REPAIRS TO JOINERY ROOFING FALSE CEILING AND CONNECTED ITEMS TO CERTAIN OTM AND MD ACCN AT SI LINES UNDER GE BHOPAL

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.

Taking down chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

Taking down shutters of any description not exceeding 1 Sqm each complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Taking down shutters of any description exceeding 2 Sqm each complete all as specified and directed

Taking down shutters of any description and refixing in the same opening exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Taking down shutters of any description and refixing in the same opening area n exceeding 1 Sqm each complete all as specified and directed.

Taking down shutters of any description and refixing in the same opening exceeding 2 Sqm each complete all as specified and directed.

Demolition of Brick or stone massonry work built in cement or cement lime mortar complete all as specified and directed.

M&L for Brick work with fly ash bricks (Modular), straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with fly ash bricks (Modular), straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) complete all as specified and directed.

M&L for Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in roof kerbs, cills, seismic and other similar bands, plinth courses, copings, bed plates, bond stones, etc including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing tiles/ rubbish off the permises to a distance not exceeding 250m complete all as specified and directed.

M&L for 25 mm thick Cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in sub base of floors, etc complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in vertical surfaces such as skirting, dados etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 10mm thick rendering in CM 1:3 complete all as specified and directed.

M&L for Glazed ceramic coloured tiles 350mm x 250mm x 7mm thick or 450mm x 300mm x 7mm thick, in vertical surfaces such as skirting, dados and risers to steps, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 10mm thick rendering in CM 1:3 complete all as specified and directed.

M&L for Marble work 18-20 mm thick (Makrana white) (table rubbed and polished/ moulding) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing n white cement (1:2) using marble dust with admixture of pigment to mactch with shade including grinding, moulding and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking/wash basin platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including grinding, moulding and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

S&F laminated wooden flooring "Action Tesa" or equivalent as approved by GE including polishing all as per manufacturers direction, including taking old flooring complete all as specified and directed.

Supplying & fixing powder coated (minimum thickness 50 micron) aluminium sections of required size for door windows frames shutters and partitions including aluminium hinges of required size jointing cleats, screws sash fasteners, plug for fixing with walls, columns, etc complete all as specified and directed. [MAKE: JINDAL/ AJIT INDIA/ HINDALCO as approved by GE]

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames, glazed with putty or fixed with beads complete all as specified and directed.

S&F Sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5Sqm in each pane complete all as specified and directed.

S&F Sheet glass 4mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5Sqm in each pane complete all as specified and directed.

S&F Sheet glass 4mm thick, ordinary quality and glazing to aluminium door, window & partition including pad/gasket, area exceeding 0.5Sqm in each pane complete all as specified and directed.

S&F Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed.

M&L for Second class hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed.

M&L for 2nd class hardwood plain fillets, square, rectangular or triangular in section, wrought, fixed with nails, cross sectional area exceeding 13 sqcm but not exceeding 25 sqcm, complete all as specified and directed.

M&L for factory made Second class hardwood 35mm thick plain, framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged) or of 12mm thick veneered particle board medium density, wood particle board with commercial face veneers complete all as specified and directed.

M&L for factory made Second class hardwood glazed and skeleton door shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete all as specified and directed.

S&F factory made Flush shutters 40mm thick, solid core construction, with block board core and ply wood face panels, commercial type on both sides complete all as specified and directed.

S&F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed.

S&F 100mm size butt hinges extruded aluminium alloy with galvanised mild steel anodised and fixed type B-21 complete all as pecifeid and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, 100mm size complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, 125mm size complete all as specified and directed.

S&F Aluminium handles, cast type anodised, 150 mm size complete all as specified and directed.

S&F Aluminium anodised barrel tower bolts of extruded section, 150 mm long complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt 250 mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F 300 mm, ordinary rat tail rod pattern springs of mild steel including roller and roller plate complete all as specified and directed.

M&L in repair 25mm Stainless steel Drepary curtain rod decorative type incl fancy type bracket & nobs complete all as specified and directed

Dismantling wall and ceiling boards or insulation boards, any thickness, any description, including cover fillets complete all as specified and directed.

S&F GI frame work size of grid 605 mm x 605 mm for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylong sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kuled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, complete all as specified and directed.

Providing and fixing 10 to12mm Gypsum board ceiling fixed with GI angle/channel frame work incl GI wire/ mesh, etc in different levels all complete including joints filled with paster of paris, putty including POP work/Cornices and applying two coat of oil bound distemper, complete all as specified and direcetd.

M&L for galvanised cold rolled steel section framework of size 600 x 600mm grid size using 24x38x0.50 (composite thickness) tee (bottom pre coated) & 24x24x0.50mm (composite thickness) wall angle including suspenders as per manufacturer’s instructions complete all as specified and directed. [Make: GABSON(Gabsec) or equivalent as approved by GE]

S&F asbestos free calcium silicate board of size 600x600x6mm, fixed to steel frame work in ceiling with & including applying two coats of oil bound distemper complete all as specified and directed. NOTE:- Cost of making frame work for light fittings, etc is deemed to be included in the quoted unit rate

S&F 40mm wide of flap continuous (piano) hinges, brass, bright finish complete all as specified and directed.

S&F in repair prelaminated partcle board 18/19 mm thick, exterior grade, prelaminated both side with decorative choice lamination fixed with nails to aluminium framed work complete all as specified and directed.

S&F 100 mm brass handle, cast type, polished bright complete all as specified and directed.

M&L 2nd class hardwood nexc 3 Sqcm wrought filets but bull nosed, splayed, chamfered or rounded on one edge or face complete all as specified and directed.

Taking down cement plaster on brick or stone walls/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick in two coats of 10mm thick on faces of brick work or concrete surfaces; first coat (rendering coat) in cement mortar 1: 4 and second coat 5 mm thick (finishing coat) in cement mortar 1: 4 mixed with water proofing compound (water proofing compound to be measured separately as supply only) and finished fair and even complete all as specified and directed.

Dismantling Asbestos cement (Corrugated, semi corrugated, etc) sheets including ridges in roof covering complete all as specified and directed.

Dismantling timber in fillets rails, posts, rafters, purlins, etc under 40 Sqcm in section unframed work complete all as specified and directed.

M&L preparation of New or previouly untreated surface of steel and iron surface of any description and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet, 0.5mm thickness, of colour as approved by GE, having tensile strength of 550 Mpa as in roof coverings/cladding to wall, etc, fixed with & including self tapping screws on angle frame complete all as specified and directed. [MAKE: TATA BLUE SCOPE / EVEREST INDUSTRIES/JINDAL/ make as per Appx 'C' list of make]

All as per item No 59.00 above but plain sheeting, in ridges completed all as specified and directed.

M&L for 1.5 mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugations sid lap fixed with L type or J type or cranked hook bolts complete all as specified and directed.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc complete, drilled for fixing of steel sheeting or other covering, doors, etc to be prepared for hanging or sliding with and including either hooks and hings or steel hanging door fittings (including of steel sheeting or other covering.(Fe-410-W(Gde-E250) complete all as specified and directed.

S&F Steel work in tubular/structural trusses, purlins, etc including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 or steel sections conforming to Fe 410-W (Gde E-250) quality -A complete all as specified and directed.

S&F Mild steel conforming to Fe-290 Gde E-165 in bands, straps, supports or stays for rain water, including bolts, if required, hook and pintle hinges; handmade sliding bolts; clamps; hold fasts; hooks for hanging fans and similar small articles complete all as specified and directed.

S&F kitchen baskets with 100 % stainless steel, non - magnatic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism kitchen capable of holding plate, cup, saucers, bowls and dongas with 500 mm car case depth of 558mm and height 100mm complete all as specified & directed. Make Life time -code : DSN 21 or equivalant as approved by GE

S&F kitchen baskets with 100 % stainless steel, non - magnatic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism kitchen capable of holding plate, cup, saucers, bowls and dongas with 500 mm car case depth of 558mm and height 150mm complete all as specified & directed. Make Life time -code : DSN 21 or equivalant as approved by GE

S&F kitchen baskets with 100 % stainless steel, non - magnatic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism kitchen capable of holding plate, cup, saucers, bowls and dongas with 500 mm car case depth of 558mm and height 200mm complete all as specified & directed. Make Life time -code : DSN 21 or equivalant as approved by GE

S&F in repairs 18mm plywood grade BWR, type BB fixed with screws to timber frame work complete all as specified and directed.

S&F in repairs 0.9mm thick decorative laminate type 1, of surface finish, colour and pattern as approved, fixed with approved adhesive as per maker's instructions complete all as specified and directed.

S&F Pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, with & including filing of cement concrete typ B-0, 1:2:4 using 12.5mm graded stone aggregates inside frames complete all as specified and directed.

S&F Pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, with & including filing of cement concrete typ B-0, 1:2:4 using 12.5mm graded stone aggregates inside frames complete all as specified and directed.

S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F in repairs to Aluminium (Extruded section body ) Door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed complete all as specified and directed.

S&F double rebate openable/fixed windows made of galvanized steel colour coated/powder coated (base steel as per IS 513 of “D" quality, galvanized as per IS 277 with zinc of 120 grams/sqm) with total thickness of coating 0.58 microns, primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns thick, outer frame section 72 x 55 mm, centre mullion section 72 x 50 mm, shutter section 47 x 20 mm,fly mesh section 40 x 20 mm and the fixed glass beading section 12 x 12 mm, outer frame and mullions shall consists rebate for glazed shutter, fly mesh and 20 mm provision for guard bars/grills, the sections cut to length mitre joined with corner bracket, centre mullions fixed with mullion cap, stay, handles, latch, 2 Nos of heavy duty stainless steel pivot hinges per shutter and panelled with 5mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade), fitted using EPDM (Ethyl Propylene Diamine Monomer) gaskets including fixing windows in the concrete/masonry wall by means of self-expanding screws, including 10mm Square bars welded to 6x12mm flat at a distance 150mm c/c (pitch) etc. complete all as specified and directed. [MAKE:- NCL Alltek and Seccolor Ltd (Model:ECO 4000) or equivalent as approved by GE]

S&F in repairs Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size:- 914mm x 460mm x 203, bowl size:- 405mm x 354mm x 203mm, including CP waste coupling and 32mm dia PVC waste pipe of suitable length complete all as specified and directed. [MAKE:- Prayag (Cat No.1239D Gloss) or equivalent in NIRALI/BLUE STAR/ make as per Appx 'C' (list of make) as approved by GE]

S&F Magnetic catches for cupboards with plastic body and striking plate not less than 40mm including letting in and fixed complete all as specified and directed.

S&F in repairs 12mm thick toughfen glass in door, partitions etc similar work etc in approved shape and design complete all as specified and directed.

S&F in repairs 40 mm dia, cupboard knobs fixed with nut, screws and washers of mild steel, bright finished complete all as specified and directed.

S&F in repairs stainless steel plate rack of minimum size 31”x36’x10” fixed with screws on wall complete all as specified and directed. [Make : PRAYAG (Model No P-348) or equivalent in NEELKAMAL/NIRALI/ make as per Appx 'C' list of make as approved by GE]

S&F in repairs stainless steel plate rack of minimum size 24”x30’x10” fixed with screws on wall complete all as specified and directed. [Make : PRAYAG (Model No P-330) or equivalent in NEELKAMAL/NIRALI/ make as per Appx 'C' list of make as approved by GE]

S&F in repair to Door Bottom Sealing Strip Guard for Home (Size-36 inch) Complete all as specified and Directed.

S&F in repair to Door Bottom Sealing Strip Guard for Home (Size-48 inch) Complete all as specified and Directed.

S&F in repair CP sliding door lock (Item Code No SLDL-W1-NP) complete all as specified and directed. Make-By Ebco Pvt Ltd or equivalent make as per Appx 'C' list of make as approved by GE]

M&L for Cabinet Hinges Soft Close SS 8 Crank complete all as specified and directed

M&L for 20-25 mm thick polished cuddapah stone slab (single piece) as in cooking platforms and like; with & including 15mm thick screed bed in CM 1:4 and pointing in grey cement and making hole for LPG gas pipe complete all as specified and directed.

S&F in repairs Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor; overall length of cover plate 150mm complete all as specified and directed.

S&F Factory made solid PVC moulded door shutter with particle board core 28 to 30mm thick (style) with 2, 4 or 6 raised panel design with 2mm thick 3D plain colour PVC sheet on the front face and 2 mm plain colour PC sheet on back face complete all as specified and directed.

S&F in repairs MS powder coated peg sets of 3 Nos pegs, heavy quality complete all as specified and directed.

S&F in repairs MS powder coated peg sets of 6 Nos pegs, heavy quality complete all as specified and directed.

Taking down aluminium door shutters of any description & area exc 2 sqm but n exc 4 sqm each and refixing in the same/other opening after carrying out necessary repairs replacing rubber beading and jointing cleats (if required) and refixing builders hardware as required and renewal of unserviceable screws complete all as specified and directed.

Taking down aluminium window shutters of any description & area n exc 2Sqm Each and refixing in the same/other opening after carrying out necessary repairs replacing rubber beading and jointing cleats (if required) and refixing builders hardware as required and renewal of unserviceable screws complete all as specified and directed.

S&F in repair anodized /powder coated aluminium mesh guard/grill of size 50mmmx50mm & wire 5 to 6 mm thick of approved make and pattern cut to the size as required at site and fixing to aluminium window frame fixed with and including aluminium F channel and meeting channel complete all as specified and direced.

S&F in repair to Solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and direced.

S&F in repair 5mm thick PVC sheet fillet of width 35mm for wall pannelling inclusive of fixing on to wall to make PVC Frame complete all as specified and direced.

M&L for UV coated prelaminated MDF Board, Grade I and Type IV (PLMDF–14)), 25 mm thick, high gloss UV coated, optimum curing of UV coating, MSR-A1 Micro-scratch resistance class according to procedure A of DIN EN 16094, including framework of structural timbers of group B, first or second choice as per IS 3629: 1986 and stainless steel screws and including fixing of timber framework on walls and the board on timber framework as per manufacturer’s instructions complete all as specified and as directed.

All as per item No 29.00 here in before but bullnosed, splayed, chamfered or rounded one edge or face, wrought, decorative type fixed complete as in cornices and similar works complete all as specified and as directed.

Schedule of credit (calculation will be done off line) Rs. 123175.00

Vee kay construction

Nakoda Constrcution Company

M/S Shanti Traders

Samaksh Enterprises