SPECIAL REPAIRS OF TEMP SHELTER OWT-464 TO OWT-468 AT RE-OPERATIONALISED, PROVN OF OVERHEAD COVERED PATHWAY FROM ACUTE WARD (OWT-134) AND SURGICAL WARD (OWT-162) TO PATIENTS DINING HALL OF MH AND PROVN OF SANITARY LAVATORY FOR OFFICERS FOR MED OPD OF

Amount

B/R SERVICES/WORKS

Demolition Cement Concrete (Un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and Removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed

Taking down/out Unserviceable Rusted/ Worn out Wire Cloth/Netting of any description, fixed with Beads, etc., complete all as specified and as directed.

Hacking out Old Broken Glass (any thickness, size, quality or description) from Wooden or Metal Frame or Stone, Concrete or Brick surrounds including hacking out old Putty or removing Beads, etc., punching or drilling out old Glazing Pins/ Spring Clips, complete all as specified and as directed.

Dismantling Plain or Corrugated Steel Sheeting of any gauge and thickness, complete all as specified and as directed.

Surface Excavation not exc. 30 Cm Deep and ave. 15 Cm Deep and getting out in Soft/ Loose soil, complete all as specified and as directed.

Excavation in Trenches not exc. 1.50 Metre wide and not exc. 1.50 Metre in depth for Foundation etc. or for Shafts, Wells, Cess Pits, Manholes, Pier Holes, etc. not exc. 10 Sqm on Plan and not exc. 1.50 Metre in depth and getting out as in Soft/ Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering and Well Ramming in layers not exc. 25 Cm, in Soft/Loose Soil, complete all as specified and as directed.

Removing Excavated Materials (Soils) not exc. 50.00 Metre and depositing where directed at a level not exc 1.50 Metre above the Starting Point, complete all as specified and as directed.

Excavating in Post Holes (or Similar Holes) in Soft/Loose Soil, Each not exc. 0.50 CUM, getting out and Removing Surplus Soil to a distance not exc. 50.00 Metre and Making Good Surfaces, complete all as specified and as directed.

M&L Sand (as approved) Filling under Floors, Foundations, etc. including Spreading and Levelling, etc., complete all as specified and as directed.

M&L Hardcore Broken Stone or Boulders, Gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 15 Cm thick, watered and well rammed to a True surface, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) in Coping, Bed Plates, Benching, Bed Block, Kerb Stones, etc. including necessary Formwork and Weathering, slightly Rounded or Chamfered Angles and Throating including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork will deemed to be included in the Quoted Unit Rate.

M&L Cement Concrete 1:4:8 (40mm graded aggregate) in Foundations, Filling and Mass Concrete, etc. including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork will deemed to be included in the Quoted Unit Rate.

M&L Cement Concrete 1:3:6 (20mm graded stone aggregate) for Columns, Pillars, Posts and Struts including all necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork will deemed to be included in the Quoted Unit Rate.

M&L Reinforced Cement Concrete (20mm graded stone aggregate) in Foundation including Raft, Footing, Foundation Beam for Column Basement Slab, under reamed Piles, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete (20mm graded stone aggregate) in Beams, Cantilevers, Bressummers, Lintels Over 1.50 Metre Span and the like, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Formwork to Sides of Concrete Foundations, Footings, Bases of Columns, Raft and Raft Beams, Sides and Soffits (if any) of Foundation and Plinth Beams; and Similar Work; Vertical or to Batter, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides and Soffits of Floor or Roof Beams, Girders, Beam Haunchings, Bress-summers, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc. also splays between Floors and Beams, etc., Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Pre-cast Cement Concrete Block Masonry with Solid Blocks of Size 300x200x200mm or 300x200x100mm, having Compressive Strength of not less than 100 Kg/ Sq Cm (as per IS-2185) in Cement Concrete 1:3:6 (20mm graded stone aggregate), exc. 10 Cm in Width and Setting in Cement Mortar 1:6, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 40mm thick in Damp Proof Courses to Horizontal or Vertical Surfaces including Use & Waste of Formwork and Applying evenly a coat of Blown type Bitumen @ 1.50 KG/SQM and blinding with Clean Dry Sand @ 0.05 CUM/SQM, complete all as specified and as directed.

S&F Solid PVC Door Frame of Size 50x47mm made out of 5.0mm thick Plain Colour PVC Sheet Reinforced with Mild Steel Square Tube and fixing in Opening as per Specification and Drawing of MES Schedule, complete all as specified and as directed.

S&F Factory Made Solid PVC Moulded Door Shutter, 28mm to 30mm thick (Stiles), with 2, 4, or 6 Raised Panel design with 2.0mm thick Moulded PVC Sheet on the Front Face and 2.0mm Plain Colour PVC Sheet on Back Face, with Particle Board Core and fixing in Frame at Site as per Specifications & Drawing of MES Schedule, complete all as specified and as directed.

S&F Steel Ventilator with Top Hung Shutter Hinges with Steel Peg Stay, complete with Glazing Bars, dovetailed or welded, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt of Size 150mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy, anodised, Sliding Door Bolt 250mm long (as approved) with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and Fixed, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of Size 75mm, complete all as specified and as directed.

S&F Aluminium Handle of Size 125mm, anodised, Cast type, complete all as specified and as directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed.

S&F Sheet Glass 3.0mm thick, Plain, Ordinary quality and Glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

M&L TMT Bars 10mm dia and Over, Cut to length, Bent to Shape required including Cranking, Bending Spirally for Hooping for Columns, hooking Ends and Binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8.0mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Mild Steel Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes including Bolts, Hooks (Stay) for large Gates; Hook and Pintle Hinges: large Hasps and Staples; Hand Made Sliding Bolts; Clamps; Holdfasts; Wall Ties and Similar Small Articles conforming to Fe-290 Gde-E-165, complete all as specified and as as directed.

M&L Framed Brackets of Angles or Tees with Web and Flanges, cut to Shape, drilled and countersunk for Screw including bending and welding Angles as necessary, Gusset Plates, Riveting, etc., not exc. 10 KG Each Brackets, conforming to Fe-290, Gde E-165, complete all as specified and as directed.

M&L Rolled Mild Steel Sections in Compound Girders and Stanchions, Lattice Girders, Aerial Masts, Staging for Water Tanks and the like including Caps, Bases, Splices, etc. built up from Two or More Beam or Channel Sections or Angles with Plates including all Lattice Bars, Stiffeners, Gusset Plates, etc., conform to Fe-410-W (Gde E-250) Quality 'A', complete all as specified and as directed.

M&L Mild Steel Tublar Trusses, Rafter, Purlins, etc. including Special Shaped Washers, etc. complete using ERW or Induction Butt welded Tubes, confirming to IS:1161-1979, Grade St-240, complete all as specified and as directed.

M&L Plates (Plain or Chequered) Channels, Square cut or Notched (Ordinary and Counter Sunk) forming Holes, without any Aattachment, conform to Gde Fe-410-W (Gde E-250) Quality 'B', complete all as specified and as directed.

M&L Mild Steel Screw Bolts (Machine made) of any description (Lengths and Diameter of Bolts as required at Site of Work/ as directed) with Hexagonal or Square Heads at One End and screwed the Other End, or screwed Both Ends, Each screwed End to be fitted with Washers and One Hexagonal or Square Nut, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Plain Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Ridges/ Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 75mm thick in Sub-base to Flooring, etc., complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 100mm thick in Sub-base to Flooring, etc., complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 100mm thick in Flooring, etc., laid in Alternate Panels, finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 50mm thick in Flooring, etc., laid in Alternate Panels, finished Concrete Surfaces Even and Smooth with using Extra Cement, complete all as specified and as directed.

M&L Glass Dividing Strips 38mm Wide and 3.0mm thick and inserted in Position, conform to Design, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 25mm thick in Sub-base for laying of Tiles, etc., Maintaining Level Uniformly, finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Non-skid Ceramic Coloured Tiles (1st quality and as approved) 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Glazed Ceramic Coloured Tiles 300x450x6.0-7.0mm thick (1st quality and/or as approved) in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Machine Pressed Pre-cast Concrete Interlocking Paver Block 60mm thick of M-35 Grade, with Grey Cement and Pigment of any shape and size (as ordered), conforming IS-15658-2006, ISI Marked, laid dry over Clean dry Sand and grouted with Clean dry Sand in Floors, complete all as specified and as directed. NOTE : Clean dry Sand will be Measured and Paid separately under appropriate Item.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) 75mm thick in Plinth Protection, etc., Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without using Extra Cement, complete all as specified and as directed.

M&L Bitu Mastic Filling comprising 1 Part of Bitumen of Grade 85/25 and 3 Parts of Sand by Weight, complete all as specified and as directed.

M&L Rendering 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering 15mm thick on Bricks/Pre-cast Blocks or Concrete Works consisting in 2 layers, Backing/Under layer of 10mm thick in Cement Mortar 1:4 and Float/Top layer 5.0mm thick in Cement Mortar 1:4 including mixing WPC to Float/Top layer, finished Fair and Even, complete all as specified and as directed NOTE : Water Proofing Compound (WPC) will be Measured and Paid separately under appropriate Item.

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion (of approved Tint) over a Coat of Chalk Whitening (Priming Coat), complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint (of approved Tint) over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, over 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing Old Rusted Steel and Iron Surfaces of CGI Sheets on Roofing, Walls, etc., over 10 Cm in Width or Girth and applying a Coat of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) in Camouflage Pattern, complete all as specified and as directed.

S&F Galvanised Steel Tubing 15mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F Galvanised Steel Tubing 20mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia) Cast Copper alloy, Fancy type, Chromium Plated, with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule and Fixed, complete all as specified and as directed.

S&F Pillar Tap 15mm bore (dia), Cast Copper alloy with Capstan Heads, Chromium Plated, Fancy type, Quarter Turn (Form Flow), screwed down, high pressure, with or without lettered 'Hot' or 'Cold' with long screwed Shanks and Fly-nuts, screwed for Iron Pipe and Fixed, complete all as specified and as directed.

S&F Angle Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions and Fixed, complete all as specified and as directed.

S&F Stop Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions and Fixed, complete all as specified and as directed.

S&F Gun Metal Globe/Gate Valve 20mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe and Fixed, complete all as specified and as directed.

M&L Rotational Moulded Polyethene Water Storage Tank 500 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS:12701-1996, hoisted and fixed in Position all as specified in MES Schedule and Providing Water Connections, complete all as specified and as directed.

S&F PTMT Ball Valve 20mm bore (dia), having weight not less than 210 Gram, high pressure with Epoxy Coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe and Fixed, complete all as specified and as directed.

M&L Vitreous China White Wash Down Water Closet Pan (Pedestal Pattern) with Trap and Fixing Bolts and Making Good to Floor/Distrubed Surfaces in Cement Mortar 1:3 and Fixed, complete all as specified and as directed.

S&F Plastic Water Closet Seat and Cover for Water Closet Pan (Pedestal Pattern), White, Closed Pattern with Flat bottom and Cover and Mild Steel Chromium plated or Aluminium anodised Hinging Device and Fixed, complete all as specified and as directed.

S&F Health Faucet (as appproved), Brass Chromium Plated with Flexible Tube 1.00 Metre long and Wall Hook and Fixed, complete all as specified and as directed.

S&F PVC Flushing Cistern 10 Litre capacity White, Low Level, Valveless, Syphonic Action type with Inlet, Ball Valve, Float & Handle, and PVC Flush Pipe 32mm bore (dia) for suitable Length, a Pair of Cast Iron Brackets Erecting Stand duly painted including cutting and pinning in Ends, Making Good disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F Vitreous China White Wash Hand Basin 450x300mm in Size, Flat Back with Pedestal including Brass Chromium Plated Waste Fitting 32mm bore (dia) and PVC Waste Pipe 32mm bore (dia) including a Pair of Cast Iron Brackets Brackets Erecting Stand duly Painted, Cutting and Pinning in Ends and Fixed including Making Good disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F Bottle Trap 32mm bore (dia), Brass Chromium plated suitable for Wash Hand Basins with Inlet and Outlet, screwed for Pipe or Connections including necessary Packing, Union, Cap and Fixed, complete all as specified and as directed.

S&F Toitet Paper Holder of size 150mm (as approved), Brass Chromoum Plated with Rod to hold Paper Roll and Fixed, complete all as specified and as directed.

S&F PVC Connection Pipe 15mm in Size and 450mm in length with PTMT Nuts suitable for connecting with Flushing Cistern, Wash Hand Basin, etc., complete all as specified and as directed.

S&F Vitreous China White Soap Dish (as approved), not less than 125mm in Size, fixing to Walls with and including Chromium plated Brass Screws and Wooden/ Plastic Cleats and Fixed, complete all as specified and as directed.

S&F PVC (SWR) Floor Trap having Diameter of Outlet 75mm, Plain with Grating including Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) Pipe 110mm bore (dia), Single Socketed, in any length with Rubber Ring Joints, fixing to Walls or laid on Floors, etc., complete all as specified and as directed.

S&F PVC (SWR) Bend 110mm bore (dia), any Radius, etc. and Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) Vent Cowl 110mm bore (dia) and Jointing with Solvent Cement, complete all as specified and as directed.

E/M SERVICES/WORKS

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded single core FRLSH Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including Concealed PVC Rigid Conduit (ISI Marked) of suitable Size and Conduit Accessories viz Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable (Green Colour) as Earth Continuity Wire for ONE 3/5 PIN SOCKET 6 AMP POINT on SAME BOARD, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core FRLSH Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including Concealed PVC Rigid Conduit (ISI Marked) of suitable size and Conduit Accessories viz Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6/16 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, Flush type, 1-way, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Socket Outlet 6 Amp, 5 Pin, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6/16 Amp, 3 Pin, 2-in-1, Multi-plug, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Ceiling Rose 65x50mm, 3 Terminals, Surface Bakelite suitable for 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Decorative LED Light Fitting 1x10 Watt Bulkhead Luminaires including LED Light, Driver, Holder, Connecting up with and including of suitable Size and Length Flexible Copper Conductor Cable, 3 Core, complete all as specified and as directed.

S&F LED Light Fitting 10 Watt, Mirror type with High Out put Diffuser 2 Feet, 220 Volt AC, Decorative type with Driver Holder and LED Lamp and Connecting up with and including of suitable Size and Length Flexible Copper Conductor Cable, 3 Core, complete all as specified and as directed.

S&F LED Tube Light Fitting 1x20 Watt with 20 Watt LED Tube, Wall or Ceiling mounted type with all Accessories, Pre-wired, fixing on and including providing PVC Box (2 No), Connecting up with and including of suitable Size and Length Flexible Copper Conductor Cable, 3 Core, complete all as specified and as directed.

S&F Exhaust Fan 250mm Sweep made of Sturdy Engineering Plastic complete with Louvers Shutter, 230 Volt, 50 Hz, RPM 1200, Copper Winding with Fixing Arrangement using Fastener, Connecting up with and including of suitable Size and Length Flexible Copper Conductor Cable, 3 Core, complete all as specified and as directed.

S&F MCB Single Pole 6 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and Connecting up, complete all as specified and as directed.

S&F MCB Single Pole & Neutral 10 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and Connecting up, complete all as specified and as directed.

S&F Sheet Metal Enclosure for DB's when MCBs to be used SPN 4-way, 240 Volt AC, Double Doors, Epoxy Based Powder coated suitable for mounting MCB DP/ SPN as Incomer and MCB SP as Out-goings with 200 Amps rated Bus-bar, Neutral Bar, Earth Bar, Connecting Cable Links and Connecting up, complete all as specified and as directed.

Supply and Laying or Fixing or Passing through Pipe, 1100 Volt grade Heavy duty Cable with PVC insulated Aluminium Stranded Conductor served with an Inner sheathing of PVC Tape armoured with Galvanised Steel Wire or Tape and Overall PVC sheathed 10 Sqmm Nominal Cross Section, 2 Core in Service Connection, complete all as specified and as directed.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of Size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing, complete all as specified and as directed.

M/S CHANDAN ENTERPRISE

D. D. Construction

FREEZCON

STANDARD ELECTRIC WINDERS

M/s GANDHESWAR PHUKAN

AFTAB ENTERPRISES

R.D.CONSTRUCTION