REPAIR REPLACEMENT TO JOINERY PVC DOOR KITCHEN CABINETS WORK PLASTERING TILING WORK SANITARY FITTINGS GI AND CPVC TUBING AND REPAIR TO LEAKAGE SEEPAGE ROOFING SHEETS FALSE CEILING WATER PROOFING TO ROOF REPAIR TO CHAJJA AND FACIAS ENDURA TILES PLASTE

Amount

Taking down cement plaster of any description including racking out joints,hacking for key, scrubbing down with water complete all as specified.

M&L for Rendering 15 mm thick in CM (1:6) on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing complete all as specified.

All as above item no 2 but in CM (1:4) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified.

M & L Preparation of new plastered surface of wall including cornices, pilasters etc by brooming down and applying two coats of distemper oil emulsion white or tinted over a coat of alkali resistant primer with hand roller complete all as specified.

M&L Preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer with hand roller complete all as specified.

M&L Preparation of newly plastered surfaces of Wall & applying three coats of white wash complete all as specified.

Demolition of brick masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings,dressed stone work and precast concrete articles complete all as specified.

M&L Brick work with sub class 'B' old size bricks straight or cured on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified.

All as above Item No 08 but except bricks complete all as specified.

Taking down chowkats or frames n. exc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified.

Taking down chowkats or frames exc 1.5 sqm but n exc 4 sqm each with shutters (without taking off shutters from the frame) complete all as specified.

Taking down shutter of any description area exc 1 sqm and n. exe 2 sqm complete all as specified.

S&F for sollid PVC door frame of size 50mmx47mm made out of 5mm plain colour pvc sheeet reinforced with m.s. squre tube complete all as specified.

Supplying & fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing

S&F 35 mm thick 2nd class hardwood factory made plain framed, panelled shutters (any No. of panels) with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces the size of rail & stiles as per IS:1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified.

S&F 35 mm thick 2nd class hardwood factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauge etc.( without sash bars ), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauge etc., sizes of members of shutters as specified in SSR Part I Section 8 clause 8.24 (a) complete all as specified.

Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.) (Area not exceeding 2.00 sqm each) complete all as specified and as directed) complete all as specified.

M&L for rolled mild steel framed work such as grill grating etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors , laddres, door gate frame, framed baliusters, walk ways, railing , frame work of water tank and similar work conforming to Fe-290, Gde-E-165 complete all as specified.

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde E-165 including necessary welding etc. and fixed in position. complete all as specified.

S&F 100 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to chowkats Complete all as specified.

S&F 150 mm long mild steel barrel tower bolts stove enameled black with bright bolt (ISI marked) Complete all as specified.

Mild steel pressed steel bow handle oval type stove enameled black of size 150 mm (ISI marked) Complete all as specified.

S&F MS sliding door bolt, plate type, 300mm long, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts & nuts, 4 on bolt plate and 2 on staple plate and fixed. Complete all as specified.

S&F extruded aluminium alloy handle 150mm size fabricated type anodised, ISI marked complete all as specified.

S&F Aluminium anodised barrel tower bolt 150mm long of extruded section and fixed complete all as specified.

S&F 75 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to Complete all as specified.

S&F for Factory made steel window with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded complete all as specified.

All as per item No 28 above but without glazing bars.

M&L dismantling floor,hearth or wall tiling including cement mortar bedding (but not backing) , removing serviceable tiles to store and rubbish off the premises complete all as specified.

M&L colored Glazed ceramic Tiles,in verticle surface 450X300X7mm set & jointed in neat cement slurry and pointed in white or colour cement to match the existing surface over and including 10mm thick rendering in CM 1:4 complete all as specified.

M&L for Coloured Non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, set and jointed in neat cement slurry and pointed in coloured cement over & including 10mm thick screed bed in CM 1:4. complete all as specified.

M&L for coloured Glazed ceramic tiles in vertical surfaces of size 300mm x 200mm, 7mm thick , set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface over and including 10mm thick rendering in CM 1:4 complete all as specified.

Demolition of cement concrete unreinforced in ground floor and paving n.exc 15 CM thickness (below or above GL) complete all as specified.

M&L Non - skid Ceramic colored tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors over 10 mm thick screed bed in CM 1:4 in floors set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified.

M&L for plain cement concrete 1:3:6 type C-1 using (20 mm graded stone aggregate) as in sub base of flooring complete all as specified.

Dismantling of stone slab and tiles of any description or thickness in floors, etc. laid dry or laid dry and pointed complete all as specified.

M&L for Machine cut kota stone slab flooring 20-25 mm thick over & including cement screed 20 mm thick in cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for Machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over & including 10mm mm thick rendering in cement mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

Providing and fixing 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified.

Cutting, polishing existing Kota/ marble floor flooring,& verticle surfaces (three cuttings and mirror polishing) levelling certain places to Kota/ marble floor ,necessary repair work & all necessary arrangments complete all as specified.

S&F 3 mm thick plain sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane including hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads complete all as specified.

M&L for Sheet glass ordinary quality 3 mm thick and glazing with oil putty in square n. exc 0.50 sqm in each pane complete all as specified.

M&L for Sheet glass ordinary quality 5.5 mm thick and glazing with oil putty in square n. exc 0.50 sqm in each pane complete all as specified.

S&F Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified.

S&F in repair bib tap, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of 15 mm bore, complete all as specified.

S&F in repair brass ball valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed of 20mm bore, complete all as specified.

S&F in repair of pillar tap, cast copper alloy with capstan heads,chromium plated, fancy type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore complete all as specified.

M&L 100 mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base/ sub floor complete all as specified.

M&L for Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade (compacted) Over and including sand cushioning 25mm thick complete all as specified.

Dismantling Asbestos cement ( corrugated and semi corrugated) sheets in roof coverings complete all as specified.

M & L Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified.

M&L for preparation of new untreated steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

M & L prepration of new wood or wood based surface of any description over 10 cm widtgh or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

S&F of 500 ltr ISI marked three layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position & including 20mm brass ball valve Including dismantling of existing water tank of 500 Ltr capacity complete all as specified in SSR Part-I.

Demolition of PCC in roof covering, kerbs, roof kerbs, benching, coved fillets etc including old decayed water proofing treatment of any type all as specified (including disposal of building rubbish/ of dismantled or waste material collected after demolition of existing treatment & dumping for lead upto 1km for all lifts)

M&L for 40mm thick PCC 1:2:4 type B-1(using 20mm graded stone aggregate) in roof covering , benching , etc & finished even and fair complete all as specified.

M&L for screed bed or bedding layer of 15 mm thick cement mortar 1:4, for floor finished even & smooth without using extra cement complete all as specified (mixed with WPC) Note :- WPC Shall be measured and paid seprately.

Supply only water proofing compound ISI marked complete all as specified.

S&F APP based polymeric membrane not less than 3mm thick, weighing not less than 3.5 Kg/sqm , reinforced with polyster non-woven fabric (weighing not less than 150 gm/sqm and upper side of membrane thermally insulated with white mineral gravel finish, informaly embadded during manufacturing process shall only be used. It shall be laid by torch application,side overlaps shall be 75mm and the ends shall be 100mm and all over laps shall be sealed by torch application including applying a coat of cold applied bitumen primer conforming IS:[email protected]/sqm & applied a Hot blown coat of bitumen layer spread over primer @ 1.0 Kg/Sqm

M&L for PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified.

S&F for in repair Brass Chromium plated long body Bib cock with wall flange complete all specified. (Make;- ESSCO cat part no APR 105107 or equivalent in Jaquar, parryware)

S&F for in repair Brass Chromium plated Angular stop cock with wall flange complete all specified. (Make;- ESSCO cat part no APR 101053 or equivalent in Jaquar, parryware)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete all as specified.

(a) 25 mm bore

(b) 20 mm bore

S&F in repair viterous china Table Top Basin with CP waste coupling, Size: 500x420x120mm complete all as specified (Make;- Jaquar Registered design FLS-WHT-5935 or equivalent in Hindware ,perryware

S&F in repair for PVC wall panelling in repair with panel of 300 mm x 6 mm Hollow section of Sintex pattern SPUF- 146 or equivalent , fixed with PVC plug and screw and inserted to next panel groove, edges and corners of all door/ window/openings etc to be covered with PVC angel fixed with solvent cement complete all as specified as manufacturer's Instructions.

Repair to aluminium door & window shutters alongwith necessary fittings and fixtures such as hinges ,rubber, washer ,rubber seal ,aluminium beadings ,door lock,handle etc all as specified.

S&F 5.5 mm thick plain sheet glass ordinary quality and glazing with oil putty in square exceeding 0.5 in each pane including hacking out old broken glass (any thickness, size, quality or description) from wooden frames ,alum frame or stone, concrete or brick surrounds glazed with putty or fixed with beads complete all as specified.

S &F in repair 18mm thick solid PVC ply of first quality of one side prelaminated of approved colour and one side white colour fixed with screw 'solvent cement/adhesive for cupboard shutter complete all as specified.

S & Fin repair 18mm thick solid PVC ply of first quality of both side white colour fixed with screw 'solvent cement/adhesive for shelves, partitions and drawers etc for kitchen cabinet and cupboards complete all as specified.

S & F stainless steel handle of 110mm size of best quality as per approved sample complete all as specified.

S & F magnet catch for kitchen cabinet shutter as per approved sample complete all as specified.

S & F colour powder coated mild steel continuous (piano) hinge, width of flaps(when open) is 30mm complete all as specified.

S&F in repair Single piece-WC with UF Soft Close Slim Seat Cover, Fixing Accessories, Accessories set and Cistern Fittings, Size: 370x670x720 mm, S Trap-220mm complete all as specifies (Make;- Jaquar Registered design LYS-WHT-38851S220UFSMN or equivalent in Hindware ,perryware)

Providing and fixing in white vitreous china Large ISI Urinal SIze of 382x398x601 mm (Make Kerovit Catologue No :Rasso (isi) Model No-KS507 in Perryware ,Hindware equivalent )and sizes respectively with with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required complete all as specified.

Supply and fixing in repair anodized snap grid frame work of size 605mm x 605 mm for false ceiling including necessary notching. The snap grid shall consist of anodized aluminium main & cross tee of size 36.5 x 25 x 1.4 mm weighing 0.24 Kg/RM and 23.5 x 26.4 x 1.40 mm weighing 0.191 Kg/RM respectively. The main and cross tee shall be jointed at junction crossing with anodized aluminum angle bracket of size 15mm x 15mm x 1.5 mm weighing 0.12 Kg/RM fixed with suitable MS bolts, nuts and washer. The snap grid (main/cross tee section) shall be supported at ends all along the wall with anodized aluminum angle of size 40 x 25 x 2 mm weighing 0.36 Kg/RM fixed to wall with suitable arrangement and providing 12 mm thick mineral fibre board of approved make fixed in grid support with 6.0 mm dia plain mild steel wire galvanised class 3 fixed in detached works etc to support snap grid, made of aluminum as per specification complete all as specified.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) as in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified.

M&L for fixing of sunroof stone (of approved quality) of thikness 40mm, wherever required as per approved design, including inserting/fixing of stone up to 9m height.Complete all as specified. Note :- Quoted rates includes cost of material , ,safety measures/ use of specified equipments for workers required to complete the work & including all leads.

M&L for plain cement concrete 1:4:8 type D2 (40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified.

M & L for Endura Designer Collection Series of Jhonson Tiles ,Kajaria or somani tile of size 300x300x10 mm having with water absorption less than 0.5% in all colours and shades for outdoor floors such as footpath, court yard, multi modals location etc., laid on 15mm thick base of cement mortar 1:4 in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc, complete all as specified.

M&L for Vitrified Light Shade ceramic tiles 10 mm thick (Square/rectangular) area of each tile not exceeding 0.36 sqm , over & including 15 mm thick screed bed in CM 1:4 in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified.

S&F Rolled sections as in as in post ,roof trusses (framed), trussed, purlins, crane gantries, rails , fastenings , heavy bracket framing (Beam, tee, angle, channel or flat sections,ms pipe) including distance pieces, cleats etc. conforming to Fe-410W Gde E-250 quality 'A' including cutting,welding etc complete all as specified.

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft/ loose soil complete all as specified.

M&L of PCC 1:3:6 type C-2 (using 40 mm graded stone aggregates ) as in foundations filling and mass concrete complete all as specified.

M & L for Pre- painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in ridge , fixed with self tapping screws complete all as specified.

S&F of three layred 1000 ltr ISI marked rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 20mm brass ball valve Including dismantling of existing water tank of 1000 Ltr capacityl complete all as specified in SSR Part-I.

S & F powder coated Anodised Aluminium frame for door,windows,vantilators with one or more rebates including joining cleats for fixing etc complete all as specified.

S & F powder coated Aluminium door shutter,aluminium section weighing 0.55kg/m including necessary joining cleats glazing clips,rubber neoprene packing handles 2 Nos in each door,hinges 100mm long-03 Nos in each shutter anodized aluminium snap beading screw etc complete all as specified complete all as specified.

S&F powder coated Anodised aluminium window and ventilators shutters,side hung type without sash bars,aluminium section weighting 0.55 kg/m including necessary joining cleats,glazing clips,rubber packng,anodised aluminium snap beading,screws,anodised aluminium fitting such as peg stays 150mm long 1 nos ,hinges type B-21 100 mm long 02 Nos suitable handle01 Nos in each shutter complete all as specified complete all as specified.

M&L for providing and fixing 4mm thick Aluminium Composite Panel (ACP) Sheet for partition,door of approved make,color & shade.Joint of sheet to be finished with selecon based sealent also including all fittings & fixtures complete all as specified.

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box,main body with stainless steel cover,governing pivot made of brass,other parts made of mild steel heavy duty and fixed complete all as specified.

S&F in repair Aluminium extruded section body door closer hydraulically regulated designation no 3 universal type suitable for door shutter up to 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation, boards/slabs/blankets, any thickness, including cover fillets and frame work complete all as specified.

S&F 4mm thick non asbestob fibre cement building boards fixed or laid/inserted to timber/GI/Aluminium ceiling frame work with screws complete all as specified.

S&F anodised aluminium snap grid frame work of size 605x605mm for false ceiling complete all as specified.

S&F hangers 6mm dia. G.I (up to 1200 mm length ) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40x3mm size 60 mm long and hold fasterners 12.5mm dia 40mm long.complete all as specified.

M/s Ranaji Construction Co (BID ID -3330007)

abhinav and company (BID ID -3332244)