Implementation of Singua FIS Cluster under MCAD _Phase-I_ for the year 2025-26_ under Boko_Chaygaon_Chamaria Division Irrigation Boko

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) R.C.C. column, R.C.C. Wall, R.C.C. Slab, R.C.C. Beam, R.C.C. Corbel

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in super structure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) : With Modular bricks

Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to window frames etc. including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete.

40 mm thick marble chips flooring rubbed and polished to granolithic finish, under layer 34 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) and top layer 6mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from 1 mm to 4 mm nominal size, laid in cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion of 4:7 (4 cement marble powder mix : 7 marble chips) by volume, including cement slurry etc. complete : Dark shade pigment with ordinary cement

External plaster 12 mm cement plaster of mix 1:4 (1 cement: 4 fine sand)

Internal plaster 20 mm cement plaster of mix 1:4 (1 cement: 4 fine sand)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Block board construction flush door with commercial ply on both faces 35 mm thick

Ventilator

Gantry Girder (5T)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) R.C.C. column, R.C.C. Wall, R.C.C. Slab, R.C.C. Beam, R.C.C. Corbel

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in super structure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) : With Modular bricks

Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to window frames etc. including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete.

40 mm thick marble chips flooring rubbed and polished to granolithic finish, under layer 34 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) and top layer 6mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from 1 mm to 4 mm nominal size, laid in cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion of 4:7 (4 cement marble powder mix : 7 marble chips) by volume, including cement slurry etc. complete : Dark shade pigment with ordinary cement

External plaster 12 mm cement plaster of mix 1:4 (1 cement: 4 fine sand)

Internal plaster 20 mm cement plaster of mix 1:4 (1 cement: 4 fine sand)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Block board construction flush door with commercial ply on both faces 35 mm thick

Ventilator

Gantry Girder (5T)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in super structure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) : With Modular bricks

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

40 mm thick marble chips flooring rubbed and polished to granolithic finish, under layer 34 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) and top layer 6mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from 1 mm to 4 mm nominal size, laid in cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion of 4:7 (4 cement marble powder mix : 7 marble chips) by volume, including cement slurry etc. complete : Dark shade pigment with ordinary cement

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 20 mm cement plaster

CEMENT PLASTER (IN FINE SAND) 20 mm cement plaster of mix :1:4 (1 cement: 4 fine sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces : Two coats

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.M.S. tube

Design, Supply, Erection and Commissioning of Automation System for Pumping Station including PLC, Instruments,Flowmeters etc. And System –Distribution Connectivity in the Distribution Network. We had considering 2 Pumping Station.

Installation testing and commissioning of 33/0.433 KV, 500 KVA, ONAN Type, Dyn 11, OUTDOOR Transformer along with OLTC, HV side Cable Box, LV side Cable box. Work including required tools, tackles, consumables, etc. complete in all respects as per direction of Engineer-in-Charge.

Oil filtration, if required of 33/0.433 KV, 500 KVA, ONAN Type, Dyn 11, Outdoor Transformer along with OLTC including tools, tackles, consumables, etc. complete in all respects as per direction of Engineer-in-Charge.

Supply, installation, testing, and commissioning of 30 kVAr APFC panel, 415V, 3- phase, APFC relay, contactors, and MCBs. Panel shall be fabricated from CRCA sheet, IP42 enclosure, powder coated. Includes voltmeter, ammeter, indicators, and internal wiring. Complete in all respects for indoor mounting and smooth automatic power factor correction.

Installation, Testing and Commissioning of 415 V Main PMCC Panel including 3 no. 145 kW VFD, 3 no. 630A MCCB, 3 nos. 300 A MCCBs, complete in all respects as per SLD.

Supply, Installation, Testing and Commissioning of LPBS (Industrial type, indoor/outdoor, powder coated, ON- push button, mushroom type OFF push button with NO and NC contacts) including tools, tackles, consumables, etc. complete in all respects as per direction of Engineer-in-Charge.

Supply, installation and commissioning of Outdoor Type Lighting Distribution Board with double door arrangement for 1 Nos.with incomer 32 Amp FP RCBO Type Incomer with 6 no Outgoing of 10 Amp 10 KA DP MCB as per drawing including tools, tackles, consumables, etc. complete in all respects as per direction of Engineer-in-Charge.

Supply, installation and commissioning of Indoor Type Lighting Distribution Board (LDB-l) with double door arrangement for 1 no I/C 32A FP RCBO & O/G 6 NO 10 Amp 10KA SP MCBS and 2 no 16Amp 10 KA TPN MCB Outgoing as per drawing including tools, tackles, consumables, etc. complete in all respects as per direction of Engineer-in-Charge.

Supply, testing, tagging, laying and commissioning following sizes of 3300 Volt grade, XLPE / FRLS insulated multistrand Al. / Cu. Conductor armoured / unarmoured cables (As Per IS 1554 & IS 7098) in readymade RCC trench, in provided PVC pipe, RCC pipe hume pipe, on provided cable trays / ladders etc. as. required complete with clamps, hardware for fixing tagging, identification. 3C x 300 Sq.mm. A2XFY FRLS cable.

Supply, Installation, Testing & Commissioning of readymade hot dip galvanized 14/16 SWG perforated trays. Perforated trays shall have support of 75mm 'C' shaped side channels and rungs at 200 mm cc. i)50 mm perforated tray (16 SWG).

100 mm perforated tray (16 SWG).

150 mm perforated tray (16 SWG).

200 mm perforated tray (16 SWG).

Supply and installation of readymade powder coated tray covers fabricated from 16/18 SWG CRCA sheets with readymade accessories. e.g. Bend, Tee's,Rightangles etc. with RAL 7032 shade for all vertical runs. 50 mm perforated tray

100 mm perforated tray

150 mm perforated tray

200 mm perforated tray

GI Conduit-50 mm dia required for cable laying

PVC Conduit-50 mm dia required for cable laying

Fabrication and erection of structural steel for support of tray , panels and oter electrical items.Work includes provide paint and redoxide ( each two coat), all tools, tackles, consumables, etc.for erection are in contractor scope. complete in all respects as per direction of Engineer-in Charge.

Fabrication and erection of 6 mm thick chequered plate and work include supply of paint and red oxide( each two coat) all tools, tackles, consumables, etc. for erection are in vendor scope . complete in all respects as per direction of Engineer-in-Charge.

Supply & Erection, fabrication and testing including excavation earth pit of 600 X 600 X 6 mm GI Plate, 40 mm Dia. 4.5 m. long GI Pipe type earthing,(for Transformer and DG neutral and Instrument earthing) GI Strip, Funnel, Clamp, GI nutbolts, CI cover, etc. for plate Earthing material including preparation of (450 mm X 450 mm) Earth Pit with supply of Bricks, sand, charcoal, salt etc. including tools, tackles, consumables, etc. complete, Printing, Numbering and marking i.e. Pit no., DOT and Ohm value in all respects as per direction of Engineer-in-Charge.

Supply & Erection, fabrication and testing including excavation earth pit of 40 mm Dia. 4.5 m. long GI Pipe type earthing(For Grid and Body earthing), Funnel, Clamp, GI nutbolts, CI cover etc. for pipe Earthing, material including preparation of (450 mm X 450 mm) Earth Pit with supply of Bricks, sand, charcoal, salt etc. including tools, tackles, consumables, etc. complete, Printing, Numbering and marking i.e. Pit no., DOT and Ohm value in all respects as per direction of Engineer-in-Charge.

Supply & Laying and fabrication of 50 mm X 6 mm GI Flat, nut bolt for Earthing including tools, tackles, consumables etc. complete in all respects as per direction of Engineer-in-Charge.

Supply & Laying and fabrication of 25 mm X 3 mm GI Flat, nut bolt for Earthing including tools, tackles, consumables etc. complete in all respects as per direction of Engineer-in-Charge.

Supply & Installation of Earth Bus of GI-Earth BUS-50 mm X 5 mm 300mm length

Supply & Laying and fabrication of 8 SWG Wire for earthing with nut bolt for Earthing including tools, tackles, consumables etc. complete in all respects as per direction of Engineer-in-Charge.

Supply & Laying and fabrication of 8 mm CU conductor for earthing of instrument system with nut bolt for Earthing including tools, tackles, consumables etc. complete in all respects as per direction of Engineer-in- Charge.

3 meter long vertical air terminal with mounting accessories (Lightning Arrestor).

Supply & Erection, fabrication and testing including excavation earth pit of ( 3 m long Copper Bonded Mild steel OF DIA 14.2MM IN PIT FOR Lightning - Protection., Funnel, Clamp, GI nutbolts, CI cover etc. for pipe Earthing, material including preparation of (450 mm X 450 mm) Earth Pit with supply of Bricks, sand, charcoal, salt etc. including tools, tackles, consumables, etc. complete, Printing, Numbering and marking i.e. Pit no., DOT and Ohm value in all respects as per direction of Engineer-in-Charge.

Internal and External lighting and its accessories complete in all aspects

Supply, Installation,Testing, Commissioning of 5 kVA -1 Nos. Online UPS (--- VDC - With Isolation Transformer ) Pure sine wave Double conversion 400V AC In/400 V AC out UPS 30 minutes back up ( Battery set with Interlinks set & battery rack) Suitable to operate from Grid & DG set .And with all standard features & accessories. Static bypass IGBT advance rectifier charger with built in APFC for >0.93 to Unity 6 IGBT PWM DSP inverter with step load 100%, RS 485 port for BMS Factory testing to ISO 62040 part III Battery for UPS 1/2 hr discharge as the per case, comprising 12 V AGM-SMF cells placed on structural steel multitier battery stand, duly epoxy primer +intermidiate +final coat of epoxy paint in dry film thickness of 100 micron & finished in polyeurathane paint in 30 micron complete with intercell connectors, Insulating mat, spanner,thermometer etc.

Supply, installation, testing, and commissioning of 1 No. 110V DC Nickel- Cadmium battery bank of minimum 75Ah capacity , suitable for substation protection, control, and emergency operations, complete with interconnecting links, stands, vent plugs, electrolyte (if applicable), and accessories.

Supply, installation, testing, and commissioning of 1 No. automatic float-cum- boost charger for 110V DC battery system, suitable for continuous float and boost charging modes, with necessary meters, alarms, protections, and control panel, complete in all respects.

Supply, installation, testing, and commissioning of 1 No. 110V DC Distribution Board with incomer and multiple outgoing feeders, equipped with MCBs, indication lamps, terminals, and proper labeling, suitable for protection and control applications in substation environments.

Miscleneous item including safety items

Fabrication and erection of structural steel for support of tray , panels and other electrical items.Work includes provide paint and redoxide ( each two coat), all tools, tackles, consumables, etc.for erection are in contractor scope. complete in all respects as per direction of Engineer-in-Charge.

Fabrication and erection of 6 mm thick chequered plate and work include supply of paint and red oxide( each two coat) all tools, tackles, consumables, etc. for erection are in vendor scope . complete in all respects as per direction of Engineer-in-Charge.

Supplying, laying , testing & commissioning of R.C.C. NP3 Hume pipe with spigot and rubber rings including all accessories, jointing material, laying to level etc. complete. 300 mm diameter

Supplying, Erecting, testing & commissioning of B.B. masonry inspection chambers of following sizes with cement concrete bedding 150 mm thick in cement mortar 1:6 and benching from inside with 1:2:4 CC and plastering with cement mortar 1:3 from inside and outside and fixing air tight pre-cast covers as per the size. 750mm x 750mm x 750mm

Supply, erection, testing, and commissioning of 33 kV overhead HT transmission line from s/s to pump house site using suitable ACSR conductor (e.g.DOG/Raccoon),including poles, insulators,cross-arms,lightning arrestors,stay sets, earthing, DO fuses, AB switches, sag tensioning, route markers, and all accessories complete as per technical specification and site requirement. 4 Pole Structure with Isolators, Lightning Arresters, DO Fuse, Earth Mats with CTs, PTs, Metering panel for 33kV system

Supply of Main 33KV HT Panel comprising of 1 no. 630A VCB I/C & 2 Nos VCB O/G with all accessories & necessary indications metering and protection

Supply, Installation, Testing and commissioning of 25KVA DG Set

Mechanical Works for Pump Station Design, Supply, Installation, Testing & Commissioning of VT Pump Set suitable for inclined intake well — SS impeller, CI/WCB casing, 120 kW (415 V) submersible motor, with discharge bend, rising column, strainer, cable, chain,mechanical seals & fittings complete. (2W + 1S)

PLC-HMI control panel, metering, auto/manual/remote operation, SCADA interface, cabling & earthing. For PH-01

Electrically Operated Hoist (EOT) Design, Drawing, fabrication, supply, erection, testing and commissioning of EOT crane consisting of double girder box type construction, rail mounted end carriages with long and cross travel arrangement, main and auxiliary hoists of specified capacity, rails, pendant control, gear boxes, electric motors, brakes, rope drums, wire ropes, sheaves, end buffer stoppers, pendant operated DSL bus bars with all accessories for main and auxiliary hoists for handling pumps and accessories in pump house including cost of all materials, machinery, labour, cutting, aligning, welding, finishing, cleaning, greasing, applying two coats of zinc chromate red oxide primer and three coats of synthetic enamel paint etc., complete as per specifications and approved drawings with all lead and lifts, including packing & forwarding transportation charges for structural steel components and other materials for PH-01

Electrically Operated Butterfly Valve (BFV) - 300mm Providing, double flanged short body pattern type electrically operated Butterfly Valve of PN10 rating having body, disc andend cover in graded cast iron to IS-210 Gr.CF 200 generally confirming to IS-13095-1991, Synthetic rubber face dring secured on disc by retaining ring with stainless steel screw stub shaft of stainless steel riding inteflonbearing including inspection charges,transportation up to departmental store, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. excluding C.C. foundation /structural steel support.

Dismantling Joint (DJ) 300mm Supplying and fixing Mild Steel (MS) fabricated Dismantling joint confirming to IS 2062 E250 BR including all lead and lifts etc. complete.

Non Return Valve (NRV) 300mm Supplying, installing, testing and commissioning (SITC) Cast steel double flanged dual plate Check valve of PN10 rating Class 150 conforming to API 594 of approved make of specified diameter and to withstand specified pressure with all accessories true to line and perfect linking with pipes on either side including loading, unloading, lifting and placing in correct position, cleaning ends, inserting gaskets into correct position, jointing pipes and valve to form water tight joints, cost of all jointing materials, machinery, labour including all lead and lifts etc. complete.

Flow Meter (FM) 300mm Supplying, installing and commissioning electro-magnetic type flow meter of approved make with all accessories including display panel in the pump house including all lead and lifts.

Air valve (AV) 80mm Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) :

Pressure Gauge

Pressure Transmitter

Installation testing and commissioning of 33/0.433 KV, 250 KVA, ONAN Type, Dyn 11, OUTDOOR Transformer along with OLTC, HV side Cable Box, LV side Cable box. Work including required tools, tackles, consumables, etc. complete in all respects as per direction of Engineer-in-Charge

Oil filtration, if required of 33/0.433 KV, 250 KVA, ONAN Type, Dyn 11, Outdoor Transformer along with OLTC including tools, tackles, consumables, etc. complete in all respects as per direction of Engineer-in-Charge

Supply, installation, testing, and commissioning of 20 kVAr APFC panel, 415V, 3- phase, APFC relay, contactors, and MCBs. Panel shall be fabricated from CRCA sheet, IP42 enclosure, powder coated. Includes voltmeter, ammeter,indicators, and internal wiring. Complete in all respects for indoor mounting and smooth automatic power factor correction

Installation, Testing and Commissioning of 415 V Main PMCC Panel including 3 no. 75 kW VFD, 3 no. 630A MCCB, 3 nos. 300 A MCCBs, complete in all respects as per SLD.

Supply, Installation, Testing and Commissioning of LPBS (Industrial type, indoor/outdoor, powder coated, ON- push button, mushroom type OFF push button with NO and NC contacts) including tools, tackles, consumables, etc. complete in all respects as per direction of Engineer-in-Charge.

Supply, installation and commissioning of Outdoor Type Lighting Distribution Board with double door arrangement for 1 Nos.with incomer 32 Amp FP RCBO Type Incomer with 6 no Outgoing of 10 Amp 10 KA DP MCB as per drawing including tools, tackles, consumables, etc. complete in all respects as per direction of Engineer-in-Charge.

Supply, installation and commissioning of Indoor Type Lighting Distribution Board (LDB-l) with double door arrangement for 1 no I/C 32A FP RCBO & O/G 6 NO 10 Amp 10KA SP MCBS and 2 no 16Amp 10 KA TPN MCB Outgoing as per drawing including tools, tackles, consumables, etc. complete in all respects as per direction of Engineer-in-Charge.

Supply, testing, tagging, laying and commissioning following sizes of 3300 Volt grade, XLPE / FRLS insulated multistrand Al. / Cu. Conductor armoured / unarmoured cables (As Per IS 1554 & IS 7098) in readymade RCC trench, in provided PVC pipe, RCC pipe hume pipe, on provided cable trays / ladders etc. as. required complete with clamps, hardware for fixing tagging, identification 3C x 300 Sq.mm. A2XFY FRLS cable.

Supply, Installation, Testing & Commissioning of readymade hot dip galvanized 14/16 SWG perforated trays. Perforated trays shall have support of 75mm 'C' shaped side channels and rungs at 200 mm cc. 50 mm perforated tray (16 SWG).

100 mm perforated tray (16 SWG).

150 mm perforated tray (16 SWG).

200 mm perforated tray (16 SWG).

Supply and installation of readymade powder coated tray covers fabricated from 16/18 SWG CRCA sheets with readymade accessories. e.g. Bend, Tee's, Rightangles etc. with RAL 7032 shade for all vertical runs 50 mm perforated tray

100 mm perforated tray

150 mm perforated tray

200 mm perforated tray

GI Conduit-50 mm dia required for cable laying

PVC Conduit-50 mm dia required for cable laying

Fabrication and erection of structural steel for support of tray , panels and oter electrical items.Work includes provide paint and redoxide ( each two coat), all tools, tackles, consumables, etc.for erection are in contractor scope. complete in all respects as per direction of Engineer-in-Charge.

Fabrication and erection of 6 mm thick chequered plate and work include supply of paint and red oxide( each two coat) all tools, tackles, consumables, etc. for erection are in vendor scope . complete in all respects as per direction of Engineer-in-Charge.

Supply & Erection, fabrication and testing including excavation earth pit of 600 X 600 X 6 mm GI Plate, 40 mm Dia. 4.5 m. long GI Pipe type earthing,(for Transformer and DG neutral and Instrument earthing) GI Strip, Funnel, Clamp, GI nutbolts, CI cover, etc. for plate Earthing material including preparation of (450 mm X 450 mm) Earth Pit with supply of Bricks, sand, charcoal, salt etc. including tools, tackles, consumables, etc. complete, Printing, Numbering and marking i.e. Pit no., DOT and Ohm value in all respects as per direction of Engineer-in-Charge.

Supply & Erection, fabrication and testing including excavation earth pit of 40 mm Dia. 4.5 m. long GI Pipe type earthing(For Grid and Body earthing), Funnel, Clamp, GI nutbolts, CI cover etc. for pipe Earthing, material including preparation of (450 mm X 450 mm) Earth Pit with supply of Bricks, sand, charcoal, salt etc. including tools, tackles, consumables, etc. complete, Printing, Numbering and marking i.e. Pit no., DOT and Ohm value in all respects as per direction of Engineer-in-Charge.

Supply & Laying and fabrication of 50 mm X 6 mm GI Flat, nut bolt for Earthing including tools, tackles, consumables etc. complete in all respects as per direction of Engineer-in-Charge.

Supply & Laying and fabrication of 25 mm X 3 mm GI Flat, nut bolt for Earthing including tools, tackles, consumables etc. complete in all respects as per direction of Engineer-in-Charge.

Supply & Installation of Earth Bus of GI-Earth BUS-50 mm X 5 mm 300mm length

Supply & Laying and fabrication of 8 SWG Wire for earthing with nut bolt for Earthing including tools, tackles, consumables etc. complete in all respects as per direction of Engineer-in-Charge.

Supply & Laying and fabrication of 8 mm CU conductor for earthing of instrument system with nut bolt for Earthing including tools, tackles, consumables etc. complete in all respects as per direction of Engineer-in-Charge.

3 meter long vertical air terminal with mounting accessories (Lightning Arrestor).

Supply & Erection, fabrication and testing including excavation earth pit of ( 3 m long Copper Bonded Mild steel OF DIA 14.2MM IN PIT FOR Lightning - Protection., Funnel, Clamp, GI nutbolts, CI cover etc. for pipe Earthing, material including preparation of (450 mm X 450 mm) Earth Pit with supply of Bricks, sand, charcoal, salt etc. including tools, tackles, consumables, etc. complete, Printing, Numbering and marking i.e. Pit no., DOT and Ohm value in all respects as per direction of Engineer-in-Charge.

Internal and External lighting and its accessories complete in all aspects

Supply, Installation,Testing, Commissioning of 5 kVA -1 Nos. Online UPS (--- VDC - With Isolation Transformer ) Pure sine wave Double conversion 400V AC In/400 V AC out UPS 30 minutes back up ( Battery set with Interlinks set & battery rack) Suitable to operate from Grid & DG set .And with all standard features & accessories. Static bypass IGBT advance rectifier charger with built in APFC for >0.93 to Unity 6 IGBT PWM DSP inverter with step load 100%, RS 485 port for BMS Factory testing to ISO 62040 part III Battery for UPS 1/2 hr discharge as the per case, comprising 12 V AGM-SMF cells placed on structural steel multitier battery stand, duly epoxy primer +intermidiate +final coat of epoxy paint in dry film thickness of 100 micron & finished in polyeurathane paint in 30 micron complete with intercell connectors, Insulating mat, spanner,thermometer etc.

Supply, installation, testing, and commissioning of 1 No. 110V DC Nickel- Cadmium battery bank of minimum 50Ah capacity , suitable for substation protection, control, and emergency operations, complete with interconnecting links, stands, vent plugs, electrolyte (if applicable), and accessories.

Supply, installation, testing, and commissioning of 1 No. automatic float-cum- boost charger for 110V DC battery system, suitable for continuous float and boost charging modes, with necessary meters, alarms, protections, and control panel, complete in all respects.

Supply, installation, testing, and commissioning of 1 No. 110V DC Distribution Board with incomer and multiple outgoing feeders, equipped with MCBs, indication lamps, terminals, and proper labeling, suitable for protection and control applications in substation environments.

Miscleneous item inclung safety items

Fabrication and erection of structural steel for support of tray , panels and other electrical items.Work includes provide paint and redoxide ( each two coat), all tools, tackles, consumables, etc.for erection are in contractor scope. complete in all respects as per direction of Engineer-in-Charge.

Fabrication and erection of 6 mm thick chequered plate and work include supply of paint and red oxide( each two coat) all tools, tackles, consumables, etc. for erection are in vendor scope . complete in all respects as per direction of Engineer-in-Charge.

Supplying, laying , testing & commissioning of R.C.C. NP3 Hume pipe with spigot and rubber rings including all accessories, jointing material, laying to level etc. complete. 300 mm diameter

Supplying, Erecting, testing & commissioning of B.B. masonry inspection chambers of following sizes with cement concrete bedding 150 mm thick in cement mortar 1:6 and benching from inside with 1:2:4 CC and plastering with cement mortar 1:3 from inside and outside and fixing air tight pre-cast covers as per the size. 750mm x 750mm x 750mm

4 Pole Structure with Isolators, Lightning Arresters, DO Fuse, Earth Mats with CTs, PTs, Metering panel for 33kV system

Supply of Main 33KV HT Panel comprising of 1 no. 630A VCB I/C & 2 Nos VCB O/G with all accessories & necessary indications metering and protection

Supply, Installation, Testing and commissioning of 20KVA DG Set

Design, Supply, Installation, Testing & Commissioning of VT Pump Set suitable for inclined intake well — SS impeller, CI/WCB casing, 70 kW (415 V) submersible motor, with discharge bend, rising column, strainer, cable, chain, mechanical seals & fittings complete. (2W + 1S)

PLC-HMI control panel, metering, auto/manual/remote operation, SCADA interface, cabling & earthing. For PH-02.

Electrically Operated Hoist (EOT) Design, Drawing, fabrication, supply, erection, testing and commissioning of EOT crane consisting of double girder box type construction, rail mounted end carriages with long and cross travel arrangement, main and auxiliary hoists of specified capacity, rails, pendant control, gear boxes, electric motors, brakes, rope drums, wire ropes, sheaves, end buffer stoppers, pendant operated DSL bus bars with all accessories for main and auxiliary hoists for handling pumps and accessories in pump house including cost of all materials, machinery, labour, cutting, aligning, welding, finishing, cleaning, greasing, applying two coats of zinc chromate red oxide primer and three coats of synthetic enamel paint etc., complete as per specifications and approved drawings with all lead and lifts, including packing & forwarding transportation charges for structural steel components and other materials for PH-02

Electrically Operated Butterfly Valve (BFV) - 200mm Providing, double flanged short body pattern type electrically operated Butterfly Valve of PN10 rating having body, disc andend cover in graded cast iron to IS-210 Gr.CF 200 generally confirming to IS-13095-1991, Synthetic rubber face dring secured on disc by retaining ring with stainless steel screwstub shaft of stainless steel ridinginteflon bearing including inspection charges,transportation up to departmental store, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. excluding C.C. foundation/structural steel support.

Dismantling Joint (DJ) 200mm Supplying and fixing Mild Steel (MS) fabricated Dismantling joint confirming to IS 2062 E250 BR including all lead and lifts etc. complete.

Non Return Valve (NRV) 200mm Supplying, installing, testing and commissioning (SITC) Cast steel double flanged dual plate Check valve of PN10 rating Class 150 conforming to API 594 of approved make of specified diameter and to withstand specified pressure with all accessories true to line and perfect linking with pipes on either side including loading, unloading, lifting and placing in correct position, cleaning ends, inserting gaskets into correct position, jointing pipes and valve to form water tight joints, cost of all jointing materials, machinery, labour including all lead and lifts etc. complete.

Flow Meter (FM) 200mm Supplying, installing and commissioning electro-magnetic type flow meter of approved make with all accessories including display panel in the pump house including all lead and lifts.

Air valve (AV) 80mm Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) :

Pressure Gauge

Pressure Transmitter

Surge Protection System. Design, Supply, Erection and Commissioning of Surge Protection System.

Primary Filtration System Design,Supply,Erection and Commissioning of Self Cleaning Primary Filtration Systemof 200 Micron at Intake or Suitable Pumping Station.

Excavating trenches by mechinical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm In ordinary soil

Supply and delivery of DI Pipes as per IS : 8329/2000 including cost and conveyance, excluding taxes etc. complete.including transportation charges and Loading, unloading and stacking,Lowering C.I. / D.I. Pipes (all classes) and specials (fittings) with s/s ends carefully into trenches and laying them true to alignment and gradient including all sundries but excluding cost and conveyance of pipes from source of supply (Ref to specifications. BIS No. 3114 / 1994), Jointing C.I., D.I. pipes and fittings with rubber gasket (push-on-joint), excluding the cost of the gasket but including all sundries filling with water, with a water lead up to 500m and testing to required pressure, etc. complete Reference to specifications IS 3114/1994/12888/1987 DI (K-7) PIPELINE 300

Supply and delivery of DI Pipes as per IS : 8329/2000 including cost and conveyance, excluding taxes etc. complete.including transportation charges and Loading, unloading and stacking,Lowering C.I. / D.I. Pipes (all classes) and specials (fittings) with s/s ends carefully into trenches and laying them true to alignment and gradient including all sundries but excluding cost and conveyance of pipes from source of supply (Ref to specifications. BIS No. 3114 / 1994), Jointing C.I., D.I. pipes and fittings with rubber gasket (push-on-joint), excluding the cost of the gasket but including all sundries filling with water, with a water lead up to 500m and testing to required pressure, etc. complete Reference to specifications IS 3114/1994/12888/1987 DI (K-7) PIPELINE 350

Supply and delivery of DI Pipes as per IS : 8329/2000 including cost and conveyance, excluding taxes etc. complete.including transportation charges and Loading, unloading and stacking,Lowering C.I. / D.I. Pipes (all classes) and specials (fittings) with s/s ends carefully into trenches and laying them true to alignment and gradient including all sundries but excluding cost and conveyance of pipes from source of supply (Ref to specifications. BIS No. 3114 / 1994), Jointing C.I., D.I. pipes and fittings with rubber gasket (push-on-joint), excluding the cost of the gasket but including all sundries filling with water, with a water lead up to 500m and testing to required pressure, etc. complete Reference to specifications IS 3114/1994/12888/1987 DI (K-7) PIPELINE 400

Supply and delivery of DI Pipes as per IS : 8329/2000 including cost and conveyance, excluding taxes etc. complete.including transportation charges and Loading, unloading and stacking,Lowering C.I. / D.I. Pipes (all classes) and specials (fittings) with s/s ends carefully into trenches and laying them true to alignment and gradient including all sundries but excluding cost and conveyance of pipes from source of supply (Ref to specifications. BIS No. 3114 / 1994), Jointing C.I., D.I. pipes and fittings with rubber gasket (push-on-joint), excluding the cost of the gasket but including all sundries filling with water, with a water lead up to 500m and testing to required pressure, etc. complete Reference to specifications IS 3114/1994/12888/1987 DI (K-7) PIPELINE 500

DI SPECIALS

Design, Supply, Erection and Commissioning of Village Management System (VMS) in Village for Flow Control/Pressure Control/Metering/ON-OFF from Remote as and when required for Isolation of downward Network and ease of commissioning.

Design, Supply, Erection and Commissioning of Air Management System consist of Air Valve with Isolation Valves along with AMS Control Unit for Burst Monitoring by Pressure Monitoring at Air Valve Location in Distribution Network of 1431 Ha

Providing double flange sluice valve confirming for IS- 14846 including worn gear arrangements as per test pressure, stainless steel spindle, caps, including inspection charges, transportation upto departmental store, unloading, stacking excluding GST levied by GOI & GOM in all respect etc.complete. Sluice valves - PN -1.6 (With by pass arrangement) 100MM

Lowering, laying and jointing in position following C.I.D/F Reflex valves, Butterfly valves and Sluice valves including cost of all labour jointing material, including nut bolts and giving satisfactory hydraulic testing etc.complete.(Rate for all class of valves.) 100MM

Providing, double flanged short body pattern type manually operated Butterfly Valve having body, disc and end cover in graded cast iron to IS-210 Gr.CF 200 generally confirming to IS-13095-1991, Synthetic rubber faced ring secured on disc by retaining ring with stainless steel screw stub shaft of stainless steel riding in teflon bearing including inspection charges, transportation up to departmental store, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. excluding C.C. foundation /structural steel support. Butterfly valve - PN - 1.6 (With by pass arrangement) 500 mm.

Lowering, laying and jointing in position following C.I.D/F Reflex valves, Butterfly valves and Sluice valves including cost of all labour jointing material, including nut bolts and giving satisfactory hydraulic testing etc. complete. (Rate for all class of valves.) 500MM

Providing and supplying Kinetic Double Orifice type Air Valves confirming to IS 14845 as per MJP’s standard specifications combined with screw down isolating valve,small orifice elastic ball resting on a gun metal orifice nipple,large orifice vulcanite ball seating on moulded seat ring, inlet face and drilled,including insurance, third party inspection charges, loading, unloading, transportation upto departmental stores, excluding GST levied by GOI & GOM in all respect etc.complete. Kinetic Air Valve Flanged Type - PN - 1 40 mm.

Providing and supplying Kinetic Double Orifice type Air Valves confirming to IS 14845 as per MJP’s standard specifications combined with screw down isolating valve,small orifice elastic ball resting on a gun metal orifice nipple,large orifice vulcanite ball seating on moulded seat ring, inlet face and drilled,including insurance, third party inspection charges, loading, unloading, transportation upto departmental stores, excluding GST levied by GOI & GOM in all respect etc.complete. Kinetic Air Valve Flanged Type - PN - 1 50 mm.

Providing and supplying Kinetic Double Orifice type Air Valves confirming to IS 14845 as per MJP’s standard specifications combined with screw down isolating valve,small orifice elastic ball resting on a gun metal orifice nipple,large orifice vulcanite ball seating on moulded seat ring, inlet face and drilled,including insurance, third party inspection charges, loading, unloading, transportation upto departmental stores, excluding GST levied by GOI & GOM in all respect etc.complete. Kinetic Air Valve Flanged Type - PN - 1 80 mm.

Providing and supplying Kinetic Double Orifice type Air Valves confirming to IS 14845 as per MJP’s standard specifications combined with screw down isolating valve,small orifice elastic ball resting on a gun metal orifice nipple,large orifice vulcanite ball seating on moulded seat ring, inlet face and drilled,including insurance, third party inspection charges, loading, unloading, transportation upto departmental stores, excluding GST levied by GOI & GOM in all respect etc.complete. Kinetic Air Valve Flanged Type - PN - 1 100 mm.

Lowering, laying and fixing in proper alignment andpositionall types of C.I. air valves as directed by Engineer-in-charge including cost of conveyance from stores to site of work, cost of all material and giving satisfactory hydraulic testing, etc. complete.(for all class of valves). Kinetic Air Valve Flanged Type - PN - 1 40 mm.

Lowering, laying and fixing in proper alignment andpositionall types of C.I. air valves as directed by Engineer-in-charge including cost of conveyance from stores to site of work, cost of all material and giving satisfactory hydraulic testing, etc. complete.(for all class of valves). Kinetic Air Valve Flanged Type - PN - 1 50 mm.

Lowering, laying and fixing in proper alignment andpositionall types of C.I. air valves as directed by Engineer-in-charge including cost of conveyance from stores to site of work, cost of all material and giving satisfactory hydraulic testing, etc. complete.(for all class of valves). Kinetic Air Valve Flanged Type - PN - 1 80 mm.

Lowering, laying and fixing in proper alignment andpositionall types of C.I. air valves as directed by Engineer-in-charge including cost of conveyance from stores to site of work, cost of all material and giving satisfactory hydraulic testing, etc. complete.(for all class of valves). Kinetic Air Valve Flanged Type - PN - 1 100 mm.

Construction of R.C.C. Butterfly Valve Chamber (2.60 m × 2.60 m × 2.80 m internal size) comprising earthwork in excavation in all kinds of soil; providing and laying PCC M15 at base; providing and laying R.C.C. M20 for base slab, vertical walls, top slab and pedestal, excluding centering and shuttering; providing and fixing steel reinforcement of grade Fe-500D including cutting, bending, placing and binding complete; and providing 12 mm thick cement plaster in vertical walls with cement mortar 1:4 (1 cement : 4 fine sand), complete in all respects as per drawings, specifications and directions of Engineer-in-Charge

Construction of R.C.C SCOUR VALVE CHAMBER (1M X 1M X 2.43M) internal size) comprising earthwork in excavation in all kinds of soil; providing and laying PCC M15 at base; providing and laying R.C.C. M20 for base slab, vertical walls, top slab and pedestal, excluding centering and shuttering; providing and fixing steel reinforcement of grade Fe-500D including cutting, bending, placing and binding complete; and providing 12 mm thick cement plaster in vertical walls with cement mortar 1:4 (1 cement : 4 fine sand), complete in all respects as per drawings, specifications and directions of Engineer-in-Charge

Construction of Thrust block comprising earthwork in excavation in all kinds of soil; providing and laying PCC M15 at base; providing and laying R.C.C. M20 for pedestal, excluding centering and shuttering; providing and fixing steel reinforcement of grade Fe-500D including cutting, bending, placing and binding complete; complete in all respects as per drawings, specifications and directions of Engineer-in-Charge For 45° angle of bend for DI-500 mm Dia.

For 11.25° angle of bend for HDPE-350 mm Dia.

For 22.5° angle of bend for HDPE-350 mm Dia.

For 11.25° angle of bend for HDPE-300 mm Dia.

For 22.5° angle of bend for HDPE-300 mm Dia.

Construction of encasing comprising earthwork in excavation in all kinds of soil; providing and laying PCC M15 at base; providing and laying R.C.C. M20 for pedestal, excluding centering and shuttering; providing and fixing steel reinforcement of grade Fe-500D including cutting, bending, placing and binding complete; complete in all respects as per drawings, specifications and directions of Engineer-in-Charge For River (Stream) Crossing ABS HDPE-250 mm Dia.

For River (Stream) Crossing ABS HDPE-315 mm Dia.

For River (Stream) Crossing ABS DI-350 mm Dia.

Providing and laying 600 mm dia NP-4 class heavy duty R.C.C. pipes including collars/spigot joints with stiff cement mortar 1:2 (1 cement : 2 fine sand), testing of joints etc. complete, by trenchless pipe jacking method, including setting out, hydraulic pipe jacking, tunnelling, excavation in all types of soil including hard rock, alignment and gradient control, erection and removal of equipment, construction of RCC jacking and receiving pits/chambers, conveyance of machinery and materials, and coordination with concerned authorities, complete as per approved drawings and directions of Engineer-in-Charge; including PCC 1:2:4 for head wall and two wing walls, complete.

Excavating trenches by mechinical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm Total Quantity of exceeding 80 mm dia. but not exceeding 300 mm dia.

Total Quantity of exceeding 300 mm dia. but not exceeding 600 mm dia.

Manufacture of HDPE Pipes conforming to IS 4984 - 2016 excluding all taxes (Supply up to 110 mm dia. in coil & above 110 mm dia. straight length.) and Laying and jointing of HDPE pipes by butt fusion welding as per IS:7634 – part-II/1975 as amended from time to time to the alignment and gradient and testing the pipeline to the required pressure. HDPE (PE-100) PN-6 PIPELINE 110

Manufacture of HDPE Pipes conforming to IS 4984 - 2016 excluding all taxes (Supply up to 110 mm dia. in coil & above 110 mm dia. straight length.) and Laying and jointing of HDPE pipes by butt fusion welding as per IS:7634 – part-II/1975 as amended from time to time to the alignment and gradient and testing the pipeline to the required pressure. HDPE (PE-100) PN-6 PIPELINE 125

Manufacture of HDPE Pipes conforming to IS 4984 - 2016 excluding all taxes (Supply up to 110 mm dia. in coil & above 110 mm dia. straight length.) and Laying and jointing of HDPE pipes by butt fusion welding as per IS:7634 – part-II/1975 as amended from time to time to the alignment and gradient and testing the pipeline to the required pressure. HDPE (PE-100) PN-6 PIPELINE 140

Manufacture of HDPE Pipes conforming to IS 4984 - 2016 excluding all taxes (Supply up to 110 mm dia. in coil & above 110 mm dia. straight length.) and Laying and jointing of HDPE pipes by butt fusion welding as per IS:7634 – part-II/1975 as amended from time to time to the alignment and gradient and testing the pipeline to the required pressure. HDPE (PE-100) PN-6 PIPELINE 160

Manufacture of HDPE Pipes conforming to IS 4984 - 2016 excluding all taxes (Supply up to 110 mm dia. in coil & above 110 mm dia. straight length.) and Laying and jointing of HDPE pipes by butt fusion welding as per IS:7634 – part-II/1975 as amended from time to time to the alignment and gradient and testing the pipeline to the required pressure. HDPE (PE-100) PN-6 PIPELINE 180

Manufacture of HDPE Pipes conforming to IS 4984 - 2016 excluding all taxes (Supply up to 110 mm dia. in coil & above 110 mm dia. straight length.) and Laying and jointing of HDPE pipes by butt fusion welding as per IS:7634 – part-II/1975 as amended from time to time to the alignment and gradient and testing the pipeline to the required pressure. HDPE (PE-100) PN-6 PIPELINE 200

Manufacture of HDPE Pipes conforming to IS 4984 - 2016 excluding all taxes (Supply up to 110 mm dia. in coil & above 110 mm dia. straight length.) and Laying and jointing of HDPE pipes by butt fusion welding as per IS:7634 – part-II/1975 as amended from time to time to the alignment and gradient and testing the pipeline to the required pressure. HDPE (PE-100) PN-6 PIPELINE 225

Manufacture of HDPE Pipes conforming to IS 4984 - 2016 excluding all taxes (Supply up to 110 mm dia. in coil & above 110 mm dia. straight length.) and Laying and jointing of HDPE pipes by butt fusion welding as per IS:7634 – part-II/1975 as amended from time to time to the alignment and gradient and testing the pipeline to the required pressure. HDPE (PE-100) PN-6 PIPELINE 250

Manufacture of HDPE Pipes conforming to IS 4984 - 2016 excluding all taxes (Supply up to 110 mm dia. in coil & above 110 mm dia. straight length.) and Laying and jointing of HDPE pipes by butt fusion welding as per IS:7634 – part-II/1975 as amended from time to time to the alignment and gradient and testing the pipeline to the required pressure. HDPE (PE-100) PN-6 PIPELINE 280

Manufacture of HDPE Pipes conforming to IS 4984 - 2016 excluding all taxes (Supply up to 110 mm dia. in coil & above 110 mm dia. straight length.) and Laying and jointing of HDPE pipes by butt fusion welding as per IS:7634 – part-II/1975 as amended from time to time to the alignment and gradient and testing the pipeline to the required pressure. HDPE (PE-100) PN-6 PIPELINE 315

H.D.P.E. SPECIALS

Design, Supply, Erection and Commissioning of Outlet Management System (OMS) with Rotation for 5 Ha at 30 Ha for Flow/Pressure Control/Metering/ON-OFF from Remote as and when required for equitable distribution of water.

Excavating trenches by mechinical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc, not exceeding 80 mm dia. Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm diaTotal Quantity of not exceeding 80 mm dia.

Total Quantity of exceeding 80 mm dia. but not exceeding 300 mm dia.

Manufacture of HDPE Pipes conforming to IS 4984 - 2016 excluding all taxes (Supply up to 110 mm dia. in coil & above 110 mm dia. straight length.) and Laying and jointing of HDPE pipes by butt fusion welding as per IS:7634 – part-II/1975 as amended from time to time to the alignment and gradient and testing the pipeline to the required pressure. HDPE (PE-100) PN-6 PIPELINE 63

Manufacture of HDPE Pipes conforming to IS 4984 - 2016 excluding all taxes (Supply up to 110 mm dia. in coil & above 110 mm dia. straight length.) and Laying and jointing of HDPE pipes by butt fusion welding as per IS:7634 – part-II/1975 as amended from time to time to the alignment and gradient and testing the pipeline to the required pressure. HDPE (PE-100) PN-6 PIPELINE 75

Manufacture of HDPE Pipes conforming to IS 4984 - 2016 excluding all taxes (Supply up to 110 mm dia. in coil & above 110 mm dia. straight length.) and Laying and jointing of HDPE pipes by butt fusion welding as per IS:7634 – part-II/1975 as amended from time to time to the alignment and gradient and testing the pipeline to the required pressure. HDPE (PE-100) PN-6 PIPELINE 90

H.D.P.E. SPECIALS

High Pressure HDPE Irrigation Ball Valve Size : 20-250 mm

Ball valve chamber ( R.C.C. pipes NP2 class 300 mm dia)

Operation and Maintenance of five years (@1% per annum) Daily operation of the PPIC system including the pumping, air management, flow and pressure control management systems, SCADA system, which will allow real time remote monitoring of pump operations, and flows and pressures at Hubs and Outlets of the PPIC system System maintenance requirements of the system starting with debris removal, removal of trash from screens, de-sedimentation from basins, at the head of each PPIC system, Maintenance of the PPIC systems requires the timely replacement of broken flow and pressure control devices, flow meters, pumps, and regular cleaning of screens and filters. SCADA system is also important. Routine hardware maintenance includes the replacement of failed sensors, old batteries, and compromised wiring. Even with lightning protection, a site experiencing a direct strike may require complete replacement of equipment. For pumping equipment, the manufacturers’ maintenance instructions for periodic checks and inspections for noise, vibration, leakage, temperatures of bearings and windings, fuel/ power consumption, capacity, and output (water discharge and dynamic head), ventilation, may be detailed.

Provisional Payment to APDCL for Sanction & Extension of power supply

Please Enable Macros to View BoQ information