SPL REPAIR TO BLDG NO P-121 ( 01 TO 08) OR MD ACCN OF ENGR REGT AT DIPATOLI MIL STN UNDER GE DIPATOLI

Demolition of RCC in floors (other than ground floors beams,chajjas,lending slab and similar suspended works and removing all demolished material from the site and thrown away in low laying area up to distance 250 mtr as directed by the Engr-in-Charge.

Demolition of old RCC tank up to 1000 ltr capacity in any position and in any condition from the roof and removing all demolished material from the site and removing from site and thrown away in low laying area upto a distance 250 mtr as directed by Engr-in-Charge.

Demolition of brick work or rubbled stone masonry including all qoins arches , pillars etc built in cement mortar. Complete all as directed.

M &L for brickwork with fly ash modular bricks, strainght or curved on plan exc 6M mean radious radius built in Cement mortar 1:6 complete all as specified and directed.

Excavation in trenches n exc 1.5 m wide n exc 1.5 m deep in soft/ loose soil for foundation etc or for shaft, wells, manholes etc for laying cable,pole/stayers & stuts etc n exc 10 Sqm on plan and not exc 1.5 m in depth and getting out. complete all as directed.

Removing excavated material n.exc. 50m and depositing where directed at a level n.exc. 1.5 m above the starting point. All as directed.

Returning filling in including spreading leveling watering and well ramming in layers n.exc.25 cm. all as directed

M&L for precast reinforced cement concrete type B1, 1:2:4 using 20mm graded stone aggregate in cover slabs (for manholes etc), water (tank/drain) cover, shelves, landing and similar articles with plain faces incl necessary moulds and setting in CM 1:4 complete (reinforcement to be measured separately) all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to complete all as specified and directed.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.all as directed.

Roughening surfaces of old concrete floor by picking, sweeping, clean and washing down with water to remove dust etc complete all as specified and directed

Material and labour for brushing neat cement slurry with 3.0kg of cement per sqm including cleaning and washing and remove dust etc complete all as specified and directed

Material and Labour for 16mm to 18mm thick machine cut (table rubbed and polished) Granite of any type as in steps, jambs, pillars, cills, cooking platforms like in CM 1:4 including pointing with white cement mixed with admixture of pigment to match the shade of the slab complete including screed bed 15mm thick in CM 1:6 all as specified and as directed by Engr-in-Charge.

Rounding to edges of stone slabs on edge such as in steps cooking platform and other similar situations. Complete all as directed.

M&L for Non- skid colour ceramic tiles,7 to 8mm thick square / rectangular area of each tile exc 0.06 sqm but n exc 0.11sqm in floor over and including 15mm thick screed bed in CM (1:6), set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor complete all as specified and directed.

M&L for Non- skid colour ceramic tiles,7 to 8mm thick square / rectangular area of each tile exc 0.18 sqm but n exc 0.38sqm in floor over and including 15mm thick screed bed in CM (1:6), set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor complete all as specified and directed.

All as per Item No 16 here in- before but in skirting including 10mm thick screed bed in CM(1:4) completed all as specified and directed

M&L for coloured glazed ceramic tiles in vertical surface 350mmx250mmx7mm/450x350x7mm thick over and including 10 mm thick cement plaster in CM (1:4); set and jointed in neat cement slurry & pointed in white or coloured cement to match the surfaces complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 18-20 mm thick set over and including 15mm thick screed base in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with beewax polishing complete all as specified and as directed by Engr-in-Charge.

All as per item No-19 but here-in-before as in skirting over 10mm thick cement plaster in CM 1:4 complete all as specified and as directed by Engr-in-Charge.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.complete all as directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on wall of brick work or concrete surface, finished fair and even (with out using extra cement) all as specified and directed.

M&L for rendering 10 mm thick in cement mortar 1:6 on wall of brick work or concrete surface, finished fair and even (with out using extra cement) all as specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling of brick or concrete surface, finished even and smooth (with out using extra cement) all as specified and directed.

M&L for 1mm thick wall care putty on newly plastered or old plastered wall surfaces and rubbing smooth surface as directed by Engr-in-charge.

M&L for 1mm thick wall care putty on newly plastered or old undolated ceiling surfaces and rubbing smooth surface as directed by Engr-in-charge.

Complete removal of existing treatment and preparing the old surface of walls of any height of bldigs and apply two coat of cement base paint over a coat alkali resistant primer and as directed by Engr-in-Chare at site.

M&L for Preparation of new plastered or unplastered surfaces of wall and applying two coats of white or tinted cement based paint over a coat of primer complete all as directed and specified.

Complete removal of existing treatment or preparation of newly/old plastered wall surfaces, chajja, facia etc and applying two coat weather proof exterior emulsion paint(1st quality)/plastic emulsion paint on walls, chajjas,facia by mechanical applicator of any height of bldigs etc , including primer complete all as specified and as directed .(Weather Coat shall be of Asian paint, Apex ,ultima or equivalent as approved by GE)

M&L for preparing new plastered surfaces and applying two coats of distember oil emulsion white or tinted after one coat of white primer complete all as specified and directed.

M&L for preparing of old surfaces, washing, rubbing down and stopping of disstempered and painted surfaces and applying two coats of distember oil emulsion on wall complete all as specified and directed.

M&L for preparation of new surfaces and applying three coat of white wash on ceiling including cornices etc complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old ceiling surfaces and applying two coat of white wash complete all as specified and directed by Engr-in-Charge.

S&F powder coated Aluminium three track sliding glazed window manufactured with approved aluminium section with three sliding shutters each shutter width one half of the length of window with the following specifiecation and making good the adjascent surfaces :- (a) Window frame of cross section 101mmx40mmx1.5mm thick. (b) Three way track for smooth slding shutters of cross sections 91.80mmx31.75mmx1.1mm thick. (c) Sliding shutter frame of cross section 40x18x1mm. (d) Aluminium glazing stip of size 18.2x16.66mm. (e) 4mm thick flat glass superior quality for two shutter. (f) IDPE rubber gasket for fixing glass. (g) Locking cleat/device as shutter 01 Nos. (h) 02 Nos sliding roller per shutters. (j) aluminium wire cloth 0.36mm stainless steel nominal dia of wire and average width of aperature 1.40mm for one shutter. (k) Fixing screws for frame with wall 06 per window with fancy design. (Note: Window will be measured outer to outer frame and no extra to be paid.)

S & F powder coated anodised alm ventilator louvre type with two separate frame of size 50.5mmx40mmx1.5mm thick (01x frame for fixing of 4mm thick coloured glass & 01x frame for fixing 4mm tk figured glass) powder coated anodised aluminium section weighing 0.55 kg/m including 4mm thick figured glass, SS wire mesh and necessary joining cleats, glazing clips, rubber packing, side handles fixed to wall with fastener etc, complete all as specified & directed.

S&F Powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weeighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fitings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 no.) suitable handle (1 no.) and incl 4mm thick flat glass superior quality for one shutter, aluminium wire cloth 0.36mm stainless steel nominal dia of wire and average width of aperature 1.40mm for one shutter complete all as specified and directed.

S&F powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from frames) not exc. 1.5 sq. m each, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from frames) exc. 1.5 & n exc 4 sq. m each, complete all as specified and directed.

Taking down shutters of any description exc 1 but n exc 2 sq. m each, complete all as specified and directed.

S&F pressed steel frames for doors of size 125x60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

S&F pressed steel frames of size 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and as directed by Engr-in-Charge.

M&L for factory made glazed and skeleton shutters 35 mm thick open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chemfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.20 (a); for doors supplied and fitted to chowkats complete all as specified and directed.

S&F factory made 35mm Flush shutters(ISI Marked) solid core construction, with block board core and plywood, commercial type on both sides complete all as specified and as directed by Engr-in-Charge.

M&L for dismantling boarding, any description, fixed in any position with nails. Complete all as specified and directed.

M&L for prelaminated particle board 18/19 mm thick interior grade , prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screw to timber frame work framed work as in cupboard.incl. leaping all around.Complete all as specified and directed

S&F Hasp & staple ,75mm, Aluminium anodised incl bolt to hinge plate and fixed with screws for cupboard.Complete all as specified and directed

S&F Continious (piano) hinges, mild steel, bright finish or elecrogalvenised, 30 mm width of flaps(when open) .Complete all as specified and directed

S&F Solid PVC Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined to gether with solvent cement, suppling & fixing in the frame as per specification & drawing complete all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average with of aperture 1.18mm and fixed with tinned tack, or galvanised wire staples .Complete all as specified and directed

S&F Aluminium anodised barrel tower bolt 150mm long.

S&F Aluminium anodised barrel tower bolt 200mm long.

S&F Aluminium alloy, anodised sliding door bolt of size 250mm with hasp and staple and fixing clips of sheet.

S&F Aluminium alloy,anodised handle cast type of size 150mm

S&F SS Butt hinges medium weight 100mm size,cold rolled mild steel.

S&F Ordinary rat tail rod pattern, 300mm spring incl roller and roller plate complete.

Taking down GI tubing and connection including removing to store of 15mm dia complete aall as secified and directed

Taking down GI tubing and connection including removing to store of 20mm dia complete aall as secified and directed

Supplied and fixed GI tubing 15 mm bore medium grade with all fittings fixed to walls and ceilings or laid in floors all as specified and directed

Fixing only GI tubing 15 mm bore medium grade with all fittings fixed to walls and ceilings or laid in floors all as specified and directed

Supplied and fixed GI tubing 20 mm bore medium grade with all fittings fixed to walls and ceilings or laid in floors all as specified and directed

Fixing only GI tubing 20 mm bore medium grade with all fittings fixed to walls and ceilings or laid in floors all as specified and directed

S&F in repair Gun-metal, globe or gate valves 15mm dia with iron wheel head, screwed both ends for iron pipe and fixed.

S&F in repair Gun-metal, globe or gate valves 20mm dia with iron wheel head, screwed both ends for iron pipe and fixed.

Dismantling water tanks and removing exc 250 & nexc 500 ltrs capecity complete all as specified and as directed by Engr-in-Charge.

S&F PVC rotational moulded polythylene water storage tanks 500 litres capacity incl cover etc complete all as specified and as directed by Engr-in-Charge.

Disconnecting exisiting tanks setting aside for repairng cleaning and removing al scale and dirt etc from mounths of circulating pipes etc and including refixing in existing position with all fittings, capacity of tanks exc 250 ltrs and not exc 500 ltrs complete all as specified and as directed by Engr-in-Charge.

S&F in repair 15mm dia bore, stop valve (concealed type), cast copper alloy fancy type chromium plated screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in pipe and all as specified and directed by Engineer-in-Charge.

S&F in repair 15mm, stop valve/angle valve, cast copper alloy fancy type chromium plasted with long shank and cup screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed of size 15mm bore with fancy design and all as specified and directed by Engr-in-Charge.

S&F in repairs bib taps fancy type, cast copper alloy chromium plated 15mm bore with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule and all as specified and directed.

Supplied and fixed in repair 125 mm size brass chormium plated shower rose including fixing to steel pipe or union complete all as specified.

Supply and fix in repair, sinks with drainage board made of stainless steel 1 mm thick sheet for, kitchen or laboratory with plugs, washers and waste pipe; cast iron cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed by Engr-in-Charge.

Fixing only in repairs sinks with drainage board made of stainless steel 1 mm thick sheet for, kitchen or laboratory with plugs, washers and waste pipe; including beading in cement mortar on to wall or including fixing cantilever brackets and connectin union to waste pipe etc, complete all as specified and as directed by Engr-in-Charge.

S& Fix utensil rack/kitchen rack stainless steel size 850xmmx800mmx270mm as approved make and fixed to wall and as specified and directed by Engineer-in-Charge at site.

S& Fix in repairs soap dish, any type fixed to plug with chromium plated brass screws

S&F Chromium plated tubular towel rail, 20mm dia, D type 60 cm long between flanges.

S&F in repairs decorative curtain rod made out of 25mm dia (outer dia) MS pipe having wall thickness 0.63mm, PVC coated of any colour and pattern as approved overall dia 28 to 28mm, includiing and including two nos brackets on each ends alongwith globe on each ends for earch window/door fro fixing complete all as specified and directed with fancy design and approved by engineer-in-Charge.

S&F in repairs PVC valveless syphonic action fancy type low level flushing cistern 10 ltr. Capacity of approved incl flush pipe of 32mm bore and all as specified and directed.

Supply and fixing in repair vitreous china squatting pan 'Orrisa pattern' size 580x440mm white with integral foot rests any pattern including provn of lime concrete bedding and making connection with & including PVC P Trap, etc complete all as specified and directed.

Supplied and fixed in repair vitreous china WHB white flat back size 550x400mm including Supplied and fixed angle iron brackets, C.P pillar tap fency type 01 No 15mm bore, CP waste coupling, 32mm dia and PVC waste pipe 32mm dia and PVC connection 450mm long high pressure complete all as specified & directed.

Demolition and breaking up 150/160mm dia drain pipes (salt glazed ware, AC or reinforced concrete or PE, DWC (Double wall corrugated pipes) set in cement mortar complete all as directed

S & F ultra plus PE, DWC ( Double Wall corrugated ) pipes confirming IS-16098 Part - 2 : 2013 pertaining structured wall plastics pining system for Non - pressure drainage and sewerage 150 mm bore pipe and fittings with non smooth surface, type B complete all as specified and directed.

M&L for cement concrete bed to drain pipes including packing under ,hounching against the side of pipes after they are laid and tested in PCC (1:4:8) type D-2 for 100 to 150mm dia (RCC/PVC/DWP/SGR etc) pipe complete all as specified and directed

Taking down eaves gutters and rain water pipes (any ize or patterns) including all heads,shoes,bends,swan-necks etc. Complete all as specified and directed

S&F PVC(SWR) floor trap 75mm dia plain with grating incl jointing with solvent cement.

S&F PVC(SWR) pipe 110 mm dia single socketed in any length with rubber ring joints, fixed to wall with and including stack and clamp.

M&L for PVC (SWR) bend of radius 110mm dia

M&L for PVC(SWR) Tee of radius 110mm dia

M&L for PVC (SWR) vent cowl 110mm dia

M&L for PVC(SWR) pipes 75mm dia single socketed, in any length with rubber ring joints,laid in trenches or fixed to wall with and including stack and clamp.

M&L for PVC (SWR) bend of radius 75mm dia

Demolition of cement concrete in ground floors and paving exc 15cm thickness(below or above ground level) all as directed.

M&L for cement concrete 1:5:10 type E-2 (using 40 mm graded stone aggregate as in filling around shunken areas complete all as specified and directed.

M&L for 40 mm thick PCC (1:2:4) type B-1 using 20 mm graded stone aggregate with WPC as in sunken portion and making adequate slope toward spout pipe complete all as specified and as directed. NOTE: - Water Proofing Compound shall be measured and paid separately

M&L for rendering 15 mm thick on concrete or brick surface in CM (1:3) mixed with WPC as per manufacturer instructions and finishes surfaces even and smooth with out using extra cement.Complete all as specified and directed Note - WPC will be measured and paid separtely

M&L for applying two coats evenly a tack coat of hot air blown bitumen of grade 85/25 @ 1.50 Kg per sqm per coat (one coat over plaster and one coat on polythene film) including cleaning of surface over polythene film complete all as specified and as directed

M&L for polythene film black 200 micron thick laid in floor, vertical surface etc complete all as specified and directed.

S&F M.S framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or FE 310-0 complete all as specified & directed

Complete removal of existing roof treatment from RCC roof including old hussion felt & preparation of surface with bire brush and cleaning with water complete and M&L for water proofing treatment on non approachable / accessible roof surface horizontal and vertical surfaces in following sequence through manufacturer / authorized applicator of the manufacturer complete all as specified and directed :- (a) Brushing neat cement slurry @ 3Kg per Sqm on roof slab. (b) 15 mm thick cement plaster fair finished using cement mortar (1:4) with WPC on roof slab. (c) Applying oil based bitumen primer @ 0.30 ltr/Sqm on plastered surface. (d) Applying modified APP polymeric membrane 3mm thick and minimum weight 3.00 Kg / Sqm for water proofing of roof , sealing as directed at site with 100 mm over laps as per manufacture's instruction. Note : Supply only WPC shall be measured and paid separately under relevant item.

M & L for providing cement concrete type B1 1:2:4(20 mm graded stone aggregate) as in lintels upto 1.5m clear span, copings, bed plates (block),cills, steps and other bands, parapet and railing upto 60cm height. complete all as specified & directed..

M&L for 22 mm thick machine pressed & polished‘ cement concrete tiles with grey cement without pigment of size 250 mm x 250 mm laid in neat cement slurry over and including 15 mm thick bed screed in CM 1:4 mixed with chemical compound PIDIPROOF LW of DR FIXIT of PIDILITE INDUSTRIES LTD 200 milli - litre mixed with 50 Kg of cement or STP No 1 (LIQUID) of STP LTD in proportion 200 milli litre per 50 Kg cement,as per manufactures instructions and tiles properly laid with 3 mm wide joints filled with FEVIMATE TG of DR FIXIT of PIDILITE INDUSTRIES LTD or TILE GLUE of STP LTD as per manufactures instructions complete all as specified and directed by Engr- in - charge.

M&L for applying two coats aluminium paint over bituminous surface of membrane. Complete all as specified and directed

M&L for repair and rendering 10mm thick in cm 1 :3 on chajjas, facia, roof projection, column sides, beam bottom and sides including throating after removing cracked plaster and concrete including cleaning of viisible reinforcement and treating with cement slurry also necessary repair to cracked concrete if any with cement concrete 1:2:4 Type B-0 using 12.5mm graded aggregate including necessary scafolding work for double/single storey bldgs all as directed .

M&L for 75 mm thick PCC 1:3:6 Type C-2 using 20mm graded aggregate as in plinth protection etc, laid to slope of 1:12 and shall be laid in alternate bays n.exc 1.5 m in length, joints 20mm wide will be provided every 1.5m and filled with ceiling compound grade ‘A’ the joints between external wall and plinth protection shall also be laid with ceiling compound grade ’A’, finished cement concrete surface even and smooth all as specified.

M&L for PCC 1:2:4 type B1 20mm grade stone aggregate as in padding, hold fasts/filling of chowkhats or similar work complete all as specified and as directed by Engr-in-Charge.

Supply only liquid water proofing compound.ISI Marked

M/L for preparing the new surface of any description not otherwise described over 10 cm width or girth on steel surface and applying 02xcoats of synthetic enamel paint over one coat of red oxide primer all as specified

M&L for preparing the old steel surface of any description not otherwise described over 10 cm width or girth and applying one coats of synthetic enamel paint all as specified and directed

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified & directed.

M&L for applying two coats of synthetic enameled paint on old painted wooden surfaces of any description not otherwise described over 10cm width or girth including preparation of surface all as specified and directed.

M&L for cement concrete in ground or above ground floors 40mm thick over sub base (1:2:4) type B1 using 20mm graded aggregate finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

M&L for chequered cement concrete tiles with grey cement and no pigment 30cmx30cmx25mm thick over 15mm thick screed bed in CM 1:6 set jointed and pointed in neat cement slurry in floors complete all as specified and as directed by Engr-in-Charge.

S&F M.S rolled mild steel joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc (cut to ordinary lengths i.e. within 20 mm of the length indicated) conforming to Fe 410-W- (Gde-E-250) quality-A.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safecustody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. etc complete all as directed.

Taking down carefully copper/aluminium sub main wiring of size 2.5/4/6 sqmm from surface/concealed at any height and removing the materials from site and making good the disturbed surfaces of walls,floors roofs etc complete all as directed.

Taking down Old/ Unserviceable MCB DBs SPN/ TPN Main Switches by disconnection of electric connection including old unsv MCCBs,MCBs, isolators etc and making good to distrubed surface complete all as directed.

M&L for point wiring for One light/Fan point controlled by one five amps one way single pole switch complete with 1.5 sqmm , single core , multi stranded copper conductor PVC insulated and unsheathed FRLS cable 1100 Volts grade , drawn through PVC concealed conduit 20/25 mm dia on wall/ceiling ,including replacement by new 3 mm thick phenolic laminated sheet top covers and sunk type CI/steel terminal boxes ,cromium plate screw as suitable size for mounting of switch & scoket including 1.5 sqmm size pvc insulated unsheathed copper conductor to common earth and connecting to earth dolly complete all as specified and directed. Note: The rate quoted is deemed to be included for Penolic sheet (Hylem) and steel terminal box , cutting of hylem sheet for fixing of switch and scoket including cutting chases in wall making good to disturbed surface and matching with existing surfaces.

All as per Ser item No 120 here-in-before but one 3 Pin Socket out let 5 Amps on the same board.

All as per Ser item No 120 here-in-before but one 3 Pin Socket out let 5 Amps on the independent board.

All as per Ser item No 120 here-in-before but one bell/buzzer point controlled by one push button on the independent board.

All as per Ser item No.120 here - in - before but one light point controlled by two 2 - way switches,with wire 1.5 Sqmm size

All as per Ser item No 120 here-in-before but point wiring with 2.5 sqmm for 15 Amp socket out let & provision of earth wire 2.5 sqmm connected to common eart dolly.

S&F Switch Piano type 2 way switch 16 amp 230 v complete all as specified and directed at Site.

Supply and fix Switch Piano type, single pole, one way 5 Amp complete all as specified & directed.

S&F Switch piano type , single pole , one way 15 Amps complete all as specified and directed.

S&F Socket out let 2-in-1 2/3 pin 5 Amps complete all as specified and directed.

S&F Socket outlet 2-in-1, 3 pin ,5 and 15 amps , flush type complete all as specified & directed.

S&F in replacement electric Bell, ding dong type AC 230 Volt single pole complete all as specified & directed at site.

S&F in replacement Bell push 5 Amps for electric Bell/Buzzer, AC 230 Volt single pole complete all as specified & directed.

S&F Ceiling rose, 3 terminal PVC/polycarbonate complete all as specified and directed.

S&F electronic regulator step type 230 Volts single phase 120 watt complete all as specified and directed at site.

M&L for lamp holder , PVC /Polycarbonate type with back plate suitabl for batten fittings complete all as specified and directed at site.

M&L for submain complete with 2x4 sqmm, single core, multi stranded copper conductor , PVC insulated and unsheathed FRLS cable 1100 Volts grade, drawn in with and including PVC concealed conduit 20/25 mm dia as per site requirement along walls/ceiling etc including 1x4 sqmm size pvc insulated unsheathed copper earth continuity conductor to common earth and connecting to earth dolly complete all as specified and as directed. Note:- (i) all three wire(Phase red colour,neutral black colour and earth wire green colour) should be run through for each individual circuit from the DBs (ii) painting over surface conduit to be done to match with walls/ceiling existing surfaces. (iii) Two run of wire (phase & neutral) and one run of wire (earth conductor) be measured as one length)

All as per ser item No-136 here-in-before but 2X 6 Sqmm and 1X 6.0 Sqmm for Earth wire

Supply and fix MCB DB SPN 8 way double door with metal door suitable for housing of MCBs grouting/flush in wall and making good to disturbed surfaces incl fixing material/accessories complete all as specified and directed at site.

Supply and fix MCCB DB VTPN 4 way with metal door suitable for Provision of incommer as MCCB and out going MCBs grouting/flush in wall and making good to disturbed surfaces incl fixing material/accessories complete all as specified and directed.

Supply and fix in replacement MCCB 100 Amp 415 volts 16kA 4 pole complete all as specified and directed at site.

S&F MCB SP( 6 to 32) Amp 240 volt 'C' curve complete all as directed and specified by Engineer in charge.

S & F in replacement of 240V, 10KA MCB SPN 40 Amps "C" Series fixing in DBs, connecting with bottle type copper thimbles complete all as specified and as directed by Engineer in charge.

S&F in replacement of isolator DP 63 Amps 'C' Series fixing in DBs, connecting with bottel type copper thimbles complete all as specified and directed.

S&F in replacement of LED tube light fitting 20 watt 230 Volt LED Lighting with polycarbonate housing & integrated electronic driver, including all internally pre-wired and inncluding connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed at site.

S&F in replacement of environmental friendly, ultra modern, energy saving, surface mounted, decorative oval plastic bulk head LED light fittings 10 watt capacity ,comprising of high brightness LEDs, IP54 protection complete with all accessories internally pre-wired and inncluding connecting up with 2/3 core twisted flexible copper conductor cable with suitable size of flexible PVC/steel Conduit complete all as specified and directed at site.

M&L for rewinding repair and greshing of ceiling fan of any size sweep single phase. Ceiling fan of any size opening from any height or any locations, fan opening from hook, clamp & refixing the same after cleaning and greshing with required necessary cutting/welding/granding job or required store such as nuts, bolts, washer and suitable length mild steel/ down rod duly making holes etc complete as specified and directed.

S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer- in-charge.

S & F for Highly efficient LED Bulbs, 9 W, used as a ready replacement for existing Old UNSV bulb lamp complete all as specified and directed by Engineer in charge

S&F in replacement PVC ventilating air fan single phase 300 mm sweep complete with louver shutter and including making of hole suitable size fan base after cutting of brick/stone wall /suitable size of water proof ply wood complete all as specified and directed.

Supply, Laying on replacement ,connecting, testing and commissioning of XLPE LT UG cable of size 35 sqmm 3 1/2 core PVC insulated and sheathed armoured heavy duty cable 1100 V grade with alu conductor cable all as directed.

Supply and lay burnt bricks sub class ‘B’ old size laid dry in trenches across the cable protection all as specified and as directed

M &L for GI Earthing complete with GI earth plate electrode 60cm x 60cm x6 mm buried directly in ground verticvally to size of earth pit not less than 0.90x 0.90 x 2.25 mtr below ground level with top edge of the plate at a depth not less than 1.5 mtr below ground level, earth plate connected to galvanised earth strip of size 32 x 6 mm, 7.5 mtr long (Min) by means of brazing nuts, bolts, check nuts, & washers ,testing of completion (drawn in earth strip protection pipe light gade GI of size 40 mm dia) by means brazing at both edges with vertical plane of electrode all as shown in plate No 3 of SSR Part - I filling with charcoal dust , and common salt , including necessary excavation and earth work in any type of soil ,perforated watering pipeof size 15 mm dia,funnel with wire mesh,earth strip protection pipe light grade PCC chamber 1:3:6 type C1 (for even finish on both the faces) and RCC cover 1:2:4 Type B1,450 x450 x50 mm thick with 6 mm dia CTD bars 150 mm c/c with 2 Nos of handles of 10 mm dia steel rod all as specified and directed and testing on completion and connected to equipment with lugs and screw nuts etc all as specified and directed by EIC Note : (i) 7.5 RM GI earth wire deemed to be included in quoted rates beyond 7.5 RM wire shall be measured and paid separately. (ii) Earth resistance of earth pit should be not more than 02 Ohms on testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost. (iii) Rate quoted by the tenderer is deemed to included salt & Charcoal upto & above 450 mm (Min) top of GI Plate.