Renovation works in A-type quarters at BEL Township PKL

Amount

Disposal of moorum/building rubbish/ malba/similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.With cement mortar 1:4 (1 cement : 4 fine sand)

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All works : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 cement : 3 coarse sand (zone-iii) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand)

Providing and fixing Mapson nexan omega long body water tap for modular kitchen & batheroom Bib tap faucet (wall mount installation type)

Providing and fixing Hindware Basin area angle valve addons F860007- CHROME

Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall 25 mm nominal dia Pipes

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalentdesign mix)

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels Granite stone slab of all colour and texture except black, Cherry/Ruby red Area of slab over 0.50 sqm

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in ll shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink without drain board 610x460 mm bowl depth 200 mm

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: Stainless Steel AISI-304(18/8) Round basin 405x355 mm with single 15 mm C.P. brass pillar tap

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32 mm dia

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Structural steel work riveted, bolted or welded in built up sections, trusses and frame work, including cutting, hoisting, fixing in position with necessary wooden/steel scaffolding including providing applying two or more coats of synthetic enamel painting over a coat of approved steel primer all complete.(Note: The Basic rate of Structural Steel is considered as Rs 70.00 Per Kg)

Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge.

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm. Basic price of vitrified tile is Rs 550/m2

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.( Basic price of tile is Rs 500 per sqm)

Centering and shuttering including strutting, propping etc. and removal of form for lintels,Suspended floors, roofs, landings, balconies and access platform etc

Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and breaks in floors and walls Under 20 cm wide

Providing Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete at all levels. Thermo-Mechanically Treated bars of grade Fe-500D or more ( Basic price of Reinforcement Steel is considered as Rs 65.00 per Kg)

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing 100 mm inlet and 75 mm outlet PVC trap with stainless steel grating (with or without hole for PVC waste pipe of CHILLY/NOWAY make) including the cost of cutting and making good the walls and floors.etc.,Complete as per directions of Engineer-in-charge.

Providing and fixing 75mm dia PVC soil waste and vent pipe conforming to IS:13592 of SWR quality of 6kg /cm2 pressure including all fittings, like EG : Bends, Tees, Elbows, Collars, junction, inspection doors, cowls, offsets, access pipes, jointing with rubber ring / solvent cement by application of leak proof adhesive like FRP paste including cutting holes in walls and floors and making good.

Providing and fixing 110mm dia PVC soil waste and vent pipe ( including specials) conforming to IS:13592 of SWR quality of 6kg /cm2 pressure including all fittings, like EG : Bends, Tees, Elbows, Collars, junction, inspection doors, cowls, offsets, access pipes, jointing with rubber ring / solvent cement by application of leak proof adhesive like FRP paste including cutting holes in walls and floors and making good.

Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer-in-Charge.(a) Internal Work- Exposed on wall

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing Overhead shower with long shower arm Make Jaquar Model: (SHA-CHR-555) including fittings etc. complete

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:3 (1 cement :3 coarse sand)n 7.5 in foundations and plinth in :cement mortar 1:4 (1 cement : 4 coarse sand)

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Providing & applying Alkaline rust converting primer APCOREP RUSTREM in two coats conforming to ASTM-B-117 & ASTM-G-60-86 to exposed exiting rebars after removing & cleaning loose rust by wire brush and laeave it for 6-8 hours. The rust converter shall have a minimum pH of 7.5 and shall be able to convert both hematite and magnetite form of rust shall pass 400 alternate immersion cycle in 3.5%NaCL.

Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine sand):Flush / Ruled/ Struck or weathered pointing

Finishing walls with Acrylic Smooth exterior paint of required shade :Old work (One or more coat applied @ 0.90 ltr/10 sqm).

Supplying and fixing of black / gray rigid PVC pipe medium class Diplast or equavalent make 25mm (1" inch) of size with wall thickness as per IS including accessories like bends / junction boxes / elbows etc., and laying the same as recess/ surface conduit system in wall /ceiling /column etc. as required and makeing the wall as good as before laying of conduit or directed by engineer in charge complete in all respect.

Supplying and wiring with the following size, FRLS 660 / 1100 V grade PVC insulated single core, multi stranded copper wire in existing conduit as required and directed. Make finolex / KEI Size 1x1.5 Sqmm 660/1100 Volt Grade

Supplying and wiring with the following size, FRLS 660 / 1100 V grade PVC insulated single core, multi stranded copper wire in existing conduit as required and directed. Make finolex / KEI Size 3x2.5sqmm 660 / 1100 V grade

Supplying and wiring with the following size, FRLS 660 / 1100 V grade PVC insulated single core, multi stranded copper wire in existing conduit as required and directed. Make finolex / KEI Size 3x4.0 sqmm 660 / 1100 V grade

Releasing 3 /4 " to 1 1/4 " dia PVC/MS pipe along with all accessories and returning it to stores and stacking all as directed.

Releasing All type of wires up to 6.0 sqmm along with all accessories and returning it to stores and stacking all as directed.

Releasing All type of switch boxes/ mcbdb along with all accessories and returning it to stores and stacking all as directed.

Releasing All type of switch/socket/tube lights/batten holders/ mcb etc.of .any make along with all accessories and returning it to stores and stacking all as directed.

Supply and fixing of following size of Modular GI boxes:- 4 module (125mmx75mmx60mm)

Supply and fixing of following size of Modular GI boxes:- 6 module (200mmx75mm x60mm)

Supply and fixing of following size of Modular GI boxes:- 8 module (225mmx75mmx60mm)

Supplying of 3.0 mm thick hylam backed white PVC or coloured sheets cut to required size making holes / cutouts for fixing the switch / sockets / starters etc., as required and fixing the same on the already mounted MS box by using good quality screws with cup washers etc., all as required and or as directed by Engineer - in -charge.

Supplying and fixing of following piano type switches/ sockets fixing on existing switch boxes making electrical connection complete as required by engineer in charge. complete as required.make anchor S.P switch flush type 5 A , 250 V.

Supplying and fixing of following piano type switches/ sockets fixing on existing switch boxes making electrical connection complete as required by engineer in charge. complete as required.make anchor S.P switch flush type 15 A , 250 V.

Supplying and fixing of following piano type switches/ sockets fixing on existing switch boxes making electrical connection complete as required by engineer in charge. complete as required.make anchor Socket flush type 3 pin 5 A ,250 V universal type

Supplying and fixing of following piano type switches/ sockets fixing on existing switch boxes making electrical connection complete as required by engineer in charge. complete as required.make anchor Socket flush type 3 pin 15 A ,250 V universal type.

Supplying and fixing of following piano type switches/ sockets fixing on existing switch boxes making electrical connection complete as required by engineer in charge. complete as required.make anchor Telephone socket

Supplying and fixing of following piano type switches/ sockets fixing on existing switch boxes making electrical connection complete as required by engineer in charge. complete as required.make anchor Antena socket

Supplying and fixing batten holders of approved make and fixing the same on junction box by using good quality screws complete as required.make anchor

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way , Double door

Supplying and fixing 5 amp to 32 Amp rating Double pole 10 KA c curve mcb suitable for inductive load in the existing MCBDB complete with electrical connections testing and commissioning etc. complete as required

Supplying and fixing 5 amp to 32 Amp rating 240 volt single pole 10 KA C curve MCB suitable for inductive load in the existing MCBDB complete with electrical connections testing and commissioning etc. complete as required

Earthing with GI earth plate 600mmx 600mmx6mm including assessoriesincluding massonery enclosure with cover platehaving locking arrangement and watering pipe2.7mtr. with funnel including charcol/coke and salt as required complete inall respect as required by engineer in charge.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge 25mm average thickness

Finishing walls with water proofing cement paint of required shade :New work (Two or more coats applied @ 3.84 kg/10 sqm)

Supply and Apply Injection Grouting procedure with PU injection.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge..All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift.

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm.(b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm.(c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around.(d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately.For the purpose of measurement the entire treated surface will be measured.

pyramid builders (BID ID -417887)

Irfan Ahmad (BID ID -417932)