBA/MITSUBISI/O General or Eqvt )

SITC of 1.0 Ton 5 Star Inverter Split AC copper coil with Stablizer . (NOTE:- Air Conditioning System and its accessories should note have Made in CHINA or CHINEASE accesories ) Make must be Would Class Standard. (HITACHI/DAIKIN/TOSHIBA/MITSUBISI/O General or Eqvt)

Extra copper pipe

Extra Drain Pipe

Supplying, installation, testing and Commissioning of passenger Car Type Elevator (lifts) 8/544 Kg-1 MPS (for FOUR stop, G+3 One No. lift) with fan, fully automatic state of the art technologies, make from World Fame manufactures (Make:- Thyssen OTIS/ MITSUBISI/ SCHINDLER or Eqvt with all complete job .

CCTV Network Camera Dome 4 MP (Brand - Hikvision / Bosch / Honeywell) Image Sensor - 1/3" Progressive Scan CMOS, Shutter Speed - 1/3s to 1/10,000 s, Lens - 2.7mm, 4mm, 6mm @ F2.0angle of view: 106°(2.7mm), 83°(4mm), 55.4°(6mm), Day &Night - IR cut filter with auto switch, White Balance - Automatic/Manual, Video Compression - H.264/MJPEG/H.264+, Max. Resolution - 2688×1520, Communication Interface - 1 RJ45 10M/100M Ethernet port, Base T

CCTV Network Camera Bullet 4 MP (Brand - Hikvision / Bosch / Honeywell) Image Sensor - 1/3" Progressive Scan CMOS, Shutter Speed - 1/3s to 1/10,000 s, Lens - 2.7mm, 4mm, 6mm @ F2.0angle of view: 106°(2.7mm), 83°(4mm), 55.4°(6mm), Day &Night - IR cut filter with auto switch, White Balance - Automatic/Manual, Video Compression - H.264/MJPEG/H.264+, Max. Resolution - 2688×1520, Communication Interface - 1 RJ45 10M/100M Ethernet port, Base T

Network Vedio Recorder up to 32 network Camera (Brand - Hikvision / Bosch / Honeywell) Dual-OS design to ensure high reliability of system running, ANR technology to enhance the storage reliabilitywhen the network is disconnected, H.265/H.264/H.264+video formats , Connectable to the third-party network cameras, Recording at up to 8 MP resolution, Supports live view, storage, and playback of the connected camera at up to 8MP resolution ,HDMI/VGA outputs provided, HDMI Videooutput at up to 4K (3840 ×2160)resolution, 4 SATA interfaceconnectable for recording and backup, Storage space effectively saved by 50% to 70% with the use of H.264+ decoding format, Incoming bandwidth - 80 MBPS, Outgoing bandwidth - 80 MBPS, Network protocols - TCP/IP, DHCP, HIK Cloud P2P, DNS, DDNS, NTP, SADP, SMTP, NFS, iSCSI, UPnP™, HTTPS

Network Switch 24 Port PoE with 2 SFP Ports (Brand - Netgear / Aruba/ HP) Network Ports - (24) 10/100/1000Mbps autosensing + 2 Gigabit SFP uplinks, Network Protocol and Standards Compatibility - IEEE 802.3i 10BASE-T• IEEE 802.3u 100BASE-TX• IEEE 802.3ab 1000BASE-T• IEEE 802.3z 1000BASE-X• IEEE 802.3x full-duplex flow control•,Power consumption: 59.3W maximum, Administrative Switch Management - IEEE 802.1Q static VLAN (64 groups, static)• Protected ports• IEEE 802.1p Class of Service (CoS)• Port-based QoS• DSCP-based QoS• DiffServ• IEEE 802.3ad Link Aggregation (manual or LACP)• IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)• IEEE 802.1ab Link Layer Discovery Protocol (LLDP)• LLDP-MED• SNMP v1, v2c, v3• RFC 1213 MIB II• RFC 1643 Ethernet Interface MIB• RFC 1493 Bridge MIB• RMON group 1, 2, 3, 9• Auto voice VLAN• DHCP Filtering• HTTP and HTTPS• Ping and traceroute• Power saving when link down• DHCP filtering• IEEE 802.1x (MD5) with Guest VLAN• Jumbo frame support• Port-based security by locked MAC addresses• MAC and IP-based ACL• SNTP• Port mirroring support (many-to-one)• Web-based configuration• Configuration backup/restore• Password access control• Firmware upgradeable• PoE (46 Watts of power budget)

Category 6, UTP 24-Port Patch Panel Size - 482.6mm x 44.2 (19’’ x 1U), Panel Material - Steel-fully powder coated, Unshielded - RJ 45, Plug Insertion Cycle - 750 times DC Resistance- 72Ω max, Voltage Rating - 72 Vdc max, Current Rating - 1.5A max

Category 6 UTP Patch Cords - 1 Mtr Standard Colour - Blue, Grey, Yellow, RJ45 Plug - Polycarbonate plug, Current Rating - 1.5A max, Insulation Resistance - 500MΩ/km(min)@500 Vdc, Contact Resistance - 15 mΩ (max) per contact

Hard disk 6 TB

19 U Network Rack (Brand - Valrack / Netrack / Legrand)

CAT 6 Cable for CCTV camera (Brand - Digilink / Legrand / Molex)

Cable laying with PVC conduit ISO Certified

CCTV installaiton configuration & testing

32" Full HD LED Display for CCTV

25 mm dia.

meter

80 mm dia.

100mm dia

150 mm dia (IS : 1239)-Class-C

Providing & Fixing standard Fireman AXE with heavy insulated rubber handle.

Providing and fixing cast iron dual plate wafer type non return valves of PN1.6 including nuts, bolts,1.5mm thick compressed asbestos gasket including matching flanges as per table "E" complete

Providing and fixing C.I. butterfly valves PN 1.6 complete with bolts, nuts 1.5mm thick compressed asbestos gasket companion flanges as per table "E" complete.

150 mm dia with lever

100 mm dia with lever

80 mm dia. With lever

Providing and fixing dial type pressure gauge with isolation cock and copper pipe at hydrant station.

Dial diameter 100 mm calibration 0-15 kg/ sq.cm.

Providing and fixing gunmetal single acting air release valve with screwed inlet 25 mm dia..

Providing & fixing of Foot Valve in underground water tank.

Providing and fixing SS316 Single headed landing valve conforming to IS -5290 (Type-A) with 63 mm dia. single instantaneous female coupling on the outlet SS316 metal blank cap and chain, necessary companion flanges, nuts, bolts, washer and gasket complete as per specification. (ISI marked). All parts and body shall be of SS316 as per IS:5290.

Providing and fixing first aid fire hose reel drum wall mounting, swinging type(Powder coated finish in fire red) fitted with 20 mm dia. 30 m long high pressure hose(IS:444, Type-2) with 5 mm outlet SS nozzle with shut off valve (IS:8090). complete hose reel drum shall be conforming to IS:884)

Providing and fixing RRL Hose Pipe 63 mm dia. 15m long rubberized lined hose including SS316 male and female instantaneous type coupling approved by fire authority, machine wound with copper wire complete in all respects. Hose shall conform to IS 636 Type-A and coupling to IS 903 -1975 ( ISI marked)

Providing and fixing standard short size SS316 branch pipe with gunmetal nozzle 16 mm dia. outlet with standard instantaneous type 63 mm dia. coupling. (ISI marked, IS:903)

Supply, Installation, Testing & Commissioning of 100 mm dia Three - Way fire brigade inlet connection of 63 mm size instantaneously make coupling and shall be protected with plastic cap & chain etc. complete with one 100 mm dia sluice valve and 100 mm dia non-return valve ( To be connected to external ring main / wet riser / sprinkler riser ). Make : KALPEX / NEW - TECH.

Supplying and fixing of hose cabinel of sjze 900 mm x 600 mm x 500 mm of 2 mm thick MS sheet with 6mm thick glazed glass doors with necessary locking 'arrangement suitable to accommodation external hydrant with bulterfly valve 2 No's and 15mtr Long Hose pipe, 1 No. branch pipe mounted on wall OR raised brick Plateform duly Painted with post office red externally and white internally with.synthetic enamel paint complete in all respact for exlernai hydrant as required.

Supply of electric driven automatic fire Pump suitable for automatic operation consisting of the following:Horizontal end suction centrifugal pump complete with mechanical seal and including necessary arrangement for testing of pump.Squirrel cage induction motor suitable for 415 V, 50 Hz, AC supply of suitable rating for the above pump with synchronous speed of 2900 RPM T.E.F.C. type and conforming to IP:55 and flexible coupling and coupling guard with the pump.Common bed plate of fabricated mild steel channel or cast iron type.Suitable reinforced cement concrete pump foundation including cushy foot mounting, foundation bolts, washers as required.

Providing and fixing air vessel for fire pumps as per following specifications:

Providing and fixing dust and vermin proof motor control panel fabricated from 14 SWG MS sheet with stove enamelled paint and comprising of: (for Fire Booste pump).

Supply, installation, testing & commissioning of electric driven Jockey Pump suitable for automatic operation consisting of the following:Horizontally mounted centrifugal end suction pump complete with mechanical seal and including necessary arrangement for testing of pump with Squirrel cage induction motor suitable for 415 V, 50 Hz, AC supply of suitable rating for the above pump with synchronous speed of 2900 RPM T.E.F.C. type and conforming to IP:55 and flexible coupling and coupling guard with the pump.

Water coolled Diesel Engine developing suitable BHP at 1500 RPM for the Pump, common bed plate for mounting of engine and pump, RCC foundation and vibration damping arrangement by Cushy Foot and engine panel provided by engine manufacturer, connection to Engine Starting Panel as per item (4), sealed maintenance free batteries of 24 V, 88 AH. Rate shall include Exhaust pipe of required length with asbestos lagging, muffler, day oil tank of 400 lts with first charge and manual oil pump set.

XLPE/PVC insulated PVC sheathed (Heavy duty) armoured electric cable with aluminium conductor.

meter

meter

32 bit microprocessor based Intelligent Addressable Fire Alarm Control panel with 2 loops with battery back up. The panel would be modular, decentralized, with The panel shall be consisting with minimum 240 character LCD display and for networking. The Panel would be able to record atleast 60,000 events history. Each loop would be capable to have atleast 250 addressable detectors and addressable devices with up to 3.5km loop length. Make: Schrack Seconet (Vds approved)

1 KVA LINE INTERACTIVE UPS WITH 30 MIN BATTERY BACK UP

Supplying and fixing Intelligent Addressable type multicriteria detector with base for use as heat or smoke or combined both with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd.

Supplying and fixing Intelligent Addressable type Heat detector with base with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd.

Sypplying and fixing Intelligent Addressable Manual Call Point having inbuilt short circuit isolator i/c testing and commissiong etc as reqd.

Addressable sounder with interface module, power supply for sonder and programmable by software having integrated short circuit isolator & having operating temperature -10⁰C to + 55⁰C

Analogue Addressable Control module with IP66 casing containing four relay outputs, Each containing a potential-free DPDT contact with a fail-safe and in-built short circuit isolator The ambient temperature range shall be -20C to +60C.

4"/4" JB for mounting of detectors & other accessories with necessary fittings

Supplying and fixing Outdoor Electronic Sounder with 4 distinct tone including 40W Speaker with required accessories as reqd.

Supplying and laying of 2x1.5 sq.mm. ISI marked copper armourd conductor cable with gland scoket and other wiring accessories on the existing surface/tray/shaft etc as reqd

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia wire and 1.4 mm wide aperture with matching wood beading

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners.all necessary fittings completejncluding applying a priming coat of approved steel primer.

Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed protions of W.C. kitchen and the like consisting of :

Providing and laying integral cement based water proofing treatment including prepatation of surface as required for treatment of roofs, balconies , terraces etc, consisting of following operations. (a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water -proofing compound cleaning the surface before treatment, (b) Laying cement concrete using broken bricks / brick bats 25 mm to 100 mm size with 50 % of cement mortar 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 over 20 mm thick layer of cement mortar of mix 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water froofing compound conforming to IS 2545 to reuired slope and treating similary the adjoining walls upto 300 mm height including rounding of junctions, or walls ad slabs. (c) After two days of proper curing

Cement concrete flooring 1:2:4(1 cement:2 coarse:sand:4 graded stone agregate) finished with a floating coat of neat cement including cement slurry, etc. but excluding the cost of nosing of steps etc. complete

Cement plaster skirting (upto 30 cm hieght) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement

Increase

Less 16.61 % below as per agreement

Description of Work

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia wire and 1.4 mm wide aperture with matching wood beading

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners.all necessary fittings completejncluding applying a priming coat of approved steel primer.

Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed protions of W.C. kitchen and the like consisting of :

Providing and laying integral cement based water proofing treatment including prepatation of surface as required for treatment of roofs, balconies , terraces etc, consisting of following operations. (a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water -proofing compound cleaning the surface before treatment, (b) Laying cement concrete using broken bricks / brick bats 25 mm to 100 mm size with 50 % of cement mortar 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 over 20 mm thick layer of cement mortar of mix 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water froofing compound conforming to IS 2545 to reuired slope and treating similary the adjoining walls upto 300 mm height including rounding of junctions, or walls ad slabs. (c) After two days of proper curing

Cement concrete flooring 1:2:4(1 cement:2 coarse:sand:4 graded stone agregate) finished with a floating coat of neat cement including cement slurry, etc. but excluding the cost of nosing of steps etc. complete

Cement plaster skirting (upto 30 cm hieght) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement

Description of Work

Amount (Rs.)

Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of al! rubbish with all leads and lifts.

Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed.

Close timbering over areas including strutting, shoring and packing, cavities (wherever required) etc. complete. (Measurement to be taken of the face area timbered):

Extra for every additional lift of 1.5m or part thereof in:

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead

Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l.

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level

1:1.5:3(1 Cement :1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

1:2:4 (1 Cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering, finishing and reinforcement-All work upto plinth level

Reinforced cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finishin and reinforcement.

Reinforced cement conrete work in beams,suspended floors, roofs having slope upto 15, landings,balconiec, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excludingthe cost of centring, shuttering, finishing and reinforement with 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size).

Add or deduct for providing richer or leaner mixes respectively at all floor levels.

Brick work with bricks of class designation 100A in foundations and plinth in :

Half brick masonry with bricks of class designation 100A in foundations and plinth in :

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level

Brick work with bricks of class designation 100A in foundations and plinth in

Providing (1:4) Brick work with fly ash bricks etc all complete jobs.

Cement mortar 1:6 (1 cement: 6 coarse sand)

Extra for Brick work in superstructure above plinth level upto floor V cum Cement mortar 1:6 (1 cement: 6 coarse sand )

Half brick masonry with bricks of class designation 100A in foundations and plinth in : Cement mortar 1:4 (1 cement: 4 coarse send). Extra for half Brick masonry in superstructure above pinth level uptofloor V level.

Centring and shuttering including strutting,propping etc. and removal of form for.

Foundations, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters. Butteresses, plinth and string courses etc.

Suspended floors, roots, landings, balcnies and access platform.

Lintels, beams, plinth bams, griders, bressumers and contilevers.

Columns,Pillars, Piers, Abutments, Posts and Struts

Stairs,(excluding landings) except spiral-staircaces

Weather shade,Chajjas, corbels etc. including edges

Lintels, beams, plinth bams, griders, bressumers and contilevers.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

Thermo-Mechanically Treated bars TMTC-500-8mm dia.

Thermo-Mechanically Treated bars TMTC-500-10mm dia.

Thermo-Mechanically Treated bars TMT Fe-500-I2mrn dia.

Thermo-Mechanically Treated bars TMT Fe-500-16 mrn dia.

Thermo-Mechanically Treated bars TMT Fe-500-20 mrn dia.

Thermo-Mechanically Treated bars TMT Fe-500-25 mrn dia.

12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of near cement

15 mm cement plaster 1:3 (1 cement: 3 coarse sand ) finished with a floating coat of neat cement on the rough side of single or half brick wall.

20 mm cement plaster (1:4) etc all complete jobs.

Extra for providing and mixing water proofing material etc all complete jobs.

15 mm cement plaster on rough side of single or half brick wall of mix.

1:4(1 cement: 4 coarse sand )

1:6 (1 cement: 6 coarse sand)

Cement plaster in course sand, 12 mm cement plaster

6 mm cement plaster to ceiling

Providing and laying vitrifed floor tiles in different sizes (thickness to be specified by the manufactruer) with water absorption's less than 0.08 % and conforming to IS : 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand ) including grouting the joint with white cement and matching pigments etc., complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles 400x400 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such as white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing 20mm thick mirror polished, machine cut for kitchen platforms, vanity counters facias and similar locatins of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement :4 coarse sand) with joints treated with white cement, mixe* with matching pigament-epoxy touch ups. including rubbing, curing etx. complete at all Ibevels.

Extra for providing edge moulding to 18 mm thick marble stone counters, Vanities etc. over item no. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in -charge.

metre

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen sink in kitchen platform, vanity counters and similar location in marble / granite/stone work including necessary holes for pillar taps etc. including rubbing and polisheg of cut edges etc. complete.

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade, 2 or more coat.

Applying one coat of cement primer of approved brand and manufacture on wall surface:

Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade

Finishing walls with Acrylic Smooth exterior paint of required shade :

Providing and laying in situ seven course water proofing treatment with APP (AtacticPolypropylene) modified Polymeric membrane over roof consisting of first coat of bitumen primer @ 0.40Kg per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 2.0mm thick of 3.00 Kg/sqm weight consisting of five layers prefabricated with centre core as 1 OOmicron HMHDPE film sandwitched on both sides with polymeric mix and the polymeric mix is protected on both side with 20micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 100 grouted with cement mortar 1:3 (1 cement: 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 ( 1 cement: 3 fine sand) and finished neat which shall be paid for separately

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal ofwooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-Charge.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished 12 mm cement plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

metre

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Coupler, 110mm

Single Tee withdoor, 110x110x110mm

Band 87.50, 110mm band

Shoe plain, 110mm shoe

Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing M.S. rivets of sizes in position.

Providing and fixing pressed steel door confirming IS code 4351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by . mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

metre

Steel work in built up tubular trusses including cutting, hoisting, fixing inapplying a priming coat of approved steel primer etc all complete jobs.

Providing and fixing 35mm thick factory mode laminated veneer lumber door shutter conforming to IS:14616 & TADS 15-2001 (part B),manufactured in factories by approved manufacturers, including black enamelled M.S.butt hinges with necessary screws as per directions of Engineer in charge and panelling with panels of:

Providing and fixing in position collapsible steel shutters with vertical channes 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T-tron 40x40x6 mm with 40 mm dia steel pulleys complete with bots.nuts locking arrangement stoppers handies including applying a priming coat of approved steel primer.

Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels)made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm)

P/F factory made door frame of PVC 48x40x1.5mm in white , grey or wooden finish

P/F factory made door shutter of PVC, 30mm thk Factory made shutters with styles, rails and panels of PVC extruded sections in white, grey or wooden finish

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :

Providing and fixing alluminium handles anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc. complete:

Providing and fixing bright finished brass 100 mm mortice latch and lock with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868)aluminium lever with necessary screws etc.completefBest make of approved quality

Providing and fixing alluminium sliding tower bolt anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with nuts and screws etc. complete:

Providing and fixing alluminium hanging floor door stopper anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc.complete:

Providing and fixing M.S. grills of requirement pattern in frames of windows etc. with M.S. flats, square or round bars etc.all complete

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.).

Applying priming coat:

Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade:

Extra for providing and mixing water prooding material in cement concrete work in the proportion recommended by the manufacturers.

Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. Clear depth and 250mm apron including cost of E/W. involved with 75mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base.the drain duly.plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l,

Making plinth protection 50mm thick of cement concrete (1:3:6) , 1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti-termites' treatrnent(including the cost of chemical emulsion

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.

Providing and fixing skirting with Pre-laminated (one side decorative and other side balancing lamination) flat pressed 3 layer or graded particle board (medium density) Grade I, Type II, IS :12823 marked, with necessary fixing arrangements and screws, including drilling necessaryholes for rawl plugs etc. and priming coat on unexposed surface complete

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), including ISI marked M.S.pressed butt hinges bright finished of required size with necessery screws, all complete as per directions of Engineer-in- Charge and panelling with panels of:

38 mm thick parquet (wood block) flooring of 1st class teak wood laid over 25 mm thick levelling layer of cement concrete 1:2:4(1cement:2 coarse sand:4 store aggregate 10 mm nominal size) to be paid separately coated with a thin layer of hot bitumen of hot bitumen (blown type) @ 2.45 kg per sqm. including fixing blocks in position After dipping in hot bitumen (blown type) up to half depth ,planed levelled smooth and finished complete .

Providing and fixing in position precast R.C.C. manhole cover and frame of required shape and approved quality.

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal\ size) as per standard design

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5 mm thick) wire of high tensile strength of 165 kg/ sq mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Providing and fixing soil, waste and vent pipes :

metre

Supplying and fixing C.I. cover without frame for manholes etc all complete job

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1:3:6(1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing of glass panes with glazing clips and special metal-sash putty of approved make complete including applying a priming coat of approved steel primer; excluding the cost of metal beading and other fitting except necessary hinges or pivots as required.

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm ngle iron and 3mm MS gusset plates at the junction and corners. all necessary fittings completejncluding applying a priming coat of approved steel primer.

Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400x200x200 mm (inside)with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.

Trenching in ordinary soil upto a depth of 60 cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge of / and manure before and after flooring trench with water (excluding cost of imported earth, sludge or manure)

Supplying and stacking of good earth at site including royalty but excluding carriage (earth measured in stacks will be reduced by 20 % for payment)

Supplying and stacking Sludge at site including royalty and

Supplying and stacking at site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment)

Rough dressing the trenched ground including breaking clods.

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.

Fine dressing of the ground

Spreading of sludge, dump manure and / or good earth in required thickness as per direction of Officer-in-charge (Cost of sludge, dump manure and / or good earth to be paid separately).

Mixing earth and sludge or manure in proportion specified or directed.

Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free form weeds and fit for moving including supplying good earth if needed.

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20 % 1 part of stacked volume of manure after reduction by 8 % ) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure sludge or extra good earth if needed to be paid for separately)

Holes 1.2 m dia. And 1.2 m deep.

Holes 60 cm dia And 60 cm deep

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8 :1 (8 parts of stacked volume of earth after reduction by 8% ) flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed, within a lead of 50 m lift upto 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Plantation of trees & Shrubs/ creeps.

Shrubs / Creeps

Providing and fixing white vitreous china water closet squatting pan (Indian type WC pan) with 100mm sand cast Iron P or S Trap, 10 litre low level PVC flushing cistern (of approved make) with fittings CI/MS brackets, 32 mm diameter flush pipe with fittings and clamps, over flow arrangement with specials and mosquito proof coupling of approved municipal design including painting of fittings and brackets, cutting and making good the walls and floors wherever required.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

Providing and fixing white vitreous china wash basin with C.I. / M.S. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required.

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Providing and fixing white vitreous china pedestal for wash basin

Providing and fixing 600 x 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers comelete.

Providing and fixing toilet paper holder:

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gms.

Providing and fixing soil, waste and vent pipes.

merter

Providing and fixing M.S. holder bat clamps of approved design to sand cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) including cost of cutting holes and making good the walls etc.

Providing and fixing plain bend of required degree.

Providing and fixing single equal plain junction of required degree with acesses door, insersion rubber washer 3mm thick, bolts and nuts complete.

Providing and fixing terminal guard.

Providing and fixing collar

Providing lead caulked joints to sand cast iron / centrifugallly cast (spun) iron pipes and fittings of diametre:

Providing and fixing M.S stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diametre.

Providing and fixing sand cast iron trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors.

Painting sand cast iron/centrifugally cast (spun) iron soil waste vent pipes and fittings with paint of any colour such as chocolate gray or buff etc. over a coat of primer (of approved quality) for new work.

merter

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

merter

merter

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for therma expansion.(SW)

Coupler

Single tee with door

Shoe plain

Providing and fixing G.I. pipe complete with G.I. fittings and clamps, including, cutting and making good the walls etc. (internal work)

15 mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40 mm dia nominal bore

Painting of exposed pipes with two or more coats of synthetic enamel paint of approved quality over a coat of red oxide zinc cromate primer including painting of legends in English with direction arrows.

15 mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40 mm dia nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

metre

metre

Providing and fixing brass stop cock of approved quality :

Making connection of G.I distribution branch with G.I main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete.

Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end).

Providing and fixing gun metal non-return valve of approved quality (screwed end).

Providing and placing on terrace (at all floor levels) polythylene water storage ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing PTMT grating of approved quality and colour.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy aluminium rod with L.P / H.P.H.D plastic ball.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS : 8931

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

Providing and fixing uplasticised PVC connection pipe with brass unions:

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms

Excavating trenches of required width for pipes, cables etc. Including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5M including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering, etc.And disposing of surplus excavated soil as directed within a lead of 50 m Hard/dense soil.

metre

Providing, laying Non pressure NP2 class (light duty) RCC Pipes with collars jointed with stiff mixture of cement mortar in the propoertion of 1:2 (1 cement : 2 fine sand) including testing and jointing etc complete.

metre

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Extra for depth for manholes

metre

metre

Boring /drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in IS : 2800 (part I), including collecting samples form different strata, preparing and submitting strata chart / bore log, including hire & running Charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-Charge, upto 90 metre depth below ground level, all type of soil.

metre

Boring / drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in IS : 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer - in-Charge, beyond 90 metre & upto 150 metre depth below ground level.

metre

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.

metre

metre

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

metre

Providing and fixing suitable size threated mild steel cap or spot welded plate to the top of bore well housing / Casting pipe, removable as per requirement, all complete for borewell of :

Providing and fixing M.S. clamp of required dia to the top of casing / housing pipe of tube well as per IS : 2800 (part I ), including necessary bots & nuts of required size complete.

Providing and fixing Ball plug / Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS : 2800 (Part I)

Gravel packing in tubewell construction in accordance with IS : 4097, including providing gravel fine / medium / coarse , in required grading & sizes as per actual requirement , all complete as per direction of Engineer - in-Charges.

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I ) and IS : 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by 'V' notch method or any approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory,i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

S/F/F 2 H.P. Cromption or any other apprioved make Motor and ISI make automatic starter mounted on a common wooden board etc. all complete job.

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc.as required

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc.as required.

Wiring for light/ power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 No 4 sq.mm. FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface /recessed PVC conduit as required.

2x2.5 Sq.mm +1x2.5 Sq.mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

4 x 10 sq.mm. +1 x 10 sq.mm. earth wire

2 X 16 sq. mm + 1 X 16 sq. mm earth wire

2 X 25 sq. mm + 1 X 25 sq. mm earth wire

Supplying and fixing PVC/G.I box of 200mm x 250mm x 60mm deep on surface or in recess with suitable size of phenolic laminated sheet cover in fornt including painting etc as required.

Supplying and fixing PVC/G.I box of 75mm x75mm x 50mm deep on surface or in recess with suitable size of phenolic laminated sheet cover in fornt including painting etc as required.

Supplying and fixing suitable GI Box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc. as required. (for power plug )

Supplying and fixing suitable size G.I Box with modular plate and cover in front on surface in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc., as required. (for light plugs to be used in non residential buildings )

Supplying and fixing modular type 2 pin telephone socke/ speaker outlet on the existing modular plate & box including making connection,excluding moduler plate etc. as required.

Supplying and drawing 2 pair 0.5 sq mm. FR PVC insulated copper conductor telephone cable through existing PVC concuit including connection, testing etc. as required.

Supplying and drawing low resistance co-axial T.V cable RJ-6 grade 0.7mm solid copper conductor PE insulated shielded with fine tinned copper braid and protected with PVC sheath in the existing PVC concuit etc. as required.

Supplying and fixing modular T.V antenna socket on the existing modular plate and metal box including making connection, etc. as required.

Supply fitting fixing of electronic musicle call bell suitable for single phase 230 volts, complete etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & box excluding moduler plate etc. as required.

Supplaying and fixing 2 pin 5a celling rose on the existing junction box/PVC box including connection etc.as required.

Supplying & fixing brass batten/angle holder including connection etc. as required.

Supply & fixing 2+ 8 way double door SP & N, sheet steel, MCB distribution board, 240 volts, on surface/ in recess, complete with tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc.as required (But without MCB / RCCB / Isolator) Lighting DB

Supply & fixing 4 way(4+12) double door TP & N, sheet steel, MCB distribution board, 415 volts, on surface/ in recess, complete with tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc.as required (But without MCB / RCCB / Isolator) Power DB

Supply and fixing following rating and capacity 4 pole MCCB in existing panel board. Including drilling hole in cubical panel, making connection etc.as required.

P/F following capacity busbar chamber with 4 strips of suitable size made of copper, heavy duty complete with all accessories including connections, earthing the body etc. as reqd.

Supply and fixing 200 A 4 Pole on load / panel moumted change over switch in existing cubical panel board making connection, earthing the body etc.as required

Supplay and fixing wall /floor mounted cubicle panel board fabricated with 16 gauge iron sheet suitable for panel mounted switch discconnector including Bus bar chamber insulator and painting etc as required.9but without bus bar copper strip)

S/F digital voltmeter three phase existing cubicle panel board including drilling holes in the panel board making connection etc.

S/F digital ammeter three phase existing cubicle panel board including drilling holes in the panel board making connection etc.

Supply and Installation of regular/standard module AC ceiling fan of 1200 mm sweep including wiring the down rod of standard length 9 upto 30 cm ) with 1.5 sq mm FR pvc insulated copper conductor etc as required.

Supply and Installation of 300 mm 230 volt AC exhaust fan in the existing opening including making good the damage connection testing commissioning etc as required.

Supplying and fixing single wall mounted 20/22 watt LED type batten fitting complete with electronic driver and LED tube etc directly on wall/ ceiling including connections with 1.5 sq.mm FR PVC insulated copper conductor and earthing the body etc. as required.

Supply and fixing Bulk Head Fitting die cast aluminium alloy body with prismatic glass cover suitable for the GLS / CFL L , directly on wall / ceilling including connection etc. as required.

Supplying and fixing indoor recess mounting 36 watt LED flat panel luminaire suitable for armstrong / grid ceiling and complete with electronic driver etc. irectly on false ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supplying and fixing single wall mounted 18/22 watt LED type batten fitting complete with electronic driver and LED tube etc directly on wall/ ceiling including connections with 1.5 sq.mm FR PVC insulated copper conductor and earthing the body etc. as required.

Supplying and fixing 40/45 watt LED type street light with die cast aluminium housing for ingress protection of IP65 and complete with all accessories etc, on pole/building including connection with FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supply and erection of 6 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 130 mm, made of 3 mm thick sheet along with base plate of size 220 X 220 X 12 mm , small door opening for junction box mounting with MCB & connector, cement concrete of 1:3:6 including excavation, refilling and suitable size foundation bolts with template and all complete job as required. (but without pole collar)

Providing chemical/mineral maintenance free earthing system comprising of copper coated earth electrode 3 metre length and 17.2 mm outer dia along with 25 kg earth conductivity enhancing back fill mineral compound for earth electrode to fill up the excavated earth and earth inspection pit etc. as required. Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc. as required. Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing etc. as required.

Providing and fixing 4.00 mm dia.copper wire on surface or in recess for loop earthing as required.

P/F 25mm x 5mm G.I. Strip on surface or in recess for connections etc as required.

P/F lightning conductor final, made of 25mm dia. 300mm long, copper tube having single pron on top with 85 mm dia 3 mm thick copper base palte including holes etc complete as required.

P/F copper tape 20mmx3mm thick on parapet or surface of wall for lighting conductor complete as required ( for horizontal run)

P/F copper tape 20mmx3mm thick on parapet or surface of wall for lighting conductor complete as required ( for vertical run)

P/F testing joint, made of 20mm x 3mm thick copper Strip.125 mm long with 4 nos of tinned brass bolts nuts chuk nuts and spring washer etc complete as required.

Providing and fixing earth bus of 50 mm x 5 mm copper strip on surface for connections etc. as required.

Supplying of XLPE/PVC insulated Sheathed (Heavy Duty) armoured electric cable with aluminium conductor of 1.1 KV graded con. IS 1554 Part I upto date amendment etc as required of following size

metre

Laying of one number PVC insulated and pvc sheathed /XLPE power cable of 1.1 kv grade of following size direct in ground including excavation sand cushioning protective covering and refiling the trench etc as required.

metre

ABC Powder Type (Stored Pressure) Fire Extinguisher, 4 kg. Capacity, ISI mark (IS:15683), squeeze grip valve, operating temperature (+5) degree Celcuis to (+55) dgree Celcuis for Class 3A Type of Fire Filled with MAP ABC Powder, Complete in all respect

CO2 Type Fire Extinguisher, 4.5 Kg Capacity, ISI Mark (IS:15683) squeeze grip valve, operating temperature (-30) deg Cel to (55) deg cel. For Class 13B type of Fire Fitted with 1 Mt. Hose & PVC Horn, Complete in all respect.

SITC of 1.5 Ton 5 Star Inverter Split AC copper coil . with Stablizer (NOTE:- Air Conditioning System and its accessories should note have Made in CHINA or Any CHINEASE accesories ) Make must be of Would Class Standard. (HITACHI/DAIKIN/TOSHIBA/MITSUBISI/O General or Eqvt )

SITC of 1.0 Ton 5 Star Inverter Split AC copper coil with Stablizer . (NOTE:- Air Conditioning System and its accessories should note have Made in CHINA or CHINEASE accesories ) Make must be Would Class Standard. (HITACHI/DAIKIN/TOSHIBA/MITSUBISI/O General or Eqvt)

Extra copper pipe

Extra Drain Pipe

Supplying, installation, testing and Commissioning of passenger Car Type Elevator (lifts) 8/544 Kg-1 MPS (for FOUR stop, G+3 One No. lift) with fan, fully automatic state of the art technologies, make from World Fame manufactures (Make:- Thyssen OTIS/ MITSUBISI/ SCHINDLER or Eqvt with all complete job .

CCTV Network Camera Dome 4 MP (Brand - Hikvision / Bosch / Honeywell) Image Sensor - 1/3" Progressive Scan CMOS, Shutter Speed - 1/3s to 1/10,000 s, Lens - 2.7mm, 4mm, 6mm @ F2.0angle of view: 106°(2.7mm), 83°(4mm), 55.4°(6mm), Day &Night - IR cut filter with auto switch, White Balance - Automatic/Manual, Video Compression - H.264/MJPEG/H.264+, Max. Resolution - 2688×1520, Communication Interface - 1 RJ45 10M/100M Ethernet port, Base T

CCTV Network Camera Bullet 4 MP (Brand - Hikvision / Bosch / Honeywell) Image Sensor - 1/3" Progressive Scan CMOS, Shutter Speed - 1/3s to 1/10,000 s, Lens - 2.7mm, 4mm, 6mm @ F2.0angle of view: 106°(2.7mm), 83°(4mm), 55.4°(6mm), Day &Night - IR cut filter with auto switch, White Balance - Automatic/Manual, Video Compression - H.264/MJPEG/H.264+, Max. Resolution - 2688×1520, Communication Interface - 1 RJ45 10M/100M Ethernet port, Base T

Network Vedio Recorder up to 32 network Camera (Brand - Hikvision / Bosch / Honeywell) Dual-OS design to ensure high reliability of system running, ANR technology to enhance the storage reliabilitywhen the network is disconnected, H.265/H.264/H.264+video formats , Connectable to the third-party network cameras, Recording at up to 8 MP resolution, Supports live view, storage, and playback of the connected camera at up to 8MP resolution ,HDMI/VGA outputs provided, HDMI Videooutput at up to 4K (3840 ×2160)resolution, 4 SATA interfaceconnectable for recording and backup, Storage space effectively saved by 50% to 70% with the use of H.264+ decoding format, Incoming bandwidth - 80 MBPS, Outgoing bandwidth - 80 MBPS, Network protocols - TCP/IP, DHCP, HIK Cloud P2P, DNS, DDNS, NTP, SADP, SMTP, NFS, iSCSI, UPnP™, HTTPS

Network Switch 24 Port PoE with 2 SFP Ports (Brand - Netgear / Aruba/ HP) Network Ports - (24) 10/100/1000Mbps autosensing + 2 Gigabit SFP uplinks, Network Protocol and Standards Compatibility - IEEE 802.3i 10BASE-T• IEEE 802.3u 100BASE-TX• IEEE 802.3ab 1000BASE-T• IEEE 802.3z 1000BASE-X• IEEE 802.3x full-duplex flow control•,Power consumption: 59.3W maximum, Administrative Switch Management - IEEE 802.1Q static VLAN (64 groups, static)• Protected ports• IEEE 802.1p Class of Service (CoS)• Port-based QoS• DSCP-based QoS• DiffServ• IEEE 802.3ad Link Aggregation (manual or LACP)• IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)• IEEE 802.1ab Link Layer Discovery Protocol (LLDP)• LLDP-MED• SNMP v1, v2c, v3• RFC 1213 MIB II• RFC 1643 Ethernet Interface MIB• RFC 1493 Bridge MIB• RMON group 1, 2, 3, 9• Auto voice VLAN• DHCP Filtering• HTTP and HTTPS• Ping and traceroute• Power saving when link down• DHCP filtering• IEEE 802.1x (MD5) with Guest VLAN• Jumbo frame support• Port-based security by locked MAC addresses• MAC and IP-based ACL• SNTP• Port mirroring support (many-to-one)• Web-based configuration• Configuration backup/restore• Password access control• Firmware upgradeable• PoE (46 Watts of power budget)

Category 6, UTP 24-Port Patch Panel Size - 482.6mm x 44.2 (19’’ x 1U), Panel Material - Steel-fully powder coated, Unshielded - RJ 45, Plug Insertion Cycle - 750 times DC Resistance- 72Ω max, Voltage Rating - 72 Vdc max, Current Rating - 1.5A max

Category 6 UTP Patch Cords - 1 Mtr Standard Colour - Blue, Grey, Yellow, RJ45 Plug - Polycarbonate plug, Current Rating - 1.5A max, Insulation Resistance - 500MΩ/km(min)@500 Vdc, Contact Resistance - 15 mΩ (max) per contact

Hard disk 6 TB

19 U Network Rack (Brand - Valrack / Netrack / Legrand)

CAT 6 Cable for CCTV camera (Brand - Digilink / Legrand / Molex)

Cable laying with PVC conduit ISO Certified

CCTV installaiton configuration & testing

32" Full HD LED Display for CCTV

25 mm dia.

meter

80 mm dia.

100mm dia

150 mm dia (IS : 1239)-Class-C

Providing & Fixing standard Fireman AXE with heavy insulated rubber handle.

Providing and fixing cast iron dual plate wafer type non return valves of PN1.6 including nuts, bolts,1.5mm thick compressed asbestos gasket including matching flanges as per table "E" complete

Providing and fixing C.I. butterfly valves PN 1.6 complete with bolts, nuts 1.5mm thick compressed asbestos gasket companion flanges as per table "E" complete.

150 mm dia with lever

100 mm dia with lever

80 mm dia. With lever

Providing and fixing dial type pressure gauge with isolation cock and copper pipe at hydrant station.

Dial diameter 100 mm calibration 0-15 kg/ sq.cm.

Providing and fixing gunmetal single acting air release valve with screwed inlet 25 mm dia..

Providing & fixing of Foot Valve in underground water tank.

Providing and fixing SS316 Single headed landing valve conforming to IS -5290 (Type-A) with 63 mm dia. single instantaneous female coupling on the outlet SS316 metal blank cap and chain, necessary companion flanges, nuts, bolts, washer and gasket complete as per specification. (ISI marked). All parts and body shall be of SS316 as per IS:5290.

Providing and fixing first aid fire hose reel drum wall mounting, swinging type(Powder coated finish in fire red) fitted with 20 mm dia. 30 m long high pressure hose(IS:444, Type-2) with 5 mm outlet SS nozzle with shut off valve (IS:8090). complete hose reel drum shall be conforming to IS:884)

Providing and fixing RRL Hose Pipe 63 mm dia. 15m long rubberized lined hose including SS316 male and female instantaneous type coupling approved by fire authority, machine wound with copper wire complete in all respects. Hose shall conform to IS 636 Type-A and coupling to IS 903 -1975 ( ISI marked)

Providing and fixing standard short size SS316 branch pipe with gunmetal nozzle 16 mm dia. outlet with standard instantaneous type 63 mm dia. coupling. (ISI marked, IS:903)

Supply, Installation, Testing & Commissioning of 100 mm dia Three - Way fire brigade inlet connection of 63 mm size instantaneously make coupling and shall be protected with plastic cap & chain etc. complete with one 100 mm dia sluice valve and 100 mm dia non-return valve ( To be connected to external ring main / wet riser / sprinkler riser ). Make : KALPEX / NEW - TECH.

Supplying and fixing of hose cabinel of sjze 900 mm x 600 mm x 500 mm of 2 mm thick MS sheet with 6mm thick glazed glass doors with necessary locking 'arrangement suitable to accommodation external hydrant with bulterfly valve 2 No's and 15mtr Long Hose pipe, 1 No. branch pipe mounted on wall OR raised brick Plateform duly Painted with post office red externally and white internally with.synthetic enamel paint complete in all respact for exlernai hydrant as required.

Supply of electric driven automatic fire Pump suitable for automatic operation consisting of the following:Horizontal end suction centrifugal pump complete with mechanical seal and including necessary arrangement for testing of pump.Squirrel cage induction motor suitable for 415 V, 50 Hz, AC supply of suitable rating for the above pump with synchronous speed of 2900 RPM T.E.F.C. type and conforming to IP:55 and flexible coupling and coupling guard with the pump.Common bed plate of fabricated mild steel channel or cast iron type.Suitable reinforced cement concrete pump foundation including cushy foot mounting, foundation bolts, washers as required.

Providing and fixing air vessel for fire pumps as per following specifications:

Providing and fixing dust and vermin proof motor control panel fabricated from 14 SWG MS sheet with stove enamelled paint and comprising of: (for Fire Booste pump).

Supply, installation, testing & commissioning of electric driven Jockey Pump suitable for automatic operation consisting of the following:Horizontally mounted centrifugal end suction pump complete with mechanical seal and including necessary arrangement for testing of pump with Squirrel cage induction motor suitable for 415 V, 50 Hz, AC supply of suitable rating for the above pump with synchronous speed of 2900 RPM T.E.F.C. type and conforming to IP:55 and flexible coupling and coupling guard with the pump.

Water coolled Diesel Engine developing suitable BHP at 1500 RPM for the Pump, common bed plate for mounting of engine and pump, RCC foundation and vibration damping arrangement by Cushy Foot and engine panel provided by engine manufacturer, connection to Engine Starting Panel as per item (4), sealed maintenance free batteries of 24 V, 88 AH. Rate shall include Exhaust pipe of required length with asbestos lagging, muffler, day oil tank of 400 lts with first charge and manual oil pump set.

XLPE/PVC insulated PVC sheathed (Heavy duty) armoured electric cable with aluminium conductor.

meter

meter

32 bit microprocessor based Intelligent Addressable Fire Alarm Control panel with 2 loops with battery back up. The panel would be modular, decentralized, with The panel shall be consisting with minimum 240 character LCD display and for networking. The Panel would be able to record atleast 60,000 events history. Each loop would be capable to have atleast 250 addressable detectors and addressable devices with up to 3.5km loop length. Make: Schrack Seconet (Vds approved)

1 KVA LINE INTERACTIVE UPS WITH 30 MIN BATTERY BACK UP

Supplying and fixing Intelligent Addressable type multicriteria detector with base for use as heat or smoke or combined both with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd.

Supplying and fixing Intelligent Addressable type Heat detector with base with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd.

Sypplying and fixing Intelligent Addressable Manual Call Point having inbuilt short circuit isolator i/c testing and commissiong etc as reqd.

Addressable sounder with interface module, power supply for sonder and programmable by software having integrated short circuit isolator & having operating temperature -10⁰C to + 55⁰C

Analogue Addressable Control module with IP66 casing containing four relay outputs, Each containing a potential-free DPDT contact with a fail-safe and in-built short circuit isolator The ambient temperature range shall be -20C to +60C.

4"/4" JB for mounting of detectors & other accessories with necessary fittings

Supplying and fixing Outdoor Electronic Sounder with 4 distinct tone including 40W Speaker with required accessories as reqd.

Supplying and laying of 2x1.5 sq.mm. ISI marked copper armourd conductor cable with gland scoket and other wiring accessories on the existing surface/tray/shaft etc as reqd

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia wire and 1.4 mm wide aperture with matching wood beading

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners.all necessary fittings completejncluding applying a priming coat of approved steel primer.

Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed protions of W.C. kitchen and the like consisting of :

Providing and laying integral cement based water proofing treatment including prepatation of surface as required for treatment of roofs, balconies , terraces etc, consisting of following operations. (a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water -proofing compound cleaning the surface before treatment, (b) Laying cement concrete using broken bricks / brick bats 25 mm to 100 mm size with 50 % of cement mortar 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 over 20 mm thick layer of cement mortar of mix 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water froofing compound conforming to IS 2545 to reuired slope and treating similary the adjoining walls upto 300 mm height including rounding of junctions, or walls ad slabs. (c) After two days of proper curing

Cement concrete flooring 1:2:4(1 cement:2 coarse:sand:4 graded stone agregate) finished with a floating coat of neat cement including cement slurry, etc. but excluding the cost of nosing of steps etc. complete

Cement plaster skirting (upto 30 cm hieght) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement

Total asper Work Done

Less 16.61 % below as per agreement

( Increase - Decrease )

Description of Work

Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of al! rubbish with all leads and lifts.

Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed.

Extra for every additional lift of 1.5m or part thereof in:

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead

Close timbering over areas including strutting, shoring and packing, cavities (wherever required) etc. complete. (Measurement to be taken of the face area timbered):

Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l.

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level

1:2:4 (1 Cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size)

Extra for providing and mixing water prooding material in cement concrete work in the proportion recommended by the manufacturers.

Extra for providing and mixing water proofing material etc all complete jobs.

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering, finishing and reinforcement-All work upto plinth level

Reinforced cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finishin and reinforcement.

Reinforced cement conrete work in beams,suspended floors, roofs having slope upto 15, landings,balconiec, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excludingthe cost of centring, shuttering, finishing and reinforement with 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size).

Add or deduct for providing richer or leaner mixes respectively at all floor levels.

Brick work with bricks of class designation 100A in foundations and plinth in

Brick work with bricks with fly ash bricks as per IS 12894(2002) & 3495 in foundation and plinth in :

Cement mortar 1:6 (1 cement: 6 coarse sand)

Cement mortar 1:4 (1 cement: 4 coarse sand )

Extra for Brick work in superstructure above plinth level upto floor V cum Cement mortar 1:6 (1 cement: 6 coarse sand )

Half brick masonry with bricks of class designation 100A in foundations and plinth in : Cement mortar 1:4 (1 cement: 4 coarse send). Extra for half Brick masonry in superstructure above pinth level uptofloor V level.

Extra for half Brick masonry in superstructure above pinth level upto

Centring and shuttering including strutting,propping etc. and removal of form for.

Foundations, footings, bases of columns etc. for mass concrete.

Suspended floors, roots, landings, balcnies and access platform.

Lintels, beams, plinth bams, griders, bressumers and contilevers.

Columns,Pillars, Piers, Abutments, Posts and Struts

Stairs,(excluding landings) except spiral-staircaces

Weather shade,Chajjas, corbels etc. including edges

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

Thermo-Mechanically Treated bars TMTC-500-8mm dia.

Thermo-Mechanically Treated bars TMTC-500-10mm dia.

Thermo-Mechanically Treated bars TMT Fe-500-I2mrn dia.

Thermo-Mechanically Treated bars TMT Fe-500-16 mrn dia.

Thermo-Mechanically Treated bars TMT Fe-500-20 mrn dia.

Thermo-Mechanically Treated bars TMT Fe-500-25 mrn dia.

12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of near cement

15 mm cement plaster 1:3 (1 cement: 3 coarse sand ) finished with a floating coat of neat cement on the rough side of single or half brick wall.

15 mm cement plaster on rough side of single or half brick wall of mix.

1:4(1 cement: 4 coarse sand )

1:6 (1 cement: 6 coarse sand)

20 mm cement plaster (1:4) etc all complete jobs.

1:6(1 cement: 6 coarse sand)

1:4(1 cement: 4 coarse sand)

Size of Tile 60x60 cm

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles 400x400 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such as white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing 20mm thick mirror polished, machine cut for kitchen platforms, vanity counters facias and similar locatins of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement :4 coarse sand) with joints treated with white cement, mixe* with matching pigament-epoxy touch ups. including rubbing, curing etx. complete at all Ibevels.

Extra for providing edge moulding to 18 mm thick marble stone counters, Vanities etc. over item no. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in -charge.

metre

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen sink in kitchen platform, vanity counters and similar location in marble / granite/stone work including necessary holes for pillar taps etc. including rubbing and polisheg of cut edges etc. complete.

Structural steel work riveted or bolted in built up sections, trusess and framed work, including cutting,hoisting,fixing in position and applying a priming coat of approved ateef primer all complete.

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with G.I.J. or L hooks . Bolts and nuts 8 mm dia. G. 1. limpet and bitumen washers complete.

metre

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washa ble distemper of approved brand

Applying one coat of cement primer of approved brand and manufacture on wall surface:

Finishing walls with Acrylic Smooth exterior paint of required shade :

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal ofwooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-Charge.

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished 12 mm cement plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

metre

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Coupler, 110mm

Single Tee withdoor, 110x110x110mm

Band 87.50, 110mm band

Shoe plain, 110mm shoe

Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing M.S. rivets of sizes in position.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm, modulus of elasticity 900 N/mm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for Separately).

metre

Providing and fixing 35mm thick factory mode laminated veneer lumber door shutter conforming to IS:14616 & TADS 15-2001 (part B),manufactured in factories by approved manufacturers, including black enamelled M.S.butt hinges with necessary screws as per directions of Engineer in charge and panelling with panels of:

35 mm thick

Providing and fixing in position collapsible steel shutters with vertical channes 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T-tron 40x40x6 mm with 40 mm dia steel pulleys complete with bots.nuts locking arrangement stoppers handies including applying a priming coat of approved steel primer.

Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels)made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm)

Extra for providing heavy sheet float glass panes instead of ordinary float glass in glazed doors,windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia wire and 1.4 mm wide aperture with matching wood beading

P/F factory made door frame of PVC 48x40x1.5mm

P/F factory made door shutter of PVC, 30mm thk Factory made shutters with styles, rails and panels of PVC extruded sections in white, grey or wooden finish

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :

Providing and fixing alluminium handles anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc. complete:

Providing and fixing bright finished brass 100 mm mortice latch and lock with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868)aluminium lever with necessary screws etc.completefBest make of approved quality

Providing and fixing alluminium sliding door bolt anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with nuts and screws etc. complete:

Providing and fixing alluminium sliding tower bolt anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with nuts and screws etc. complete:

Providing and fixing alluminium hanging floor door stopper anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc.complete:

Providing and fixing M.S. grills of requirement pattern in frames of windows etc. with M.S. flats, square or round bars etc.all complete

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.).

Applying priming coat:

Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade:

Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. Clear depth and 250mm apron including cost of E/W. involved with 75mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base.the drain duly.plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l,

Making plinth protection 50mm thick of cement concrete (1:3:6) , 1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti-termites' treatrnent(including the cost of chemical emulsion

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.

Providing and fixing skirting with Pre-laminated (one side decorative and other side balancing lamination) flat pressed 3 layer or graded particle board (medium density) Grade I, Type II, IS :12823 marked, with necessary fixing arrangements and screws, including drilling necessaryholes for rawl plugs etc. and priming coat on unexposed surface complete

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

38 mm thick parquet (wood block) flooring of 1st class teak wood laid over 25 mm thick levelling layer of cement concrete 1:2:4(1cement:2 coarse sand:4 store aggregate 10 mm nominal size) to be paid separately coated with a thin layer of hot bitumen of hot bitumen (blown type) @ 2.45 kg per sqm. including fixing blocks in position After dipping in hot bitumen (blown type) up to half depth ,planed levelled smooth and finished complete .

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners.all necessary fittings completejncluding applying a priming coat of approved steel primer.

Providing and fixing steel glazed doors, windows and ventilatrs of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1:3:6(1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with woodenplugs and screws or raw) plugs and screws or with fixing dips or with bolts and nuts as required, including providing and fixing of glass panes with glazing dips and special metal-sash putty pf approved make complete including applying a priming coat of approved steel primer; excluding the cost of metal beading and other fitting except necessary hinges or pivots as required

Extra for providing and fixing steel beading of approved shape and section with screws instread of glaxing clips and met. Sash putty in steel doors, windows, Ventilators and comosite units.

Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete

Providing and fixing in position precast R.C.C. manhole cover and frame of required shape and approved quality.

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal\ size) as per standard design

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed protions of W.C. kitchen and the like consisting of :

Providing and laying integral cement based water proofing treatment including prepatation of surface as required for treatment of roofs, balconies , terraces etc, consisting of following operations. (a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water -proofing compound cleaning the surface before treatment, (b) Laying cement concrete using broken bricks / brick bats 25 mm to 100 mm size with 50 % of cement mortar 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 over 20 mm thick layer of cement mortar of mix 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water froofing compound conforming to IS 2545 to reuired slope and treating similary the adjoining walls upto 300 mm height including rounding of junctions, or walls ad slabs. (c) After two days of proper curing

With average thickness of 120 mm and minimum thickness at khurras point to be 65 ..

Providing and fixing soil, waste and vent pipes.

Cement concrete flooring 1:2:4(1 cement:2 coarse:sand:4 graded stone agregate) finished with a floating coat of neat cement including cement slurry, etc. but excluding the cost of nosing of steps etc. complete

Cement plaster skirting (upto 30 cm hieght) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement

Providing and fixing white vitreous china water closet squatting pan (Indian type WC pan) with 100mm sand cast Iron P or S Trap, 10 litre low level PVC flushing cistern (of approved make) with fittings CI/MS brackets, 32 mm diameter flush pipe with fittings and clamps, over flow arrangement with specials and mosquito proof coupling of approved municipal design including painting of fittings and brackets, cutting and making good the walls and floors wherever required.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

Providing and fixing white vitreous china wash basin with C.I. / M.S. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required.

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing 600 x 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers comelete.

Providing and fixing toilet paper holder:

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gms.

Providing and fixing soil, waste and vent pipes.

Providing and fixing M.S. holder bat clamps of approved design to sand cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) including cost of cutting holes and making good the walls etc.

Providing and fixing plain bend of required degree

Providing and fixing single equal plain junction of required degree with acesses door, insersion rubber washer 3mm thick, bolts and nuts complete.

Providing and fixing terminal guard.

Providing and fixing collar

Providing lead caulked joints to sand cast iron / centrifugallly cast (spun) iron pipes and fittings of diametre:

Providing and fixing M.S stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diametre.

Providing and fixing sand cast iron trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors.

Painting sand cast iron/centrifugally cast (spun) iron soil waste vent pipes and fittings with paint of any colour such as chocolate gray or buff etc. over a coat of primer (of approved quality) for new work.

merter

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Metre

Metre

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for therma expansion.(SW)

Coupler

Single tee with door

Shoe plain

Providing and fixing G.I. pipe complete with G.I. fittings and clamps, including, cutting and making good the walls etc. (internal work)

15 mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40 mm dia nominal bore

Painting of exposed pipes with two or more coats of synthetic enamel paint of approved quality over a coat of red oxide zinc cromate primer including painting of legends in English with direction arrows.

15 mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40 mm dia nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

15mm nominal outer dia pipes

20mm nominal outer dia pipes

Providing and fixing brass stop cock of approved quality :

15 mm dia

20 mm dia

Making connection of G.I distribution branch with G.I main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete.

25 to 40mm nominal bore

50 to 80mm nominal bore

Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end).

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

Providing and fixing gun metal non-return valve of approved quality (screwed end).

Providing and placing on terrace (at all floor levels) polythylene water storage ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing PTMT grating of approved quality and colour.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy aluminium rod with L.P / H.P.H.D plastic ball.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS : 8931

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

Providing and fixing uplasticised PVC connection pipe with brass unions:

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms

Excavating trenches of required width for pipes, cables etc. Including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5M including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering, etc.And disposing of surplus excavated soil as directed within a lead of 50 m Hard/dense soil.

Metre

Providing, laying Non pressure NP2 class (light duty) RCC Pipes with collars jointed with stiff mixture of cement mortar in the propoertion of 1:2 (1 cement : 2 fine sand) including testing and jointing etc complete.

Metre

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

With F.P.S. bricks (For Storm water)

With F.P.S. bricks (For Sewer)

Extra for depth for manholes

F.P.S. bricks (For Storm water)

F.P.S. bricks (For Sewer)

Boring /drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in IS : 2800 (part I), including collecting samples form different strata, preparing and submitting strata chart / bore log, including hire & running Charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-Charge, upto 90 metre depth below ground level, all type of soil.

metre

Boring / drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in IS : 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer - in-Charge, beyond 90 metre & upto 150 metre depth below ground level.

metre

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.

100mm nominal size dia

150 mm nominal size dia.

100 mm nominal size

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

metre

Gravel packing in tubewell construction in accordance with IS : 4097, including providing gravel fine / medium / coarse , in required grading & sizes as per actual requirement , all complete as per direction of Engineer - in-Charges.

Development of tube well in accordance with IS : 2800 (part I ) and IS : 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by 'V' notch method or any approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory,i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threated mild steel cap or spot welded plate to the top of bore well housing / Casting pipe, removable as per requirement, all complete for borewell of :

100 mm dia

150 mm clamp

Providing and fixing M.S. clamp of required dia to the top of casing / housing pipe of tube well as per IS : 2800 (part I ), including necessary bots & nuts of required size complete.

Providing and fixing Ball plug / Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS : 2800 (Part I)

S/F/F 2 H.P. Cromption or any other apprioved make Motor and ISI make automatic starter mounted on a common wooden board etc. all complete job.

Trenching in ordinary soil upto a depth of 60 cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge of/and manure before and after flooding trench with water (including cost of imported earth,sludge or manure).

Supplying and stacking of good earth at site including royalty but excluding carriage (earth measusred in stacks will be reduced by 20% for payment).

Supplying and stacking Sludge at site including royalty and carriage (Sludge measusred in stacks will be reduced by 8% for payment)

Supplying and stacking a' site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment). Screened through sieve of l.S. designation 4.75 mm

Rough dressing the trenched ground including breaking clods.

Uprooting weeds form the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.

Fine dressing the ground

Spreading of sludge, dump manure or/and good earth in required thickness (Cost of sludge, dump manure or/and good earth to be paid separately).

Mixing earth and sjudge or manure in porportion specified or directed.

Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more tili the grass forms a thick lawn free form weeds and fit for mowing including supplying good earth if needed. In rows 5 cm apart in either direction.

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20 % 1 part of stacked volume of manure after reduction by 8 % ) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure sludge or extra good earth if needed to be paid for separately)

Holes 1.2 m dia. And 1.2 m deep.

Holes 60 cm dia And 60 cm deep

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8 :1 (8 parts of stacked volume of earth after reduction by 8% ) flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed, within a lead of 50 m lift upto 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Plantation of trees

Shrubs / Creeps

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc.as required

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc.as required.

Wiring for light/ power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 No 4 sq.mm. FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface /recessed PVC conduit as required.

Metre

Metre

Metre

Metre

Metre

Supplying and fixing PVC/G.I box of 200mm x 250mm x 60mm deep on surface or in recess with suitable size of phenolic laminated sheet cover in fornt including painting etc as required.

Supplying and fixing PVC/G.I box of 75mm x75mm x 50mm deep on surface or in recess with suitable size of phenolic laminated sheet cover in fornt including painting etc as required.

Supplying and fixing suitable GI Box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc. as required. (for power plug )

Supplying and fixing suitable size G.I Box with modular plate and cover in front on surface in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc., as required. (for light plugs to be used in non residential buildings )

Supplying and fixing modular type 2 pin telephone socke/ speaker outlet on the existing modular plate & box including making connection,excluding moduler plate etc. as required.

Supplying and drawing 2 pair 0.5 sq mm. FR PVC insulated copper conductor telephone cable through existing PVC concuit including connection, testing etc. as required.

Supplying and drawing low resistance co-axial T.V cable RJ-6 grade 0.7mm solid copper conductor PE insulated shielded with fine tinned copper braid and protected with PVC sheath in the existing PVC concuit etc. as required.

Supplying and fixing modular T.V antenna socket on the existing modular plate and metal box including making connection, etc. as required.

Supply fitting fixing of electronic musicle call bell suitable for single phase 230 volts, complete etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & box excluding moduler plate etc. as required.

Supplaying and fixing 2 pin 5a celling rose on the existing junction box/PVC box including connection etc.as required.

Supplying & fixing brass batten/angle holder including connection etc. as required.

Supply & fixing 2+ 8 way double door SP & N, sheet steel, MCB distribution board, 240 volts, on surface/ in recess, complete with tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc.as required (But without MCB / RCCB / Isolator) Lighting DB

Supply & fixing 4 way(4+12) double door TP & N, sheet steel, MCB distribution board, 415 volts, on surface/ in recess, complete with tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc.as required (But without MCB / RCCB / Isolator) Power DB

Supply and fixing following rating and capacity 4 pole MCCB in existing panel board. Including drilling hole in cubical panel, making connection etc.as required.

P/F following capacity busbar chamber with 4 strips of suitable size made of copper, heavy duty complete with all accessories including connections, earthing the body etc. as reqd.

Supply and fixing 200 A 4 Pole on load / panel moumted change over switch in existing cubical panel board making connection, earthing the body etc.as required

Supplay and fixing wall /floor mounted cubicle panel board fabricated with 16 gauge iron sheet suitable for panel mounted switch discconnector including Bus bar chamber insulator and painting etc as required.9but without bus bar copper strip)

S/F digital voltmeter three phase existing cubicle panel board including drilling holes in the panel board making connection etc.

S/F digital ammeter three phase existing cubicle panel board including drilling holes in the panel board making connection etc.

Supply and Installation of regular/standard module AC ceiling fan of 1200 mm sweep including wiring the down rod of standard length 9 upto 30 cm ) with 1.5 sq mm FR pvc insulated copper conductor etc as required.

Supply and Installation of 300 mm 230 volt AC exhaust fan in the existing opening including making good the damage connection testing commissioning etc as required.

Supplying and fixing single wall mounted 20/22 watt LED type batten fitting complete with electronic driver and LED tube etc directly on wall/ ceiling including connections with 1.5 sq.mm FR PVC insulated copper conductor and earthing the body etc. as required.

Supply and fixing Bulk Head Fitting die cast aluminium alloy body with prismatic glass cover suitable for the GLS / CFL L , directly on wall / ceilling including connection etc. as required.

Supplying and fixing indoor recess mounting 36 watt LED flat panel luminaire suitable for armstrong / grid ceiling and complete with electronic driver etc. irectly on false ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supplying and fixing single wall mounted 18/22 watt LED type batten fitting complete with electronic driver and LED tube etc directly on wall/ ceiling including connections with 1.5 sq.mm FR PVC insulated copper conductor and earthing the body etc. as required.

Supplying and fixing 90 watt LED type street light with die cast aluminium housing for ingress protection of IP65 and complete with all accessories etc, on pole/building including connection with FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supply and erection of 6 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 130 mm, made of 3 mm thick sheet along with base plate of size 220 X 220 X 12 mm , small door opening for junction box mounting with MCB & connector, cement concrete of 1:3:6 including excavation, refilling and suitable size foundation bolts with template and all complete job as required. (but without pole collar)

Providing chemical/mineral maintenance free earthing system comprising of copper coated earth electrode 3 metre length and 17.2 mm outer dia along with 25 kg earth conductivity enhancing back fill mineral compound for earth electrode to fill up the excavated earth and earth inspection pit etc. as required. Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc. as required. Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing etc. as required.

Supplying of XLPE/PVC insulated Sheathed (Heavy Duty) armoured electric cable with aluminium conductor of 1.1 KV graded con. IS 1554 Part I upto date amendment etc as required of following size

Metre

Laying of one number PVC insulated and pvc sheathed /XLPE power cable of 1.1 kv grade of following size direct in ground including excavation sand cushioning protective covering and refiling the trench etc as required.

Metre

ABC Powder Type (Stored Pressure) Fire Extinguisher, 4 kg. Capacity, ISI mark (IS:15683), squeeze grip valve, operating temperature (+5) degree Celcuis to (+55) dgree Celcuis for Class 3A Type of Fire Filled with MAP ABC Powder, Complete in all respect

CO2 Type Fire Extinguisher, 4.5 Kg Capacity, ISI Mark (IS:15683) squeeze grip valve, operating temperature (-30) deg Cel to (55) deg cel. For Class 13B type of Fire Fitted with 1 Mt. Hose & PVC Horn, Complete in all respect.

SITC of 1.5 Ton 5 Star Inverter Split AC copper coil . with Stablizer (NOTE:- Air Conditioning System and its accessories should note have Made in CHINA or Any CHINEASE accesories ) Make must be of Would Class Standard. (HITACHI/DAIKIN/TOSHIBA/MITSUBISI/O General or Eqvt )

SITC of 1.0 Ton 5 Star Inverter Split AC copper coil with Stablizer . (NOTE:- Air Conditioning System and its accessories should note have Made in CHINA or CHINEASE accesories ) Make must be Would Class Standard. (HITACHI/DAIKIN/TOSHIBA/MITSUBISI/O General or Eqvt)

SITC of 2 Ton inverter Cassette AC 5 star with all accessories & all comlete work.( Make- blue star/mitsubishi/lg/carrier/Hitachi)

Extra copper pipe

Extra Drain Pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.

Meter

Supplying, installation, testing and Commissioning of passenger Car Type Elevator (lifts) 8/544 Kg-1 MPS (for FOUR stop, G+3 One No. lift) with fan, fully automatic state of the art technologies, make from World Fame manufactures (Make:- Thyssen/ MITSUBISI/ SCHINDLER/KONE/JOHNSON/OTIS is Banned for Bad Service Regulation. with all complete job .

Maintenance Cost for 5-Years (CAMC) with Tax :-Note :- Maintenance/Replacement of all Parts included.

Supply / Installation and Commissioning of 24 Port Network Switch GIGA PoE,IEEE 802.3at and IEEE 802.3af Power over Ethernet (PoE) compliant,24x10/100/1000 Mbps Auto-MDIX PoE ports,Provides up to 30 watts per PoE port,PoE power budget 370W,4 KV surge protection for PoE ports,IEEE 802.3x flow control support,Plug-and-play installation,8.8 Gbps switching fabric,2.75 Mbits RAM Data Buffer,4K MAC address entries,Sturdy metal enclosure

Category 6, UTP 24-Port Patch Panel Size - 482.6mm x 44.2 (19’’ x 1U), Panel Material - Steel-fully powder coated, Unshielded - RJ 45, Plug Insertion Cycle - 750 times DC Resistance- 72Ω max, Voltage Rating - 72 Vdc max, Current Rating - 1.5A max

Supply / Installation and Commissioning of Junction Boxes, Outdoor Box for Camera

Supplying and fixing of RJ 45 computer socket suitable for Cat 6 on module GI box along with base & cover plate in surface or in recess including making connection, soldering etc. as required.

Category 6 UTP Patch Cords - 1 Mtr Standard Colour - Blue, Grey, Yellow, RJ45 Plug - Polycarbonate plug, Current Rating - 1.5A max, Insulation Resistance - 500MΩ/km(min)@500 Vdc, Contact Resistance - 15 mΩ (max) per contact

Category 6 UTP Patch Cords - 2 Mtr Standard Colour - Blue, Grey, Yellow, RJ45 Plug - Polycarbonate plug, Current Rating - 1.5A max, Insulation Resistance - 500MΩ/km(min)@500 Vdc, Contact Resistance - 15 mΩ (max) per contact

Supply fitting fixing Rack 19" 12U fully powder coated complete etc as required with complete accessories (5 amp x 6 socket, wire manager, rack fan) VALRACK/ Netrack make. Wit all necessary items.

Supplying and drawing of UTP 4 pair CAT 6/Cat 6 E LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.

Smart-UPS On-Line, 5.4 kW / 6 kVA with 1 hour Backup12 V 65 AH SMF Battery UPS Toplogy Double Conversion On-Line, Power Rating (VA / Watts) 5400Watts/6000VA, Form Factor Rack/Tower Convertible; Output Power Capacity 5400 Watts/6000 VA, Max Configurable Power 5400Watts/6000VA, Nominal Output Voltage 230V, Output Voltage Note Configurable for 220 : 230 or 240 nominal output voltage, Efficiency at Full Load 94.00%, Output Voltage Distortion Less than 3%,Output Frequency (sync to mains) 50/60 Hz +/- 3 Hz,Crest Factor 03:01,Waveform Type Sine Wave, Output Connections (1)*Hard Wire 3-wire (8)*(H N + G) IEC 320 C13(8),Bypass Built-in Bypass, Output Short Circuit Protection Yes,Parallel Redundancy (Option) 1 + 1, Nominal Input Voltage 230V,Input Power Factor>0.98,Input Frequency 40-70Hz,Input Connections Terminal Block, Protection Thermal Circuit Breaker (250VAC/20A), Input voltage range for main operations full load 160 - 285V, Input voltage range for mains operation half load 160-285V, High Voltage withstand Capability 420 VAC, Green Mode Range 210-250 VAC (230 V), Battery Type Mintenance - free sealed Lead-Acid battery with suspended, electrolyte. 12V 65 Ah SMF battery for 60 Min Battery Back up.

SITC of 2MP IR Indoor Dome Fixed Camera- 1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps, 2.8 mm Fixed lens, Color: 0.01 Lux at F1.2, ICR, ONVIF, support H.265, H.264, MJPEG, DWDR, 3D Digital Noise Reduction, Tripple individually configurable stream, 12 VDC & PoE, IR range: 40m, IP67, IK10, Edge Anlalytics- Line crossing detection, intrusion detection, Motion detection, video tampering, UL, CE, FCC certified. (DS-2CD3121G0-I (2.8 mm) (Approved Makes: Hikvision/ Honeywell/ Bosch)

SITC of 2MP IR Bullet Fixed Camera -1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps, 2.8 mm Fixed lens, 0.01 Lux at F1.2, 0 Lux with IR, ICR, ONVIF (PROFILE S), support H.265, H.264, MJPEG, DWDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, IP67, Edge Anlalytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Video tampering, UL, CE, FCC certified. (DS-2CD3021G0-I (2.8 mm) (Approved Makes: Hikvision/ Honeywell/ Bosch)

SITC of 64 ch Network Video Recorder - Connect Up to 64 IP Cameras, Dual OS, Up to 12 Megapixels Resolution, Two independent HDMI outputs, one HDMI output of 4K resolution,1 VGA output with output upto 1920 × 1080, Support H.265, MJPEG, Supports N+1 hot spare system,Supports RAID0, RAID1, RAID5, RAID6 and RAID10 ,Supports HDD hot swap, Supports Dual Power-Redundant, Incoming Bandwidth 320 Mbps, 8 SATA Hard Disks, ANR Technology, 8 SATA interfaces for 8 HDDs and capacity of each HDD upto 6TB, 3 × USB at least 1 × USB with 3.0, Alarm I/O 16/4, RS-485, RS-232, 2 RJ-45 10 /100/1000 Mbps self-adaptive Ethernet interface, Multiple network monitoring: Web viewer, CE, FCC, UL certified. (DS-7764NI-I8) (Approved Makes: Hikvision/ Honeywell/ Bosch)

SITC of 16 port Unmanaged Network PoE Switch: 24 port PoE Switch with PoE standard of IEEE 802.3af , IEEE 802.3at, PoE port, Uplink ports (DS-3E0326P-E) (Approved Makes: Hikvision/ Honeywell/ Bosch)

Category 6, UTP 24-Port Patch Panel Size - 482.6mm x 44.2 (19’’ x 1U), Panel Material - Steel-fully powder coated, Unshielded - RJ 45, Plug Insertion Cycle - 750 times DC Resistance- 72Ω max, Voltage Rating - 72 Vdc max, Current Rating - 1.5A max

Category 6 UTP Patch Cords - 1 Mtr Standard Colour - Blue, Grey, Yellow, RJ45 Plug - Polycarbonate plug, Current Rating - 1.5A max, Insulation Resistance - 500MΩ/km(min)@500 Vdc, Contact Resistance - 15 mΩ (max) per contact

Hard disk 6 TB

19 U Network Rack (Brand - Valrack / Netrack / Legrand)

CAT 6 Cable for CCTV camera (Brand - Digilink / Legrand / Molex)

Cable laying with PVC conduit ISO Certified

CCTV installaiton configuration & testing

32" Full HD LED Display for CCTV

Providing and fixing M.S. pipe to I.S. 1239 (Heavy class) complete with all supports & fittings like, unions, couplings, bends, elbows, tees, offsets,reducers, flanges as per table 'E' etc. to complete the work as per the requirement at site including painting with one coat of primer after surface preparartion and two coats of synthetic enamel paint, cutting and making good the walls good complete. Pipe upto 40 mm dia threaded joints with holdtite, 50 mm dia and above should be welded joint ( all type) (internal works/External Works).

Meter

Meter

Meter

Meter

Meter

Providing and fixing cast iron dual plate wafer type non return valves of PN1.6 including nuts, bolts,1.5mm thick compressed asbestos gasket including matching flanges as per table "E" complete

Providing and fixing C.I. butterfly valves PN 1.6 complete with bolts, nuts 1.5mm thick compressed asbestos gasket companion flanges as per table "E" complete.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as

Providing and fixing first aid fire hose reel drum wall mounting, swinging type(Powder coated finish in fire red) fitted with 20 mm dia. 30 m long high pressure hose(IS:444, Type-2) with 5 mm outlet SS nozzle with shut off valve (IS:8090). complete hose reel drum shall be conforming to IS:884) 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle.Drum and brackets for fixing the equipmets on wall.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Gunmetal

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

Gunmetal

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :

3 way - 150 mm dia M.S. Pipe

Providing and fixing of self illuminated / auto glow "EXIT" signs printed on photoluminescent sheet containing self illuminated base chemical, of appropriate size not less than 400 x 150 mm, suspended from ceiling or fixed to the walls with accessories as required and as directed at site.

a)Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS1520. (b) Suitable HP Squirrel cage induction motor, TEFC ,synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation,conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads.

INCOMING : Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required :

a) Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump)

a) Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Drive Pump)Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.

32 bit microprocessor based Intelligent Addressable Fire Alarm Control panel with 2 loops with battery back up. The panel would be modular, decentralized, with The panel shall be consisting with minimum 240 character LCD display and for networking. The Panel would be able to record atleast 60,000 events history. Each loop would be capable to have atleast 250 addressable detectors and addressable devices with up to 3.5km loop length. Make: Schrack Seconet (Vds approved)

1 KVA LINE INTERACTIVE UPS WITH 30 MIN BATTERY BACK UP

Supplying and fixing Intelligent Addressable type multicriteria detector with base for use as heat or smoke or combined both with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd.

Supplying and fixing Intelligent Addressable type Heat detector with base with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd.

Sypplying and fixing Intelligent Addressable Manual Call Point having inbuilt short circuit isolator i/c testing and commissiong etc as reqd.

Addressable sounder with interface module, power supply for sonder and programmable by software having integrated short circuit isolator & having operating temperature -10⁰C to + 55⁰C

Analogue Addressable Control module with IP66 casing containing four relay outputs, Each containing a potential-free DPDT contact with a fail-safe and in-built short circuit isolator The ambient temperature range shall be -20C to +60C.

Duel LED Response Indicator (LOCAL)

4"/4" JB for mounting of detectors & other accessories with necessary fittings

Supplying and fixing Outdoor Electronic Sounder with 4 distinct tone including 40W Speaker with required accessories as reqd.

Supplying and laying of 2x1.5 sq.mm. ISI marked copper armourd conductor cable with gland scoket and other wiring accessories on the existing surface/tray/shaft etc as reqd

SITC of 50 LPH RO Water Purifier alng with RO-AUTO MAX 50 lph, hdrophenumatic tank-10 LPH, Faucet-1 nozzle, accessories- clip, inlet & outlet pipe etc.

Supply,installation,factory testing and commissioning, engineering of silent Diesel Engine driven generating set 415 volts, 3 phase 4 wire,RPM 1500 engine as per IS:10001/ 10002 and Alternator as per IS: 13364 complete with isolator panel, relay panel, AMF Panel and switch gears for automatic starting on main failure, control panel having meter and sound proof canopy,Exhaust System for DG as per CPCB norms etc. of capacity, complete in all respect as following.

Supply, installation, testing and commissioning of 500 kVA, Fully Copper 11kV/433V, 3 phase, 50 Hz, Delta star, DYn11, Dry type, cast resin, indoor, natually cooled, copper double wound transformer with Off load tap changer from +5% to -10% in steps of ±2.5%, class F insulation, complete with WTI and scanner for alarm & trip, unidirectional rollers, cable end box for termination of HT cables & Bus duct for LT side complete with rating and technical name plate, earthing terminals with lugs, lifting lugs in all respect with all necessary standard accessories and as per IS. The transformer shall have suitable enclosure for providing neutral CT on earthed star point with connector for connection to REF relay provided in Main panel. All routing test as per IS shall be conducted on the transformer. The Transformer Enclosure shall have suitably designed Louvers for Air Circulation & efficient Cooling. The enclosure shall be Epoxy Powder coated. The transformer shall be subjected to all routine tests as per IS/IEC standards. Type test certificate shall be submitted. The transformer shall meet latest ECBC requirments.Make-Servokon / Schnneider/ Siemens/Powerstar/Infra Power/C&S etc of Higher grade.(Electrical Inspector Charges included)

11 KV DOUBLE POLE STRUCTURE:- Supply, erection, testing and commissioning of 2 pole structure for providing 1 No. 11KV,400A GOS in accordance with IE rules, & local authority specification and drawings and comprising of the following items below.

Supply of Conductor of 25 x 3 mm strip flat of material Cu used in air termination and down conductor system. used in air termination and down conductor system . Cross sectional area of conductor should be 50 mm². Test Parameter: a.Lightning impulse current of 100kA for 10/350 µs b.Electrical resistivity - 0.036 µΩm, Tensile strength - 120 to 240 MPa or N/mm², Salt spray - No Sign of Corrosion.Tested as per IEC 62561-2.

Supply of UV resistance Porcelein wall insulator for holding 25 x 3 mm copper strip flat Conductor .

Supply of Gunmetal Cross Connector for 25 x 3 mm dia copper strip flat. Test Parameter:Salt Spray Test ( IEC 62561-1) - No sign of Corrosion

Supply of air termination rod of 1.5 meter length of material Cu bonded of diameter 16 mm. Crown of rod should be pure copper with 5 spikes. The rod shall be mounted with clamp and fixing accessories. Test Parameter: Mechanical Load Test for individual aluminium alloy rods - 120 to 280 N/mm² Salt Spray Test-No sign of corrosion Tested as per IEC 62561-1&2

Supply of Lightning counter - LCD screen shows the number of lightning strikes, hour and date of lightning events Buttons enable TIME/DATE setting and log viewing. Replaceable battery, working life minimum five years, Complies with IEC/EN 62561-6.

Supply of upply of Metal Box Test Joint Point with enclosure between 25 x 3 mm Cu Strip Flat. Test Parameter: Salt Spray Test for test joint plate -No sign of Corrosion .Tested as per IEC 62561-1

Supply of UL Listed Maintenance Free Copper bonded Earth rod of 3048mm length having the dia of 14.2 mm with copper coating thickness of 254 microns. The rod has been tested for Dimension, Marking, Tensile Strength, Salt mist, coating thickness,Electrical resistivity test before and after corrosion test as per IEC 62561-2 & UL 467.Supply of earth enchancing mineral compound tested for leaching and TCLP with NABL accredited Lab as per IEC 62561-7 -25 kg Supply of Earth rod Clamp made up of stainless steel terminating cable / flat conductor.Supply of Earth Chamber Inspection Pit made up of poly propylene material.

Installation of Air Terminal, Copper Strip 25 x 3 flat, Earthing System Set, etc

Providing and fixing following dia RCC pipe NP2 class(light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement: 2 fine sand) including trenching (75 cm deep) and refilling etc.as required.

Meter

Meter

3.5 core, 300 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electric cable with aluminium conductor.

Providing and fixing of signages,modular FLAT frame techology of various width and lengths to form suggested usages made of aluminium extruded sections duly anodised all signages shall be provided with 0.6-0.8mm polycarbonated protecting film over the prints of appropriate size, print shall on 0.6mm coated , YUPO make biodegradable sheet printed on HP 4500 UV flat bed printer.

3mm aluminium Composite panel,duty cut by CNC router,Letter should be of SS grade 304 Steel/corrosion ressistant/high strength hardened/plasma cut with nitrogen to give excellent surface finish for edge grinding and fabrication of letter welding all complete job as per direction of E/I. Letter Size : 15 inch FAMILY COURT CUM MEDIATION CENTRE,KISHANGANJ

Providing & Fixing of Single Piece of Fabric white colour blackout ( Pollyvinal Coloride ) Which Wraps around a Casing and Fits into the top of Window Frame , Either within or Outside of Window recess. The ROLLER BLINDS is Operated by a pull cord ( alluminium channel ) attached to the bottom of the blinds or by a side - winding chain mechanism attached to the blind casing

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering taxes, royalty all complete as per building specification and direction of E/I.

Providing and laying in position mixed design mix M-30 grade in Column do - do all complet job

Beams, plinth beams, girder, bressumers, cantilevers, Suspended floors, lintels, roofs and staircase including spiral staircase, shelves etc.

Providing M30 grade R.C.C instead of M20 grade R.C.C do - do all complet job

Brick work with fly ash bricks in cm (1:6) do - do all complet job

Extra brick work in Super Structure

Centring and Shutring in do - do all complet job

Suspended floor

Roof Beam

Column

Stair

Chajja

Reinforcement for R.C.C Work do - do all complet job

8 mm tor bar

10 mm tor bar

12 mm tor bar

16 mm tor bar

20 mm tor bar

25 mm tor bar

Providing and applying white cement based putty of average thickness 2 mm do - do all complet job

Distempering with oil bound washa ble distemper of approved brandand manufacture to give an even shade .

Applying one coat of cement primer of approved brand do - do all complet job

Finishing walls with Acrylic Smooth exterior paint do - do all complet job

Forming groove of uniform size from 12x12 mm do - do all complet job

Making khurras 45 x45 cm do - do all complet job

Providing and fixing on wall face U-PVC molded fittings do - do all complet job

Providing and fixing U-PVC Pipe clip do - do all complet job

Providing and fixing inlet mouth rain water pipe do - do all complet job

Providing and fixing M.S rivets do - do all complet job

Providing and fixing wpc frame do - do all complet job

Providing and fixing 35 mm thick factory made wpc door do - do all complet job

Providing and fixing in position collapsible steel shutter do - do all complet job

Providing and fixing Three track sliding window with fly proof S.S wire mesh do - do all complet job

Extra for providing heavy sheet float glass panes instead of ordinary float glass in glazed doors,windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Filling the gap in between aluminium frame & adjacent RCC/ Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.

Providing and fixing alluminium sliding tower bolt do - do all complet job

Providing and fixing alluminium hanging floor door stopper do - do all complet job

Providing and fixing M.S Grill do - do all complet job

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes do - do all complet job

Applying priming coat With ready mixed zinc chromate yellow primer do - do all complet job

Painting with ready mixed paint of approved brand do - do all complet job

Treatment of soil under existing floors using chemical emulsion do - do all complet job

Providing and Fixing 15 mm thick calcium silicate false ceiling tiles do - do all complet job

Providing and fixing skirting with Pre-laminated do - do all complet job

Providing wood work in frames of doors, windows do - do all complet job

Providing and fixing 12 mm thick pre-laminated particle board do - do all complet job

Providing and fixing 38 mm thick parquet (wood block) flooring do - do all complet job

Providing and fixingFly proof stainless steel grade 304 wire gauge do - do all complet job.

Providing and fixing 1 mm thick M.S sheet door do - do all complet job.

Providing and fixing cast iron box for fan clamp do - do all complet job.

Providing and laying water proofing treatment to vertical & horizontal. Surfaces of depressed portion of WC. Kitchen and the like consisting …...do - do all complite job

1:3 (1 cement: 3 coarse sand)

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3mm thick water proofingmembrane, black finishedreinforcedwithnon-wovenpolyestermatt consistingofacoatof bitumenprimer for [email protected] litre/ sqmby thesame membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity70-160cps.Over theprimercoat thelayerofmembraneshallbe laidusingButaneTorch and sealingall joints etc., andpreparing the surface complete. The vital physical and chemical parameters of the membraneshallbeasunder:Jointstrengthinlongitudinalandtransverse directionat 23°Cas650/450N/5cm. Tear strength in longitudinal and transversedirectionas300/250N.Softeningpointofmembranenot less than150°C.Coldflexibilityshallbeupto-2°Cwhentestedinaccordance withASTM,D-5147.Thelayingofmembraneshallbegotdonethrough the authorised applicator of the manufacturer of membrane

Cement concrete flooring 40 mm thick 1:2:4 do - do all complite job

Cement plaster skirting (upto 30 cm hieght) do - do all complite job

Providing and fixing white vitreous china water closet squatting pan (Indian type WC pan) with 100mm sand cast Iron P or S Trap, 10 litre low level PVC flushing cistern (of approved make) with fittings CI/MS brackets, 32 mm diameter flush pipe with fittings and clamps, over flow arrangement with specials and mosquito proof coupling of approved municipal design including painting of fittings and brackets, cutting and making good the walls and floors wherever required.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

Providing and fixing white vitreous china wash basin with C.I. / M.S. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required.

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing 600 x 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers comelete.

Providing and fixing toilet paper holder:

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gms.

Providing and fixing soil, waste and vent pipes.

Providing and fixing M.S. holder bat clamps of approved design to sand cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) including cost of cutting holes and making good the walls etc.

Providing and fixing plain bend of required degree

Providing and fixing single equal plain junction of required degree with acesses door, insersion rubber washer 3mm thick, bolts and nuts complete.

Providing and fixing terminal guard.

Providing and fixing collar

Providing lead caulked joints to sand cast iron / centrifugallly cast (spun) iron pipes and fittings of diametre:

Providing and fixing M.S stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diametre.

Providing and fixing sand cast iron trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors.

Painting sand cast iron/centrifugally cast (spun) iron soil waste vent pipes and fittings with paint of any colour such as chocolate gray or buff etc. over a coat of primer (of approved quality) for new work.

merter

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

75 mm diameter

110 mm diameter

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for therma expansion.(SW)

Coupler

Shoe plain

Providing and fixing G.I. pipe complete with G.I. fittings and clamps, including, cutting and making good the walls etc. (internal work)

15 mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40 mm dia nominal bore

Painting of exposed pipes with two or more coats of synthetic enamel paint of approved quality over a coat of red oxide zinc cromate primer including painting of legends in English with direction arrows.

15 mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40 mm dia nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

15mm nominal outer dia pipes

20mm nominal outer dia pipes

Providing and fixing brass stop cock of approved quality :

15 mm dia

20 mm dia

Making connection of G.I distribution branch with G.I main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete.

25 to 40mm nominal bore

50 to 80mm nominal bore

Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end).

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

Providing and fixing gun metal non-return valve of approved quality (screwed end).

32 mm nominal bore

Vertical

Providing and placing on terrace (at all floor levels) polythylene water storage ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing PTMT grating of approved quality and colour.

150mm nominal size square 100mm diameter of the inner hinged round grating.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy aluminium rod with L.P / H.P.H.D plastic ball.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS : 8931

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

Providing and fixing uplasticised PVC connection pipe with brass unions:

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms

Office Table with Side Unit Size-(L)2000mm X (D)1800mm X (H)755mm No Of Drawers3 No Of Shelves 5 Add Ons Interchangeable Side Runner Finish Matte Size Large Style Contemporary-is a suave . Table top thk 40mm Made with a combination of engineered wood, this gorgeous desk has contrasting panels in black for a contemporary look. Coupled with a runner and storage for your files and cabinets, the Clint is a desk meant for the discerning tycoon. With a warm walnut finish, the dual tone finish of the desk adds to its overall style and finish. With an option of regular drawers and shuttered glass storage units you can take a pick of which unit suits you the best.The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

High Back Revolving Chair- Chair Size (W)660mm X (D)500mm X (H)1265mm. Made From High-Density Foam, The Sink-In Cushions And The Cradling Backrest Provides Contouring Comfort For All-Day Seating. The Soft To Touch Premium Leatherette Upholstery Add Elegance To Its Look While Also Making It Stain & Fade Resistant. Features Such As Synchro Multi-Locking Mechanism, Pneumatic Height Adjustment, Tilt Tension Control, Etc, Let You Find Your Ergonomic Position With Ease. The Pneumatic Height Adjustment Along With The Thick Padded Headrest And Armrest Further Let You Sit In Absolute Comfort. A Strong Chrome Base Supports The Structure While The 360 Swivel And 55Mm Castors. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

CANTILEVER CHAIR - Cantiliver Chair Size-(W-480mm D-490mm I Back H-530mm, W-480mm I Height Min-460mm Max--- Back max height with cantilever - 940mm, Back min height with cantiver - 460mm. Seat & Back made up of 14mm thick boiling water proof plywood os ISI303. Back reclines at A 2-to-1 ratio to the seat. 5% post consumed recycled content & 30% total recycled content. Color-Black. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

High Back Chair Size (Back Height-670xBack Width-470)mm & (Seat Depth-485xSeat Width-475)mm with Min-Max Height (460-540)mm. Nylon base chair with push back mechanism & Fix handle. Nylon base chair with push back mechanism. Back & seat cover cushion chair uphlostered in fabric & adjustable armrest locks any position. Syncro mechenism with locking system and five star chrome base with nylon casters. Seat & Back made up of 14mm thick boiling water proof plywood os ISI303. Chair rotates a full 360 degree in either direction for ease of motion. Standard on every executive with task chair & controls rate and ease with which chair reclines to different weight and strengths of users. Quick and easy adjustment regulated height of chair relative to floor. Back reclines at A 2-to-1 ratio to the seat. 5% post consumed recycled content & 30% total recycled content. Color-Black. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

Visitor Chair- Cantiliver Chair Size (Back-H-470xW-460, Seat-D-460x470)mm & Min. Height-430mm. Multipurpose fixed cantiliver chair & armrest with pading & metal base. A 14mm thick, BWR grade plywood (IS:303) is used to make the seat and back. Deep cushioned back and seat confirm to body contours for proper aligment, posture and all day comfort. 5% post consumed recycled content & 30% total recycled content. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

Visitor Chair - Chair Size (W)595mm X (D)510mm X (H)875mm. Multi-purpose fixed chair,Metal frame,PU Padding on armrest. Cushion upholstery in leatherette with four leg metal legs with matt finish. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.. Color-Black

Steel Almirah - Almirah Size (L)915MM X (D)485MM X (H)1980MM OFFICE STOREWELL WITH 4 SHELVES GAUGE: BODY: 22 GAUGE *DOORS: 20 GAUGE. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

3 Seater Sofa - 3 Seater Sofa Size - (W)1760mm X (D)720mm X (H)845mm. Fine Finesse. The Jesse sofa is contemporary style looks like. This sofa is sleek and comfortable. The sleek frame is finished in a rich polish with split panel seating. The back and seat have medium to firm cushioning for better posture. The Leg of Solid wood in glossy finished. Frame used is treated American pine wood with termite free & borer free. Soft & comfortable cushion with high density and resilient foam. Frame used is Treated american pine wood & the wood used in sofa has been 8% moisture, this prevents the wood from wrapping and bending. all wood used is termite free and borer free. Foam of sofa comfortable cushion with high density and resilent foam. all apholstry materials used in specially designed.Color-Camel/Green.The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

2 Seater Sofa - 2 Seater Sofa Size:(L)1200mm X (D)720mm X (H)845mm. Fine Finesse. The Jesse sofa is contemporary style looks like. This sofa is sleek and comfortable. The sleek frame is finished in a rich polish with split panel seating. The back and seat have medium to firm cushioning for better posture. The Leg of Solid wood in glossy finished. Frame used is treated American pine wood with termite free & borer free. Soft & comfortable cushion with high density and resilient foam. Frame used is Treated american pine wood & the wood used in sofa has been 8% moisture, this prevents the wood from wrapping and bending. all wood used is termite free and borer free. Foam of sofa comfortable cushion with high density and resilent foam. all apholstry materials used in specially designed.Color-Camel/Green. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

Wooden Center Table - Center Table (L)1130mm X (W)630mm X (H)410mm. The centre table is made keeping your comfort in mind. The sheen on the glass table top will ensure you are the envy of many a neighbour. Inlaid onto a solid wood frame that slopes inward, the table is a gorgeous piece of furniture to highlight your living room. The turned wooden legs are sleek and sturdy providing the table with its support. The wood work below the glass provides the glass with a focal point and some support. Add volumes of style to your living room with the Hopper centre table. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

Corner Table- (Dia) 390mm X(H)460mm The sleek compact table made of solid wood has a touch of style. Perfectly crafted slim tabletop & miniature design.Base is made of exquisitely crafted three curved leg base. Stylish base of the table brings an lavish look to the table.The rich finish of table enhances the table. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

High Back Chair with revolving - Size (W)590mm X (D)505mm X (H)1280mm. Chrome plated base with gas height adjustment and central tilting with single locking machenaism. Armrest with padding. Leatherette uphlostery has the look and feel of top grain leather. Cushion wtih lumber support for all day comfort. Chrome plated loop armrest with padded upholstery for extra comfort. chair rotates a full 360 degree in either direction for ease of motion. Standard on every executive & controls rate and ease with which chair reclines to different weight and strengths of users. Quick and easy adjustment regulated height of chair relative to floor. Look out tilt function when chair is in upright position. 5% post consumed recycled content & 30% total recycled content. Color-Black.The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

Mid Back Chair- (Back Height-495xBack Width-470)mm & (Seat Depth-485xSeat Width-475)mm with Min-Max Height (410-470)mm. Nylon base chair with push back mechanism & Fix handle. Back & seat cover cushion chair uphlostered in fabric & adjustable armrest locks any position. Syncro mechenism with locking system and five star Nylon base with nylon casters. Seat & Back made up of 14mm thick boiling water proof plywood os ISI303. Chair rotates a full 360 degree in either direction for ease of motion. Standard on every executive with task chair & controls rate and ease with which chair reclines to different weight and strengths of users. Quick and easy adjustment regulated height of chair relative to floor. Back reclines at A 2-to-1 ratio to the seat. 5% post consumed recycled content & 30% total recycled content. The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

3 Seater Chair - Chair Size - Length 1775mm x Depth 690mm x Height 755mm 1)Seat & back single section 2)Seat is 410 mm from ground 3)Perforated mild steel powder coated 4)Seat thickness 1.2 mm 5)Seat width 520 mm 6)Beam MILD steel with black power coating thickness 1.6mm 7) Mild steel border with chrome plating for every seat & back 8) Mild steel handles chrome plated & die pressed legs at the end of chairs 9) Gross weight of regular 3-seater will be 31 kg.The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

Stackable Café Chair : Size: (L)381mm X (D)419mm X (H)839mm Seat and back in PVC Moulded Chair with SS 202 grade frame Round Pipe. The Product Should be Certified Company BIFMA,ISO-50001,Green Guard/Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC & PEFC.

3 Seater Sofa- Sofa Size( (L)1905mm X (D)890mm X (H)870mm)mm. Arm height 620mm, Seat depth 510mm, Back Height 460mm. Frame used is treated American pine wood with termite free & borer free. Soft & comfortable cushion with high density and resilient foam. Frame used is Treated american pine wood & the wood used in sofa has been 8% moisture, this prevents the wood from wrapping and bending. all wood used is termite free and borer free. Foam of sofa comfortable cushion with high density and resilent foam. all apholstry materials used in specially designed. all plywood used in M R Garde. Color-Black/Brown.The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

2 Seater Sofa- Sofa Size (W)1410mm X (D)890mm X (H)870mm. Arm height 620mm, Seat depth 510mm, Back Height 460mm. Frame used is treated American pine wood with termite free & borer free. Soft & comfortable cushion with high density and resilient foam. Frame used is Treated american pine wood & the wood used in sofa has been 8% moisture, this prevents the wood from wrapping and bending. all wood used is termite free and borer free. Foam of sofa comfortable cushion with high density and resilent foam. all apholstry materials used in specially designed. all plywood used in M R Garde. Color-Black/Brown.The Product /Company Should be Certified Company BIFMA,ISO-50001,Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, ISO14001, 18001 & PEFC.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit with modular switch , modular plate, suitable size G.l. box etc as required

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate/,switch box including connections but excluding modular plate etc. as req u ired

Wiring for light/ power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface /recessed PVC conduit as required.

2x2.5 Sq.mm +1x2.5 Sq.mm

4 X 4 sq. mm + 1 X 4 sq. mm earth wire

4 X 6 sq. mm + 1 X 6 sq. mm earth wire

4 X 10 sq. mm + 1 X 10 sq. mm earth wire

4 X 16 sq. mm + 1 X 16 sq. mm earth wire

Supplying and fixing PVC/G.I box of 200mm x 250mm x 60mm deep on surface or in recess with suitable size of phenolic laminated sheet cover in fornt including painting etc as required (Adopter box above each D.B).

Supplying and fixing suitable GI Box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 and 15/16 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc. as required. (for power plug )

Supplying and fixing suitable size G.I Box with modular plate and cover in front on surface in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc., as required. (for light plugs to be used in non residential buildings )

Supplying and fixing 12 modules GI box along with moduler base & cover plate surface or in recess including providing and fixing of 2 no 5 pin 5/6 amps socket outlet with 2 no 5/6A moduler type switch, 1 no 6 pin 15/16 amps socket outlet with 1 no 15/16A moduler type switch ,Telephone , and 6/32 amps SP connection etc. as required.

Supply & fixing 4 way(4+12) double door TP & N, sheet steel, MCB distribution board, 415 volts, on surface/ in recess, complete with tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc.as required (But without MCB / RCCB / Isolator) light DB

S/F Electronics Musical call bell suitable for D.C/A.C. single phase 230 copmplete as required.

Supplying and fixing batten/angle holder incluiding connection etc as required.

Supplying and fixing 2 pin,6 amp,celling rose on the existing junction box / PVC box incluiding connection etc as required.

S/F modular blanking plate on the existing modular plate and switch box excluding modular plate as required.

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required'

Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required.

Providing and fixing following capacity busbar chamber with 4 strips of suitable size made of copper, heavy duty,complete with all accessories including connections, earthing the body etc. as required.

Supplying and fixing wall/floor mounted cubical panel board, fabricated with 16 gauge iron sheet, suitable for panel mounted switch disconnector, including bus-bar chamber, insulator and painting etc. as required. (but without busbar copper strip)

Providing and fixing MV danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

P/F 4.00 mm dia.copper wire on surface or in recess for loop earthing along with existing surface /recess for loop earthing along with existing surface/recessed conduit /submain wiring/cable etc required.

P/F lightning conductor final, made of 25mm dia. 300mm long, copper tube having single pron on top with 85 mm dia 3 mm thick copper base palte including holes etc complete as required.

P/F copper tape 20mmx3mm thick on parapet or surface of wall for lighting conductor complete as required ( for horizontal run)

P/F copper tape 20mmx3mm thick on parapet or surface of wall for lighting conductor complete as required ( for vertical run)

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required.

Metre

Supply and installation of regular/standard model A.C. ceiling fan of 1200 mm sweep with service value (CM/MM) minimum 4.00, Air delivery minimum 270 cum/min including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated copper conductor etc as required.

Supply & Installation 400 mm dia 230 volt AC wall /cabin Fan including fixing the bracket making connection testing commissioning etc as required

Supply and fixing of following sweep/ sizes PVC/ABS square body Exhaust Fan with automatic openable louvre shutter in existing opening including making connection, testing etc as required

200 mm sweep (1300/1400 RPM)

Supplying and fixing recess/surface mounted downlighter with minimum efficacy 100 lm/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required

Supplying and fixing of following types lamp in the existing nelectrical fitting/ fixtures etc. as required

Supplying and fixing recess mounted 36 watt LED flat panel (2' X 2') with minimum efficacy 100 lm/w which privides soft light and glare free symmetrical illumination suitable for armstrong/grid ceiling and integrated electronic driver etc directly on false ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing 2'X9 watt LED batten with minimum efficacy 100 lm/w in polycarbonate housing and complete with integrated electronic driver etc directly on wall/ ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor etc. as required.

Supplying and fixing following sizes of PVC conduit along with accessories in surface /recess including cutting the wall and making good the same in case of recessed conduit as required.

SITC of water cooler capacity storage 40*80 liter body stainless steel diamention 665*485*1210 mm. Tank capacity 80 liter and cooling water supply 40 liter per houre and Ro purifiers 20 liter capacity per hour water supply with all accessoriees including. Make- kent/usha/blue star/Climatrol/Voltas/Aquaguard.

SITC AC split(1.5 ton) with stabilizer ISI standard as per specification 5 star inverter AC.

Supply, Installation, Testing and Commissioning of 2.0TR Cassette Ac 5 Star with high quality black fin corrosion resistance and Air purification which contains ioniser,deodorisation filter,dust electrification, pre- filter. Super 5 star comes with (5.2) ISEER Rating.Eco-Friendly R32 Refrigerant highly efficient with a lower global warming potentials compared to R410.

Supplying and fixing modular type 25 amps A.C. unit box with ON/OFF MCB on surface or in recess complete with connections, testing and commissioning etc as required.

Stabilizer (2/1.5 Ton) ISI Standerd As per Specification

Extra copper piping electrical wire for split AC

Extra drain pipe split AC

Stand of Outdoor Unit

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power H.T. cable with aluminium conductor for working voltage upto 11 KV as required.

Providing and fixing 25 mm x 5 mm thick GI strip on surface or in recess for connections etc. as reqd.

8 Passenger(408 Kg), (G+1) Floor Add Extra for machine room less(MRL) Rs 159300.00

Annual Maintenance Cost of Lift

First Year (Free with SITC)

SECOND YEAR LIFT COST OF 5% for Add Floor

THIRD YEAR LIFT COST OF 6%

Supplying and drawing of UTP 4 pair CAT-6 LAN cable in the existing surface/recessed steel /PVC concuitas required.

Category 6 UTP Patch Cords - 1 Mtr Standard Colour - Blue, Grey, Yellow, RJ45 Plug - Polycarbonate plug, Current Rating - 1.5A max, Insulation Resistance - 500MΩ/km(min)@500 Vdc, Contact Resistance - 15 mΩ (max) per contact

Category 6 UTP Patch Cords - 2 Mtr Standard Colour - Blue, Grey, Yellow, RJ45 Plug - Polycarbonate plug, Current Rating - 1.5A max, Insulation Resistance - 500MΩ/km(min)@500 Vdc, Contact Resistance - 15 mΩ (max) per contact

24-port GbE Smart Managed Switch with GbE Uplink Interfaces-24 Ports 10/100/1000Mbps+4 SFP;Port Standards & Functions-IEEE 802.3 10BASE-T Ethernet (twisted-pair copper),IEEE 802.3u 100BASE-TX Fast Ethernet (twisted-pair copper),IEEE 802.3ab 1000BASE-T Gigabit Ethernet (twisted- pair copper),IEEE 802.3az compliance Auto-negotiation,IEEE 802.3x Flow Control; Full/Half Duplex-Full/half duplex for 10/100 Mbps speeds,Full duplex for Gigabit speed;Media Interface Exchange Auto MDI/MDIX adjustment for all twisted-pair ports;Switching Capacity 56 Gbps; Transmission Method Store-and-forward; MAC Address Table 16,000 entries per device, Maximum 64 bytes packet forwarding rate 41.7 Mpps,Packet Buffer Memory 1.5 MB,Maximum Power Consumption 22.45 watts, Standby Power Consumption 17.84 W/240 V, Acoustics 0 dBA Heat Dissipation 76.55 Btu/hr, Operating Temperature -5 to 50 ˚C (23 to 122 °F), Storage Temperature -20 to 70 ˚C (-4 to 158 °F), Operating Humidity 0% to 95% non-condensing, Storage Humidity 0% to 95% non-condensing, Diagnostic LEDs Link/Activity/Speed (Per 10/100/1000 Mbps port), Certifications CE (LVD) BSMICCC, C-Tick. Netgear / D-link/ Cisco.

Category 6, UTP 24-Port Patch Panel Size - 482.6mm x 44.2 (19’’ x 1U), Panel Material - Steel-fully powder coated, Unshielded - RJ 45, Plug Insertion Cycle - 750 times DC Resistance- 72Ω max, Voltage Rating - 72 Vdc max, Current Rating - 1.5A max

Supply fitting fixing Rack 19" 12U fully powder coated complete etc as required with complete accessories (5 amp x 6 socket, wire manager, rack fan) VALRACK/ Netrack make.

Supplying and fixing of RJ 45 computer socket suitable for Cat 6 on module GI box along with base & cover plate in surface or in recess including making connection, soldering etc. as required.

Wireless N Access Point Interface - One 10/100Mbps RJ45 Port (Auto MDI/MDIX), Button - WPS Button, Reset Button, External Power Supply - 9VDC / 0.6A, Antenna Type - 5dBi Detachable Omni Directional Antenna, Frequency - 2.4-2.4835GHz, Wireless Standards - IEEE 802.11n, IEEE 802.11g, IEEE 802.11b, Wireless Security - SSID Enable/Disable MAC Address Filter 64/128/152-bit WEP Encryption WPA/WPA2/WPA-PSK/WPA2-PSK (AES/TKIP) Encryption Wireless Modes - AP Mode, Multi-SSID Mode, Client Mode, Repeater Mode (WDS / Universal ), Bridge Mode, TPlink/Cisco/Netgear

SITC OF EPABX WITH 152 LINE EXTENSION UP TO 20 LINE WITH 4 SLT/ 2 CONSOLE (Panasonic / Simens / Matrix) 15-Party Conference, Universal Gateway, Mobile Remote Maintenance, LAN & Ethernet Port Least Cost Routing,Auto Attendant,Ext.Music Port 04 PSTN TRK+ 02 DIGITAL PORT+ 152 Analouge Extn . (EXP TO 200 LINES) Max. TDM Ports: 240 Interface support: PRI/VOIP/GSM/E&M Trunk

Supply, installation, testing & commissioning of termination box for 50 pair EPABX system complete as required

SITC OF 20 Pair Krone telephone termination box

SITC OF 20 Pair 0.5 sqm telephone cable (RR Cable/ finolex/ Anchor) with pvc conduit 25mm dia

Supplying and drawing following pair,0.5 sqmm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface / recessed PVC conduit as required.

CCTV Network Camera Dome 4 MP (Brand - Hikvision / Bosch / Honeywell) Image Sensor - 1/3" Progressive Scan CMOS, Shutter Speed - 1/3s to 1/10,000 s, Lens - 2.7mm, 4mm, 6mm @ F2.0angle of view: 106°(2.7mm), 83°(4mm), 55.4°(6mm), Day &Night - IR cut filter with auto switch, White Balance - Automatic/Manual, Video Compression - H.264/MJPEG/H.264+, Max. Resolution - 2688×1520, Communication Interface - 1 RJ45 10M/100M Ethernet port, Base T

Display : Screen size – 42 inch or above(LG/Sony/Samsung/ Philips), Panel Technology IPS, Aspect Ratio 16:9, Native Resolution 1920 x 1080 (FHD), Brightness 350nit or Higher, Contrast ratio 1100:1 or Higher, Dynamic CR 500,000:1 or Higher, Viewing Angle (H x V) 178 X 178, Orientation Portrait & Landscape, Operation Temperature 0 ⁰C to 40 ⁰C, Safety UL, eUL , EMC FCC Class “A”, IP video input 16 Channel , 1-ch, RCA (2.0 Vp-p, 1KΩ) Two-way audio input, 100Mbps Incoming bandwidth, 80Mbps Outgoing bandwidth, 128 Remote connection, HDMI/VGA output : 1-ch, resolution : 1920 × 1080P /60Hz, 1600 × 1200 /60Hz, 1280 × 1024 /60Hz, 1280 × 720 /60Hz, 1024 × 768 /60Hz, Audio output 1-ch, RCA (Linear, 1kΩ), Live view / Playback resolution : 5MP/3MP/1080p/UXGA/720p/VGA/4CIF/DCIF/2CIF/CIF/QCIF, Capability 1 SATA interface for 1 HDD Unloaded, 1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface, 1 × USB 2.0 and 1 × USB 3.0, OEM Authorization Certification,

SITC of 8 port Unmanaged Network PoE Switch: 24 port PoE Switch with PoE standard of IEEE 802.3af , IEEE 802.3at, PoE port, Uplink ports (DS-3E0326P-E) (Approved Makes: Hikvision/ Honeywell/ Bosch)

Supplying and drawing of UTP 4 pair CAT 6 LAN cable in the existing surface/ recessed PVC conduit as required.

1 run of cable

SITC of 6TB Surveillance Hard Disk (ST6000VX0023) (Approved Makes: Hikvision/ Honeywell/ Bosch)

19" 6U Rack for Switches complete as required

Camera installation and Connectivity.

BASE PHONE CLI (PANASONIC / BEETAL) Landline Phone with Caller ID Facility Corded Phone Numerical Keypad 35 Call Logs3 Display Lines Disclaimer,Tone/Pulse Switchable Ring LED Indication Flash Pause Dynamic Change Over From Pulse Tone, 1 Year Manufacturer Warranty

Supplying and fixing Intelligent Addressable type multicriteria detector with base for use as heat or smoke or combined both with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd.

Supplying and fixing Intelligent Addressable type Heat detector with base with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd.

Sypplying and fixing Intelligent Addressable Manual Call Point having inbuilt short circuit isolator i/c testing and commissiong etc as reqd.

Addressable sounder with interface module, power supply for sonder and programmable by software having integrated short circuit isolator & having operating temperature -10⁰C to + 55⁰C

Analogue Addressable Control module with IP66 casing containing four relay outputs, each containing a potential-free DPDT contact with a fail-safe and in-built short circuit isolator The ambient temperature range shall be -20C to +60C.

Supplying and Laying of 2X1.5 Sq.mm.marked copper FRLS wire with 20mm dia.PVC conduit pipe ISI marked, Complete with all fittings viz. Tees, Bends, Junction Boxes, Clamps/ Supports etc.

Duel LED Response Indicator (LOCAL)

4"/4" JB for mounting of detectors & other accessories with necessary fittings

Supplying and fixing Outdoor Electronic Sounder with 4 distinct tone including 40W Speaker with required accessories as reqd.

Supplying of XLPE/PVC insulated Sheathed (Heavy Duty) armoured electric cable with aluminium conductor of 1.1 KV graded con. IS 1554 Part I upto date amendment etc as required of following size

95 sq. mm, 3.5 core

16 sq. mm, 4 core

ABC Powder Type (Stored Pressure) Fire Extinguisher, 4 kg. Capacity, ISI mark (IS:15683), squeeze grip valve, operating temperature (+5) degree Celcuis to (+55) dgree Celcuis for Class 3A Type of Fire Filled with MAP ABC Powder, Complete in all respect

CO2 Type Fire Extinguisher, 4.5 Kg Capacity, ISI Mark (IS:15683) squeeze grip valve, operating temperature (-30) deg Cel to (55) deg cel. For Class 13B type of Fire Fitted with 1 Mt. Hose & PVC Horn, Complete in all respect.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS:1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

25 mm dia

80 mm dia

100 mm dia

150 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

Single headed Gunmetal

Single headed Stainless steel

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required :

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Gunmetal

Stainless steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following asrequired.

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

Gunmetal

Stainless steel (Grade 304)

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.

Description of Work

Boundary

Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of al! rubbish with all leads and lifts.

Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed.

Close timbering over areas including strutting, shoring and packing, cavities (wherever required) etc. complete. (Measurement to be taken of the face area timbered):

Extra for every additional lift of 1.5m or part thereof in:

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead

Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l.

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level

1:1.5:3(1 Cement :1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

1:2:4 (1 Cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering, finishing and reinforcement-All work upto plinth level

Reinforced cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finishin and reinforcement.

Reinforced cement conrete work in beams,suspended floors, roofs having slope upto 15, landings,balconiec, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excludingthe cost of centring, shuttering, finishing and reinforement with 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size).

Add or deduct for providing richer or leaner mixes respectively at all floor levels.

Brick work with bricks of class designation 100A in foundations and plinth in :

Half brick masonry with bricks of class designation 100A in foundations and plinth in :

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level

Brick work with bricks of class designation 100A in foundations and plinth in

Providing (1:4) Brick work with fly ash bricks etc all complete jobs.

Cement mortar 1:6 (1 cement: 6 coarse sand)

Extra for Brick work in superstructure above plinth level upto floor V cum Cement mortar 1:6 (1 cement: 6 coarse sand )

Half brick masonry with bricks of class designation 100A in foundations and plinth in : Cement mortar 1:4 (1 cement: 4 coarse send). Extra for half Brick masonry in superstructure above pinth level uptofloor V level.

Centring and shuttering including strutting,propping etc. and removal of form for.

Foundations, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters. Butteresses, plinth and string courses etc.

Suspended floors, roots, landings, balcnies and access platform.

Lintels, beams, plinth bams, griders, bressumers and contilevers.

Columns,Pillars, Piers, Abutments, Posts and Struts

Stairs,(excluding landings) except spiral-staircaces

Weather shade,Chajjas, corbels etc. including edges

Lintels, beams, plinth bams, griders, bressumers and contilevers.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

Thermo-Mechanically Treated bars TMTC-500-8mm dia.

Thermo-Mechanically Treated bars TMTC-500-10mm dia.

Thermo-Mechanically Treated bars TMT Fe-500-I2mrn dia.

Thermo-Mechanically Treated bars TMT Fe-500-16 mrn dia.

Thermo-Mechanically Treated bars TMT Fe-500-20 mrn dia.

Thermo-Mechanically Treated bars TMT Fe-500-25 mrn dia.

12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of near cement

15 mm cement plaster 1:3 (1 cement: 3 coarse sand ) finished with a floating coat of neat cement on the rough side of single or half brick wall.

20 mm cement plaster (1:4) etc all complete jobs.

Extra for providing and mixing water proofing material etc all complete jobs.

15 mm cement plaster on rough side of single or half brick wall of mix.

1:4(1 cement: 4 coarse sand )

1:6 (1 cement: 6 coarse sand)

Cement plaster in course sand, 12 mm cement plaster

6 mm cement plaster to ceiling

Providing and laying vitrifed floor tiles in different sizes (thickness to be specified by the manufactruer) with water absorption's less than 0.08 % and conforming to IS : 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand ) including grouting the joint with white cement and matching pigments etc., complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles 400x400 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such as white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing 20mm thick mirror polished, machine cut for kitchen platforms, vanity counters facias and similar locatins of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement :4 coarse sand) with joints treated with white cement, mixe* with matching pigament-epoxy touch ups. including rubbing, curing etx. complete at all Ibevels.

Extra for providing edge moulding to 18 mm thick marble stone counters, Vanities etc. over item no. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in -charge.

metre

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen sink in kitchen platform, vanity counters and similar location in marble / granite/stone work including necessary holes for pillar taps etc. including rubbing and polisheg of cut edges etc. complete.

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade, 2 or more coat.

Applying one coat of cement primer of approved brand and manufacture on wall surface:

Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade

Finishing walls with Acrylic Smooth exterior paint of required shade :

Providing and laying in situ seven course water proofing treatment with APP (AtacticPolypropylene) modified Polymeric membrane over roof consisting of first coat of bitumen primer @ 0.40Kg per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 2.0mm thick of 3.00 Kg/sqm weight consisting of five layers prefabricated with centre core as 1 OOmicron HMHDPE film sandwitched on both sides with polymeric mix and the polymeric mix is protected on both side with 20micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 100 grouted with cement mortar 1:3 (1 cement: 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 ( 1 cement: 3 fine sand) and finished neat which shall be paid for separately

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal ofwooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-Charge.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished 12 mm cement plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

metre

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Coupler, 110mm

Single Tee withdoor, 110x110x110mm

Band 87.50, 110mm band

Shoe plain, 110mm shoe

Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing M.S. rivets of sizes in position.

Providing and fixing pressed steel door confirming IS code 4351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by . mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

metre

Steel work in built up tubular trusses including cutting, hoisting, fixing inapplying a priming coat of approved steel primer etc all complete jobs.

Providing and fixing 35mm thick factory mode laminated veneer lumber door shutter conforming to IS:14616 & TADS 15-2001 (part B),manufactured in factories by approved manufacturers, including black enamelled M.S.butt hinges with necessary screws as per directions of Engineer in charge and panelling with panels of:

Providing and fixing in position collapsible steel shutters with vertical channes 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T-tron 40x40x6 mm with 40 mm dia steel pulleys complete with bots.nuts locking arrangement stoppers handies including applying a priming coat of approved steel primer.

Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels)made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm)

P/F factory made door frame of PVC 48x40x1.5mm in white , grey or wooden finish

P/F factory made door shutter of PVC, 30mm thk Factory made shutters with styles, rails and panels of PVC extruded sections in white, grey or wooden finish

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :

Providing and fixing alluminium handles anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc. complete:

Providing and fixing bright finished brass 100 mm mortice latch and lock with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868)aluminium lever with necessary screws etc.completefBest make of approved quality

Providing and fixing alluminium sliding tower bolt anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with nuts and screws etc. complete:

Providing and fixing alluminium hanging floor door stopper anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc.complete:

Providing and fixing M.S. grills of requirement pattern in frames of windows etc. with M.S. flats, square or round bars etc.all complete

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.).

Applying priming coat:

Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade:

Extra for providing and mixing water prooding material in cement concrete work in the proportion recommended by the manufacturers.

Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. Clear depth and 250mm apron including cost of E/W. involved with 75mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base.the drain duly.plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l,

Making plinth protection 50mm thick of cement concrete (1:3:6) , 1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti-termites' treatrnent(including the cost of chemical emulsion

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.

Providing and fixing skirting with Pre-laminated (one side decorative and other side balancing lamination) flat pressed 3 layer or graded particle board (medium density) Grade I, Type II, IS :12823 marked, with necessary fixing arrangements and screws, including drilling necessaryholes for rawl plugs etc. and priming coat on unexposed surface complete

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), including ISI marked M.S.pressed butt hinges bright finished of required size with necessery screws, all complete as per directions of Engineer-in- Charge and panelling with panels of:

38 mm thick parquet (wood block) flooring of 1st class teak wood laid over 25 mm thick levelling layer of cement concrete 1:2:4(1cement:2 coarse sand:4 store aggregate 10 mm nominal size) to be paid separately coated with a thin layer of hot bitumen of hot bitumen (blown type) @ 2.45 kg per sqm. including fixing blocks in position After dipping in hot bitumen (blown type) up to half depth ,planed levelled smooth and finished complete .

Providing and fixing in position precast R.C.C. manhole cover and frame of required shape and approved quality.

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal\ size) as per standard design

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5 mm thick) wire of high tensile strength of 165 kg/ sq mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Providing and fixing soil, waste and vent pipes :

metre

Supplying and fixing C.I. cover without frame for manholes etc all complete job

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1:3:6(1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing of glass panes with glazing clips and special metal-sash putty of approved make complete including applying a priming coat of approved steel primer; excluding the cost of metal beading and other fitting except necessary hinges or pivots as required.

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm ngle iron and 3mm MS gusset plates at the junction and corners. all necessary fittings completejncluding applying a priming coat of approved steel primer.

Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400x200x200 mm (inside)with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.

Trenching in ordinary soil upto a depth of 60 cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge of / and manure before and after flooring trench with water (excluding cost of imported earth, sludge or manure)

Supplying and stacking of good earth at site including royalty but excluding carriage (earth measured in stacks will be reduced by 20 % for payment)

Supplying and stacking Sludge at site including royalty and

Supplying and stacking at site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment)

Rough dressing the trenched ground including breaking clods.

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.

Fine dressing of the ground

Spreading of sludge, dump manure and / or good earth in required thickness as per direction of Officer-in-charge (Cost of sludge, dump manure and / or good earth to be paid separately).

Mixing earth and sludge or manure in proportion specified or directed.

Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free form weeds and fit for moving including supplying good earth if needed.

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20 % 1 part of stacked volume of manure after reduction by 8 % ) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure sludge or extra good earth if needed to be paid for separately)

Holes 1.2 m dia. And 1.2 m deep.

Holes 60 cm dia And 60 cm deep

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8 :1 (8 parts of stacked volume of earth after reduction by 8% ) flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed, within a lead of 50 m lift upto 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Plantation of trees & Shrubs/ creeps.

Shrubs / Creeps

Providing and fixing white vitreous china water closet squatting pan (Indian type WC pan) with 100mm sand cast Iron P or S Trap, 10 litre low level PVC flushing cistern (of approved make) with fittings CI/MS brackets, 32 mm diameter flush pipe with fittings and clamps, over flow arrangement with specials and mosquito proof coupling of approved municipal design including painting of fittings and brackets, cutting and making good the walls and floors wherever required.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

Providing and fixing white vitreous china wash basin with C.I. / M.S. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required.

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Providing and fixing white vitreous china pedestal for wash basin

Providing and fixing 600 x 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers comelete.

Providing and fixing toilet paper holder:

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gms.

Providing and fixing soil, waste and vent pipes.

merter

Providing and fixing M.S. holder bat clamps of approved design to sand cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) including cost of cutting holes and making good the walls etc.

Providing and fixing plain bend of required degree.

Providing and fixing single equal plain junction of required degree with acesses door, insersion rubber washer 3mm thick, bolts and nuts complete.

Providing and fixing terminal guard.

Providing and fixing collar

Providing lead caulked joints to sand cast iron / centrifugallly cast (spun) iron pipes and fittings of diametre:

Providing and fixing M.S stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diametre.

Providing and fixing sand cast iron trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors.

Painting sand cast iron/centrifugally cast (spun) iron soil waste vent pipes and fittings with paint of any colour such as chocolate gray or buff etc. over a coat of primer (of approved quality) for new work.

merter

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

merter

merter

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for therma expansion.(SW)

Coupler

Single tee with door

Shoe plain

Providing and fixing G.I. pipe complete with G.I. fittings and clamps, including, cutting and making good the walls etc. (internal work)

15 mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40 mm dia nominal bore

Painting of exposed pipes with two or more coats of synthetic enamel paint of approved quality over a coat of red oxide zinc cromate primer including painting of legends in English with direction arrows.

15 mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40 mm dia nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

metre

metre

Providing and fixing brass stop cock of approved quality :

Making connection of G.I distribution branch with G.I main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete.

Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end).

Providing and fixing gun metal non-return valve of approved quality (screwed end).

Providing and placing on terrace (at all floor levels) polythylene water storage ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing PTMT grating of approved quality and colour.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy aluminium rod with L.P / H.P.H.D plastic ball.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS : 8931

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

Providing and fixing uplasticised PVC connection pipe with brass unions:

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms

Excavating trenches of required width for pipes, cables etc. Including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5M including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering, etc.And disposing of surplus excavated soil as directed within a lead of 50 m Hard/dense soil.

metre

Providing, laying Non pressure NP2 class (light duty) RCC Pipes with collars jointed with stiff mixture of cement mortar in the propoertion of 1:2 (1 cement : 2 fine sand) including testing and jointing etc complete.

metre

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Extra for depth for manholes

metre

metre

Boring /drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in IS : 2800 (part I), including collecting samples form different strata, preparing and submitting strata chart / bore log, including hire & running Charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-Charge, upto 90 metre depth below ground level, all type of soil.

metre

Boring / drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in IS : 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer - in-Charge, beyond 90 metre & upto 150 metre depth below ground level.

metre

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.

metre

metre

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

metre

Providing and fixing suitable size threated mild steel cap or spot welded plate to the top of bore well housing / Casting pipe, removable as per requirement, all complete for borewell of :

Providing and fixing M.S. clamp of required dia to the top of casing / housing pipe of tube well as per IS : 2800 (part I ), including necessary bots & nuts of required size complete.

Providing and fixing Ball plug / Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS : 2800 (Part I)

Gravel packing in tubewell construction in accordance with IS : 4097, including providing gravel fine / medium / coarse , in required grading & sizes as per actual requirement , all complete as per direction of Engineer - in-Charges.

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I ) and IS : 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by 'V' notch method or any approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory,i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

S/F/F 2 H.P. Cromption or any other apprioved make Motor and ISI make automatic starter mounted on a common wooden board etc. all complete job.

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc.as required

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc.as required.

Wiring for light/ power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 No 4 sq.mm. FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface /recessed PVC conduit as required.

2x2.5 Sq.mm +1x2.5 Sq.mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

4 x 10 sq.mm. +1 x 10 sq.mm. earth wire

2 X 16 sq. mm + 1 X 16 sq. mm earth wire

2 X 25 sq. mm + 1 X 25 sq. mm earth wire

Supplying and fixing PVC/G.I box of 200mm x 250mm x 60mm deep on surface or in recess with suitable size of phenolic laminated sheet cover in fornt including painting etc as required.

Supplying and fixing PVC/G.I box of 75mm x75mm x 50mm deep on surface or in recess with suitable size of phenolic laminated sheet cover in fornt including painting etc as required.

Supplying and fixing suitable GI Box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc. as required. (for power plug )

Supplying and fixing suitable size G.I Box with modular plate and cover in front on surface in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc., as required. (for light plugs to be used in non residential buildings )

Supplying and fixing modular type 2 pin telephone socke/ speaker outlet on the existing modular plate & box including making connection,excluding moduler plate etc. as required.

Supplying and drawing 2 pair 0.5 sq mm. FR PVC insulated copper conductor telephone cable through existing PVC concuit including connection, testing etc. as required.

Supplying and drawing low resistance co-axial T.V cable RJ-6 grade 0.7mm solid copper conductor PE insulated shielded with fine tinned copper braid and protected with PVC sheath in the existing PVC concuit etc. as required.

Supplying and fixing modular T.V antenna socket on the existing modular plate and metal box including making connection, etc. as required.

Supply fitting fixing of electronic musicle call bell suitable for single phase 230 volts, complete etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & box excluding moduler plate etc. as required.

Supplaying and fixing 2 pin 5a celling rose on the existing junction box/PVC box including connection etc.as required.

Supplying & fixing brass batten/angle holder including connection etc. as required.

Supply & fixing 2+ 8 way double door SP & N, sheet steel, MCB distribution board, 240 volts, on surface/ in recess, complete with tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc.as required (But without MCB / RCCB / Isolator) Lighting DB

Supply & fixing 4 way(4+12) double door TP & N, sheet steel, MCB distribution board, 415 volts, on surface/ in recess, complete with tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc.as required (But without MCB / RCCB / Isolator) Power DB

Supply and fixing following rating and capacity 4 pole MCCB in existing panel board. Including drilling hole in cubical panel, making connection etc.as required.

P/F following capacity busbar chamber with 4 strips of suitable size made of copper, heavy duty complete with all accessories including connections, earthing the body etc. as reqd.

Supply and fixing 200 A 4 Pole on load / panel moumted change over switch in existing cubical panel board making connection, earthing the body etc.as required

Supplay and fixing wall /floor mounted cubicle panel board fabricated with 16 gauge iron sheet suitable for panel mounted switch discconnector including Bus bar chamber insulator and painting etc as required.9but without bus bar copper strip)

S/F digital voltmeter three phase existing cubicle panel board including drilling holes in the panel board making connection etc.

S/F digital ammeter three phase existing cubicle panel board including drilling holes in the panel board making connection etc.

Supply and Installation of regular/standard module AC ceiling fan of 1200 mm sweep including wiring the down rod of standard length 9 upto 30 cm ) with 1.5 sq mm FR pvc insulated copper conductor etc as required.

Supply and Installation of 300 mm 230 volt AC exhaust fan in the existing opening including making good the damage connection testing commissioning etc as required.

Supplying and fixing single wall mounted 20/22 watt LED type batten fitting complete with electronic driver and LED tube etc directly on wall/ ceiling including connections with 1.5 sq.mm FR PVC insulated copper conductor and earthing the body etc. as required.

Supply and fixing Bulk Head Fitting die cast aluminium alloy body with prismatic glass cover suitable for the GLS / CFL L , directly on wall / ceilling including connection etc. as required.

Supplying and fixing indoor recess mounting 36 watt LED flat panel luminaire suitable for armstrong / grid ceiling and complete with electronic driver etc. irectly on false ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supplying and fixing single wall mounted 18/22 watt LED type batten fitting complete with electronic driver and LED tube etc directly on wall/ ceiling including connections with 1.5 sq.mm FR PVC insulated copper conductor and earthing the body etc. as required.

Supplying and fixing 40/45 watt LED type street light with die cast aluminium housing for ingress protection of IP65 and complete with all accessories etc, on pole/building including connection with FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supply and erection of 6 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 130 mm, made of 3 mm thick sheet along with base plate of size 220 X 220 X 12 mm , small door opening for junction box mounting with MCB & connector, cement concrete of 1:3:6 including excavation, refilling and suitable size foundation bolts with template and all complete job as required. (but without pole collar)

Providing chemical/mineral maintenance free earthing system comprising of copper coated earth electrode 3 metre length and 17.2 mm outer dia along with 25 kg earth conductivity enhancing back fill mineral compound for earth electrode to fill up the excavated earth and earth inspection pit etc. as required. Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc. as required. Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing etc. as required.

Providing and fixing 4.00 mm dia.copper wire on surface or in recess for loop earthing as required.

P/F 25mm x 5mm G.I. Strip on surface or in recess for connections etc as required.

P/F lightning conductor final, made of 25mm dia. 300mm long, copper tube having single pron on top with 85 mm dia 3 mm thick copper base palte including holes etc complete as required.

P/F copper tape 20mmx3mm thick on parapet or surface of wall for lighting conductor complete as required ( for horizontal run)

P/F copper tape 20mmx3mm thick on parapet or surface of wall for lighting conductor complete as required ( for vertical run)

P/F testing joint, made of 20mm x 3mm thick copper Strip.125 mm long with 4 nos of tinned brass bolts nuts chuk nuts and spring washer etc complete as required.

Providing and fixing earth bus of 50 mm x 5 mm copper strip on surface for connections etc. as required.

Supplying of XLPE/PVC insulated Sheathed (Heavy Duty) armoured electric cable with aluminium conductor of 1.1 KV graded con. IS 1554 Part I upto date amendment etc as required of following size

metre

Laying of one number PVC insulated and pvc sheathed /XLPE power cable of 1.1 kv grade of following size direct in ground including excavation sand cushioning protective covering and refiling the trench etc as required.

metre

ABC Powder Type (Stored Pressure) Fire Extinguisher, 4 kg. Capacity, ISI mark (IS:15683), squeeze grip valve, operating temperature (+5) degree Celcuis to (+55) dgree Celcuis for Class 3A Type of Fire Filled with MAP ABC Powder, Complete in all respect

CO2 Type Fire Extinguisher, 4.5 Kg Capacity, ISI Mark (IS:15683) squeeze grip valve, operating temperature (-30) deg Cel to (55) deg cel. For Class 13B type of Fire Fitted with 1 Mt. Hose & PVC Horn, Complete in all respect.

SITC of 1.5 Ton 5 Star Inverter Split AC copper coil . with Stablizer (NOTE:- Air Conditioning System and its accessories should note have Made in CHINA or Any CHINEASE accesories ) Make must be of Would Class Standard. (HITACHI/DAIKIN/TOSHIBA/MITSUBISI/O General or Eqvt )

SITC of 1.0 Ton 5 Star Inverter Split AC copper coil with Stablizer . (NOTE:- Air Conditioning System and its accessories should note have Made in CHINA or CHINEASE accesories ) Make must be Would Class Standard. (HITACHI/DAIKIN/TOSHIBA/MITSUBISI/O General or Eqvt)

Extra copper pipe

Extra Drain Pipe

Supplying, installation, testing and Commissioning of passenger Car Type Elevator (lifts) 8/544 Kg-1 MPS (for FOUR stop, G+3 One No. lift) with fan, fully automatic state of the art technologies, make from World Fame manufactures (Make:- Thyssen OTIS/ MITSUBISI/ SCHINDLER or Eqvt with all complete job .

CCTV Network Camera Dome 4 MP (Brand - Hikvision / Bosch / Honeywell) Image Sensor - 1/3" Progressive Scan CMOS, Shutter Speed - 1/3s to 1/10,000 s, Lens - 2.7mm, 4mm, 6mm @ F2.0angle of view: 106°(2.7mm), 83°(4mm), 55.4°(6mm), Day &Night - IR cut filter with auto switch, White Balance - Automatic/Manual, Video Compression - H.264/MJPEG/H.264+, Max. Resolution - 2688×1520, Communication Interface - 1 RJ45 10M/100M Ethernet port, Base T

CCTV Network Camera Bullet 4 MP (Brand - Hikvision / Bosch / Honeywell) Image Sensor - 1/3" Progressive Scan CMOS, Shutter Speed - 1/3s to 1/10,000 s, Lens - 2.7mm, 4mm, 6mm @ F2.0angle of view: 106°(2.7mm), 83°(4mm), 55.4°(6mm), Day &Night - IR cut filter with auto switch, White Balance - Automatic/Manual, Video Compression - H.264/MJPEG/H.264+, Max. Resolution - 2688×1520, Communication Interface - 1 RJ45 10M/100M Ethernet port, Base T

Network Vedio Recorder up to 32 network Camera (Brand - Hikvision / Bosch / Honeywell) Dual-OS design to ensure high reliability of system running, ANR technology to enhance the storage reliabilitywhen the network is disconnected, H.265/H.264/H.264+video formats , Connectable to the third-party network cameras, Recording at up to 8 MP resolution, Supports live view, storage, and playback of the connected camera at up to 8MP resolution ,HDMI/VGA outputs provided, HDMI Videooutput at up to 4K (3840 ×2160)resolution, 4 SATA interfaceconnectable for recording and backup, Storage space effectively saved by 50% to 70% with the use of H.264+ decoding format, Incoming bandwidth - 80 MBPS, Outgoing bandwidth - 80 MBPS, Network protocols - TCP/IP, DHCP, HIK Cloud P2P, DNS, DDNS, NTP, SADP, SMTP, NFS, iSCSI, UPnP™, HTTPS

Network Switch 24 Port PoE with 2 SFP Ports (Brand - Netgear / Aruba/ HP) Network Ports - (24) 10/100/1000Mbps autosensing + 2 Gigabit SFP uplinks, Network Protocol and Standards Compatibility - IEEE 802.3i 10BASE-T• IEEE 802.3u 100BASE-TX• IEEE 802.3ab 1000BASE-T• IEEE 802.3z 1000BASE-X• IEEE 802.3x full-duplex flow control•,Power consumption: 59.3W maximum, Administrative Switch Management - IEEE 802.1Q static VLAN (64 groups, static)• Protected ports• IEEE 802.1p Class of Service (CoS)• Port-based QoS• DSCP-based QoS• DiffServ• IEEE 802.3ad Link Aggregation (manual or LACP)• IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)• IEEE 802.1ab Link Layer Discovery Protocol (LLDP)• LLDP-MED• SNMP v1, v2c, v3• RFC 1213 MIB II• RFC 1643 Ethernet Interface MIB• RFC 1493 Bridge MIB• RMON group 1, 2, 3, 9• Auto voice VLAN• DHCP Filtering• HTTP and HTTPS• Ping and traceroute• Power saving when link down• DHCP filtering• IEEE 802.1x (MD5) with Guest VLAN• Jumbo frame support• Port-based security by locked MAC addresses• MAC and IP-based ACL• SNTP• Port mirroring support (many-to-one)• Web-based configuration• Configuration backup/restore• Password access control• Firmware upgradeable• PoE (46 Watts of power budget)

Category 6, UTP 24-Port Patch Panel Size - 482.6mm x 44.2 (19’’ x 1U), Panel Material - Steel-fully powder coated, Unshielded - RJ 45, Plug Insertion Cycle - 750 times DC Resistance- 72Ω max, Voltage Rating - 72 Vdc max, Current Rating - 1.5A max

Category 6 UTP Patch Cords - 1 Mtr Standard Colour - Blue, Grey, Yellow, RJ45 Plug - Polycarbonate plug, Current Rating - 1.5A max, Insulation Resistance - 500MΩ/km(min)@500 Vdc, Contact Resistance - 15 mΩ (max) per contact

Hard disk 6 TB

19 U Network Rack (Brand - Valrack / Netrack / Legrand)

CAT 6 Cable for CCTV camera (Brand - Digilink / Legrand / Molex)

Cable laying with PVC conduit ISO Certified

CCTV installaiton configuration & testing

32" Full HD LED Display for CCTV

25 mm dia.

meter

80 mm dia.

100mm dia

150 mm dia (IS : 1239)-Class-C

Providing & Fixing standard Fireman AXE with heavy insulated rubber handle.

Providing and fixing cast iron dual plate wafer type non return valves of PN1.6 including nuts, bolts,1.5mm thick compressed asbestos gasket including matching flanges as per table "E" complete

Providing and fixing C.I. butterfly valves PN 1.6 complete with bolts, nuts 1.5mm thick compressed asbestos gasket companion flanges as per table "E" complete.

150 mm dia with lever

100 mm dia with lever

80 mm dia. With lever

Providing and fixing dial type pressure gauge with isolation cock and copper pipe at hydrant station.

Dial diameter 100 mm calibration 0-15 kg/ sq.cm.

Providing and fixing gunmetal single acting air release valve with screwed inlet 25 mm dia..

Providing & fixing of Foot Valve in underground water tank.

Providing and fixing SS316 Single headed landing valve conforming to IS -5290 (Type-A) with 63 mm dia. single instantaneous female coupling on the outlet SS316 metal blank cap and chain, necessary companion flanges, nuts, bolts, washer and gasket complete as per specification. (ISI marked). All parts and body shall be of SS316 as per IS:5290.

Providing and fixing first aid fire hose reel drum wall mounting, swinging type(Powder coated finish in fire red) fitted with 20 mm dia. 30 m long high pressure hose(IS:444, Type-2) with 5 mm outlet SS nozzle with shut off valve (IS:8090). complete hose reel drum shall be conforming to IS:884)

Providing and fixing RRL Hose Pipe 63 mm dia. 15m long rubberized lined hose including SS316 male and female instantaneous type coupling approved by fire authority, machine wound with copper wire complete in all respects. Hose shall conform to IS 636 Type-A and coupling to IS 903 -1975 ( ISI marked)

Providing and fixing standard short size SS316 branch pipe with gunmetal nozzle 16 mm dia. outlet with standard instantaneous type 63 mm dia. coupling. (ISI marked, IS:903)

Supply, Installation, Testing & Commissioning of 100 mm dia Three - Way fire brigade inlet connection of 63 mm size instantaneously make coupling and shall be protected with plastic cap & chain etc. complete with one 100 mm dia sluice valve and 100 mm dia non-return valve ( To be connected to external ring main / wet riser / sprinkler riser ). Make : KALPEX / NEW - TECH.

Supplying and fixing of hose cabinel of sjze 900 mm x 600 mm x 500 mm of 2 mm thick MS sheet with 6mm thick glazed glass doors with necessary locking 'arrangement suitable to accommodation external hydrant with bulterfly valve 2 No's and 15mtr Long Hose pipe, 1 No. branch pipe mounted on wall OR raised brick Plateform duly Painted with post office red externally and white internally with.synthetic enamel paint complete in all respact for exlernai hydrant as required.

Supply of electric driven automatic fire Pump suitable for automatic operation consisting of the following:Horizontal end suction centrifugal pump complete with mechanical seal and including necessary arrangement for testing of pump.Squirrel cage induction motor suitable for 415 V, 50 Hz, AC supply of suitable rating for the above pump with synchronous speed of 2900 RPM T.E.F.C. type and conforming to IP:55 and flexible coupling and coupling guard with the pump.Common bed plate of fabricated mild steel channel or cast iron type.Suitable reinforced cement concrete pump foundation including cushy foot mounting, foundation bolts, washers as required.

Providing and fixing air vessel for fire pumps as per following specifications:

Providing and fixing dust and vermin proof motor control panel fabricated from 14 SWG MS sheet with stove enamelled paint and comprising of: (for Fire Booste pump).

Supply, installation, testing & commissioning of electric driven Jockey Pump suitable for automatic operation consisting of the following:Horizontally mounted centrifugal end suction pump complete with mechanical seal and including necessary arrangement for testing of pump with Squirrel cage induction motor suitable for 415 V, 50 Hz, AC supply of suitable rating for the above pump with synchronous speed of 2900 RPM T.E.F.C. type and conforming to IP:55 and flexible coupling and coupling guard with the pump.

Water coolled Diesel Engine developing suitable BHP at 1500 RPM for the Pump, common bed plate for mounting of engine and pump, RCC foundation and vibration damping arrangement by Cushy Foot and engine panel provided by engine manufacturer, connection to Engine Starting Panel as per item (4), sealed maintenance free batteries of 24 V, 88 AH. Rate shall include Exhaust pipe of required length with asbestos lagging, muffler, day oil tank of 400 lts with first charge and manual oil pump set.

XLPE/PVC insulated PVC sheathed (Heavy duty) armoured electric cable with aluminium conductor.

meter

meter

32 bit microprocessor based Intelligent Addressable Fire Alarm Control panel with 2 loops with battery back up. The panel would be modular, decentralized, with The panel shall be consisting with minimum 240 character LCD display and for networking. The Panel would be able to record atleast 60,000 events history. Each loop would be capable to have atleast 250 addressable detectors and addressable devices with up to 3.5km loop length. Make: Schrack Seconet (Vds approved)

1 KVA LINE INTERACTIVE UPS WITH 30 MIN BATTERY BACK UP

Supplying and fixing Intelligent Addressable type multicriteria detector with base for use as heat or smoke or combined both with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd.

Supplying and fixing Intelligent Addressable type Heat detector with base with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd.

Sypplying and fixing Intelligent Addressable Manual Call Point having inbuilt short circuit isolator i/c testing and commissiong etc as reqd.

Addressable sounder with interface module, power supply for sonder and programmable by software having integrated short circuit isolator & having operating temperature -10⁰C to + 55⁰C

Analogue Addressable Control module with IP66 casing containing four relay outputs, Each containing a potential-free DPDT contact with a fail-safe and in-built short circuit isolator The ambient temperature range shall be -20C to +60C.

4"/4" JB for mounting of detectors & other accessories with necessary fittings

Supplying and fixing Outdoor Electronic Sounder with 4 distinct tone including 40W Speaker with required accessories as reqd.

Supplying and laying of 2x1.5 sq.mm. ISI marked copper armourd conductor cable with gland scoket and other wiring accessories on the existing surface/tray/shaft etc as reqd

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia wire and 1.4 mm wide aperture with matching wood beading

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners.all necessary fittings completejncluding applying a priming coat of approved steel primer.

Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed protions of W.C. kitchen and the like consisting of :

Providing and laying integral cement based water proofing treatment including prepatation of surface as required for treatment of roofs, balconies , terraces etc, consisting of following operations. (a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water -proofing compound cleaning the surface before treatment, (b) Laying cement concrete using broken bricks / brick bats 25 mm to 100 mm size with 50 % of cement mortar 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 over 20 mm thick layer of cement mortar of mix 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water froofing compound conforming to IS 2545 to reuired slope and treating similary the adjoining walls upto 300 mm height including rounding of junctions, or walls ad slabs. (c) After two days of proper curing

Cement concrete flooring 1:2:4(1 cement:2 coarse:sand:4 graded stone agregate) finished with a floating coat of neat cement including cement slurry, etc. but excluding the cost of nosing of steps etc. complete

Cement plaster skirting (upto 30 cm hieght) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement

Increase

Less 16.61 % below as per agreement

Description of Work

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia wire and 1.4 mm wide aperture with matching wood beading

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners.all necessary fittings completejncluding applying a priming coat of approved steel primer.

Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed protions of W.C. kitchen and the like consisting of :

Providing and laying integral cement based water proofing treatment including prepatation of surface as required for treatment of roofs, balconies , terraces etc, consisting of following operations. (a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water -proofing compound cleaning the surface before treatment, (b) Laying cement concrete using broken bricks / brick bats 25 mm to 100 mm size with 50 % of cement mortar 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 over 20 mm thick layer of cement mortar of mix 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water froofing compound conforming to IS 2545 to reuired slope and treating similary the adjoining walls upto 300 mm height including rounding of junctions, or walls ad slabs. (c) After two days of proper curing

Cement concrete flooring 1:2:4(1 cement:2 coarse:sand:4 graded stone agregate) finished with a floating coat of neat cement including cement slurry, etc. but excluding the cost of nosing of steps etc. complete

Cement plaster skirting (upto 30 cm hieght) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement

Description of Work

Amount (Rs.)

Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of al! rubbish with all leads and lifts.

Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed.

Close timbering over areas including strutting, shoring and packing, cavities (wherever required) etc. complete. (Measurement to be taken of the face area timbered):

Extra for every additional lift of 1.5m or part thereof in:

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead

Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l.

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level

1:1.5:3(1 Cement :1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

1:2:4 (1 Cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering, finishing and reinforcement-All work upto plinth level

Reinforced cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finishin and reinforcement.

Reinforced cement conrete work in beams,suspended floors, roofs having slope upto 15, landings,balconiec, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excludingthe cost of centring, shuttering, finishing and reinforement with 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size).

Add or deduct for providing richer or leaner mixes respectively at all floor levels.

Brick work with bricks of class designation 100A in foundations and plinth in :

Half brick masonry with bricks of class designation 100A in foundations and plinth in :

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level

Brick work with bricks of class designation 100A in foundations and plinth in

Providing (1:4) Brick work with fly ash bricks etc all complete jobs.

Cement mortar 1:6 (1 cement: 6 coarse sand)

Extra for Brick work in superstructure above plinth level upto floor V cum Cement mortar 1:6 (1 cement: 6 coarse sand )

Half brick masonry with bricks of class designation 100A in foundations and plinth in : Cement mortar 1:4 (1 cement: 4 coarse send). Extra for half Brick masonry in superstructure above pinth level uptofloor V level.

Centring and shuttering including strutting,propping etc. and removal of form for.

Foundations, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters. Butteresses, plinth and string courses etc.

Suspended floors, roots, landings, balcnies and access platform.

Lintels, beams, plinth bams, griders, bressumers and contilevers.

Columns,Pillars, Piers, Abutments, Posts and Struts

Stairs,(excluding landings) except spiral-staircaces

Weather shade,Chajjas, corbels etc. including edges

Lintels, beams, plinth bams, griders, bressumers and contilevers.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

Thermo-Mechanically Treated bars TMTC-500-8mm dia.

Thermo-Mechanically Treated bars TMTC-500-10mm dia.

Thermo-Mechanically Treated bars TMT Fe-500-I2mrn dia.

Thermo-Mechanically Treated bars TMT Fe-500-16 mrn dia.

Thermo-Mechanically Treated bars TMT Fe-500-20 mrn dia.

Thermo-Mechanically Treated bars TMT Fe-500-25 mrn dia.

12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of near cement

15 mm cement plaster 1:3 (1 cement: 3 coarse sand ) finished with a floating coat of neat cement on the rough side of single or half brick wall.

20 mm cement plaster (1:4) etc all complete jobs.

Extra for providing and mixing water proofing material etc all complete jobs.

15 mm cement plaster on rough side of single or half brick wall of mix.

1:4(1 cement: 4 coarse sand )

1:6 (1 cement: 6 coarse sand)

Cement plaster in course sand, 12 mm cement plaster

6 mm cement plaster to ceiling

Providing and laying vitrifed floor tiles in different sizes (thickness to be specified by the manufactruer) with water absorption's less than 0.08 % and conforming to IS : 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand ) including grouting the joint with white cement and matching pigments etc., complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles 400x400 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such as white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing 20mm thick mirror polished, machine cut for kitchen platforms, vanity counters facias and similar locatins of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement :4 coarse sand) with joints treated with white cement, mixe* with matching pigament-epoxy touch ups. including rubbing, curing etx. complete at all Ibevels.

Extra for providing edge moulding to 18 mm thick marble stone counters, Vanities etc. over item no. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in -charge.

metre

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen sink in kitchen platform, vanity counters and similar location in marble / granite/stone work including necessary holes for pillar taps etc. including rubbing and polisheg of cut edges etc. complete.

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade, 2 or more coat.

Applying one coat of cement primer of approved brand and manufacture on wall surface:

Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade

Finishing walls with Acrylic Smooth exterior paint of required shade :

Providing and laying in situ seven course water proofing treatment with APP (AtacticPolypropylene) modified Polymeric membrane over roof consisting of first coat of bitumen primer @ 0.40Kg per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 2.0mm thick of 3.00 Kg/sqm weight consisting of five layers prefabricated with centre core as 1 OOmicron HMHDPE film sandwitched on both sides with polymeric mix and the polymeric mix is protected on both side with 20micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 100 grouted with cement mortar 1:3 (1 cement: 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 ( 1 cement: 3 fine sand) and finished neat which shall be paid for separately

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal ofwooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-Charge.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished 12 mm cement plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

metre

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Coupler, 110mm

Single Tee withdoor, 110x110x110mm

Band 87.50, 110mm band

Shoe plain, 110mm shoe

Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing M.S. rivets of sizes in position.

Providing and fixing pressed steel door confirming IS code 4351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by . mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

metre

Steel work in built up tubular trusses including cutting, hoisting, fixing inapplying a priming coat of approved steel primer etc all complete jobs.

Providing and fixing 35mm thick factory mode laminated veneer lumber door shutter conforming to IS:14616 & TADS 15-2001 (part B),manufactured in factories by approved manufacturers, including black enamelled M.S.butt hinges with necessary screws as per directions of Engineer in charge and panelling with panels of:

Providing and fixing in position collapsible steel shutters with vertical channes 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T-tron 40x40x6 mm with 40 mm dia steel pulleys complete with bots.nuts locking arrangement stoppers handies including applying a priming coat of approved steel primer.

Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels)made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm)

P/F factory made door frame of PVC 48x40x1.5mm in white , grey or wooden finish

P/F factory made door shutter of PVC, 30mm thk Factory made shutters with styles, rails and panels of PVC extruded sections in white, grey or wooden finish

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :

Providing and fixing alluminium handles anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc. complete:

Providing and fixing bright finished brass 100 mm mortice latch and lock with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868)aluminium lever with necessary screws etc.completefBest make of approved quality

Providing and fixing alluminium sliding tower bolt anodised(anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with nuts and screws etc. complete:

Providing and fixing alluminium hanging floor door stopper anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc.complete:

Providing and fixing M.S. grills of requirement pattern in frames of windows etc. with M.S. flats, square or round bars etc.all complete

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.).

Applying priming coat:

Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade:

Extra for providing and mixing water prooding material in cement concrete work in the proportion recommended by the manufacturers.

Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. Clear depth and 250mm apron including cost of E/W. involved with 75mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base.the drain duly.plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l,

Making plinth protection 50mm thick of cement concrete (1:3:6) , 1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti-termites' treatrnent(including the cost of chemical emulsion

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.

Providing and fixing skirting with Pre-laminated (one side decorative and other side balancing lamination) flat pressed 3 layer or graded particle board (medium density) Grade I, Type II, IS :12823 marked, with necessary fixing arrangements and screws, including drilling necessaryholes for rawl plugs etc. and priming coat on unexposed surface complete

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), including ISI marked M.S.pressed butt hinges bright finished of required size with necessery screws, all complete as per directions of Engineer-in- Charge and panelling with panels of:

38 mm thick parquet (wood block) flooring of 1st class teak wood laid over 25 mm thick levelling layer of cement concrete 1:2:4(1cement:2 coarse sand:4 store aggregate 10 mm nominal size) to be paid separately coated with a thin layer of hot bitumen of hot bitumen (blown type) @ 2.45 kg per sqm. including fixing blocks in position After dipping in hot bitumen (blown type) up to half depth ,planed levelled smooth and finished complete .

Providing and fixing in position precast R.C.C. manhole cover and frame of required shape and approved quality.

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal\ size) as per standard design

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5 mm thick) wire of high tensile strength of 165 kg/ sq mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Providing and fixing soil, waste and vent pipes :

metre

Supplying and fixing C.I. cover without frame for manholes etc all complete job

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1:3:6(1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing of glass panes with glazing clips and special metal-sash putty of approved make complete including applying a priming coat of approved steel primer; excluding the cost of metal beading and other fitting except necessary hinges or pivots as required.

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm ngle iron and 3mm MS gusset plates at the junction and corners. all necessary fittings completejncluding applying a priming coat of approved steel primer.

Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400x200x200 mm (inside)with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.

Trenching in ordinary soil upto a depth of 60 cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge of / and manure before and after flooring trench with water (excluding cost of imported earth, sludge or manure)

Supplying and stacking of good earth at site including royalty but excluding carriage (earth measured in stacks will be reduced by 20 % for payment)

Supplying and stacking Sludge at site including royalty and

Supplying and stacking at site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment)

Rough dressing the trenched ground including breaking clods.

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.

Fine dressing of the ground

Spreading of sludge, dump manure and / or good earth in required thickness as per direction of Officer-in-charge (Cost of sludge, dump manure and / or good earth to be paid separately).

Mixing earth and sludge or manure in proportion specified or directed.

Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free form weeds and fit for moving including supplying good earth if needed.

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20 % 1 part of stacked volume of manure after reduction by 8 % ) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure sludge or extra good earth if needed to be paid for separately)

Holes 1.2 m dia. And 1.2 m deep.

Holes 60 cm dia And 60 cm deep

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8 :1 (8 parts of stacked volume of earth after reduction by 8% ) flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed, within a lead of 50 m lift upto 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Plantation of trees & Shrubs/ creeps.

Shrubs / Creeps

Providing and fixing white vitreous china water closet squatting pan (Indian type WC pan) with 100mm sand cast Iron P or S Trap, 10 litre low level PVC flushing cistern (of approved make) with fittings CI/MS brackets, 32 mm diameter flush pipe with fittings and clamps, over flow arrangement with specials and mosquito proof coupling of approved municipal design including painting of fittings and brackets, cutting and making good the walls and floors wherever required.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required

Providing and fixing white vitreous china wash basin with C.I. / M.S. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required.

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Providing and fixing white vitreous china pedestal for wash basin

Providing and fixing 600 x 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers comelete.

Providing and fixing toilet paper holder:

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gms.

Providing and fixing soil, waste and vent pipes.

merter

Providing and fixing M.S. holder bat clamps of approved design to sand cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) including cost of cutting holes and making good the walls etc.

Providing and fixing plain bend of required degree.

Providing and fixing single equal plain junction of required degree with acesses door, insersion rubber washer 3mm thick, bolts and nuts complete.

Providing and fixing terminal guard.

Providing and fixing collar

Providing lead caulked joints to sand cast iron / centrifugallly cast (spun) iron pipes and fittings of diametre:

Providing and fixing M.S stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diametre.

Providing and fixing sand cast iron trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors.

Painting sand cast iron/centrifugally cast (spun) iron soil waste vent pipes and fittings with paint of any colour such as chocolate gray or buff etc. over a coat of primer (of approved quality) for new work.

merter

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

merter

merter

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for therma expansion.(SW)

Coupler

Single tee with door

Shoe plain

Providing and fixing G.I. pipe complete with G.I. fittings and clamps, including, cutting and making good the walls etc. (internal work)

15 mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40 mm dia nominal bore

Painting of exposed pipes with two or more coats of synthetic enamel paint of approved quality over a coat of red oxide zinc cromate primer including painting of legends in English with direction arrows.

15 mm dia nominal bore

20mm dia nominal bore

25mm dia nominal bore

32mm dia nominal bore

40 mm dia nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

metre

metre

Providing and fixing brass stop cock of approved quality :

Making connection of G.I distribution branch with G.I main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete.

Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end).

Providing and fixing gun metal non-return valve of approved quality (screwed end).

Providing and placing on terrace (at all floor levels) polythylene water storage ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing PTMT grating of approved quality and colour.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy aluminium rod with L.P / H.P.H.D plastic ball.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS : 8931

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

Providing and fixing uplasticised PVC connection pipe with brass unions:

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms

Excavating trenches of required width for pipes, cables etc. Including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5M including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering, etc.And disposing of surplus excavated soil as directed within a lead of 50 m Hard/dense soil.

metre

Providing, laying Non pressure NP2 class (light duty) RCC Pipes with collars jointed with stiff mixture of cement mortar in the propoertion of 1:2 (1 cement : 2 fine sand) including testing and jointing etc complete.

metre

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Extra for depth for manholes

metre

metre

Boring /drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in IS : 2800 (part I), including collecting samples form different strata, preparing and submitting strata chart / bore log, including hire & running Charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-Charge, upto 90 metre depth below ground level, all type of soil.

metre

Boring / drilling bore well of required dia for casing / strainer pipe, by suitable method prescribed in IS : 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart / bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer - in-Charge, beyond 90 metre & upto 150 metre depth below ground level.

metre

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.

metre

metre

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

metre

Providing and fixing suitable size threated mild steel cap or spot welded plate to the top of bore well housing / Casting pipe, removable as per requirement, all complete for borewell of :

Providing and fixing M.S. clamp of required dia to the top of casing / housing pipe of tube well as per IS : 2800 (part I ), including necessary bots & nuts of required size complete.

Providing and fixing Ball plug / Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS : 2800 (Part I)

Gravel packing in tubewell construction in accordance with IS : 4097, including providing gravel fine / medium / coarse , in required grading & sizes as per actual requirement , all complete as per direction of Engineer - in-Charges.

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I ) and IS : 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by 'V' notch method or any approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory,i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

S/F/F 2 H.P. Cromption or any other apprioved make Motor and ISI make automatic starter mounted on a common wooden board etc. all complete job.

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc.as required

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc.as required.

Wiring for light/ power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 No 4 sq.mm. FR PVC insulated copper conductor single core cable for loop earthing as required.