Renovation of Jawhar Rangmanch

Amount

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-InCharge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 30 mm thick

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-InCharge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 30 mm thick

Wooden Paneling

Providing and Fixing of ‘Wooden Slats’ 2430x131 mm with thickness of 16 mm MDF backed with acoustical Fleece providing sound absorption. The perpendicular holes are available on the back of panel which are covered by black acoustical fleece. INSTALLATION ‘Wooden Slats’ can be installed on G.I studs 600x600mm centre to centre 2400mm X 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life with a backing of 50mm thick,1000 GSM Acoustic Wool.

Fabric Paneling

Providing and Fixing of having sizes 600x600/600x1200 mm and thickness of 15 mm with Taper Edge are made with inorganic binder wood fibre, which in all contribute to its wondering features can be installed with PVC H Profile on G.I studs 2400mm X 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength.

Eco Panelling

Providing and Fixing of FR grade gattone 9mm thick eco board panel by using 12mm thick BWR PLY. GI frame work of 48mm GI Studs using 0.5mm thick and stud channels at 610mm x 610mm, 0.5mm thick, fixed with MS angle cleats 1220x610mm centers to wall by using metal fasteners, backed with 24 SWG x 12.5mm GI Chicken Wire Mesh as per detailed drawing. The frame work to be filled with non wooven polyster wedding of 50mm thick of 1000gsm. After that install the 12mm BWR Ply with help of gypsum screw as per requirement. And fixing of Eco Board Panel with help of adhesive. Fire Retardant as per ASTM- E84. The product is light weight, with a density of 218 kg/m3. No odor, Formaldehyde free and a smoke development index of 300 by ASTM –E84. Any Undulations in the Walls to taken care by the Interior Acoustics Contractor for proper packing. - NRC upto-0.9

Extra Height of False Cielling in Hall

Stage Ceiling

Providing and Fixing of Panel having sizes 595x595/595x1195mm and thickness of 12 mm with Taper Edge are made with inorganic binder wood fibre, To be installed on T24 grid system of 0.6mm thick ,Main ‘T’ length minimum 3000mm, web minimum 35mm to be placed at 600mm centre to centre and secondary cross ‘T’ of length 600mm, web minimum 35 mm, inter locked, Wire Support for Main T to be taken at every 1200mm length wise and 600mm width wise,Specially designed for Acoustic.

Carpet all Area

100% Polypropelene Stainsafe carpet having following characteristics : Pattern Loop Graphic, Primary Backing : Woven PP Secondary backing : Dimenstionally stable woven Action back Pile eight/thickness : 6mm(+/-5%), Pile weight : 850gm/sqm (tolerance -5%) not less than 3.5m The carpet shall be of make Carpet to be installed over with 8mm thick PU foam over CC / kota flooring, fixed with approved synthetic adhesive SR-505.

Flooring

Providing & fixing of Stage Wings of fire retardant glazed cotton cloth black fabric as per approved sample.

Providing & fixing of Main frills in double gathering box pleats stiched ut of fire retardant Velvet fabric. The frill to be fixed from the suspension grid with 25mm dia B class ms pipe suitably hung by mean of 35x4mm MS flat. The pipe & flat to be painted with black enamel paint

Providing & fixing of frills in double gathering box pleats stiched out of fire retardant glazed black fabric. The frill to be fixed from the suspension grid with 25mm dia B class ms pipe suitably hung by mean of 35x4mm MS flat. The pipe & flat to be painted with black enamel paint

Providing & fixing of front facia procenium made in MS hollow tubuler section 50 x50 x 2mm and bracings of 40 x 40 x 2 mm and installed at fascia of stage with necessary dash fastners at floor level and rigidly fixed to wall and cladded with 12mm thick BWP ISI make multilayer marine ply with 1.0mm laminate and another side of black paint.

Supply, Installation, Testing & Commission of Main Curtain made out of crepe curtain cloth with horizontal sliding arrangement complete with fixing rails, brakets, sliding arragement & motorised operation complete with runners, master runners, pullies, 3mm steel wire rope, 1 HP motor (cromption) 2 nos. air breaker contractor (L&T/SIEMENS) , 2nos micro switches for auto stop, 3 nos puss buttones for forward, reverse and stop positions. The curtain should be draped to half area when is closed position. Minimum overlap at center should be 900mm and shhould be stitched in double gathering can be operated manually of through remote.

SITC of LED PAR: High Quality Bright LED Par Light with RGBW Colors source, High throw, Event Performance effect lighting, precision color output LED Par light made with die casted aluminum housing . 54 x 3W, 15°/30°/45°/60° RGB LED PAR of IP 20 rating, delivers 4200 Lumens. The fixture should have capability to work on standby mode, via DMX 512 or integrated sound – 2 light program. Power Consumption 180W, Input Voltage AC 100V ~ 240V, 50/60Hz 0 to 100 % smooth dimming, Strobe effect upto 20 Frames per Second (FPS)

SITC of LED cyclorama light Light source : 18PCS 12W 4IN1 LEDs Lens angle : 25º(30º, 45º, 60º optional) Channel mode : 3 / 4 / 6 / 7 / 9DMX channel mode 0-100% linear dimmer Function: color mix, automatic color change, built-in program and strobe effect with adjustable speed Sound controlled via built-in microphone Adjustable sound sensitivity LED Display, easy to control Control : auto, sound active, DMX512, software(connect to computer) Overheating protection Voltage : 100-220V,50/60hz Power : 230W, IP rating : IP20(PLS-18 x 4in 1)

SITC OF 400W LED Blinder Light . 400W LED Blinder Light 30 Degree complete with 3200K/5600K CCT 4x100W Chip On Board LED lamp source, DMX 512 dimming with 4/8 Channel modes, Black finish housing, IP20 protection having Strobe option and smooth dimming, illuminate Stage with uniform light intensity levels

SITC OF LED 150W Profile with Plastic housing (26 degree) Output Lux@2m 11000 Lux ,Lightsource LED Qty 1pcs of 150W LED,Certification Certification CE Working Environment -40?~45? (Operation) -40?~45? (Start up)

SITC OF Gattone Beam 200 ( 10R),Standard DMX512, automatic and master / slave mode,Channel : 16CHs,Focus : Electronical Focus,Dimmer : 0-100% linear adjustment,Pan/Tilt : 540* for Pan, 250* for Tilt.

SITC OF Professional lighting equipment uses the DMX protocol and network for comunication.the DMX Spliter provides one DMX input and six output.

SITC of Digital Lighting Console USB can input the light library DMX512/1990 Standard, total 1024 DMX controlling channels. 4 output interface with optical isolated, withstand 2000 Vrms. Control 240 computer lights, the channel for each computer light can be patch, up to 40 channels. 320× 240 big screen displays all opeation, change and output. Passways are distributed. Knob can be adjusted for different time. X/Y can be control smoothly. The keyboard can be locked independently to avoid incorrect operation. The world famous light libary set internally is convenient to be used. Several fixed internal programs for special effect can provide changeable effect in live.USB memorizer can save the data in live effectively. Green switch power supply installed internally with high performance and the applicable voltage scope of 90V250V is suitable for all the power supply in the world(to be ordered).

SITC of Light Point Wiring from Patch Panel to be Light Point Wiring from Patch Panel to bewith 1.5 Sq.mm 3 Core PVC Insulated and PVC Sheathed Cable including of suitable size forlaying these wires including 16 amps metallic industrial cladsockets with box at top.and FRLS cable

SITC of C clamp for light hanging

SITC of Interconection of signal cable with XLR conector

SITC of DMX Cable, Conductor ( No. / size of wire) 25/0.10 mm Cross-Sectional Area 0.22 sq.mm (24 AWG), Insulation Material HDPE Insulation OD 1.10 mm, Insulation Colours Red / Yellow Shield Conductor ATC Copper – (0.10mm )105 wires (approx) Shield Type Serve Shield – also called Helical, or spiral Jacket Material High Flex Matt Finish PVC Jacket OD 6.00 mm + – 0.10mm, Operating Voltage 300 V Operating Temperature -20⁰ C to +70⁰ C Dielectric Constant 1k hz 2.3

Supply, installation, testing & Comissioning of biamped, coaxial two-way point source loudspeaker with a single 12-15" LF driver and compression driver with 3" or better Voice coil. Frequency Range (-10dB) of 60Hz - 20kHz or better & long term Continuous Power Handling of 300W (Low frequency) and 45W for High Frequency driver or better. The Loudspeaker module shall have a Max. SPL (Peak) of MF/HF>= 131 or better. It should have Horizontal dispersion pattern of 110º or better, vertical dispersion of the loudspeaker shall be 60 degrees or better. The loudspeaker shall be enclosed in a baltic birch plywood enclosure with perforated steel grille.

Supply, installation, testing & Commissioning of Array Frame to suspend Subwoofers offered above. Amm suspension Bracket

Supply, installation, testing & Comissioning of multipurpose subwoofer with a single 15" neodymium LF driver. Frequency Range (-10dB) of 35Hz - 130Hz or better & long term Continuous Power Handling of 500W or better. It should have an axial Sensitivity of > = 90dB (1W/1m) or more delivering a free field Max. Calculated SPL(peak) of >=124db or better. The loudspeaker should have a nominal impedance of 8 ohm or more. The loudspeaker shall be enclosed in a baltic birch plywood enclosure with perforated steel grille. Complete with installation as per the site requirement.

Supply, Installation, testing and commissioning of Active Portable 12 inch loudspeaker system with 2 combo XLR-1/4'' inputs, 3.5 mm input, Bluetooth inputs and 1/4'' TRS line output with 11 hours of play time using the rechargeable lithium ion battery with Freq Response 62Hz - 17kHZ and 109dB peak SPL, 120 H x 50V Nominal coverage.

SITC of single channel with multiple input have mic and bluethooth

16-Channel Premium Mixing Console with 16 Mic Inputs with 48V Phantom Power and HPF per Channel, 24 Line Inputs (16 mono and 4 stereo), 6 AUX Sends + 2 FX Sends, 4 GROUP Buses + ST Bus, 2 Matrix out, 1 Mono out.

Supply, Installation, testing and commissioning of Vocal handheld microphone with Dynamic type of transducer; Polar Pattern: Cardioid / hypercardioid / supercardioid; Frequency response: 50Hz to 15kHz or better; Sensitivity: 1.85mV or better; Nominal Impedance : < 360 or better; ON/OFF Switch.

Supply, Installation, testing and commissioning of wireless handheld microphone with polar pattern:Cardioid / Hypercardioid / Supercardioid; RF Frequency range: 606 MHz to 865 MHz or better; Audio Bandwidth: 80 Hz to 16kHz or better; THD: <0.9% or better; S/N Ratio: >110 dB or better.

Supply, Installation, testing and commissioning of wireless Lapel microphone with polar pattern:Cardioid / Hypercardioid / Supercardioid; RF Frequency range: 606 MHz to 865 MHz or better; Audio Bandwidth: 80 Hz to 16kHz or better; THD: <0.9% or better; S/N Ratio: >110 dB or better.

Supply, Installation, testing and commissioning of gooseneck microphone with table top stand, gooseneck length: 15" or better; Polar pattern: Cardioid / hypercardioid / supercardioid; RFI Sheilding; S/N Ratio: 65 dB or better; Max SPL for 1% THD: 107 dB or better; Frequency response: 50 Hz to 17kHz or better; LED Indication; ON/OFF Switch.

Supplying and fixing 42U floor mount rack (Dimension- DxWxH – 800x600x1866 mm)

Supply and laying of 2 core Sheilded mm PVC Insulated Microphone cable with Ultra low Capacitance 60(Pf/m) ; Outer Jacket : PVC Matt ; Working Temperature :20 °C / +70 °C ; Diametere : 6.5mm ; extremely flexible.

SITC of Connectors & Intercable

SITC of 3 LCD systemAdvanced laser light source is complemented by a newly-developed 0.76-inch LCD panel with incorporated optical compensator. Combined with powerful signal processing technology, this ensures crisp, bright images 9,000 lumens, (1920 x 1200 x 3) pixels Filter cleaning / replacement cycle (Max.)20000 H (service maintenance) Contrast ratio (full white / full black)

SITC of Motorized Screen -HD matte white motorized screen with Remote control aspect ratio 280" Diagonal

SITC of Active phase plate ( HDMI, VGA,AUDIO,CAT 6 etcMPTP-T70-WPT is a 2 gang Decora style wall-mountable HDBaseT transmitter for HDMI or VGA/audio and RS232 at 230ft (70m) transmission with PoC function. It supports Auto-switching or button panel control between the inputs)

SITC of HDMI 2.0 HDBaseT Extender set consist of transmitter and receiver. It extends 1080p HDMI signal via CAT5e/6a cable at 100m/PoC , and enables IR and RS232 pass

SITC of 4K scaler Matrix switcher with 8 video inputs and 8 video outputs, 1 HDMI output with 3 audio de-embedded, IR, RS232.

SITC of Hardware,HDMI Cables, Connectors & interconnection

Repairing of old chair heavyduty . that’s Materials such as cloths, PU foam densityseat 45-50kgs/cumtr, handles, Back side plastic (62 cmX 42 cm)of like a New chair as per direction of engenear incharge.

providing & fixing of SOFA , the seat is made of PU foam with density 28+_2 kg/cum having an additional top layer of super soft PU foam in density 32+_2 kg/cum , upholdstered with fabric or leatherette. Back Foam , The back is made of PU Fan with density 28+_2 kg/cum having with two additional top layer of super soft foam of density 32+_2 kg/cum , upholdstered with fabric or leatherette. . UNDERSTRUCTURE : Understructure is made up of 1.2+_0.1 cm thick hot pressed plywood ( moisture resistence & termite proof as per IS 303)& pinewood of cross section devoid of major knots& surface defects 6 nos per seat & 3.8 mm Dia zigzig spring assembly is mounted over understructure for cushioning purpose 6 nos per seat & 3.8 mm Dia zigzig spring assembly is mounted over understructure for cushioning purpose. LEG ASSEMBLY : it is welded assembly made in Stainless steel ( grade SS 202) tube & plate with plastic end cap.

TWO SEATER SOFA { 60''X29''X32'' ( LXBXH)}

THREE SEATER SOFA { 84''X29''X32'' ( LXBXH)}

Supply and Laying of 2 x 1.5 Sq.mm Fire Survival armoured Cable, 600 / 1000 V rated with annealed Copper conductor having glass mica fire barrier tape covered by an extruded layer of cross linkable ethylene propelene (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

Supply, assembling, errection and Installation of SMC panel water tank of Required Capacity.

HVAC WORK

Air Cooled Type scroll chillers (Fixed speed Multi compressors)

Providing & Fixing of fixed speed multi compressors modular Air Cooled scroll type chillers of Nominal cooling capacity 36 TR to 40 TR( Total Capacity of module should not less then 210 TR and No. of Chillers should be Minimum 6 Nos.) complete with fixed speed multi compressors (Min. 2 per chiller) fully hermetic scroll compressors, 2 fan motor, starter, air-cooled condenser with blue fins, evaporator of Shell & Tube/ BPHE, vibration isolators, inbuilt accumulator, environment friendly refrigerant R-410A, first charge of refrigerant and oil, wiring, all accessories as per specifications, automatic and safety controls, microprocessor control panel, all mounted on steel frame, all accessories as per specifications and any other item required to make the system complete. Make:- Daikin/ York/Trane/ Carrier/Dunham Bush/ Blue Star/ Voltas

Chiller type : Modular air cooled fixed speed scroll, Capacity - 36 to 40 TR Minimum chillers quantity sholud be 9 nos.

These Modular Unit mandatorily should have Master and Slave Arrangments to run in single circuit of 9 Units as one

Machine Should be Modular Only

Maximum Chillers should not be above 16 nos. Including Standby Chiller in One Circuit.

Modular Design to allow connection of multiple machines to make them behave as one unit. And the overall set to continue working in case of break down of one module.

Machine should be Modular type with Emergency Backup operation for Continuous Operation When one circuit fails , other circuit can continue to operate Balanced Compressor Operation

Real-time monitor, adjust and balance the running time of each module and compressor in the system intelligently, which effectively extend the service life of the unit and reduce the frequency of maintenance.

Evaporator type - High efficiency shell and tube type/BPHE

Condenser type - High Efficiency Copper Tubes with Aluminium Blue Coated Fins

Refrigerant - R410A, Min. No. of compressors per chiller - 2 nos. ( No Glide Refrigerant shall be acceptable )

Power Supply: 380-415V/3P~/50Hz

Water Outlet temperature: 7 Deg C

Water Inlet temperature: 12 Deg C

Evaporator Fouling Factor - 0.0001 ( FPS )

Condenser Design Temperature - 35 Deg C

There will not be any other Primary Chilled Water Pump for the system apart from mentioned below quantity to run the chiller operations smoothly.

Minimum COP of complete chiller : Should not be below 3.0 at 100% load 35 Deg C ambient temperature. (Note- COP of the chiller should be inclusive of all the auxillary power consumption like fan power etc )

All the Controller Should have open protocol which should be not be locked out after warranty or during warranty period

Note- All the passwords related to Operation, Service or any other setting in the chiller which required password by OEM. Has to be handed over to purchaser at the time of successful commissioning of equipment.

Please submit the Catalogue mentioning Modular Design with Maximum 16 Nos Chillers in one circuit at the time of TENDER SUBMISSION. - No Deviation Accepted. In case of no catalogue submission then the tender will be rejected.

AIRCOOLED 36 ~ 40 TR CHILLER- (SCROLL COMPRESSOR MODULAR TYPE )

Providing & Fixing of Flow Switches for Chilling Machines including socket welded etc as required.

Providing & Fixing of Remote Controller for Each Chiller Unit - Wired Type ( Wire for remote controller included ) Each Controller Shoule be able to fully operate on individual chiller of 35~40 TR Capacity unit.

There Should be one Master controller to operate all the chillers in one circuit. a. Master Controller should be able to handle Master and Slave Arrangments. b. Should be able to operate, control and monitor each individual chiller in one circuit. Master Controller will be kept in control room. Each Master Controller should be able to handle minimum 16 nos of chiller in one cirucit.

Any Required accessories for the operation of chiller controlling will be in chiller suppliers scope. Please include all the costs related to chiller operation. No additional accessories like Flow Meter, Electrical Device, Sofware & Hardware etc if requrired will be provided by Chiller Supplier.

Providing & Fixing of End suction pumps complete with motor , base frame, vibration isolators and other accessories (except suction and discharge shut off valves, suction strainer, discharge check valves and drain piping which are covered under separate items.) Pumps shall have mechanical seal and Bronze/S.S. Impeller. The pump motor shall be suitable for 415 ± 10%, 50 cycles, 3 phase power supply, squirrel cage induction 2900 RPM TEFC, IE3 motor. (earthing, control wiring and main cable from electrical panel to unit with cable tray with necessary accessories, are covered under separate items) with vibration isolators. Pumps shall be complete as per specifications and shall have operating parameters as given below :

Make : Grundfos/ DP/Xylem/KSB/Armstrong

Primary Chilled Water Pumps

Note - All pumps should be Facotry Fitted only.

Flow rate : 550 USGPM

Head : 15 M, RPM -1450

(1 Working + 1 Standby for Each Circuit)

Secondary Chilled Water Pumps

Note - All pumps should be Facotry Fitted only.

Flow rate : 550 USGPM

Head : 25 M, RPM -1450

(1 Working + 1 Standby for Each Circuit)

Providing and fixing of double skin modular construction, 45 mm thick PUF panels with Thermal break, draw through Floor mounted (FM) Air Handling Units, each complete with mixing box, pre filter (Washable Synthetic fibre of efficiency 90% down to 20 micron), fan section with Centrifugal blower (Make: Nicotra/ Kruger), Squirrel cage, TEFC induction motor (Make: Siemens/ NGEF), cooling coils (Copper tubes and Aluminium fins), V- belt drive arrangement, anti vibration mountings, SS 304, SWG 20, sand witch type drain pan inner ss and outer G. I. powder coated. The RPM of AHU should be less than 900 and blower discharge face velocity should not cross 10 FPS and other accessories all AHU should be single blower. The details of AHU's are as indicated below:

Makes : Zeco/ Edgetech/ Systemair/ Revo/ Flaktwood/ Bryair/ Waves/ Caryaire

Auditorium Sitting Area 11000 CFM / 34 TR - 55mm Static Pressure, 6 Row Deep

Providing and fixing of double skin modular construction, draw through Ceiling Suspended (CS) Air Handling Units, each complete with DIDW Centrifugal fan forward curve blower, Squirrel cage,IE3, TEFC induction motor, cooling coils (Copper tubes and Aluminium fins), pre-filter (Washable Synthetic fibre of efficiency 90% down to 20 micron), Sandwich type drain pan of 20 gauge, SS - 304 inner sheet, 12 mm thick insulation and outer cover should be G. I. with S S drain socket 32mm dia, V belt drive and other accessories as per specifications (except water shut off valves, drain piping and pressure gauges which are covered under separate item). Motor shall be suitable for 415 ± 10% volts, 50 cycle, 3 Phase AC supply. The RPM of AHU should be less than 900 and blower discharge face velocity should not cross 10 FPS and all AHU should be single blower, make of blower is Nikotra/Kruger/ Greenheck . The details of AHU's are as indicated below:

Makes : Zeco/ Edgetech/ Systemair/ Revo/Flaktwood/Bryair/ Waves/Caryaire

Balcony 2nd Floor 4000 CFM / 9 TR - 50mm Static Pressure, 6 Row Deep

Hall 2nd Floor 4000 CFM / 9 TR - 40mm Static Pressure, 4 Row Deep

Balcony 1st Floor 4500 CFM / 8 TR - 50mm Static Pressure, 6 Row Deep

Performance & Rehersal 1st Floor 4000 CFM / 9 TR - 40mm Static Pressure, 4 Row Deep

Hall 1st Floor 4000 CFM / 9 TR - 40mm Static Pressure, 4 Row Deep

Foyer GF 3000 CFM / 7.5 TR - 40mm Static Pressure, 6 Row Deep

Stage 2000 CFM / 5 TR - 30mm Static Pressure, 6 Row Deep

TREATED FRESH AIR UNITS

Supply, Installation, Testing & Commissioning of DOUBLE SKIN type Ceiling suspended type TFA's Comprising of Following : Frame Structure : Extruded profile Aluminium Anodized with thermal break Panels : Double Skin 43±2 mm Thick Mineral wool Insulation shall be injected with minimum 40±2 Kg./M³ density. Pencil coving should be given on the inner frame of AHU's. AHU frame work shall be Anodized Aluminium Section minimum 2 mm thick with thermal break profile & internal coving. Inner Skin : 0.8 mm G.I Plain Galvanized Sheet steel Outlet Skin : 0.8 mm G.I Pre-plasticized / Powder coated Galvanized Sheet steel Skid : MS Epoxy Coated

Drain Pan : 1.2mm Thk SS304 - with 19mm Thk Nitrile Rubber insulation along with 40NB threaded Nipple in SS Construction. 3 way slope to avoid water accumulation in side tray, In case of Coils in two parts the Drain Pan to be made also in two parts ( Upper & lower) with flexible pipe in between them. Sealing Gasket : Food Grade / D profile gaskets of approved MOC Fan Type : Plug Type - Fan shall be as per AMCA standard. TFA shall be supplied with DOL and BMS Compatible Make:- Edgetech/ System air/ Zeco/York/Revo

2500 CFM / 11.5 TR - 50mm Static Pressure

CHILLED WATER BASED CASSETTE

Supply, Installation, Testing and Commissioning of chilled water based cassette type indoor units suitable for two pipe system. These units shall consist of a fan section with dynamically balanced centrifugal fan/s driven by FHP/TEFC squirrel cage induction motor, multirow deep coil of copper tubes and aluminium fins etc. Enclosures shall be fabricated as specified for Dx split units. These units shall be equipped with synthetic fibre filters, insulated drain pan, safety controls, thermostat, a set of valve station with pair of ball valves (one with strainer and one without strainer) and self balancing pressure independent flow control valves etc. all complete in a unit. The unit shall be provided with BMS compatible Kit. Cordless remote-control handset & inbuilt 2 way on/Off type valve PIBCV without thermostat Make:- Edgetech/ System air/ Zeco/York/Daikin/Train/Carrier/Revo

d. 3.0 TR nominal capacity Cassette type unit (chilled water based) with cordless control.

f. 2.0 TR nominal capacity Cassette type unit (chilled water based) with cordless control.

g. 1.5 TR nominal capacity Cassette type unit (chilled water based) with cordless control.

Supply installation, testing & commissioning of Three Way high rangaeability/ pressure independent dynamic balancing cum control valve/Three Way Motorized Valve fitted with motorized, modulating actuators with linear stroke of minimum 15mm, in chilled water lines at each air handling unit, the actuator shall have shut off capability of minimum 4 Bar rating. the actuator shall be controlled by building automation system & should accept a signal of 4-20mA/2-10 VDC. The valve shall be suitable for following flow rates & conforming to specification. The digital electronic controller with LCD display capable of accepting 0-10V DC signal from BMS & Water Temperature signals from the coil inlet & outlet sensors conforming to detailed specifications. all other accessories i.e Sensors-3 No. 230V/24VAC power Supply 1 No. thermowell-1 No. should be included in thsi item.

Make : Danfoss/ Honeywell/ Siemens/Belimo

Providing and fixing of digital thermostats for various Air Handling Units to control PICV valve as per specifications.

Make : Danfoss/ Honeywell/ Siemens/Belimo

Providing & Fixing of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / cu m density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm & below shall be M.S. 'C' class as per IS : 1239.

Makes: Jindal Star/ Jindal Hisar/ TATA

25 MM (19 mm thick Insulation UV Cloth & 2 Layers of UV Paint)

32 MM (19 mm thick Insulation UV Cloth & 2 Layers of UV Paint)

40 MM (19 mm +13 mm thick Insulation UV Cloth & 2 Layers of UV Paint)

50 MM (19 mm +13 mm thick Insulation UV Cloth & 2 Layers of UV Paint)

65 MM (19 mm +13 mm thick Insulation UV Cloth & 2 Layers of UV Paint)

80 MM (19 mm +13 mm thick Insulation UV Cloth & 2 Layers of UV Paint)

100 MM (19 mm +13 mm thick Insulation UV Cloth & 2 Layers of UV Paint)

125 MM (19 mm +13 mm thick Insulation UV Cloth & 2 Layers of UV Paint)

150 MM (19 mm +13 mm thick Insulation UV Cloth & 2 Layers of UV Paint)

200 MM (19 mm +13 mm thick Insulation Aluminium Cladding with Vapour Barrier)

Providing and fixing in position the following Ball valves, flanges, Rubber Gasket, nut bolts, nipples etc as required with insulation.

(Makes: Advance/ Castle/ Keystone/ Honey well/ Sant/ leader/ Zoloto/Kartar/NVR)

Providing and fixing in position the following Butterfly Valves PN16 SG Iron Disc, flanges, Rubber Gasket, nut bolts etc as required with insulation.

(Makes: Advance/ Castle/ Keystone/ Honey well/ Sant/ leader/ Zoloto/Kartar/NVR)

Providing and fixing in position the following Balancing Valves PN 16, flanges, Rubber Gasket, nut bolts etc as required with insulation.

(Makes: Econosto/ Keystone/ Castle/ Sant/ Honeywell/ Leader/Kartar/NVR/LP)

Providing and fixing in position the following Y-strainers PN 16, flanges, Rubber Gasket, nut bolts etc as required with insulation.

(Makes: Aarko/ Sant/ LP/ DS / Leader/ Zoloto/Kartar/NVR)

Providing and fixing in position the following Dual Plate Non Return Valves PN 16 SG Iron Disc, flanges, Rubber Gasket, nut bolts etc as required with insulation.

(Makes: Castle/ Keystone/ Honey well/ Sant/ Leader/ Kartar/ NVR)

Providing and fixing of Water Pressure Gauges of 100 mm dia gauge complete with SS syphon and ball valve alongwith duly welded socket etc as required.

Make: Fiebeg/ H.Guru/ wika

Providing and fixing of Industrial Type Thermometer, with duly welded socket etc as required.

Make: Japsin/ HGuru

Providing and fixing of Auto Air Vent Valves complete with socket, ball valve and nipple welding as required.

(Make: Sant/ RC/ LP/ RB / Honeywell/ Castle/ Zoloto/ Kartar/ NVR)

Providing & fixing in position the ball valves, M.S socket , M.S nipples as required for ceiling suspended A.H.U. coil drain complete with connection to A.H.U. condensed drain line as per the followings-

Make : Zolato/ Sant/ Leader/Castle/ Honeywell/ Kartar/ NVR

15 mm dia

Providing and fixing of expansion tank, fabricated out of 5 mm thick M.S. plate construction, duly insulated as per the specifications and shall be complete with 50mm dia outlets for system connection and overflow, make up connection, drain connection, drain valve, vent connections, valves and fittings as required. Expansion tank shall be complete min 19 mm thick Class O Nitrile insulation covered with Aluminium Cladding.

SIZE : 1000 mm X 1000 mm X 1000 mm (high)

Providing & Fixing of cubical type LT panel suitable for 415V, 3 Phase, 4 Wire 50 Hz Ac supply system having suitable front surface area fabricated in compartmentalized (preferably) design from CRCA sheet steel of 2mm thick for frame work and covers, 3mm thick for gland, plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having Suitable size extensible type TPN aluminium alloy bus bars of high conductivity, DMC / SMC bus bars of high conductivity,

DMC/ SMC bus bar supports, with short circuit withstand capacity of 31 MVA for 1 Sec., bottom base channel of MS section not less than 100mmx 50mm x 5mm thick, fabrication shall be done in transportable sections, entire panel shall have a common copper earth bar of size 25mm x 5mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of Al. bus bars and control wiring with sq. mm. PVC insulated copper conductor S/C cable, cable alleys, cable gland plates in two half, i/c providing following switch gears :- Panel fabricator Make : L&T / Schneider / ABB / Siemens / Legrand

Incoming

800 Amps 4 pole 50KA electrically operated Manually drawout type air circuit breaker with built in short circuit release, over current and earth fault protection with adjustable setting as per specification. (Incoming 3 phase and neutral supply with double loop earthing will be provided by department.) The panel shall complete with following accessories :

3 Phase 96 x 96 sq.mm 0-1250/5 amps CTR digital ammeter 1 Nos

3 nos. 1250/5 amps, 15 VA Class I CT’s.

96 x 96 mm sq. 0-500 Volt digital voltmeter . 1Set

BUS BAR

800 amps 3Phase and neutral Aluminium bus bars with colored heat shrinkable insulating sleeves to suitable size. 1 Set

Outgoing

160 Amp. 25kA, 4 pole MCCB, Icu = 100% Ics with over current, short circuit and approved make complete with rotary handle and spreaders complete as required for Chiller Plants. 6 Set

S/D starter for Primary Chilled water pumps with self illuminated Push buttons for ON & OFF, Ampere meter, MCB, contactors, timer, single phase preventer and O/L relays, suitable for 10 HP Motor. 2 Set

100 Amp. 25kA,4 pole MCCB, Icu = 100% Ics with over current, short circuit and approved make complete with rotary handle and spreaders complete For Secondary Pump Panel 1 Set

SITC of Wall mounting cubical type DOL / Star Delta Starter panel for AHU made out of 1.6 mm thick sheet steel powder coated enclosure designed as per Switchgear OEM type -2 coordination chart and suitable for operation of Blower motor comprising of over load protection relay, short circuit & single phasing protection, ON / OFF push buttons, ammeter, voltmeter, indicating lamps, MCB etc. complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters. Competible with BMS & To be Shut Down on Fire Command

Upto 7.5 HP DOL Starters

Above 7.5 HP Star Delta Starters

Operation & Maintenance of complete Building in all respect i.e, cleaning, maintence,security by providing 2 Nos of Security guard, 1 Nos of Sweeper & 1 electrician & 1 technical person whenever there is booking in rangmanch ( for audio / AC./ lights & all system management ) all the arrangements & staff will work under supervision & direction of Engineer in charge for 3 years

Bidder Name

Amount

Zenith Enterprizes (GSTN-08AFIPM9112Q1ZT) BID ID -2914886

Raj Electricals (GSTN-08AGBPS1419A1ZV) BID ID -2916077

VIJAY CONSTRUCTIONS (GSTN-08ABMPG5459N1ZZ) BID ID -2919034

Aims Buildmart Private Limited(GSTN-NA)--2912821

Kavery Electricals(GSTN-NA)--2915895

Description of Work / Item(s)

Amount

Removing of the existing chairs of Jawahar Rangmach including taking out of useful material and disposal of unuseful material from site. Removed material shall be property of contractor and amount quoted shall be recoverd from contractor running bill.

Zenith Enterprizes

VIJAY CONSTRUCTIONS

Raj Electricals

Aims Buildmart Private Limited

Zenith Enterprizes

VIJAY CONSTRUCTIONS

Kavery Electricals

Aims Buildmart Private Limited

Aims Buildmart Private Limited

Zenith Enterprizes

VIJAY CONSTRUCTIONS

Raj Electricals