PETTY ESSENTIAL REPAIRS TO WATER SUPPLY AT MAP ANC AND MAP 4 AREA UNDER GE AF TECH AREA AGRA

Amount

Taking up/down GI/HDPE tubing of any length including fitting from trenches, walls, ceilings for relaying/replacement for the following sizes all as specified and directed :-

(a) 15 mm bore tubing

(b) 20 mm bore tubing

(c) 25 mm bore tubing

(d) 40 mm bore tubing

(e) 50 mm bore tubing

(f) 80mm bore tubing

(g) 100mm bore tubing

Laying only in trenches GI/HDPE tubing in any length with connections as retrieved from item No 1 here-in-before after cleaning, washing or removing old screw thread as required & providing new fittings, as required, complete all as specified and directed for the following sizes :-

(a) 15 mm bore tubing

(b) 20 mm bore tubing

(c) 25 mm bore tubing

(d) 40 mm bore tubing

(e) 50 mm bore tubing

(f) 80mm bore tubing

(g) 100mm bore tubing

Laying only, GI/HDPE tubing with connections in any length as retrieved from item No 1 here-in-before, fixed to wall, ceiling or laid in floor after cleaning, washing or removing old screw thread as required & providing new fittings, wherever required, complete all as specified and directed for the following sizes :-

(a) 15 mm bore tubing

(b) 20 mm bore tubing

(c) 25 mm bore tubing

(d) 40 mm bore tubing

(e) 50 mm bore tubing

(f) 80mm bore tubing

(g) 100mm bore tubing

Supply, laying & testing GI tubing medium grade in trenches in any length including required GI fitting complete all as specified and directed for the following bore :-

(a) 15 mm bore tubing

(b) 20 mm bore tubing

(c) 25 mm bore tubing

(d) 40 mm bore tubing

(e) 50 mm bore tubing

(f) 80mm bore tubing

(g) 100mm bore tubing

Supply, fixing & testing GI tubing medium grade on walls/ceiling or laid in floor in any length including GI fitting complete all as specified and directed for the following bore :-

(a) 15 mm bore

(b) 20 mm bore

(c) 25 mm bore

M&L in for drilling & tapping cast iron mains in position for branch connection of 20mm bore GI pipe with MS clamps including necessary earth work if required etc complete all as specified and directed.

Supply & fixing in renewal gun metal globe gate valve with iron wheel head, screwed both ends ISI marked for the following sizes all as specified & directed :-

(a) 50mm bore

(b) 40 mm bore

(c) 25 mm bore

(d) 20 mm bore

(e) 15 mm bore

S&F in renewal bib tap 15mm bore standard of PTMT any colour screwed for iron pipe and fixed complete all as specified and directed

M&L in renewal for lead joints including spun yarn & taking out old lead by burning etc for the following bore of CI pipe /fittings complete all as specified and directed Note: (i) The quoted rate shall be deemed the necessary earth work (ii) Old taken out lead to be used in making of lead joint

(a) 300 mm bore

(b) 200 mm bore

(c ) 150 mm bore

(d) 100 mm bore

(e) 80 mm bore

Dismantling, opening head of sluice valve, taking out wedge nut/spindle with nut/wedge for replacement and refixing after replacement of Gun metal wedge nut and stainless steel spindle and refacing/regrinding sheet etc for the following size of sluice valve including nuts, bolts, washer, rubber packing and gland complete all as specified and directed.

(a) 300 mm bore

(b) 150 mm bore

(c) 100 mm bore

(d) 80 mm bore

Supply & fixing in renewal of cast iron body sluice valve ISI marked PN 1.6 and conforming to IS 14846 with stainless steel spindle of following sizes complete all as specified and directed.

(a) 200 mm bore

(b ) 150 mm bore

(c) 100 mm bore

(d) 80 mm bore

M&L in renewal for ‘D’ joints complete with collars, rubber ring, nuts & bolts etc for following bore complete all as specified and directed.

(a) 300 mm bore

(b) 200 mm bore

(c) 150 mm bore

(d) 100 mm bore

(e) 80mm bore

(f) 50 mm bore

Supply & fixing in renewal of non return valve ISI marked including complete fixing accessory of following sizes complete all as specified and directed.

(a) 150 mm bore

(b) 100 mm bore

(c) 80 mm bore

Supply,lowering and testing in renewal 32 mm dia high density polythylene column pipe in bore well ISI marked pressure rating PN-10 and with jointing material and HDPE fitting including taking down old U/S HDPE pipe complete all as specified and directed.

Supply & laying in renewal PVC insulated and PVC sheathed copper conductor cable 2.5 Sqmm, 3 core flat for 1100 volts AC including connecting with submersible motor to starter panel complete all as specified and directed.

Taking out submersible pumping set of 1.5/2.0 HP and lowering after repair with replacement of bushes, sleeves, shaft, PVC impeller and rewinding of motor including testing all as specified and directed.

Supply and fixing in renewal wall mounted cubical type panel board with locking arrangement, comprising of starter, condenser, volt meter, indicator lamp, Amp meter, MCB/cut out of suitable capacity for 1.5/2 HP single phase submersible pumping set including fixing arrangement complete all as specified and directed.

Supply & fixing in renewal Cast iron pipes with flanged ends, centrifugally cast, class B, in any length laid in trenches/over head reservoir with Nut bolt and all fitting arrangments of following dia complete all as specified and directed . Note - (a) The subject work is to be carried out upto 21.00 m hight (b) The quoted rate shall be deemed to be included the cost of all tools and plants (c) The contractor shall provide sefty measure to avoid any incident during progress of work.

(a) 80 mm dia

(b) 100 mm dia

(c) 150 mm dia

Excavation in trenches in soft/loose soil n. exc 1.5 Mtr wide and not exc. 1.5 M deep and getting out including forming bottom surface for laying of pipes complete all as specified and directed.

Returning filling in including spreading, leveling, watering and well ramming in layers not exc 25 cm thick complete all as specified and directed.

Removal of excavated material to a distance not exc 50 Meter and depositing where directed at a level not exc 1.5 M above the starting point complete all as specified and directed.

M&L for Cutting of cast iron pipe in position for insertion of new tee, collar etc including necessary earth work if required complete all as specified and directed for the following bore: -

M & L in renewal for flange joints with rubber sheet 3mm thick, including nuts, bolts including necessary earth work if required etc complete all as specified and directed for the following bore:-

Taking out U/S submersible pump set including motor from bore well of capacity 1.5HP after disconnecting all electrical connections & supply, fixing, lowering, commissioning & testing submersible pump set of discharge capacity 70 LPM at 57 metre head single phase , 230 volt AC electric driven 2900 RPM of 1.5 HP including necessary wiring from motor to panel etc complete all specified and directed.

S&F in repairs cast iron foot valve, flanged type with flanged, ISI marked, including making flanged joints with & including 3mm thick rubber sheet, nuts & bolts etc of suitable size for following bore complete all as specified and directed.

(a) 80mm bore

(b) 100mm bore

M & L for construction of brick masonry valve pit with sub-class 'B' brick built in cement mortar (1:6), of size (90 x 90 x 90) cm (internal dimension) with one brick thick walling and150 cm x150 cm x 10 cm base foundation with PCC (1:3:6), type C2 using 40 mm grade stone aggregate , cement plastering 10 mm thick with cement mortar (1:4) on internal & exposed surfaces, of brick work with and including MS cover of size 01mtr x 01mtr made out from 3 mm thick MS sheet with and including (40 x 40 x 5) mm angle iron framing fixed on top of valve pit & painting the steel surfaces with two coats of synthetic enamel paint (first quality) over a coat of red oxide primer, including necessary excavation and earth work and . demolition of the existing old valve pit and removal of old demolished materials and surplus excavated soil to a distance n-exc 50m etc complete all as specified and as directed.

M&L for cutting of existing HDPE/ GI pipe of 40/50mm bore for cleaning/ leakage repairing and re-jointing the same in existing position with & including jointing rings and heating process including all necessary excavation & earth work if required and making good the surfaces as per existing complete all as specified and directed.

M&L for cutting of existing HDPE/ GI pipe of 25mm bore for cleaning/ leakage repairing and re-jointing the same in existing position after cleaning /leakage repair with & including jointing rings and heating process including all necessary excavation & earth work if required and making good the surfaces as per existing complete all as specified and directed.

M&L for cutting of existing polyethylene aluminium polyethylene (PE-AL-PE) pressure/ GI pipe of 15/20 mm dia for cleaning/ leakage repairing and re-jointing the same in existing position after cleaning /leakage repair with & including jointing rings and heating process including all necessary excavation & earth work if required and making good the surfaces as per existing complete all as specified and directed.

S&F in repairs HDPE fittings i.e reducer/ tee/ ring suitable for HDPE/ polyethylene aluminium polyethylene (PE-AL-PE) pressure pipe for stoppage of leakage at different locations/ areas including all necessary excavation & earth work if required and making good the surfaces as per existing complete all as specified and directed for the following sizes:-

(a) HDPE Tee 50x 50 X 16-20 mm bore

(b) HDPE tee of 16-20x16-20x12-16mm dia

(c ) HDPE tee of 20-25x20-25x16-20mm dia

(d) Jointing/ copper rings of 20/25mm dia

Carryout day to day rectification of water supply complaint such as repair, reconnection and replacement of water supply system in air force station Agra area all as directed by Engr in Charge. Note:- Note: (a) 01 x Pipe fitter and 02 x helper will be detailed by the contractor for attending above complaints on daily basis. Cost of which shall be deemed to be included in quoted rates. (b) Replacement of major items shall be measured and paid under relevant items of this schedule. (c) Pipe fitter and helper so detailed by the contractor will report to MES complaint cell at 0845 hrs morning to receive complaint slip from department and complaints shall be rectified within 08 Hours. If contractor fails to detail above tradesmen a panel recovery@ Rs. 500.00 per day shall be made to contractor and shall be recovered from RAR/Final bill. (d) Repairing upto 06 Complaints at different water supply system with minor fittings/ fixtures materials costing upto Rs 500/- will be considered as one job.

Manu Enterprises

MUKTA AND COMPANY

RAJEEV CONSTRUCTION

FUTURE Inc.

M/S BHULLAR CONSTRUCTION COMPANY

M/s S.M. Construction