REPAIRS TO KITCHEN TILING, JOINERY, PLUMBING AND MISC B/R WORK AT JCOs, ORs MD ACCN IN ZONE D AND REPAIR AND MAINT OF VARIOUS SHEDS, SHUTTER, GATE AND MISC WORK IN AOR OF AGE BR II UNDER GE DINJAN

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness. (below or above ground level) complete all as specified and directed.

M&L for plain cement concrete (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and as directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks (old size brick), straight or curved on plan exceeding 6 m mean radius, built in cement mortar (1:6) complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius, built in cement mortar (1:4) as in half brick thick walls complete all as specified and as directed.

Dismantling of frame work, timber scantlings 40 Sq.cm and over in section, in any position complete all as specified and as directed.

Taking down chowkats or frame with shutters (without taking off shutter from the frame) not exceeding 1.5 Sqm in each complete all as specified and as directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) exceeding 1.5 Sqm but not exceeding 4 Sqm in each complete all as specified and as directed.

Taking down shutters of any description and refixing in same location/opening not exceeding 1 sqm each including resecuring or easing & adjusting also refixing existing serviceable builders hardware complete all as specified and as directed.

Taking down shutters of any description and refixing in same location/opening exceeding 1 sqm but not exceeding 2sqm each including resecuring or easing & adjusting also refixing existing serviceable builders hardware complete all as specified and as directed.

S&F for second class hard wood plain, solid, straight chowkat and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S&F pressed steel frames for doors of size 105x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including providing and fixing necessary lugs, 100mm butt hinges, lock strike plate, shock absorber etc and including PCC filling of hollow section using plain cement concrete (1:3:6) type C1 complete all as specified and as directed.

S&F pressed steel frames for doors of size 125x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including providing and fixing necessary lugs, 100mm butt hinges, lock strike plate, shock absorber etc and including PCC filling of hollow section using plain cement concrete (1:3:6) type C1 complete all as specified and as directed.

S&F for 35 mm thick, second class hard wood, glazed and skeleton shutters with open rebated and prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut mitered beads for securing glass, etc, sizes of members of shutters as specified in SSR Part I, Section -8, clause 8.24 (a) complete all as specified and as directed..

S&F for 35 mm thick, second class hardwood, Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and as directed.

S&F 30 mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc, divided in to squares, with plain, chamfered or rounded, mitered and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded as in SSR Part I Section 8 clause 8.24 (b) complete all as specified and as directed..

S&F for solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, complete all as specified and as directed.

S&F for 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F for 75 mm size stainless steel, butt hinges, medium weight, cold rolled, complete all as specified and as directed.

S&F for 150 mm size aluminium handles, cast type, anodised complete all as specified and as directed.

S&F for 100 mm size aluminium handles, cast type, anodised complete all as specified and as directed.

S&F for 150mm long aluminium, barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and as directed.

S&F for 100mm long aluminium, barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and as directed.

S&F for aluminium sliding door bolts, 250mm long, plate type, stove enamelled black, with bright bolts not less than 12mm dia with & including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate etc complete all as specified and as directed.

M&L for mild steel framed work such as grills, gratings, gates etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bar, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 (Gde E-165) complete all as specified and directed.

S&F for mild steel small articles using flat iron of size 25x3mm thick such as band, strap, hold fast, cleat, support, hook, hinges, base tie for door frame etc and other similar items conforming to Fe-290 (Gde E-165) complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C-1 (using 20 mm graded stone aggregate) for fixing hold fast complete all as specified and as directed.

S&F in repair steel windows with side double hung shutters including projecting /box type hinges with steel handle, and steel peg stay complete with glazing bars, devotailed or welded complete all as specified and as directed.

S&F in repair steel windows with side double hung shutters including projecting /box type hinges with steel handles and steel peg stay complete without glazing bars, dovetailed or welded complete all as specified and as directed.

S&F in repair steel ventilators with top hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel complete all as specified and as directed.

S&F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified complete all as specified and as directed.

S&F anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F for galvanised mild steel wire cloth of 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F in repairs galvanised mild steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or steel frames, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed.

S&F for 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F for 4.8 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F for 12mm thick prelaminated particle board, interior grade, both side with decorative choice lamination fixed with screws to timber frame works as in shutter of cup board and other similar work complete all as specified and as directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, in roof covering including ridges complete all as specified and as directed.

S&F for 0.80 mm thick, galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with L-type or J-type or cranked hook bolts and washers, in roofs, with grade of zinc coating 275, conforming to IS -277-2003 complete all as specified and as directed.

Fixing only 0.80 mm thick, galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with L-type or J-type or cranked hook bolts and washers, in roofs, with grade of zinc coating 275, conforming to IS -277-2003 complete all as specified and as directed.

S&F for 0.80 mm thick, galvanised, plain mild steel sheet as in ridge, hips, valley gutters and flushings, fixed with L-type or J-type or cranked hook bolts and washers, with grade of zinc coating 275, conforming to IS -277-2003 complete all as specified and as directed..

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of profile as approved, any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F for pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/valley gutter, fixed with self tapping screws complete all as specified and as directed. Note : Colour of ridge shall be same colour as that of sheet used for roof.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc.) any thickness including cover fillets and frame work any type complete all as specified and as directed.

S&F for GI snap grid frame work of size 605mm x 605mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos E-board (plain), HSPC fixed to frame complete all as specified and as directed. Make of E-Board : Eternit Everest / Lafarge/ Armstrong/Visaka Industries Ltd.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposing the rubbish off the premises complete all as specified and as directed.

M&L for 75 mm thick, plain cement concrete (1:3:6) type C-1 (using 20mm graded stone aggregate) as in plinth protection, footpath, etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand (1:2) making impressions of expanded metal whilst the concrete is green complete all as specified and as directed.

M&L for 75 mm thick plain cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base of floor, etc complete all as specified and as directed.

M&L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. including 15 mm thick screed bed in cement mortar (1:6) and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and as directed.

M&L for glazed, ceramic, coloured tiles of size 450mm x 300mm x 7-8mm thick, on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 10 mm thick backing of cement mortar (1:4) complete all as specified and as directed.

M&L for chequered cement concrete tiles of size 20cmx20cmx25mm thick, as in floors etc, including 20 mm thick screed bed or bedding in cement mortar (1:4) and set and jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and as directed.

M&L for granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.

M&L for machine pressed precast conctete interlocking paver block, design & shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment including 75 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and as directed

M&L for rendering 15 mm thick in cement mortar (1:6) on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10 mm thick in cement mortar (1:4) on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 5 mm thick on ceiling in cement mortar (1:3) finished even & smooth without using extra cement complete all as specified and directed

M&L for preparation of new untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and as directed.

M&L for preparation of new plastered surfaces and applying three coats of white wash of ceiling/ false ceiling etc complete all as specified and as directed.

M&L for preparation of new plastered surface of walls etc and applying two coats of distempering interior walls with distemper oil emulsion white or tinted over chalk whiting complete all as specified and as directed.

M&L for preparation of new plaster surfaces of wall, and applying two coats of water based acrylic weather proof exterior emulsion (Apex ultima superior quality) paint over a coat of primer as per manufacturer's instruction complete all as specified and as directed.

Taking up or down 15 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ceiling etc and keeping serviceable quantity in safe custody for reuse at same site or other site complete all as specified and as directed.

Taking up or down 20 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ceiling etc and keeping serviceable quantity in safe custody for reuse at same site or other site complete all as specified and as directed.

Supply, laying, connection and testing, 15mm bore, steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239 (Part -2):2011 and fixtures fixed to walls and ceilings or laid in floors, etc complete all as specified and as directed.

Supply, laying, connection and testing, 20mm bore, steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239 (Part -2):2011 and fixtures fixed to walls and ceilings or laid in floors, etc complete all as specified and as directed.

Refixing 15mm bore old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed.

Refixing 20 mm bore old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed.

Dismantling of water tank capacity excedding 250 Ltrs and not exceeding 500 Ltrs and removing to store complete all as specified and as directed.

S&F for 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe complete all as specified and as directed.

S&F 20 mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and as directed.

S&F in repairs 20 mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and as directed.

S&F in repairs 15 mm bore, bib taps, chromium plated, fancy type, screwed for iron pipes and fixed complete all as specified and as directed.

S&F in repairs 15 mm bore dia, stop valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F 15 mm bore, pillar taps, fancy type, cast copper alloy, chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F in repairs 15 mm bore, pillar taps, fancy type, cast copper alloy, chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F in repairs swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms) including shower arm 15 mm size, 195mm long with bend of 45 degree with flange of PTMT any colour (Minimum weight 40gms complete all as specified and as directed.

S&F in repairs 15 mm bore, bib taps, PTMT, any colour, high pressure screwed for iron pipes and fixed (minimum weight 15mm-90gms/20mm-125gms) complete all as specified and as directed.

S&F in repairs 15 mm bore, Stop valve, PTMT, any colour, high pressure screwed for iron pipes and fixed (minimum weight 15mm-90gms/20mm-125gms) complete all as specified and as directed.

S&F in repairs 15mm bore, PVC connection pipe 600mm long with PTMT nuts at both ends complete all as specified and as directed.

S&F in repairs casecade health faucet chromium plated including hook and hose not less than 1.2 metre long all as specified and as directed.

S&F in repairs 10 liter capacity, PVC valve less syphonic duel type, flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle including brackets complete all as specified and as directed.

S&F for grating doom, circular type, 100mm dia of PTMT, (mimimum weigh 25 gms) complete all as specified and as directed.

S&F in repairs vitreous china squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rest and 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe (32mm dia) etc complete including making good to disturbed surfaces of floor using concrete (1:2:4) type B0 and to match with existing specifications complete all as specified and as directed.

S&F in repairs semi-pedestal pattern (Anglow-Indian type), vitreous china water closet pan, white, with 'P' or 'S' trap, including flushing pipe and seat & cover for pedestal pattern , etc complete and making good to disturbed surfaces of floor by filling with PCC (1:4:8) type D-2 to match with the existings complete all as specified and as directed.

S&F in repairs vitreous china wash basin, size 550x400mm, white, flat back, with PVC waste pipe, CP waste coupling, chain, plug and porcelain stopper & brackets including cutting for and pinning in ends of brackets but excluding tap complete all as specified and as directed.

S&F in repairs stainless steel kitchen, sinks made of 1 mm thick sheet for kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 485mm x 420mm and bowl size 410mmx330mmx160mm complete all as specified and directed.

S&F in repairs 32/40 mm dia x 800mm long waste pipe for sink/wash basin/ urinal etc complete all as specified and directed.

S&F in repairs 32/40 mm dia waste coupling of PTMT (half or full thread) for sink/wash basin/ urinal etc complete all as specified and directed.

Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ for 100 mm thickness of concrete slab complete all as specified and as directed.

&F in repair 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

S&F in repairs curtain rails, Harrison rail, aluminium alloy with fixing brackets, stops, rollers etc complete all as specified and as directed.

M&L for servicing of steel rolling shutters of size/area upto 21 sqm (single opening), lever operated with rectification of minor defects, overhauling, greasing, lubricating of guide rails and refixing clamps, riveting including necessary repairs to the locking arrangements and replacement of worn-out spare parts such as gear/worm/interlocking laths/ ball bearing in order to bring the rolling shutter easy operation and smooth functioning all as directed. Note : (i) The spare parts will be measured and paid separately as supply only under respective item of this schedule. (ii) Minor/small repair or minor welding if required to be done, the same shall be done at spot without removing the shutter and cost element of this work shall deemed to be included in the quoted rate under this item.

Greasing only rolling shutters of size/area upto 21sqm (single opening) including guide channels complete all as specified and as directed.

S&F in repairs 1 mm thick, mild steel sheet hood cover of hexagonal, square or circular contour depending upon the contour of bracket plates, properly stiffened with MS angle/ flat stiffener at top and bottom edges complete all as directed.

S&F in repairs 50mm bore MS pipe for suspension shafts for rolling shutters complete all as specified and as directed.

S&F in repairs bevel gear box for rolling shutters complete all as specified and as directed.

S&F in repairs crank handle for operating gear, operated rolling shutters complete all as specified and as directed.

M&L in repairs welding thickness of metal exceeding 6mm thick complete all as specified and as directed.

Supply only gear/worm (machine cut) including connection mechanical device and testing complete all as specified and as directed.

Supply only interlocking lath sections made out of cold rolled steel strips of 1.2mm thick and 75mm wide complete all as specified and as directed.

Supply only rolling ball bearing of suitable size for existing rolling shutters complete all as specified and as directed.

S&F for main spring 'O' gauge 450mm long of approved make for existing rolling shutters complete all as specified and as directed.

S&F for safety lever lock mild steel 4 levers suitable for existing rolling shutters complete all as specified and as directed.

M&L for framed mild steel work for door or gate of angle iron or other section with gusset plate, rail, braces, etc complete drilling for fixing of steel sheeting or other coverings. Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging, also fastening and fixing shall conforming to Fe-410 (Gde E-250) complete all as specified and as directed. Note : Steel sheeting or other covering, running rail/ guides shall be measured and paid separately.

M&L for rolled mild steel as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat section) including distance pieces, cleat etc shall conforming to Fe-290 (Gde E-165) complete all as specified and as directed.

S&F for 1.00mm thick plain mild steel black sheet in covering to door, water tank, water trough, hole punched, including round headed screws, clout nails and fixed to wooden or steel frame/members, etc with plain 40mm lap joints or welded/riveted seams including bending, turning up, mitred angles, stopped ends complete all as specified and as directed.

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc.complete all as specified and as directed.

S&F in repairs110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F for 110 mm bore, PVC (SWR) bends of any radius complete all as specified and as directed.

S&F in repairs 75 mm bore, PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

M H KHAN

M/S BORAH BROTHERS

M/S Karen Enterprises

PAUL ENTERPRISE

Shree Trilok Electric Corporation

M/S CHANDAN ENTERPRISE

Garg Brothers