Waste to Wealth Park at Nakoda Colony in Municipal Area Baran.

Construction of embankment with approved material obtained from borrow pit with all lifts and leads, transporting to site, spreading, grading to required slope and compacting by vibratory roller 8-10 tonne to meet requirement of table 300-2 including cost of compensation for earth taken from private land complete as per MoRT&H specification clause 305. (Lead taken upto 5 km)

Making lawns including ploughing and breaking of clod, removal of rubbish, dressing and supplying doobs grass roots and planting at 15 cm apart, including supplying and spreading of farm yard manure at rate of 0.18 cum per 100 sqm.

Earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal of surplus excavated material at a lead upto 50m suitable site as per direction of Engineer for following depths, below natural ground / Road top level. In all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc. Depth upto 1.5 m

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level : 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Brick work with FPS bricks of class designation 75 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level : 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Supply and erection of Galvanized Iron pole with galvanizing done in single dipping (Average coating thickness Minimum 65 Microns) continuously tapered poles having Octagonal / Circular cross sections designed to withstand the maximum wind speed as per IS 875, The pole shaft shall be made from sheet steel (HT Steel Conforming to grade S355JO) and confirming to BSEN 10025 and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding. The welding of pole shaft shall be done by Submerged Arc Welding (SAW) process. pole shafts shall be provided with the rigid flange plate of suitable thickness (Fe 410 conforming to IS 226 / IS 2062) with provision for fixing 4 no. foundation bolts, This base plate shall be fillet welded to the pole shaft at two locations i.e. from inside and outside.The octagonal Poles shall have lockable door of approximate 500 mm length at the elevation of 500 mm from the Base plate with bakelite sheet having 6A SP MCB and 16 sqmm stud type connector ( 4 nos) inside the pole at door opening for cable connection of following length and dimension as per table P-01 with base plate and foundation bolt on the Existing cement concrete foundation.All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . Poles with Octagonal Cross Section 3 Mtr.

Providing & Fixing of IK08 IP65 protected Top/Bottom mounted LED Post top Luminarie made of single piece construction powder coated die cast alluminium housing with UV stabalized Clear / frosted Polycarbonate diffuser and Aluminium anodised with sand blast reflector. The System level Luminous efficacy ≥ 100 Lumen/W. SMD LEDs is to be used, System CRI>70, CCT: 3000/4000/6500 K. The integral electronic driver must be potted & has a unique BIS R number must be potted & has a unique BIS R number constant current and Internal/external surge protection device of min. 4KV(L-N) and efficiency > 85%, PF>0.9, THD<10% and input Voltage range of 140-270V AC at 50Hz. System life of 50000 Burning hours with 70% of Initial Lumens maintained . Driver current <750mA. Fixture must be in compliance with BIS Standards and Trade mark Certificate complete in all respect.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . Minimum lumen output 2500 lm Post top Luminarie

Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray (with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 6.0 Sq. mm 2 core

Providing & Fixing of Recessed/surface mounting heavy duty horizontal type Double Door ( Metal / Glazed )Distribution board with Metal end box made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3, powder painted complete with reversible door (for double door DB only )100 amp. insulated copper bus bar/shorting link , copper neutral link, copper earth link , color coded interconnecting wire set of suitable rating and din bar,masking sheet, making internal DB terminations with copper lugs, Ferrules, detachable gland plate, including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in-charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR Metal door (single phase) IK-09 and IP-43 with Metal end box 6 Way (6+2)

Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in-charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR Single pole MCB (With B/C curve tripping Characteristics) 40 A rating

Providing weep holes in brick/ stone masonry/ Plain/ Reinforced concrete abutment, wing wall/ return wall with following dia AC pipe, extending through the full width of the structure with slope of 1V : 20H towards drawing face complete as per drawing, technical specifications and clause 2205 of MoRT&H Specification including all scaffolding, material, labour, machinery etc. 150 mm dia

Item Rate BoQ

BoQ_Ver3.0

Bidder Name :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

Construction of Jogging Track using clay Mix approx 65% Clay , 25-30% Stone dust , 5-10% and including grinding of clay and mixing by mechanically means Preparation of bed, laying clay mix manually and compacting using hand roller marking surface leveled and even, Including cost of water hire charges of all T&P complete in all respect as directed by Engineer in charge

Fabrication, Supply, and Installation of Gabion Artwork forming the letters “I❤BMC”, constructed using scrap iron rods and mesh structure, with infill of C&D waste pebbles or stone aggregates, including the following technical components and works: • Overall height of 3 to 4 feet and width of approximately 3 feet per letter, with a combined structure weight of around 600 kg. • Frame made of MS rods (Ø8–12 mm) and MS angle 35x35x5 mm, fabricated into gabion-type wire mesh boxes forming the letter contours. • Internal filling with C&D waste pebbles or similar size stones (40–80 mm) compactly placed to ensure structural stability and visual consistency. • Base support work including PCC (1:2:4) or RCC base slab (M20 grade) depending on site condition, ensuring level and load-bearing surface. • Complete fixing and installation at site, including alignment, welding, and anchoring to base using suitable foundation bolts. • Anti-corrosive coating (red oxide primer and enamel paint) on all exposed metal members for rust protection. • Work includes all materials, labour, tools, and equipment required for fabrication, transportation, and installation as per standard engineering practices.

Fabrication, Supply, and Installation of “Map of India” Sculpture made entirely from scrap metal and recycled components, having an overall dimension of approximately 9 ft × 7 ft, including the following technical works and specifications: • Framework structure fabricated using MS angles 40x40x5 mm and round bars Ø10–20 mm, providing stability and maintaining the outline of the map. • Surface created using MS scrap sheets, metal pieces, and other waste metal components, welded and ground to form a continuous artistic texture. • All weld joints made continuous, ground smooth, and finished for uniform appearance and safety. • Application of anti-rust red oxide primer followed by weather-resistant metallic enamel paint on the entire surface for corrosion resistance. • Foundation and base work including earth excavation up to 1.5 ft, RCC base (M20 grade), and MS base plate (10 mm thick) anchored using M16 foundation bolts for permanent stability. • Installation and alignment at site with all required labour, materials, tools, and safety measures as per standard fabrication and installation practice.

Fabrication, Supply, and Placement of Tyre-Waste Sofa & Table Set, made entirely from recycled vehicle tyres and scrap materials, comprising 4 single-seater sofas and 1 round table, including the following technical components and works: • Sofa frame made using used vehicle tyres (nylon/radial type) stacked and bolted with MS flat bars (40x6 mm) and MS round rods Ø10 mm for stability. • Table top formed using cut tyres and metal base frame, with MS circular ring (Ø25 mm rod) and MS sheet top (3 mm thick) for rigidity. • All joints fixed using arc welding and mechanical fasteners as required for structural strength. • Surface cleaning, buffing, and coating with black weather-resistant rubber paint for a uniform and durable finish. • Cushion seating (if included) to be fabricated using PU foam with rexine cover fitted over a plywood base (12 mm thick). • Includes complete fabrication, finishing, and delivery at site, with all necessary labour, materials, tools, and handling charges.

Fabrication, Supply, and Installation of Colour Palette Artwork with Paint Brush, made entirely from scrap metal components, having an approximate height of 2–3 feet and width of 7–9 feet, with an overall weight of 300–400 kg, including the following works: • Framework fabrication using MS angles 35x35x5 mm and MS round bars Ø10–16 mm, providing structural rigidity and contour for the palette and attached brush. • Outer body and detailing made from MS scrap plates (3–5 mm thick) and recycled metal parts, fully welded and ground for smooth finish. • Paint brush element integrated as part of the structure, made of scrap rods, sheet metal, and pipe sections to replicate form and scale proportionate to the palette. • Anti-rust treatment with red oxide primer followed by weather-resistant enamel paint applied over the complete structure for corrosion protection. • Foundation work comprising earth excavation up to 1.5 ft, PCC (1:2:4) base, and MS base plate (10 mm thick)anchored with M16 foundation bolts for stability and secure installation. • Includes complete fabrication, transportation, erection, alignment, and finishing with all materials, labour, and tools as per standard engineering practices.

Fabrication, Supply, and Installation of Bouquet-Shaped Curved Sculpture with Integrated Lighting, made entirely from scrap metal and recycled components, having an approximate height of 10–12 ft, including the following technical works: • Structural framework fabricated using MS angles (40x40x5 mm), MS round bars (Ø12–20 mm), and scrap metal sheets (3–5 mm thick) to form the curved bouquet structure. • Surface elements made from scrap metal pieces, welded and ground to form smooth contours and details of the bouquet. • Integrated lighting system mounted on the sculpture, including LED fixtures, metal holders, and concealed wiring, with all electrical connections following standard safety practices (non-functional load-bearing). • Anti-corrosion treatment with red oxide primer followed by weather-resistant metallic enamel paint over the entire sculpture. • Foundation work including earth excavation up to 2 ft, PCC (1:2:4) or RCC base (M20 grade), and MS base plate (10 mm thick) anchored with M16 foundation bolts for permanent fixing. • Includes complete fabrication, transportation, site erection, alignment, finishing, and installation of lighting, with all materials, labour, tools, and equipment as per standard engineering and safety practices.

Recycled plastic peacock for show piece With support of MS frame ISI marked. Frame of MS and covering it by lumbers made by MLP waste plastic , also screwed by SS screws. Peacock in front made by metal frame internally for support and outside recycled plastic sheets. Made by recycled plastic sheets termite proof , water proof , fire retardant and anti thef Each lumbers size-: L-4ft, B-6 inch. Thickness of recycled plastic sheets-: 8mm and 18MM used. In front flower pots size of 6 inches and big pot size of L-2ft. B-1ft. Size can be variable as per officer in charge on site. Also coloured as per requirement.

Fabrication, Supply, and Installation of Metal Cube Sculpture, made entirely from scrap metal and recycled components, with overall dimensions of 5 ft × 5 ft × 5 ft, including the following technical works: • Structural framework fabricated using MS angles (40x40x5 mm) and MS round bars (Ø12–16 mm) to form the cube skeleton.