ADDN / ALTN OF BLDG NO H 20 OFFR WARD (MALE) FOR DINING ROOM AND PROVN OF TWO SHED NEAR BLDG NO H 31 OF MH SHILLONG AND PROVN OF SECURITY WALL ALONGWITH GATE AND SENTRY POST AT MH SHILLONG AND PROVN OF HARD STANDING WITH EXTERIOR TILES AND PROJECTIO

Amount

Dismantling of plain or corrugated steel sheeting any guage thickness including nainital or similar pattern roof covering all as specified.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth and getting out in soft/loose soil, all as specified .

Returning, filling incl spreading levelling watering and well ramming in layers n exc 25 cm thick each layer.

Removing of excavated soil to a distance exc 250m but n exc 500m and deposited where directed n exc 1.5 m above the starting point

M & L PCC 1:4:8 type D2 (using 40 mm graded aggregate) as in Foundation filling and mass concrete complete all as specifed and as directed.

M&L Precast cement concrete block masonry with solid block exc 10 Cm in width with PCC, type C1 (1:3:6) using 20mm graded stone aggregate) and setting in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L Precast cement concrete block masonry with solid block 10 Cm thick with PCC, type C1 (1:3:6, using 20mm graded stone aggregate) (with plain or interlocking joints and setting in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

Demolition of Brickwork or stone/boulder masonry or precast concrete block walling, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework built in cement mortar complete all as specified.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm thickness (below/above ground level) all as directed.

Dismantling of asbestos cement ( Corrugated , semicorrugated etc) sheets in roof covering complete all as specified and as directed.

Dismantling of timber scantling 40 sqcm over in section in any position ( unframed work) complete all as specified and as directed.

All as per item No 11 above but in fillets , rails , posts , Rafts , purlins etc under 40 sqcm in section unframed work complete all as specified and as directed.

Dismantling of wall / ceiling boards ( fiber , pulb , insulation etc) or insulation boards / slab /blankets any thickness including cover fillets complete all as specified and as directed.

Taking down plastering on lathing ( other than wire-netting , without removing lathing in CM on brick walls complete all as specified and as directed.

Taking down Chowkhats or frames with shutters (without taking off shutters from the frame) not exc. 1.5 sq. m each all as specified.

Taking down Chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 sq. m but n exc 4 sq. m each all as specified.

S&F pre-painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick as in roof covering of tensile strength 550 mpa including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour complete all as specified and directed

S&F pre-painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick as in roof covering of tensile strength 550 mpa including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour complete all as specified and directed

Dismantling boarding any description fixed in any position with nails complete all as specifed and as directed.

S&F 20mm thick 2nd class hard wood boarding in eaves board/fascia plained both sides with butt joints fixed with nails complete all as specified.

M&L for Reinforced cement concrete (nominal mix) TypeB0 1:2:4 (12.5mm graded aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) flat complete all as specified.

M & L Granite (of any type) work 20mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. complete all as spefied.

S&F vitreous China clay table top WHB of make Jaguar Cat Part No:-ARS-WHT-39601 of size 635x430x190 mm incl waste coupling Cat Part No:-ALD-727complete all as specifed and as directed. or equivalent in Hindware/Cera/Parryware

S&F Brass CP 2-in-1 Bibcock with flange of complete all as specifed and as directed.make Jaguar Cat Part No:-ORP-10041PM OR equivalent in Marc/Cera/Parryware

S&F fancy type tall body with 155 mm extension body fixed spout without popup waste system with 600 mm long braided hoses of complete all as specifed and as directed.make Jaquar Cat Part No:- KUP-35005BPM or equivalent in Marc/Parryware/Prayag

S&F Soap dish holder of complete all as specifed and as directed.make Jaguar Cat Part No:-AKP-35731P or equivalent in Marc/Parryware/Prayag

S&F Towel ring sqare shape stainless steel of complete all as specifed and as directed. Make Jaguar Cat Part No:-AKP-35721P or equivalent in Marc/Parryware/Prayag

S&F tubular towel rail, chromium plated, 60cm long between flanges, fixed in repairs complete all as specified

S&F harrison rails, aluminium anodised alloy, with fixing brackets, stops, rollars etc complete all as specified and as directed

S& F of brackets decorative for curtain rails complete all as specifed and as directed.

S&F Anodised Aluminium frame work for snapgrid false ceiling comprising of Gl perimeter channnel 0.55 mm thick with Main T- flange of 25 mm and web of 30 mm fixed to surrounding wall angle with flange and web 25 mm each , Cross T with flange 25 mm and web 25 mm fixed to main T, Main T is suspended from soffit @ 1200 mm c/c using GI hangers of 6mm dia GI frame will be 60 x 60 cm to recieve E-board ceiling complete all as specified and as directed .

M&L non asbestos fibre cement building boards of 4mm thick fixed or laid/ inserted to timber/GI/Aluminium framework with screws fixed in ceiling flat or sloping complete all as specified and as specified.

M&L for PCC 1:3:6 type C-2(using 20 mm graded cr. stone aggr),75mm thick as in plinth protection finished even and smooth without using extra cement layed in bays not exc. 2.00m and joints filled with bitumen sand mastic with ratio (1:3 ) complete all as specifed and as directed.

M&L for Rendering 15mm thick on fair faces of concrete surface of wall in CM (1:4) finished even and smooth without using extra cement all as specified and directed

M&L Rendering 10mm thick on concrete surface of wall in CM (1:6) and finished the surface fair & even without using extra cement , complete all as specified and as directed

M&L for preparing surfaces plastered or unplastered, applying two or more coats (over 1 mm thick plaster of paris wall care putty) of 100% premium acrylic emulsion paint having VOC less than 50 gm/ltr and UV resistance as per IS 15489:2004, Alkali & fungal resitance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over new surface on new or previously untreated surfaces all as specified and directed.

M&L for preparing surfaces plastered or unplastered, providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth and Distempering two or more coats with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.

M&L for Aluminium anodized frame Powder Coated (minimum thickness of powder coating 50 micron) for doors , windows , ventilators with one or more rebates incl joing cleat for fixing etc complete all as specified

S&F Anodised aluminium window and ventilator shutters, Powder Coated (minimum thickness of powder coating 50 micron) side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified.

S&F anodised door shutters , Powder Coated (minimum thickness of powder coating 50 micron) aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing , handles 2 nos in each door , hinges , anodised aluminium snap beading screws etc complete all as specified

S&F Sheet glass, 5.5mm thick ordinary quality, in squares,exceeding 0.50 sqm in each pane including rubber packing and aluminium beadingcomplete all as specified and directed

M&L for 12mm thick prelaminated particle board, interior grade prelaminated both side with decorative choice laminations ,fixed with screw etc complete all as specified.

M&L for light shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 complete all as specified and as directed

M&L for light shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick rendering in CM 1:4 complete all as specified and as directed

Taking up or down steel tubing and connections for 15 mm bore of pipes complete all as specified and as directed

Taking up or down steel tubing and connections for 20 mm bore of pipes complete all as specified and as directed

S&F GI steel tubing medium grade 15mm bore with all fitting and fixed complete to wall and ceiling or laid under in floor complete all as specified and as directed

S&F GI tubes, medium grade galvanised, 20mm bore with all fitting and fixed complete to wall and ceilings or laid in floors complete all as specified and as directed

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm,complete all as specified and as directed

S&F Stainless steel kitchen plate rack of size 31" X 30' X 10" made out of stainless steel sheet of 1.00 mm with all accessories including taking down old unservicable rack (Make : Blue star, Cat No - BSKPR-314) complete all as specified and as directed

S&F Angular stop cock, fancy type, chromium plated, 15 mm bore complete all as specified and as directed

S& F 15mm bore stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified

S&F 20mm bore stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed

S&F PVC (SWR) Pipes single socketed in any length with rubber ring joints, 110 mm bore fixed to walls complete as directed

M&L for 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints ,laid in trenches or in floors complete all as specified and as directed

S&F PVC (SWR) bends 110mm dia complete all as specified and as directed

S&F PVC (SWR) bends 75mm dia complete all as specified and as directed

S&F PVC (SWR) 110mm bore bends any radius with access door compelete all as specified and as directed.

S&F PVC (SWR) 75mm bore bends any radius with access door compelete all as specified and as directed.

S&F PVC (SWR) 75mm bore vent cowl compelete all as specified and as directed.

S&F cutting chases, pinning in concrete block workmaking good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades shelves, lintels etc, and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10cm girth complete all as specified and as directed

S&F Stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays ,incl bolts and nuts and securing ends of stays to wall or roof complete all as specified and as directed

M&L for Non Skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colour including Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM (1:6). complete all as specified and directed.

M&L for Glazed ceramic colour tiles in vertical surface of size 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with the tile colour including Screed bed or bedding layer of mortar 10 mm thick for vertical faces in CM (1:4) complete as specified and directed

S&F Factory made solid panel PVC door shutter 30 mm thick (style) considering of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails, lock rail & bottom rails on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed togeather with solvent cement, fixing in the frame at site as per specification & drawing complete all as specified and as directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed

M&L for 4.80 mm thick frosted sheet glass quality and glazing fixed to aluminium frame exc 0.50 sqm complete all as specified and as directed.

S&F PVC valveless, 10 ltrs, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified.

S&F vitreous China clay WHB flat back size 550x400 mm incl pedastal , PVC waste pipe 32 mm dia, waste coupling brackets etc complete all as specified and as directed

S&F Vitreous china wash down water closet pan padestal pattern white, excluding fixing bolts, flushing cistern but including flush pipe, seat and cover complete, fixed in repairs all as specified and as directed.

S & F Brass CP tubular towel rail 20 mm dia , 60 cm long including brackets compelete all as specified and as directed.

S&F Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed all as specified and directed

S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railling 60 cm long screw and cup washer compelete all as specified and as directed.

Supply and fixing rotational moulded HDPE water storage tank ,triple layer ,ISI marked (cylendrical vertical type with closed top) of capacity 500 ltrs in position incl float valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed all as specified and directed.

S&F Concealed stop cock, Chromium plated, 15 mm bore , compelete all as specified and as directed.

S&F PVC connections 15 mm size with PTMT nuts of length 450mm compelete all as specified and as directed.

S&F Bib taps 15mm bore , cast copper alloy fancy type , screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F Grating doom 100 mm dia of PTMT.(Minimum weight 25 gms) compelete all as specified and as directed.

M & L for PCC 1:3:6 C2 (40 mm graded aggregate) as in surface channels and drains all as specified & directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms,moulds,mitred/ stop ends compelete all as specified and as directed.

M&L for 15mm rendering in cement mortar (1:4) in two layers with top 5mm thick mixing with WPC @ 3% by weight of cement over a backing coat of 10mm on brick/concrete surfaces finished the surface even and smooth without using extra cement compelete all as specified and as directed. Note : WPC shall be measured and paid separtely as supply only.

Supply only Integral water proofing compound compelete all as specified and as directed.

M & L for preparation of new walls surface and two coats of white wash over one coat of primer complete all as specified and directed.

S& F Mild steel joist channel or angle or tee section,ms tube and fixed with ms flat iron cut into shape drilled and fixed with screw conforming fe 410 compelete all as specified and as directed.

M&L for PCC ( 1:2:4) type B-2 using 40mm graded stone aggregate as foundation etc. complete all as specified .

M&L PCC, (1:2:4) Type B-0, (12.5mm graded aggregate) 40mm thick as in floor finished even and smooth using extra cement compelete all as specified and as directed.

S & F compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. Fe-290 (Gde E-165) complete all as specified.

S&F plates (plain or chequered ) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment of Fe -410-W( Gde-E-250 quality-A)complete all as specified and as directed.

M&L for preparation of new or previously untreated surface of steel or iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified.

S&F Gun metal gate valve class I (ISI) marked with iron wheel head, screwed both ends for iron pipe, suitable for following bore of pipe including taking down old existing unserviceable gate valve of dia 20 mm complete all as specified and directed by Engr-in-Charge

Excavation in post holes not exc. 0.5 cum, getting out returing, filling in and ramming earth and broken hard core/rubble mixed with earth with around the layers not exiding 25 cm each layers watering and removing surplus soil to a distance not exceeding 50 cm making good complete in soft/loose soil compelete all as specified and as directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates including distance pieces, cleats, plates, welding/rivets/bolts etc complete all as specified.

Surface Excavation n exc 30cm deep and average 15 cm deep getting out in soft/loose soil complete all as specified.

M & L Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface compelete all as specified and as directed.

M&L 100mm thick cement concrete using (40mm graded aggregate) type D-2 (1:4:8) as in sub base compelete all as specified and as directed.

M&L for 25 mm thick cement concrete 1:2:4, Type B-0 (12.5mm graded aggregate) as in floor for tiles all as specified.

M&L for chequered cement concrete tiles 20cm x 20cm x 25/30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry with gray cement and pigment in floors over and including 20mm thick screed bed in cement mortar 1:6 complete all as specified.

Surface dressing n exc 15 cm deep hard/dense soil compelete all as specified and as directed.

M&L for vitrified tiles darkshade (square /rectangular) polished area of each tiles not exc0.36 in floors laid over and incl. 20mm thk 1:6 screed bed jointed pointed with coloured cement to match the tiles compelete all as specified and as directed.

M&L for Reinforced cement concrete (nominal mix) 1:1.5:3 type A1 (20mm graded aggregate) in foundation including rafts, footings, foundation beams, plinth beams, bases for columns etc, basement slabs, and mass concrete etc , all as specified.

M&L for Reinforced cement concrete (nominal mix) 1:1.5:3 type A1 (20mm graded aggregate) in columns, pillars, piers, post and struts , all as specified.

M&L for Reinforced cement concrete (nominal mix) 1:1.5:3 type A1 (20mm graded aggregate) in beams, cantilevers, lintels over 1.5 m span etc., all as specified.

M&L for Use and waste of formwormk to side of concrete foundation, footings, bases of columns, rafts and raft beams, side and soffit of foundation and plinth beams flat, for rough finished surfaces of concrete , all as specified.

M&L for Use and waste of formwork to sides of pillars, columns and stanchions, square or rectngular, for rough finished surfaces of concrete , all as specified.

M&L for Use and waste of formwork to sides and soffit of floor and roof beams, beam haunchings, girders, shelves etc flat for rough finished surfaces of concrete , all as specified.

M&L TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hookings ends and binding mild or securing with clips compelete all as specified and as directed.

M&L mild steel TMT 6mm to 8mm dia as in stirrups cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hookings ends and binding mild or securing with clips as specified.

M & L for PCC 1:2:4 type B1 (Using 20 mm graded aggr) as in coping and similar works incl necessary from work all as specified.

Spreading and levelling in layers n exc.25cm thick , well ramming including watering as required, all as specified.

M&L for Machine cut kota stone slab flooring 18-20mm thick over and incl 20mm thick cement screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for kota stone floor 18-20 mm thick, as in skirting,set and jointed in neat cement slurry and pointed in white or coloured cement to match Complete all as specified.

S & F Mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting etc., and similar work conforming to Fe-290 Gde E-165 complete, all as specified .

S&F Galvanised 2 strand steel barbed wire, 2.24 mm, barbed with 2.00 mm dia barbs at spoacing 75 mm and straining and fixing to any type of strandard rails straining bolts, incl securing or tying at crossing with provn of galvanised mild steel wire, staples or steel pins etc. complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc, complete drilled for fixing of steel sheeting or other covering. Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel, sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete in Fe-290 (Gde E-165) all as specified.

S&F for 2nd class hard wood plain, solid, straight chowkats and frames wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints all as specified and directed.

S&F for 35mm thick, factory made, 2nd class hard wood, Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as spd.

S&F Butt hinges, medium weight, cold rolled mild steel, size of hinges 100mm.

S&F Aluminium alloy, anodised sliding door bolts(250mm long) with hasp,staples( bolt type) and fixing clip of sheet,cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified.

S&F Aluminium handle 150 mm long cast type anodised, complete all as specified.

S&F Aluminium tower bolt (200 mm long), anodised barrel tower bolts of extruded section complete all as specified.

S&F for 30mm thick, factory made, 2nd class hard wood, glazed and skeleton shutter open rebated and prepared to receive glass,gauze etc. without sash bars edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass,etc complete all as specified.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples as in aluminium ventilators,complete all as specified.

S&F Sheet glass, ordinary quality 4.00 mm thk and glazing with oil putty in square not exceeding 0.5 sq m in each pane complete all as spd.

M&L for preparation of new or previously untreated surface of wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified.

AGE E/M SCHEDULE PART - II Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box/metal flush box with suitable modular or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover for housing the switches , socket outlets, fan regulators etc. with brass screws and brass washers and making good the disturbed surfaces as per existing for one light point controlled by one switch. Note :- Switch, socket and fan regulators to be measured and paid for separately . PVC Conduit confirming to IS 9537 part I & III Note (All chases will be cut by chase cutter only) AMke of Cable - KEI/ Havells / Kalinga

Description all as per Srl item No.128 above but for socket outlet point 5 Amp on same board.

Description all as per Srl item No.128 above but for socket outlet point 5 Amp on Independent board.

Description all as per serial item No 128 above but with 4 sqmm cable for 3 pin 15 Amps switch socket outlet (Power point) complete all as specified.

Supply and fixing modular switch 1 way 6 A module 230/250 volt , AC supply, ISI Marked, with white cover plate with frame complete all as specified and directed. Make : Cona , Plaza, Anchor, Vinay

Supply and fixing modular switch 1 way 16 A module 230/250 volt , AC supply, ISI Marked, with white cover plate with frame complete all as specified and directed. Make : Cona , Plaza, Anchor .

Supply and fixing modular sockets 6A 2/3 pin combined 2 module 230/250 Volts, 50 Hz , AC supply, ISI Marked, with cover plate complete all as specified and directed.

Supply and fixing modular sockets 6A/16A 2/3 pin combined 2 module 230/250 Volts, 50 Hz , AC supply, ISI Marked, with white cover plate with frame complete all as specified and directed. ake : Cona , Plaza, Anchor, Vinay

Supply and fixing ceiling rose surface bakelite 65x50mm, 3 terminal complete all as specified. Make : Cona , Plaza, Anchor .

Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type, warm white / white type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete pre wired fixed to wall with 2 nos PVC block of suitable size including taking down old one complete all spcifided and directed.

S & F Exhaust fan 230 volts , 300mm,plastic body including making all electric connection complete all as specified and as directed including cutting of hole on wall and making good disturbed surface of wall and outer wooden box for fan fix on wall including taking down old one Make Bajaj/Havell's/CG.

Supply and fix MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 8 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection, including taking down complete all as specified and directed. Make: Havells Cat part No DHDPSHODRW12 or equivalent in Schnieder/GE/C&S.

Supply and fix MCB DP, 240 Volts, 40 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed including taking down old one.

Supply and fix in repairs MCB, single pole 240 volts 6 to 32 Amps capacity fixed in DB's including taking down old one complete all spcifided and directed.

M & L Sub main wiring with two runs of single core 6 Sqmm FRLSH copper conductor cable PVC insulated, unsheathed, 1100 V including 20 mm dia concealed on wall/ceiling in PVC conduit, medium grade ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall along with one run of 6 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion including taking down old wiring etc complete all as directed. Note: (i) Two runs of 6 sqmm and one run of 6 sqmm cable and one run of PVC conduit shall be measured as one RM. (ii) Cutting of chases in the wall of appropriate size shall be carried out with electric cutter machine . (iii) Necessary plastering in the disturbed surface of wall and distempering /white washing to match the existing colour shall be included in the unit rate quoted.

Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS, 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade, ISI marked, in PVC Casing capping on wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box/metal flush box with suitable steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover for housing the switches , socket outlets, fan regulators etc. with brass screws and brass washers and making good the disturbed surfaces as per existing for one light point controlled by one switch. Note :- Switch, socket and fan regulators to be measured and paid for separately .

Description all as per Srl item No.143 above but for socket outlet point 5 Amp on same board.

Description all as per Srl item No.143 above but for socket outlet point 5 Amp on Independent board.

Description all as per serial item No 143 above but with 4 sqmm cable for 3 pin 15 Amps switch socket outlet (Power point) complete all as specified.

Supply and fix switch piano (ISI marked) Single pole 240 volts, 5Amps all as specified and directed. Make- Havells/anchor/ Legrand.

Supply and fix socket (ISI marked) 2/3 pin and 5 Amps, flush type, 240 volts complete all as specified and as directed. Make- Havells/anchor/ Legrand.

Supply and fix switch socket combination (ISI marked) 2/3 pin and 5/15 Amps, flush type, 240 volts complete all as specified and directed. Make- Havells/anchor/ Legrand.

Supply and fixing LED batten fittings 1x18 Watt complete pre wired fixed to wall with 2 nos PVC block of suitable size including taking down old unserviceable one complete all spcifided and directed.

S & F wall mounted LED batten fittings with all accessories 1X 9 Watt LED / foot light 6000K , extruded polycarbonate, integrated electronic driver and fixed to wall with 2 Nos PVC block suitable size complete all as specified and as directed including taking down old unserviceable light fittings

S & F Exhaust fan 230 volts , 250mm,plastic body including making all electric connection complete all as specified and as directed including cutting of hole on wall and makng good disturbed surface of wall and outer wooden box for fan fix on wall complete all spcifided and directed.

Supply and fixing LED security Building light LED 25 Watt , pressure die cast aluminum housing, heat resistant glass, IP65 protection, better optics for uniform distribtion complete with all accessories internally pre wired and including connecting up with three core 1.5 sqmm flexible copper conductor cable from ceiling rose to connector of light complete all spcifided and directed.

S & F Wall bracket decorative LED with lamp 12 Watt complete with necessary connection including taking down old unserviceable one complete all spcifided and directed.

S & F recesss mounted low glare luminaire 28 Watt PLUTO NEO 2 X 2 complete with all accessories including complete all as specified and directed

M & L Sub main wiring with two run single core 4 Sqmm FRLSH copper conductor cable PVC insulated, unsheathed, 1100 V including Cassing capping ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall alongwith one run of 4 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion inculding taking down old wiring etc complete all as directed.Note: (i) Two runs of 4 sqmm and one run of 4 sqmm cable and one run of PVC cassing / capping shall be measured as one RM.

Supply and fix in repairs MCCB DB 4 way vertical sheet metal enclosure TPN 415 volts, 50 Hz, with IP-43 protection, double door with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting complete all as specified. . (Note : MCB SP/TPN shall be measured and paid seperately under appropriate items of this schedule . Note : Copper thimble shall be used for connection of cable .

Supply and fix MCCB TPN, 240 Volts, 100 Amps, 10 kA rupturing capacity415 Volts complete all as specified and directed including taking down old one.

M & L , installed and testing of Shadow less LED light fittings 40 watt suitable for operation Theatre, ceiling mounted type , two no Domes, colour Temperature 3800-5200K, 220 Volts, 125000 Lux 10 to 15cm depth illumination with specially designed for the healthcare industry with latest technology, extreme effective advance features, excellent laminar flow, 5 memory special function, Spot Diameter- 100-150mm, LED Average Life greater than 5000, Diameter of Light 670 mm, intensity Control 10~100 Digital, shadow less operation light with long life with effective and superior technology suits for Operation Room. with following features: (i) Light colour pattern Adjustment : The panel & remote is designed with graphical icons to allow user to quickly learn and easily operate. (ii) On/off finger touch switch (iii) Light intensity adjustment (iv) Light colour adjustment and including servicing of full light fittings, battery , charger etc. including taking down old one complete all as specified and directed.

Removing excavated material/ surplus soil and depositing where directed at a distence not exceeding 50mtr.at a level not exceeding 1.5 mtr from strting point complete all spcifided and directed.

Supply lay/spread in trenches , river sand ,clean ,including spreading ,levelling ,punning for laying /cushioning of cables all as specified and as directed.

Supply lay in trenches fly ash bricks, old size sub class “B” for cable protection complete all spcifided and directed.

Supply, lay in trenches, floors ,fix on wall/pole, passing through pipes etc.,LT UG cable , 1100 volts grade, PVC/ XLPE insulated , with multistranded aluminium conductors, armoured with galvanised steel wire or tape ,gland, lugs etc , of size 16 Sq.mm 4 core , confirming to IS specifications complete all spcifided and directed.

Material and labour for earthing complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth notless than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers ,galvanised steel and protected by GI pipe 15 mm bore light grade & connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30 cmX 5 cm with 10mm dia TMT bars 8 cm C/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Electrical Plate No 3 of SSR part -I complete all as spcifided and as directed.

Supply and fixing LED lights fitting 1x 10W, 220V,AC decorative box type, warm white / white type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete complete pre wired fixed to wall with 2 nos PVC block of suitable size complete all spcifided and directed.

Supply and fixing LED security Building light LED 35 Watt , pressure die cast aluminum housing, heat resistant glass, IP65 protection, better optics for uniform distribtion complete with all accessories internally pre wired and including connecting up with three core 1.5 sqmm flexible copper conductor cable from ceiling rose to connector of light complete.Make Make:- Bajaj Cat part No- 169821 LED/CG as perr vat No LSTO 25 CDL equivalent model as in Surya / havells .

Supply and fixing Post top 45 watt for gate and landscape lighting with IP 65 Protection n to impact and corrosion, anti glare and uniform distribution complete all as specified and directed by Engr-in-Charge Make- Crompton cat no LPTOI-45-T /Havells / Phlips

Supply, lay in trenches, floors ,fix on wall/pole, passing through pipes etc.,LT UG cable , 1100 volts grade, PVC/ XLPE insulated , with multistranded aluminium conductors, armoured with galvanised steel wire or tape ,gland, lugs etc , of size 10 Sq.mm 2 core , confirming to IS specifications complete all as spcifided and as directed.

Supply and fix on pole / wall or lay in trenches under road / drain crossings etc., for drawing cables, GI pipe light grade , , ISI marked ,of following sizes including necessery pipe , fittings ,clamps, bolts , nuts etc complete all as spcifided and as directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all spcified and directed.

Taking down Sub main wiring of any sizes complete all as spcified and as directed.

Taking down DB including MCB of any sizes complete all as spcified and as directed.

S K Construction