Signaling work in connection with Fencing work in KALYAN - KARJAT - LONAVALA and KARJAT - KHOPOLI section in Mumbai division.

Supply of PVC indoor cable 1x24x1 mm dia. Color coding of insulation of Inner conductor shall be in eight colour viz, Blue, Red, Grey, Green, Brown, Black, Yellow & white confirming to IRS 76/89 (Amd. 3) or latest.

Supply of Indoor Jumper wire of various colour as per Railways standard practice of type ATC 1x0.6 mm dia. Conforming to IRS/76/89 (Amd.3) of latest.

Supply of Indoor Jumper wire ATC 1x1 mm dia. Conforming to IRS/76/89 (Amd.3) of latest.

Supply of PVC flexible copper cable single core, multistrand 1x16 Sq.mm (126 04 conductor each diameter 0.40 +/- 0.01) as per IS 2465/1984 & IS: 694/2010. with latest amendment if any with insulation thickness of 1.0mm nominal conductor resistance 1.121 ohms/km and test parameters are as per IRS (S) 76/89 (Amd.3)or latest.

Supply of PVC flexible copper cable single core, multistrand 1x25 Sq.mm (196 05 conductor each diameter 0.40 +/- 0.01) as per IS 2465/1984 & IS: 694/2010. with latest amendment if any with insulation thickness of 1.2mm nominal conductor resistance 0.780 ohms/km and test parameters are as per IRS (S) 76/89 (Amd.3)or latest.

Supply of wire 16/0.2 (Blue, Red, Grey, yellow, Brown, Black, White as per site engineer instruction) finolex/polycab/delton make. IRS:S-76/89 (Amd.3), BS: 4808 Part-2. Wire to be procured from RDSO approved vender.

Sealed maintenance free VRLA Battery/Cell 2 volt, 300AH IRS: S-93/96 (A) (Amd.1) or latest.

Sealed maintenance free VRLA Battery/Cell 2 volt, 200AH RDSO SPN/93/96 (A) (Amd.1) or latest.

Supply of Program switches with acrylic cover, snap action, base mounting type along with cover and mounting bracket 25A-7 pole 3 position Siemens (3 LAO-25/7Y)/ L&T/HEVELS type. Drg. No.RST.C.106.

Supply of Program switches, snap action, base mounting type along with cover and mounting bracket 63A-7 pole 3 position Siemens (3 LAO-63/7Y)/L&T/HEVELS type Drg.No.RST.C.106.

Supply of Battery charger self regulating floor mounting type with 230 V AC single phase input and output 60 V DC, 20 A as per spec.IRS.S.86/2000 (Amd.4) with latest amendments.

Supply of Battery charger self regulating floor mounting type with 230 V AC single phase input and output 24 V DC, 20 A as per spec.IRS.S.86/2000 with latest amendment for Axle counter application (Amd.4)

Supply of Battery charger self regulating floor mounting type with 230 V AC single phase input and output 24 V DC,30 A t o spec.IRS.S.86/2000 (Amndt-1) with latest amendment for Axle counter application (Amd.4)

Supply of Rubber Mat 5mm thick for use in signaling installation.

Supply of Automatic changeover for individual supply. Automatic changeover unit of 15 signal / Track / DC circuit supply of 32A, AC/DC consisting of 3TC44 contractors, LED Lamp, Push button, terminals, VSR, polarity switches. As per Rly. Drg.-SK-841/1-5 for IPS supply to manual discrete equipments with P/switch.

Supply of signal group 2 aspect without base plate Siemens make (No.A-RT-RG-A066) or functional equivalent and should be suitable for working with LED based signal lighting unit.

Supply of signal group 3 aspect without base plate Siemens make (No.A-RT-RG-A067) or functional equivalent and should be suitable for working with LED based signal lighting unit.

Supply of signal group, 4 aspect Siemens make (No.A-RT-RG-A057) or functional equivalent without base plates.

Supply of Shunt signal group Siemens make (No.A-RT-RG-A065) or functional equivalent without base plates (suitable for LED signal)

Supply of Point Group RRI, Siemens make (No.RSSK 3515/19) or functional equivalent without base plates.

Supply of Point Chain Group Siemens make (No.RSSK 3515/3) or functional equivalent without base plates.

Supply of Key Lock Relay with different ward combinations (Three extra set of ward 22 plate for point Machine to be supplied with each relay). Siemens make working on 60V DC/24 DC or functional equivalent without base plates. RDSO/SPN/219/2016 version 1.0 with Amendment No.1 or latest.

Supply of Auto signal Block proving Relay Group Siemens make (No.A-RT-RG-A056) or functional equivalent without base plates.

Supply of Block filter unit as per IRS:S-68/89 and Block bell equipment as per IRS:TC- 44/88 (Amd. 1).

Supply of Block Bell equipment as per RDSO Drg. No.TCA 15080 and Spec. No IRS-TC- 44/88 (Amd.1) with amendment No. 1 Voltage 24 V DC.

Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:-78-92 With holder 1.6 A (System, Rapid or Malnad Make).

Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:-78-92 With holder 0.6 A (System, Rapid or Malnad Make).

Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:-78-92 With holder 6 A/10A (D- Type Bharat Linder, L&T or HEVELLS Make).

Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:-78-92 Without holder 1.6 A (System, Rapid or Malnad Make).

Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:-78-92 Without holder 0.6 A (System, Rapid or Malnad Make).

Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:-78-92 Without holder 6 A/10A (D-Type Bharat Linder, L&T or HEVELLS Make).

Supply of PPTC Fuse GP 60-185 UL-94 certification (1.6 Amps) for internal / external current. Make: LITTLEFUSE, FUZETEC, TYCO, BOURN, RAYCHEM etc.

Supply of Resisters, condensers, Diodes, LEDs and lugs alongwith bracket and mounting arrangement as per standard Annexure-V of Central Railway.

Lacing thread rolls, black, wax coated (100 mtrs) Each

Design, fabrication and supply of fuse Auto changeover system for 32 Nos external non detorating type fuses or 'G' type fuses from 0.6A Amp to 4A Amp capacities used in signaling circuits. System shall have 8 cards with monitoring arrangement of 4 fuses in one card. As per RDSO spec. RDSO/SPN/209/2012 Ver.2.0 or latest amendment if any. Each

Design, fabrication and supply of fuse Auto changeover system for 24 Nos external non detorating type fuses or 'G' type fuses from 4 A to 10 Amp capacities generally used for point operation circuits. System shall have 6 cards with monitoring arrangement of 4 fuses in one card. As per RDSO spec. RDSO/SPN/209/2012 Ver.2.0 or latest amendment if any.

Supply of Main signal post 140 mm outer dia 3.6 Mtr Length as per spec No.IRS S 6/81 with latest amendments.

Supply of Main signal post 140 mm outer dia 4.6 Mtr Length as per spec No.IRS S 6/81 with latest amendments.

Supply of Main signal post 140 mm outer dia 5.6 Mtr Length as per spec No.IRS S 6/81 with latest amendments.

Supply of Cast Iron Main signal surface base 140mm as per spec No IRS: S-10 and 40 Drg No 2011/M with latest amendments, with CLS Ladder assembly complete for CLS signal 5.5/4.5/3.5 mtrs long as per RDSO Drg no. SA 23156 (Adv), SA 23153 (Adv) & SA 23150 (Adv) Alt.1 respectively with Latest Amendment as the case may be for CLS unit & signal back staging as per extent C.Rly practice.

Supply of Signal No.Plates as per Drg No RST-11393/ SK-842

OFF set bracket 5-1/2" to suit 140 mm dia CLS Post with two no. of "U" Bolts with nut & washer complete as per RDSO Drg No SA-23080 for signals & Routes.

Supply of A/AG/C/P/G/IB Board as per Drg. RST-11444/1(A), RDSO Drg No SA- 23460(AG), SA-23461(C) , RST-11445, SA 23456(P), SA 23477(G) & SA 23476-77 (IB) as applicable respectively with Latest Amendment.

Supply of Stop Board / IB Board as per RST-11791 (STOP BOARD)/ RDSO Drg No 7235/B as per extent C.Rly practice.

Supply of different warning Board as per Goods warning Board (SK-784) RDSO Drg No. SA 2380 (Adv), SA 2370/M-, Block section limit Board RDSO Drg No. SA 2373 - Paint and retroreflective arrangement as per Railways drawing.

Supply of Hand Cuff Locks / Godrej Navtal lock with Three common keys.

Supply of "2 aspect" Signal Unit in FRP body without lenses and transformers as per 47 RDSO Specification RDSO/SPN/194/2006/Rev.2.0 or latest complete and to suit LED signal Lamps and suitable for 140 mm dia post saves pigment finish on the back side of the and inside. white pigment finish inside the 2 aspect unit to avoid any extra paint cost

Supply of "3 aspect" Signal Unit in FRP body without lenses and transformers as per 48 RDSO Specification RDSO/SPN/194/2006/Rev.2.0 or latest complete and to suit LED signal Lamps and suitable for 140 mm dia post saves pigment finish on the back side of the and inside. white pigment finish inside the 4 aspect unit to avoide any extra paint cost

Supply of "4 aspect" Signal Unit in FRP body without lenses and transformers as per 49 RDSO Specification RDSO/SPN/194/2006/Rev.2.0 or latest complete and to suit LED signal Lamps and suitable for 140 mm dia post saves pigment finish on the back side of the and inside. white pigment finish inside the 4 aspect unit to avoid any extra paint cost

Supply of Shunt Signal Position Light Type FRP complete as per RDSO Specification 50 RDSO/SPN/194/2006/Rev.2.0 or latest with Off set bracket 3-1/2" to be fitted on 140 mm post drawing No.SA23840(Adv) Alt-2 for dependent type complete with signal unit bracket, terminals etc without lenses, lamp, lamp holder, and to suit LED signal lamps.

Supply of "Calling On" Signal Unit in FRP body without lenses and transformers as per RDSO Specification RDSO/SPN/194/2006/Rev. 2.0 or latest complete and to suit LED signal Lamps

Supply and Fixing of RE Protective Screens of expanded metal 12 SWG of size 1200 x 1500 mm on signals as per extent practice & as per instruction of Rly engineer at site DRG - No.SK-

Supply of Phenolic 10mm thick sheet, grade P3 in standard size of 1.22x1.22 Mtr as per spec. No. IS 2036 of 1995.

Supply of ARA Terminal blocks with links made of PBT Specn No.IRS/75/2006 (Rev - 2) with latest amendments and RDSO Drg.No.SA-23741A Alt.4., SA-23745 Alt.5, SA-23746, SA-23748 Alt.4, & SA-23756 Alt.3.

Supply of cartridge fuse block made of PBT as per RDSO Drg No SA-23748 Alt 4, SA- 23749 & Spec No.IRS S 75/2006 Rev.02 with latest amendment. Fuse block shall be suitable for round head type voltage fuses.

Supply of round head type non detoriating type low voltage cartridge fuse as per specn No. IRS/S/78/92 with latest amendments - 2A/4A/6A capacity

Supply of Tik-tak, piano type switches, 5 A (as per IS Specification).

Supply of three pole plug and socket 5 Amp (as per IS Specification).

Supply of earth electrode assembly as per Drg.No.CR/S&T/SK-815

Supply of UL listed long life Maintenance Free Earthing with constant performance service warranty. UL lisyted. 250 Micron with ALLTEC - Tera Fill TF 50 & TF-50 XT Back fill should RoHS & Low resisvity certified. The Back Fill having not more than 0.20 Ohm/cm resistance, eco friendly, non degradable and non soluble. The earthing pit shall be designed & supplied with Poly- plastic pit cover non conductive, environment friendly.

Supply and Installation of Lightening & Surge protection device, Single phase + neutral (housed in a suitable impact resistance box) for providing B class protection as per RDSO spec No. RDSO/SPN/165/2012 (Ver 3.0)

Supply and Installation of Lightening & Surge protection device, Single phase + neutral (housed in a suitable impact resistance box) for providing C class protection as per RDSO spec No. RDSO/SPN/165/2012 (Ver 3.0)

Maintenance Free Earth as per RDSO/SPN/197/2008 or latest consisting of : 1) Copper 63 bond steel electrode 3 Mtr long 17mm dia with copper bonding thickness of min. 250micron & UL listed & marked-01 No. (2) Earth enhancement compound RDSO Approved in sealed bag of 10 kgs - 03 No. (3) Copper strip 150 x 25 x 6mm - 02 No (4) Copper Strip 300 x 25 x 6mm- 01 No (5) 35 Sqmm Copper Cable to connect earth electrode to MEEB - 15Mtr Approx.

Supply of 35 Sq. mm. multistrand single core PVC insulated copper for connecting earth bus bar to earth electrode.

Supply of copper Tape 25x6 mm (Bonding ring conductor) mounted on insulated standoff (1 round).

Supply of B type choke to specn.No.IRS.S.65/83 (Amd.3 ) with latest amendments.

Supply of adjustable Track Feed Resistance disc type 7.5/15/30 ohms as per RDSO Drg. No. SA 20161-66/M (Adv) with latest amendments ( with phenolic moulded base).

Supply of Channel Pins single groove, galvanised, 7 mm suitable for 4mm dia bonding wire as per spec No. IRS: S 17-75 Revision 3.

Supply of Pre-wired Crank Handle cum key lock relay box (of metal) alongwith LEDs, with approved type push buttons, 8-way terminal strips, string rod, etc. as per Drawing No.RST.C.114

Supply of William stretcher nylong insulation set suitable for ground connection as per RDSO drg No T-10367, T-10368, T-10384 as applicable and to the spec IRS S 23/88 with Amendment No.01 & 40/84 with Amendment No.01 or latest amendments.

Supply of Tongue attachment nylon insulation set consisting of one inlsulating plate as per Drg no: RST-106961 & 3 nos of Ferrules with collars to suite rodding supplied as per RDSO spec & Drg.no: RST-10692

Supply of Gauge Tie Plate nylong insulation as per RDSO drg No: T-10372 Alt2, T- 10368, T-10371 Alt2, T-15083/88/Alt2 & T-11690/Alt2 and to the spec IRS S 23/88 with Amendment No.01 & 40/84 with Amendment No.01 or latest amendments.

Supply of GI bend pipe, B class, 50mm dia for cable entry in point machine alongwith required fixing arrangements as per standard practice on Central Railway. As per Drg No. RST.11835.

Supply of GI pipe, inner dia. 100mm dia. B-class as per spec. No.IS 1239 PT. 1/2004 or latest with sockets and fittings. TATA/JINDAL/ZENITH BIRLA make.

Supply of DIN Channel for the terminals 1 Mtrs each

Fuse terminals block with LED indication up to 2.5 sqmm screw type one in one out 76 (suitable for (400 mA, 630mA, 1 A, 1.6 A, 2 A, 4A, 6.3 A & 10 A ) as per RDSO SPN/189/2004 Ver.03 or latest . (without fuse)

Fuse links of (400 mA, 630mA, 1 A, 1.6 A, 2 A, 4A, 6.3 A & 10A)

Supply of Digital measuring wheel for measuring cable trench/route make: Stanley or Freemens make or similar reputed make.

Supply of Thermo-Shrink cable joining kit (Reinforced) TSF-2 type generally 79 confirming to RDSO specification RDSO/SPN/TC/57/2015 Rev 1 with modified kit contents as per CSTE's Specification No.:CR/SPN/TC/57 (A)/2015 Dt: 06.01.2015 (Table-A) to be suitable for jointing both 10/20/50 pair PIJF and 4/6 Quad cables alongwith sub-kit (Table-B) for armour continuity.

Supply of Electrically operated LIFTING BARRIER complete set without Hand Generator, Operating on 110V AC, with Boom length 9.76M along with one spare boom confirming to RDSO/SPN/208/2012 Ver.2.0 with amendment 1 or latest amendment.

Supply of Sliding Boom complete as per Central Railway practice Drg. No-SK-860 (1-

Supply of Paints as per relevant IS specification preferably Asian / Apcolite/ Dulux make in different colour in one kg/2 kg pack

Supply of Epoxy sets consisting of 3kg Gel coat red, 1 kg of thinner and 1kg of hardner. Set shall be of same make. Make: Dr Beck/ASTRAL/3M make.

Supply of Trans-receiver handheld 5 watt Analog VHF set along with two sets of OEM approved rechargeable battery including one as spare, quick Battery Charger, Helical Antenna and Belt Clip conforming to RDSO specification no.RDSO/SPN/TC/107/2018 Ver 2.1 or later.

Supply of 4.5 kg CPO2 type fire extinguisher along with all accesories, extinguisher 85 testing certificate has to be supplied along with - Supply of ISI marked Carbon Dioxide type (BC) fire extinguisher of 4.5 Kg capacity confirming to IS 2878: 2004 from seamless cylinder, with IS marked control value, high pressure mtr., Long discharge hose and horn complete with initial gas charged with carrying handle and wall mounting bracket etc. as required by site Engineer.

Supply, Installation, Testing & Commissioning of Microprocessor based intelligent, addressable, Fire Alarm control Panel with LCD display complying to RDSO/SPN/217/2025 Ver 3.1 or latest modular, 1 loop (minimum 125 detector/devices per loop-expandable to 2 loops) with 320 Character with soft keys for displaying alarm, events and operating functions, Day/Night operation 86 function, Remote maintenance service feature etc. The panel should be multi-protocol i.e. able to support at least 2 different makes of addressable detectors. The panel should have minimum two relay outputs & 1 Monitored Sounder Output. It should have provision to be connected to repeater panels in future. The panel shall capable to operate on 230 volts AC power supply, automatic battery charger, 24 volts, sealed lead acid maintenance free batteries sufficient for 24 hours normal working and then be capable of operating the system for 30 minutes during emergency condition. Panel should be Vds Certified. Above/

Excavation and Casting of main signal foundation as per Drg No SK 801 with 01 contractor's own materials including cement and anchor bolts of standard size. The required scaffolding Ferma etc for casting of foundation will have to be brought by the contractor at his own cost.

Erection of CLS post with surface base and signal unit on top or on OFF set Bracket, 02 fixing of front and back staging, ladder and guards, signal name plates/boards if any with contractors own brackets and fixing materials. This also includes erection of auxiliary signals like calling on, shunt signal if any. The work shall be done as per instructions of Rly engineer at site.

Hot dip Galvanizing as per RDSO Specn. ETI-OHE-13 (4/84) - signal post, OFF set Brackets dia 140 mm and length upto 5600 mm.

Hot dip Galvanizing as per RDSO Specn. ETI-OHE-13 (4/84) - Misc M.S. Fabricated items like point roddings, P/D brackets etc. length upto 1200 mm.

Fabrication and fixing of phenolic laminated/Fibre glass sheet in location box by 05 providing all fixtures as per Railway Drawing including fixing of PVC coated/with PVC pipe covered string rods at the back side for cable support with contractor's own materials. The work shall be done as per drg and arrangement similar to SK 783- 1& 2. with latest alterations & as per instructions of Rly engineer at site. a) Single Case

Fixing of cutting in relay bases & wiring of relays with Contractors own material obtained from approved sources in location box as per the instructions of Engineer in charge. Per

Fixing of ARA Terminals and fuse blocks on phenolic laminated sheets and fixing by stainless steel/brass nuts & bolts. This includes provision of two additional holes on the board on either side for cable conductor entry. Per

Termination of cable cores on ARA terminal/fuse blocks in the apparatus cases/ cable termination rack. This includes all associated works of pulling out the cable from underground. The work shall be done as per location plans and instructions of Rly engineer at site.

Excavation and Casting of Apparatus case foundation with contractors Anchor bolts, cement, ballast and other materials. The required scaffolding ferma etc for Casting of foundation will have to be brought by the contractor at his own cost. i) Single Case as per Drg No SK-803

Erection of Apparatus cases. This includes filling of location foundations and plastering .i)Single Case

Installation of earth electrode assembly as per Drg.No.RE/S&T/SIG/Tender/SK726/85 including earth wire connected through GI wire 8 SWG supported on M.S. flat of size 6mm x 40 mm to earth electrode as per drg. No.CR/S&T/SK-815 for sigg. Equipment such as lever frames, 11 apparatus case, signals, relay racks, block instruments, and etc. as per RE manual. The earth value should be less than 10 Ohms including the lead wire. The value should be measured in presence of Rly. supervisor. It should be documented and painted on earth enclosure made of concrete.( only earth electrode will be supplied by Railway). All other material required for provision of earthing will be brought by the contractor.

Fabrication, supply and fixing of various type of MS flat clamps on girder bridges/rocky area on GI pipes/its coupler as per drawing with requisite no. of nut and bolts as per site requirement and as per the instructions of Railway Engineer at site.

Installation, testing and commissioning of the Ring Earth as per RDSO specification 13 No.RDSO/SPN/197/2008 or latest amendment and RDSO drawing no.SDO/RDSO/E&B/001 and 002. All the consumables for mounting the copper tape/bus bar, copper lugs with stainless steel nut and bolts, copper bus bar etc. will be supplied by the contractor free of cost. Material to be procured from the RDSO approved vendor.

Installation of unit earth as per RDSO/SPN/197/ver I or latest, to construct earthing of </=1 Ohm consisting of a digging the earth to required depth, insertion of electrode, filling of earth 14 enhancing compound & construction of chamber, measurement of earth value and all other work of earthing as per code of practice. All the consumables for mounting the copper tape inside the relay room, Exothermic weld materials and tools & fixtures for the welding copper tapes nd Electrodes etc shall be arranged by the contractor.

Connecting main earth electrode to BRC using 35 sqmm copper cable.

Installation of 25x6 mm copper tape (bonding ring conductors) mounted on insulated standoffs (1 round).

Refixing of electrical point machine, ground connection during phase working (Non interlocked working) after removing the existing fitting if any, adjustment if necessary, cable termination, wiring, testing and commissioning of electrically operated point, fixing and connecting point indicator on derail switch if necessary. The work shall be done as per extant practice on C.Rly & the instruction of Rly engineer at site. Unit(PER T/O=1 set)

Fixing of point machine on newly laid turnout on Wooden/MBC sleepers, fixing of ground connections, adjustment and testing with crank handle operations, Removal of ground 18 connection & point machines duly numbered. This will include fixing of bend pipes with welded frame for cable entry to machine. This will also includes necessary adjustment and smithy work, drilling of holes to tounge rails, fitting of insulation for tounge attachment, gauge plate & stretcher bars, cable termination & wiring if required. The work shall be done as per extant practice on C.Rly & the instruction of Rly engineer at site. Unit(PER T/O=1 set)

Excavation of cable trench as per cable route plan, 1.0 mt. deep and 300mm wide along side the track in normal soil/strata, conforming to distances as per cable route plan and refilling after cable laying. This work includes covering of cable laid to trench by loose soil for a layer 19 of 50mm thickness after clearing of route, bushes etc. It shall be ensured that top of the cables laid is at a depth of 0.8 m or more. If it is less, then the width and depth shall be suitably increased and accordingly proportionate payment shall be made. In case depth of trench is not achievable due to site conditions, proportionate payment will be made as per procedure. The work shall be done as per extant practice on C.Rly & the instruction of Railway engineer at site. Drg No SK 805

Excavation of cable trench as per cable route plan, 1.0 mt. deep and 300mm wide along side the track in hard soil, conforming to distances as per cable route plan and refilling after cable laying. This work includes covering of cable laid to trench by loose soil for a layer of 50mm 20 thickness afer clearing of route, bushes etc. It shall be ensured that top of the cables laid is at a depth of 0.8 m or more. If it is less, then the width and depth shall be suitably increased and accordingly proportionate payment shall be made. In case depth of trench is not achievable due to site conditions, proportionate payment will be made as per procedure. The work shall be done as per extant practice on C.Rly & the instruction of Railway engineer at site. Drg No SK 805

Cutting of all types of Roads/platforms (except concrete type) for trenching and 21 excavation to depth of 300mmx300mm wide approx. and refilling after laying of RCC/GI/DWC pipe & to restore them to original condition. The work shall be done as per extant practice on C.Rly & the instruction of Railway engineer at site. Drg No SK 807

Fixing of GI pipes for crossing the culverts, bridges etc. and concreting of ends with brick masonry at both ends as per the instruction of Rly engineer at site.

Digging of trench 1.0 M deep from rail flange/road level (for LC) and, 0.3 Mtr to 0.6 23 Mtrs wide and back filling after placing of DWC/RCC/GI pipe. (Placing of DWC/RCC/GI pipe coverd separately). The ballast disturbed be screened and dressed as required by Engineer-in-charge or his representatives and road tarred immediately. Drg No SK 806

Laying of DWC/RCC pipes alongwith collars / RCC Half round pipes in trenches at places of track and road crossings, platform cutting etc.

Laying of signalling/Power/Telecom cable of various cores/sizes in trenches.

Laying of RCC Trunking and capping and sealing after cable laying as per std practice on C.Rly & the instruction of site engineer.

"Where ever depth of 0.5 m cable trench is not feasible, cable shall be protected as under:- Preparation of cement mixture 1:3:6 with contractor's own materials and spreading cement concrete mixture layer of 100 mm thick over the already laid cables in the excavated trench."

Laying of GI pipes in on bridges/culverts/concrete drain/ mountain ridges etc. with 28 suitable GI bend shall be provided where there is turning of pipe as per instructions of the site engineer. GI Clamps at every 2 m as shown in the drawing to be fixed. Suitable holes to be made in the pipe before laying as per instructions of the site engineer. 100 mm dia. Drg No SK 808

Releasing of cables from old location boxes and taking it into new location boxes. This includes excavating the earth to release the cables. From old location box for taking it into new location. This also includes releasing the old location box and bringing it to nearest station/central cabin. Location (old) will be released only after ensuring all working cables have been shifted in New location. Unit(Per location=1 set)

REMOVAL OF PSC/Wooden SLEEPERS coming in the way of/route of cable trenching, signal/Location foundation/Track Crossing etc. These obstruction will be removed by contractor for ensuring proper execution of related works.

REMOVAL OF Redundant/Old Rails coming in the way of/route of cable trenching, signal/Location foundation/Track Crossing etc. These obstruction will be removed by contractor for ensuring proper execution of related works.

FIXING OF "C" Channel Clamps on Girders along with proper coupling of GI/DWC 32 pipes. The work will be executed as per instruction of site incharge and site incharge may take decision as per site condition. All the fixures, nut bolts, tolls required to fix the channel will be provided by Contractor. Proper safety equipment like Helmet, Retroreflective jacket and whistle, flag is to be made available during execution of work.

Horizontal boring of cable duct of minimum 2.0 Mtr depth along with laying of 120mm HDPE pipe for track crossing with minimum depth reckoned from bottom of the rail/Road crossing with minimum depth reckoned from ground level. The work shall be done as per extant practice & 33 instructions of site engineer. Preparation of site for Horizontal Boring shall be carried out in presence o f Railway Representative. HDPE will be supplied by Railway. Note:- Contractor shall provide all material required for boring and adequate nos. of labours for proper laying of cables into the bore. Cable shall be laid cautiously so that it should not get damage due to rough handling & pressure on cable.

Termination of Tail cable inside the point machine through bend pipe this includes preparatory work of pulling the cables, and peeling out the insulation, dressing and lacing after 34 termination etc., pulling of tail cable as per circuit requirement inside point machine through bend pipe, termination of cables on terminal blocks as per instruction of site supervisor the cable shall be entered in such a way that, armouring shall protect the cable near sharp edge of entry point and armouring shall be clamped between pipe fixing bracket and boy of point machine.

"Patching work in old location box consisting 1) Digging of pit, cleaning of earth from 35 all sides, breaking of seal of location boxes removal of sand from location, marking of new cable holes. 2) insertion cable from ground 3) making place for cable termination in old location, shifting ARA, fuse etc after removal and termination including fixing of ARA. 4) Termination of cable in old location. 5) Filling of sand and plastering to all sides upto 50 mm below ground level."

Providing Road Breaker/concrete breaker/boulder or rock breaker with compressor & 36 Jack Hammer for Railway work such as cutting & dismantling of road concrete/Brick pucca structure (RCC/Steel section) including contractors fuel, driver and all other charges completed as directed by Engineer in charge

Painting two coats of synthetic enamel paint over one coat of primer on the following after scrapping and cleaning of the surface wherever necessary with contractor own supply of paints. 37 Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge. Epoxy will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer.(i)Apparatus Cases Full size.

Painting two coats of synthetic enamel paint over one coat of primer on the following after scrapping and cleaning of the surface wherever necessary with contractor own supply of paints. 38 Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge. Epoxy will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer.(ii)Apparatus Cases Half size.

Painting two coats of synthetic enamel paint over one coat of primer on the following 39 after scrapping and cleaning of the surface wherever necessary with contractor own supply of paints. Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge. Epoxy will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer.(iii)Main signal post with signal Units, Surface base and complete fittings as per Centre Railways standard practice.

Painting two coats of synthetic enamel paint over one coat of primer on the following after scrapping and cleaning of the surface wherever necessary with contractor own supply of paints. 40 Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge. Epoxy will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer.(iv)Shunt signal post with signal unit, surface base as per central Railway's Standard Practice.

Painting two coats of synthetic enamel paint over one coat of primer on the following after scrapping and cleaning of the surface wherever necessary with contractor own supply of paints. 41 Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge. Epoxy will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer.(v)Track lead Junction Box. (Black enamel outside only)

Painting two coats of synthetic enamel paint over one coat of primer on the following after scrapping and cleaning of the surface wherever necessary with contractor own supply of paints. Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- 42 charge. Epoxy will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer.(vi)Point Machine with ground connections complete (Point Machine with Black enamel only outside and ground connections with Red Oxide)

Painting two coats of synthetic enamel paint over one coat of primer on the following after scrapping and cleaning of the surface wherever necessary with contractor own supply of paints. 43 Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge. Epoxy will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer.(vii)Axle counter devices.

Lettering / Numbering of Signals, Point Machine, Track Lead junction Boxes, Block joints, Apparatus Cases etc.(each item to be taken as One Unit) This work will be carried out as per the standard practice being followed in Central Railway.

Excavation and casting of foundation for sliding Boom with contractor own material 45 including cement and another bolt of standard size. The required stop holding farma etc. for casting of foundation will have to be brought by the contractor at his own cost. The work shall be done as per instruction of Rly.Engineer at site.

Erection of sliding boom assembly right hand, left hand with fixures. All the materials, tools required for erection of the sliding boom will be arranged by the contractor. (As per central Railway standard practice) Above/

Item Breakup - C-SUPPLY & EXECUTION

Supply of polyolefin cable channel 2434 with Metre following dimensions, height (internal/external) 155/230mm x width 240mm/340 mm x length 1000mm with suitable detachable cover having fire protection class K1 in accordance with DIN 53438 part 2 and electrical characteristic Dielectric strength 48KV/cm in accordance with DIN VDE 0303-21 (As per annexure)for laying of all types of S&T cables.(Inspection Agency RITES)

Wheel sensor with protection tube of Numbers Frauscher make MSDAC type Rsr 180 (with BBIK- M 12 GS05 fixing along with cable length of 5 mtr (GS05). (Inspection Agency RDSO)

Wheel sensor with protection tube of Numbers Frauscher make MSDAC type Rsr 180 (with BBIK- M 12 GS05 fixing along with cable length of 10 mtr (GS05).(Inspection Agency RDSO)

SIC CARD FOR FRAUSCHER MSDAC ACS 2000. Numbers FRAUSCHER Make.(Inspection Agency RDSO)

"Supply of Axle counting Board ACB 120/ACB Numbers 130 type suitable for Frauscher MSDAC system as per RDSO Specification No. RDSO/SPN/176/2013(Version 3) or latest(Inspection Agency RDSO)"

"Power specification No. RDSO/SPN/176/2013 Ver.-3 & Manufacturers's Spec. or latest suitable with existing installations of MSDAC(Frauscher make)(Inspection Agency RDSO)"

"Input/Output Board IO-EXB, Part No. 20864 as Numbers per RDSO specification No. RDSO/SPN/176/2013 Ver.-3 & Manufacturers's Spec. or latest suitable with existing installations of MSDAC (Frauscher make) (Inspection Agency RDSO)"

IMC CARD FOR FRAUSCHER MSDAC ACS 2000. Numbers FRAUSCHER Make.(Inspection Agency RDSO)

Supply of Serial I/O card for Eldyne make Numbers MSDAC (Thales make) as per RDSO specification RDSO/SPN/176/2013 ver 3 & manufacturer specification (Part no 3 CR 01881RAA)2(Inspection Agency RDSO)

PARALLEL Card for Eldyne make MSDAC Numbers (Thales make) as per RDSO Specification No. RDSO/SPN/176/2005 or latest(Inspection Agency RDSO)

PDCU for Multi section digital axle counter Numbers (MSDAC) as per RDSO/SPN/176/2005 Make Eldyne electro System Pvt. Ltd. (Inspection Agency RDSO)

Supply of Analog card (AzLM) for Eldyne make Numbers Multi section digital Axle counter (MSDAC) as per RDSO/SPN/176/2013 or latest (Inspection Agency RDSO)

Motherboard 3CRo1838AAAA make Eldyne(Inspection Agency RDSO)

Track side Electronic Unit (EAK) for MSDAC as Numbers perRDSO Spec No.:RDSO/SPN/176/2013 Ver.- 3Make:ELDYNE only.(Inspection Agency RDSO) MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

Supply of STEU card suitable for MSDAC Numbers Siemens make. FIRMS OFFER MAKE / BRAND- SIEMENS(Inspection Agency RDSO)

"Block Input Output card (BLEA Card) for Numbers Siemens make MSDAC as per RDSO specification no.(Inspection Agency RDSO) RDSO/SPN/176/2013 Ver. 3.(Inspection Agency RDSO)"

SIRIUS CARD for Multi Section Digital Axle Numbers Counter Siemens make RDSO specification No.RDSO/SPN/176/2013 Ver.3 or latest Make/Brand: SIEMENS(Inspection Agency RDSO)

Processing and monitoring board (VAU CARD) Numbers for Siemens make Multi Section Digital Axle Counter as per RDSO specification No. RDSO/SPN/176/2013 ver.3.(Inspection Agency RDSO)

Supply of counting head ZP 43 V complete Numbers with sensor for Siemens make MSDAC(Inspection Agency RDSO)

Set of SK 30H double rail contact with 5.5 Numbers meter Cable for Multisection Digital Axle Counter, ( MSDAC) as per RDSO Spec. No. RDSO/SPN/176/2013 Make/ Eldyne Electro- systems Pvt Ltd. Version 3(Inspection Agency RDSO)

SK 30H double rail contact with 8 meter cable Numbers for Eldyne make Multi/Single section Digital axle counter as per RDSO specification no.RDSO/SPN/176/2013 ver.3 or latest and manufacturer specification. Make Eldyne electro systems Pvt.Ltd. (One no.packet contains the 02 no.TX and 02 nos RX Coils for rail connection sufficient for 1 DP including all accessories)(Inspection Agency RDSO)

Supply of AC & DC low current clampmeter Numbers with range 1 mA to 100 A or higher make FLUKE, RISHABH, or KOICO(Inspection Agency Consignee)

Supply Apollo,Agni,Series65 make or similar for fire alarm system.(Inspection Agency Consignee)

"Supply of octagonal booms 32 feet long Numbers suitable to HEIDZ make EOLB without hand generator as per RDSO SPEN no: RDSO/SPN/208/2012 with latest amendments. One boom have four pieces of 8 ft long(Inspection Agency Consignee)"

"Metravi 4 digit LCD display Auto ranging Numbers Digital Earth Resistance Meter Brand: Metravi (Detailed Description/Specification as per Product # 1 of GeM Contract No. GEMC- 511687740175436 dt.01/10/2025)(Inspection Agency Consignee)"

"Sanwa Model No. HG561H 7 range Low Numbers Voltage Insulation Tester with preset voltages of 15/25/50/100/125/250/500V. Auto AC/DC V selection and Continuity measurement function,. LED Level Meter for MOhms. IP30.OR SIMILAR (Inspection Agency Consignee)" MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

Casting of cement concrete to protectS&T cum equipments and laid cables, abovepipes etc by concrete mixture ofcement, sand, stone in the ratio of1:2:4 using 25 mm graded stoneaggregate as per instruction of site incharge of railways. Concrete is to becasted with the help of suitable sizeshuttering form as per siterequirement. Concrete is to be cured forsufficient time as per standard practiceson railways(Inspection Agency Consignee)

Industrial locker (Pigeon hold box) 12 Numbers Compartments. Made out of 18/19 gauge CR sheet with individual locking arrangement (1) size of locker 36 in Width) x 19 in (depth) x 6 foot (Height) (2) with 2 legs of each size 5 inch (H) x 3 inch (W) x 19 inch (D) (3) Size of each compartment 10.74 in (H) x 16.25 in (W) x 19 in (D) 2 in rows and 6 in columns with Siemens gray colour make.(Inspection Agency Consignee)

"Rechargeable LED head light with hand Numbers sensor, 500 Lumen power integrated with 3W COD flood light with 3.7V, 1000MAH lithium battery, Impact proof ABS, Black woven head band. Make: Groz , Model : LED/225 or Equivalent in Make : Fenix or Ledlenser or Olight or Petzl only Make/Brand:GROZ Firm's accepted offer-Accepted Make: Head Lamp Dual Mode and Hand Sensor, Model No.- LED- 225. Warranty: For Light warranty will be 12 Months from the date of delivery, and for Battery warranty will be 06 Months from the date of delivery. ,make/model-Groz, (Warranty Period : Upto 30 months from the date of delivery.)(Inspection Agency Consignee)"

Provision of covering of open areawith PPGI Numbers 2000.00 sheet (and sometransparent sheet also for betterlighting) of thickness 0.5 mm at theheight of 15 feet above the groundlevel with proper drain directingoutside the campus. Requiredsupporting steel structures & fixuresmust be provided by the contractor. (Inspection Agency-Consignee) (UNITNUMBER SHOULD BE READ AS PERSQ FEET(Inspection Agency Consignee)

Supply of in-built GNSS basedcable route Numbers tracer with 10W, 500mA, 85V transmitter suitable fordetecting & mapping undergroundcables with accuracy which canup to 3-5 cm or better, withcurrent direction up/down arrows,Remote calibration check feature.Supply shall include inbuilt RTKenabled receiver, transmitter,compatible dual Bluetoothandroid phone with RTK mobileapplication pre-installed inandroid device along withminimum 5 years subscription,compatible with NTRIP andRTCMv3.X messaging standardsand holder & standardaccessories. Make/Model: Radiodetection RD8200GS or similar." (Inspection Agency RITES)

Rechargeable Handheld Telecom TDR Cable Numbers Fault Locator ST-25 STANLEY OR SIMILAR (Inspection Agency Consignee)

" External DP Band Pass Filter Card suitable for Numbers MSDAC Siemens make.Make: SIEMENS(Inspection Agency RDSO)"

Broad Band Transformer suitable for MSDAC Numbers Siemens Make.(Inspection Agency RDSO) MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

Supply of Station master room cards (SMR) Numbers suitable for MSDAC Siemens.(Inspection Agency RDSO)

Supply of Station master key (SMK) suitable Numbers for MSDAC Siemens .(Inspection Agency RDSO)

ACR card for Siemens (Inspection Agency RDSO)

Digital Axle Counter spares Supply of MSDAC Numbers Spares - Siemens Make Scalance Switch(Inspection Agency RDSO)

Supply of MSDAC Spares- Siemens Make Numbers Process Connector.(Inspection Agency RDSO)

Supply of counting head ZP D 43 complete Numbers with sensor for Siemens make MSDAC(Inspection Agency RDSO)

Wheel detection sensor with 10 meter cable Numbers for Siemens MSDAC(Inspection Agency RDSO)

40V Cordless impact Wrench 3/4 (19mm) with Numbers eight types of sockets(Inspection Agency RDSO)

40 V Cordless Dust Blower(Inspection Agency Numbers RDSO)

Twist Adaptor 19mm weldon for 13 mm (part Numbers no. 210245FS(Inspection Agency Consignee)

Twist adaptor 19 mm Weldon for 7.2 mm (Part Numbers No: 210253FS)(Inspection Agency Consignee)

Twisted Drill size 13 x 19 mm (Part no. Numbers 5223118)(Inspection Agency Consignee)

Battrey oprated drill m/c cutter 22.5 mm Rail Numbers TCT Cutter 22.5x 55 mm (Part No: 240289) (Inspection Agency Consignee)

Hiring anddressingground/dismantlingstructures ,Removalof jungle, clearing ofearth, lowering highcess etc., along sidethe track between upand down linesobstructing drainagesof rain water, clearingof bushes obstructingvisibility at curvesand Level Crossingswith all lead and liftetc. complete and asdirected by theEngineer-in-charge.All labour, tools andplants consumablesstores includingsupply of JCB/Hitachiwith crew to beprovided by thecontractor at his owncost. The contractorshall arrange roadpermit for vehicle forall the States ofoperation, as perinstructions ofengineer in-chargeand vehicle shall notbe more than threeyears old. Paymentshall be made foractual working hoursat site.(Inspection Agency Consignee)

Battery operated High performance LED area Numbers with 3000 lumens output light weight & unbreakable as per specification attached (1) Product specification M18 HAL -+ M18 NRG 502B (2) Article No. 493345123 (3) Battery compatibility all Milwaukee M18 Batteries (4) Battery capacity (Ah) 5.0 (5) Battery type Li ion (6) No of Battery charger supplied 01 No. (7) Full Battey charging time 59 min (8) Max light output 3000/1500/650 (9) Max run time battery 2/4/9 hr. (10) No. of batteries supplied 2 Nos. (11) Voltage (AC) (V) 220-240 (12) Voltage (DC) (V) 18 (13 Wight with battery pack (kg) 3 (14) One year onsite warranty, installation & training free of cost mak Eibenstock/Milwaukee or equivalent. (Inspection Agency Consignee) MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

"Printing & Supply of various Signal Numbers 480.00 maintenance register paper size A-4, Thickness 70 GSM Minimum, 'A' Grade white paper 9 X 11"" size Both size printing Black colour with hard bound with top cover color printing having label, name, number of register etc.. Register would be contained total 200 Nos of pages on average. Register names, Format details are attached as annexure-A IN NIT (UNITNUMBER SHOULD BE READAS PER REGSITER) (Inspection Agency Consignee)"

High speed steel twist drill bit dia 7mm/13 mm Numbers 100.00 suitable for battery operated drill machine make Eibenstok. Drill bit make: MAKITA/BOSCH/FEIN or Other reputed brand(Inspection Agency Consignee)

MODEM SUITABLE FOR SIEMENS MAKE MSDAC Numbers SYSTEM TO WORK ON E1 & QUAD WITH AUTOMATIC BUMPLESS CHANGEOVER) Make- Efftronics,Siemens(Inspection Agency Consignee) Total 13860036.03