PROVN OF COVERED SHED ON TRAINING STORES TERRACE OF 154 INFANTRY BATALLION (TA) BIHAR AND ADDN/ ALTN TO TOWER POST NEAR BDE MAG IN ZONE - 4 AT BRICHGUNJ MILITARY STATION, PORT BLAIR

Amount

Surface dressing not exceeding 15cm deep and getting out in soft / loose soil soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5M wide and not exceeding 1.5M in depth for foundation, laying pipe line, replacing sluice valve etc and getting out in soft / loose soil complete all as specified and as directed.

Excavation in trenches, not exceeding 1.5 M wide and exceeding 1.5 M and not exceeding 3.0M depth for foundation, laying pipe line, replacing sluice valve etc, and getting out in hard/ dense Soil.

Excavation over areas, n exc 1.5m deep for foundation etc & getting out hard/dense soil all as specified.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft / loose soil including making good of disturbed surfaces complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Material & Labour for Moorum/ Red Bajri Filling in floors or pavings, laid in layers n exc 15cm thick, spread, levelled and rammed including watering and complete all as specified and as directed.

Material and labour for hard-core of gauge not exceeding 63 mm of broken granite stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

Material and labour for treating the bottom & sides of excavation @ the rate of 5 Lit of emulsion per sqm of surface area complete all as specified and as directed.

Material and labour for ATT on top of earth filling @ 5 lits/sqm of emulsion complete all as specified and as directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing the rubbish off the premises.

Demolition of reinforced Cement concrete for Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work etc all as specified and directed

Material and labour Broken Brick bats gauge 80 to 150mm Loose filling in soakage pits, soakage wells complete all as specified and as directed.

Material and labour 25mm thick cement concrete type B-0 (12.5mm graded stone aggregate) as in RCC roof / Floor surface wfor level coarse

Material and labour 80mm thick PCC(1:2:4) type B2 using 20mm graded stone aggregate as in flooring finished even and smooth using extra cement.

Material and labour for precast cement concrete solid block masonry with solid blocks using PCC 1:3:6 type C1 using 20mm graded stone aggregate n.exc 10cm in width and setting in cement mortar (1:4) etc complete all as specified.

Material and labour Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed.

Material and labour precast cement concrete block masonry with PCC solid blocks in 1:3:6 type C1 using 20mm graded stone aggregates, exc. 10cm in width and set in CM 1:4 complete all as specified and directed.

Material and labour Precast cement concrete Type B1 1:2:4, (20mm graded stone aggregate ) in cover slabs chajjas, sunshade, shelves and set in cement mortar 1:4 complete with joints to match all as specified.

Material and labour for Reinforced cement concrete M30 (design mix) in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified.

Material and labour for Reinforced cement concrete M30 (design mix) in columns, pillars, piers, posts and struts etc complete all as specified.

Material and labour for Reinforced cement concrete M30 (design mix) in Beams, cantilevers, bressumers, lintels over 1.5m span, complete all as specified.

Material and labour for Reinforced cement concrete M30 (design mix) in Chajjas complete all as specified.

Use and waste for form work to sides of rough finished concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits if any of foundation and plinth beams and similar work vertical or to batter complete all as specified and as directed by Engineer in Charge.

Use and waste for form work to sides of Pillars, posts, struts, piers, columns and sanctions complete all as specified and as directed.

Use and waste for form work to sides and soffits of rough finished floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc alos splays between floors, and beams, etc compelte all as specified and as directed by Engineer in Charge.

Use and waste for form work to chullah hoods, chajjas, troughs and similar items including edges, etc complete all as specified and as directed by Engineer in Charge

Material and labour for TMT bars 10mm dia and over as in reinforcement cut to length, bent to shape required including cranking hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing clips

All as per item No 28 here in before but 6 mm to 8mm dia.

Material and labour for TMT bars 5mm dia and over upto and incl 10mm dia in stirrups, spacers, and binders in reinforcement cut to length, bent to shape required including cranking hooking ends and binding with mild steel wire.

Supply and fix plates (Plain or chequered), channels, square cut or notched (ordinary and counter sunk) forming holes with attachment etc and fixed by riveting or welding or with nut and bolts (including nut and bolts) conforming to Fe- 410-W Grade E- 250, quality B, complete all as specified and as directed.

Supply and fix MS Steel work in tubular trusses and tubular posts/ purlins including special shaped washers etc., complete using ERW or induction butt welded tubes conforming to IS :1161-1979 grade st-240 including notching, drilling, fitting, riveting and/or welding or connecting with bed plate, bolt and nuts complete all as specified and as directed

Supply and fix Mild steel Bolts Exceeding 12mm n. exceeding 20mm dia, purpose made with Hexagonal or Square head one end and screwed the other, or Screw both ends, each screwed end to be fitted with Washers and one hexagonal or Square nut, Exceeding 30 cm long all as specified and directed.

Supply only water proofing compound

Material and labour for rendering 10mm thick on fair faces of brick/concrete surface in CM (1:6) finished even and smooth without using extra cement.

Material and labour for 15mm thick external rendering in two layers of 5mm thick in CM 1:4 mixed with water proofing compound (water proofing compound shall be used @3% weight of cement) over a coat of 10mm thick in CM (1:6) over brick or concrete surfaces finished even and fair. Note: Supply only WPC will be measured and paid separately

Material and labour for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished fair and even and smooth without using extra cement mixed with water proofing compound all as directed. Note: WPC shall be measured and paid separately.

Material and labour for oil bound distempering two coats over a coat of alkali resistant priming paint including preparation of new plastered or unplastered surfaces of wall complete all as specified and directed by Engineer - in -Charge.

Material and labour for preparing new steel/iron surfaces of any description exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer.

Material and labour for two coat of weather proof exterior acrylic emulsion paint with anti-fungal property over a coat of primer and a coat of external wall putty on newly plastered wall surfaces including preparation of surfaces etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for false ceiling with aluminium grid work (Size of grid 600x600 mm) with 35 x 25 x 1.5 mm main tee and 25 x 25 x 1.4 mm cross tee and wall angle and suspended with 2mm dia GI wire hooked to roof with needful adjustment bolts at an interval of 1.20 m centre to centre staggered and board with Eco board decorative type size 600 x 600 x 4 mm thick finished with two coats of oil bound distemper over a coat of primer on exposed surfaces all as specified and directed by Engineer-in-Charge.

Material and labour Coloured Non-Skid Ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floor etc, set and jointed in neat cement slurry and pointed in coloured epoxy to match as in floor over and including 20mm thick screed bed in CM (1:6).

Material and labour Glazed ceramic tiles coloured 350x 250x7 or 450X 350X 7mm thick on vertical surfaces such as skirting, dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick in CM 1:3 as backing coat for fixing dado tiles all as specified.

Material and labour non-skid ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm and not exceeding 0.38 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured tiles over and including 15mm thick screed bed in CM 1:4

All as per item No 44 here in before, but on vertical surfaces including 10mm thick CM 1:3 as in baking coat of dado/skirting

Supply and fix 0.50 mm thick pre painted galvalum aluminium zinc coating GI based plain steel sheet of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall or as in ridge fixed with self-taping screws as specified.

Supply and fix pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self-tapping screws etc complete.

Supply and fix Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing

Supply and fix Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

Supply and fix Aluminium anodised barrel tower bolt of extruded section of size 150mm long

Supply and fix 150mm long extruded aluminium alloy anodised handles fabricated type

Supply and fix Butt hinges, Size of hinge 100MM extruded brass, with mild steel hinge pin, bright polished and fixed, type B-21

Supply and fix Aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) 300 mm long and fixing clips of sheet cast or extruded sections and fixing bolt or cast aluminium alloy& fixed complete .

Supply and fix Aluminium anodised (minimum anodisation is 15 microns) Door / window / Ventilator/partition frames and shutters (02 Nos glazed & gauzed), side hung type, without sash bars, standard aluminium grills, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, locking arrangements etc., complete with standard aluminium sections, complete all as specified and as directed by Engineer-in-charge.(Aluminium section shall be of make Jindal/Hindalco/ Indalco).

Supply only 4 mm thick sheet glass ordinary quality and glazing with rubber packing around the glass, in squares not exceeding 0.50 sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

Supply only 4 mm thick sheet glass ordinary quality and glazing with rubber packing around the glass, in squares exceeding 0.50 sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

Supply only 12mm thick pre-laminated particle board, exterior grade, lamination on one side with decorative choice lamination and the other side balancing white lamination fixed with screws as in door panel, complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 4 mm thick sheet figured glass and glazing with rubber packing around the glass, in squares exceeding 0.50 sqm in each pane complete all as specified and as directed.

Supply & fix aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40 mm complete all as specified and as directed by Engineer-in-Charge

Supply and fix of stainless steel gratings 100mm dia, complete all as specified and as directed by Engineer-in-Charge

Supply and fixix 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed, minimum weight 142 gms, complete all as specified and directed by Engineer-in-Charge

Supply and fix of Bib tap cast copper alloy chromium plated 15mm dia with fancy type screwed down screwed for iron pipe or brass ferule etc complete all as specified and as directed by Engineer-in-Charge

Supply and fix chromium plated hand shower (health faucet) 1 meter, with PVC tube with wall hook , complete all as specified and as directed by Engineer-in-Charge. (Make : Jaquar cat No ALD-CHR-593)

Supply and fix wash hand basin of size 630X426X160mm including all fittings and bracket etc of Jaquar Cat No. JDS-WHT-25901 complete all as specified.

Supply and fix water closet pan (pedestal pattern) white, os size 360X680x775 mm with S trap 220mm of Jaquar Cat. No. CNS WHT -755SN and with flushing Cistern & fittings of Jaquar Cat.No. CNS WHT -755SN , 755SS, 755 PS, and 755 PN complete all as specified

Supply and fix of PVC connection 15mm size with CP brass Nuts of length 450mm complete all as specified and as directed by Engineer-in-Charge

Supply and fix PVC (SWR) vent cowl 110mm bore complete all as specified and as directed by Engineer-in-Charge

Supply and fix PVC (SWR) bends any radius 110mm bore complete all as specified and as directed by Engineer-in-Charge

Supply and fix 75 mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and as directed by Engineer-in-Charge

Supply and fix 25 mm bore GI tubing medium grade laid in trenches / floor or fixed to wall in any length with screwed and socket joints together with all galvanised GI fitting such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc and pressure testing, washing out complete all as specified and directed

Material and Lobour for 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors

Material and labour for 15 mm bore unplasticised PVC pipes of pressure rating 10 Kgf/Sqcm fixed complete to walls, ceilings or in floors etc any type of pipe all as specified and as directed.

Material and labour for cutting existing 50mm GI line and making branch connection of 40 mm dia GI line complete all as specified and directed

Supply and fix rotational moulded polyethylene water storage tanks 1000ltrs capacity (cylindrical or vertical with closed top) hoisted and fixed in position, complete all as specified and directed by Engineer-in-Charge

Material and labour for 20 mm bore unplasticised PVC pipes of pressure rating 10 Kgf/Sqcm fixed complete to walls, ceilings or in floors etc any type of pipe all as specified and as directed.

Supply and fix for 20 mm dia bore gun metal , globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

Supply and fix 25 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed, complete all as specified and as directed

Supply and fix 25 mm bore Gun Metal gate valve with iron wheel head ISI Marked screwed both ends suitable for GI tubing complete all as specified and directed

Supply and fix of stop valves cost copper alloy, screwed down, high pressure, with fancy type, chromium plated, screw both ends for 15mm dia iron pipe or for union and fixed.

Supply and fix Towel rail 600mm long & including Chromium plated brass screws & wooden / plastic cleats (Minimum weight 190gms) complete all as specified and directed

Supply and fix of brass, chromium plated toilet paper holder fixed to walls with chromium plated brass screws.

Supply and fix Chromium plated 125mm shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed

Supply and fix PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed

Material and labour Point wiring complete with 1.5 sqmm single core FRLS PVC insulated and unsheathed cable 1100 volts grade with multistranded copper conductor drawn through and including PVC casing and caping and all accessories fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm copper cable as earth continuity conductor and connected to common earth dolly, including fabricated steel terminal box made out of 1.60mm thick MS sheet concealed in walls, with 3mm thick laminated sheet top cover/Pre moulded PVC switch board for housing the switches, socket outlets, fan regulators etc., all as specified and as directed for One light point controlled by one way switch

All as per item No 85 here in before but One 3 pin switch socket outlet point 5 amps on independent board.

Supply and fixing in replacement of switch piano flush type single pole one way 5 Amp all as specified and directed.

Supply and fix switch socket outlet 3 & 2 pin (mult pin) 5 amps flush/box type, complete all as specified and as dircted by Engineer-in-Charge

Supply and fix ceiling rose surface Bakelite 65 x 50 mm 3 terminal, complete all as specified and as directed by Engineer-in-Charge

Supply and fixing energy efficient LED Smart bright batten 22 watt fitting 4ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours including lamp and connecting with twin core sheathed cable from fitting to ceiling rose all as specified and as directed.

Supply and fix Wall mounting fan electric driven single phase230 volts, oscillating type, 400 mm sweep, high quality with high speed motor and balanced blades and three leafed with 3 core copper cable of suitable size, complete all as per specified.

Supply and fix metal enclosure distribution board SPN, 4 way 240 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs, complete all as as specified and as directed by Engineer-in-Charge . Note:- Incoming & Outgoing connections from the DB shall be provided with proper lugs/thimbles etc...

Supply and fix MCB single pole 240 volts, 0.5 to 32 amps complete all as specified and as directed by Engineer-in-Charge

Supply and fix MCB SPN, 240 volts, 6 to 32 amps C series complete all as specified and as directed by Engineer-in-Charge

Material and labour for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Meter below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts, check nuts and washers of GI and GI tubing 20 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed electrical plate No. 3 of SSR part - I

RPG AND COMPANY

Bharat Udyog

M/s Kamal Electrical

SK CONSTRUCTION

Ravi Enterprises

M/s Ramesh Lal

S K ENTERPRISES

P Babu

RS ENGINEERING WORK