CA NO GE(W)/HSR-67/2024-25 REPAIR/REPLACEMENT OF FENCING ROLLING SHUTTER and STEEL GATE OF ZONE B AT HISAR MIL STN UNDER GE (W) HISAR

Amount

Dismantling posts or struts embedded in soil/ RCC (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed.

Dismantling fencing wire mesh, any type complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Surface dressing n ecx 15 cm deep in soft/loose soil complete all as specified and directed.

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, and removing surplus soil to a distance n.exc 50 m in soft/ loose soil complete all as specified and directed.

Removal of excavated soil to a distance exc 5 KM upto a total distance of 15 KM or outside MD Land complete all as specified and directed.

M&L PCC 1:3:6 type C2 using 40 mm graded stone aggregate in foundations, filling and mass complete all as specified and directed.

S&F MS work in posts and struts in fencing including cutting tops to shape as directed, drilling holes notching for wire etc, flat iron fillets for securing wire mesh including all necessary drilling, bolting or riveting etc, and similar work conforming to Fe290 Gde E-165 complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed.

Supply only Chain link MS galvanisd fencing, any size or type complete all as specified and directed.

M&L preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of black japan paint over a coat of red oxide primer complete all as specified and directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm but n exc 10cm long Dia meter of Shank 5 to 10 mm complete all as specified and directed.

M&L mild steel round bars 10mm dia and over, cut to length, bent to shape required, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality conforming to Gde E-165 (Fe-290) complete all as specified and directed.

M&L preparation of new steel surfaces of any description n exc 10cm width or girth when unconnected with other painting or when painted in different tintotherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted steel or iron surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for Framed work such as for portions framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc.grills, gratings, etc.. with ends of bars houldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintl hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for running welding in repairs exc 6 cm but not exc 9 cm complete all as specified and as directed.

S&F 1.25 mm thick Steel rolling shutters, with ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, with safety lever locks mild steel with 4 levers for rolling shutters gear operated type with bevel gear box and crank handle complete all as specified and as directed.

Taking down top cover of rolling shutter and refix the same, Area of rolling shutter is exc 05 sqm but n.exc 10 sqm to carryout greasing, oiling, repair of damage laths & hinges, spring,pully , ms shaft, bearing etc,straighting of steel member if requird, welding if any required, changing of any damge part required for proper functioning of rolling shutter including to carry out one coat of synthetic enalmal paint and preparation of steel surface complete all as specified and directed. Note:-(i) Any part of rolling shutter if required be changed shall be measured and paid seperately under relevent item.

Taking down top cover of rolling shutter and refix the same, Area of rolling shutter is exc 10 sqm but n.exc 15 sqm to carryout greasing, oiling, repair of damage laths & hinges, spring,pully , MS shaft, bearing etc,straighting of steel member if requird, welding if any required, changing of any damge part required for proper functioning of rolling shutter including to carry out one coat of synthetic enalmal paint and preparation of steel surface complete all as specified and directed. Note:-(i) Any part of steel rolling shutter if required shall be measured and paid seperately under relevent item.

Taking down top cover of rolling shutter and refix the same, Area of rolling shutter is exc 15 sqm but n.exc 20 sqm to carryout greasing, oiling, repair of damage laths & hinges, spring,pully , MS shaft, bearing etc,straighting of steel member if requird, welding if any required, changing of any damge part required for proper functioning of rolling shutter including to carry out one coat of synthetic enalmal paint and preparation of steel surface complete all as specified and directed. Note:-(i) Any part of steel gate/door if required be changed shall be measured and paid seperately under relevent item.

Taking down top cover and rolling shutter and refix the same of any size and patteren, to carryout greasing, oiling, repair of damage laths & hinges, spring,pully , MS shaft, bearing etc, straighting of steel member if requird, welding if any required, changing of any damge part required for proper functioning of rolling shutter including to carry out one coat of synthetic enalmal paint and preparation of steel surface complete all as specified and directed. Note:-(i) Any part of steel gate/door if required be changed shall be measured and paid seperately under relevent item.

Supply only Ball bearing for rolling shutters of any size complete all as spcefied and directed.

Supply only MS pipe 50mm dia for rolling shutters of any size complete all as spcefied and directed.

Supply only MS pully suitable for rolling shutter of any size complete all as spcefied and directed.

Supply only MS gear box suitable for rolling shutter of any size complete all as spcefied and directed.

Supply only MS Spring suitable for rolling shutter of any size complete all as spcefied and directed.

Supply only MS sliding lock suitable for rolling shutter of any size complete all as spcefied and directed.

M&L, 15mm thick rendering in CM 1:4 to brick/concrete wall surfaces trowelled to even & smooth with out using extra cement including taking down old cement plaster complete all as specified and directed.

M&L for Rough cast plaster with rough mixture consisting of crushed stone or fine gravel agg, size 6 to 12mm mixed with course sand and cement in the ratio of 1:1:1 shall be applied and finished even on external wall including taking down old cement plaster complete all as specified and directed.

M & L two coat of cement base paint on new surfaces of walls including preparation of surfaces complete all as specified and directed.

M & L one coat of cement base paint on old surfaces of walls including preparation of surfaces completeall as specified and directed.

S&F 16 to 18mm thick Dholpur stone cladding gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.25 sqm area and not exceeding 0.5 sqm fixed with 15mm thick cement ans stone dust mortar, recess pointed(10mmx20mm) and with admixture of white cement and dholpur stone dust (1:1) using adhesive and including one number SS clamps (grade -202) of flat 30mm X 2mm,150mm long made to shape in each slab,making V groove at top and bottom of stone and drilling hole for hold fastener,polishing, rubbing & including silicon treatment complete all as specified and directed. Note : Work shall be carried out in portionof building up to three storey hence necessary scaffolding an safety measures required to support adjacent portions of site are deemed to be included in quoted rates

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over old surfaces including complete removal of existing treatment complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

S&F fastners 100 mm length complete all as specified and directed.

M&L for 75 mm thick PCC (1:4:8) using 40 mm graded stone aggregate as in sub base of floor finishes complete all as specified and directed.

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand or cement concrete type B-0, 1:2:4 (12.50 mm graded aggregate) as in packing and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. lai bedded and jointed in any mortar complete all as specified and directed.

M&L for Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and no pigments complete all as specified and as directed.

M&L for 100 mm thick cement concrete type B- 2, 1:2:4 (40mm graded aggregate) complete all as specified and as directed.

Demolition brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L Brick work with old size flyash bricks, straight or curved on plan exc 6m mean radius built in Cement Mortar (1:6) complete all as specified and directed.

M&L for Cement concrete Type D2 1:4:8 type (40 mm graded aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

Providing precast cement concrete block or slab Type C-1 using 20mm graded stone aggregate and set in CM(1:4) in window or door cills, intels, bressumers, steps,quoin blocks (foruse with masonry),string courses,copings .kneelers, apex stones, pier caps,columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets,etc. (of any section indicated), with plain fair faces,including hamfers, weatherings , throating etc. and setting in mortar complete with joints to match complete all as specified and as directed.

M&L for precast louvres and jallies, in cement concrete 1:2:4 type B 0 using 12.50 mm graded crushed stone aggregate set in CM 1:6, 35 mm thick (measured solid), including all mould- ings but excluding frame including dismantling old cement concrete jalli complete all as specified and directed.

M&L rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for ( reinforcement cut as required to facilitate demolition) complete all as specified and directed.

M&L for cement concrete slab in cement concrete Nominal mix 1:2:4 type B-1 (using 20mm graded stone aggregate) in manhole covers, drain covers, shelves etc with plain faces etc complete all as specified and directed.

M&L for mild steel deformed TMT bars of 6 to 8 mm dia cut length bent to shape required incl cranking bending spirally for hooping for column, hooking ends and binding with and incl MS wire (annealed) not less thatn 0.9mm dia or securing with clips complete all as specified and directed.

Preparing new plastered surfaces and applying two coats of cement base paint over one coat of primer complete all as specified and directed.

Supply and fixing 0.63mm mild steel , plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched: including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

Taking down steel gates hydraulically using cranes and refix the same. Area of steel gate is exc 10 Sqm but n. exc 15 Sqm each to carryout necessary repair, straightening and changing any damaged part complete all as specified and directed. Note : (i) Any part of steel gate if required to be changed shall be measured and paid separately under relevant item.

Taking down steel gates hydraulically using cranes and refix the same. Area of steel gate is exc 15 Sqm but n. exc 25 Sqm each to carryout necessary repair, straightening and changing any damaged part complete all as specified and directed. Note : (i) Any part of steel gate if required to be changed shall be measured and paid separately under relevant item.

Balaji Construction Co. (BID ID -3199835)

M/S RAJESH KUMAR & SONS (BID ID -3204922)

M/S SM BUILDER CO (BID ID -3200129)

malik constructions (BID ID -3204906)

DHARMA CONSTRUCTION (BID ID -3205250)

m/s krishna engineers1 (BID ID -3204993)