MOEI , Fans, Compound light and other accessories installed at ITI, Savitri Bai Phulle, Mori Gate, during 2026-27. (SH Replacement of burnt AMF Panels and LT Panel at SBP, ITI, Mori Gate, Govt of NCT of Delhi.)

Supplying, installation, testing & commissioning of cubical type LT panel suitable for indoor/outdoor application with IP42/IP54 (with canopy) protection according to the site requirements, 415 V, 3 Phase, 4 Wire 50 Hz AC supply system fabricated in compartmentalized design having bus bar chamber duly fabricated from CRCA sheet steel of 2 mm thick for frame, back, sides, partition & doors and 3mm thick for glad plate duly powder coated in approved shade including cleaning & finishing complete with 7 tank process complete with non extensible type four strip aluminium alloy bus bars of required capacity as per incomer rating, hight conductivity, DMC/ SMC bus bar supports having short circuit withstand capacity of 31 MVA for '1' Sec., bottom base channel of MS section not less than 100 mm x 50 mm x 5 mm thick, entire panel shall have a common earth bar of size 25 mm x 5 mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of Al. bus bars, control wiring including all necessary items as per direction of Engineer-in-Charge. LT Panel Incomer 1. 250,FP 25KA MCCB WITH SPREADER LINK AND ROTORY HANDLE – 1 No. 2. DIGITAL VAF METER – 1 No. 3. R, Y, B PHASE INDICATION LAMP – 3 Nos. 4. C T 250/5 5 VA 1.0 CL – 3 Nos. 5. 06A SP MCB – 3 Nos. Busbar 1. 300A TPN ALUMINUM BUSBAR ALUMINIUM – 1 Set Outgoing 1. 100,FP 25KA MCCB WITH SPREADER LINK AND ROTORY HANDLE – 4 Nos.

AMF PANEL FOR 62.5 KVA DG SET supplying & commissioning of indoor type automatic mains failure control including auto by-pass panel having CRCA sheet steel of 2 mm thick for frame, back, sides, partition & doors and 3mm thick for glad plate duly powder coated in approved shade including cleaning & finishing complete with 7 tank process complete with non extensible type four strip aluminium alloy bus bars of required capacity as per incomer rating, hight conductivity, for 250 kva silent type dg set complete with relays, timers, set of cts for metering & protection and energy analyzer to indicate currents, phase and line voltages, frequency, power factor, kwh, kvarh& provision for overload, short circuit, restricted earth fault, under frequency, including the following: a) 125A TP mccb 25ka – 2 Nos. (for incomer) b) 125A Changeover switch – 2 Nos. (for bypass arrangement) c) 125A TP Contactor – 2 Nos. (for outgoing) . Metering a) VAF meter - 1 no. b) RYB indication lamp - 3 nos. c) 6 a sp MCB- 3 nos. d) 150/5 a ct class-1 - 3 nos. e) Over and under voltage relay- 2 nos. f) Reverse power relay -1 nos. g) window annunciator - 1 no. AMF System A) DC Ammeter 0-30a - 1 No. B) DC Volt Meter 0-50a - 1 No. D) 32A DP MCB- 1 No. E) Push Button With Element - 3 Nos. F) Auxiliary Relay 230v Ac With 2 No. + 2 Nc- 2 Nos. G) 4/C Relay 24v Dc -3 Nos. I) Battery Charger- 1 No. J) On Delay Timer - 2 Nos. K) Normal Terminals 2.5 Mm - 10 Nos. L) Auto Manual Sel Switch - 1 No. M) On/ Off Light - 2 Nos. Bus Bar 150A TPN Aluminum Bus Bar AMF Panel For 62.5 kva Dg Set

Supply, installation, testing and commissioning of 3D (three dimensional) backlit IP 65, letter forms display of approved signage of approved artwork and aspect ratio and minimum 12 swg protruded letter forms cutting to be made by CNC router as per approved size of letters in 04 languages. translucent ISI marked acrylic sheet used for letters fabrication to be of minimum 12 SWG thickness and base sheet to be of minimum 03mm thick ACP sheet suitable to glow with horizontal line array of LED modules fixed at equidistant on suitable spacing firmly on mm thick sunboard sheet. ACP sheet is to be used for boxing up and properly supported by MS pipe structure of size not less than 50x25 mm of minimum 17 SWG thickness. The board should be supported with the MS pipe horizontal member from inside centrally. LED modules must be in conformity to prevailing BIS codes and buld technology SMD LED, lumens output per watt should not be less than 100 Im per watt,CRI>80, life 50000 hrs. color temperature 6500k, light effect cool daylight, startup time<0.5s, IP 65, voltage withstand 190 V-305 V, 50/60 Hz, independent driver with 2.5 Kv surge protection and drver/ power supply unit to be housed in cubicle made outside on signage board on back side with opening or easy maintenance and replacement of power supply daily programmable electronic timer switch minimum 2 KW etcasn reqd. frame 4 feet width 60mm deep 25 mm x 25 mm having thickness not less than 24 SWG SS 304 grade angle iron cladding all around the board as per drawing approved by engineer-in-charge.

Supplying, laying and fixing of following sizes XLPE insulated PVC sheathed aluminum conductor armoured cable of 1.1 KV grade on surface etc complete as required. a) 3 X 10 Sq.mm

b) 4 X 16 Sq.mm

c) 4 X 25 Sq.mm

d) 3.5 X 35 Sq.mm

e) 3.5 X 50 Sq.mm

Dismantling of existing substation equipment and Credit bye back to contractor of old Dismantled material, 5.01) MAIN LT PANEL

5.02) AMF Pannel