SPECIAL REPAIR TO TOILET BLOCKS JCO OR BATHROOMS OF BLDG NO P 619A P619B P619C P619D TOILET NEAR TA292 BLDG NO TO545 AND PROVISION OF CERTAINS REVENUE WORK AND MINOR WORK IN THE AOR OF AGE BRI BRII EMI EMII UNDER GE 865 EWS

Amount

Demolition of cement concrete (unreiforced) in ground floor and pavings n'exc 15cm thick below or above ground level complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including wall cement mortar, bedding (But not backing ) and rubbish of premises complete all as directed.

Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets) any thickness including covered fillets and supporting members, complete all as specified and as directed.

Dismantlng framed wooden fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc under 40 Sq.cm in secton unframed work, complete all as specified and as directed.

Demolition of precast concrete block walling built in cement mortar including all quoins, arches , pillars etc all as specified and as directed.

Taking down cement plaster on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc. complete all as specified and as directed.

Taking down chowkats / frames with shutters (without taking off shutters from the frames) area n'exc 1.5 Sqm each complete all as directed by Engr-in-charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as directed by Engr-in-charge.

Hacking out old broken glass (any thick ness, size, quality or description) from wooden panes or stone, concrete or brick surrounds, glazed with oil putty or fixed with beads complete all as specified and as directed .

Dismantling plain or corrugated steel /fibre sheeting any guage thickness including nanital or similar pattern complete all as specified and as directed

M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with screws/nails to timber frame work as in wall panelling, shelves/boarding complete all as specified and as directed.

M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with nails to timber frame work as in ceiling panelling, shelves/boarding complete all as specified and as directed.

M&L 6mm (5 ply) thick veneered decorative (Knoty Pine) plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed with nails to timber frame work as in wall paneling, complete all as specified and as directed.

M&L 6mm (5 ply) thick veneered decorative (Knoty Pine) plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed with nails to timber frame work as in ceiling paneling, complete all as specified and as directed.

M&L French polishing on wood or wood based surface of any width or girth or any description,including cleaning and preparing the surface including a coat of wood filler over new surface with two or more coats complete all as specified and as directed.

M&L for 2nd class soft wood clean sawn as in battens for grids of ceiling & lining fixed with nails exc 13 sqcm and n exc 25 sqcm in section.complete all as specified and as directed.

M&L for 2nd class soft wood clean sawn as in beeding for edges of Ceiling ,lining ,or wooden flooring work fixed with nails exc 6 sqcm and n exc 13 sqcm in section.complete all as specified and as directed.

Dismantling boarding / wooden flooring of any description ,fixed in any positon, complete all as specified and as directed.

M&L for hard wood 2nd class factory made wooden boarded floors 10mm thick and skirtings planed one side & edges tonged and grooved or rebated , including backing with thermocol sheets ,over 6 micron polythylene sheeting over the concrete to minimize moisture migration from the concrete complete all as specified by manufacture all as specified and directed.

M & L for 75 mm PCC 1:3:6 type C-2 using 20mm graded aggregate as plinth protection finished even and smooth with out using extra cement, complete all as specified and directed.

M&L Forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound Grade 'A', complete all as specified and as directed.

M&L for PCC type D2(1:4:8) using 40mm graded crushed aggregate as mass conc and filling of foundation, complete all as specified and as directed.

M&L for pre cast solid block masonry set in CM 1:6 & casted in cement concrete type C-1 (1:3:6) using 20mm graded curshed stone aggregate complete all as specified and directed.

M&L for 10mm thick rendering on fair faces of Stone wall works finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified and as directed.

M&L for 15mm thick rendering on other than fair faces of brick works in two layers 10 mm & 5 mm thick using water proofing compound for outer layer of 5mm thick finished even and fair without using extra cement in cement mortar 1:4 complete all as specified and as directed.

Supply only integral liquid water proofing compound complete all as specified and directed. Make : Pidilite/Sika

M & L for two coat of cement base paint on newly plastered surfaces of wall, including preparation of surfaces, complete all as specified and as directed.

M&L for preperation of new plastered wall surface of wall any description and applying three coat of white wash complete all as specified and as directed.

S&F anodised aluminium frames for door, windows, ventilators with one or more rebates including joining cleat for fixinf etc complete all as specified.

S&F Anodised aluminium door shutters, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading screws etc. complete all as specified.

S&F Anodised aluminium window and ventilator shutters,including aluminium jali fixed in one side, side hung type without sash,aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150mm long (1 Nos) hinges type B-21 100mm long (2 Nos) suitable handle (1 Nos) etc. complete all as specified.

S&F for 40 mm thick Flush shutters Ladkh pattern , solid core construction ,with block board core and plywood face panels commercial type on both sides , Supply and fixed to chowkats , complete all as directed by Engr-in-charge.

M & L for preparing new wood & wood based surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L sheet glass 3mm thick ordinalry quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane complete all as specified and as directed.

S&F in repairs Galvanised mild steel wire cloth ,0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples.

M&L sheet glass 5.5mm thick ordinalry quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane complete all as specified and as directed.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and as directed.

S&F 100mm long aluminium anodized, barrel tower bolt of extruded section, complete all as specified and as directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.

S&F 100 mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.

S&F in repair aluminium (Die cast) body door closer hydraulically dessignation No 3 universal type suitable for door shutter of 851 to1000mm in width and weight 61 to 80 kg all as specified and directed.

S&F floor door stopper (Length of cover plate ) 150mm long aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor complete all as specified and as directed.

S&F 75mm long aluminium anodized, butt hinges of extruded section complete all as specified and as directed.

S&F 100mm long aluminium anodized, butt hinges of extruded section complete all as specified and as directed.

S&F100mm long mild steel butt hinges, medium weight cold rolled 100mm size complete all as specified and as directed.

S&F in repair 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and as directed

M&L for 25 mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate as in sub base of floor complete all as directed by Engr-in-charge.

M&L Non-Skid ceramic Coloured Tiles 7 to 8mm thick(squre/rectanglar) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors over 15 mm screed bed or bedding layers in cement mortar 1:4 Set and Jointed in neat Cement Slurry and Pointed in Colour Cement to match, complete all as specified and as directed.

M&L Light shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles including 15 mm thick screed in cement mortar (1:4) as in floors etc complete all as specified. Make : Johnson (Daisy SF/Gloria SF) or equivalent from Kajaria/Somany as approved by AO

M&L for 20 mm thick granite stone (any type) (table rubbed and polished) in steps, jambs, pillars, window cills, cooking plateform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite including cutting, etc and screed bed with CM (1:4) 20mm thick laying floor tiles complete all as specified and as directed.

Dismantling water tank exc 250 & n exc 500 litre and removing to store all as specified.

S&F rotational moulded polyethylene water storage tank (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 500 litres including all accessories, all as specified.

S&F 25mm bore stop cock chromium plated screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule, complete all as specified and as directed.

S&F 25mm ball brass valves, high pressure with polythene float and fly nut complete screwed for iron/PPR pipe and fixed in repair, complete all as specified and as directed.

S & F in repairs fancy type 15mm bore chromium plated bib taps, cast copper alloy, with crutch or butterfy handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing and connections and set aside for re-use or removal to store, complete all as specified and as directed.

Taking up or down 25/32 mm bore steel tubing and connections and set aside for re-use or removal to store, complete all as specified and as directed.

S & F 25mm dia 3 layer PP-R polypropyene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as per manufacture instructions and as directed by Engineer in Charge.

S & F 32mm dia 3 layer PP-R polypropyene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as per manufacture instructions and as directed by Engineer in Charge)

S & F in repair One Piece EWC with built in Cistern Vitreous china wash down water closet (Pedestal), white (EWC) including Plastic seat of same colour of WC, closed patttern with flat bottom, and cover and Mild steel chromium plated hinging device complete with flushing cistern, complete all as specified and as directed.

S&F15 dia angle stop valves, fancy type chromium plated with lonk shank and cup cast copper alloy , screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipes complete all as spd.

S&F PVC connectons 15 size with PTMT nuts (length 600mm), complete all as specified and as directed.

S & F in repair Vitreous China wash basin Fency type pedestal pattern , white, flat back, size 550 x 400mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe, complete all as specified and as directed.

S&F in repairs health faucet (ABS Body) mild steel shromium plated suitable for 15 mm dia with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S & F CP toilet jet spary ABS with double lock 1.2 mtr CP tube stainless steel flexible hose all as specified and as directed.

Supply & Fixing sheet glass shelf assembly consisting of 8mm thick glass shelf 300 x 300mm as in corners wide with bevelled edges/hatching of edges fixed with stainless steel 'D' bracket fixed and railing complete all as specified and directed.

Supply & Fixing sheet glass basin shelf assembly consisting of 8mm thick glass shelf 600 x 150mm wide with bevelled edges/hatching of edges fixed with stainless steel 'D' bracket fixed and railing complete all as specified and directed.

S&F in repair 15mm bore CP wash basin mixer for mixing hot & Cold water copper alloy fancy type high pressure screwed for iron pipe and fixed in repair, complete all as specified and as directed.

S & F in repairs 750 mm long, 32/ 40 mm dia., PVC flexible Waste pipe for sinks / wash hand basins, complete all as specified and as directed.

S & F in sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, Waste pipe including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed.

S & F in repairs, 40mm waste coupling of PTMT for sink and wash hand basin (Half or full threaded ) (Minimum Weight 45 grams), complete all as specified and as directed.

S & F in repairs, 32mm waste coupling of PTMT for sink and wash hand basin (Half or full threaded ) (Minimum Weight 45 grams), complete all as specified and as directed.

M&L for Cement concrete type D-2,1:4:8 (40mm graded aggreate) 75 mm thick as in sub -floors ,sub- bases ,floors and pavings,etc, complete all as specified and as directed..

M&L for Chequred cement concrete tiles (glazed) 30cm X 30cm X 20mm thick, set ,pointed & jointed in neat cement slurry in floors polished with grey cement & pigments .Layed over 20mm thick cement screed base (1:6) and all as directed by Engr-in - charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for angle iron or flat iron as in post and guard bars or grating, complete all as specified and as directed by Engr-in-Charge.

S&F MS Rolled sections in main and cross beams,hip and jack rafters ;purlins where connected to common rafters running rails and guids for sliding doors ;fixed with angle cleats or other connecting plates and similar work confirming to Fe-290, Gde-E-165 complete all as specified and as directed.

M&L preparation of new untreated steel surfaces exc. 10 cm width/girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

S&F Pre painted galvalumealuminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall fixed with self tapping screws, complete all as specified and as directed.

S&F Pre painted galvalumealuminium zinc coating GI based Plain steel sheet 0.50mm thick as in ridges , valley gutters drip etc of an colour having tensile strength of 550 Mps as in roof covering /cladding to wall fixed with self tapping screws as specified.

M&L for Reinforcement cement concrete (Nominal Mix) in type B1 1:2:4 ( 20mm graded aggregate) as in slabs supported of walls , beams and columns in floors, roofs, landings, balconices , canopies , deck slabs and in shelves etc complete all as specified and as directed.

M &L for form work to soffits of suspended slabs flat type such as roof slabs , floor slabs , landings and similar work nto exceeding 200mm thick (Horizontal or slopping etc complete all as specified and as directed.

M&L mild steel TMT bars 10mm dia and over, cut length, bent to shape required , including cranking , bending spirally for hooping for coloumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to TMT bar, complete all as specified and as directed.

M&L for preperation and removal of old Steel / CGI Sheet surface any description over 10cm in width or girth and applaying two coat of synthetic enamal paint all as specified and as directed complete all as specified and as directed.

S&F in repair 19mm dia mild steel, chromium plated curtain rods fancy type , with brackets, end bulbs all as specified and as directed by Engr-in-charge.

S&F chromium plated soap dish any type fixed to plugs with brass screws, complete all as specified and directed.

S&F in repairsTowel rail 600mm long Cromum plated (Minimum weight 190 gms), complete all as specified and as directed.

S&F in repairsTowel Hnager with 6 Nos of pin and 600mm long Cromum plated etc complete fitted as per sepcified and directed by Engr-in-charge

Demolition of Reinforced cement concrete in any description and any position not otherwise specifically provided for, complete all as specified and as directed

M&L for precast cement concrete Type B1, 1:2:4 (20mm graded aggregate) in landings, cover slabs (for manholes etc), chullah hoods, chhajja, water troughs, shelves and similar articles with plain faces, setting in CM 1:6, complete all as specified and as directed.

M&L for 15mm thick rendering on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 4 complete all as specified and as directed.

M&L for preperation of old plastered wall surface of any description and applying two coat of white wash complete all as specified and as directed.

S&F 2nd class soft wood plain, solid, straight chowkets and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as directed by Engr-in-Charge.

S&F mild steel work as in hold fasts and similar work confirming to Fe-290 or Gd -E 165 complete.all as specified and as directed by the Engr-in-Chage

Material & labour PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) as in hold fast , bed block and like complete all as specified and as directed by the Engr-in-Charge.

S&F for 35mm thick 2nd class hard wood plain framed factory made paneled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, Supply and fixed to chowkats , complete all as directed by Engr-in-charge.

M&L for preperation of old wooden surface surface any description over 10cm in width or girth and applaying one coat of synthetic enamal paint all as specified and as directed complete all as specified and as directed.

M&L for Non skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.06 Sqm and nexc 0.11 Sqm in floor etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the screed bed with CM (1:6) 15mm thick laying floor tiles complete all as specified and directed.

M&L for Glazed ceramic coloured tiles in vertical surfaces 350 x 250 x 7mm /450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match over 10mm thick CM (1:4) in dado/skirting tiles complete all as specified and directed.

S&F viterous China squatting pan or Orissa pattern 580 x 440 mm white with integral foot rest (excluding cistern) with front or back inlet ant pattern as in repairs incl bedding with PCC type B-I 1:2:4 , using 20 mm graded crushed stone aggregate.

PVC (SWR) 'S’ trap of 125/110 mm bore.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc. including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)

M&L for PVC (SWR) pipe single socketed, 110mm soil, waste and rain water dranage pipes laid in trenches or in floors and jointed all as specified.

S/F 75 mm dia (SWR) bend any redius complete all as spd

PVC (SWR) vent cowl of 75mm bore

M&L for PCC 1:4:8 TYPE D-2 (40mm gradded aggergate) bed to drain pipe incl packing under and hanching against side after they are laid and tested up to 110mm dia pipe including dismentling

M&L for PVC (SWR) pipe single socketed, 75mm dia soil, waste and rain water dranage pipes fixed to walls or laid in trenches/floors all as specified including dismantling etc .

S&F 0.63mm thick Galvanised corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers in roofs walls etc. with grade of zine coating 275, complete all as specified and as directed.

Demolition of stone/boulder masonry built in cement mortar including all quoins, arches , pillars etc and removing demolised material out of Military station all as specified and as directed.

M&L Walling of random rubble uncoursed stone masonry, uncoursed well bonded laid dry in retaining wall abutment and similar work.

M&L form work to rough finshed edges of concreat flats, treads breaks in floors, window cills, concrete failings, openings in concrete walls, floor and roofs n.exe 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20 cm wide, complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc.laid bedded and pointed in any mortar, complete all as specifed and directed.

Demolition of cement concrete (unreiforced) in any description and any position not otherwise specifically provided for, complete all as specified and as directed.

S&F for 30mm thick 2nd class hard wood plain framed factory made glazed and skeletion window/ventilator shutters , open rebated and prepared to receive glass , gauze etc (without sash bars) edges of framing plain , chamfered or rounded fitted with cut and mitred beds for securing glass etc size of members of shutters as specified in SSR part I, Section 8 , clause 8.24(a) supplied and fitted to chowkats , complete all as directed by Engr-in-charge.

S&F Structural steel works as in tubular roof trusses, purlins, Rafter, vertical posts, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, tubular pipe, channel or flat sections) including distance pieces, cleats , riveting incl bending and welding, conforming to Fe – 410W Gde E -- 250 quality A complete all spd and as directed.

M&L for pre cast cement concrete block masonary (except blocks) in CM 1:6, of 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) with soild blocks, using old concrete blocks obtained from the demolition, exc.10cm in width, set and jointed in cement mortor 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L PCC 1:3:6 typeC-2 (using 20mm graded stone agg) 75mm thick sub base, complete all as specified and as directed.

S&F 15mm bore cast copper alloy with capstan head chromium plated pillar tap screwed down high pressure with or without letter 'Hot' or 'Cold' with long screwed shank and fly nuts

S&F viterous China urinal half stall type white including CP spreader, waster pipe etc. complete all as specified and as directed.

S&F Vitreous china urinal partition white of size 310x700 mm, completed all as specified and directed.

S&F in PVC(HDPE) SWR 110 mm bore, single socketed in any length with rubber ring joints using solvent as per maunfacture instruction, laid in treches or in floor complete all as specified and directed by Engr-in-Charge. Make : Astral / Prince / Finolex

S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F in repairs 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S&F in repairs PVC(HDPE) SWR 75 mm bore, single socketed in any length with rubber ring joints using solvent as per maunfacture instruction, laid in treches or in floor complete all as specified and directed by Engr-in-Charge. Make : Astral / Prince / Finolex

M&L PVC (SWR) 75 mm dia floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

S&F grating doom 75mm dia of PTMT (min weight 25gms) complete as specified and directed, complete all as specified and as directed.

S&F in repair towel rod CP 60 cm long between flanges and including all accessories like brackets/screws etc as recommended by manufacturer and complete fixed in position complete all as specified.

M & L for machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over 15 mm screed bed or bedding layers in cement mortar 1:6 Set and Jointed in neat Cement Slurry including rubbing and polishing complete all as specified and directed by Engr-in-Charge

S & F in repair 10 ltrs capacity incl PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets including flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern, complete all as specified and directed by Engr-in-Charge.

S & F in repair 15mm bore angle stop valve standard of PTMT any color high pressure screwed for iron pipes and fixed complete all as specified and directed by Engr-in-Charge

S & F in repair Vitreous china urinal of size 320 x 300 x 520 mm white (minimum) complete including flush pipe and waste pipe, providing and fixing plugs, bedding urinal against wall in cement 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back fin cement fixing automatic flushing cistern with brackets flush pipe grating and union for discharge pipe complete all as specified and directed by Engr-in-Charge

S & F in repair tubular towel rail , 20mm dia 600mm long chromium fixed and including chromium plated brass screw and wooden/plastic cleats (min weight 270gms) D type 4, complete all as specified and directed by Engr-in-Charge

S & F rotational moulded HDPE water storage tanks 500 ltrs capacity and will be PUF insulated with 75mm thick PUF insulation of density 48 kg/Cum inner and out white two layers ISI marked ( cylindical vertical type/rectangular loft type closed top) hoisted hoisted with threaded cap and fixed in position all as specified in SSR Part I including all accessories (ie GI nipple etc), including provn of 20/25 mm dia spout for connecting inlet, outlet, over flow and washout pipes complete all as specified and as directed by Engr-in-Charge.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified and as directed by Engineer-in-Charge.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed by Engr-in-Charge

M&L for plain sheet glass 4.80mm thick ordinalry quality and glazing with oil putty or wooden beads in square or fixed with aluminium section including rubber beads not exc 0.50 sqm in each pane complete all as specified and as directed by Engr-in-Charge.

M & L for two coat of oil bound distemper on old decorated surfaces of walls incl prepartion of surface complete all as specified and directed by Engr-in-Charge

Excavating in post holes (or similar holes) each n exc 0.5 cum in hard/dense soil, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface.

M & L for cement concrete type C2 1:3:6 (40mm graded aggregate) in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts.

S&F framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles as necessary, gusset plates, cleats, MS Flat, MS plate, rivetting etc n.exc 10 kg each brackets, conforming to FE 290 Gde E-165.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard/dense soil.

M&L Hardcore with broken stone of gauge n exc 63 mm, deposited, spread and levelled and layer n exc 15 cm thick, water and rolled /rammed to a true surface.

M&L for Cement concrete type B-2,1:2:4 (40mm graded aggreate) 75 mm thick as in sub -floors ,sub- bases ,floors and pavings,etc.

Supply only metalic floor harderner

Removing excavated material not exceeding 50 mtr and deposting where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed

M & L for providing and fixing Gypsum boards 9 mm thick PVC film on the face side and other side metalised polyster flim as in ceilings fixed with screws as per manufacturers instructions including anodised aluminium powder coated snap grid frame work of size 605 x 605 mm with anodised aluminium channel supports/ angles/ 'T' (Main tee 35 x 25 x 1.5 mm, cross tee 25 x 25 x 1.4 mm and wall angle 32 x 32 x 2 mm) fixed with screws/ plugs etc including GI suspenders of 6mm dia upto 1200 mm length adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size as per approved pattern and design complete all as specified and directed by Engr-in-Charge.

M&L for 10mm thick teak wood finish laminated wooden flooring interlocked with each others and its size as directed,over 6 micron polyethylene sheeting over the concrete to minimize moisture migration from the concrete complete all as specified and directed by Engr-in-Charge. Make as per PS.

S&F wooden panelling on vertical surfaces of wall using the following specifications:- (a) S&F IInd class hard wood wooden gutties of size 25 mm x 25mm x 200 mm depth fixed in wall by making holes in brick wall and making good in cement mortar 1:3 (1 for cement and 3 for sand) (b) S&F Horizontal runner II nd class hard wood @ 1.20 mtr C/C of cross sectional area exc 13 Sqcm and 25 Sqcm clean swan with nails or screws, treated with two coats of cerosite oil mixed with good quality pesticide for antitermite treatment. (c) S&F IInd class hard wood boarding 12 to 15 mm with tongue and groove method of fittings as in wall panelling planed one side, and other side wrought fixed with screws. (d) S&F IInd class hard wood decorative beading 40 mm wide on top and bottom along perimeter of the wall or as specified. (e) M&L for French polishing on wooden surface any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats till the surface smooth/glossy complete all as specified and directed.

M&L for 2nd class softwood clean sawn as in scantling fixed with nails exceeding 13 Sqcm and n.exc 25 Sqcm in section

M&L for 2nd class softwood with plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads but bullnosed, splayed, chamfered or rounded on one edge or face,exc 3 sq.cm and n.exc 06 sq.cm

M&L for painting 2 coats of synthetic enamel paint over one coat of pink primer on both sides of door including preparation of old painted surfaces of any discription, not otherwise described all as specified

25 mm thick, plain cement concrete, 1:2:4(Nominal Mix), type B-0 (using 12.5 mm graded crushed stone aggregates) as in floors finished rough surface to receive floor finishes, complete all as specified and directed by Engr-in-charge.

M&L for two coat of acrylic emulsion distember over a coat of primer on plastered surface of any description,including preparation of new plastered surface complete all as specified and as directed.

M&L rendering 15mm thick in cm 1:6 concrete or brick surfaces as in wall finishes even andsmooth w/o using extra cement incl mixing of wpc .

M&L screed bed or bedding laying of cement mortar (1:6), 15 mm thick for as in floor finishes, complete all as specified and as directed.

S&F Soap dish fixed with and incl CP brass screws complete all a specified and directed (Make: Jaquar Cat No: AKN-35731P or equivalent approved make).

S&F chromimum plated brass 32 mm coupling for table top wash hand basin half or full thread fixed complete all as specified and directed. (Make: Jaquar Cat No. ALD-725 or equivalent approved make)

S&F PVC (SWR) 110mm bore junction single (single T), complete all as specified

S&F 75mm bore PVC (SWR) junction single, (Single T) equal or unequal

S & F Toilet paper holder with flat recessed type stainless steel complete all as specified and directed

S7F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms)

S&F in repair single piece china wash down water closet , with UF soft close seat cover, hinges, accessories set, cistern fittings size 370x690x795mm Make: jaquar Cat No. KUSWHT-358515N or equivalent approved make, complete all as specified and directed.

S&F wash hand basin table top type fixed on granite top grooving and cutting if required with long body pillar tap connection and partition boxes below complete all as specified and directed Make: Jaquar cat No SLS WHT-6011 or equivalent approved make

S&F in repair pillar tap single lever tall body with 150 mm extension body fixed on granite top for supply of hot or cold water fixeing with washers complete all as specified and directed. Make Jaquar Cat No. ARI 39005B or equivalent approved make

S&F in repair hand shower ( health faucet ) CP with 8 mm dia. 1.2 Metre long flexible tube and wall hook complete all a specified and directed. (Make : Jaquar Cat No. ALD-573 or equivalent approved make)

S& F Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms)

M&L 32mm Waste fittings, brass chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed

S&F in repairs stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed

S&F PP-R Gate valves 25 mm dia(brass insert) as per requirement of the site

S&F PP-R Ball valves 25 mm dia (brass insert) as per requirement of the site

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

S&F 110 mm dia PVC (SWR) junction single, (Single T) equal or unequal

S&F in repair Door closer hydraulically regulated designation No 3 universal type, aluminium body suitable for door shutters of up to 700 mm in width and weight not more than 35 Kg and fixed complete all as specified and directed.

M&L for factory made brown colour solid WPC (wood particle composite) door frame of size 100mmx63 mm single rebate 100% lead free made from single extruded process material with density 0.78 Kg/RM complete all as specified and directed.

Providing and fixing 30 mm factory made solid WPC (wood particle composite) moulded door shutter single extruded with 2,4 or 6 raised panel design on the front side with 10 mm deep mould on single side, with wood grain texture. The density of the door shutter not less than 600Kg/Cum shiuld be 100% lead free door complete all as specified and directed. Make ECHON cat No. LPD-11 or or equivalent approved make

S&F only 200mm long aluminium anodised barrel tower bolt of extruded section in old or new position

S&F in repairs 150mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F aluminum door handle cast type 150 mm in old or new position

S&F towel rack chromium plated brass fixed to walls with screws complete all as specified and directed. (Make: Jaquar Cat No. AKP-35781PS or equivalent approved make)

S&F glass shelf corner fixed on walls with screws complete all as specified and directed (Make: Jaquar Cat No: ACN-1173 or equivalent approved make)

S&F in repair chromium plated paper holder fixed on walls complete all as specified and directed. (Make: Jaquar Cat No: AKP-CHR-35753P or equivalent approved make).

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed by Engr-in-Charge.

S&F Powder coated (minimum thickness of powder coating 50 micron) anodised aluminium door shutters, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading screws etc. complete all as specified and directed by Engr-in-Charge.

S& F 1000 ltr capacity rotational moulded polythelene water storage tanks triple layer white colour (cylindrical vertical with clossed top) hoisted and fixed in position including dismantling all as specified in SSR Part 1 complete all as specified and directed .

Taking down carefully copper/aluminium point wiring (light, fan, socket and power point) complete fittings such as switches, ceiling rose, regulators, socket etc and removing material from site and making good disturbed surfaces of walls, floors/ceiling to match the existing surface all as spfd and directed by Engr-in-Charge.

Taking down care fully sub main wiring/service wire of any description complete all as specified and directed

Point wiring complete with 1.5Sq.mm nominal area of copper conductor multi stranded PVC insulated and unsheathed 1100 volts cable drawn through & including PVC Casing & caping with standard accessories such as elbows, tees, junctions etc. and PVC moulded terminal box with top cover of including PVC insulated unsheathed solid 1.5Sqmm copper conductor cable as continuous earth lead all as specified and directed for the followings:-

One light/exhaust fan point controlled by one way switch complete all as specified and directed

One switch socket outlet 6 Amps, 230 volts point on Same board complete all as specified and directed

One switch socket outlet 6 Amps, 230 volts point on independent board complete all as specified and directed

All as item No 188 above, but using cables 4 Sq mm size complete all as specified and directed

All as item No 188 above, but using cables 2.5 Sq mm size complete all as specified and directed

Supply and Fixing in replacement of lamp holder insulated body with back plate complete all as specified and directed

Supply and Fixing lamp holder insulated body with back plate complete all as specified and directed

Supply and Fixing in replacement of Switch piano flush button single pole 6 Amps 230 volts one way complete all as specified and directed

Supply and Fixing in replacement of switch Socket out let two in one 5 pin 6 Amps flush type.230 volts complete all as specified and directed.

Supply and Fixing in replacement of switch Socket combination out let multi purpose 5 pin 6 Amps and 16Amps 230 volts complete all as directed.

Supply and Fixing in replacement of Ceiling rose, surface Bakelite three terminals complete all as specified and directed.

Supply and Fixing Ceiling rose, surface Bakelite three terminals complete all as specified and directed.

Supply and fix in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 8 Ways complete all as specified and directed

Supply and fix sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 8 Ways complete all as specified and directed

Supply and fix in replacement of MCB SPN 63 Amp 240 Volts AC ISI marked all as specified and directed

Supply and fix in replacement of MCB SP 6-32 Amps. 240 Volts 50 HZ complete all as specified and directed

Supply and fix MCB SP 6-32 Amps. 240 Volts 50 HZ complete all as specified and directed

M & L for submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/recessed as required in PVC casing Caping wire size 2x6.0 sq. mm + 1x6.0 sq. mm earth wirecomplete all as specified and directed

Supply and Fixing in Replacement LED light fitting 1X20 W, 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed

Supply and fix in replacement LED luminaire 600mm x 600 mm, 35/36 watt,220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and Fixing in replacement connecting and testing LED security light fitting 35 watt, 230 volt, AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp and bracket with impact and corrossion resistant incl thermal management in multiple optics complete all as specified and directed

Material & labour for earthing with Galvanised Steel earth plate electrode 60cm x 60cm x 6.0 mm thick buried directly in ground vertically at a depth not less than 2.25metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, earth plate surrounded from all sides by 15cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using Galvanised Iron wire 4 mm as earthing lead (upto terminal point) by means of bolts, nuts, check nuts and washers made of galvanised iron and thimbles and protected by light grade 15 mm dia GI pipe connected to main switch board or main control board and GI pipe medium grade 20mm bore for watering and including funnel , wire mesh , RCC pit cover and PCC chamber pit with PCC (1:3:6) type C-2 using 40mm graded stone aggregate, including excavation and earth work in any type of soil , returning , filling in approved soil and disposal of surplus soil to a distance not exceeding 50m all as specified and shown in electrical plate No 3 of SSR 1991(Part-I) Taking out old unserviceable earthing complete all as specified and directed. NOTE : - The rates for earth work, GI protection pipe, funnel, wire wesh, CI cover, etc shall be deemed to be including in quoted rates.

Supply and Fixing in replacement Air Circulator , steel body AC single Phase 230V of size 300mm with Electric driver , blades, and frame and louvers complete all as specified and directed

Supply and Fixing Air Circulator , steel body AC single Phase 230V of size 300mm with Electric driver , blades, and frame and louvers complete all as specified and directed

Supply, Laying, jointing and testing in replacement PVC insulated armored heavy duty electric cable with aluminum conductor, 1100 volt grade, cross sectional area 16 Sqmm 2 Core. complete all as specified and directed.

Excavating in trenches not exceeding 1.5 m wide and not exc. 1.5 mtr in depth and getting out in anay type soil and making good excavated surface complete all as specified and directed.

Supply and spreading sand for cusioning of electric cable complete all as specified and directed.

Supply and laid Un-reinforced precast concrete cable cover class LV 1 flat size 250 mm x 150 mm x 40 mm complete all as specified and directed.

Returning, filling in including spreading levelling watering and well ramming in layer not exceeding 25 cm complete all as specified and directed.

Supply and fix in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 12 complete all as specified and directed.

Supply and fixing of sheet metal enclosure with 20 Amp 240 V socket plug top and MCBs single pole and neutral enclousre with two pin and earth plug and socket with one single pole 20 Amp MCB complete all as specified and directed.

Supply, install, testing complete water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 Litre, BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipes etc complete all as specified and directed.

Taking down old unserviceabole exhaust fan and supply and fix in repair exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed.

M & L for submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/recessed as required in PVC casing Caping wire size 2x 2.5 sq. mm + 1x 2.5 sq. mm earth wire complete all as specified and directed.

Supply and fix LED down light ( round, Coll white ) of capacity 15 Watt, motion sensing based with 4.5 mtrs radius, 215 Volts complete all as specified annd directed.

Supply and fix in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 4 Ways all as specified and directed by Engr-in-Charge.

Supply and laying of XLPE insulated, armoured, haeavy duty electric cables (heavy duty) with stranded aluminium conductor rating 1100 volts grade of size 16 Sqmm 4.0 core laid in trences or passing through pipes.ducts or fixed to walls/poles completer all as specified.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core

M& L 40 mm GI Pipe light grade for cable protecton in road crossing and making good surface road to filling with PCC complete all as specified and directed by Engr in Charge.

S & F decorative durable LED batten fitting of 18/20W , 4 feet long with decorative and caps, powder coated CRCA decorative for LED tube of any capacity, 4 feet long (white colour) tube having driver ,connector block etc complete with all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 Sqmm 3 core all as required at site or directed by Engr in Charge.

S&F LED Mirror light fitting of 9/10 W and type 230 volts box type , with standard specification etc complete withh all accessories pre wired twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed .

Supply and Fix 7 watt LED bulb all as required at site or directed by Engr-In-Charge. Make:- Havells or Eqvt in Philips/Bajaj/Wipro/crompton

S&F MCB SPN 6 to 32 Amps 240 Volts. Make : Iegrand /L&T

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed .

Deduct Schedule of Credit of Rs (-) 96213.00 (Minus) as listed in Schedule 'A' (Contd). Contract Sum shall be arrived after deducting the credit amount. Note :- Tenderers will not quote against this item being a firm amount.

M/S INDUS HIMALAYAN EXPLORERS (BID ID -3345419)

R B TRADERS (BID ID -3362473)

TSEWANG DORJAY (BID ID -3361863)