Repair and renovation of toilets including repair / retrofitting the gallery above toilets at Open Air Theatre.

Amount

SCHEDULE A

Dismantling the toilet block in each floor (Gents /ladies toilet) (Payment for dismantling all the toilet in block Ladies and Gents toilet ) including removal of all concealed fittings, removing concrete in sunken potions, fittings, doors , removal of floor and wall tiles etc and disposing the rubbish / debris within a lead of 150m and lift of 15m. Dismantling of the existing roof with RCC

Demolishing Brickwork including stacking of serviceable material and disposal of unserviceable material within 50m lead. In cement mortar

Demolishing cement concrete manually/by mechanical means including disposal of material within 50metres lead as per direction of Engineer-in-charge.Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Supplying and filling plinth with quarrty dust unde floors including watering,ramming,consolidating and dressing complete

Supplying and filling in plinth with river sand/ M-Sand under floors including watering, ramming, consolidating and dressing complete

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing polymer modified mortar of CM 1:4 of 30 mm in two coats ( each coat of 15mm thick) admixed with Nitobond SBR @ 6lts per bag of cement including applying a polymer based bonding agent Nitoband SBR @ 1:1:4 ratio on the plastered surface ( one part of Nito bond AR one part of water and four part of cement)- This is for the walls and floor

Supplying and applying two part flexible cementitious water proof coating / bonding agent manufactured by FOSROC/ BASF/ SIKA / FAB CHEM ( for 1.50 mm thick film at a coverage of 2.6kg/sqm - in 3 coats) including necessary surface preparation etc., complete as per specifications

Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in : Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS :12894, in super structure above plinth and upto floor V level. Cement mortar 1 : 3 (1 cement : 3 coarse sand)

Supplying and fixing LDPE black color sheet of 400 microns thick for laying the concrete.

Centering and shuttering including strutting, propping etc. and removal of form work for :Columns, piers, abutments, pillars, posts and struts

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin- charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding. Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Providing M-35 grade concrete instead of M-25 grade BMC/RMC. (Note : Cement content considered in M-35 is @ 380 kg/ cum) : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering,shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works above plinth level upto floor V level

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade. Area of slab upto 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

TECHNICAL SPECIFICATION / WORK METHODOLOGY FOR MICRO- CONCRETE/ NON-SHRINK CONCRETE 1. The affected concrete member shall be cleaned thoroughly by wire brush cleaning and washed with copious amount of water by high pressure water-jetting. 2. Exposed reinforcement bars – if corroded shall be cleaned by manual wire-brush cleaning and applied with Concresive ZRi – Epoxy Zinc rich primer or NITO ZINC (fosroc) as per the Technical and application recommendations of the manufacturer and allowed to dry for atleast 24 hours. 3. Supplying and Applying Concresive 1414 / Nitobond EP – Epoxy based Bonding Agent over the above prepared Concrete using a stiff brush as per the Technical and Application recommendations of the manufacturer. 4. Supplying and Pouring Emaco S46T / Rendroc HB2 – Cementitious Non-shrink, Micro Concrete into the erected formwork, for a nominal thickness of 50mm and whilst the above Bonding agent is tacky, and as per the Technical and Application recommendations of the manufacturer. 5. The formwork/shuttering shall be removed the next day and cured by placing wet hessain bags over the treated member.

Providing and fixing Galvashield XPi embedded galvanic anodes shall be pre-manufactured with nominal [add zinc mass] of zinc in compliance with ASTM B418 Type II cast around a pair of uncoated, non-galvanized steel tie wires and encased in a highly alkaline cementitious shell with a pH of 14 or greater. The anode unit shall contain no intentionally added chloride, bromide or other constituents that are corrosive to reinforcing steel (refer to ACI 562- 13, Section 8.4.1). Anode units shall be supplied with integral unspliced wires with loop ties for tying to the reinforcing steel.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :Second class teak wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) Second class teak wood - 35 mm thick shutters

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. With cement mortar 1:4 (1 cement : 4 fine sand)

Proving and laying Brick jelly Concrete 1:3:6 mix using 20 to 40 mm brick jelly in layer not exceeding 15Cm in Toilet Sunkan Portion With Contractors Materials,Labour,Tool,and Necessery lead,lift,Curing Etc Complete as per the Specfication.

Providing and fixing 8mm tk acrylic sheet after necessary buffing to make it opaque for urinal partition with SS brackets, Clamps Size 0.60x1.22m etc. complete as per the direction of Engineer in charge.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and fixing Ist quality Vitrified glazed wall tiles of size 600mmx1200mm conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing of aluminum colour powder coated (20 micron) ornamental grill for window using 50x50mmx6mm size opening fixed on aluminum frame with heavy duty aluminum U channel with all-round of grill and the rate including labour and material. (the rate of frame will be paid seperately)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Providing and fixing of Brass Cylindrical Lock of Godrej make with necessary screws and bolts etc. complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10mm dia. Bolts, nuts and wooden plugs and embeddings in cemnet concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate - 20mm nominal size).

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 250x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Interior painting: (two or more coats over a primer coat including complete scraping, other surface preparation like removal of loose paint residuals, damaged plastering, repairs to plaster, white cement based (JK / Birla) touch up putty / primer and making good the wall surface etc) Applying interior paint of approved colour, make, brand and product at the approved rate of surface coverage of painting as per Annexure A.1.3. The interior paint shall be applied over dry surface after complete scraping and removal of all loose or defective paint or powdery residue using mechanical methods with Zero dust vaccum technology followed with sealing the surface with a coat of approved interior primer before application of top coat of exterior paint. The contractor shall also carryout necessary surface preparation including removal of loose plastering, patch plastering, crack filling, micro-concreting, application of damp proof coating and making good the wall surface etc wherever required before applying primer coat. The contractor should ensure complete covering of floors using tarpaulin / plastic sheet while taking up the work. The work shall be executed as per the detailed specifications and special conditions mentioned in the Annexure A 1.3. The rate quoted shall be inclusive of charges towards all labour, material, transport, scaffolding, safety arrangements, Personal Protective Equipments (PPE), tools and plants etc.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Exterior painting: (Fresh work including complete scraping / surface preparation, as appropriate base (primer) coat and top two or more coats). Applying exterior paint of approved colour, make, brand and product at the approved rate of surface coverage of painting (As per Annexure A.1.1). The exterior paint shall be applied over dry surface after complete scraping and removal of all loose or defective paint or powdery residue using mechanical methods with Zero dust vaccum technology followed with High pressure Jet washing and sealing the surface with necessary exterior base coat or primer before application of top coat of exterior paint. The contractor shall also carryout necessary surface preparation including removal of loose plastering, patch plastering, crack filling, micro-concreting, application of damp proof coating and making good the wall surface etc wherever required before applying base or primer coat. The contractor should ensure complete covering of floors using tarpaulin / plastic sheet while taking up the work. The work shall be executed as per the detailed specifications and special conditions mentioned in the Annexure A 1.1. The rate quoted shall be inclusive of charges towards all labour, material, transport, scaffolding, safety arrangements, Personal Protective Equipments (PPE), tools and plants etc but excluding the cost of waterproofing, attending to leakages and major civil repair works if any. The Paint manufacturer shall inspect the work in every stage, submit inspection / field test report, certify the product / application and give 10 year Guarantee.

Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) with precast R.C.C. vertical grating complete as per standard design :

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) SFRC cover with CI frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Schedule B (Sanitary ware and CP Fittings:)

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan.

Providing & fixing white vitreous china water less urinal of size 600 x330 x 315 mm having antibacterial /germs free ceramic surface, fixed with cartridge having debris catcher and hygiene seal.

Providing and fixing wash basin (counter top or counter bottom) (Somany -Oval type 460x342x155mm square type 515x380x120mm / circular 445x445x 195) with making good the walls etc complete. White Vitrous china wash basin 550mm excluding cost of fittings. ((Parryware / Hindware/ Somany)

Supplying and fixing Health faucet with Flexible tube, wall hook, 15mm CP angle valve etc complete; Metro-quarter turn type; Angle valve - Metro- quarter turn type.

Supplying and fixing CP towel rail of size 20mmx600mm long including fixing in position as directed (Metro/Parryware).

Providing and fixing of CP Brass Towel Ring Metro make with CP Brass Screws and etc. complete as per direction of Engineer-in- charge

Supplying and fixing exposed type Toilet paper holder fixing with necessary screws etc complete; Metro.

Supplying and fixing CP Double coat hook fixing with necessary screws etc complete; Metro or parryware.

Providing and fixing of CP Liquid soap container with necessary Screws and etc. complete as per direction of Engineer-in-charge (Metro / Parryware)

Supplying and fixing of Fully Automatic Hand drier of "NOVA-TECH" make fixed near wash basin etc complete.

Providing and fixing of 8mm thick Modi float/ Saint Gobain make Mirror with beweled edges/ edge moulded and fixing the same on wall with SS stud of required number etc.,

Supplying and fixing with new CP brass bib cocks/ angle valve/stop cock / pillar tap/Push cock ( quarter turn/ corn type (metro equivalent)) etc including cost of material, thread, white metal putty etc complete.- (15/20mm dia).

Providing and fixing unplasticised PVC connection pipe brass unions (Kohinoor) 45 cm length 15mm nominal bore

(Schedule C ) Internal Drainage:

Supplying, fixing and testing of 6kg PVC pipes confirming to IS: 4985 and fittings (available fittings in market and fabricated fittings) such as tee, elbow, 'y' , coupler, etc for Soil and Waste pipe works with in toilets etc. Pipes suspended in ceiling, chasing in wall and laid in sunken floor for Urinals and wash basin, floor trap etc. Using solvent cement joints for jointing the pipes with fittings. Work includes chasing in wall, making required size holes in beams, slabs, brick walls etc., and re do same with water proofing components to the entire satisfaction of site engineer etc complete. 40mm dia

Supplying, fixing and testing of 6kg PVC pipes confirming to IS: 4985 and fittings (available fittings in market and fabricated fittings) such as tee, elbow, 'y' , coupler, etc for Soil and Waste pipe works with in toilets etc. Pipes suspended in ceiling, chasing in wall and laid in sunken floor for Urinals and wash basin, floor trap etc. Using solvent cement joints for jointing the pipes with fittings. Work includes chasing in wall, making required size holes in beams, slabs, brick walls etc., and re do same with water proofing components to the entire satisfaction of site engineer etc complete. 50mm dia

Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes / SWR pipe conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion (Finolex/Prince/Supreme). 75mm dia

Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes / SWR pipe conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion (Finolex/Prince/Supreme). 110mm dia

Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes / SWR pipe conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion (Finolex/Prince/Supreme). 160 mm diameter pipe

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 75 x 75 x 75 mm. (Single tee with door)

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 x 110 x 110 mm. (Single tee with door)

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 75 x 75 x 75 mm. (Single tee without door)

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 x 110 x 110 mm. (Single tee without door)

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion. Bend 87.5 degree. 75mm bend.

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion. Bend 87.5 degree. 110mm bend.

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 75mm

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110mm

Cutting holes up to 30x30 cm in walls including making good the same: With common burnt clay F.P.S. (non modular) bricks (For exhaust fan opening)

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc.

Making hole up to 20x20 cm and embedding pipes up to 150 mm diameter in masonry and filling with cement concrete 1:3:6 (1 cement : 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) including disposal of malba.

Providing PCC encasing for all internal pipes with laying cement concrete 1:3:6 mix using 6mm jelly casing all round the pipes etc., complete - 40 to110mm dia.

Supplying and fixing CP Cockroch trap for the size of 125x125mm of Jaguar make including fixing in position etc complete.

Fabricating, supplying, fixing and testing PVC floor trap with 40/50/63/75 dia inlet and 75 dia outlet fixed on the bed of cement concrete etc., complete.

Scheduel D- Water Supply:

Providing and Fixing Chlorinated Polyvinyl Chloride(CPVC) pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including reducers and fixing the clamps at 1 m spacing for open pipe lines. This includes jointing of pipes and fittings (including reducers) with 1 step CPVC solvent cement and the cost of cutting chasses for concealed lines and making good the same including testing of joints complete as per direction of Engineer In-Charge. (Concealed work including cutting chaases and making good the wall etc). 25 mm nominal outer dia pipes

Providing and Fixing Chlorinated Polyvinyl Chloride(CPVC) pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including reducers and fixing the clamps at 1 m spacing for open pipe lines. This includes jointing of pipes and fittings (including reducers) with 1 step CPVC solvent cement and the cost of cutting chasses for concealed lines and making good the same including testing of joints complete as per direction of Engineer In-Charge. (Concealed work including cutting chaases and making good the wall etc). 32 mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall.40 mm nominal outer dia pipes

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore

M/S. NAVEEN CONSTRUCTIONS

ESVEE CONSTRUCTIONS

P Subramani and Co